Polyaniline and polypyrrole: A comparative study of the preparation

Nitrogen-Containing Carbon Tubes Fabricated by Light Irradiation

Cotton-core/polypyrrole (PPy)-sheath fibers (cotton/PPy fibers) were synthesized by aqueous chemical oxidative seeded polymerization and were utilized as precursors for nitrogen-containing carbon (NCC) tubes. Irradiation of the cotton/PPy fibers with a near-infrared (NIR) laser heated them to approximately 300 °C due to light-to-heat photothermal conversion by the PPy, and the cotton core was thermally decomposed and vaporized. Scanning electron microscopy studies revealed the formation of tubes with monodispersed diameters, and elemental microanalysis, Fourier transform infrared spectroscopy, and Raman spectroscopy confirmed that the PPy sheath was converted into NCC. Furthermore, sunlight also worked as the light source in fabricating the NCC tubes. The thicknesses of the tubes were controlled between 410 nm and 2.30 μm by tuning the PPy sheath thickness. The method developed in this study can be extended to other polymeric fibers, including acrylic and wool fibers. The shapes of the cross sections and surface nanomorphologies of the NCC tubes can be reflected in those of the polymer/PPy fibers.

Bioinspired Asymmetric Polypyrrole Membranes with Enhanced Photothermal Conversion for Highly Efficient Solar Evaporation

Solar-driven interfacial evaporation (SDIE) has attracted great attention by offering a zero-carbon-emission solution for clean water production. The manipulation of the surface structure of the evaporator markedly promotes the enhancement of light capture and the improvement of evaporation performance. Herein, inspired by seedless lotus pod, a flexible pristine polypyrrole (PPy) membrane with macro/micro-bubble and nanotube asymmetric structure is fabricated through template-assisted interfacial polymerization. The macro- and micro-hierarchical structure of the open bubbles enable multiple reflections inner and among the bubble cavities for enhanced light trapping and omnidirectional photothermal conversion. In addition, the multilevel structure (macro/micro/nano) of the asymmetric PPy (PPy-A) membrane induces water evaporation in the form of clusters, leading to a reduction of water evaporation enthalpy. The PPy-A membranes achieve a full-spectrum light absorption of 96.3% and high evaporation rate of 2.03 kg m-2  h-1 under 1 sun. Long-term stable desalination is also verified with PPy-A membranes by applying one-way water channel. This study demonstrates the feasibility of pristine PPy membranes in SDIE applications, providing guidelines for modulation of the evaporator topologies toward high-efficient solar evaporation.

Plant Virus Sensor for the Rapid Detection of Bean Pod Mottle Virus Using Virus-Specific Nanocavities

This study presents a miniaturized sensor for rapid, selective, and sensitive detection of bean pod mottle virus (BPMV) in soybean plants. The sensor employs molecularly imprinted polymer technology to generate BPMV-specific nanocavities in porous polypyrrole. Leveraging the porous structure, high surface reactivity, and electron transfer properties of polypyrrole, the sensor achieves a sensitivity of 143 μA ng-1 mL cm-2, a concentration range of 0.01-100,000 ng/mL, a detection time of less than 2 min, and a detection limit of 41 pg/mL. These capabilities outperform those of conventional methods, such as enzyme-linked immunosorbent assays and reverse transcription polymerase chain reactions. The sensor possesses the ability to distinguish BPMV-infected soybean plants from noninfected ones while rapidly quantifying virus levels. Moreover, it can reveal the spatial distribution of virus concentration across distinct leaves, a capability not previously attained by cost-effective sensors for such detailed viral data within a plant. The BPMV-specific nanocavities can also be easily restored and reactivated for multiple uses through a simple wash with acetic acid. While MIP-based sensors for plant virus detection have been relatively understudied, our findings demonstrate their potential as portable, on-site diagnostic tools that avoid complex and time-consuming sample preparation procedures. This advancement addresses a critical need in plant virology, enhancing the detection and management of plant viral diseases.

Conducting polymer-based nanostructured materials for brain-machine interfaces

As scientists discovered that raw neurological signals could translate into bioelectric information, brain-machine interfaces (BMI) for experimental and clinical studies have experienced massive growth. Developing suitable materials for bioelectronic devices to be used for real-time recording and data digitalizing has three important necessitates which should be covered. Biocompatibility, electrical conductivity, and having mechanical properties similar to soft brain tissue to decrease mechanical mismatch should be adopted for all materials. In this review, inorganic nanoparticles and intrinsically conducting polymers are discussed to impart electrical conductivity to systems, where soft materials such as hydrogels can offer reliable mechanical properties and a biocompatible substrate. Interpenetrating hydrogel networks offer more mechanical stability and provide a path for incorporating polymers with desired properties into one strong network. Promising fabrication methods, like electrospinning and additive manufacturing, allow scientists to customize designs for each application and reach the maximum potential for the system. In the near future, it is desired to fabricate biohybrid conducting polymer-based interfaces loaded with cells, giving the opportunity for simultaneous stimulation and regeneration. Developing multi-modal BMIs, Using artificial intelligence and machine learning to design advanced materials are among the future goals for this field. This article is categorized under: Therapeutic Approaches and Drug Discovery > Nanomedicine for Neurological Disease.

