Cardiovascular stent design and vessel stresses: a finite element analysis

Structural optimization and in vitro corrosion analysis of biodegradable Mg-Nd-Zn-Zr alloy clip

Magnesium (Mg) alloy which benefits from biodegradability and mechanical characteristics offers great potential for the development of degradable hemostatic clips. However, the deformation process induces stress concentration, which in turn accelerates the corrosion rate of Mg hemostatic clips. In this study, two types of R-shape clips based on Mg-Nd-Zn-Zr alloy were designed with structural features of no teeth and staggered teeth and simulated using finite element analysis (FEA), and the corrosion behaviors of the Mg clips were investigated by immersion test and electrochemical measurement. Furthermore, the clamping properties of the Mg clips were evaluated by burst pressure test. The simulation results showed that the R-shape clip with staggered teeth caused the minimum stress (1.237 MPa) to blood vessels. After the clamping deformation process, the closed clips remained intact without any signs of cracking. In vitro degradation analysis indicated that the corrosion rate of the closed clip was slightly faster than that of the open clip, and the Mg clip maintained its efficacy in achieving vascular closure even after a 4-week period of immersion, indicating a commendable performance in secure ligation closure. In addition, the burst pressure test results showed that the staggered teeth clip exhibited a higher burst pressure (88.73 ± 2.58 kPa) with less mechanical damage occurring to the ligated vessels compared with the toothless clip, meeting the requirements for clinical application. Therefore, the newly developed R-shape Mg alloy clip, featuring staggered teeth, has demonstrated excellent mechanical stability and shows great promise in the application of biodegradable tissue clips.

Deforming Patient-Specific Models of Vascular Anatomies to Represent Stent Implantation via Extended Position Based Dynamics

PURPOSE

Angioplasty with stent placement is a widely used treatment strategy for patients with stenotic blood vessels. However, it is often challenging to predict the outcomes of this procedure for individual patients. Image-based computational fluid dynamics (CFD) is a powerful technique for making these predictions. To perform CFD analysis of a stented vessel, a virtual model of the vessel must first be created. This model is typically made by manipulating two-dimensional contours of the vessel in its pre-stent state to reflect its post-stent shape. However, improper contour-editing can cause invalid geometric artifacts in the resulting mesh that then distort the subsequent CFD predictions. To address this limitation, we have developed a novel shape-editing method that deforms surface meshes of stenosed vessels to create stented models.

METHODS

Our method uses physics-based simulations via Extended Position Based Dynamics to guide these deformations. We embed an inflating stent inside a vessel and apply collision-generated forces to deform the vessel and expand its cross-section.

RESULTS

We demonstrate that this technique is feasible and applicable for a wide range of vascular anatomies, while yielding clinically compatible results. We also illustrate the ability to parametrically vary the stented shape and create models allowing CFD analyses.

CONCLUSION

Our stenting method will help clinicians predict the hemodynamic results of stenting interventions and adapt treatments to achieve target outcomes for patients. It will also enable generation of synthetic data for data-intensive applications, such as machine learning, to support cardiovascular research endeavors.

Manufacturing, Processing, and Characterization of Self-Expanding Metallic Stents: A Comprehensive Review

This paper aims to review the State of the Art in metal self-expanding stents made from nitinol (NiTi), showing shape memory and superelastic behaviors, to identify the challenges and the opportunities for improving patient outcomes. A significant contribution of this paper is its extensive coverage of multidisciplinary aspects, including design, simulation, materials development, manufacturing, bio/hemocompatibility, biomechanics, biomimicry, patency, and testing methodologies. Additionally, the paper offers in-depth insights into the latest practices and emerging trends, with a special emphasis on the transformative potential of additive manufacturing techniques in the development of metal stents. By consolidating existing knowledge and highlighting areas for future innovation, this review provides a valuable roadmap for advancing nitinol stents.

A novel arterial coupler with non-return snap-fit connection approach optimized arterial end-to-end anastomotic technique: An experimental study

PURPOSE

Hand-sewn anastomosis as the gold standard of vascular anastomosis cannot fully meet the requirements of vascular anastomosis in speed and quality. Various vascular couplers have been developed to ameliorate this situation. Most of them are mainly used for venous anastomosis rather than arterial anastomosis, even though it is generally acknowledged that in almost all operations involving vascular reconstruction, it is the arteries that need to be anastomosed faster and more accurately and not the veins. A dedicated device is needed for creating arterial anastomosis in an easy, timesaving, less damaging but reliable procedure. Therefore, we plan to develop a novel arterial coupler device and test pre-clinical safety and effectiveness.

