Characterization of polychlorinated dibenzo-p-dioxins and dibenzofurans, dioxin-like polychlorinated biphenyls, and polychlorinated naphthalenes in the environment surrounding secondary copper and aluminum metallurgical facilities in China

Characterization of PCDD/F and dl-PCB levels in air in Gipuzkoa (Basque Country, Spain)

This research examines the levels and trends of pollutants, specifically 17 congeners of PCDD/Fs and 12 dl-PCBs, in the air measured in the province of Gipuzkoa (Basque Country, Spain). The study used PCDD/Fs, dl-PCB, and the sum of dioxin-like compounds as separate response variables. A total of 113 air samples were collected and analyzed using the method described in the European Standard (EN-1948:2006) from two industrial areas. The results were analyzed using non-parametric test to assess the variability of these pollutants based on different factors (year, season and day of the week) and General Linear Models to assess the weight of each factor. The study found that the toxic equivalents (TEQs) for PCDD/Fs were 12.29 fg TEQm^-3 and for dl-PCBs were 1.63 fg TEQm^-3, which were in a similar range or lower than those observed in other national and international studies in industrial areas. The results showed temporal variations, with higher levels of PCDD/Fs in autumn-winter than in spring-summer and higher levels of PCDD/Fs and dl-PCBs during weekdays than on weekends. The industrial area where the energy recovery plant (ERP) will be located had higher levels of air pollutants due to the presence of two PCDD/Fs emitting industries nearby, as indicated by the Spanish Registry of Polluting Emission Sources. Both industrial areas showed similar profiles of PCDD/Fs and dl-PCBs, with the PCDD/F profiles dominated by OCDD, 1,2,3,4,6,7,8-HpCDD, and 1,2,3,4,6,7,8-HpCDF in terms of concentrations and 1,2,3,7,8-PeCDD, 2,3,4,7,8-PeCDF, and 2,3,7,8-TCDD in terms of TEQs. The dl-PCB profiles were dominated by PCB 118, PCB 105, and PCB 77 in terms of concentrations and PCB 126 in terms of TEQs. The findings of this study can serve as an indicator of the potential impact of ERP on the health of the resident population and the environment.

A Review of Polychlorinated Biphenyls (PCBs) Pollution in the Air: Where and How Much Are We Exposed to?

Polychlorinated biphenyls (PCBs) were widely used in industrial and commercial applications, until they were banned in the late 1970s as a result of their significant environmental pollution. PCBs in the environment gained scientific interest because of their persistence and the potential threats they pose to humans. Traditionally, human exposure to PCBs was linked to dietary ingestion. Inhalational exposure to these contaminants is often overlooked. This review discusses the occurrence and distribution of PCBs in environmental matrices and their associated health impacts. Severe PCB contamination levels have been reported in e-waste recycling areas. The occurrence of high PCB levels, notably in urban and industrial areas, might result from extensive PCB use and intensive human activity. Furthermore, PCB contamination in the indoor environment is ten-fold higher than outdoors, which may present expose risk for humans through the inhalation of contaminated air or through the ingestion of dust. In such settings, the inhalation route may contribute significantly to PCB exposure. The data on human health effects due to PCB inhalation are scarce. More epidemiological studies should be performed to investigate the inhalation dose and response mechanism and to evaluate the health risks. Further studies should also evaluate the health impact of prolonged low-concentration PCB exposure.

Determination of polychlorinated naphthalenes in ambient air by isotope dilution gas chromatography-triple quadrupole mass spectrometry

环境空气中的多氯萘(PCNs)一般为痕量水平(pg/m³),要实现其准确定量必然对分析方法的提取、净化和仪器分析提出较高要求。研究通过考察提取溶剂种类、净化流程和色谱-质谱参数,建立了加速溶剂萃取(ASE)-多层硅胶复合中性氧化铝柱的净化方法,并利用同位素稀释气相色谱-三重四极杆质谱(GC-MS/MS)对环境空气中的多氯萘进行测定。同时,通过在采样、提取和进样分析前分别添加同位素内标,开展质量控制和保证。结果表明,在2~100 ng/mL范围内3~8氯萘的平均相对响应因子(RRF)的相对标准偏差(RSD)均小于16%。PCNs同类物的方法检出限为1~3 pg/m³(以样品体积为288 m³计算)。采用基质加标法评价了方法对环境空气样品中PCNs测定的精密度和准确度,低、中、高加标水平下3 ~8氯萘的平均加标回收率分别为89.0%~119.4%、98.6%~122.5%和93.7%~124.5%,测定结果的平均相对标准偏差分别为1.9%~7.0%、1.6%~6.6%和1.0%~4.8%。整个分析过程中,采样内标和提取内标的平均回收率分别为136.2%~146.0%和42.4%~78.1%, RSD分别为5.6%~7.5%和2.7%~17.5%,满足痕量分析的要求且平行性较好。方法的灵敏度和准确度高,精密度良好,适用于环境空气中3~8氯萘的准确定量测定,可在一定程度上缓解多氯萘监测对高分辨气相色谱-高分辨质谱的依赖,为实现多氯萘的国际履约提供方法支持。

Identification of emerging organic pollutants from solid waste incinerations by FT-ICR-MS and GC/Q-TOF-MS and their potential toxicities

