Anionic dye uptake via composite using chitosan-polyacrylamide hydrogel as matrix containing TiO2 nanoparticles; comprehensive adsorption studies

Bio-based composite from chitosan waste and clay for effective removal of Congo red dye from contaminated water: Experimental studies and theoretical insights

Water pollution due to dyes in the textile industry is a serious environmental problem. During the finishing stage, Congo red (CR) dye, water-soluble, is released into wastewater, polluting the water body. This study explores the effectiveness of utilizing a composite composed of Safi raw clay and chitosan to remove an anionic dye from synthetic wastewater. The chitosan was extracted from crab shells. Its removal performance was compared to that of natural clay. Both the composite and raw clay were used to remove target pollutant. The effects of the chitosan load in the composite, size particles, initial dye concentration, contact time, pH, and temperature on the dye's elimination were tested in batch modes. The composite with 30% (w/w) of chitosan exhibited the highest dye removal. At pH 2, an adsorption capacity of 84.74 mg/g was achieved, indicating that the grafting of the polymer onto clay surface enhances its efficacity and stability in acidic environments. This finding was supported by characterization data obtained from X-ray diffraction (XRD), scanning electron microscopy (SEM), dispersive X-ray spectroscopy (EDX), and Fourier transform infrared (FT-IR) analyses. Under optimized conditions of 20 mg dose, pH 2, 30 min of reaction time, and 20 mg/L of dye concentration, about 92% of dye removal was achieved. The Langmuir isotherm model represents dye adsorption by the composite, while dye removal was controlled by pseudo-second-order model. Thermodynamic data of the adsorption (ΔH = +8.82 kJ/mol; ΔG <0) suggested that the dye adsorption was spontaneous and endothermic. The findings provide insights into the dye elimination by the adsorbent, indicating that the removal occurred via attractive colombic forces, as confirmed by density functional theory (DFT) analysis. Overall, the composite of natural clays and chitosan waste is a promising and innovative adsorbent for treating wastewater containing recalcitrant dyes.

Fabrication of carboxymethyl cellulose/graphene oxide/ZnO composite hydrogel for efficient removal of fuchsin dye from aqueous media

Hydrogels are hydrophilic, insoluble, and highly porous 3D networks capable of absorbing large amounts of water. This study aimed to develop a carboxymethyl cellulose/graphene oxide (CMC/GO) hydrogel, cross-linked with citric acid and modified with zinc oxide (ZnO) nanoparticles (CMC/GO/ZnO), synthesized via the sol-gel method. The formulated composite hydrogel samples were characterized by Fourier transmittance infrared spectroscopy (FTIR), scanning electron microscopy (SEM) analysis, X-ray diffraction (XRD), transmission electron microscopy (TEM), and thermo-gravimetric analysis (TGA). The hydrogels were tested for the adsorption of basic fuchsin (BF) dye from the aqueous medium under various conditions, such as adsorbent dosage, contact time, pH, and temperature, using batch adsorption. The adsorption data best fit the Langmuir and Temkin models, with maximum adsorption capacity (qmax) of 172.41 mg/g for CMC/GO and 303.03 mg/g for CMC/GO/ZnO. Optimal adsorption occurred at pH = 6 and within 30 min. The process followed a pseudo-second-order kinetic model, and thermodynamic results indicated that the adsorption process is physical, endothermic and spontaneous. The COOH groups in the hydrogels enhanced affinity for cationic dyes through hydrogen bonding and electrostatic interactions. Thus, CMC/GO and CMC/GO/ZnO hydrogels are efficient and promising adsorbents for environmental remediation.

Novel chitosan-based barrier materials for environmental containment: Synthesis, characterization, and contaminant removal capacities and mechanisms

This study critically appraises employing chitosan as a composite with bentonite, biochar, or both materials as an alternative to conventional barrier materials. A comprehensive literature review was conducted to identify the studies reporting chitosan-bentonite composite (CBC), chitosan amended biochar (CAB), and chitosan-bentonite-biochar composite (CBBC) for effective removal of various contaminants. The study aims to review the synthesis of these composites, identify fundamental properties affecting their adsorption capacities, and examine how these properties affect or enhance the removal abilities of other materials within the composite. Notably, CBC composites have the advantage of adsorbing both cationic and anionic species, such as heavy metals and dyes, due to the cationic nature of chitosan and the anionic nature of montmorillonite, along with the increased accessible surface area due to the clay. CAB composites have the unique advantage of being low-cost sorbents with high specific surface area, affinity for a wide range of contaminants owing to the high surface area and microporosity of biochar, and abundant available functional groups from the chitosan. Limited studies have reported the utilization of CBBC composites to remove various contaminants. These composites can be prepared by combining the steps employed in preparing CBC and CAB composites. They can benefit from the favorable adsorption properties of all three materials while also satisfying the mechanical requirements of a barrier material. This study serves as a knowledge base for future research to develop novel composite barrier materials by incorporating chitosan and biochar as amendments to bentonite.