METHODS

In this cohort study, the rationality of this novel arterial coupler was preliminarily tested by finite element analysis before it was manufactured. Several factors restrict the use of vascular couplers in arterial anastomosis, such as arterial eversion, fixation, etc. The manufactured arterial couplers underwent in vitro and in vivo experiments. In vitro, isolated arteries of beagles were anastomosed with the assistance of an arterial coupler, and the anastomosed arteries were evaluated through anti-traction tests. In animal experiments, the bilateral femoral arteries of 5 beagles served as a control group. After dissection, the femoral artery on one side was randomly selected to be anastomosed with a quick arterial coupler (QAC) (QAC group), and the femoral artery on the other side was anastomosed by the same person using an end-to-end suture technique with a 6-0 Prolene suture (suture group). The bilateral femoral arteries of 5 beagles were used for coupler-assisted anastomosis and hand-sewn anastomosis in vivo, respectively. Success rate, blood loss, anastomotic time, clamp time, total operation time, and patency rate were recorded. The patency of anastomosed arteries was assessed using vascular Doppler ultrasound, electromagnetic flowmeter, and pathological examination (6 weeks after surgery).

RESULTS

As a novel arterial coupler, QAC was successfully designed and manufactured by using poly lactic-co-glycolic acid raw materials and 3-dimensions printing technology. Its rationality was preliminarily tested through finite element analysis and related mechanical analysis methods. The isolated arteries were successfully anastomosed with the assistance of QAC in vitro testing, which showed good anti-traction properties. In animal studies, QAC-assisted arterial anastomosis has superior profiles compared to hand-sewn anastomosis in anastomotic time (7.80 ± 1.41 vs. 16.38 ± 1.04 min), clamp time (8.80 ± 1.41 vs. 14.14 ± 1.57 min), and total operation time (46.64 ± 2.38 vs. 51.96 ± 3.65 min). The results of electromagnetic flowmeter, vascular Doppler ultrasound, and pathological examination showed that QAC-assisted anastomotic arteries were superior to hand-sewn arteries in terms of postoperative blood flow (16.86 ± 3.93 vs. 10.36 ± 0.92 mL/min) and vascular patency in 6 weeks after surgery.

CONCLUSION

QAC is a well-designed and easily maneuverable device specialized for end-to-end arterial anastomosis. Application of this device may decrease thermal ischemia time and improve the patency of anastomotic arteries, thus, improving outcomes.

Simplified Models to Assess the Mechanical Performance Parameters of Stents

Ischemic heart disease remains a leading cause of mortality worldwide, which has promoted extensive therapeutic efforts. Stenting has emerged as the primary intervention, particularly among individuals aged 70 years and older. The geometric specifications of stents must align with various mechanical performance criteria outlined by regulatory agencies such as the Food and Drug Administration (FDA). Finite element method (FEM) analysis and computational fluid dynamics (CFD) serve as essential tools to assess the mechanical performance parameters of stents. However, the growing complexity of the numerical models presents significant challenges. Herein, we propose a method to determine the mechanical performance parameters of stents using a simplified FEM model comprising solid and shell elements. In addition, a baseline model of a stent is developed and validated with experimental data, considering parameters such as foreshortening, radial recoil, radial recoil index, and radial stiffness of stents. The results of the simplified FEM model agree well with the baseline model, decreasing up to 80% in computational time. This method can be employed to design stents with specific mechanical performance parameters that satisfy the requirements of each patient.

A Novel Artificial Coronary Plaque to Model Coronary Heart Disease

BACKGROUND

Experimental coronary artery interventions are currently being performed on non-diseased blood vessels in healthy animals. To provide a more realistic pathoanatomical scenario for investigations on novel interventional and surgical therapies, we aimed to fabricate a stenotic lesion, mimicking the morphology and structure of a human atherosclerotic plaque.

METHODS

In an interdisciplinary setting, we engineered a casting mold to create an atherosclerotic plaque with the dimensions to fit in a porcine coronary artery. Oscillatory rheology experiments took place along with long-term stability tests assessed by microscopic examination and weight monitoring. For the implantability in future in vivo setups, we performed a cytotoxicity assessment, inserted the plaque in resected pig hearts, and performed diagnostic imaging to visualize the plaque in its final position.

RESULTS

The most promising composition consists of gelatin, cholesterol, phospholipids, hydroxyapatite, and fine-grained calcium carbonate. It can be inserted in the coronary artery of human-sized pig hearts, producing a local partial stenosis and interacting like the atherosclerotic plaque by stretching and shrinking with the vessel wall and surrounding tissue.

CONCLUSION

This artificial atherosclerotic plaque model works as a simulating tool for future medical testing and could be crucial for further specified research on coronary artery disease and is going to help to provide information about the optimal interventional and surgical care of the disease.

A comprehensive simulation framework for predicting the eCLIPs implant crimping into a catheter and its deployment mechanisms

Tubular flow diverters (FDs) represent an important subset of the endovascular treatment of cerebral aneurysms (CAs), acting to reduce aneurysm inflow, eventually resulting in aneurysm thrombosis and occlusion. eCLIPs (product of Evasc Neurovascular Enterprises, Vancouver, Canada), an innovative non-tubular implant causes flow diversion by bridging the neck of bifurcation CAs. However, in a small subset of challenging bifurcation aneurysms with fusiform pathology, the currently available eCLIPs models do not provide sufficient neck bridging resulting in a gap created between the device structure and the aneurysm/artery wall. To overcome this challenge, a new design of the eCLIPs (VR-eCLIPs) was developed by varying the rib length to cover such an inflow gap. To optimize the new product development process, and avoiding expensive and time-consuming iterative manufacture of prototype devices, we have developed a new finite element model to simulate the crimping and expansion processes of the VR-eCLIPs implant, and assess the possibility of plastic deformation. Results indicated that neither eCLIPs nor VR-eCLIPs experience plastic deformation during the crimping process. Upon full expansion, the ribs of VR-eCLIPs interact with the aneurysm and artery wall to cover the inflow gap that exists in certain challenging anatomies. This process serves as a basis to expedite design development prior to prototype manufacturing.

