Copper nanoclusters @ nitrogen-doped carbon quantum dots-based ratiometric fluorescence probe for lead (II) ions detection in porphyra

A ratiometric fluorescent dark box and smartphone integrated portable sensing platform based on hydrogen bonding induction for on-site determination of enrofloxacin

Enrofloxacin (ENR) residues in animal-derived food and water threaten human health. Simple, low-cost and on-site detection methods are urgently needed. Blue emitting carbon quantum dots (CQDs) and orange rhodamine B (RhB) were used as recognition and reference signals, respectively, to construct a ratiometric fluorescence sensor. After the addition of ENR, the color of the sensor changed from orange to blue because hydrogen bonding induced a considerable increase in CQDs fluorescence. Based on this mechanism, a simple and low cost on-site portable sensing platform was constructed, which integrated a stable UV light strip and a smartphone with voice-controlled phototaking function and an RGB app. The t-test results of spiked ENR recoveries for diluted milk, honey and drinking water revealed no significant differences between the ratiometric fluorescent sensor and portable sensing platform. Thus, this portable sensing platform provides a novel strategy for on-site quantification of quinolone antibiotics in foodstuffs and environmental water.

A highly selective dual-signal response ratiometric fluorescence sensing strategy for malachite green in fish based on carbon dots/copper nanoclusters nanocomposite

Malachite green (MG), a widely used antiparasitic agent, poses health risks to human due to its genotoxic and carcinogenic properties. Herein, a stable dual-emission fluoroprobe of carbon dots/copper nanoclusters is prepared for highly selective detection of MG based on the inner filter effect. This probe exhibits characteristic emission bands at 435 and 625 nm when excited at 376 nm. After adding MG, the both emission signals were significantly quenched, and the ratio of fluorescence intensity (F435/F625) was linearly related to the concentration of MG in the range of 0.05-40 μmol L-1 with a limit of detection of 18.2 nmol L-1. Meanwhile, the two signals exhibit linear relationships with the concentration of MG, respectively, and the corresponding detection results were consistent. The fluoroprobe was successfully used for the detection of MG in fish samples with the recoveries ranging from 96.0% to 103.8% and a relative standard deviation of <3.3%.

Dual-emission carbon dots for ratiometric fluorescence sensing of thiabendazole in fruits

Quantitative determination of pesticides in fruits and vegetables is essential for human healths. Herein, a new dual-emission carbon dots with high fluorescence stability at a pH range of 4-10 and a temperature range of 0-60 °C was synthesized. And a novel ratiometric fluorescence probe was proposed to detect thiabendazole (TBZ) residue with a wide linear range (0-1000 μM) and low detection limit (0.15 μM). The emission at 512 nm exhibited a special "turn-off" fluorescence sensing of TBZ due to internal filter effect, while that at 361 nm barely changed and worked as reference. Furthermore, the ratiometric fluorescence strategy was successfully applied for determining TBZ in fruits with good recoveries (96.73%-111.17 %, 93.29%-120.78 % and 96.28%-100.57 %, respectively). Notably, the constructed ratiometric fluorescence probe had comparable accuracy to HPLC in detecting unknown concentrations of TBZ in pear juice, demonstrating dual-emission carbon dots possess wide and promising applicability for fluorescence sensing pesticides in the future.

Nanotechnology-based analytical techniques for the detection of contaminants in aquatic products

Food safety of aquatic products has attracted considerable attention worldwide. Although a series of conventional bioassays and instrumental methods have been developed for the detection of pathogenic bacteria, heavy metal residues, marine toxins, and biogenic amines during the production and storage of fish, shrimp, crabs et al., the nanotechnology-based analyses still have their advantages and are promising since they are cost-efficient, highly sensitive and selective, easy to conduct, facial design, often require no sophisticated instruments but with excellent detection performance. This review aims to summarize the advances of various biosensing strategies for bacteria, metal ions, and small molecule contaminants in aquatic products during the last five years, The review highlights the development in nanotechnologies applied for biorecognition process, signal transduction and amplification methods in each novel approach, the nuclease-mediated DNA amplification, nanomaterials (noble metal nanoparticle, metal-organic frameworks, carbon dots), lateral flow-based biosensor, surface-enhanced Raman scattering, microfluidic chip, and molecular imprinting technologies were especially emphasized. Moreover, this study provides a view of current accomplishments, challenges, and future development directions of nanotechnology in aquatic product safety evaluation.

A novel sustainable biomass-based fluorescent probe for sensitive detection of salicylic acid in rice

Herein, a ratiometric fluorescent probe was developed for sensitive detection of salicylic acid (SA) in rice using silk-derived carbon quantum dots @ Curcumin @ iron-based metal organic framework (SCQDs@Cur@Fe-MOFs). Fe-MOFs with porous structure not only provided holes for SCQDs to evade self-aggregation of SCQDs, but Fe2+ ions from MOFs was ingeniously employed to capture active sites of Cur, solving the problem of lacking sufficient specificity of Cur to SA while converting weak response signal to amplified "turn on" mode. Upon exposed to SA, the probe interacted with SA to form Cur-Fe2+-SA ternary complex, which inhibited the internal filtration effect between Cur and SCQDs, and triggered a cascade of response signaling. With this strategy, the proposed probe achieved sensitive determination of salicylic acid in rice with detection limit as low as 0.14 μmol/L. This study provides unique insight into constructing economical and eco-friendly fluorescent sensor for SA detection with superior performance.

A dual-emitting fluoroprobe fabricated by aloe leaf-based N-doped carbon quantum dots and copper nanoclusters for nitenpyram detection in waters by virtue of inner filter effect and static quenching principles