Ammonia-responsive chitosan/polymethacrylamide double network hydrogels with high-stretchability, fatigue resistance and anti-freezing for real-time chicken breast spoilage monitoring

Hydrogels are a promising option for detecting food spoilage in humid conditions, but current indicators are prone to mechanical flaws, posing a concern for packaging systems that require strong mechanical properties. Herein, a double network hydrogel was prepared by polymerizing methacrylamide in a chitosan system with aluminum chloride and glycerol. The resulting hydrogel demonstrated high stretchability (strain >1500 %), notch insensitivity, excellent fatigue resistance, and exceptional anti-freezing capabilities even at -21 °C. When incorporating bromothymol blue (BB) or methyl red (MR), or mixtures of these dyes into the hydrogels as indicators, they exhibited sensitive colorimetric responses to pH and NH3 levels at different temperatures. Hydrogels immobilizing BB to MR ratios of 1:1 and 1:2 displayed clearer and more sensitive color responses when packed into chicken breast, with a sensitivity level of 1.5 ppm of total volatile basic nitrogen (TVB-N). This color response correlated positively with the accumulation of TVB-N on the packaging during storage at both 25 °C and 4 °C, providing sensitive indications of chicken breast deterioration. Overall, the developed hydrogels and indicators demonstrate enhanced performance characteristics, including excellent mechanical strength and highly NH3-sensitive color responses, making significant contributions to the food spoilage detection and intelligent packaging systems field.

Computational AI to predict and optimize the relationship between dye removal efficiency and Gibbs free energy in the adsorption process utilizing TiO2/chitosan-polyacrylamide composite

Building a model that can accurately anticipate and optimize the dynamics of dye removal and Gibbs free energy within the framework of an adsorption process is the main goal of this research. Furthermore, it has been determined that a correlation exists between the efficacy of dye removal and the behavior of Gibbs free energy throughout the process of adsorption. The study utilized a composite material consisting of chitosan-polyacrylamide/TiO2 as an adsorbent to remove anionic dye from a mainly aqueous solution. The parameters have been analyzed using response surface methodology (RSM), artificial neural networks (ANN), and machine learning (ML) techniques in this particular context. The obtained F-value of 814.62 for the RSM model, which assesses dye removal efficiency, suggests that the model under examination is statistically significant. Furthermore, based on the RSM data, the proposed model demonstrates a significant level of accuracy in predicting the performance of the TiO2/chitosan-polyacrylamide composite as an adsorbent during the dye removal adsorption process. The ANN model achieved a high level of accuracy, as evidenced by its R2 value of 0.999455. Through the utilization of neural networks and machine learning, the intended objective of forecasting dye removal efficiency and Gibbs free energy behavior in the adsorption process was effectively accomplished.

Tecoma stans floral extract-mediated synthesis of MgFe2O4/ZnO nanoparticles for adsorption and photocatalytic degradation of coomassie brilliant blue dye

Toxic organic dyes-containing wastewater treatment by adsorption and photocatalytic techniques is widely applied, but adsorbents and photocatalysts are often synthesized through chemical methods, leading to secondary pollution by released chemicals. Here, we report a benign method using Tecoma stans floral extract to produce MgFe2O4/ZnO (MGFOZ) nanoparticles for adsorption and photocatalytic degradation of coomassie brilliant blue (CBB) dye. Green MGFOZ owned a surface area of 9.65 m2/g and an average grain size of 54 nm. This bio-based nanomaterial showed higher removal percentage and better recyclability (up to five cycles) than green MgFe2O4 and ZnO nanoparticles. CBB adsorption by MGFOZ was examined by kinetic and isotherm models with better fittings of Bangham and Langmuir or Temkin. RSM-based optimization was conducted to reach an actual adsorption capacity of 147.68 mg/g. Moreover, MGFOZ/visible light system showed a degradation efficiency of 89% CBB dye after 120 min. CBB adsorption can be controlled by both physisorption and chemisorption while •O2- and •OH radicals are responsible for photo-degradation of CBB dye. This study suggested that MGFOZ can be a promising adsorbent and catalyst for removal of organic dyes in water.

Deciphering the photocatalytic degradation of polyaromatic hydrocarbons (PAHs) using hausmannite (Mn3O4) nanoparticles and their efficacy against bacterial biofilm

Polyaromatic hydrocarbons (PAHs) are life-threatening organic pollutants that severely threaten ecosystems worldwide due to their poisonous qualities, cancer-causing properties, and mutation-causing qualities. Water and soil together form a critical component of the ecosystem that supports all life. Due to the pollutants that are being disposed of in them, their characteristics have changed, and their toxicity has increased. The goal of this study was to investigate the ability of hausmannite nanoparticles to degrade fluorene from soil and water. Using the chemical method, hausmannite nanoparticles were synthesized and further characterization was performed using UV-Vis, FTIR, DLS, XRD, and SEM-EDAX. Hausmannite significantly degraded fluorene using the batch adsorption method. The degradation was also confirmed by performing reactive kinetics using Freundlich's isotherm model and Langmuir's pseudo-second-order model of soil and water. In addition to the degradation efficacy, hausmannite was also proved to inhibit biofilm formation by Pseudomonas aeruginosa. The findings of the experiments confirmed the presence of hausmannite nanoparticles, as well as their physical properties, chemical properties, degradation properties, and parameters of the kinetic study. As a result, synthesized nanoparticles have been extensively utilized as a low-cost option for removing pollutants and microbial biofilm.