Polypyrrole Aerogels: Efficient Adsorbents of Cr(VI) Ions from Aqueous Solutions

Three-dimensional and porous polypyrrole (PPy) aerogels were prepared using a facile two-step procedure in which cryogels were synthesized via the cryopolymerization of pyrrole with iron (III) chloride in the presence of supporting water-soluble polymers (poly(N-vinylpyrrolidone), poly(vinyl alcohol), gelatin, methylcellulose or hydroxypropylcellulose), followed by freeze-drying to obtain aerogels. The choice of supporting polymers was found to affect the morphology, porosity, electrical conductivity, and mechanical properties of PPy aerogels. PPy aerogels were successfully used as adsorbents to remove toxic Cr(VI) ions from aqueous solutions.

Sulfonated PAM/PPy Cryogels with Lowered Evaporation Enthalpy for Highly Efficient Photothermal Water Evaporation

Because of the increasing scarcity of water resources, the desalination of seawater by photothermal evaporation with harvested solar energy has gradually become a popular research topic. The interconnected macroporous cryogel prepared from polymerization and crosslinking below the freezing temperature of the reactant solution has an excellent performance in photothermal water evaporation after loading photothermal materials. In this study, polyacrylamide (PAM) cryogels were prepared by cryo-polymerization and sulfonated in an alkaline solution containing formaldehyde and Na₂SO₃. Importantly, the evaporation enthalpy of water in sulfonated PAM cryogel was reduced to 1187 J·g^-1 due to the introduction of sulfonate groups into PAM, which was beneficial to increase the photothermal evaporation rate and efficiency. The sulfonated PAM cryogels loaded with polypyrrole and the umbrella-shaped melamine foam substrate were combined to form a photothermal evaporation device, and the evaporation rate was as high as 2.50 kg·m^-2·h^-1 under one-sun radiation. Meanwhile, the evaporation rate reached 2.09 kg·m^-2·h^-1 in the 14 wt% high-concentration saline solution, and no salt crystals appeared on the surface of the cryogel after 5 h of photothermal evaporation. Therefore, it was evidenced that the presence of sulfonate groups not only reduced the evaporation enthalpy of water but also prevented salting-out from blocking the water delivery channel during photothermal evaporation, with a sufficiently high evaporation rate, providing a reliable idea of matrix modification for the design of high-efficiency photothermal evaporation materials.

TM-Free and TM-Catalyzed Mechanosynthesis of Functional Polymers

Mechanochemically induced methods are commonly used for the depolymerization of polymers, including plastic and agricultural wastes. So far, these methods have rarely been used for polymer synthesis. Compared to conventional polymerization in solutions, mechanochemical polymerization offers numerous advantages such as less or no solvent consumption, the accessibility of novel structures, the inclusion of co-polymers and post-modified polymers, and, most importantly, the avoidance of problems posed by low monomer/oligomer solubility and fast precipitation during polymerization. Consequently, the development of new functional polymers and materials, including those based on mechanochemically synthesized polymers, has drawn much interest, particularly from the perspective of green chemistry. In this review, we tried to highlight the most representative examples of transition-metal (TM)-free and TM-catalyzed mechanosynthesis of some functional polymers, such as semiconductive polymers, porous polymeric materials, sensory materials, materials for photovoltaics, etc.

Al/SnO2 Nanothermite ESD Desensitization by Means of the Elaboration of Tailored SnO2-Polypyrrole Composites

Incidents can occur when handling energetic materials (EMs) due to their sensitivity to external stimuli. Mechanical (friction, impact) and electrical (electrostatic discharge (ESD)) stimuli can trigger involuntary ignition of EMs. Nanothermites, defined as highly reactive mixtures of a metal and a metal oxide, show interesting reactive properties (high temperature/amount of heat). However, their extreme sensitivity to ESD is a significant drawback in their development. With a sensitivity threshold of lower than a millijoule and considering the human body capacity discharge is a few tens of millijoules, the handling of such energetic mixtures is extremely hazardous. ESD desensitization is therefore of crucial importance for the use of these materials. To achieve this goal, polypyrrole (PPy) conductive polymer was used as an additive within an Al/SnO2 energetic formulation. This polymer is able to easily conduct the electrostatic charges, which is useful to avoid an ignition after a spark stimulus. PPy was added to the nanothermite through the elaboration of SnO2-PPy composites. Delaying the SnO2 introduction time during pyrrole's polymerization (t = 0, 1, 24 h) changed the microstructures of the composites. The various SnO2-PPy composites highlighted that the additive's distribution within the composite is a key component for the modulation of ESD sensitivity. For example, this threshold is higher for a nanothermite formulated with the composite elaborated at t = 0 h (96.5 mJ with 7.5 vol % of polymer) than a composition based on the composite at t = 24 h (16.9 mJ with 8.2 vol % of polymer). Meanwhile, the reactive properties are decreased. The loss of reactivity (e.g. combustion speed) was explained by the thermal insulating property of the additive. Overall, the aim of this study is to help in the understanding of ESD desensitization of nanothermites in order to make them safer for operators and adapted to the required applications.

