A review of the designs and prominent biomedical advances of natural and synthetic hydrogel formulations

Injectable Carrageenan/Green Graphene Oxide Hydrogel: A Comprehensive Analysis of Mechanical, Rheological, and Biocompatibility Properties

In this work, physically crosslinked injectable hydrogels based on carrageenan, locust bean gum, and gelatin, and mechanically nano-reinforced with green graphene oxide (GO), were developed to address the challenge of finding materials with a good balance between injectability and mechanical properties. The effect of GO content on the rheological and mechanical properties, injectability, swelling behavior, and biocompatibility of the nanocomposite hydrogels was studied. The hydrogels' morphology, assessed by FE-SEM, showed a homogeneous porous architecture separated by thin walls for all the GO loadings investigated. The rheology measurements evidence that G' > G″ over the whole frequency range, indicating the dominant elastic nature of the hydrogels and the difference between G' over G″ depends on the GO content. The GO incorporation into the biopolymer network enhanced the mechanical properties (ca. 20%) without appreciable change in the injectability of the nanocomposite hydrogels, demonstrating the success of the approach described in this work. In addition, the injectable hydrogels with GO loadings ≤0.05% w/v exhibit negligible toxicity for 3T3-L1 fibroblasts. However, it is noted that loadings over 0.25% w/v may affect the cell proliferation rate. Therefore, the nano-reinforced injectable hybrid hydrogels reported here, developed with a fully sustainable approach, have a promising future as potential materials for use in tissue repair.

Advances in Hydrogels Research for Ion Detection and Adsorption

The continuing development of heavy industry worldwide has led to an exponential increase in the amount of wastewater discharged from factories and entering the natural world in the form of rivers and air. As the top of the food chain in the natural world, toxic ions penetrate the human body through the skin, nose, and a few milligrams of toxic ions can often cause irreversible damage to the human body, so ion detection and adsorption is related to the health and safety of human beings. Hydrogel is a hydrophilic three-dimensional reticulated polymer material that first synthesized by Wichterle and Lim in 1960, which is rich in porous structure and has a variety of active adsorption sites as a new type of adsorbent and can be used to detect ions through the introduction of photonic crystals, DNA, fluorescent probe, and other materials. This review describes several synthetic and natural hydrogels for the adsorption and detection of ions and discusses the mechanism of ion adsorption by hydrogels, and provide a perspective for the future development.

Nanoclay-Composite Hydrogels for Bone Tissue Engineering

Nanoclay-composite hydrogels represent a promising avenue for advancing bone tissue engineering. Traditional hydrogels face challenges in providing mechanical strength, biocompatibility, and bioactivity necessary for successful bone regeneration. The incorporation of nanoclay into hydrogel matrices offers a potential unique solution to these challenges. This review provides a comprehensive overview of the fabrication, physico-chemical/biological performance, and applications of nanoclay-composite hydrogels in bone tissue engineering. Various fabrication techniques, including in situ polymerization, physical blending, and 3D printing, are discussed. In vitro and in vivo studies evaluating biocompatibility and bioactivity have demonstrated the potential of these hydrogels for promoting cell adhesion, proliferation, and differentiation. Their applications in bone defect repair, osteochondral tissue engineering and drug delivery are also explored. Despite their potential in bone tissue engineering, nanoclay-composite hydrogels face challenges such as optimal dispersion, scalability, biocompatibility, long-term stability, regulatory approval, and integration with emerging technologies to achieve clinical application. Future research directions need to focus on refining fabrication techniques, enhancing understanding of biological interactions, and advancing towards clinical translation and commercialization. Overall, nanoclay-composite hydrogels offer exciting opportunities for improving bone regeneration strategies.

Designing network structure hydrogels derived from carrageenan- phosphated polymers by covalent and supramolecular interactions for potential biomedical applications

Recently, various efforts have been made to explore the potential of natural polysaccharides derived from sea weeds to promote sustainable development. Herein, carrageenan (CG), a polysaccharide extracted from red sea algae, was utilized to design network structures as hydrogels, aimed at significant applications in drug delivery (DD) systems. Hydrogels were designed by graft copolymerization reaction of poly(bis [2-methacryloyloxy] ethyl phosphate [poly(BMEP)] and poly(acrylic acid) [poly(AAc)] onto CG in the presence of a crosslinking agent. Hydrogels were developed by covalent linkage by graft copolymerization and supramolecular interactions, existing in the copolymers. Copolymers were characterized by Atomic force microscopy (AFM), Fourier transform infrared spectroscopy (FTIR), 13C-nuclear magnetic resonance (NMR), and X-ray diffraction (XRD) instrumentations. The drug diffusion exhibited a sustained pattern due to polymer-drug interactions. The drug release followed non-Fickian diffusion mechanism and the release profile was most accurately depicted by first order kinetic model. The biocompatible nature of the copolymer was demonstrated from the hemolytic index value signifying minimal adverse interactions with blood component upon exposure. A protein adsorption test was performed using bovine serum albumin (BSA), exhibiting 8.15 ± 0.26 % albumin adsorption. Polymers exhibited mucoadhesive character, evidenced by their requirement of a detachment force measuring 195 ± 4.72 mN for separation from the membrane during interactions with the mucosal surface. The hydrogels exhibited antioxidant properties, evidenced by 2, 2'-Diphenylpicrylhydrazyl (DPPH) assay, revealing copolymer capable of scavenging 58.21 ± 2.26 % of free radical. The hydrogel revealed antimicrobial activity against P. aeruginosa and S. aureus bacteria, a property further enhanced in hydrogels with the drug doxycycline. These findings suggest suitability of these hydrogels for biomedical applications, with a significant emphasis on drug delivery.

Bioprinting of Stable Bionic Interfaces Using Piezoresistive Hydrogel Organoelectronics

Bionic tissues offer an exciting frontier in biomedical research by integrating biological cells with artificial electronics, such as sensors. One critical hurdle is the development of artificial electronics that can mechanically harmonize with biological tissues, ensuring a robust interface for effective strain transfer and local deformation sensing. In this study, a highly tissue-integrative, soft mechanical sensor fabricated from a composite piezoresistive hydrogel. The composite not only exhibits exceptional mechanical properties, with elongation at the point of fracture reaching up to 680%, but also maintains excellent biocompatibility across multiple cell types. Furthermore, the material exhibits bioadhesive qualities, facilitating stable cell adhesion to its surface. A unique advantage of the formulation is the compatibility with 3D bioprinting, an essential technique for fabricating stable interfaces. A multimaterial sensorized 3D bionic construct is successfully bioprinted, and it is compared to structures produced via hydrogel casting. In contrast to cast constructs, the bioprinted ones display a high (87%) cell viability, preserve differentiation ability, and structural integrity of the sensor-tissue interface throughout the tissue development duration of 10 d. With easy fabrication and effective soft tissue integration, this composite holds significant promise for various biomedical applications, including implantable electronics and organ-on-a-chip technologies.

Functional Bio-Based Polymeric Hydrogels for Wastewater Treatment: From Remediation to Sensing Applications

In recent years, many researchers have focused on designing hydrogels with specific functional groups that exhibit high affinity for various contaminants, such as heavy metals, organic pollutants, pathogens, or nutrients, or environmental parameters. Novel approaches, including cross-linking strategies and the use of nanomaterials, have been employed to enhance the structural integrity and performance of the desired hydrogels. The evolution of these hydrogels is further highlighted, with an emphasis on fine-tuning features, including water absorption capacity, environmental pollutant/factor sensing and selectivity, and recyclability. Furthermore, this review investigates the emerging topic of stimuli-responsive smart hydrogels, underscoring their potential in both sorption and detection of water pollutants. By critically assessing a wide range of studies, this review not only synthesizes existing knowledge, but also identifies advantages and limitations, and describes future research directions in the field of chemically engineered hydrogels for water purification and monitoring with a low environmental impact as an important resource for chemists and multidisciplinary researchers, leading to improvements in sustainable water management technology.