Emissions from the incineration of solid waste are a global public health concern, but little attention has been paid to previously unrecognized chemical compounds that are generated by waste incineration and released into the atmosphere. We conducted nontarget analysis of organic chemicals formed during waste incineration by Fourier-transform ion cyclotron resonance mass spectrometry and gas chromatography-quadrupole time-of-flight mass spectrometry. Using toxicity data in the ToxCast library and predicted toxicity data for traditional priority polycyclic aromatic hydrocarbons and 2,3,7,8-tetrachlorodibenzo-p-dioxin, we prioritized 13 compounds including hexachloro-1,3-butadiene, 9 of which are reported here for the first time as constituents of emissions from the incineration of solid waste and hexachloro-1,3-butadiene was included in the Stockholm Convention in 2017. The predicted activity of these pollutants to androgen receptors and to the aryl hydrocarbon receptor were comparable to, or higher than, the 2,3,7,8-tetrachlorodibenzo-p-dioxin and benzo[a]pyrene. In addition, some alkylated polycyclic aromatic hydrocarbons and heteroatom polycyclic aromatic hydrocarbons were also identified in solid waste incineration processes, peak areas of which were 1-2 orders of magnitude higher than dioxins and 1-3 orders of magnitude lower than their parent polycyclic aromatic hydrocarbons. Our study can provide information for better recognizing and regulating the emissions of organic pollutants formed by the incineration of solid waste.

Congener profiles and process distributions of polychlorinated biphenyls, polychlorinated naphthalenes and chlorinated polycyclic aromatic hydrocarbons from secondary copper smelting

Secondary copper smelting is an important industrial source of unintentionally produced persistent organic pollutants (UPOPs) emissions. Herein, field study on industrial-scale plants was conducted to clarify the levels and profiles of polychlorinated biphenyls (PCBs), polychlorinated naphthalenes (PCNs) and chlorinated polycyclic aromatic hydrocarbons (> 3 rings, Cl-PAHs) from secondary copper smelting plants. The three UPOPs emission levels from the oxygen-enriched smelting furnace were higher than that from the anode furnace, which was attributed to the low-grade raw materials used. The toxic equivalent quantity concentrations of Cl-PAHs were 1.3-4.4 and 4.6-18.9 times higher than that of PCBs and PCNs, respectively. Thus, the emission control of Cl-PAHs in the secondary copper industry should be of concern. The chlorination degree of PCBs and PCNs was ~4 after the gas-cooling stage but was reduced to 1-2 in the stack outlet. This result indicated that the PCBs and PCNs congeners that were generated during the cooling stage were mainly higher-chlorinated. After purification by air pollution control devices (APCDs), the high-chlorinated congeners were removed simultaneously with the fly ash, whereas the low-chlorinated congeners may be regenerated and transferred into the stack gas due to possible memory effect within the APCDs.

Environmental contamination and human exposure of polychlorinated biphenyls (PCBs) in China: A review

Polychlorinated biphenyls (PCBs), together with 11 other organic compounds, were initially listed as persistent organic pollutants (POPs) by the Stockholm Convention because of their potential threat to ecosystems and humans. In China, many monitoring studies have been undertaken to reveal the level of PCBs in environment since 2005 due to the introduced stricter environmental regulations. However, there are still significant gaps in understanding the overall spatial and temporal distributions of PCBs in China. This review systematically discusses the occurrence and distribution of PCBs in environmental matrices, organisms, and humans in China. Results showed that PCB contamination in northern and southern China was not significantly different, but the PCB levels in East China were commonly higher than those in West China, which might have been due to the widespread consumption of PCBs and intensive human activities in East China. Serious PCB contamination was found in e-waste disassembling areas (e.g., Taizhou of Zhejiang Province and Qingyuan and Guiyu of Guangdong Province). Higher PCB concentrations were also chronicled in megalopolises and industrial clusters. The unintentionally produced PCBs (UP-PCBs) formed during industrial thermal processes may play an increasingly significant role in PCB pollution in China. Low PCB levels were recorded in rural and underdeveloped districts, particularly in remote and high-altitude localities such as the Tibetan Plateau and the South China Sea. However, these data are limited. Human exposure to PCBs is closely related to the characteristics of environmental pollution. This review also discusses existing issues and future research prospects on PCBs in China. For instance, the accumulation characteristics and migration regularities of PCBs in food webs should be further studied. More investigations should be undertaken to assess the quantitative relationship between external and internal exposure to PCBs. For example, bioaccessibility and bioavailability studies should be supplemented to evaluate human health risks more accurately.

Polychlorinated Biphenyl Emissions from Steelmaking Electric Arc Furnaces

Electric arc furnaces (EAFs) in steelmaking plants are a major source of dioxins. Preheating of steelmaking raw materials is widely used in EAFs to reduce energy consumption. Few studies have investigated emissions of dioxin-like polychlorinated biphenyls (PCBs) from EAFs, and the PCB emission levels and characteristics during preheating are unknown. In this study, PCB concentrations and distributions in stack gases emitted during EAF preheating were determined. The average dioxin-like PCB concentrations in stack gases emitted during preheating of three EAFs were 1236.1, 81,664.4, and 669.8 pg/Nm³, respectively. These values were greatly influenced by the composition of the steelmaking raw materials. The PCB profiles in all samples were dominated by less-chlorinated homologs. PCB emission factor for preheating in the EAFs is 0.58 µg WHO-TEQ/ton averagely, indicating significant emissions of PCBs from preheating process. The data will be useful for developing approaches for preventing and controlling PCB emissions from EAFs.