Fluorescence sensing technique has been used in environmental analysis due to its simplicity, low cost, and visualization. Although the fruit pulp-based biomass carbon quantum dots (CQDs) have excellent luminescent properties, aloe leaves possess the superiority of being easily accessible in all seasons compared to fruit pulp. Thus, we fabricated Aloe carazo leaf-based nitrogen doping-CQDs (N-CQDs) using a facile hydrothermal approach, which emitted bright blue fluorescence with a quantum yield of 21.4 %. By comparison, the glutathione-encapsulated copper nanoclusters (GSH-CuNCs) displayed strong red fluorescence. A blue/red dual emission based on the N-CQDs/CuNCs mixture was established for nitenpyram detection. At the 350-nm excitation, the N-CQD/CuNCs system produced dual-wavelength emitting peaks at 440 and 660 nm, respectively. Moreover, when nitenpyram was introduced into the system, the fluorescence intensities (FIs) of N-CQDs significantly decreased, whereas the FIs of GSH-CuNCs varied slightly; simultaneously, the solution color changed from bright blue to dark red. Both the spectral overlapping between nitenpyram's UV-Vis absorption and N-CQDs' excitation and almost unchanged fluorescence lifetimes indicated the occurrence of inner-filtering effect (IFE) in the dual-emitting fluoroprobe. In addition, the Stern-Volmer constant (Ksv = 6.92 × 103 M-1), temperature effect, as well as UV-Vis absorption of N-CQD/CuNCs before and after the addition of nitenpyram corroborated the static-quenching behavior. Consequently, the fluorescence-quenching of N-CQDs by nitenpyram was attributable to the joint IFE and static-quenching principles. A good linearity existed between the F660/F440 values and nitenpyram concentrations (0.5-200 μM) with a method detection limit of 0.15 μM. The dual-emitting fluoroprobe provided the satisfactory recoveries (95.0%-107.0 %) for nitenpyram detection in real-world waters, which were comparable with the results of traditional liquid chromatography coupled to tandem mass spectrometry method. Owing to its simple operations, low-cost, and adaptability for on-site outdoor monitoring, the newly developed dual-emitting fluoroprobe possesses great potential applications in routine monitoring of nitenpyram under field conditions.

Morphology regulation of isomeric covalent organic frameworks for high selective light scattering detection of lead

Isomerism is an essential and ubiquitous phenomenon in organic chemistry, yet it is rarely observed in covalent organic frameworks (COFs). Herein, we synthesized two framework-isomeric COFs (BATD-Dma-COF-K and BATD-Dma-COF-R) and found for the first time that the light scattering signal of the COFs can be used for the analytical detection of lead ion. By using solvothermal and room temperature solvent synthesis methods, controlling different synthesis conditions, and introducing regulators to increase the energy difference between different products, the product with the lowest energy could be synthesized under specific conditions. This method could control the morphology of the synthesized COF and realize the precise synthesis of framework-isomeric COF by changing the experimental conditions. The structures of the two framework-isomeric COFs were characterized and confirmed by a series of analytical methods. Based on the principle that lead ions coordinate with N and O on the surface of two skeletal isomers BATD-Dma-COFs to enhance the light scattering signal of the COFs, a light scattering probe was developed by BATD-Dma-COF for the detection of metal lead ion in water samples. Lead ion concentration in the range from 2.0 to 250.0 μM had a good linear relationship with the light scattering intensity increase of the COFs with detection limit as low as 0.8397 μM by BATD-Dma-COF-K and 0.9207 μM by BATD-Dma-COF-R.

Illuminating the path: aggregation-induced emission for food contaminants detection

Food safety is a global concern that deeply affects human health. To ensure the profitability of the food industry and consumer safety, there is an urgent need to develop rapid, sensitive, accurate, and cost-effective detection methods for food contaminants. Recently, the Aggregation-Induced Emission (AIE) has been successfully used to detect food contaminants. AIEgens, fluorescent dyes that cause AIE, have several valuable properties including high quantum yields, photostability, and large Stokes shifts. This review provides a detailed introduction to the principles and advantages of AIE-triggered detection, followed by a focus on the past five years' applications of AIE in detecting various food contaminants including pesticides, veterinary drugs, mycotoxins, food additives, ions, pathogens, and biogenic amines. Each detection principle and component is comprehensively covered and explained. Moreover, the similarities and differences among different types of food contaminants are summarized, aiming to inspire future researchers. Finally, this review concludes with a discussion of the prospects for incorporating AIEgens more effectively into the detection of food contaminants.

Efficient Adsorption and Electrochemical Detection of Cd2+ with a Ternary MgZnFe-Layered Double Hydroxides Engineered Porous Biochar Composite

Their unique layered structure, large specific surface area, good stability, high negative charge density between layers, and customizable composition give layered double hydroxides (LDHs) excellent adsorption and detection performance for heavy metal ions (HMIs). However, their easy aggregation and low electrical conductivity limit the practical application of untreated LDHs. In this work, a ternary MgZnFe-LDHs engineered porous biochar (MgZnFe-LDHs/PBC) heterojunction was proposed as a sensing and adsorption material for the effective detection and removal of Cd2+ from wastewater. The growth of MgZnFe-LDHs in the PBC pores not only reduces the accumulation of MgZnFe-LDHs, but also improves the electrical conductivity of the composite. The synergistic effect between MgZnFe-LDHs and PBC enables the composite to achieve a maximum adsorption capacity of up to 293.4 mg/g for Cd2+ in wastewater. Meanwhile, the MgZnFe-LDHs/PBC-based electrochemical sensor shows excellent detection performance for Cd2+, presenting a wide linear range (0.01 ng/L-1 mg/L), low detection limit (3.0 pg/L), good selectivity, and stability. The results indicate that MgZnFe-LDHs/PBC would be a potential material for detecting and removing Cd2+ from wastewater.

A portable test strip fabricated of luminescent lanthanide-functionalized metal-organic frameworks for rapid and visual detection of tetracycline antibiotics

Tetracycline antibiotics (TCs) are commonly used antibiotics in the treatment of infections, but their overuse has a negative impact on human health and ecosystems. Thus, the development of a facile and on-site visualization method for TC detection is necessary. Here, we propose the potential of using lanthanide-functionalized metal-organic framework (MOF) composites (Ag+/Tb3+@UiO-66-(COOH)2, ATUC) as a probe for the rapid detection of tetracycline (TC), chlortetracycline (CTC), oxytetracycline (OTC), and doxycycline (DOX) residues, in which UiO-66-(COOH)2 (UC) could be utilized to provide an interaction microenvironment, Tb3+ as recognition units and Ag+ as a fluorescence enhancer. Upon exposure to TCs, significant luminescence quenching of ATUC excited at 255 nm was observed due to the inner filter effect (IFE) and photo-induced electron transfer (PET), and the established strategy has a detection limit (LOD) of 11.0, 20.1, 9.1, and 22.5 nM for TC, CTC, OTC, and DOX, respectively. More importantly, given its portability and conspicuous luminescence color gradation variation, a portable test strip based on ATUC was manufactured and the results could be distinguished immediately by the naked eye and smartphone analysis, allowing for on-site rapid quantitative assay of TCs, not only in the laboratory but also in a point-of-care setting.