Sustainable remediation of toxic congo red dye pollution using bio based carbon nanocomposite: Modelling and performance evaluation

Remediation of synthetic dyes found in aqueous environment poses a serious challenge for treatment due to their resistance to chemical and biological degradation. This research study investigated the application of Chitosan-ZnO-Seaweed bio nanocomposite in the remediation of congo red. The novel bionanocomposite was characterised by FTIR, SEM, TEM, EDS and XRD studies. The FTIR spectra and SEM images indicated the adsorption of congo red onto the synthesized bionanocomposite. The batch wise experimental studies were done to explore the influence of process variables on removal of congo red from synthetic wastewater and to determine optimized conditions. Under optimized conditions of pH 3, temperature 40 °C, initial congo red concentration 50 mg/L, bionanocomposite quantity 0.03 g/L and interaction period 30 min, the bionanocomposite removed 95.64% of congo red. Thermodynamic studies were carried out and the parameters, ΔH° and ΔS° were found to be 38.386 kJ/mol and 0.1451 kJ/mol. K, respectively. The isotherm and kinetic study showed that monolayer Langmuir model was obeyed (R2 = 0.968) and the experimental value of congo red adsorption correlated well with pseudo second order model (R2 = 0.9938) respectively. The maximum adsorption capacity was found to be 303.03 mg/g. Protonated amino group of chitosan, hydroxyl group of seaweed accounts for congo red adsorption along with zinc oxide.

Emerging micropollutants in aquatic ecosystems and nanotechnology-based removal alternatives: A review

There is a significant concern about the accessibility of uncontaminated and safe drinking water, a fundamental necessity for human beings. This concern is attributed to the toxic micropollutants from several emission sources, including industrial toxins, agricultural runoff, wastewater discharges, sewer overflows, landfills, algal blooms and microbiota. Emerging micropollutants (EMs) encompass a broad spectrum of compounds, including pharmaceutically active chemicals, personal care products, pesticides, industrial chemicals, steroid hormones, toxic nanomaterials, microplastics, heavy metals, and microorganisms. The pervasive and enduring nature of EMs has resulted in a detrimental impact on global urban water systems. Of late, these contaminants are receiving more attention due to their inherent potential to generate environmental toxicity and adverse health effects on humans and aquatic life. Although little progress has been made in discovering removal methodologies for EMs, a basic categorization procedure is required to identify and restrict the EMs to tackle the problem of these emerging contaminants. The present review paper provides a crude classification of EMs and their associated negative impact on aquatic life. Furthermore, it delves into various nanotechnology-based approaches as effective solutions to address the challenge of removing EMs from water, thereby ensuring potable drinking water. To conclude, this review paper addresses the challenges associated with the commercialization of nanomaterial, such as toxicity, high cost, inadequate government policies, and incompatibility with the present water purification system and recommends crucial directions for further research that should be pursued.

Emerging Mesoporous Polyacrylamide/Gelatin-Iron Lanthanum Oxide Nanohybrids towards the Antibiotic Drugs Removal from the Wastewater

The polyacrylamide/gelatin-iron lanthanum oxide (P-G-ILO nanohybrid) was fabricated by the free radical grafting co-polymerization technique in the presence of N,N-methylenebisacrylamide (MBA) as cross linker and ammonium persulfate (APS) as initiator. The P-G-ILO nanohybrid was characterized by the various spectroscopic and microscopic techniques that provided the information regarding the crystalline behavior, surface area, and pore size. The response surface methodology was utilized for the statistical observation of diclofenac (DF) adsorption from the wastewater. The adsorption capacity (qe, mg/g) of P-G-ILO nanohybrid was higher (254, 256, and 258 mg/g) than the ILO nanoparticle (239, 234, and 233 mg/g). The Freundlich isotherm model was the best fitted, as it gives the higher values of correlation coefficient (R2 = 0.982, 0.991 and 0.981) and lower value of standard error of estimate (SEE = 6.30, 4.42 and 6.52), which suggested the multilayered adsorption of DF over the designed P-G-ILO nanohybrid and followed the pseudo second order kinetic model (PSO kinetic model) adsorption. The thermodynamic study reveals that adsorption was spontaneous and endothermic in nature and randomness onto the P-G-ILO nanohybrids surface increases after the DF adsorption. The mechanism of adsorption of DF demonstrated that the adsorption was mainly due to the electrostatic interaction, hydrogen bonding, and dipole interaction. P-G-ILO nanohybrid was reusable for up to five adsorption/desorption cycles.

Using polyacrylamide hydrogel to adsorb chloride ions in cement-based materials

Concrete material is an important engineering material for modern marine engineering construction, but the presence of chloride ions in sea sand and seawater can cause corrosion of reinforcing steel, which greatly endangers the safety of reinforced concrete structures. Gel is an environmental friendly functional material which has the functions of exchange and adsorption of ions. Therefore, in this paper, polyacrylamide (PAM) gels were prepared for chloride ions adsorption in a reinforced concrete system. The chloride ions adsorption behavior of PAM gel in simulated seawater and cement were investigated and the maximum adsorption capacity of chloride ions in simulated seawater was 32.67 mg g-1. In addition, compared with the cement sample without gel, the chloride ion content in the cement sample containing 1.5 wt% gel was reduced 46.8% at a depth of 0-2.5 mm from the sample's surface. The results showed that PAM gel can effectively adsorb the chloride ion and improve the chloride ion penetration resistance in cement because the three-dimensional network structure of PAM gels allowed chloride ions to enter the inside of the gel. This gel has potential applications in the field of marine construction.