Particle size distributions and health risks of polychlorinated dibenzo-p-dioxin/furans, polychlorinated biphenyls, and polychlorinated naphthalenes in atmospheric particles around two secondary copper smelters in Shandong Province, China

Sixteen samples of atmospheric particles in four size fractions (diameter: > 10 μm, 5-10 μm, 2.5-5 μm, and <2.5 μm) were collected around two secondary copper smelters in Shandong Province, China. The levels, particle size distributions, and potential health risks of polychlorinated dibenzo-p-dioxin/furans (PCDD/Fs), dioxin-like polychlorinated biphenyls (dl-PCBs), and polychlorinated naphthalenes (PCNs) in these samples were analyzed. The concentration ranges for the PCDD/Fs, dl-PCBs, and PCNs were 3.13-5.77 pg m^-3, 0.43-0.56 pg m^-3, and 4.76-9.89 pg m^-3, respectively. All of the compounds accumulated strongly in the particles with diameters of <2.5 μm. The congener profiles of PCDD/Fs in particles of various sizes were similar, and were consistent with those in stack gases from local secondary copper smelters. However, the congener profiles of dl-PCBs and PCNs in the particles with diameters of <2.5 μm differed from those for the other particle size fractions. The proportion of highly chlorinated homologs in particles with diameters of <2.5 μm was much higher than that of particles with diameters of >2.5 μm. The results of a risk assessment indicated that the contribution of PCDD/Fs to the total carcinogenic risk (PCDD/Fs + dl-PCBs + PCNs) was >95%. For the PCDD/Fs, dl-PCBs, and PCNs, 78%, 71%, and 86% of the carcinogenic risk was associated with the <2.5 μm fraction, respectively. This study improves our understanding of the particle size distributions and human health risks of exposure to PCDD/Fs, dl-PCBs, and PCNs in the atmosphere around secondary copper smelters.

Inhibition Effect and Mechanism of Thiourea on Electrophilic Chlorination of Aromatics in Combustion Flue Gas

Thiourea can effectively inhibit the formation of highly toxic chlorinated aromatics in postcombustion zone. However, the inhibition mechanism was still not adequately understood. In this study, naphthalene was adopted as a model aromatic compound to investigate the inhibition effect and mechanism of thiourea on the formation of chlorinated aromatics via electrophilic chlorination over Cu and Fe chlorides. Thiourea addition resulted in the reductions of 77.6-99.8% and 36.4-98.1% in the yield of polychlorinated naphthalenes from naphthalene chlorination mediated by CuCl₂ and FeCl₃ at 150-300 °C, respectively. The inhibition efficiency of chlorination presented a decreasing tendency with increasing reaction temperature and O₂ content in flue gas. X-ray diffraction analysis revealed that the thiourea-induced reduction of highly active Cu (II) and Fe (III) chlorides to less active Cu (I) and Fe (II) chlorides was a primary mechanism for inhibiting aromatic chlorination. [thiourea-Cu]⁺ complex generated during the reduction process could be transformed into CuS and Cu₂S, and isomeric reaction product NH₄SCN could react with Cu²⁺ to produce Cu(SCN)₂ and then also form Cu sulfides, suggesting sulfidization of Cu chloride was another important inhibition mechanism. Chlorination inhibition induced by the volatile decomposition products of thiourea might only play a minor role.

Passive air sampling for semi-volatile organic chemicals

During passive air sampling, the amount of a chemical taken up in a sorbent from the air without the help of a pump is quantified and converted into an air concentration. In an equilibrium sampler, this conversion requires a thermodynamic parameter, the equilibrium sorption coefficient between gas-phase and sorbent. In a kinetic sampler, a time-averaged air concentration is obtained using a sampling rate, which is a kinetic parameter. Design requirements for kinetic and equilibrium sampling conflict with each other. The volatility of semi-volatile organic compounds (SVOCs) varies over five orders of magnitude, which implies that passive air samplers are inevitably kinetic samplers for less volatile SVOCs and equilibrium samplers for more volatile SVOCs. Therefore, most currently used passive sampler designs for SVOCs are a compromise that requires the consideration of both a thermodynamic and a kinetic parameter. Their quantitative interpretation depends on assumptions that are rarely fulfilled, and on input parameters, that are often only known with high uncertainty. Kinetic passive air sampling for SVOCs is also challenging because their typically very low atmospheric concentrations necessitate relatively high sampling rates that can only be achieved without the use of diffusive barriers. This in turn renders sampling rates dependent on wind conditions and therefore highly variable. Despite the overall high uncertainty arising from these challenges, passive air samplers for SVOCs have valuable roles to play in recording (i) spatial concentration variability at scales ranging from a few centimeters to tens of thousands of kilometers, (ii) long-term trends, (iii) air contamination in remote and inaccessible locations and (iv) indoor inhalation exposure. Going forward, thermal desorption of sorbents may lower the detection limits for some SVOCs to an extent that the use of diffusive barriers in the kinetic sampling of SVOCs becomes feasible, which is a prerequisite to decreasing the uncertainty of sampling rates. If the thermally stable sorbent additionally has a high sorptive capacity, it may be possible to design true kinetic samplers for most SVOCs. In the meantime, the passive air sampling community would benefit from being more transparent by rigorously quantifying and explicitly reporting uncertainty.