A dual-modal biosensor coupling cooperative catalysis strategy for sensitive detection of AFB1 in agri-products

Herein, the cooperative catalysis effect between nanocomposite (AgPd NPs/POD-M/PEI-rGO) and horseradish peroxidase (HRP) was applied for the fast and sensitive detection of aflatoxin B1 (AFB₁). Upon specific and competitive binding of HRP@DNA and AFB₁ to cDNA, the working electrode presented different catalytic capacities for supporting electrolytes (TMB and H₂O₂). In the redox mechanism of TMB and H₂O₂, HRP and nanocomposite effectively catalyzed the oxidization of TMB to form the one-electron oxidation intermediate TMB+, and contributed the electrical signals and absorbance signals. Electrochemistry and colorimetric analyses were successfully realized for AFB₁ detection with 0.2 pg/mL and 8 pg/mL of detection limits, respectively, which is much lower than that of traditional HPLC methods. Overall, this method had significant reliability and sensitivity, offering a promising potential for conveniently evaluating the quality of agri-products polluted with AFB₁. Moreover, this approach provides a new idea for fast and accurate detection of mycotoxin.

Advances in Fluorescent Sensing Carbon Dots: An Account of Food Analysis

Illuminating the use of nanomaterials, carbon quantum dots (CQDs) have transfigured the food safety arena because of their bright luminescence, optical properties, low toxicity, and enhanced biocompatibility. Therefore, fluorescent resonance energy transfer, photoinduced electron transfer, and an internal filtering effect mechanism allow precise detection of food additives, heavy metal ions, pathogenic bacteria, veterinary drug residues, and food nutrients. In this review, we describe the primal mechanism of CQD-based fluorescence sensors for food safety inspection. This is an abridged description of the nanodesign and future perspectives of more advanced CQD-based sensors for food safety analysis.

A novel ratiometric fluorescent probe for sensitive detection of jasmonic acid in crops

Herein, a novel ratiometric fluorescent probe was proposed for sensitive detection of jasmonic acid (JA) based on NCQDs@Co-MOFs@MIPs. The prepared NCQDs, with uniquely dual-emissive performance, are insensitive to JA due to electrostatic repulsion. Interestingly, the introduction of Co-MOFs not only avoided the self-aggregation of NCQDs, but changed the surface charge of NCQDs and triggered the response of NCQDs to JA. More importantly, the imprinted recognition sites from MIPs provided "key-lock" structures to specifically capture JA molecules, greatly improving the selectivity of the probe to JA. Under the synergistic actions of Co-MOFs and MIPs, JA can interact with NCQDs through photo-induced electron transfer (PET), resulting in the changes on emission intensity of the probe at E_m = 367 nm and 442 nm. Based on the observations, the quantification of JA was realized in the range of 1-800 ng/mL with the limit of detection (LOD) of 0.35 ng/mL. In addition, the probe was used for detecting JA in rice with satisfactory analysis results, indicating the probe holds great potential for monitoring JA levels in crops. Overall, this strategy provides new insights into the construction of practical probes for sensitive detection of plant hormones in crops.

A smart ratiometric fluoresence and colorimetry dual-responsive sensor for morin determination based on the complex between carbon quantum dots and polyethyleneimine

As a representative flavonoid, morin exhibits multi-biological activities, but its abuse endangers human health. Developing advanced technology for morin determination is urgently needed. In this study, a dual-responsive approach was reported for morin based on the complexing of carbon quantum dots (CQDs) and polyethyleneimine (PEI). The CQDs were fabricated via an improved hydrothermal method employing tyrosine and malic acid. Binding with PEI induced an 8-fold emission enhancement and a slight red-shift to 445 nm of CQDs because of the complexing of PEI and CQDs. Further morin introduction led to the blue emission (445 nm) quenching of CQDs-PEI and a yellow emission (560 nm) generation, which contributed a ratiometric fluorescence approach for morin determination between 2.0 and 32 μM, with a limit of detection (LOD) of 45 nM. Meanwhile, under sunlight the color of CQDs-PEI became yellow upon morin addition, which developed a colorimetric method for morin determination in a wide range between 2.0 and 100 μM (LOD = 69 nM). The developed dual-responsive method either displayed accurate results for morin in diluted human and bovine serum, being potential for actual sample analysis. Finally, a visual detection based on the smartphone was constructed and applied for the real-time determination of morin.

Nanozyme-catalysed CRISPR-Cas12a system for the preamplification-free colorimetric detection of lead ion

CRISPR-based detection was often based on the target preamplification to realize the high sensitivity. Here, we prepared a CRISPR-Cas12a system for the colorimetric detection of lead ion (Pb²⁺) based on the assistance of DNAzyme and nanozyme instead of preamplification. The recognition between GR-5 DNAzyme and Pb²⁺ could trigger the CRISPR-Cas12a system. MnO₂ nanozymes connected with magnetic beads through single stranded DNA were prepared as the colorimetric signal probes and catalyst of CRISPR-Cas12a system for the strong oxidase-like activity inducing the color change of 3,3',5,5'-tetramethylbenzidine. The nanozyme-catalysed CRISPR-Cas12a system could be used to detect Pb²⁺ through the color change with high specificity and sensitivity. The linear range of this approach was 0.8 nM-2500 nM, with a limit of detection of 0.54 nM. This method was applied for the detection of the Pb²⁺ in food samples indicating good accuracy and anti-interference ability.

Encapsulating gold nanoclusters into metal-organic frameworks to boost luminescence for sensitive detection of copper ions and organophosphorus pesticides

Gold nanoclusters (Au NCs) with luminescence property are emerging as promising candidates in fluorescent methods for monitoring contaminants, but low luminescence efficiency hampers their extensive applications. Herein, GSH-Au NCs@ZIF-8 was designed by encapsulating GSH-Au NCs with AIE effect into metal-organic frameworks, achieving high luminescence efficiency and good stability through the confinement effect of ZIF-8. Accordingly, a fluorescent sensing platform was constructed for the sensitive detection of copper ions (Cu²⁺) and organophosphorus pesticides (OPs). Firstly, the as-prepared GSH-Au NCs@ZIF-8 could strongly accumulate Cu²⁺ due to the adsorption property of MOFs, accompanied by a significant fluorescence quenching effect with a low detection limit of 0.016 μM for Cu²⁺. Besides, thiocholine (Tch), the hydrolysis product of acetylthiocholine (ATch) by acetylcholinesterase (AchE), could coordinate with Cu²⁺ by sulfhydryl groups (-SH), leading to a significant fluorescence recovery, which was further used for the quantification of OPs owing to its inhibition to AChE activity. Furthermore, a hydrogel sensor was explored to accomplish equipment-free, visual, and quantitative monitoring of Cu²⁺ and OPs by a smartphone sensing platform. Overall, this work provides an effective and universal strategy for enhancing the luminescence efficiency and stability of Au NCs, which would greatly promote their applications in contaminants monitoring.