Near-wall hemodynamic parameters of finger arteries altered by hand-transmitted vibration

BACKGROUND

Sustained exposure to high-level hand-transmitted vibrations may result in angioneurotic disorders, which partly originate from vibration-altered hemodynamics in the finger arteries when repeating these disturbances throughout working life. Hence, the aim of this study is to assess the most relevant hemodynamic descriptors in the digital arteries, determine the relationship between the latter and vibration features, and gain better understanding of the physiological mechanisms involved.

METHODS

An experimental setup, mainly comprised of an ultra-high frequency ultrasound scanner and a vibration shaker, was used to image the digital proper volar arteries of the forefinger. Raw ultrasound data were post-processed by custom-made numerical routines to supply a pulsatile fluid mechanics model for computing the hemodynamic descriptors. Twenty-four healthy volunteers participated in the measurement campaign. Classical statistical methods were then applied to the dataset and also the wavelet transform for calculating the signal power in the frequency bands matching cardiac, respiratory, myogenic and neurogenic activities.

RESULTS

The artery diameter, the wall shear stress - WSS - and the WSS temporal gradient - WSSTG - were found to be the most relevant descriptors. Vibration-induced WSS was divided by three compared to its basal value whatever the vibration frequency and it was proportional to log2 of the acceleration level. Marked increases in WSSTG when stopping vibration might also lead to adverse health effects. Vibration caused a drop in WSS power for the frequency band associated with the neurogenic activity of the sympathetic nervous system.

CONCLUSION

This study may pave the way for a new framework to prevent vibration-induced vascular risk.

Load-sharing characteristics of stenting and post-dilation in heavily calcified coronary artery

In this work, stenting in non-calcified and heavily calcified coronary arteries was quantified in terms of diameter-pressure relationships and load transfer from the balloon to the artery. The efficacy of post-dilation in non-calcified and heavily calcified coronary arteries was also characterized in terms of load sharing and the changes in tissue mechanics. Our results have shown that stent expansion exhibits a cylindrical shape in non-calcified lesions, while it exhibits a dog bone shape in heavily calcified lesions. Load-sharing analysis has shown that only a small portion of the pressure load (1.4 N, 0.8% of total pressure load) was transferred to the non-calcified lesion, while a large amount of the pressure load (19 N, 12%) was transferred to the heavily calcified lesion. In addition, the increasing inflation pressure (from 10 to 20 atm) can effectively increase the minimal lumen diameter (from 1.48 to 2.82 mm) of the heavily calcified lesion, the stress (from 1.5 to 8.4 MPa) and the strain energy in the calcification (1.77 mJ to 26.5 mJ), which are associated with the potential of calcification fracture. Results indicated that increasing inflation pressure can be an effective way to improve the stent expansion if a dog bone shape of the stenting profile is observed. Considering the risk of a balloon burst, our results support the design and application of the high-pressure balloon for post-dilation. This work also sheds some light on the stent design and choice of stent materials for improving the stent expansion at the dog bone region and mitigating stresses on arterial tissues.

FEM Simulations of Fatigue Crack Initiation in the Oligocrystalline Microstructure of Stents

For over two decades, vascular stents have been widely used to treat clogged vessels, serving as a scaffold to enlarge the narrowed lumen and recover the arterial flow area. High-purity oligocrystalline austenitic steel is usually applied for the production of stents. Despite the popularity and benefit of stenting, it still may cause serious clinical adverse issues, such as in-stent restenosis and stent fracture. Therefore, the study of the mechanical properties of stents and in particular the prediction of their life cycles are in the focus of materials research. In our contribution, within the finite element method, a two-scale model of crack initiation in the microstructure of stents is elaborated. The approach is developed on the basis of the physically based Tanaka-Mura model (TMM), considering the evolution of shear bands during the crack initiation phase. The model allows for the analysis of the microstructure with respect to the life cycles of real materials. The effects of different loading conditions, grain orientation, and thickness of the specimen on Wöhler curves were analysed. It was found that the microstructural features of oligocrystals are very sensitive to different loading conditions with respect to their fatigue behaviour and play a major role in fatigue crack initiation. Different grain-orientation distributions result in qualitative and quantitative differences in stress distribution and in the number of cycles for crack initiation. It was found that presence of a neutral zone in the cut-out of the microstructure under three-point-bending loading conditions changes the qualitative and quantitative patterns of stress distribution and affects the number of cycles for crack initiation. It was found that under both tensile and bending loading conditions, thicker specimens require more cycles for crack initiation. The Wöhler curves for crack initiation in oligocrystalline microstructures of stents could be compared with the ones in the experiment, taking into account that for high cyclic fatigue (HCF), typically, more than 70% of the cycles refer to crack initiation. The developed numerical tools could be used for the material design of stents.