Emission characteristics of dl-PCNs, PCDD/Fs, and dl-PCBs from secondary copper metallurgical plants: Control technology and policy

This study investigated the characteristics of dl-PCNs, PCDD/Fs and dl-PCBs emitted from two typical secondary copper metallurgical plants processing copper sludge equipped with different sets of air pollution control devices (APCDs). Results indicated that the emission factors of dl-PCNs and PCDD/Fs of plant A are 0.00775 and 1.09 μg TEQ/ton, respectively, which are remarkably lower than those of plant B (3.12, 181 and 25.5 μg TEQ/ton for dl-PCNs, PCDD/Fs and dl-PCBs, respectively). Dl-PCNs contributed 0.7-2.7% of total TEQ for flue gases and up to 2.6% of TEQ for ash samples. The TEQ concentration of dl-PCNs in fly ash individually exceeds the regulated level of 1 ng TEQ/g regulated by Taiwan EPA, indicating that emission and discharge of dl-PCNs should be regulated. The combination of semidry scrubber and activated carbon injection (ACI) + baghouse (BH) is effective for simultaneous removals of dl-PCNs and PCDD/Fs in plant A; while the combination of cyclone, secondary combustion chamber, ACI + BH and wet scrubber (WS) is not optimal for removing dl-PCNs, PCDD/Fs and dl-PCBs. Memory effect occurring within BH and WS is responsible for low removal efficiencies of these POPs in plant B. This study suggests appropriate APCDs for simultaneous removal of three POP groups and recommends the inclusion of dl-PCNs in emission standard.

Characterization of PCN emission and removal from secondary copper metallurgical processes

This study investigates the characteristics of PCN emission and removal from two secondary copper metallurgical processes (plants A and B) equipped with different air pollution control devices (APCDs). Different operating conditions and feeding materials result in varying emission factors of PCNs from two plants. The average PCN concentration emitted from plant B (7597 ng Nm^-3) is significantly higher than that emitted from plant A (32.5 ng Nm^-3) and those reported in China (5.8-2845 ng Nm^-3). Similar trend is found for fly ash samples collected from two plants. Low chlorinated homologues (Mono-to Tri-CNs) are the major contributors to total PCNs measured in flue gas, fly ash and slag samples. Combination of semi-dry absorber, activated carbon injection and baghouse is effective for PCN removal in plant A, with the overall removal efficiency of 98%. The overall removal efficiency of PCNs achieved with APCDs equipped in plant B is 90%, however, increases of some homologues as the flue gases passing through baghouse and wet scrubber are found, suggesting the occurrence of memory effect within baghouse and wet scrubber.

Levels and characteristics of polychlorinated biphenyls in surface sediments of the Chaobai river, a source of drinking water for Beijing, China

We collected surface sediments from the Chaobai river, the dominant source of drinking water for Beijing, China, to assess the status of contamination by polychlorinated biphenyls and evaluate their sources. Total concentrations of polychlorinated biphenyls in the sediments ranged from 0.125 to 70.6 ng/g dry weight and correlated with the locations relating to painting operation such as printing factories and construction material markets. Dioxin-like polychlorinated biphenyls were present and corresponded with constituents of commercial polychlorinated biphenyl mixtures. Principal component analysis indicated two dominant sources of polychlorinated biphenyls in the sediments-deposition from airborne emissions and point-source pollution from factories. An ecological risk assessment concluded that there was only slight polychlorinated biphenyl pollution in the sediments of the Chaobai river, which was not likely to induce adverse biological effects. Our findings provide information for polychlorinated biphenyl risk assessment and recognition of the dominant sources of these compounds in drinking water in China.

Polychlorinated naphthalenes, polychlorinated dibenzo-p-dioxins and dibenzofurans, and polychlorinated biphenyls in soils in an industrial park in Northwestern China: Levels, source apportionment, and potential human health risks

Seventeen soil samples collected in an industrial park located in Ningxia Province, Northwestern China were analyzed for polychlorinated naphthalenes (PCNs), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), and polychlorinated biphenyls (PCBs). The PCN, PCDD/F, and PCB concentration ranges were 183-3340, 7.00-215, and 45.1-355 pg/g, respectively. Positive matrix factorization showed that secondary ferrous metal smelters and cement kilns contributed more than 70% of the total PCN concentration. Historical use of Halowax 1051 also affected the PCN concentrations in soil. Principal component analysis indicated that the PCDD/F concentrations in soil in the study area were mainly affected by thermal processes in secondary ferrous metal smelters. CB-209 was an important contributor to total PCBs in the study area, and likely originated from the phthalocyanine-type pigments used in a local recycled paper mill. Samples S10, S1, S17, and S6 had high ∑TEQ (PCDD/Fs + PCNs + PCBs) concentrations, and the carcinogenic risks of PCDD/Fs, PCNs, and PCBs for workers from these samples were 0.487 × 10^-6, 0.234 × 10^-6, 0.230 × 10^-6, and 0.210 × 10^-6, respectively. According to our results, the health risks of PCDD/Fs, PCNs, and PCBs for workers in this area should be given more attention.