Expanding the boundaries of silk sericin biomaterials in biomedical applications

Silk sericin (SS) has a long history as a by-product of the textile industry. SS has emerged as a sustainable material for biomedical engineering due to its material properties including water solubility, diverse impact on biological activities including antibacterial and antioxidant properties, and ability to promote cell adhesion and proliferation. This review addresses the origin, structure, properties, extraction, and underlying functions of this protein. An overview of the growing research studies and market evolution is presented, along with highlights of the most common fabrication matrices (hydrogels, bioinks, porous and fibrous scaffolds) and tissue engineering applications. Finally, the future trends with this protein as a multifaceted toolbox for bioengineering are explored, along with the challenges with SS. Overall, the present review can serve as a foundation for the creation of innovative biomaterials utilizing SS as a fundamental building block that hold market potential.

Thermosensitive Polyhedral Oligomeric Silsesquioxane Hybrid Hydrogel Enhances the Antibacterial Efficiency of Erythromycin in Bacterial Keratitis

Bacterial keratitis is a serious ocular infection that can impair vision or even cause blindness. The clinical use of antibiotics is limited due to their low bioavailability and drug resistance. Hence, there is a need to develop a novel drug delivery system for this infectious disease. In this study, erythromycin (EM) was encapsulated into a bifunctional polyhedral oligomeric silsesquioxane (BPOSS) with the backbone of the poly-PEG/PPG urethane (BPEP) hydrogel with the aim of improving the drug efficiency in treating bacterial keratitis. A comprehensive characterization of the BPEP hydrogel was performed, and its biocompatibility was assessed. Furthermore, we carried out the evaluation of the antimicrobial effect of the BPEP-EM hydrogel in S. aureus keratitis using in vivo mouse model. The BPEP hydrogel exhibited self-assembling and thermogelling properties, which assisted the drug loading of drug EM and improved its water solubility. Furthermore, the BPEP hydrogel could effectively bind with mucin on the ocular surface, thereby markedly prolonging the ocular residence time of EM. In vivo testing confirmed that the BPEP-EM hydrogel exerted a potent therapeutic action in the mouse model of bacterial keratitis. In addition, the hydrogel also exhibited an excellent biocompatibility. Our findings demonstrate that the BPEP-EM hydrogel showed a superior therapeutic effect in bacterial keratitis and demonstrated its potential as an ophthalmic formulation.

The application of hydrogels for enamel remineralization

Enamel is composed of numerous uniformly wide, well-oriented hydroxyapatite crystals. It possesses an acellular structure that cannot be repaired after undergoing damage. Therefore, remineralization after enamel defects has become a focal point of research. Hydrogels, which are materials with three-dimensional structures derived from cross-linking polymers, have garnered significant attention in recent studies. Their exceptional properties make them valuable in the application of enamel remineralization. In this review, we summarize the structure and formation of enamel, present the design considerations of hydrogels for enamel remineralization, explore diverse hydrogels types in this context, and finally, shed light on the potential future applications in this field.

An investigation of water status in gelatin methacrylate hydrogels by means of water relaxometry and differential scanning calorimetry

The relationship between molecular structure and water dynamics is a fundamental yet often neglected subject in the field of hydrogels for drug delivery, bioprinting, as well as biomaterial science and tissue engineering & regenerative medicine (TE&RM). Water is a fundamental constituent of hydrogel systems and engages via hydrogen bonding with the macromolecular network. The methods and techniques to measure and reveal the phenomena and dynamics of water within hydrogels are still limited. In this work, differential scanning calorimetry (DSC) was used as a quantitative method to analyze freezable (including free and freezable bound) and non-freezable bound water within gelatin methacrylate (GelMA) hydrogels. Nuclear magnetic resonance (NMR) is a complementary method for the study of water behavior and can be used to measure the spin-relaxation of water hydrogen nuclei, which is related to water dynamics. In this research, nuclear magnetic resonance relaxometry was employed to investigate the molecular state of water in GelMA hydrogels using spin-lattice (T1) and spin-spin (T2) spin-relaxation time constants. The data displays a trend of increasing bound water content with increasing GelMA concentration. In addition, T2 values were further applied to calculate microviscosity and translational diffusion coefficients. Water relaxation under various chemical environments, including different media, temperatures, gelatin sources, as well as crosslinking effects, were also examined. These comprehensive physical data sets offer fundamental insight into biomolecule transport within the GelMA hydrogel system, which ultimately are important for drug delivery, bioprinting, as well as biomaterial science and TE&RM communities.

Engineering biomaterials by inkjet printing of hydrogels with functional particulates

Hydrogels with particulates, including proteins, drugs, nanoparticles, and cells, enable the development of new and innovative biomaterials. Precise control of the spatial distribution of these particulates is crucial to produce advanced biomaterials. Thus, there is a high demand for manufacturing methods for particle-laden hydrogels. In this context, 3D printing of hydrogels is emerging as a promising method to create numerous innovative biomaterials. Among the 3D printing methods, inkjet printing, so-called drop-on-demand (DOD) printing, stands out for its ability to construct biomaterials with superior spatial resolutions. However, its printing processes are still designed by trial and error due to a limited understanding of the ink behavior during the printing processes. This review discusses the current understanding of transport processes and hydrogel behaviors during inkjet printing for particulate-laden hydrogels. Specifically, we review the transport processes of water and particulates within hydrogel during ink formulation, jetting, and curing. Additionally, we examine current inkjet printing applications in fabricating engineered tissues, drug delivery devices, and advanced bioelectronics components. Finally, the challenges and opportunities for next-generation inkjet printing are also discussed.

Graphical Abstract

Functional hydrogels for hepatocellular carcinoma: therapy, imaging, and in vitro model

Hepatocellular carcinoma (HCC) is among the most common malignancies worldwide and is characterized by high rates of morbidity and mortality, posing a serious threat to human health. Interventional embolization therapy is the main treatment against middle- and late-stage liver cancer, but its efficacy is limited by the performance of embolism, hence the new embolic materials have provided hope to the inoperable patients. Especially, hydrogel materials with high embolization strength, appropriate viscosity, reliable security and multifunctionality are widely used as embolic materials, and can improve the efficacy of interventional therapy. In this review, we have described the status of research on hydrogels and challenges in the field of HCC therapy. First, various preparation methods of hydrogels through different cross-linking methods are introduced, then the functions of hydrogels related to HCC are summarized, including different HCC therapies, various imaging techniques, in vitro 3D models, and the shortcomings and prospects of the proposed applications are discussed in relation to HCC. We hope that this review is informative for readers interested in multifunctional hydrogels and will help researchers develop more novel embolic materials for interventional therapy of HCC.

Experimental assessment of biostimulants on mung bean growth on a soilless culture system using superabsorbent pectin based hydrogel

Sustainable agriculture initiatives are needed to ensure the food security of the people all over the world. Soilless cultivation methods using hydrogels may give a revolutionary response as well as a more ecological and productive alternative to conventional farming. This study attempted extraction of pectin from the rind of albedo yellow passion fruit (Passiflora edulis var. flavicarpa Degener)and hydrogels from pectin and activated carbon was compared with pure pectin hydrogel; Pectin- Activated Carbon hydrogels (PAC) showed a microporous structure with excellent hydrophilicity and showed superior water holding capacity. Then the prepared hydrogels were examined with various instrumental techniques like FTIR, SEM, XRD, Raman, BET and rheological properties. In the BET analysis, PAC3 shows the highest surface area of 28.771 m2/g when compared to PAC0 at 15.063 m2/g. The germination experiments were performed using mung beans. This study provides an opportunity for the application of pectin hydrogels in agriculture field specifically for home garden or rooftop cultivation.