Copper nanoparticles embedded in polyaniline derived nitrogen-doped carbon as electrocatalyst for bio-energy generation in microbial fuel cells

Microbial fuel cells (SC-MFCs) have emerged as green energy devices to resolve the growing energy and environmental crisis. However, the technology's application depends on the sluggish oxygen reduction reaction (ORR) kinetics. Among the electrocatalysts explored, transition metal-nitrogen-carbon composites exhibit satisfactory ORR activity. Herein, we investigate the performance of copper-nitrogen-carbon (Cu/NC) electrocatalysts for ORR, highlighting the effect of temperature, role of nitrogen functionalities, and Cu-Nx sites in catalyst performance. Cu/NC-700 demonstrated satisfactory ORR activity with an onset potential of 0.7 V (vs. RHE) and a limiting current density of 3.4 mA cm-2. Cu/NC-700 modified MFC exhibited a maximum power density of 489.2 mW m-2, higher than NC-700 (107.3 mW m-2). These observations could result from synergistic interaction between copper and nitrogen atoms, high density of Cu-Nx sites, and high pyridinic-N content. Moreover, the catalyst exhibited superior stability, implying its use in long-term operations. The electrocatalytic performance of the catalyst suggests that copper-doped carbon catalysts could be potential metal-nitrogen-carbon material for scaled-up MFC applications.

In-Situ Oxidative Polymerization of Pyrrole Composited with Cellulose Nanocrystal by Reactive Ink-Jet Printing on Fiber Substrates

A simple and novel method for the deposition of polypyrrole (PPy) and cellulose nanocrystal (CNC) composites on different fiber substrates by reactive ink-jet printing was proposed. PPy/CNCs composites were successfully prepared, and the surface resistance of conductive layer deposited on different fiber substrates is the least when the monomer concentration is 0.6 M. PPy/CNCs were deposited on polyethylene terephthalate (PET) to form a conductive layer by adding polyvinyl alcohol (PVA), and the optimum sintering temperature is 100 °C (monomer/PVA ratio 4.0, conductivity 0.769 S cm⁻¹). The PPy/CNCs conductive layer deposited on the paper has the lowest surface resistance and the best adhesion, and the surface resistance of PPy/CNCs conductive layer decreases first and then increases with the increase of sulfonate concentration. Moreover, the volume of anion in sulfonate will affect the arrangement and aggregation of PPy molecular chain in composite materials. Appropriate sulfonate doping can improve the conductivity and stability of conductive paper, and the maximum conductivity is 0.813 S cm⁻¹. Three devices based on PPy/CNCs conductive paper were proposed and fabricated. Therefore, this ink-jet printing provides a new method for the preparation of conductive materials, sensors, energy storage and electromagnetic shielding, etc.

In situ polymerization and electrical conductivity of polypyrrole/cellulose nanocomposites using Schweizer's reagent

Cellulose-based composites have attracted interest given the shift towards 'green' materials, but achieving uniform dispersions of cellulose in polymer matrices and/or enhancement of interfacial interactions between components remains challenging. Herein we report the preparation of polypyrrole/cellulose nanocomposites in [Cu(NH3)4(H2O)2](OH)2 (Schweizer's reagent/cuoxam)-based reaction media via in situ polymerization. The effect of cellulose template morphology and reaction media on the microstructure, electrical conductivity, and surface wettability was studied. Aqueous reaction media favored the formation of a uniform polypyrrole coating encapsulating the cellulose fibers; concentrated cuoxam solutions promoted inhomogeneity and exhibited a progressive decline in conductivity. The maximum conductivity attained was 3.08 S cm-1 from a bacterial cellulose-templated composite prepared in aqueous reaction media and afforded an approximately threefold increase in conductivity when compared with pure PPy at 1.14 S cm-1. Generally, the composites resembled wetting surfaces - with highly concentrated cuoxam solutions yielding improved hydrophilicity, while substitution of bacterial cellulose with nanocrystalline cellulose engendered a shift towards hydrophobicity. Most composites displayed a contact angle of less than 90° suggesting PPy/cellulose composites tended towards hydrophilic behavior. This study highlights investigations into the viability of cellulose solvents as a facile means to control the structure and performance of in situ functionalized cellulose nanocomposites.