Inner-filter Effect Induced Fluorescence Quenching of Carbon Dots for Cr(VI) Detection with High Sensitivity

Carbon dots (CDs) were used to develop a sensitive sensing technique for detecting Cr(VI). CDs were made using a hydrothermal technique from citric acid and glutamic acid. These prepared CDs emitted blue fluorescence under excitation of 350 nm (λ_em = 420 nm), and the fluorescence quantum yield was 48.41%. Transmission electron microscope was used to examine the morphology of the CDs, which had an average size of 2.21 ± 0.39 nm. The elementary composition and bonding structure of the CDs were conducted by XPS and FT-IR spectrum. Cr(VI) quenched the fluorescence of CDs through a static quenching effect and an inner filter effect, allowing Cr(VI) to be detected quantitatively. This approach was used to detect Cr(VI) in two samples of water, with the findings demonstrating that it is reliable and accurate. The fluorescence intensity change was linearly related to the concentration of Cr(VI) in the range from 0.5 to 400 μM, with the detection limit being 0.10 μM. This approach has the virtues of wide detection range, low cost and fast response. The strategy has a great application prospect for detecting Cr(VI) in practical samples.

Detection of Heavy Metal Ions by Ratiometric Photoelectric Sensor

In recent years, heavy metal pollution has become increasingly serious. Heavy metals exist in an environment mainly in the form of ions (heavy metal ions, HMs). They can contaminate food, water, soil, and the atmosphere, leading to serious harm to plants and animals. With high bioavailability and nonbiodegradability, HMs can accumulate through biomagnification. Consequently, heavy metal pollution has become the cause of many fatal diseases threatening human health and ecological environment. Therefore, the accurate detection of HMs is vital and necessary. In this paper, the harm and limit standards of heavy metals were systematically summarized and the common analysis methods were overviewed and compared. Specifically, the latest research progress of ratiometric photoelectric sensor, including optical and electrical sensor, were mainly described. The research status and advantages and disadvantages of a photoelectric sensor were summarized. Furthermore, the future directions were proposed, which provided the reference for the further research and application of the ratiometric photoelectric sensor.

Facile synthesis of dual-ligand terbium-organic gels as ratiometric fluorescence probes for efficient mercury detection

Mercury (Hg) pollution can negatively impact ecosystems, and there is a need for simple Hg²⁺ monitoring platforms. Here, a dual-ligand fluorescence probe based on terbium-organic gels (Tb-L_0.2P_0.8 MOGs) was constructed for efficient Hg²⁺ detection. Tb-L_0.2P_0.8 MOGs were developed through a facile room-temperature gelation method, showing two emission peaks derived from luminol and Tb³⁺ at 424 nm and 544 nm, respectively. The aggregation-induced emission (AIE) effect between luminol and Tb³⁺ led to luminol with blue fluorescence. However, Hg²⁺ could dramatically quench the fluorescence signal of luminol at 424 nm because of the intense coordination interaction of Hg²⁺ with luminol and photo-induced electron transfer (PET). The Phen ligand could sensitize the luminescence of Tb³⁺ and offer a reference fluorescence, thus resulting in a unique ratiometric fluorescence response toward Hg²⁺. This novel nanoprobe had excellent linearity with Hg²⁺ concentrations range of 0.1-30 μM; the detection limit was 3.6 nM. The analysis of real samples showed the potential application of MOGs for measuring Hg²⁺ in porphyra and tap water. Mixed ligands were introduced for high-efficiency strategies to improve the analytical performance by regulating the emission behavior of MOGs.

Hydrogen sulfide gas sensing toward on-site monitoring of chilled meat spoilage based on ratio-type fluorescent probe

In this study, a fluorescence sensing platform for visual detection of hydrogen sulfide (H₂S) based on ratiometric fluorescent substances was developed to real-time monitor meat spoilage. The copper nanoclusters (CuNCs) and nitrogen-doped carbon quantum dots (CNQDs) were used as dual emission fluorescence materials. The fluorescence ratio of the two wavelengths decreased in the sulphide concentration range of 0-3 μmolL(exp)^-1, with a detection limit of 62.7 nmolL(exp)^-1. In order to capture hydrogen sulfide gas in the air, the ratio fluorescent material is loaded on the paper base. By processing the RGB value of the photo under UV light, the detection limit of the sensor is 4.35 ppt in the range of 0 ∼ 45.2 ppt H₂S gas concentration. This portable visual analysis greatly simplifies the steps of H₂S gas detection while ensuring sensor stability and sensitivity. It also provides a new method for H₂S detection during the meat storage process.

A FRET Fluorescent Sensor for Ratiometric and Visual Detection of Sulfide Based on Carbon Dots and Silver Nanoclusters

In this work, the fluorescent sensor based on fluorescence resonance energy transfer (FRET) and electrostatic interaction (EI) was prepared for the ratiometric and visual detecting S^2-. The FRET fluorescent sensor consists of two fluorophores, with carbon dots (CDs) as energy donors and silver nanoclusters (Ag NCs) as acceptors. At 390 nm excitation, CDs and Ag NCs showed two well-separated peaks at 445 nm and 660 nm, separately. The existence of S^2- caused the red fluorescence at 660 nm to be quenched, whereas the blue fluorescence at 445 nm was restored, and the fluorescence color of the ratiometric sensor changed from pink to blue. It could be employed in ratiometric and visual detecting S^2-. The linear range of quantitative detection S^2- was 0.5-100 μM, and its detection limit was 0.35 μM. CDs-Ag NCs could be used for detecting S^2- in mineral water and tap water. The results showed that the FRET ratiometric fluorescent sensor exhibits good anti-interference and high selectivity for detecting S^2- in environmental water samples.