Load-sharing characteristics of stenting and post-dilation in heavily calcified coronary artery

In this work, stenting in non-calcified and heavily calcified coronary arteries was quantified in terms of diameter-pressure relationships and load transfer from the balloon to the artery. The efficacy of post-dilation in non-calcified and heavily calcified coronary arteries was also characterized in terms of load sharing and the changes in tissue mechanics. Our results have shown that stent expansion exhibits a cylindrical shape in non-calcified lesions, while it exhibits a dog bone shape in heavily calcified lesions. Load-sharing analysis has shown that only a small portion of the pressure load (1.4 N, 0.8% of total pressure load) was transferred to the non-calcified lesion, while a large amount of the pressure load (19 N, 12%) was transferred to the heavily calcified lesion. In addition, the increasing inflation pressure (from 10 to 20 atm) can effectively increase the minimal lumen diameter (from 1.48 mm to 2.82 mm) of the heavily calcified lesion, the stress (from 1.5 MPa to 8.4 MPa) the strain energy in the calcification (1.77 mJ to 26.5 mJ), which associated with the potential of calcification fracture. Results indicated that increasing inflation pressure can be an effective way to improve the stent expansion if a dog bone shape of the stenting profile is observed. Considering the risk of a balloon burst, our results support the design and application of the high-pressure balloon for post-dilation.

A Doppler-exclusive non-invasive computational diagnostic framework for personalized transcatheter aortic valve replacement

Given the associated risks with transcatheter aortic valve replacement (TAVR), it is crucial to determine how the implant will affect the valve dynamics and cardiac function, and if TAVR will improve or worsen the outcome of the patient. Effective treatment strategies, indeed, rely heavily on the complete understanding of the valve dynamics. We developed an innovative Doppler-exclusive non-invasive computational framework that can function as a diagnostic tool to assess valve dynamics in patients with aortic stenosis in both pre- and post-TAVR status. Clinical Doppler pressure was reduced by TAVR (52.2 ± 20.4 vs. 17.3 ± 13.8 [mmHg], p < 0.001), but it was not always accompanied by improvements in valve dynamics and left ventricle (LV) hemodynamics metrics. TAVR had no effect on LV workload in 4 patients, and LV workload post-TAVR significantly rose in 4 other patients. Despite the group level improvements in maximum LV pressure (166.4 ± 32.2 vs 131.4 ± 16.9 [mmHg], p < 0.05), only 5 of the 12 patients (41%) had a decrease in LV pressure. Moreover, TAVR did not always improve valve dynamics. TAVR did not necessarily result in a decrease (in 9 out of 12 patients investigated in this study) in major principal stress on the aortic valve leaflets which is one of the main contributors in valve degeneration and, consequently, failure of heart valves. Diastolic stresses increased significantly post-TAVR (34%, 109% and 81%, p < 0.001) for each left, right and non-coronary leaflets respectively. Moreover, we quantified the stiffness and material properties of aortic valve leaflets which correspond with the reduced calcified region average stiffness among leaflets (66%, 74% and 62%; p < 0.001; N = 12). Valve dynamics post-intervention should be quantified and monitored to ensure the improvement of patient conditions and prevent any further complications. Improper evaluation of biomechanical valve features pre-intervention as well as post-intervention may result in harmful effects post-TAVR in patients including paravalvular leaks, valve degeneration, failure of TAVR and heart failure.

Computational modeling of braided venous stents - Effect of design features and device-tissue interaction on stent performance

Designing venous stents with desired properties is challenging due to the partly conflicting performance criteria, e.g., enhancing flexibility may be at odds with increasing patency. To evaluate the effect of design parameters on the mechanical performance of braided stents, computational simulations are performed using finite element analysis. Model validation is performed through comparison with measurements. Considered design features are stent length, wire diameter, pick rate, number of wires, and stent end-type, being either open-ended or closed looped. Based on the requirements of venous stents, tests are defined to study the effect of design variations with respect to the following key performance criteria: chronic outward force, crush resistance, conformability, and foreshortening. Computational modeling is demonstrated to be a valuable tool in the design process through its ability of assessing sensitivities of various performance metrics to the design parameters. Additionally, it is shown, using computational modeling, that the interaction between a braided stent and its surrounding anatomy has a significant impact on its performance. Therefore, taking into account device-tissue interaction is crucial for the proper assessment of stent performance.