High Thermoelectric Power Generation by SWCNT/PPy Core Shell Nanocomposites

Polypyrrole (PPy) is a conducting polymer with attractive thermoelectric (TE) properties. It is simple to fabricate and modify its morphology for enhanced electrical conductivity. However, such improvement is still limited to considerably enhancing TE performance. In this case, a single-wall carbon nanotube (SWCNT), which has ultrathin diameters and exhibits semi-metallic electrical conductivity, might be a proper candidate to be combined with PPy as a core shell one-dimensional (1D) nanocomposite for higher TE power generation. In this work, core shell nanocomposites based on SWCNT/PPy were fabricated. Various amounts of pyrrole (Py), which are monomer sources for PPy, were coated on SWCNT, along with methyl orange (MO) as a surfactant and ferric chloride as an initiator. The optimum value of Py for maximum TE performance was determined. The results showed that the SWCNT acted as a core template to direct the self-assembly of PPy and also to further enhance TE performance. The TE power factor, PF, and figure of merit, zT, values of the pure PPy were initially recorded as ~1 µW/mK2 and 0.0011, respectively. These values were greatly increased to 360 µW/mK2 and 0.09 for the optimized core shell nanocomposite sample. The TE power generation characteristics of the fabricated single-leg module of the optimized sample were also investigated and confirmed these findings. This enhancement was attributed to the uniform coating and good interaction between PPy polymer chains and walls of the SWCNT through π–π stacking. The significant enhancement in the TE performance of SWCNT/PPy nanocomposite is found to be superior compared to those reported in similar composites, which indicates that this nanocomposite is a suitable and scalable TE material for TE power generation.

Insight into the ion exchange in the adsorptive removal of fluoride by doped polypyrrole from water

In this study, the polypyrrole (PPy) samples doped with Cl^- (PPy-Cl), SO₄^2- (PPy-SO4) and SO₄^2-+Cl^- (PPy-SO4+Cl) were synthesized by chemical polymerization for the adsorptive removal of fluoride ion from water. The structure and morphology of the as-prepared PPy samples were characterized by FT-IR, BET, SEM, XPS, and zeta potential. The adsorption experiments revealed that the PPy-Cl exhibited faster kinetics and higher adsorption capacity (13.98 mg/g), more than 4 times that of PPy-SO4 (3.08 mg/g) and PPy-SO4+Cl (3.17 mg/g). The kinetics of the adsorption followed the pseudo-second-order model and the adsorption isotherm data fitted well to the Langmuir model. FT-IR, EDX, and XPS tests for PPy samples before and after fluoride adsorption demonstrated that anion exchange between F^- and Cl^- or SO4^2- was the prior mechanism for fluoride ion removal from water. Cl^- was more favorable than SO₄^2- in the ion exchange with F^-. Meanwhile, the Cl^- or SO₄^2- exchanged with F^- was mainly bound to the active nitrogen that accounts for 6% of the total nitrogen in PPy molecular matrix. Further study of zeta potential and pH influence experiment demonstrated the electrostatic interaction is auxiliary interaction for the fluoride removal by doped PPy samples.

Intrinsically conductive polymers hybrid bilayer films for the fluorescence molecular diagnosis of the Zika virus

In 2016, the Zika virus (ZIKV) infection became a major public health problem, after the discovery that an alarming increase in the number of Brazilian newborns with microcephaly could be associated with the occurrence of this viral disease during the pregnancy of their mothers. The urgent need for simple diagnostic methods that allow rapid screening of suspected cases has stimulated the search for low-cost devices capable of detecting specific sequences of nucleic acids. The present work describes the development of nanostructured films formed by bilayers of conjugated polymers for rapid detection of the presence of Zika virus DNA, via fluorescence methods. For this, we initially deposited alternating layers of polyaniline (PANI) and polypyrrole (PPY) on the surface of polyethylene terephthalate (PET) sheets. The films obtained were then characterized by SEM, UV-Vis, ATR-FTIR, and contact angle measurements. For their use as quenchers for the diagnosis of Zika, a single DNA strand-specific for ZIKV was labeled with a fluorophore (FAM-ssDNA). We determined the time required for the saturation of the interaction between probe FAM-ssDNA and the film (180 min) and the time for the maximal hybridization between FAM-ssDNA and target DNA to occur (60 min). The detection limits were estimated as 345 pM and 278 pM for the PET/PPY-PANI and PET/PANI-PPY hybrid films, respectively. The simplicity of the procedure, coupled with the fact that a positive/negative response can be obtained in less than 60 min, suggests that the proposal of using these polymeric bilayer films is a promising methodology for the development of rapid molecular diagnostic tests.

Combining ReaxFF Simulations and Experiments to Evaluate the Structure-Property Characteristics of Polymeric Binders in Si-Based Li-Ion Batteries

High energy capacity silicon (Si) anodes in Li-ion batteries incorporate polymeric binders to improve cycle life, which is otherwise limited by large volume and stress fluctuations during charging/discharging cycles. Several properties of the polymeric binder play a role in achieving optimal battery performance, including interfacial adhesion strength, mechanical elasticity, and lithium-ion conduction rate. In this work, we utilize atomistic simulations with the ReaxFF force field and complementary experiments to investigate how these properties dictate the performance of Si/binder anodes. We study three C/N/H-based polymer binders with varying structures (pyrolyzed polyacrylonitrile (PPAN), polyacrylonitrile (PAN), and polyaniline (PANI)) to determine how the structure-property characteristics of the binder affect performance. The Si/binder adhesion analysis reveals some counter-intuitive results: although an individual PANI chain has a stronger affinity to Si compared to PPAN, the PANI bulk binds weaker to the Si surface. Interfacial structural analyses from simulations of the bulk phase show that PANI chains have poor stacking at the interface, while PPAN chains exhibit dense and highly ordered stacking behavior, leading to stronger adhesion. PPAN also has a lower Young's modulus compared to PANI and PAN owing to its ordered and less entangled bulk structure. This added elasticity better accommodates volume changes associated with cycling, making it a more suitable candidate for Si anodes. Finally, both simulations and experimental measurements of Li-ion diffusion rates show higher Li mobility through PPAN than PAN and PANI because the ordered stacking of PPAN chains creates channels that are favorable for Li diffusion to the Si surface. Galvanostatic charge-discharge cycling experiments show that PPAN is indeed a highly promising binder for Si anodes in Li-ion batteries, retaining a capacity of ∼1400 mAh g^-1 for 150 cycles. This work demonstrates that the orientation and structure of the polymer at and near the interface are essential for optimizing binder performance as well as showcases the initial steps for binder evaluation, selection, and application for electrodes in Li-ion batteries.