Ultra-sensitive detection of hydrogen peroxide and levofloxacin using a dual-functional fluorescent probe

Herein, a flower-shaped fluorescent probe was proposed for hydrogen peroxide (H₂O₂) and levofloxacin (LVF) sensing based on MoOx QDs@Co/Zn-MOFs with porous structure. Both MoOx QDs and Co/Zn-MOFs exhibited peroxidase-like properties, and the combination of them greatly aroused the synergistic catalytic capabilities between them. In o-Phenylenediamine (OPD)-H₂O₂ system, MoOx QDs@Co/Zn-MOFs efficiently catalyzed H₂O₂ to produce •OH and then oxidized OPD to its oxidation product (OxOPD). The OxOPD could not only emit blue fluorescence, but also inhibit the fluorescent intensity of MoOx QDs through fluorescence resonance energy transfer (FRET). Moreover, when introducing LVF into the system, the fluorescent intensities of MoOx QDs increased along with the aggregation of themselves while that of OxOPD remained unchanged, which was explained by the joint behavior of FRET and photo-induced electron transfer (PET) instead of the conventional aggregation-induced emission enhancement (AIEE). With these observation, the proposed probe was employed for H₂O₂ and LVF determination in biological samples with the limit of detection (LOD) of 32.60 pmol/L and 0.85 μmol/L, respectively, suggesting the method holds great promises for trace H₂O₂ and LVF monitoring in eco-environment.

Combining metal nanoclusters and carbon nanomaterials: Opportunities and challenges in advanced nanohybrids

The development of functional materials with uniquely advanced properties lies at the core of nanoscience and nanotechnology. From the myriad possible combinations of organic and/or inorganic blocks, hybrids combining metal nanoclusters and carbon nanomaterials have emerged as highly attractive colloidal materials for imaging, sensing (optical and electrochemical) and catalysis, among other applications. While the metal nanoclusters provide extraordinary luminescent and electronic properties, the carbon nanomaterials (of zero, one or two dimensions) convey versatility, as well as unique interfacial, electronic, thermal, optical, and mechanical properties, which altogether can be put to use for the desired application. Herein, we present an overview of the field, for experts and non-experts, encompassing the basic properties of the building blocks, a systematic view of the chemical preparation routes and physicochemical properties of the hybrids, and a critical analysis of their ongoing and emerging applications. Challenges and opportunities, including directions towards green chemistry approaches, are also discussed.

Dual-emission fluorescent nanoprobe based on Ag nanoclusters for sensitive detection of Cu(II)

Noble metal nanoclusters have attracted much attention because of their excellent fluorescence properties. In this work, we demonstrated a dual-emission fluorescent nanocomposite based on silver nanoclusters. First, we synthesized positively charged His-AgNCs, which emits intense blue light, and then Ag nanoclusters with stable red emission were synthesized using DHLA as the ligand. Thus a dual-emission fluorescent nanoprobe was successfully obtained through electrostatic self-assembly, with the advantages of good water solubility and excellent stability. Based on the intensity ratio of the two emission peaks, the nanoprobe can be used for selective and sensitive detection of copper ions, and presents a good linear relationship within a certain concentration range. In addition, we also designed a polymer film, and our dual-emission nanoprobe was successfully loaded onto it, which means that the visual detection of copper ions is possible. This indicates that our dual-emission fluorescent nanoprobe has potential application prospects in environmental analysis, medical diagnosis, biological detection, etc.

An ultra-high-sensitivity electrochemiluminescence aptasensor for Pb2+ detection based on the synergistic signal-amplification strategy of quencher abscission and G-quadruplex generation

Signal amplification provides an effective way to improve detection performance. Herein, an ultrasensitive electrochemiluminescence (ECL) aptasensor for Pb²⁺ detection was developed based on a dual signal-amplification strategy of the abscission of a quencher and the generation of a G-quadruplex by one-step and simultaneous way. Nitrogen-doped carbon quantum dots linked with complementary DNA (cDNA-NCQDs) at the sensing interface was applied as the quencher of a tris(4,4'-dicarboxylic acid-2,2'-bipyridyl)ruthenium(II) (Ru(dcbpy)₃²⁺)/tripropylamine system to minimize the ECL signal due to the intermolecular hydrogen bond-induced energy-transfer process. Upon the addition of Pb²⁺, its specific binding with the aptamer triggered the abscission of cDNA-NCQDs, accompanied by the formation of G-quadruplex on the surface of the electrode, both of which amplified the intensity of the light emission. The ECL amplification efficiency induced by the above two mechanisms (78.6%) was valuably greater than that of their sum value (69.3%). This synergistic effect resulted in high detection sensitivity of the ECL aptasensor, which allowed to thereby obtain Pb²⁺ measurements in the range of 1 fM - 10 nM with an ultra-low detection limit of 0.19 fM. The Pb²⁺-mediated synergistic signal-amplification ECL strategy can provide a new approach for integrating various amplification strategies.

Highly Stable Copper Nano Cluster on Nitrogen-Doped Graphene Quantum Dots for the Simultaneous Electrochemical Sensing of Dopamine, Serotonin, and Nicotine; a Possible Addiction Scrutinizing Strategy

A highly stable copper nanocluster CuNC@N-GQD which exhibited stability for more than one year was synthesized using nitrogen doped graphene quantum dots (N-GQDs) as reducing and capping agents and smaller...

Synthesis of Copper Nanocluster and Its Application in Pollutant Analysis

Copper nanoclusters (Cu NCs) with their inherent optical and chemical advantages have gained increasing attention as a kind of novel material that possesses great potential, primarily in the use of contaminants sensing and bio-imaging. With a focus on environmental safety, this article comprehensively reviews the recent advances of Cu NCs in the application of various contaminants, including pesticide residues, heavy metal ions, sulfide ions and nitroaromatics. The common preparation methods and sensing mechanisms are summarized. The typical high-quality sensing probes based on Cu NCs towards various target contaminants are presented; additionally, the challenges and future perspectives in the development and application of Cu NCs in monitoring and analyzing environmental pollutants are discussed.