Novel feed additive delivers antimicrobial copper and influences fecal microbiota in pigs

Dehydrated alginate beads formulated with copper were synthesized and tested as a feed additive to influence the microbiota in finishing pigs and potentially use them as a preharvest intervention to reduce fecal pathogen shedding. The efficacy of the copper beads was tested in vitro and in vivo. In vitro, Salmonella was significantly (P < 0.05) reduced when in contact with the copper beads solution for up to 6 h, with a 5.4 log CFU/mL reduction over the first hour. Chemical analysis of the soak solutions demonstrated the beads delivered their copper payload gradually over the same period the bactericidal effect was observed. For the in vivo experiments, pigs (n = 48) supplemented with the copper beads experienced significant shifts in their microbiota. Enterobacteriaceae (EB) increased by 1.07 log CFU/g (P < 0.05), while lactic acid bacteria (LAB) decreased by 1.22 log CFU/g (P < 0.05) during the treatment period. When beads were removed from the feed, EB and LAB concentrations returned to baseline, indicating copper beads led to measurable and significant changes in microbial loads. Fecal microbiome analysis conducted to explore additional changes by copper bead supplementation demonstrated that, at the phylum level, there was an increase in Firmicutes, Euryarchaeota, and Acidobacteriota, while at the genus level, an increase in Methanosphaera and Pseudomonas was observed. Measures of copper in swine feces showed values ~20 times higher in the treatment group than in the control group during the treatment period, suggesting that dehydrated alginate copper beads were effective in delivering antimicrobial copper to the animal hindgut.IMPORTANCECopper has long been known to have antimicrobial properties. However, when water-soluble salts are fed to livestock, the copper may rapidly dissolve in gastric contents and fail to reach the gut. Here, specially formulated copper beads are seamlessly incorporated into feed and allow copper to remain longer in the gastrointestinal tract of animals, reach deep into both the foregut and hindgut, and shift microbial populations. The technology delivers antimicrobial copper to the animal hindgut and potentially reduces pathogenic microorganisms before animal slaughter.

Unveiling the versatility of gelatin methacryloyl hydrogels: a comprehensive journey into biomedical applications

Gelatin methacryloyl (GelMA) hydrogels have gained significant recognition as versatile biomaterials in the biomedical domain. GelMA hydrogels emulate vital characteristics of the innate extracellular matrix by integrating cell-adhering and matrix metalloproteinase-responsive peptide motifs. These features enable cellular proliferation and spreading within GelMA-based hydrogel scaffolds. Moreover, GelMA displays flexibility in processing, as it experiences crosslinking when exposed to light irradiation, supporting the development of hydrogels with adjustable mechanical characteristics. The drug delivery landscape has been reshaped by GelMA hydrogels, offering a favorable platform for the controlled and sustained release of therapeutic actives. The tunable physicochemical characteristics of GelMA enable precise modulation of the kinetics of drug release, ensuring optimal therapeutic effectiveness. In tissue engineering, GelMA hydrogels perform an essential role in the design of the scaffold, providing a biomimetic environment conducive to cell adhesion, proliferation, and differentiation. Incorporating GelMA in three-dimensional printing further improves its applicability in drug delivery and developing complicated tissue constructs with spatial precision. Wound healing applications showcase GelMA hydrogels as bioactive dressings, fostering a conducive microenvironment for tissue regeneration. The inherent biocompatibility and tunable mechanical characteristics of GelMA provide its efficiency in the closure of wounds and tissue repair. GelMA hydrogels stand at the forefront of biomedical innovation, offering a versatile platform for addressing diverse challenges in drug delivery, tissue engineering, and wound healing. This review provides a comprehensive overview, fostering an in-depth understanding of GelMA hydrogel's potential impact on progressing biomedical sciences.

Synthesis of novel bioadhesive hydrogels via facile Thiol-Ene click chemistry for wound healing applications

Development of outstanding, cost-effective and elastic hydrogels as bioadhesive using Thiol-Ene click chemistry was verified. The visible light photocrosslinkable hydrogels composed of methacrylated chitosan/2,2'-(Ethylenedioxy) diethanethiol formed in presence of eosin-Y photoinitiator. Such hydrogels hold great promise for wound healing applications due to their tunable properties. Main components of hydrogels were extensively characterized using spectroscopic techniques for chemical analysis, thermal analysis, and topologic nanostructure. Various optimization conditions for best gelation time were investigated. Mechanical properties of tensile strength and elongation at break (%) were verified for best wound healing applications. Optimum hydrogel was subjected to for cytotoxicity and microbial suppression evaluation and in-vivo wound healing test for efficient wound healing evaluations. Our results demonstrate the potential use of injectable hydrogels as valuable bioadhesives in bioengineering and biomedical applications, particularly in wound closure and patches.

Current trend on preparation, characterization and biomedical applications of natural polysaccharide-based nanomaterial reinforcement hydrogels: A review

The tunable properties of hydrogels have led to their widespread use in various biomedical applications such as wound treatment, drug delivery, contact lenses, tissue engineering and 3D bioprinting. Among these applications, natural polysaccharide-based hydrogels, which are fabricated from materials like agarose, alginate, chitosan, hyaluronic acid, cellulose, pectin and chondroitin sulfate, stand out as preferred choices due to their biocompatibility and advantageous fabrication characteristics. Despite the inherent biocompatibility, polysaccharide-based hydrogels on their own tend to be weak in physiochemical and mechanical properties. Therefore, further reinforcement in the hydrogel is necessary to enhance its suitability for specific applications, ensuring optimal performance in diverse settings. Integrating nanomaterials into hydrogels has proven effective in improving the overall network and performance of the hydrogel. This approach also addresses the limitations associated with pure hydrogels. Next, an overview of recent trends in the fabrication and applications of hydrogels was presented. The characterization of hydrogels was further discussed, focusing specifically on the reinforcement achieved with various hydrogel materials used so far. Finally, a few challenges associated with hydrogels by using polysaccharide-based nanomaterial were also presented.

Reversibly Adhesive, Anti-Swelling, and Antibacterial Hydrogels for Tooth-Extraction Wound Healing

Oral wound treatment faces challenges due to the complex oral environment, thus, sealing the wound quickly becomes necessary. Although some materials have achieved adhesion and sterilization, how to effectively solve the contradiction between strong adhesion and on-demand removal remains a challenge. Herein, a reversibly adhesive hydrogel is designed by free radical copolymerization of cationic monomer [2-(acryloyloxy) ethyl] trimethylammonium chloride (ATAC), hydrophobic monomer ethylene glycol phenyl ether acrylate (PEA) and N-isopropylacrylamide (NIPAAm). The cationic quaternary ammonium salts provide electrostatic interactions, the hydrophobic groups provide hydrophobic interactions, and the PNIPAAm chain segments provide hydrogen bonding, leading to strong adhesion. Therefore, the hydrogel obtains an adhesion strength of 18.67 KPa to oral mucosa and can seal wounds fast within 10 s. Furthermore, unlike pure PNIPAAm, the hydrogel has a lower critical solution temperature of 40.3 °C due to the contribution of ATAC and PEA, enabling rapid removal with 40 °C water after treatment. In addition, the hydrogel realizes excellent anti-swelling ratio (≈80%) and antibacterial efficiency (over 90%). Animal experiments prove that the hydrogel effectively reduces inflammation infiltration, promotes collagen deposition and vascular regeneration. Thus, hydrogel as a multi-functional dressing has great application prospects in oral wound management.

Development of nanocellulose hydrogels for application in the food and biomedical industries: A review

As the most abundant and renewable natural resource, cellulose has attracted significant attention and research interest for the production of hydrogels (HGs). To address environmental issues and emerging demands, the benefits of naturally produced HGs include excellent mechanical properties and superior biocompatibility. HGs are three-dimensional networks created by chemical or physical cross-linking of linear or branched hydrophilic polymers and have high capacity for absorption of water and biological fluids. Although widely used in the food and biomedical fields, most HGs are not biodegradable. Nanocellulose hydrogels (NC-HGs) have been extensively applied in the food industry for detection of freshness, chemical additives, and substitutes, as well as the biomedical field for use as bioengineering scaffolds and drug delivery systems owing to structural interchangeability and stimuli-responsive properties. In this review article, the sources, structures, and preparation methods of NC-HGs are described, applications in the food and biomedical industries are summarized, and current limitations and future trends are discussed.

A Fluorescent Hydrogel with AIE Emission for Dehydration-Visualizable Wearable Sensors

Hydrogel-based wearable sensors eventually experience dehydration, which negatively impacts their function, leading to decreased sensitivity. Monitoring the real-time water retention rate and sensing performance of wearable flexible sensors without dismantling them remains a significant difficulty. In this study, a molecule having aggregation-induced emission (AIE) properties in an aqueous environment has been developed and produced, which can combine with anionic guar gum and acrylic acid to create an AIE hydrogel. Wearable sensing electronic devices have the capability to track motion signals at various joints of the human body. Additionally, they can effectively and visually monitor dehydration status during extended periods of operation. The fluorescence intensity of the hydrogel is primarily influenced by the level of aggregation of luminous monomers inside the network. This level of aggregation is predominantly governed by the hydrogel's water retention rate. Hence, the extended duration of hydrogel dehydration can be manifested through alterations in their fluorescence characteristics, which are employed for strain sensing. This approach enables users to assess the water retention of hydrogels with greater efficiency, eliminating the requirement for disassembling them from the completed electrical gadget. In summary, the use of AIE-based fluorescent hydrogels will advance the progress of intelligent wearable electronics.