Multifunctional Cellulose Nanopaper with Superior Water-Resistant, Conductive, and Antibacterial Properties Functionalized with Chitosan and Polypyrrole

Cellulose nanopaper (CNP) has been considered as a promising material with great application potential in diverse fields. However, the hydrophilic nature of CNP significantly limits its practical application. In order to improve its water resistance, we demonstrate a facile approach to functionalize CNP by impregnating it with chitosan (CS), followed by in situ polymerization of polypyrrole (PPy). The results indicate that the obtained CNP/CS/PPy shows excellent water resistance with the wet tensile strength of up to 80 MPa, which is more than 10 times higher than that of the pure CNP. Intriguingly, new features (e.g., electrical conductivity, antibacterial activity, and so forth) are achieved at the same time. The functionalized CNP/CS/PPy shows a high conductivity of 6.5 S cm^-1, which can be used for electromagnetic interference shielding applications with a high shielding performance of around 18 dB. In addition, the CNP/CS/PPy exhibits good antibacterial activity toward Staphylococcus aureus and Escherichia coli, with the bacterial reductions of 99.28 and 95.59%, respectively. Thus, this work provides a simple and versatile approach to functionalize CNP for achieving multifunctional properties.

Monodispersed Nitrogen-Containing Carbon Capsules Fabricated from Conjugated Polymer-Coated Particles via Light Irradiation

Near-infrared (NIR) light irradiation induced the transformation of polypyrrole (PPy) to nitrogen-containing carbon (NCC) material due to its light-to-heat photothermal property. The temperature of the PPy increased over 700 °C within a few seconds by the NIR laser irradiation, and elemental microanalysis confirmed the decreases of hydrogen and chloride contents and increases of carbon and nitrogen contents. Monodispersed polystyrene (PS)-core/PPy shell particles (PS/PPy particles) synthesized by aqueous chemical oxidative seeded polymerization were utilized as a precursor toward monodispersed NCC capsules. When the NIR laser was irradiated to the PS/PPy particles, the temperature rose to approximately 300 °C and smoke was generated, indicating that the PS component forming the core was thermally decomposed and vaporized. Scanning electron microscopy studies revealed the successful formation of spherical and highly monodispersed capsules, and Fourier transform infrared spectroscopy, Raman spectroscopy, and X-ray photoelectron spectroscopy studies confirmed the capsules consisted of NCC materials. Furthermore, sunlight was also demonstrated to work as a light source to fabricate NCC capsules. The size and thickness of the capsules can be controlled between 1 and 80 μm and 146 and 231 nm, respectively, by tuning the size of the original PS/PPy particles and PPy shell thickness.

Preparation of PANI Modified ZnO Composites via Different Methods: Structural, Morphological and Photocatalytic Properties

Polyaniline modified zinc oxide (PANI-ZnO) photocatalyst composites were synthesized by focusing on dissolution disadvantage of ZnO. In-Situ chemical oxidation polymerization method was performed under neutral conditions (PANI-ES) whereas in hybridization method physical blending was applied using emeraldine base of polyaniline (PANI-EB). PANI-ZnO composites were prepared in various ratios of aniline (ANI) to ZnO as 1%, 3%, 6% and 9%. The alterations on the structural and morphological properties of PANI-ZnO composites were compared by Fourier Transform Infrared (FT-IR), Raman Spectroscopy, X-ray Diffraction (XRD) and Scanning Electron Microscopy-Energy Dispersive X-ray Analysis Unit (SEM-EDAX) techniques. FT-IR and Raman spectroscopy confirmed the presence of PANI in all composites. SEM images revealed the morphological differences of PANI-ZnO composites based on PANI presence and preparation methods. Photocatalytic performances of PANI-ZnO specimens were investigated by following the degradation of methylene blue (MB) in aqueous medium under UVA irradiation. The effects of catalyst dose and initial dye concentration were also studied. MB degradation was followed by both decolorization extents and removal of aromatic fractions. PANI-ZnO composites expressed enhanced photocatalytic performance (~95% for both methods) as compared to sole ZnO (~87%). The hybridization method was found to be more efficient than the In-Situ chemical oxidation polymerization method emphasizing the significance of the neutral medium.