A Lab-in-a-Syringe Device Integrated with a Smartphone Platform: Colorimetric and Fluorescent Dual-Mode Signals for On-Site Detection of Organophosphorus Pesticides

Herein, a portable lab-in-a-syringe device integrated with a smartphone sensing platform was designed for rapid, visual quantitative determination of organophosphorus pesticides (OPs) via colorimetric and fluorescent signals. The device was chiefly made up of a conjugate pad labeled with cetyltrimethylammonium bromide-coated gold nanoparticles (CTAB-Au NPs) and a sensing pad modified by ratiometric probes (red-emission quantum dots@SiO₂ nanoparticles@green-emission quantum dots, rQDs@SiO₂@gQDs probe), which was assembled through a disposable syringe and reusable plastic filter. In the detection system, thiocholine (Tch), the hydrolysis product of thioacetylcholine (ATch) by acetylcholinesterase (AchE), could trigger the aggregation of CTAB-Au NPs, resulting in a significant color change from red to purple. Then, CTAB-Au NPs flowed vertically upward and bound to the rQDs@SiO₂@gQDs probe on the sensing pad, reducing the fluorescence resonance energy transfer effect between CTAB-Au NPs and gQDs. Meanwhile, rQDs embedded in SiO₂ NPs remained stable as internal reference fluorescence, achieving a color transition from red to green. Thus, based on the inhibition of AChE activity by OPs, a colorimetric and fluorescent dual-mode platform was constructed for on-site detection of OPs. Using glyphosate as a model, with the support of a color recognizer application (APP) on a smartphone, the ratio of red and green channel values could be utilized for accurate OP quantitative analysis ranging from 0 to 10 μM with a detection limit of 2.81 nM (recoveries, 90.8-122.4%; CV, 1.2-3.4%). Overall, the portable lab-in-a-syringe device based on a smartphone sensing platform integrated sample monitoring and result analysis in the field, implying great potential for on-site detection of OPs.

Copper nanocluster composites for analytical (bio)-sensing and imaging: a review

As an ideal substitute for traditional organic fluorescent dyes or up-conversion nanomaterials, copper nanoclusters (CuNCs) have developed rapidly and have been involved in exciting achievements in versatile applications. The emergence of novel CuNCs composites improves the poor stability and fluorescence intensity of CuNCs. With this in mind, great efforts have been made to develop a wide variety of CuNCs composites, and impressive progress has been made in the past few years. In this review, we systematically summarize absorption, fluorescence, electrochemiluminescence, and catalytic properties and focus on the multiple factors that affect the fluorescence properties of CuNCs. The fluorescence properties of CuNCs are discussed from the point of view of core size, surface ligands, self-assembly, metal defects, pH, solvent, ions, metal doping, and confinement effect. Especially, we illustrate the research progress and representative applications of CuNCs composites in bio-related fields, which have received considerable interests in the past years. Additionally, the sensing mechanism of CuNCs composites is highlighted. Finally, we summarize current challenges and look forward to the future development of CuNCs composites. Schematic diagram of the categories, possible sensing mechanisms, and bio-related applications of copper nanoclusters composites.

Engineering of an Upconversion Luminescence Sensing Platform Based on the Competition Effect for Mercury-Ion Monitoring in Green Tea

Accurately monitoring mercury ions (Hg²⁺) in food and agriculture-related matrixes (e.g., green tea) is of great significance to safeguard food safety. Here, we employed upconversion nanoparticles (UCNPs) and gold nanoparticles (AuNPs) to engineer a cysteine (Cys)-assisted anti-Stokes luminescence sensing platform (UCNPs-AuNPs) for precisely detecting residual Hg²⁺ in green tea through the competition effect. Initially, AuNPs could effectively quench the luminescence of UCNPs through the luminescence resonance energy transfer process, which was then interrupted by Cys-triggered AuNP aggregation via Au-S, thereby restoring UCNP luminescence. Interestingly, owing to the competition effect with AuNPs toward Cys, Hg²⁺ could weaken the luminescence restoring efficiency, achieving a Hg²⁺ concentration-dependent luminescence change. On this basis, a facile, reliable, and sensitive upconversion luminescence sensing platform for monitoring residual Hg²⁺ in green tea was successfully established. This study offers a novel insight into integrating the competition effect and anti-Stokes luminescence for food- and agriculture-related contaminant monitoring.

Sensing and bioimaging of lead ions in intracellular cancer cells and biomedical media using amine-functionalized silicon quantum dots fluorescent probe

A novel amine-functionalized silica quantum dots (SiQDs) fluorescent nanoprobe was developed for sensing of lead concentration in water, plasma and cell lysate. In addition, the developed probe was utilized for bioimaging of intracellular lead ions in HT 29 cancer cells. The amine-functionalized nanoprobe exhibited fluorescence emission at 445 nm under excitation at 355 nm. Upon addition of lead ions, the fluorescence of SiQDs linearly enhanced from 50 ng/mL to 5 µg/mL and 50 ng/mL to 25 µg/mL for plasma and standard media, respectively. The synthesis and fabrication of this probe are simple and serves high sensitivity with a limit of detection down to around 20 ng/mL. In the presence of various molecular and ion interfering, reliable results are obtained, confirming the specificity of the nanoprobe for lead ion detection. Meanwhile, amine-functionalized SiQD-based nanoprobe exhibits excellent cell membrane-permeability and biocompatibility. Thus, this probe is utilized for lead tracing in HT 29 cancer live cells. Fluorescent microscopy results confirmed the attachment of the produced nanomaterials to the HT 29 cancer cells.

Ratiometric sensing of Zn2+ with a new benzothiazole-based fluorescent sensor and living cell imaging

A new fluorescent probe, 3-(benzo[d]thiazol-2-yl)-5-bromosalicylaldehyde-⁴N-phenyl thiosemicarbazone (BTT), for ratiometric sensing of Zn²⁺ ions in methanol/HEPES buffer solution (3 : 2, pH = 7.4) is reported in this paper. The presence of Zn²⁺ ions yields a significant blue shift in the maximum emission of BTT from 570 nm to 488 nm, accompanied by a clear color change from orange to green. This emission change of BTT upon binding to Zn²⁺ in a 1 : 1 ratio may be due to the block of excited state intramolecular proton transfer (ESIPT) as well as chelation enhanced fluorescence (CHEF) on complex formation. The limit of detection (LOD) determined for Zn²⁺ quantitation was down to 37.7 nM. In addition, the probe BTT displays the ability to image both exogenous Zn²⁺ ions loaded into HeLa cells and endogenous Zn²⁺ distribution in living SH-SY5Y neuroblastoma cells.