A comprehensive review on the metal-based green valorized nanocomposite for the remediation of emerging colored organic waste

In today's era, "green" synthesis is an emerging research trend. It has gained widespread attention owing to its dynamic behavior, reliability, simplicity, sustainability, and environment friendly approach for fabricating various nanomaterials. Green fabrication of metal/metal oxides nanomaterials, hybrid materials, and other metal-based nanocomposite can be utilized to remove toxic colored aqueous pollutants. Nanomaterials synthesized by using green approach is considered to be the significant tool to minimize unwanted or harmful by-products otherwise released from traditional synthesis methods. Various kinds of biosynthesized nanomaterials, such as animal waste and plant-based, have been successfully applied and well documented in the literature. However, their application part, especially for the cure of colored organic polluted water, has not been reported as a single review article. Therefore, the current work aims to assemble reports on using novel biosynthesized green metal-based nanomaterials to exclude harmful dyes from polluted water.

Statistical evaluation of liquid phase sequestration of acridine orange and Cr6+ by novel mesoporous glutamic acid-g-polyacrylamide/plaster of paris/riboflavin hydrogel nanocomposite

The adsorption of acridine orange and Cr⁶⁺ ion onto plaster of paris reinforced glutamic acid-grafted-polyacrylamide hydrogel nanocomposite modified with riboflavin, Glu-g-PAM/POP/Rb HNC was studied. The Glu-g-PAM/POP/Rb HNC was physico-chemically characterized by Fourier transform infrared spectroscopy, X-ray diffraction analysis, scanning electron microscopy coupled with energy dispersive X-ray spectroscopy, transmission electron microscopy and Brunauer-Emmett-Teller analysis. The specific surface area, pore volume and pore diameter were 15.48 m²/g, 0.015 cm³/g and 4.23 nm, respectively. Adsorption process was strategized by response surface methodology (RSM) based on a 3-level 5-factor (initial solution pH, contact time, adsorbent dose, initial adsorbate concentration and temperature) central composite design (CCD), and validity of the estimated parameters was statistically evaluated using analysis of variance (ANOVA). The optimized operating variables were: pH (AO = 10; Cr⁶⁺ = 4.15), contact time (AO = 60 min; Cr⁶⁺ = 59 min), adsorbent dose (0.8 g/L), initial adsorbate concentration (60 mg/L) and temperature (298 K). Isotherm results were coincident with Langmuir isotherm model. The experimental kinetic adsorption data was congruous with pseudo-second order model, with the uptake rate controlled by both intraparticle and liquid film diffusions. The relatively high Langmuir saturation capacity of 202.63 mg AO/g and 143.68 mg Cr⁶⁺/g, supported by the decent recyclability up to four times affirmed the promising performance of the adsorbent. The efficacy of the adsorbent for simultaneous removal of AO and Cr⁶⁺ from bi-component system was assessed. The possible adsorption mechanism mainly involved hydrogen bonding, van der Waals forces, electrostatic and π-π interactions. Adsorption of AO and Cr⁶⁺ onto Glu-g-PAM/POP/Rb HNC was feasible and exothermic as revealed by the thermodynamic parameters. The findings demonstrated superior adsorbent efficacy for the seizure of pollutants, particularly AO and Cr⁶⁺ from aqueous solution.

Adsorption of Magenta Dye on PbO Doped MgZnO: Interpretation of Statistical Physics Parameters Using Double-Layer Models

This article reports the synthesis of PbO doped MgZnO (PbO@MgZnO) by a co-precipitation method, followed by an ultrasonication process. PbO@MgZnO demonstrates a significant adsorption capability toward Magenta Dye (MD). The greatest adsorption capability was optimized by varying parameters such as pH, MD concentration, and adsorbent dose. The kinetics study illustrates that the adsorption of MD on PbO@MgZnO follows the pseudo-second-order. The isotherm study revealed that Langmuir is best fitted for the adsorption, but with little difference in the R² value of Langmuir and Freundlich, the adsorption process cloud be single or multi-layer. The maximum adsorption capacity was found to be 333.33 mg/g. The negative ΔG refers to the spontaneity of MD adsorption on PbO@MgZnO. The steric parameters from statistical physics models also favor the multi-layer adsorption mechanism. As a function of solution temperature, the parameter n pattern has values of n = 0.395, 0.290, and 0.280 for 298, 308, and 318 K, respectively (i.e., all values were below 1). Therefore, horizontal molecule positioning and multiple locking mechanisms were implicated during interactions between MD and PbO@MgZnO active sites.