Green synthesis of poly(pyrrole methane) for enhanced adsorption of anionic and cationic dyes from aqueous solution

The presence and accumulation of dyestuff in the environment is posing great harm to human beings. In this study, a novel poly(pyrrole methane) (PPm) adsorbent with abundant OH was greenly synthesized via a facile polymerization method. Its physicochemical properties were characterized in detail. Furthermore, the adsorption performance of PPm for anionic dye (acid red G, ARG) and cationic dye (methylene blue, MB) was comparatively studied with a typical dye adsorbent (polyprrrole, PPy). The results revealed that the adsorption of ARG or MB onto PPm followed pseudo-second-order model and Langmuir mode. The adsorption processes were endothermic and spontaneous. The maximum capacities of PPm to adsorb ARG and MB were 555.56 mg/g and 99.11 mg/g, which were about 10 and 2 times higher than that of PPy, respectively. PPm could be reused for 5 cycles without a significant decrease of its adsorption rate. The adsorption of ARG and MB is mainly attributed to electrostatic interaction and hydrogen bonding between ARG or MB and OH in PPm. Additionally, ARG could be adsorbed by ion exchange with the doped Cl^- in PPm. Therefore, this study provides a new strategy to synthesis efficient adsorbent for the removal of both anionic and cationic dyes.

Polyaniline–niobium oxide nanohybrids with photocatalytic activity under visible light irradiation

In this study, we reported the production of polyaniline and niobium oxide hybrids synthesized by the direct reaction between a niobium peroxyoxalate complex and anilinium salt in an aqueous medium.

Hemin-based conjugated effect synthesis of Fe–N/CNT catalysts for enhanced oxygen reduction

Fe/N-codoped carbon nanotubes fabricated through the π–π stacking effect and olefin oxidation polymerization-induced hemin assembly on PPy shows a potential application for ORR.

Polaron and bipolaron induced charge carrier transportation for enhanced photocatalytic H2 production

Photocatalysis is one of the facile approaches for efficient solar energy conversion and storage. However, rapid charge carrier recombination considerably decreases solar to energy conversion efficiency. Herein, polaron and bipolaron rich polypyrrole (PPy) has been utilized as a solid support for effective photogenerated charge carrier separation. Simple oxidative polymerization using a high concentration of ammonium persulfate (APS) induces radical cation/bipolaron formation in PPy due to the cleavage of π-bonds as confirmed by electron paramagnetic resonance spectroscopy (EPR). The formation of radical cations led to an increase of the dielectric constant which retards the charge carrier recombination and thereby enhances the conductivity. Moreover, the polarons and bipolarons induced charge carrier separation in photocatalytic H₂ production was studied with the well-known g-C₃N₄ photocatalyst. It is worth mentioning that compared to bare g-C₃N₄, the PPy supported system showed a drastically enhanced photocatalytic H₂ production rate. A maximum H₂ production rate of 1851 μmoles per g is achieved, which is ∼51 times higher than that of the bare g-C₃N₄ catalyst due to efficient charge carrier separation assisted by radical cations/bipolarons. Thus, utilizing this simple polaron and bipolaron rich PPy solid support could be an effective strategy and alternative for using noble metal cocatalysts to enhance charge carrier separation.

Tuning of Shells in Trilaminar Core@Shell Nanocomposites in Controlling Electromagnetic Interference through Switching of the Shielding Mechanism

Fe₃O₄@SiO₂@PPy core-shell nanocomposites were fabricated by the coating of SiO₂ on Fe₃O₄ through base catalyzed hydrolysis of tetraethyl orthosilicate followed by encapsulation of polypyrrole (PPy). Subsequently, these trilaminar composites have been characterized by Fourier-transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, transmission electron microscopy, Brunauer-Emmett-Teller, superconducting quantum interference devices, and measurement of the total shielding efficiency in the frequency range of 2-8 GHz. Our findings showed the highest total shielding efficiency (∼32 dB) of Fe₃O₄@SiO₂@PPy (Fe₃O₄@SiO₂/pyrrole wt/wt = 1:9) and followed reflection as the dominant shielding mechanism. Such performance was attributed to poor impedance matching between the PPy (conducting)/SiO₂ (insulating) and high electrical conductivity of Fe₃O₄@SiO₂@PPy. Alternatively, electromagnetic (EM) waves incident on the SiO₂@PPy interface could also account for enhancing the total shielding efficiency of Fe₃O₄@SiO₂@PPy because of multireflection/refraction. Our earlier work also showed excellent total shielding efficiency of Fe₃O₄@C@PANI nanocomposites, through absorption as the dominant shielding mechanism. These findings clearly suggest that EM interference shielding in Fe₃O₄@SiO₂@PPy and Fe₃O₄@C@PANI trilaminar core@shell nanocomposites is controlled by tuning of the shells through switching of the mechanism.