A smartphone-integrated ratiometric fluorescence sensor for visual detection of cadmium ions

A novel fluorescence sensing platform was fabricated for visual detection of cadmium ions (Cd²⁺) with excellent stability and portability. In this protocol, dual-emission ratiometric fluorescence probe were constructed based on silicon oxide-coated copper nanoclusters (CuNCs@SiO₂) as a signal reference and cadmium telluride quantum dots (CdTe QDs) as signal response, thereby greatly improving the accuracy of test results. The level of Cd²⁺ can be reported within a wide linear range from 0.010 mg·L^-1 to 2.0 mg·L^-1 with a sensitive detection limit of 1.1 μg·L^-1 (2.75 μg·kg^-1) and a quick sample-to-answer monitoring time of 6 min, which was quite qualified for regularly monitoring Cd²⁺. Moreover, aiming to attain portable analysis, the smartphone as colorimetric reader and analyzer were also utilized for rapidly analyzing Cd²⁺ by capturing the change in fluorescence color. Additionally, benefiting from the strong combination of 1, 10-phenanthroline (Phen) and Cd²⁺, the fluorescence probe showed excellent anti-interference activities for Cd²⁺ assay in complex oyster matrix. Overall, the sensing platform had significant stability, specificity and sensitivity, offering a promising potential for conveniently evaluating the quality of marine bivalves polluted with Cd²⁺.

Rapid detection of cadmium ions in meat by a multi-walled carbon nanotubes enhanced metal-organic framework modified electrochemical sensor

This work presents an electrochemical device based on a composite modification of amine functionalized Zr(IV) metal-organic framework (UiO-66-NH2) and multi-walled carbon nanotubes (MWCNTs) for voltammetry determination of cadmium ions (Cd2+). The UiO-66-NH2@MWCNTs composites were prepared by one-pot hydrothermal reaction. The prepared sensor performs excellent performance, which was attributed to the synergism between UiO-66-NH2 with a special octahedral structure and enlarged surface area and MWCNTs with outstanding conductivity. Under optimal experiment condition, the fabricated sensor showed good linear relationship from 0.5 to 170 μg/L, with a detection limit of 0.2 μg/L. Finally, the sensor was successfully applied to detect Cd2+ in meat samples (N = 21) with relative standard deviation (RSD) lower than 4.5% and recovery of 95.1-107.5%, and the results were compared with certified method, there was no statistical significance difference between the developed sensor and certified method at a 95% confidence level.

Interaction between the functionalized probes: The depressed efficiency of dual-amplification strategy on ratiometric electrochemical aptasensor for aflatoxin B1

Signal amplification is one of the most effective ways to develop the high-performance electrochemical sensors. However, it can be more complicated for ratiometric detections. Herein, a ratiometric electrochemical aptasensor for aflatoxin B1 (AFB1) was proposed by taking advantage of a dual-amplification strategy by coupling of DNA walker (DW) with hybridization chain reaction (HCR). The special binding of AFB1 with ferrocene (Fc)-labelled aptamer triggers DW on hairpin DNA (hDNA) tracks to produce abundant double-stranded DNA (dsDNA). HCR-based strand amplification occurs on these dsDNA to absorb more methylene blue (MB). Then current ratio of MB (I_MB) and Fc (I_Fc) is designed as a yardstick to detect AFB1. Our experiments reveal that the interaction between Fc and MB (i.e., steric hindrance, electron mediator) varies. In addition to steric hindrance, the presence of MB also acts as electron mediator, thereby facilitating the electron transfer between Fc and electrode. Such combined effect consequently depresses the efficiency of dual-amplification strategy to improve the detection. The developed ratiometric electrochemical aptasensor allows the accurate detection of AFB1 in the 0.003-3 pg mL^-1 range. Our work has shed light on the amplification strategy for ratiometric sensing, and provided a new route in integrating different amplification strategies.

A multiple acetal chalcone-BODIPY-based fluorescence: synthesis, physical property, and biological studies

Fluorescent probes with outstanding physical and biological properties are superior for functional fluorescent dyes design. However, few studies pay attention to the stability of specific groups in fluorescent probes. The aldehyde group in the fluorescent probe is highly active but unstable under certain conditions. Therefore, we introduced ethoxy groups to realize the conversion to aldehyde groups under acidic conditions and avoid the instability of straightforward aldehyde groups. In this work, two fluorophores based on the multi acetal difluoroboraindacene (BODIPY) units with combination of the pharmaceutical intermediate chalcone have been firstly developed. In the design part, chalcone was introduced as a medium for fluorophore and multiple acetal. The mild synthesis strategy is based on the ligand ((Z)-2-chloro-1-(difluoroboranyl)-5-((4-ethyl-3,5-dimethyl-2H-pyrrol-2-ylidene)(phenyl)methyl)-1H-pyrrole) and connects with chalcone in (2E,2'E)-3,3'-(1,3-phenylene)bis(1-(2,4-bis(2,2-diethoxyethoxy)phenyl)prop-2-en-1-one). The emission wavelengths of the products are around 530 nm with high fluorescence intensity. To highlight the biological characteristics of these novel BODIPY fluorescents, we further demonstrated biological analysis studies on MTT and flow cytometry assays. The IC₅₀ values of BODIPY 5 ranged from 79 ± 6.11 to 63 ± 5.67 μM and BODIPY 6 were found to be 86 ± 4.07 to 58 ± 10.51 μM in tested cell lines. Flow cytometry data analysis shows that the representative agent 6 and reference have similar rational apoptosis rates in first quadrant. Last but not least, 6 shows outstanding biological compatibility and cell imaging potential in live cell imaging and in vivo assay, not only is the fluorescence prominent enough, but also rapidly distributes. Thus, our study reports a mild synthesis strategy and full biological analysis on BODIPY fluorescents, and the subtle modulation of the physical and biological properties by pharmaceutical substituents makes these designed chalcone-BODIPY-based dyes hopeful to realize drug functional fluorescent dyes. Two new highly sensitive BODIPY fluorophores are synthesized based on the ligand ((Z)-2-chloro-1-(difluoroboranyl)-5-((4-ethyl-3,5-dimethyl-2H-pyrrol-2-ylidene)(phenyl)methyl)-1H-pyrrole), which connects with chalcone in (2E,2'E)-3,3'-(1,3/4-phenylene)bis(1-(2,4-bis(2,2-diethoxyethoxy)phenyl)prop-2-en-1-one). Multiple acetals were introduced and the physical and biological properties of BODIPYs are described with MTT assay and in vitro and in vivo imaging.