Photosensitizer-loaded hydrogels: A new antibacterial dressing

Bacterial wound infection has emerged as a pivotal threat to human health worldwide, and the situation has worsened owing to the gradual increase in antibiotic-resistant bacteria caused by the improper use of antibiotics. To reduce the use of antibiotics and avoid the increase in antibiotic-resistant bacteria, researchers are increasingly paying attention to  photodynamic therapy, which uses light to produce reactive oxygen species to kill bacteria. Treating bacteria-infected wounds by photodynamic therapy requires fixing the photosensitizer (PS) at the wound site and maintaining a certain level of wound humidity. Hydrogels are materials with a high water content and are well suited for fixing PSs at wound sites for antibacterial photodynamic therapy. Therefore, hydrogels are often loaded with PSs for treating bacteria-infected wounds via antibacterial photodynamic therapy. In this review, we systematically summarised the antibacterial mechanisms and applications of PS-loaded hydrogels for treating bacteria-infected wounds via photodynamic therapy. In addition, the recent  studies and the research status progresses of novel antibacterial hydrogels are discussed. Finally, the challenges and future prospects of PS-loaded hydrogels are reviewed.

Multifunctional fish-skin collagen-based hydrogel sealant with dual-dynamic-bond cross-linked for rapid hemostasis and accelerated wound healing

Collagen (COL) is the most widespread functional protein. Designing and developing dual-dynamic-bond cross-linked COL adhesive hydrogel sealants with multifunctional is highly advantageous for achieving a superior wound closure effect and hemostasis. In this study, we developed hybrid hydrogels consisting of fish-skin COL, oxidized sodium alginate (OSA), borax and polyvinyl alcohol (PVA) to enhance full-thickness wound healing. The hydrogels were furnished with first-rate self-healing capabilities through the dual-dynamic-bond cross-linking of dynamic Schiff base bonds (COL-OSA) and diol boric acid bonds (OSA-borax) with reversible breakage and re-formation. Moreover, the incorporation of PVA stimulated the formation of hydrogen bonds in the system, bolstering the stability of the hydrogel framework. The prepared hydrogel manifests self-healing, injectability, multifunctional adhesiveness and biodegradability. In vivo assessment of the hemostatic capacity of COSP20 hydrogel was superior to gauze both in the mice liver injury model and mice tail amputation model. In addition, a full-thickness skin wound model in mice revealed that the COSP20 hydrogel facilitated faster wound closure by accelerating reepithelialization, COL deposition and angiogenesis. These findings illustrate the potential of hybrid fish-skin COL-based hydrogels to enhance wound healing and promote rapid tissue repair, and provide new possibilities for the effective utilization of marine fishery resources.

A review of biomacromolecule-based 3D bioprinting strategies for structure-function integrated repair of skin tissues

When skin is damaged or affected by diseases, it often undergoes irreversible scar formation, leading to aesthetic concerns and psychological distress for patients. In cases of extensive skin defects, the patient's life can be severely compromised. In recent years, 3D printing technology has emerged as a groundbreaking approach to skin tissue engineering, offering promising solutions to various skin-related conditions. 3D bioprinting technology enables the precise fabrication of structures by programming the spatial arrangement of cells within the skin tissue and subsequently printing skin replacements either in a 3D bioprinter or directly at the site of the defect. This study provides a comprehensive overview of various biopolymer-based inks, with a particular emphasis on chitosan (CS), starch, alginate, agarose, cellulose, and fibronectin, all of which are natural polymers belonging to the category of biomacromolecules. Additionally, it summarizes artificially synthesized polymers capable of enhancing the performance of these biomacromolecule-based bioinks, thereby composing hybrid biopolymer inks aimed at better application in skin tissue engineering endeavors. This review paper examines the recent advancements, characteristics, benefits, and limitations of biological 3D bioprinting techniques for skin tissue engineering. By utilizing bioinks containing seed cells, hydrogels with bioactive factors, and biomaterials, complex structures resembling natural skin can be accurately fabricated in a layer-by-layer manner. The importance of biological scaffolds in promoting skin wound healing and the role of 3D bioprinting in skin tissue regeneration processes is discussed. Additionally, this paper addresses the challenges and constraints associated with current 3D bioprinting technologies for skin tissue and presents future perspectives. These include advancements in bioink formulations, full-thickness skin bioprinting, vascularization strategies, and skin appendages bioprinting.

Highly efficient and selective removal of anionic dyes from aqueous solutions using polyacrylamide/peach gum polysaccharide/attapulgite composite hydrogels with positively charged hybrid network

To avoid the weakness (lower adsorption rate and selectivity) of peach gum polysaccharide (PGP) and improve the adsorption performance of polyacrylamide (PAAm) hydrogel (lower adsorption capacity), in the present work, the PGP was chemically tailored to afford ammoniated PGP (APGP) and quaternized PGP (QPGP), and attapulgite (ATP) was bi-functionalized with cation groups and carbon‑carbon double bond. Then, PAAm/APGP and PAAm/QPGP/ATP hydrogels were synthesized via redox polymerization. The synthesis procedure and properties of hydrogels were traced by FTIR, SEM, XPS, TGA, TEM, and BET methods, and the dye adsorption performance of the hydrogels was evaluated using the new coccine (NC) and tartrazine (TTZ) aqueous solutions as the model anionic dyes. Effects of initial dye concentration, pH, and ionic strength on the adsorption were investigated. Compared with PAAm/APGP hydrogel, PAAm/APGP/ATP hydrogel exhibits higher adsorption rate, superior adsorption capacity, stability, and selectivity towards anionic dye. The adsorption process of PAAm/QPGP/ATP hydrogel reached equilibrium in about 20 min and followed the pseudo-second-order kinetic model and Langmuir isotherm. The adsorption capacities towards NC and TTZ of PAAm/QPGP/ATP hydrogel were calculated as 873.235 and 731.432 mg/g. This hydrogel adsorbent originating from PAAm, PGP, and ATP shows great promise for application in practical water treatment.

Characterization, Biocompatibility and Antioxidant Activity of Hydrogels Containing Propolis Extract as an Alternative Treatment in Wound Healing

Hydrogels consist of a network of highly porous polymeric chains with the potential for use as a wound dressing. Propolis is a natural product with several biological properties including anti-inflammatory, antibacterial and antioxidant activities. This study was aimed at synthesizing and characterizing a polyacrylamide/methylcellulose hydrogel containing propolis as an active ingredient, to serve as a wound dressing alternative, for the treatment of skin lesions. The hydrogels were prepared using free radical polymerization, and were characterized using scanning electron microscopy, infrared spectroscopy, thermogravimetry, differential scanning calorimetry, swelling capacity, mechanical and rheological properties, UV-Vis spectroscopy, antioxidant activity by the DPPH, ABTS and FRAP assays and biocompatibility determined in Vero cells and J774 macrophages by the MTT assay. Hydrogels showed a porous and foliaceous structure with a well-defined network, a good ability to absorb water and aqueous solutions simulating body fluids as well as desirable mechanical properties and pseudoplastic behavior. In hydrogels containing 1.0 and 2.5% propolis, the contents of total polyphenols were 24.74 ± 1.71 mg GAE/g and 32.10 ± 1.01 mg GAE/g and those of total flavonoids 8.01 ± 0.99 mg QE/g and 13.81 ± 0.71 mg QE/g, respectively, in addition to good antioxidant activity determined with all three methods used. Therefore, hydrogels containing propolis extract, may serve as a promising alternative wound dressing for the treatment of skin lesions, due to their anti-oxidant properties, low cost and availability.