An ultrasound-exclusive non-invasive computational diagnostic framework for personalized cardiology of aortic valve stenosis

Aortic stenosis (AS) is an acute and chronic cardiovascular disease and If left untreated, 50% of these patients will die within two years of developing symptoms. AS is characterized as the stiffening of the aortic valve leaflets which restricts their motion and prevents the proper opening under transvalvular pressure. Assessments of the valve dynamics, if available, would provide valuable information about the patient's state of cardiac deterioration as well as heart recovery and can have incredible impacts on patient care, planning interventions and making critical clinical decisions with life-threatening risks. Despite remarkable advancements in medical imaging, there are no clinical tools available to quantify valve dynamics invasively or noninvasively. In this study, we developed a highly innovative ultrasound-based non-invasive computational framework that can function as a diagnostic tool to assess valve dynamics (e.g. transient 3-D distribution of stress and displacement, 3-D deformed shape of leaflets, geometric orifice area and angular positions of leaflets) for patients with AS at no risk to the patients. Such a diagnostic tool considers the local valve dynamics and the global circulatory system to provide a platform for testing the intervention scenarios and evaluating their effects. We used clinical data of 12 patients with AS not only to validate the proposed framework but also to demonstrate its diagnostic abilities by providing novel analyses and interpretations of clinical data in both pre and post intervention states. We used transthoracic echocardiogram (TTE) data for the developments and transesophageal echocardiography (TEE) data for validation.

Methodology for estimation of undeformed thickness of arterial tissues

Soft tissue sample thickness measurement is one of the major sources of differences between mechanical responses published by different groups. New method for the estimation of unloaded sample thickness of soft tissues is proposed in this study. Ten 30 × 30 mm and ten 20 × 20 mm samples of porcine anterior thoracic aortas were loaded by gradually increased radial force. Their deformed thickness was then recorded in order to generate a pressure-thickness response. Next, the limit pressure to which the response can be considered linear was estimated. Line was fitted to the linear part of the curve and extrapolated towards zero pressure to estimate unloaded thickness (7 kPa fit). For comparison, data near zero pressure were fitted separately and extrapolated towards zero (Near Zero fit). The limit pressure for the linearity of the response was around 7 kPa. The Unloaded thickness for 30 × 30 mm samples was 2.68 ± 0.31 mm and 2.68 ± 0.3 mm for Near Zero fit and 7 kPa fit, respectively. The Unloaded thickness for 20 × 20 mm samples was 2.60 ± 0.35 mm and 2.59 ± 0.35 mm for Near Zero fit and 7 kPa fit, respectively. The median of thickness difference between smaller and larger samples was not found statistically different. Proposed method can estimate unloaded undeformed sample thickness quickly and reliably.

Additive Manufacturing of Polyhydroxyalkanoate-Based Blends Using Fused Deposition Modelling for the Development of Biomedical Devices

In the last few decades Additive Manufacturing has advanced and is becoming important for biomedical applications. In this study we look at a variety of biomedical devices including, bone implants, tooth implants, osteochondral tissue repair patches, general tissue repair patches, nerve guidance conduits (NGCs) and coronary artery stents to which fused deposition modelling (FDM) can be applied. We have proposed CAD designs for these devices and employed a cost-effective 3D printer to fabricate proof-of-concept prototypes. We highlight issues with current CAD design and slicing and suggest optimisations of more complex designs targeted towards biomedical applications. We demonstrate the ability to print patient specific implants from real CT scans and reconstruct missing structures by means of mirroring and mesh mixing. A blend of Polyhydroxyalkanoates (PHAs), a family of biocompatible and bioresorbable natural polymers and Poly(L-lactic acid) (PLLA), a known bioresorbable medical polymer is used. Our characterisation of the PLA/PHA filament suggest that its tensile properties might be useful to applications such as stents, NGCs, and bone scaffolds. In addition to this, the proof-of-concept work for other applications shows that FDM is very useful for a large variety of other soft tissue applications, however other more elastomeric MCL-PHAs need to be used.

Patient-specific biomechanical analysis of atherosclerotic plaques enabled by histologically validated tissue characterization from computed tomography angiography: A case study

BACKGROUND

Rupture of unstable atherosclerotic plaques with a large lipid-rich necrotic core and a thin fibrous cap cause myocardial infarction and stroke. Yet it has not been possible to assess this for individual patients. Clinical guidelines still rely on use of luminal narrowing, a poor indicator but one that persists for lack of effective means to do better. We present a case study demonstrating the assessment of biomechanical indices pertaining to plaque rupture risk non-invasively for individual patients enabled by histologically validated tissue characterization.

METHODS

Routinely acquired clinical images of plaques were analyzed to characterize vascular wall tissues using software validated by histology (ElucidVivo, Elucid Bioimaging Inc.). Based on the tissue distribution, wall stress and strain were then calculated at spatial locations with varied fibrous cap thicknesses at diastolic, mean and systolic blood pressures.

RESULTS

The von Mises stress of 152 [131, 172] kPa and the equivalent strain of 0.10 [0.08, 0.12] were calculated where the fibrous cap thickness was smallest (560 μm) (95% CI in brackets). The stress at this location was at a level predictive of plaque failure. Stress and strain at locations with larger cap thicknesses were calculated to be lower, demonstrating a clinically relevant range of risk levels.