Inventory of Polychlorinated Naphthalene Emissions from Waste Incineration and Metallurgical Sources in China

Polychlorinated naphthalenes (PCNs) are highly toxic persistent organic pollutants (POPs) that are a relatively new addition to the Stockholm Convention as of 2015. The levels of unintentional emissions of PCNs from important industrial thermal sources on national scales are unclear but are important for understanding potential human exposure. In this study, an inventory was compiled of PCN emissions from priority industrial sources of unintentional POPs in China. Estimated emissions from four typical POP sources in the reference year (2014) in China were 511.6 kg by mass and 7650.8 mg of toxic equivalent. Waste incineration, secondary nonferrous smelting, electric arc furnace steelmaking, and iron ore sintering plants contributed 38.8, 15.4, 29.2, and 16.6%, respectively, to the total emissions. The Eastern Seaboard of China and the Hebei region in North China, which have intensive industrial activity and high population densities, were dominant contributors of PCNs. Only 18.6% of the counties where waste incineration plants were located emitted PCNs at a level higher than 1.00 × 10^-1 mg of toxic equivalent, whereas 80% of the counties where metallurgical plants were located emitted PCNs at this level. These results indicate effective implementation of POP control in the waste incineration industry in China. This study clarifies the unintentionally emission levels of PCNs in China and provides important information for strategy development to control source emissions.

Research on pollution prevention and control BAT of PCDD/Fs in secondary copper industry

Secondary copper industry has received more and more attention due to its high Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) emissions. Best available technologies (BAT) plays an important role in prevention of PCDD/Fs pollution for secondary copper industry and is recommended by the Stockholm Convention on POPs. In this study, AHP-Delphi method-fuzzy comprehensive evaluation method is used to evaluate the 5 smelting technologies that are usually applied in secondary copper industry. The result shows that the Kaldo smelting technology and Ausmelt/ISA smelting technology rank top because of its superior technical performance and good environmental benefits. Then, Kaldo furnace and bag filter were selected as a preliminary validation study on the feasibility of BAT. The results of PCDD/Fs analysis showed that the combination of Kaldo furnace and bag filter can meet the requirements of PCDD/Fs pollution prevention and should be recommended for the treatment of low grades copper scrap.

Gas chromatography-Orbitrap mass spectrometry screening of organic chemicals in fly ash samples from industrial sources and implications for understanding the formation mechanisms of unintentional persistent organic pollutants

Clarifying the occurrences of organic chemicals in fly ash produced during industrial thermal processes is important for improving our understanding of the formation mechanisms of toxic pollutants such as polycyclic aromatic hydrocarbons (PAHs), halogenated PAHs, dioxins, and other unintentional persistent organic pollutants. We developed a highly sensitive gas chromatography-Orbitrap mass spectrometry (GC-Orbitrap/MS) method and applied it to screening of organic pollutants in fly ash samples from multiple industrial thermal processes. The GC-Orbitrap/MS method could detect and quantify organic pollutants at part per billion (ppb) levels. In total, 96 organic chemicals, including alkanes, benzene derivatives, phenols, polycyclic aromatic hydrocarbons, and biphenyl derivatives were identified in the fly ash samples. Several organic chemicals with chlorine or bromine substituents were abundant in secondary copper smelter fly ash, and these might act as precursors for formation of dioxins, brominated dioxins, and other dioxin-like compounds. Several chlorinated and brominated PAH compounds were also found in the secondary copper smelter fly ash. PAHs were dominant chemicals in the secondary aluminum smelter fly ash samples, and were present in much higher concentrations than in the samples from other industries. This indicates that there are different chemical formation pathways in different industries. Possible formation pathways of PAHs and dioxins were investigated and deduced in this study. These results improve our understanding of the formation mechanisms of toxic unintentional persistent organic pollutants and could be useful for reducing their source emissions.

Polychlorinated naphthalene emissions to the atmosphere from typical secondary aluminum smelting plants in southwestern China: concentrations, characterization, and risk evaluation

Secondary aluminum smelting industry, as an important source of polychlorinated naphthalene (PCN) in environment, has been concerned in recent years. To figure out the emission characteristics of PCNs and the potential influence on surrounding environment, two typical secondary aluminum smelting plants were selected and PCNs were determined in flue gas, fly ash, aluminum slag, soil, and air samples collected at and around the plants by GC-MS coupled with DFS. PCN emission factors from the flue gas of the two plants (mean 0.006 ng toxic equivalents/t) were found obviously decreased compared with similar smelting process detected in 2010. The stage of feeding material was still the major PCNs discharge period during the whole smelting process. The total PCN concentrations in air were found to be ranked as following: workshops (290-1917 pg/m³), the area near the workshops (62.3-697 pg/m³), and the surrounding areas (29.9-164 pg/m³, mean 64.5 pg/m³). Similar high concentrations of PCNs were found in soil from by the workshop door (983 ng/g dry weight). Soil-air exchange calculations indicated that mono-CN to tetra-CN would volatilize but hepta-CN and octa-CN would be deposited to the soil. Exposure of plant workers and local inhabitants to PCNs through inhalation was found to be acceptable but higher (especially for workers in the workshops) than living areas. The workshop and the nearby area are potential PCNs polluted areas and should be paid attention during the practical operation.