Poly(acrylamide)-co-poly(hydroxyethyl)methacrylate-co-poly(cyclohexyl methacrylate) hydrogel platform for stability, storage and biocatalytic applications of urease

In our present work, an explicit crosslinked thermo-responsive hydrogel platform has been developed, by using polyacrylamide (PAAm), poly(2-hydroxyethyl methacrylate) (PHEMA) and poly(cyclohexyl methacrylate) (PCHMA), and then coupled with urease to yield bioconjugates (BCs). Synergic effect of these polymer units provides thermoresponsive nature, optimum crosslinking with desired swelling behaviour, and stability and improved catalytic to Urease in the resultant BCs. Synthesis of the terpolymer has been achieved by employing HEMA (monomer as well as crosslinker), instead of using the conventional crosslinkers, through free radical solution polymerization technique. Various grades of TRPUBs have been fabricated by varying HEMA and CHMA contents while keeping fixed amounts of AAm. Further, the structural analysis of BCs has been done by fourier transform infra-red spectroscopic study and their thermal stabilities have been studied by thermogravimetric analysis. Urea present in TRPUBs has beenanalysed for its hydrolysis atdifferent temperatures viz., 25 °C, 45 °C and 70 °C. Further, the effect of crosslinking, temperature and reaction time on catalytic activities of TRPUBs has been studied. TRPUBs grades have showna maximum swelling capacity up to 5200 %; excellent catalytic activity even at 70 °C; and 85 % activity retention after 18 days storage in buffer medium.

A review of recent advances of cellulose-based intelligent-responsive hydrogels as vehicles for controllable drug delivery system

To realize the maximum therapeutic activity of medicine and protect the body from the adverse effects of active ingredients, drug delivery systems (DDS) featured with targeted transportation sites and controllable release have captured extensive attention over the past decades. Hydrogels with unique three-dimensional (3D) porous structures present tunable capacity, controllable degradation, various stimuli sensitivity, therapeutic agents encapsulation, and loaded drugs protection properties, which endow hydrogels with bred-in-the-bone advantages as vehicles for drug delivery. In recent years, with the impressive consciousness of the "back-to-nature" concept, biomass materials are becoming the 'rising star' as the hydrogels building blocks for controlled drug release carriers due to their biodegradability, biocompatibility, and non-toxicity properties. In particular, cellulose and its derivatives are promising candidates for fabricating hydrogels as their rich sources and high availability, and various smart cellulose-based hydrogels as targeted carriers under exogenous such as light, electric field, and magnetic field or endogenous such as pH, temperature, ionic strength, and redox gradients. In this review, we summarized the main synthetic strategies of smart cellulose-based hydrogels including physical and chemical cross-linking, and illustrated the detailed intelligent-responsive mechanism of hydrogels in DDS under external stimulus. Additionally, the ongoing development and challenges of cellulose-based hydrogels in the biomedical field are also presented.

Hydrogel: a new material for intravesical drug delivery after bladder cancer surgery

The standard treatment for non-muscle invasive bladder cancer (NMIBC) is transurethral resection of bladder tumor (TURBT). However, this procedure may miss small lesions or incompletely remove them, resulting in cancer recurrence or progression. As a result, intravesical instillation of chemotherapy or immunotherapy drugs is often used as an adjunctive treatment after TURBT to prevent cancer recurrence. In the traditional method, drugs are instilled into the patient's bladder through a urinary catheter under sterile conditions. However, this treatment exposes the bladder mucosa to the drug directly, leading to potential side effects like chemical cystitis. Furthermore, this treatment has several limitations, including a short drug retention period, susceptibility to urine dilution, low drug permeability, lack of targeted effect, and limited long-term clinical efficacy. Hydrogel, a polymer material with a high-water content, possesses solid elasticity and liquid fluidity, making it compatible with tissues and environmentally friendly. It exhibits great potential in various applications. One emerging use of hydrogels is in intravesical instillation. By employing hydrogels, drug dilution is minimized, and drug absorption, retention, and persistence in the bladder are enhanced due to the mucus-adhesive and flotation properties of hydrogel materials. Furthermore, hydrogels can improve drug permeability and offer targeting capabilities. This article critically examines the current applications and future prospects of hydrogels in the treatment of bladder cancer.

Recent advances of electrospray technique for multiparticulate preparation: Drug delivery applications

The electrospray (ES) technique has proven to be an effective and a versatile approach for crafting drug delivery carriers with diverse dimensions, multiple layers, and varying morphologies. Achieving the desired particle properties necessitates careful optimization of various experimental parameters. This review delves into the most prevalent ES system configurations employed for this purpose, such as monoaxial, coaxial, triaxial, and multi-needle setups with solid or liquid collector. In addition, this work underscores the significance of ES in drug delivery carriers and its remarkable ability to encapsulate a wide spectrum of therapeutic agents, including drugs, nucleic acids, proteins, genes and cells. Depth examination of the critical parameters governing the ES process, including the choice of polymer, surface tension, voltage settings, needle size, flow rate, collector types, and the collector distance was conducted with highlighting on their implications on particle characteristics, encompassing morphology, size distribution, and drug encapsulation efficiency. These insights illuminate ES's adaptability in customizing drug delivery systems. To conclude, this review discusses ES process optimization strategies, advantages, limitations and future directions, providing valuable guidance for researchers and practitioners navigating the dynamic landscape of modern drug delivery systems.

Advances in chitosan and chitosan derivatives for biomedical applications in tissue engineering: An updated review

In recent years, chitosan (CS) has received much attention as a functional biopolymer for various applications, especially in the biomedical field. It is a natural polysaccharide created by the chemical deacetylation of chitin (CT) that is nontoxic, biocompatible, and biodegradable. This natural polymer is difficult to process; however, chemical modification of the CS backbone allows improved use of functional derivatives. CS and its derivatives are used to prepare hydrogels, membranes, scaffolds, fibers, foams, and sponges, primarily for regenerative medicine. Tissue engineering (TE), currently one of the fastest-growing fields in the life sciences, primarily aims to restore or replace lost or damaged organs and tissues using supports that, combined with cells and biomolecules, generate new tissue. In this sense, the growing interest in the application of biomaterials based on CS and some of its derivatives is justifiable. This review aims to summarize the most important recent advances in developing biomaterials based on CS and its derivatives and to study their synthesis, characterization, and applications in the biomedical field, especially in the TE area.

Chitosan Poly(vinyl alcohol) Methacrylate Hydrogels for Tissue Engineering Scaffolds

A major challenge in tissue engineering scaffolds is controlling scaffold degradation rates during healing while maintaining mechanical properties to support tissue formation. Hydrogels are three-dimensional matrices that are widely applied as tissue scaffolds based on their unique properties that can mimic the extracellular matrix. In this study, we develop a hybrid natural/synthetic hydrogel platform to tune the properties for tissue engineering scaffold applications. We modified chitosan and poly(vinyl alcohol) (PVA) with photo-cross-linkable methacrylate functional groups and then synthesized a library of chitosan PVA methacrylate hydrogels (ChiPVAMA) with two different photoinitiators, Irgacure 2959 (I2959) and lithium phenyl-2,4,6-trimethylbenzoylphosphinate (LAP). ChiPVAMA hydrogels showed tunability in degradation rates and mechanical properties based on both the polymer content and photoinitiator type. This tunability could enable their application in a range of tissue scaffold applications. In a 2D scratch wound healing assay, all hydrogel samples induced faster wound closure compared to a gauze clinical wound dressing control. NIH/3T3 cells encapsulated in hydrogels showed a high viability (∼92%) over 14 days, demonstrating the capacity of this system as a supportive cell scaffold. In addition, hydrogels containing a higher chitosan content demonstrated a high antibacterial capacity. Overall, ChiPVAMA hydrogels provide a potential tissue engineering scaffold that is tunable, degradable, and suitable for cell growth.

Subcutaneous Application of a Gelatin/Hyaluronic Acid Hydrogel Induces the Production of Skin Extracellular Matrix

The development of injectable hydrogels with natural biopolymers such as gelatin (Ge) and hyaluronic acid (Ha) is widely performed due to their biocompatibility and biodegradability. The combination of both polymers crosslinked with N-Ethyl-N'-(3-dimethyl aminopropyl) carbodiimide hydrochloride (EDC) can be used as an innovative dermal filler that stimulates fibroblast activity and increases skin elasticity and tightness. Thus, crosslinked Ge/Ha hydrogels with different concentrations of EDC were administered subcutaneously to test their efficacy in young and old rats. At higher EDC concentrations, the viscosity decreases while the particle size of the hydrogels increases. At all concentrations of EDC, amino and carboxyl groups are present. The histological analysis shows an acute inflammatory response, which disappears seven days after application. At one and three months post-treatment, no remains of the hydrogels are found, and the number of fibroblasts increases in all groups in comparison with the control. In addition, the elastic modulus of the skin increases after three months of treatment. Because EDC-crosslinked Ge/Ha hydrogels are biocompatible and induce increased skin tension, fibroblast proliferation, and de novo extracellular matrix production, we propose their use as a treatment to attenuate wrinkles and expression lines.