CONCLUSION

Patient specific tissue characterization can identify distributions of stress and strain in a clinically relevant range. This capability may be used to identify high-risk lesions and personalize treatment decisions for individual patients with cardiovascular disease and improve prevention of myocardial infarction and stroke.

Current status and outlook of biodegradable metals in neuroscience and their potential applications as cerebral vascular stent materials

Over the past two decades, biodegradable metals (BMs) have emerged as promising materials to fabricate temporary biomedical devices, with the purpose of avoiding potential side effects of permanent implants. In this review, we first surveyed the current status of BMs in neuroscience, and briefly summarized the representative stents for treating vascular stenosis. Then, inspired by the convincing clinical evidence on the in vivo safety of Mg alloys as cardiovascular stents, we analyzed the possibility of producing biodegradable cerebrovascular Mg alloy stents for treating ischemic stroke. For these novel applications, some key factors should also be considered in designing BM brain stents, including the anatomic features of the cerebral vasculature, hemodynamic influences, neuro-cytocompatibility and selection of alloying elements. This work may provide insights into the future design and fabrication of BM neurological devices, especially for brain stents.

•

The current status of the application of biodegradable metals (BM) in neuroscience was presented.

•

We analyzed the possibility of producing biodegradable cerebrovascular Mg alloy stents for ischemic stroke treatment.

•

Key factors in designing BM brain stents were discussed.

•

This work may provide insights into the future design and fabrication of BM neurological devices, especially for brain stents.

Assessing mechanical vibration-altered wall shear stress in digital arteries

The aim of this study is to implement and validate a method for assessing acute vibration-altered Wall Shear Stress (WSS) in the proper volar digital artery of the non-exposed left forefinger when subjecting the right hand to mechanical vibration. These changes of WSS may be involved in Vibration White Finger. Hence, an experimental device was set-up to link a vibration shaker and an ultra-high frequency ultrasound scanner. The Womersley-based WSS was computed by picking up the maximum velocity from pulse Wave Doppler measurements and extracting the artery diameter from B-mode images through an in-house image processing technique. The parameters of the former method were optimised on numerical ultrasound phantoms of cylindrical and lifelike arteries. These phantoms were computed with the FIELD II and FOCUS platforms which mimicked our true ultrasound device. The Womersley-based WSS were compared to full Fluid Structure Interaction (FSI) and rigid wall models built from resonance magnetic images of a volunteer-specific forefinger artery. Our FSI model took into account the artery's surrounding tissues. The diameter computing procedure led to a bias of 4%. The Womersley-based WSS resulted in misestimating the FSI model by roughly 10% to 20%. No difference was found between the rigid wall computational model and FSI simulations. Regarding the WSS measured on a group of 20 volunteers, the group-averaged basal value was 3 Pa, while the vibration-altered WSS was reduced to 1 Pa, possibly triggering intimal hyperplasia mechanisms and leading to the arterial stenoses encountered in patients suffering from vibration-induced Raynaud's syndrome.

Design optimization of a cardiovascular stent with application to a balloon expandable prosthetic heart valve

A cardiovascular stent design optimization method is proposed with application to a pediatric balloon-expandable prosthetic heart valve. The prosthetic valved conduit may be expanded to a larger permanent diameter in vivo via subsequent transcatheter balloon dilation procedures. While multiple expandable prosthetic heart valves are currently at different stages of development, this work is focused on one particular design in which a stent is situated inside of an expandable polymeric valved conduit. Since the valve and conduit must be joined with a robust manufacturing technique, a polymeric glue layer is inserted between the two, which results in radial retraction of the valved region after expansion. Design of an appropriate stent is proposed to counteract this phenomenon and maintain the desired permanent diameter throughout the device after a single non-compliant balloon dilation procedure. The finite element method is used to compute performance metrics related to the permanent expansion diameter and required radial force. Additionally, failure due not only to high cycle fatigue but also due to ductile fracture is incorporated into the design study through the use of an existing ductile fracture criterion for metals. Surrogate models are constructed with the results of the high fidelity simulations and are subsequently used to numerically obtain a set of Pareto-optimal stent designs. Finally, a single design is identified by optimizing a normalized aggregate objective function with equal weighting of all design objectives.

The Performance of a Spherical-tip Catheter for Stent Post-dilation: Finite Element Analysis and Experiments

At present, percutaneous coronary intervention (PCI) is the most effective treatment of coronary artery stenosis. However, in case post-dilation of the stent is needed, the tip of the commonly used post-dilation balloon catheter cannot always pass through the stent smoothly, especially when it is situated in the curved part of the vessel. To improve the performance of traditional post-dilation balloon catheter, a preliminary design of a novel catheter with a spherical-tip is proposed. Since the performance of this spherical-tip catheter is still unclear, in this study, finite element analysis (FEA) and experimental validation of blood vessel with different curvature radii were performed to test and evaluate the performance of the spherical-tip catheter design. The comparative results between the two types of catheters demonstrate that in the simulated post-dilation process, the spherical-tip catheter is easier to pass through the stent placed in the curved vessel without the deformation of the stent strut, and can theoretically reduce the operation time and improve the safety of the operation. Furthermore, the strong consistency between simulation and experiment indicates that the finite element (FE) model can be a helpful tool for future optimization and evaluation of novel catheters, so as to save time and budget in product development and reduce/replace animal studies.