Synthesis of biological quantum dots based on single-strand DNA and its application in melamine detection

By taking TC base-rich single-stranded DNA (ssDNA) as the raw material, a fluorescent biological quantum dots (Bio-dots) probe was prepared in one step through hydrothermal method, where its lifetime was greatly extended in comparison with Carbon quantum dots (CQDs), reaching 10.7 ns. The fluorescent detection of melamine in milk samples was realized by using the base pairing principle. Under the optimal conditions, the linear range of Bio-dots probe fluorescence sensor for melamine detection is 5-600 μM, and the detection limit is (3σ) 1.4 μM. Bio-dots can not only emit photoluminescence, but also detect target molecules as a functional recognition group. As the raw material ssDNA was basically non-toxic and there was no toxic substances participated in its synmanuscript process, this Bio-dots probe was a kind of green and environmentally-friendly photoluminescent functional material.

Efficient preparation of dual-emission ratiometric fluorescence sensor system based on aptamer-composite and detection of bis(2-ethylhexyl) phthalate in pork

A ratiometric fluorescence sensor system is proposed for detecting bis(2-ethylhexyl) phthalate (DEHP) in pork, which is based on aptamer recognition with molybdenum disulfide quantum dots and cadmium telluride quantum dots (MoS₂ QDs/CdTe-Apta). Two signals exist in the system, among which the response signal is transmitted by CdTe-Apta. The amide condensation between aptamers and CdTe QDs shortens the distance between CdTe QDs and DEHP, thus quenching the fluorescence of CdTe QDs, possibly through a photoinduced electron transfer mechanism. The MoS₂ QDs deliver the self-calibration signal, and the fluorescence of MoS₂ QDs remains almost constant when co-existing with DEHP. Linearity (R² = 0.9536) was established for the DEHP concentration range 0.005-3.0 mg·L^-1, with a limit of detection of 0.21 μg·L^-1. The system was successfully applied in the determination of DEHP in pork. The system has potential for the quantitative determination of DEHP in practical applications.

A Pyrene Fluorescent Probe for Rapid Detection of Ferric Ions

The 1,3,6,8-pyrenetetrasulfonic acid tetrasodium salt (PTSA) is a pyrene derivative with high fluorescence characteristics and is widely used in fluorescence tracer. This study aims at investigating a simple and fast fluorescence detection method for determining the concentration of ferric ion by using PTSA, which the principle is that the fluorescence quenching of PTSA by ferric ions. Theoretical and experimental methods were adopted to deeply analyze its detection performance and characteristics. The fluorescence quenching phenomena under different pH conditions and the effect of the different interfering metal ions on PTSA/Fe³⁺ system was studied. The results showed that the PTSA was quite promising for the fluorescence detection of trace ferric ions, and the limit of detection is 9 μg/L. This study is envisioned to provide inspirational insights on trace detection of iron ions, opening new routes for water monitoring use fluorescence properties.

A one-pot synthesis of fluorescent N,P-codoped carbon dots for vitamin B12 determination and bioimaging application

N,P-codoped carbon dots were synthesised using l-arginine and phosphoric acid and explored for the detection of vitamin B₁₂ (VB₁₂) and bioimaging.

A novel thioctic acid-carbon dots fluorescence sensor for the detection of Hg2+ and thiophanate methyl via S-Hg affinity

Mercury ions and thiophanate methyl (TM), are common contaminants present in the environment and food products. These contaminants cause neurovirulence and carcinogenicity effect on the human body. Herein, thioctic acid-carbon dots (SCDs) was synthesized and applied in a fluorescent "turn-off-on" probe to detect Hg²⁺ and TM. The presence of other common metal ions and pesticides did not affect the response of the developed sensor. Further investigation revealed that the fluorescent "turn-off-on" model were static, wherein the "turn-off" was induced by an electron transfer effect, while the "turn-on" was caused by the formation of TM-Hg complexes. Under optimal conditions, the fluorescence sensor method exhibited limits of detection as low as 33.3 nmol/L and 7.6 nmol/L for Hg²⁺ and TM, respectively. The developed sensor was designed to detect Hg²⁺ and TM in real tap water, grape juice and Citri Reticulatae Pericarpium (CRP) water samples.

Preparation of boron nitrogen co-doped carbon quantum dots for rapid detection of Cr(VI)

A novel fluorescent probe based on the static quenching and the inner filter effect between boron nitrogen co-doped carbon quantum dots (B, N-CDs) and Cr(VI) was developed for the quantitative determination of Cr(VI) in real water samples. B, N-CDs were prepared using the hydrothermal method with ammonium citrate and bis(pinacolato) diboron as raw materials. Compared with undoped CDs, the fluorescence properties of the B, N-CDs were improved. The fluorescence quantum yield of the B, N-CDs was as high as 59.01%. After optimization of the experimental parameters, the B, N-CDs could be used as a fluorescence probe to detect Cr(VI). Strong linear correlation (R² = 0.9986) was established in the Cr(VI) concentration range 0.3-500 μM, and a detection limit of 0.24 μM was achieved. Moreover, the B, N-CDs successfully detected Cr(VI) in real water samples, indicating that they have broad application prospects in the sensitive detection of Cr(VI).

Sensing of mercury ions in Porphyra by Copper @ Gold nanoclusters based ratiometric fluorescent aptasensor

A novel aptamer-modified Copper @ Gold nanoclusters (apt-Cu@Au NCs) based ratiometric fluorescent probe was developed for mercury ions (Hg²⁺) determination in Porphyra. The apt-Cu@Au NCs were well dispersed in solution without Hg²⁺ but combined together for the formation of thymidine-Hg-thymidine structure with the addition of Hg²⁺, which further caused the changes in their fluorescence intensities owing to fluorescence resonance energy transfer. Along with that, the changes in fluorescent colors are visible to the naked eye. Accordingly, Hg²⁺ were determined ranging from 0.1 to 9.0 μM by fluorescence analysis with the detection limit of 4.92 nM. Moreover, a homemade device utilizing smartphone and microfluidic chip was designed for colorimetric determination of Hg²⁺ ranging from 0.5 to 7.0 μM with good portability and usefulness. The proposed methods were used for Hg²⁺ detection in Porphyra with the recoveries of 101.83-114.00%, suggesting the considerable potential for evaluating Hg²⁺ levels in aquatic products.