Emission profiles and formation pathways of 2,3,7,8-substituted and non-2,3,7,8-substituted polychlorinated dibenzo-p-dioxins and dibenzofurans in secondary copper smelters

Secondary copper smelting production is one of the largest polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) emission sources in the world. However, the formations and emissions of non-2,3,7,8-PCDD/Fs have rarely been studied. Toxicology and metabolism studies have proved that non-2,3,7,8-PCDD/Fs may also be toxic to mammals. To better explore the pathways and mechanisms involved in transformation among non-2,3,7,8-PCDD/F and 2,3,7,8-PCDD/F congeners, their full picture was investigated in stack gas and fly ash samples collected in typical secondary copper smelting plants. The concentration ranges for 2,3,7,8-PCDD/Fs and non-2,3,7,8-PCDD/Fs in the stack gas samples were 0.09-5.24 ng/Nm³ and 0.11-7.47 ng/Nm³, respectively. The corresponding concentration ranges in the fly ash samples were 20-2712 ng/g and 2.7-818 ng/g. PCDD/F emissions were mainly from the oxidation stage, and these emissions contributed to 42.6-44.8% of the total emissions from the secondary copper smelting processes. Lower chlorinated PCDD/Fs partitioned more into the stack gas, whereas higher chlorinated PCDD/Fs were more likely to concentrate in the fly ash. Non-2,3,7,8-PCDD/Fs were more likely than 2,3,7,8-PCDD/Fs to associate with the gas phase. Chlorination transformation may occur among PCDD congeners, including 2,3,7,8-PCDD and non-2,3,7,8-PCDD congeners.

Preliminary investigation of polychlorinated dibenzo-p-dioxin and dibenzofuran, polychlorinated naphthalene, and dioxin-like polychlorinated biphenyl concentrations in ambient air in an industrial park at the northeastern edge of the Tibet-Qinghai Plateau, China

Ambient air samples collected in an industrial park at the northeastern edge of the Tibet-Qinghai Plateau (China) were analyzed for polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated naphthalenes (PCNs), and dioxin-like (dl) polychlorinated biphenyls (PCBs). The PCDD/F, PCN, and dl-PCB concentrations were 1.18-2.18, 21.9-75.1, and 0.49-0.90 pg/m³, respectively. The concentrations of these compounds were clearly higher than that observed at a remote site and were comparable with those found in ambient air in industrial areas in other locations. A principal component analysis indicated that emissions from local industrial sites (a secondary aluminum smelter, a cement kiln, and a lead-zinc smelter) at which thermal processes are performed were the sources of PCDD/Fs to the air. The combustion-related PCN congener profiles suggested that industrial thermal processes strongly affect PCN concentrations in ambient air at the industrial park. The results clearly indicated that the industrial park is a source of environmental PCDD/Fs and PCNs at the northeastern edge of the Tibet-Qinghai Plateau.

Emissions of 2,3,7,8-substituted and non-2,3,7,8-substituted polychlorinated dibenzo-p-dioxins and dibenzofurans from secondary aluminum smelters

The secondary aluminum smelting industry is an important source of polychlorinated dibenzo-p-dioxin and dibenzofurans (PCDD/Fs). However, the formations and emissions of non-2,3,7,8-PCDD/Fs have rarely been studied. Non-2,3,7,8-PCDD/Fs may also be metabolically toxic to mammalians. In this study, four typical secondary aluminum smelters were selected as demonstration smelters and the composition of the raw material they used was adjusted to investigate the influence on PCDD/F emissions and profiles. In addition to 17 congeners of 2,3,7,8-PCDD/Fs, 64 congeners of non-2,3,7,8-PCDD/Fs were firstly reported. Strong, positive correlations were found between non-2,3,7,8-PCDD/Fs and 2,3,7,8-PCDD/Fs. The concentrations of 2,3,7,8-PCDD/Fs in stack gas and fly ash samples were 120.7-870.4 pg/Nm³ and 13.40-292.9 ng/g, respectively. Those of non-2,3,7,8-PCDD/Fs in the stack gas and fly ash samples were 84.03-1183.7 pg/Nm³ and 7.20-344.7 ng/g, respectively. The raw material composition was a key factor affecting PCDD/F emissions and profiles. An analysis of Gibbs free energies (ΔG_f) showed that non-2,3,7,8-PCDD/Fs could be transformed into 2,3,7,8-PCDD/Fs, which would increase the PCDD/F environmental risks. The emission inventories of 2,3,7,8-PCDD/Fs, non-2,3,7,8-PCDD/Fs, and International Toxic Equivalents from Chinese secondary aluminum smelters in 2013 were 8247 g, 7253 g, and 608.6 g, respectively. The results of this study could contribute to potential risk evaluations and effective reduction of non-2,3,7,8-PCDD/Fs.

Distribution, seasonal variation and inhalation risks of polychlorinated dibenzo-p-dioxins and dibenzofurans, polychlorinated biphenyls and polybrominated diphenyl ethers in the atmosphere of Beijing, China

Spatial distribution, seasonal variation and potential inhalation risks of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated biphenyls (PCBs) and polybrominated diphenyl ethers (PBDEs) were investigated in the atmosphere of Beijing, using passive air samplers equipped with polyurethane foam disks. Concentrations of ΣPCDD/Fs, ΣPCBs and ΣPBDEs ranged from 8.4 to 179 fg WHO₂₀₀₅-TEQ/m³, 38.6-139 and 1.5-176 pg/m³, respectively. PCDFs showed higher air concentrations than those of PCDDs, indicating the influence of industrial activities and other combustion processes. The non-Aroclor congener, PCB-11, was detected in air (12.3-99.4 pg/m³) and dominated the PCB congener profiles (61.7-71.5% to ∑PCBs). The congener patterns of PBDEs showed signatures from both penta-BDE and octa-BDE products. Levels of PCDD/Fs, PCBs and PBDEs at the industrial and residential sites were higher than those at rural site, indicating human activities in urban area as potential sources. Higher air concentrations of PCDD/Fs, PCBs and PBDEs were observed in summer, which could be associated with atmospheric deposition process, re-volatilization from soil surface and volatilization from use of technical products, respectively. Results of inhalation exposure and cancer risk showed that atmospheric PCDD/Fs, dioxin-like PCBs and PBDEs did not cause high risks to the local residents of Beijing. This study provides further aid in evaluating emission sources, influencing factors and potential inhalation risks of the persistent organic pollutants to human health in mega-cities of China.