Molecular Dynamics-Assisted Design of High Temperature-Resistant Polyacrylamide/Poloxamer Interpenetrating Network Hydrogels

Polyacrylamide has promising applications in a wide variety of fields. However, conventional polyacrylamide is prone to hydrolysis and thermal degradation under high temperature conditions, resulting in a decrease in solution viscosity with increasing temperature, which limits its practical effect. Herein, combining molecular dynamics and practical experiments, we explored a facile and fast mixing strategy to enhance the thermal stability of polyacrylamide by adding common poloxamers to form the interpenetrating network hydrogel. The blending model of three synthetic polyacrylamides (cationic, anionic, and nonionic) and poloxamers was first established, and then the interaction process between them was simulated by all-atom molecular dynamics. In the results, it was found that the hydrogen bonding between the amide groups on all polymers and the oxygen-containing groups (ether and hydroxyl groups) on poloxamers is very strong, which may be the key to improve the high temperature resistance of the hydrogel. Subsequent rheological tests also showed that poloxamers can indeed significantly improve the stability and viscosity of nonionic polyacrylamide containing only amide groups at high temperatures and can maintain a high viscosity of 3550 mPa·S at 80 °C. Transmission electron microscopy further showed that the nonionic polyacrylamide/poloxamer mixture further formed an interpenetrating network structure. In addition, the Fourier transform infrared test also proved the existence of strong hydrogen bonding between the two polymers. This work provides a useful idea for improving the properties of polyacrylamide, especially for the design of high temperature materials for physical blending.

Review on some metal oxide nanoparticles as effective adsorbent in wastewater treatment

Water contamination has turned into one of the most serious issues in the world. Nanomaterials are proficient to carry away heavy metals, organic and inorganic dyes, pesticides, and small molecules from polluted water. In this regard, nanoparticles have gained much attention due to their extraordinary properties compared to bulk materials. Metal oxide nanoparticles and nanocomposites have several advantages such as elevated surface area, low concentration, easily separable after treatment and so on. Among many feasible techniques, the adsorption process is one of the most useful techniques for removing heavy ions and dyes from wastewater and has gained much attention from researchers. Several studies on metal oxide nanoparticles and their use in wastewater treatment have been published in the literature. This chapter gives an outline about five metal oxide based nanomaterials and nanocomposites as well as their applications in water pollution removal where the efficiency, limits and favourable circumstances are compared and explored. This article surely helps to gather information about some metal oxide nanoparticles and nanocomposites in wastewater treatment by the adsorption technique. In this review article, we primarily focused on five metal oxide nanoparticles and some of their recent applications published in the last two years.

Study on a Hydrogel for Adsorption of Chloride Ions in Cementitious Materials

Chloride ions in the seaside environment can corrode the steel reinforcement in concrete, which greatly endangers the safety of seaside structures. As an excellent adsorption material, hydrogel is widely used in the field of water treatment but is rarely used in cementitious materials. In this study, a polyacrylamide–chitosan hydrogel (PAMC) was prepared with N,N-methylenebisacrylamide as the cross-linking agent and acrylamide as the monomer. The prepared PAMC gel could effectively adsorb chloride ions in simulated seawater and simulated sea sand environments, and the maximum adsorption capacity of chloride ions by PAMC-1 (prepared from 2.5 g acrylamide and 1% content of N,N-methylenebisacrylamide relative to acrylamide) gels in simulated seawater was 55.53 mg/g. The adsorption behavior of the PAMC gels in solution fit the Langmuir isotherm model. The composition and morphology of the PAMC gel were characterized, and the responsiveness of the PAMC gel to the environment was studied. The results showed that the PAMC gels adsorbed better in alkaline environments and thus could be used in alkaline cement-based environments. The mortar sample containing the PAMC-1 gel had higher resistance to chloride ion penetration, and the chloride ion content at 7.5–10mm from the surface of the sample cured for 28 days was reduced by 41.4% compared to the samples without the gel.

Impact of ZnO and Fe3O4 magnetic nanoscale on the methyl violet 2B removal efficiency of the activated carbon oak wood

In the current study, activated carbon oak wood (ACOW600) and modified activated carbon using ZnO (ACOW600/ZnO) and Fe₃O₄ (ACOW600/ZnO/Fe₃O₄) nanoparticles were used to remove methyl violet 2B dye (MV2B) from aqueous solutions. ACOW was synthesized at different temperatures (300-700 °C), and then the maximum MV2B removal efficiency (92.76 %) was achieved using ACOW synthesized at 600 °C. The morphology and characteristics of ACOW600, ACOW600/ZnO, and ACOW600/ZnO/Fe₃O₄ were studied using surface analyzes. According to the results, the adsorbents indicated a high ability to absorb MV2B from liquid solution, and their kinetic behavior follows a pseudo-second-order kinetic. In addition, the equilibrium study revealed that the MV2B uptake by the ACOW600/ZnO/Fe₃O₄ magnetic nanocomposite followed the Freundlich model. In contrast, the Langmuir model described the MV2B adsorption process using ACOW600 and ACOW600/ZnO. The maximum adsorption capacity (q_m) of MV2B using ACOW600, ACOW600/ZnO, and ACOW600/ZnO/Fe₃O₄ was determined 26.16 mg g^-1, 37.05 mg g^-1, and 48.59 mg g^-1, respectively, indicating that modification of ACOW600 led to improve its performance in removing MV2B. The enthalpy (ΔH), entropy (ΔG), and Gibbs free energy (ΔS) parameters revealed that the decontamination of MV2B using the studied adsorbents was exothermic and spontaneous. Also, random interactions of MV2B molecules and adsorbent surfaces were reduced during the adsorption process. Textile wastewater was significantly treated by ACOW600, ACOW600/ZnO, and ACOW600/ZnO/Fe₃O₄ adsorbents. The recycling of the adsorbents was demonstrated that the investigated adsorbents could be re-utilized many times in the MV2B removal process.