Pyrogallol loaded chitosan-based polymeric hydrogel for controlling Acinetobacter baumannii wound infections: Synthesis, characterization, and topical application

Antibacterial hydrogels have emerged as a promising approach for wound healing, owing to their ability to integrate antibacterial agents into the hydrogel matrix. Benefiting from its remarkable antibacterial and wound-healing attributes, pyrogallol has been introduced into chitosan-gelatin for the inaugural development of an innovative antibacterial polymeric hydrogel tailored for applications in wound healing. Hence, we observed the effectiveness of pyrogallol in inhibiting the growth of A. baumannii, disrupting mature biofilms, and showcasing robust antioxidant activity both in vitro and in vivo. In addition, pyrogallol promoted the migration of human epidermal keratinocytes and exhibited wound healing activity in zebrafish. These findings suggest that pyrogallol holds promise as a therapeutic agent for wound healing. Interestingly, the pyrogallol-loaded chitosan-gelatin (Pyro-CG) hydrogel exhibited enhanced mechanical strength, stability, controlled drug release, biodegradability, antibacterial activity, and biocompatibility. In vivo results established that Pyro-CG hydrogel promotes wound closure and re-epithelialization in A. baumannii-induced wounds in molly fish. Therefore, the prepared Pyro-CG polymeric hydrogel stands poised as a potent and promising agent for wound healing with antibacterial properties. This holds considerable promise for the development of effective therapeutic interventions to address the increasing menace of A. baumannii-induced wound infections.

A ternary composite hydrogel based on sodium alginate, carboxymethyl cellulose and copper-doped 58S bioactive glass promotes cutaneous wound healing in vitro and in vivo

Hydrogels offer a novel approach to wound repair. In this study, we synthesized a ternary composite using sodium alginate (SA), carboxymethyl cellulose (CMC) and copper-doped 58S bioactive glass (BG). According to our mechanical testing results, the composite made of 7 wt% CMC and 7 wt% BG (SA-7CMC-7BG) showed optimal properties. In addition, our in vitro studies revealed the biocompatibility and bioactivity of SA-7CMC-7BG, with a negative zeta potential of -31.7 mV. Scanning electron microscope (SEM) images showed 273-μm-diameter pores, cell adhesion, and anchoring. The SA-7CMC-7BG closed 90.4 % of the mechanical scratch after 2 days. An in vivo wound model using Wistar rats showed that SA-7CMC-7BG promoted wound healing, with 85.57 % of the wounds healed after 14 days. Treatment with the SA-7CMC-7BG hydrogel caused a 1.6-, 65-, and 1.87-fold increase in transforming growth factor beta (TGF-β), Col I, and vascular endothelial growth factor (VEGF) expression, respectively that prevents fibrosis and promotes angiogenesis. Furthermore, interleukin 1β (IL-1β) expression was downregulated by 1.61-fold, indicating an anti-inflammatory effect of SA-7CMC-7BG. We also observed an increase in epidermal thickness, the number of fibroblast cells, and collagen deposition, which represent complementary pathology results confirming the effectiveness of the SA-7CMC-7BG hydrogel in cutaneous wound healing.

Tailoring the properties of composite scaffolds with a 3D-Printed lattice core and a bioactive hydrogel shell for tissue engineering

The optimal performance of scaffolds for tissue engineering relies on a proper combination of their constituent biomaterials and on the design of their structure. In this work, composite scaffolds with a core-shell architecture are realized by grafting a gelatin-chitosan hydrogel onto a 3D-printed polylactic acid (PLA) core, aiming in particular at bone regeneration. This hydrogel was recently found to sustain osteogenic differentiation of mesenchymal stromal cells, leading to new bone tissue formation. Here, the integration with rigid PLA lattice structures provides improved mechanical support and finer control of strength and stiffness. The core is prepared by fused deposition modeling with the specific aim to study several lattice structures and thereby better tune the scaffold mechanical properties. In fact, the core architecture dictates the scaffold strength and stiffness, which are seen to match those of different types of bone tissue. For all lattice types, the hydrogel is found to penetrate throughout the entire core and to present highly interconnected pores for cell colonization. By varying the void volume fraction in the core it is possible to significantly change the bioactive shell content, as well as the mechanical properties, over a wide range of values. Looking for design guidelines, relationships between stiffness/strength and density are here outlined for scaffolds featuring different lattice parameters. Moreover, by acting on the core strut arrangement, scaffolds are reinforced along specific directions, as evaluated under compressive and bending loading conditions.

Conductive and Eco-friendly Biomaterials-based Hydrogels for Noninvasive Epidermal Sensors: A Review

As noninvasive wearable electronic devices, epidermal sensors enable continuous, real-time, and remote monitoring of various human physiological parameters. Conductive biomaterials-based hydrogels as sensor matrix materials have good biocompatibility, biodegradability, and efficient stimulus response capabilities and are widely applied in motion monitoring, healthcare, and human-machine interaction. However, biomass hydrogel-based epidermal sensing devices still need excellent mechanical properties, prolonged stability, multifunctionality, and extensive practicality. Therefore, this paper reviews the common biomass hydrogel materials for epidermal sensing (proteins, polysaccharides, polyphenols, etc.) and the various types of noninvasive sensing devices (strain/pressure sensors, temperature sensors, glucose sensors, electrocardiograms, etc.). Moreover, this review focuses on the strategies of scholars to enhance sensor properties, such as strength, conductivity, stability, adhesion, and self-healing ability. This work will guide the preparation and optimization of high-performance biomaterials-based hydrogel epidermal sensors.

Harnessing the power of biological macromolecules in hydrogels for controlled drug release in the central nervous system: A review

Hydrogels have immense potential in revolutionizing central nervous system (CNS) drug delivery, improving outcomes for neurological disorders. They serve as promising tools for controlled drug delivery to the CNS. Available hydrogel types include natural macromolecules (e.g., chitosan, hyaluronic acid, alginate), as well as hybrid hydrogels combining natural and synthetic polymers. Each type offers distinct advantages in terms of biocompatibility, mechanical properties, and drug release kinetics. Design and engineering considerations encompass hydrogel composition, crosslinking density, porosity, and strategies for targeted drug delivery. The review emphasizes factors affecting drug release profiles, such as hydrogel properties and formulation parameters. CNS drug delivery applications of hydrogels span a wide range of therapeutics, including small molecules, proteins and peptides, and nucleic acids. However, challenges like limited biodegradability, clearance, and effective CNS delivery persist. Incorporating 3D bioprinting technology with hydrogel-based CNS drug delivery holds the promise of highly personalized and precisely controlled therapeutic interventions for neurological disorders. The review explores emerging technologies like 3D bioprinting and nanotechnology as opportunities for enhanced precision and effectiveness in hydrogel-based CNS drug delivery. Continued research, collaboration, and technological advancements are vital for translating hydrogel-based therapies into clinical practice, benefiting patients with CNS disorders. This comprehensive review article delves into hydrogels for CNS drug delivery, addressing their types, design principles, applications, challenges, and opportunities for clinical translation.