Levels, sources, and potential human health risks of PCNs, PCDD/Fs, and PCBs in an industrial area of Shandong Province, China

Polychlorinated naphthalenes (PCNs), polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), and polychlorinated biphenyls (PCBs) are of public concern worldwide because of their persistence and toxicity. To address the human health risks of these pollutants and identify possible sources, soil samples were collected from an industrial area and surrounding residential area in Shandong Province, China. The PCN, PCDD/F, and PCB levels in these samples were determined. Extremely high concentrations of PCNs were detected in two soil samples, and their congener distributions were similar to those of a PCN industrial technical product. The levels of combustion-related PCNs and PCDD/Fs were high in samples collected near a secondary copper smelter. The distribution of total PCB concentrations was similar to that of PCNs. Both historical residues from industrial technical products and emissions from the secondary copper smelter were likely sources of PCNs and PCBs, whereas emissions from the smelter were the main source of PCDD/Fs. A soil sample from near the smelter had a high ΣTEQ concentration (PCDD/Fs + PCBs + PCNs = 18.33 pg TEQ/g) and carcinogenic risk (0.85 × 10^-6) to workers. For all the other samples, the levels of PCDD/Fs, PCBs and PCNs exhibited low carcinogenic and noncarcinogenic risks to workers and residents.

Sources of polychlorinated dibenzo-p-dioxins and dibenzofurans, and biphenyls in Chinese mitten crabs

Polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) and polychlorinated biphenyls (PCBs) in Chinese mitten crabs from several areas were determined. The toxic equivalents (TEQs) for the mean PCDD/F and total PCDD/F and dioxin-like PCBs were 2.9 ± 2.7 and 5.7 ± 4.0 pg TEQ g^-1, respectively. The mean concentrations of PCBs and dl-PCBs were 282 and 59 times the concentrations of PCDD/Fs, respectively. PCDD/F and PCB sources in the crab food web were assessed. The total TEQ of PCDD/F and PCB supplied by crab compound feed was 2.1 times the TEQ in crab meat. Broken corn, aquatic biota, and water contributed around 12% of the total TEQ inputs for crab meat. The contribution from sediment was around 164 times that from crab meat, and sediment may be the most important source of PCDD/Fs and PCBs in cultured crabs. Principal component analysis (PCA) and stable isotope ratios for nitrogen (δ¹⁵N) and carbon (δ¹³C) supported the TEQ results. The mean total PCDD/F and dl-PCB TEQ exposure for humans consuming crabs was 3.4 pg TEQ per kilogram of body weight per day. The PCDD/Fs and PCBs in >80% of the crab samples would not cause the tolerable daily intake to be exceeded.

Characterization of polycyclic aromatic hydrocarbons in soil close to secondary copper and aluminum smelters

A total of 35 surface soil samples around two secondary copper smelters and one secondary aluminum smelter were collected and analyzed for 16 USEPA priority polycyclic aromatic hydrocarbons (PAHs). The concentrations of PAHs were highest when the soil sample sites were closest to the secondary copper smelters. And, a level gradient of PAHs was observed in soil samples according to the distance from two secondary copper smelters, respectively. The results suggested that PAH concentrations in surrounding soils may be influenced by secondary copper smelters investigated, whereas no such gradient was observed in soils around the secondary aluminum smelter. Further analysis revealed that PAH patterns in soil samples also showed some difference between secondary copper and aluminum smelter, which may be attributed to the difference in their fuel and smelting process. PAH patterns and diagnostic ratios indicated that biomass burning may be also an important source of PAHs in the surrounding soil in addition to the emissions from the plants investigated.

Atmospheric occurrence and health risks of PCDD/Fs, polychlorinated biphenyls, and polychlorinated naphthalenes by air inhalation in metallurgical plants

Metallurgical plants are important sources of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), polychlorinated biphenyls (PCBs) and polychlorinated naphthalenes (PCNs). It is significant to evaluate the air levels and human risks of PCDD/Fs, PCBs and PCNs in metallurgical plants considering their adverse effects on human health and thousands of metallurgical plants being in operation in China. The estimated inhalation intakes of PCDD/Fs, PCBs, and PCNs together in eight iron ore sintering plants, three secondary copper plants, four secondary aluminum plants, and one secondary lead plant were 4.9-213.4, 21.4-4026.4, 28.7-630, and 11.7fgTEQkg^-1day^-1, respectively, and the corresponding cancer risks were estimated to be 8.7×10^-7 to 3.8×10^-5, 5.1×10^-6 to 1.1×10^-4, 3.8×10^-6 to 7.1×10^-4, and 2.1×10^-6, respectively. The estimated cancer risk were higher than 100 per million people for three secondary aluminum and copper smelters among the sixteen metallurgical plants, indicating high cancer risks. Stack gas samples from metallurgical plants were also collected and analyzed for comparing their emission profiles with that of air samples. The comparison of PCDD/F, PCB and PCN profiles between air samples and stack gas samples by similarity calculation and principal component analysis suggested the influence of stack gas emissions from metallurgical plants on surrounding air. These results are helpful for understanding the exposure risk to PCDD/Fs, PCBs and PCNs in numerous metallurgical plants being operation in China.