Simple Transformation of Covalent Organic Frameworks to Highly Proton-Conductive Electrolytes

We report the rational design and implementation of a new class of gel guest-assisted, ionic covalent organic framework (COF) membranes that exhibit superior H⁺ conduction. The as-synthesized COFs are postmodified via a lithiation (or sodiation) treatment. The hydrophilic Li or Na ions in the COFs form a dense and extensive hydrogen-bonding network of H₂O molecules with mobile H⁺ at the periphery, thereby transforming COFs into H⁺ conductors. Then, the ionic COFs are assembled into a flexible H⁺ conductor membrane via a gelation process, where the organic gel provides both mechanical strength and additional H⁺ carriers for fast H⁺ conduction. The final COF-based membrane exhibits an excellent H⁺ conductivity of 1.3 × 10^-1 S cm^-1 at 313 K and 98% relative humidity, which are the highest values of the COF-based H⁺ conductors reported until now and are even comparable with those of the typical commercial Nafion membrane. We anticipate that the two-in-one strategy would open up a porous COF-driven new molecular framework and membrane architectural design/opportunity for development of next-generation ionic conductors.

MoO3 Nanobelts Embedded Polypyrrole/SIS Copolymer Blends for Improved Electro-Mechanical Dual Applications

This research endeavor aimed to develop thin film blends of polypyrrole (PPy) and poly (styrene-isoprene-styrene) (SIS) with MoO₃ as a nanofiller for improved mechanical and electrical properties to widen its scope in the field of mechatronics. This study reports blends of polypyrrole (PPy) and poly (styrene-isoprene-styrene) (SIS) tri-block copolymer showing improved mechanical and electrical attributes while employing MoO₃ nanobelts as nanofillers that additionally improves the abovementioned properties in the ensuing nanocomposites. The synthesis of PPy/SIS blends and MoO₃/PPy/SIS nanocomposites was well corroborated with XRD, SEM, FTIR, and EDS analysis. Successful blending of PPy was yielded up to 15 w/w% PPy in SIS, as beyond this self-agglomeration of PPy was observed. The results showed a remarkable increase in the conductivity of insulating SIS copolymer from 1.5 × 10^−6.1 to 0.343 Scm⁻¹ and tensile strength up to 8.5 MPa with the 15 w/w% PPy/SIS blend. A further enhancement of the properties was recorded by embedding MoO₃ nanobelts with varying concentrations of the nanofillers into 15 w/w% PPy/SIS blends. The mechanical strength of the polymeric nanocomposites was enhanced up to 11.4 MPa with an increase in conductivity up to 1.51 Scm⁻¹ for 3 w/w% MoO₃/PPy-SIS blends. The resultant product exhibited good potential for electro-mechanical dual applications.

Improved cellular response on functionalized polypyrrole interfaces

Neuroregeneration strategies involve multiple factors to stimulate nerve regeneration. Neural support with chemical and physical cues to optimize neural growth and replacing the lesion neuron and axons are crucial for designing neural scaffolds, which is a promising treatment approach. In this study, polypyrrole polymerization and its functionalization at the interface developed by glycine and gelatin for further optimization of cellular response. Nanofibrous scaffolds were fabricated by electrospinning of polyvinyl alcohol and chitosan solutions. The electrospun scaffolds were polymerized on the surface by pyrrole monomers to form an electroactive interface for further applications in neural tissue engineering. The polymerized polypyrrole showed a positive zeta potential value of 57.5 ± 5.46 mV. The in vitro and in vivo biocompatibility of the glycine and gelatin-functionalized polypyrrole-coated scaffolds were evaluated. No inflammatory cells were observed for the implanted scaffolds. Further, DAPI nucleus staining showed a superior cell attachment on the gelatin-functionalized polypyrrole-coated scaffolds. The topography and tuned positively charged polypyrrole interface with gelatin functionalization is expected to be particularly efficient physical and chemical simultaneous factors for promoting neural cell adhesion.

Green synthesis of conductive polyaniline by Trametes versicolor laccase using a DNA template

The green synthesis of highly conductive polyaniline by using two biological macromolecules, i.e laccase as biocatalyst, and DNA as template/dopant, was achieved in this work. Trametes versicolor laccase B (TvB) was found effective in oxidizing both aniline and its less toxic/mutagenic dimer N-phenyl-p-phenylenediamine (DANI) to conductive polyaniline. Reaction conditions for synthesis of conductive polyanilines were set-up, and structural and electrochemical properties of the two polymers were extensively investigated. When the less toxic aniline dimer was used as substrate, the polymerization reaction was faster and gave less-branched polymer. DNA was proven to work as hard template for both enzymatically synthesized polymers, conferring them a semi-ordered morphology. Moreover, DNA also acts as dopant leading to polymers with extraordinary conductive properties (∼6 S/cm). It can be envisaged that polymer properties are magnified by the concomitant action of DNA as template and dopant. Herein, the developed combination of laccase and DNA represents a breakthrough in the green synthesis of conductive materials.