Remazol Brilliant Blue R (RBBR) dye and phosphate adsorption by calcium alginate beads modified with polyethyleneimine

This study concerns the preparation of novel adsorbent prepared from calcium alginate bead modified with polyethyleneimine (PEI-CaAlg). The adsorption capacity of the PEI-CaAlg was examined by Remazol Brilliant Blue R (RBBR) and phosphate adsorption. PEI-CaAlg showed high removal efficiencies for RBBR (90.48%) and phosphate (88.10%). The removal of both RBBR and phosphate onto the PEI-CaAlg followed the Freundlich isotherm and the second-order model. The adsorption was studied in terms of thermodynamic and found to be feasible and spontaneous in nature. The reusability of the modified alginate beads was also examined up to five cycles. The removal efficiency was 90.48% at the first cycle and decreased to 75.15% at the end of the fourth cycle. The adsorption of color and phosphate from real textile wastewater was also instigated. The removal efficiencies for color and phosphate ions reached 80.24% and 90.00%, respectively. Therefore, the prepared PEI-CaAlg can be considered as a novel, eco-friendly, and cost-effective adsorbent for simultaneous dye and phosphate adsorption. PRACTITIONER POINTS: This study aims to modify the surface of calcium alginate beads with polyethyleneimine (PEI). The adsorption of RBBR and phosphate by the modified alginate beads (PEI-CaAlg) was investigated. PEI is an organic polymer with a linear/branch shape, which can increase the active sites on the adsorbent surface. PEI has one nitrogen atom in every three atoms provides a positive charge that can complex with the negatively charged molecules. The adsorption of RBBR and phosphate were carried out onto PEI-CaAlg.

Development of a continuous fixed-bed column to eliminate cadmium(II) ions by starch-g-poly(acrylic acid)/cellulose nanofiber bio-nanocomposite hydrogel

This paper presents an experimental study on continuous adsorptive removal of Cd²⁺ from the water body using a bio-nanocomposite hydrogel within a fixed-bed column (FBC) system. The bio-nanocomposite hydrogel was synthesized based on starch grafted poly(acrylic acid) (St-g-PAA) reinforced by cellulose nanofibers (CNFs). The effects of processing conditions including pH, flow rate, and initial concentration of Cd²⁺ on adsorption efficiency were examined. Based on the results, the highest removal efficiency was achieved to be 82.5% at pH of 5, initial concentration of 10 mg L^-1, and flow rate of 5 mL min^-1. Furthermore, by applying isotherm models, it was uncovered that the Langmuir isotherm model was the most appropriate one, and the maximum adsorption capacity was 40.65 mg g^-1. Also, an adsorption process was carried out using the FBC system, and the outcome data were processed using Thomas and Yoon-Nelson models to find the characteristics of the column. In this study, the recovering capacity of the exhausted hydrogel was evaluated. Desorption process efficiencies of batch and continuous operations were obtained to be 91.9% and 90%, respectively.

Decoration of Citrus limon wood carbon with Fe3O4 to enhanced Cd2+ removal: A reclaimable and magnetic nanocomposite

In the present study, the activated carbon of lemon (ACL) was generated from Citrus limon wood waste and composited with Fe₃O₄ nanoparticles. The ACL/Fe₃O₄ magnetic composite was effectively used to eliminate Cd²⁺ from an aqueous solution. The active surface area values for ACL and ACL/Fe₃O₄ magnetic composite were 25.99 m²/g and 38.70 m²/g, respectively indicating the effectiveness of Fe₃O₄ nanoparticles in improving ACL active surface area. The response surface methodology with central composite design (RSM-CCD) was used to determine optimal values of pH, ACL/Fe₃O₄ dose, contact time, and Cd²⁺ concentration on the decontamination efficiency. The Langmuir and Freundlich isotherm models had more potential to describe the adsorption process using ACL and ACL/Fe₃O₄, respectively. The Langmuir-based adsorption capacity was obtained as 28.2 mg/g (ACL) and 39.6 mg/g (ACL/Fe₃O₄). A pseudo-second order (PSO) model was successfully applied to evaluate the adsorption process kinetic behavior. A higher value of α parameter for ACL/Fe₃O₄ (5.7 mg/g.min) than that of ACL (3.5 mg/g.min) indicated that the magnetic composite had a greater tendency to absorb Cd²⁺. In addition, the Weber-Morris model showed that various mechanisms such as intraparticle diffusion and boundary layer effects may have a role in the adsorption process. The study of ad(de)sorption behavior showed that the adsorbents have a good ability to adsorb Cd²⁺ and no significant change in their performance has been made up to 4 times of reuse. Our results showed that ACL modification using Fe₃O₄ nanoparticles improved the adsorption efficiency of ACL to remove Cd²⁺ from the aqueous solutions.