Poly(vinyl alcohol)/chitosan hydrogel incorporating chitooligosaccharide-gentisic acid conjugate with antioxidant and antibacterial properties as a potential wound dressing

The design and development of wound dressing with antioxidant and antibacterial properties to accelerate wound healing remain challenging. In this study, we synthesize a chitooligosaccharide-gentisic acid (COS-GSA) conjugate using the free-radical grafting method, and fabricate a poly(vinyl alcohol) (PVA)/chitosan (CH)/COS-GSA (PVA/CH/CG) hydrogel using a freeze-thaw method. We characterize the synthesized COS-GSA conjugates using through polyphenol assay, absorbance, and 1H NMR spectroscopy and evaluate their antioxidant properties. The COS-GSA conjugates are successfully synthesized and exhibit better antioxidant properties than pristine COSs. Subsequently, the fabricated hydrogel is characterized based on its morphological analysis, rheological properties, water contact angle, swelling, degradation, water retention properties, and COS-GSA release profiles. Finally, the biocompatibility of the fabricated hydrogel is evaluated on HDF and HaCaT cells through indirect and direct cytotoxicity. The PVA/CH/CG hydrogel exhibited significantly higher antioxidant properties (DPPH, 2,2'-azino-bis(3-ethylbenzothiazoline-6-sulfonic acid) (ABTS), and hydrogen peroxide (H2O2) scavenging activities) and antibacterial activities (Staphylococcus aureus and Pseudomonas aeruginosa) compared to other fabricated hydrogels such as PVA, PVA/CH, and PVA/CH/COS (PVA/CH/C). These results provide evidence that PVA/CH/CG hydrogels with antioxidant, antibacterial, and non-cytotoxic properties have great potential for wound-dressing applications.

Development of hydrogel-based composite scaffolds containing eggshell particles for bone regeneration applications

This study describes the development and characterization of novel composite scaffolds, made of an alginate-chitosan hydrogel matrix containing eggshell (ES) particles, for bone tissue engineering applications. Scaffolds with ES particles, either untreated or treated with phosphoric acid to create a nanotextured particle surface, were compared to scaffolds without particles. Results indicate that the nanotexturing process exposed occluded ES proteins orthologous to those in human bone extracellular matrix. Scaffolds with ES or nanotextured ES (NTES) particles had a higher porosity (81 ± 4% and 89 ± 5%, respectively) than scaffolds without particles (59 ± 5%) (p = .002 and p < .001, respectively). Scaffolds with NTES particles had a larger median pore size (113 μm [interquartile range [IQ]: 88-140 μm]) than scaffolds with ES particles (94 μm [IQ: 75-112 μm]) and scaffolds without particles (99 μm [IQ: 74-135 μm]) (p < .001 and p = .011, respectively). The compressive modulus of the scaffolds with ES or NTES particles remained low (3.69 ± 0.70 and 3.14 ± 0.62 kPa, respectively), but these scaffolds were more resistant to deformation following maximum compression than those without particles. Finally, scaffolds with ES or NTES particles allowed better retention of human mesenchymal stem cells during seeding (53 ± 12% and 57 ± 8%, respectively, vs. 17 ± 5% for scaffolds without particles; p < .001 in both cases), as well as higher cell viability up to 21 days of culture (67 ± 17% and 61 ± 11%, respectively, vs. 15 ± 7% for scaffolds without particles; p < .001 in both cases). In addition, alkaline phosphatase (ALP) activity increased up to 558 ± 164% on day 21 in the scaffolds with ES particles, and up to 567 ± 217% on day 14 in the scaffolds with NTES particles (p = .006 and p = .002, respectively, relative to day 0). Overall, this study shows that the physicochemical properties of the alginate-chitosan hydrogel scaffolds with ES or NTES particles are similar to those of cancellous bone. In addition, scaffolds with particles supported early osteogenic differentiation and therefore represent a promising new bone substitute, especially for non-load bearing applications.

Hydrogel-based Drug Delivery System in Diabetes Management

BACKGROUND

It is estimated that there are over 200 million people living with diabetes mellitus (DM) all over the world. It is a metabolic condition caused by decreased insulin action or secretion. Diabetes Mellitus is also known as Type 2 Diabetes Mellitus. Type 1 diabetes mellitus and type 2 diabetes mellitus are the two most common types of DM. Treatment for type 1 diabetes often consists of insulin replacement therapy, while treatment for type 2 diabetes typically consists of oral hypoglycemics.

OBJECTIVES

Conventional dosing schedules for the vast majority of these medications come with a number of drawbacks, the most common of which are frequent dosing, a short half-life, and low bioavailability. Thus, innovative and regulated oral hypoglycemic medication delivery methods have been developed to reduce the limitations of standard dose forms.

METHODS

The studies and reviews published under the title were looked up in several databases (including PubMed, Elsevier, and Google Scholar).

RESULTS

Hydrogels made from biopolymers are three-dimensional polymeric networks that can be physically or chemically crosslinked. These networks are based on natural polymers and have an inherent hydrophilic quality because of the functional groups they contain. They have a very high affinity for biological fluids in addition to a high water content, softness, flexibility, permeability, and biocompatibility. The fact that these features are similar to those of a wide variety of soft living tissues paves the way for several potentials in the field of biomedicine. In this sense, hydrogels offer excellent platforms for the transport of medications and the controlled release of those drugs. Additionally, biopolymer-based hydrogels can be put as coatings on medical implants in order to improve the biocompatibility of the implants and to prevent medical diseases.

CONCLUSION

The current review focuses on the most recent advancements made in the field of using biopolymeric hydrogels that are physically and chemically crosslinked, in addition to hydrogel coatings, for the purpose of providing sustained drug release of oral hypoglycemics and avoiding problems that are associated with the traditional dosage forms of oral hypoglycemics.

Advances in chitosan-based hydrogels for pharmaceutical and biomedical applications: A comprehensive review

The treatment of diseases, such as cancer, is one of the most significant issues correlated with human beings health. Hydrogels (HGs) prepared from biocompatible and biodegradable materials, especially biopolymers, have been effectively employed for the sort of pharmaceutical and biomedical applications, including drug delivery systems, biosensors, and tissue engineering. Chitosan (CS), one of the most abundant bio-polysaccharide derived from chitin, is an efficient biomaterial in the prognosis, diagnosis, and treatment of diseases. CS-based HGs possess some potential advantages, like high values of bioactive encapsulation, efficient drug delivery to a target site, sustained drug release, good biocompatibility and biodegradability, high serum stability, non-immunogenicity, etc., which made them practical and useful for pharmaceutical and biomedical applications. In this review, we summarize recent achievements and advances associated with CS-based HGs for drug delivery, regenerative medicine, disease detection and therapy.

Hydrogels Based on Natural Polymers Loaded with Bentonite and/or Halloysite: Composition Impact on Spectroscopic, Thermal, and Swelling Properties

Hydrogels are characterized by their property of absorbing and releasing a high content of water and water-based liquids; thus, they can be applied in agriculture as controlled-release water and fertilizer products. The focus of this research was efficient and low-cost natural polymer-based hydrogels obtained by crosslinking gellan gum (GGLA) and starch (ST) with acetic acid (CA) and loading them with either bentonite (BET) and/or halloysite (HAL). The hydrogels were obtained by mixing 100, 75, 50, 25, and 0 wt.% of GGLA with 0, 25, 50, 75, and 100 wt.% ST water solutions. To obtain the networks, they were crosslinked with 10, 5, and 2 wt.% of CA and loaded with 2, 5, and 10 wt.% of BET and/or HAL. The samples were analyzed by infrared spectroscopy (FTIR), differential scanning calorimetry (DSC), their swelling in water, and the state of bound water properties. The results of these analyses point to the formation of a polymeric network with a decomposition temperature of >250 °C, and tailorable swelling properties that vary between 3 and 77, depending on the hydrogel composition. In summary, GGLA-ST-BET/HAL hydrogels are a good option for eco-friendly agriculture materials.

Lignin Modification for Enhanced Performance of Polymer Composites

The biopolymer lignin, which is heterogeneous and abundant, is usually present in plant cell walls and gives them rigidity and strength. As a byproduct of the wood, paper, and pulp manufacturing industry, lignin ranks as the second most prevalent biopolymer worldwide, following cellulose. This review paper explores the extraction, modification, and prospective applications of lignin in various industries, including the enhancement of thermosetting and thermoplastic polymers, biomedical applications such as vanillin production, fuel development, carbon fiber composites, and the creation of nanomaterials for food packaging and drug delivery. The structural characteristics of lignin remain undefined due to its origin, separation, and fragmentation processes. This comprehensive overview encompasses state-of-the-art techniques, potential applications, diverse extraction methods, chemical modifications, carbon fiber utilization, and the extraction of vanillin. Moreover, the review focuses on the utilization of lignin-modified polymer blends across multiple manufacturing sectors, providing insights into the advantages and limitations of this innovative approach for the development of environmentally friendly materials.