Enzymatic Formation of Polyaniline, Polypyrrole, and Polythiophene Nanoparticles with Embedded Glucose Oxidase

Polyaniline (PANI), polypyrrole (Ppy), and polythiophene (PTh) composite nanoparticles with embedded glucose oxidase (GOx) were formed by enzymatic polymerization of corresponding monomers (aniline, pyrrole, and thiophene). The influence of monomers concentration, the pH of solution, and the ratio of enzyme/substrate on the formation of PANI/GOx, Ppy/GOx, and PTh/GOx composite nanoparticles were spectrophotometrically investigated. The highest formation rate of PANI-, Ppy-, and PTh-based nanoparticles with embedded GOx was observed in the sodium acetate buffer solution, pH 6.0. The increase of optical absorbance at λ_max = 440 nm, λ_max = 460 nm, and λ_max = 450 nm was exploited for the monitoring of PANI/GOx, Ppy/GOx and PTh/GOx formation, respectively. It was determined that the highest polymerization rate of PANI/GOx, Ppy/GOx, and PTh/GOx composite nanoparticles was achieved in solution containing 0.75 mg mL⁻¹ of GOx and 0.05 mol L⁻¹ of glucose. The influence of the enzymatic polymerization duration on the formation of PANI/GOx and Ppy/GOx composite nanoparticles was spectrophotometrically investigated. The most optimal duration for the enzymatic synthesis of PANI/GOx and Ppy/GOx composite nanoparticles was in the range of 48–96 h. It was determined that the diameter of formed PANI/GOx and Ppy/GOx composite nanoparticles depends on the duration of polymerization using dynamic light scattering technique (DLS), and it was in the range of 41–167 nm and 65–122 nm, when polymerization lasted from 16 to 120 h.

Highly effective bromate reduction by liquid phase catalytic hydrogenation over Pd catalysts supported on core-shell structured magnetites: Impact of shell properties

Liquid phase catalytic reduction of bromate with supported noble metals as the catalysts is a promising method to remove bromate in water. Magnetic supports provide a feasible way to recover catalysts whose surface properties also strongly influence the catalytic efficiency. In this study, Pd nanoparticles supported on core-shell structured magnetites with varied shells (e.g., carbon, SiO₂, polypyrrole, polyaniline, polydopamine and chitosan) were prepared and catalytic reduction of bromate on the catalysts was investigated. The results showed that in comparison with other catalysts Pd/(Fe₃O₄@polyaniline) exhibited a higher catalytic efficiency due to its higher point of zero charge and surface hydrophilicity. In parallel, bromate reduction on Pd/(Fe₃O₄@polyaniline) followed the Langmuir-Hinshelwood model, confirming the crucial role of bromate adsorption. At pH 5.6 and a catalyst dosage of 0.05 g/L, 0.4 mM bromate could be completely reduced into bromide within 120 min. Furthermore, the magnetic catalysts could be effectively separated and recovered under an external magnetic field within 3 min. The results of catalyst reuse showed that after five consecutive catalytic reduction cycles Pd/(Fe₃O₄@polyaniline) retained 87% of its fresh catalyst activity. The present findings indicate that Pd/(Fe₃O₄@polyaniline) with polyaniline as the shell is a highly active, stable and recyclable catalyst for liquid phase catalytic hydrogenation of pollutants in water.

Evolution of Self-Organized Microcapsules with Variable Conductivities from Self-Assembled Nanoparticles at Interfaces

Self-organization dramatically affects the surface properties of materials on a macroscopic scale, such as wettability and adhesion. Fundamentally, it is equally interesting when self-organization at the nanoscale affects the bulk properties and thus provides a means to engineer the optoelectronic properties of the materials on larger scales. In this work, we report the evolution of conductive self-organized polymer microcapsules from a monomer emulsion droplet stabilized by a monolayer of conductive Janus nanoparticles (JNPs) via a mechanism resembling morphogenesis. The wall of the resulting conductive microcapsule has a honeycomb-like structure with highly oriented JNPs occupying each hollow cell. The JNPs consist of an electrically conductive lobe and an insulating lobe; because of their orientation and presence in the honeycomb, the conductivity of the microcapsule is greatly enhanced as compared to that of each of the constituting materials. This method can be universally applied to induce self-organization in conductive polymers forming by oxidative addition.

Formation of Polyaniline and Polypyrrole Nanocomposites with Embedded Glucose Oxidase and Gold Nanoparticles

Several types of polyaniline (PANI) and polypyrrole (Ppy) nanocomposites with embedded glucose oxidase (GOx) and gold nanoparticles (AuNPs) were formed by enzymatic polymerization of corresponding monomers (aniline and pyrrole) in the presence of 6 and 13 nm diameter colloidal gold nanoparticles (AuNPs_(6nm) or AuNPs_(13nm), respectively) or chloroaurate ions (AuCl₄⁻). Glucose oxidase in the presence of glucose generated H₂O₂, which acted as initiator of polymerization reaction. The influence of polymerization bulk composition and pH on the formation of PANI- and Ppy-based nanocomposites was investigated spectrophotometrically. The highest formation rate of PANI- and Ppy-based nanocomposites with embedded glucose oxidase and gold nanoparticles (PANI/AuNPs-GOx and Ppy/AuNPs-GOx, respectively) was observed in the solution of sodium acetate buffer, pH 6.0. It was determined that the presence of AuNPs or AuCl₄⁻ ions facilitate enzymatic polymerization of aniline and pyrrole.