Removal of polychlorinated naphthalenes by desulfurization and emissions of polychlorinated naphthalenes from sintering plant

The sintering flue gas samples were collected at the inlets and outlets of the desulfurization systems to evaluate the influence of the systems on PCNs emission concentrations, profiles, and emission factors. The PCNs concentrations at the inlets and outlets were 27888-153672 pg m(-3) and 11988-42245 pg m(-3),respectively. Desulfurization systems showed excellent removal for PCNs, and the removal efficiencies of PCNs increase with increasing chlorination level. Lower chlorinated homologs are more sensitive to the desulfurization process than higher ones. High levels of PCNs were also detected in the gypsum (11600-29720 pg g(-1)) and fly ash samples (4946-64172 pg g(-1)). The annual total emissions of PCNs released to flue gas and gypsum from the sintering plants were about 394 kg, 48.5% of which was in gypsum. The surface area of the fly ash samples increased significantly from the first to the fourth stage of the series-connected electrostatic precipitator, accompanying obvious rising of concentration of PCNs in the fly ash samples.

Formation and emission of brominated dioxins and furans during secondary aluminum smelting processes

Secondary aluminum smelting (SAl) processes have previously been found to be important sources of polybrominated dibenzo-p-dioxins and dibenzofurans (PBDD/Fs). It is crucial that the key factors that influence the formation and emission of PBDD/Fs are identified to allow techniques for decreasing PBDD/F emissions during SAl processes to be developed. In this study, stack gas samples were collected from four typical secondary aluminum smelters that used different raw materials, and the samples were analyzed to allow differences between PBDD/F emissions from different SAl plants to be assessed. The composition of the raw materials was found to be one of the key factors influencing the amounts of PBDD/Fs emitted. The PBDD/F emission factors (per tonne of aluminum produced) for the plants using 100% (Plant1), 80% (Plant2), and 50% (Plant3) dirty aluminum scrap in the raw material feed were 180, 86, and 14 μg t(-1), respectively. The amounts of PBDD/Fs emitted at different stages of the smelting process (feeding-fusion, refining, and casting) were compared, and the feeding-fusion stage was found to be the main stage in which PBDD/Fs were formed and emitted. Effective aluminum scrap pretreatments could significantly decrease PBDD/F emissions. Much higher polybrominated dibenzofuran concentrations than polybrominated dibenzo-p-dioxin concentrations were found throughout the SAl process. The more-brominated congeners (including octabromodibenzo-p-dioxin, octabromodibenzofuran, heptabromodibenzo-p-dioxins, and heptabromodibenzofurans) were the dominant contributors to the total PBDD/F concentrations. The results could help in the development of techniques and strategies for controlling PBDD/F emissions during metallurgical processes.

Emissions of polychlorinated diphenyl ethers from a municipal solid waste incinerator during the start-up operation

This study examines the emissions of polychlorinated diphenyl ethers (PCDEs) during the start-up processes of a municipal solid waste incinerator (MSWI). Both normal and modified emission control start-ups were tested. Fifteen samples were taken from the flue gas with increasing furnace temperature. Peak PCDE concentrations of 1.48-10.3 ng/Nm(3) were observed at 8-11 h after the start of combustion, when the furnace temperature was in the range of 267-440 °C, that also needed for PCDD/F formation by de novo synthesis. The PCDE emissions could thus, be reduced by current control techniques. Furthermore, the modified control strategies inhibited PCDE formation at the beginning of combustion, and led to an 86% reduction in the maximum PCDE concentration. The overall start-up emissions were calculated as 1.01-3.08 mg, while the annual PCDE emissions with one start-up operation were found to be 7.48-9.64 mg. However, total PCDE emissions will increase by 12-69% if the number of start-up runs increases to between two and eight times per year. Consequently, the prevention of the unnecessary start-ups and advanced activation of the related emission control system are both efficient ways to reduce PCDE emissions.

Two Decades of Environmental Surveillance in the Vicinity of a Waste Incinerator: Human Health Risks Associated with Metals and PCDD/Fs

The concentrations of polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs), as well as the levels of a number of heavy metals, have been periodically measured in samples of soil and vegetation collected around a municipal solid waste incinerator (MSWI) in Tarragona (Catalonia, Spain) for approximately 20 years. Since 2007, the levels of the above-mentioned pollutants have also been determined in air samples by means of either active or passive samplers. In the present study, data regarding the environmental impact of the MSWI, in terms of PCDD/Fs and heavy metals, are updated. The temporal trends of these pollutants were evaluated by comparison with data from previous surveys. In the current survey (2013-2014), mean concentrations of PCDD/Fs in soil, vegetation, and air were 0.63 ng I-TEQ/g, 0.07 ng I-TEQ/g, and 10.1 fg WHO-TEQ/m(3), respectively. Decreases of 47 and 35 % of PCDD/Fs in soil and vegetation, respectively, were observed in relation to the background study (1999). Regarding air samples, a slight temporal decrease of the PCDD/F levels was also found with the remaining concentrations staying nearly constant through time. With respect to metals, notable fluctuations in the concentrations were noted, being dependent on each specific environmental monitor. Overall, the current exposure to PCDD/Fs and metals does not mean any additional health risks for the population living near the facility. In conclusion, the results of the present study show that the environmental impact of the Tarragona MSWI is not significant, in terms of PCDD/Fs and heavy metals, after >20 years of continuous operation.