Preparation of clinoptilolite/starch/CoFe2O4 magnetic nanocomposite powder and its elimination properties for cationic dyes from water and wastewater

A new magnetic nanocomposite clinoptilolite (CLT)/Starch/CoFe₂O₄ was synthesized using co-precipitation method. The prepared magnetic composite powder was utilized for decontamination of methylene blue dye (MBD), methyl violet dye (MVD), and crystal violet dye (CVD) from water media. The BET analysis showed that CLT modification using starch and CoFe₂O₄ nanoparticles improved its specific surface and the amount of specific surface area for CLT, CoFe₂O_4, and CLT/Starch/CoFe₂O₄ powder was reported to be 18.82 m².g^-1, 151.4 m².g^-1, and 104.75 m².g^-1, respectively. Experimental results showed that pH 9 had a vital role in the adsorption process of all three types. Langmuir and Redlich-Petersen isotherm models were well fitted with experimental data. Also, the maximum adsorption capacity of CVD, MBD, and MVD to the desired composite was determined as 32.84 mg.g^-1, 31.81 mg.g^-1, and 31.15 mg.g^-1, respectively. In addition, the kinetic data of the removal process followed a pseudo-first order (PFO) kinetic model. Negative thermodynamic parameters were indicated that the process is spontaneous and exothermic. Finally, ad(de)sorption experiments' results showed that the synthesized nanocomposite adsorbent has an excellent ability to adsorb cationic dyes after several consecutive cycles.

Methylene blue removal with ZnO coated montmorillonite: thermodynamic, kinetic, isotherm and artificial intelligence studies

In this study, montmorillonite clay was coated with zinc oxide (ZnO) nanoparticles. The study's primary aim is to investigate the adsorption properties of zinc oxide coated montmorillonite adsorbent against methylene blue (MB), and determine ZnO's effectiveness in adsorption. First, the surface properties of the ZnO-coated montmorillonite (ZnO/MMT) adsorbent were determined by FTIR Spectroscopy, XRD, and SEM/EDS. In the adsorption studies, the effects of different parameters such as contact time (5-150 min), adsorbent dosage (0.05-0.5 g), initial concentration (50-200 mg/L), temperature (298-318 K), and initial pH (4-12) were investigated. In addition, a fuzzy model was developed by using adsorption parameters so that the removal rates could be calculated more quickly. Adsorption kinetics and equilibrium results were explained by the pseudo-second-order model and the Langmuir isotherm model, respectively. The highest adsorption capacity was calculated as 384.62 mg/g at 318 K. The enthalpy value was calculated as 2.16 kJ/mol. The entropy value was calculated as 0.04 kJ/mol K. The negative entropy value in the thermodynamic parameters calculated at all temperatures shows that the adsorption was spontaneous. According to the data we obtained, ZnO/MMT nanoparticles can be successfully applied for MB removal from aqueous solutions.

Adsorptive removal of eriochrome black T (EBT) dye by using surface active low cost zinc oxide nanoparticles: A comparative overview

The ecological toxicity imparted by non-biodegradable organic dyes has been considered as a major risk to handle in front of mankind. In this view, the low-cost zinc oxide nanoparticles (ZnO-NPs) were facially synthesized by coating the surface with surfactant (CTAB) and ionic liquid (BMTF) molecules for the effective removal of Eriochrome Black T (EBT) from aqueous media. Various advanced characterization techniques have given insight into the morphological features, crystalline structure and physio-chemical properties of as-synthesized ZnO-NPs. The systematic analysis of the adsorption isotherms and kinetics models specifies that the adsorption of EBT follow Freundlich model and pseudo-second-order kinetics. The intraparticle diffusion model displayed a linear relationship (R² = 0.98, 0.97 and 0.94 for BMTF@ZnO, CTAB@ZnO and bare ZnO-NPs), which shows that pore diffusion rate is affected by surface modification and effects the overall EBT adsorption process. Furthermore, after the removal of 87% and 84% of EBT dye by BMTF@ZnO-NPs and CTAB@ZnO-NPs, the fabricated nanoadsorbents of ZnO were successfully regenerated and reused after the treatments up to four times. The adsorption aptitude of ZnO-NPs towards EBT dye was systematically explored in real wastewater samples and interference study of inorganic metallic salts was also performed. The toxicity estimations of the treated dye solutions were made using floral and fungal activities, to ascertain their non-toxic nature before releasing into the environment. These outcomes have supported the immense potential of ZnO-NPs towards the removal of EBT in a cost effective manner.

Nanocomposite hydrogel based on sodium alginate, poly (acrylic acid), and tetraamminecopper (II) sulfate as an efficient dye adsorbent

In this study, a novel nanocomposite hydrogel (NCH) was prepared by in situ crosslinking and radical polymerization of acrylic acid (AA) in the presence of sodium alginate (Na-Alg), followed by loading of Cu²⁺ ions and reaction with ammonia. The main advantage of the synthesized NCH is the high adsorption of dye due to the large contact area. The structure of the NCH was studied by FT-IR spectroscopy, TEM, and SEM. TEM showed that the size of nanoparticles is about 5-30 nm. The adsorption of dye was studied by changing the different factors. The removal efficiency of Crystal Violet (CV) and Malachite Green (MG) was found to be more than 96% at concentration of 10 mg/L and pH = 6. The dye adsorption on the NCH is well described by Freundlich isotherm and pseudo-second-order kinetic models. The reusability experiments showed that about 95% of the initial adsorption was obtained after eight cycles.