Recent advances in double network hydrogels based on naturally-derived polymers: synthesis, properties, and biological applications

Hydrogels composed of naturally-derived biopolymers have garnered significant research interest due to the bioavailability and biocompatibility of starting materials. However, translating these advantages to practical use is challenged by limitations of mechanical properties and stability of the resulting materials. The development of double network (DN) hydrogels has led to greatly enhanced mechanical properties and shows promise toward broadening the applications of conventional synthetic or natural hydrogels. This review highlights recently developed protein-based and polysaccharide-based DN hydrogels. For each biopolymer, we focus on a subset of DN hydrogels centered around a theme related to synthetic design or applications. Network structures and crosslinking mechanisms that endow enhanced mechanical properties and performance to the materials are discussed. Important applications, including tissue engineering, drug delivery, bioadhesives, wound healing, and wearable sensors, that arise from the inherent properties of the natural polymer or its combination with other materials are also emphasized. Finally, we discuss ongoing challenges to stimulate the discovery of new design principles for the future of DN hydrogels based on naturally-derived polymers for biological applications.

Polymeric Hydrogels for Intervertebral Disc Replacement/Integration: Playing with the Chemical Composition for Tuning Shear Behavior and Hydrophilicity

Damages to the intervertebral disc (IVD) due to improper loading or degeneration result in back pain, which is a common disease affecting an increasing number of patients. Different strategies for IVD remediation have been developed, from surgical treatment to disc replacement, by using both metallic and non-metallic materials. Hydrogels are very attractive materials due to their ability to simulate the properties of many soft tissues; moreover, their chemical composition can be varied in order to assure performances similar to the natural disc. In particular, for the replacement of the IVD outer ring, namely, the anulus fibrosus, the shear properties are of paramount importance. In this work, we produced hydrogels through the photo-induced crosslinking of different mixtures composed of two hydrophilic monofunctional and difunctional polymers, namely, poly(ethyleneglycol) methyl ether methacrylate (PEGMEMA) and poly(ethyleneglycol) dimethacrylate (PEGDMA), together with a hydrophobic molecule, i.e., tert-butyl acrylate (tBA). By changing the ratio among the precursors, we demonstrated the tunability of both the shear properties and hydrophilicity. The structural properties of hydrogels were studied by solid-state nuclear magnetic resonance (NMR). These experiments provided insights on both the structure and molecular dynamics of polymeric networks and, together with information obtained by differential scanning calorimetry (DSC), allowed for correlating the physical properties of the hydrogels with their chemical composition.

Fabrication of Chitosan/PEGDA Bionanocomposites for Enhanced Drug Encapsulation and Release Efficiency

Drug delivery systems (DDS) have evolved in the last decades with the development of hydrogels and particles. However, challenges such as high systemic uptake, side effects, low bioavailability, and encapsulation efficiency continue to be significant hurdles faced by such DDSs. Particles and hydrogels can be specifically designed for targeted DDSs to mitigate some of these problems. This study developed chitosan (Cs) particles (Ps) and composite films using poly(ethylene glycol) diacrylate (PEGDA) as a copolymer to encapsulate gentamicin (GtS) for drug delivery. We demonstrated that lysozyme degrades the chitosan β-1,4 glycosidic bonds to release GtS. PEGDA increased drug encapsulation efficiency by shielding the repelling forces of like charges between Cs and GtS. The data show that PEGDA does not hinder enzymatic degradation while increasing drug encapsulation efficiency and producing more homogeneous particles. Additionally, we utilized Michael's reaction to cross-link Cs, CsPs, and PEGDA to produce a film designed for drug delivery. The film is an anchor for CsPs to prevent premature drug release. The cross-linking of Cs and PEGDA does not affect lysozyme activity, and CsPs could successfully release GtS without affecting GtS activity.

Application of 3D- printed hydrogels in wound healing and regenerative medicine

Hydrogels are three-dimensional polymer networks with hydrophilic properties. The modifiable properties of hydrogels and the structure resembling living tissue allow their versatile application. Therefore, increasing attention is focused on the use of hydrogels as bioinks for three-dimensional (3D) printing in tissue engineering. Bioprinting involves the fabrication of complex structures from several types of materials, cells, and bioactive compounds. Stem cells (SC), such as mesenchymal stromal cells (MSCs) are frequently employed in 3D constructs. SCs have desirable biological properties such as the ability to differentiate into various types of tissue and high proliferative capacity. Encapsulating SCs in 3D hydrogel constructs enhances their reparative abilities and improves the likelihood of reaching target tissues. In addition, created constructs can simulate the tissue environment and mimic biological signals. Importantly, the immunogenicity of scaffolds is minimized through the use of patient-specific cells and the biocompatibility and biodegradability of the employed biopolymers. Regenerative medicine is taking advantage of the aforementioned capabilities in regenerating various tissues- muscle, bones, nerves, heart, skin, and cartilage.

Dissolving and Swelling Hydrogel-Based Microneedles: An Overview of Their Materials, Fabrication, Characterization Methods, and Challenges

Polymeric hydrogels are a complex class of materials with one common feature-the ability to form three-dimensional networks capable of imbibing large amounts of water or biological fluids without being dissolved, acting as self-sustained containers for various purposes, including pharmaceutical and biomedical applications. Transdermal pharmaceutical microneedles are a pain-free drug delivery system that continues on the path to widespread adoption-regulatory guidelines are on the horizon, and investments in the field continue to grow annually. Recently, hydrogels have generated interest in the field of transdermal microneedles due to their tunable properties, allowing them to be exploited as delivery systems and extraction tools. As hydrogel microneedles are a new emerging technology, their fabrication faces various challenges that must be resolved for them to redeem themselves as a viable pharmaceutical option. This article discusses hydrogel microneedles from a material perspective, regardless of their mechanism of action. It cites the recent advances in their formulation, presents relevant fabrication and characterization methods, and discusses manufacturing and regulatory challenges facing these emerging technologies before their approval.

A Bioinspired Self-Healing Conductive Hydrogel Promoting Peripheral Nerve Regeneration

The development of self-healing conductive hydrogels is critical in electroactive nerve tissue engineering. Typical conductive materials such as polypyrrole (PPy) are commonly used to fabricate artificial nerve conduits. Moreover, the field of tissue engineering has advanced toward the use of products such as hyaluronic acid (HA) hydrogels. Although HA-modified PPy films are prepared for various biological applications, the cell-matrix interaction mechanisms remain poorly understood; furthermore, there are no reports on HA-modified PPy-injectable self-healing hydrogels for peripheral nerve repair. Therefore, in this study, a self-healing electroconductive hydrogel (HASPy) from HA, cystamine (Cys), and pyrrole-1-propionic acid (Py-COOH), with injectability, biodegradability, biocompatibility, and nerve-regenerative capacity is constructed. The hydrogel directly targets interleukin 17 receptor A (IL-17RA) and promotes the expression of genes and proteins relevant to Schwann cell myelination mainly by activating the interleukin 17 (IL-17) signaling pathway. The hydrogel is injected directly into the rat sciatic nerve-crush injury sites to investigate its capacity for nerve regeneration in vivo and is found to promote functional recovery and remyelination. This study may help in understanding the mechanism of cell-matrix interactions and provide new insights into the potential use of HASPy hydrogel as an advanced scaffold for neural regeneration.

Resorbable Membranes for Guided Bone Regeneration: Critical Features, Potentials, and Limitations

Lack of horizontal and vertical bone at the site of an implant can lead to significant clinical problems that need to be addressed before implant treatment can take place. Guided bone regeneration (GBR) is a commonly used surgical procedure that employs a barrier membrane to encourage the growth of new bone tissue in areas where bone has been lost due to injury or disease. It is a promising approach to achieve desired repair in bone tissue and is widely accepted and used in approximately 40% of patients with bone defects. In this Review, we provide a comprehensive examination of recent advances in resorbable membranes for GBR including natural materials such as chitosan, collagen, silk fibroin, along with synthetic materials such as polyglycolic acid (PGA), polycaprolactone (PCL), polyethylene glycol (PEG), and their copolymers. In addition, the properties of these materials including foreign body reaction, mechanical stability, antibacterial property, and growth factor delivery performance will be compared and discussed. Finally, future directions for resorbable membrane development and potential clinical applications will be highlighted.