Numerical Analysis for Non-Uniformity of Balloon-Expandable Stent Deployment Driven by Dogboning and Foreshortening

PURPOSE

Stenting is the most common intervention for arteriosclerosis treatment; however, the success of the treatment depends on the incidence of in-stent restenosis (ISR). Stent deployment characteristics are major influencers of ISR and can be measured in terms of dogboning, asymmetry, and foreshortening. This study aimed to analyse the implications of balloon and stent-catheter assembly parameters on the stent deployment characteristics.

METHODS

Experimental approach to analyse the impact of the balloon and stent-catheter assembly parameters on stent deployment characteristics is a time-consuming and complex task, whereas numerical methods prove to be quick, efficient, and reliable. In this study, eleven finite element models were employed to analyse non-uniform balloon stent expansion pattern, comprised of variation in, stent axial position on balloon, balloon length, balloon folding pattern, and balloon wall thickness.

RESULTS

Obtained results suggest that the axially noncentral position of the stent on balloon and variable balloon thickness lead to non-uniform stent deployment pattern. Also, it was proved that variation in balloon length and balloon folding pattern influence deployment process.

CONCLUSION

Improved positional accuracies, uniform balloon wall thickness, and selection of the appropriate length of a balloon for selected stent configuration will help to minimize dogboning, asymmetry, and foreshortening during non-uniform stent expansion, thereby reducing the risk of restenosis. The stated numerical approach will be helpful to optimize stent catheter assembly parameters thus minimizing in-vitro tests and product development time.

Validation of the computational model of a coronary stent: a fundamental step towards in silico trials

The proof of the reliability of a numerical model is becoming of paramount importance in the era of in silico clinical trials. When dealing with a coronary stenting procedure, the virtual scenario should be able to replicate the real device, passing through the different stages of the procedure, which has to maintain the atherosclerotic vessel opened. Nevertheless, most of the published studies adopted commercially resembling geometries and generic material parameters, without a specific validation of the employed numerical models. In this work, a workflow for the generation and validation of the computational model of a coronary stent was proposed. Possible sources of variability in the results, such as the inter-batches variability in the material properties and the choice of proper simulation strategies, were accounted for and discussed. Then, a group of in vitro tests, representative of the device intended use was used as a comparator to validate the model. The free expansion simulation, which is the most used simulation in the literature, was shown to be only partially useful for stent model validation purposes. On the other hand, the choice of proper additional experiments, as the suggested uniaxial tensile tests on the stent and deployment tests into a deformable tube, could provide further suitable information to prove the efficacy of the numerical approach.

Biodegradable performance of PLA stents affected by geometrical parameters: The risk of fracture and fragment separation

Biodegradable endovascular stents have been claimed to be reliable candidates for implantation devices used in treating cardiovascular diseases since they reduce the long-term side effects on the human biological system. It is aimed in this study to investigate the effect of geometrical parameters on the degradation behavior of poly (lactic acid) stents in term of strut fracture and fragment separation. In this regard, various structural geometry of the PLA stents was simulated in a stenosed artery using finite element method. For predicting the PLA degradation, a computational model was prepared by which the influence of stents design on their radial strength and fracture was investigated. Using a laboratory-scale designed bioreactor, the PLA fibers degradation was evaluated to calibrate the material parameters and verify the simulation method. Simulation results demonstrated that the geometrical parameters, i.e., number of struts, curves radius and stent cells shape, strongly affect the degradation behavior. The results indicated that the smooth design leads to uniform degradation in the whole stent and decreases the danger of stent fragments separation. It was shown that the maximum degradation rate of the stents with rounded curves was one-third of the models with sharp corners.

Computational and experimental mechanical performance of a new everolimus-eluting stent purpose-built for left main interventions

Left main (LM) coronary artery bifurcation stenting is a challenging topic due to the distinct anatomy and wall structure of LM. In this work, we investigated computationally and experimentally the mechanical performance of a novel everolimus-eluting stent (SYNERGY MEGATRON) purpose-built for interventions to large proximal coronary segments, including LM. MEGATRON stent has been purposefully designed to sustain its structural integrity at higher expansion diameters and to provide optimal lumen coverage. Four patient-specific LM geometries were 3D reconstructed and stented computationally with finite element analysis in a well-validated computational stent simulation platform under different homogeneous and heterogeneous plaque conditions. Four different everolimus-eluting stent designs (9-peak prototype MEGATRON, 10-peak prototype MEGATRON, 12-peak MEGATRON, and SYNERGY) were deployed computationally in all bifurcation geometries at three different diameters (i.e., 3.5, 4.5, and 5.0 mm). The stent designs were also expanded experimentally from 3.5 to 5.0 mm (blind analysis). Stent morphometric and biomechanical indices were calculated in the computational and experimental studies. In the computational studies the 12-peak MEGATRON exhibited significantly greater expansion, better scaffolding, smaller vessel prolapse, and greater radial strength (expressed as normalized hoop force) than the 9-peak MEGATRON, 10-peak MEGATRON, or SYNERGY (p < 0.05). Larger stent expansion diameters had significantly better radial strength and worse scaffolding than smaller stent diameters (p < 0.001). Computational stenting showed comparable scaffolding and radial strength with experimental stenting. 12-peak MEGATRON exhibited better mechanical performance than the 9-peak MEGATRON, 10-peak MEGATRON, or SYNERGY. Patient-specific computational LM stenting simulations can accurately reproduce experimental stent testing, providing an attractive framework for cost- and time-effective stent research and development.