Zn2+ removal from the aqueous environment using a polydopamine/hydroxyapatite/Fe3O4 magnetic composite under ultrasonic waves

In this study, an easily magnetically recoverable polydopamine (PDA)-modified hydroxyapatite (HAp)/Fe₃O₄ magnetic composite (HAp/Fe₃O₄/PDA) was suitably synthesized to exploit its adsorption capacity to remove Zn²⁺ from aqueous solution, and its structural properties were thoroughly examined using different analytical techniques. The effect of multiple parameters like pH, ultrasonic power, ultrasonic time, adsorbent dose, and initial Zn²⁺ concentration on the adsorption efficiency was assessed using RSM-CCD. According to the acquired results, by increasing the adsorbent quantity, ultrasonic power, ultrasonic time, and pH, the Zn²⁺ adsorption efficiency increased and the interaction between the variables of ultrasonic power/Zn²⁺ concentration, pH/Zn²⁺ concentration, pH/absorbent dose, and ultrasonic time/adsorbent dose has a vital role in the Zn²⁺ adsorption. The uptake process of Zn²⁺ onto PDA/HAp/Fe₃O₄ followed Freundlich and pseudo-second order kinetic models. The maximum capacity of Zn²⁺ adsorption (q _m) obtained by PDA/HAp/Fe₃O₄, HAp/Fe₃O₄, and HAp was determined as 46.37 mg g^-1, 40.07 mg g^-1, and 37.57 mg g^-1, respectively. Due to its good performance and recoverability (ten times), the HAp/Fe₃O₄/PDA magnetic composite can be proposed as a good candidate to eliminate Zn²⁺ ions from a water solution.

Chitosan-based hybrid materials for adsorptive removal of dyes and underlying interaction mechanisms

Environmental pollution by dyes molecules has become a subject of intensive research in recent years due to their hazardous effects on human health, organisms, and animals. Effective treatment and removal of dye molecules from the environmental matrices and water sources are of supreme concern. The deployment of cheap, safe, green, sustainable, and eco-friendly materials to remove these pollutants from water is the main challenge during the last decades. Chitosan and its derivatives/composites, as a cheap, easily available, and environmentally friendly sorbent, have attracted increasing attention for the removal of dye molecules. This review article focuses on the application of chitosan and chitosan-based smart adsorbents for the removal of dyes. Recent methods for the preparation of chitosan-based composites and their application in the removal of dyes are discussed. Moreover, the possible mechanisms for the interaction of chitosan and chitosan-based adsorbents with dyes molecules were evaluated. Finally, future prospects of using chitosan as an adsorbent for the removal of dye molecules are directed.

Chemical and physical Chitosan modification for designing enzymatic industrial biocatalysts: How to choose the best strategy?

Chitosan is one of the most abundant natural polymer worldwide, and due to its inherent characteristics, its use in industrial processes has been extensively explored. Because it is biodegradable, biocompatible, non-toxic, hydrophilic, cheap, and has good physical-chemical stability, it is seen as an excellent alternative for the replacement of synthetic materials in the search for more sustainable production methodologies. Thus being, a possible biotechnological application of Chitosan is as a direct support for enzyme immobilization. However, its applicability is quite specific, and to overcome this issue, alternative pretreatments are required, such as chemical and physical modifications to its structure, enabling its use in a wider array of applications. This review aims to present the topic in detail, by exploring and discussing methods of employment of Chitosan in enzymatic immobilization processes with various enzymes, presenting its advantages and disadvantages, as well as listing possible chemical modifications and combinations with other compounds for formulating an ideal support for this purpose. First, we will present Chitosan emphasizing its characteristics that allow its use as enzyme support. Furthermore, we will discuss possible physicochemical modifications that can be made to Chitosan, mentioning the improvements obtained in each process. These discussions will enable a comprehensive comparison between, and an informed choice of, the best technologies concerning enzyme immobilization and the application conditions of the biocatalyst.

Application of gradient acid fractionation protocol to improve decolorization technology by lignin-based adsorbent

Wastewater contaminated with dyes is discharged by huge amount daily, and involved many hazardous materials. Thus, this study focused on introducing low cost, ecofriendly and available removal agent (lignin-based adsorbent). Three adsorbents, APKL-4, APKL-5 and APKL-6 were obtained using gradient acid precipitation technology and used for methylene blue (MB) removal. The samples were characterized by SEM, FT-IR and zeta potential analyzer. The results indicated that the three adsorbents exhibit significantly different adsorption behavior due to the structural differences caused by fractionation. The APKL-5 and APKL-6 have fewer hydrophilic groups in their molecules and thus have more adsorption active sites to load MB molecules. A pore structure inside of APKL-5 molecules is form in acid fractionation, which allows it to carry more MB molecules. The adsorption capacity of APKL-5 increased 3.8 times (from 345 to 1310 mg g^-1) in the alkaline solution which showing excellent pH responsiveness. This paper presents a new promising approach for preparing high efficiency, low cost and eco-friendly adsorbents and builds a foundation for developing further applications of lignin-based adsorbents.