Deformation mechanics of self-expanding venous stents: Modelling and experiments

Deformation properties of venous stents based on braided design, chevron design, Z design, and diamond design are compared using in vitro experiments coupled with analytical and finite element modelling. Their suitability for deployment in different clinical contexts is assessed based on their deformation characteristics. Self-expanding stainless steel stents possess superior collapse resistance compared to Nitinol stents. Consequently, they may be more reliable to treat diseases like May-Thurner syndrome in which resistance against a concentrated (pinching) force applied on the stent is needed to prevent collapse. Braided design applies a larger radial pressure particularly for vessels of diameter smaller than 75% of its nominal diameter, making it suitable for a long lesion with high recoil. Z design has the least foreshortening, which aids in accurate deployment. Nitinol stents are more compliant than their stainless steel counterparts, which indicates their suitability in veins. The semi-analytical method presented can aid in rapid assessment of topology governed deformation characteristics of stents and their design optimization.

A NEW RING STENT WITH GRADED GEOMETRY FOR TREATING COARCTATION OF CURVED AORTA ARTERIES

Ring stent implantation has been widely used to treat coarctation of the aorta (CoA) as an alternative to surgery. Currently adopted stents with uniform geometry may cause uneven stress distribution and high stress concentration in curved vessels, leading to in-stent restenosis (ISR). Inspired by functional graded material, here we propose a new ring-and-link stent, which has graded geometry in order to achieve a reduced peak stress when deployed in curved arteries. Numerical simulation of a single ring of the graded stent indicated that by varying the circumferential spacing of wave crest, the maximum stress exerted on the artery was reduced by as much as 27.86% in comparison with the uniform one. The effects of stent geometric parameters and artery curvature were also obtained through a parametric study. Finally, a whole stent was studied to verify the design, and a maximum stress reduction by 31.96% was achieved. In summary, the proposed graded ring stent shows great potential in clinical applications to reduce the risk of ISR.

The influence of angioplasty balloon sizing on acute post-procedural outcomes: a Finite Element Analysis

Atherosclerosis is one of the most common vascular pathologies in the world. Among the most commonly performed endovascular treatments, percutaneous transluminal angioplasty (PTA) has been showing significantly positive clinical outcomes. Due to the complex geometries, material properties and interactions that characterize PTA procedures, finite element analyses of acute angioplasty balloon deployment are limited. In this work, finite element method (FEM) was used to simulate the inflation and deflation of a semi-compliant balloon within the 3D model of a stenosed artery with two different plaque types (lipid and calcified). Self-defined constitutive models for the balloon and the plaque were developed based on experimental and literature data respectively. Balloon deployment was simulated at three different inflation pressures (10, 12 and 14 atm) within the two plaque types. Balloon sizing influence on the arterial elastic recoil obtained immediately after PTA was then investigated. The simulated results show that calcified plaques may lead to higher elastic recoil ratios compared to lipid stenosis, when the same balloon inflation pressures are applied. Also, elastic recoil increases for higher balloon inflation pressure independent of the plaque type. These findings open the way for a data-driven assessment of angioplasty balloon sizing selection and clinical procedures optimization.Clinical Relevance- The FE model developed in this work aims at providing quantitative evaluation of recoil after balloon angioplasty. It may be useful for both manufacturers and clinicians to improve efficiency of angioplasty balloon device design and sizing selection with respect to plaque geometry and constitution, consequently enhancing clinical outcomes.

A nonlinear rotation-free shell formulation with prestressing for vascular biomechanics

We implement a nonlinear rotation-free shell formulation capable of handling large deformations for applications in vascular biomechanics. The formulation employs a previously reported shell element that calculates both the membrane and bending behavior via displacement degrees of freedom for a triangular element. The thickness stretch is statically condensed to enforce vessel wall incompressibility via a plane stress condition. Consequently, the formulation allows incorporation of appropriate 3D constitutive material models. We also incorporate external tissue support conditions to model the effect of surrounding tissue. We present theoretical and variational details of the formulation and verify our implementation against axisymmetric results and literature data. We also adapt a previously reported prestress methodology to identify the unloaded configuration corresponding to the medically imaged in vivo vessel geometry. We verify the prestress methodology in an idealized bifurcation model and demonstrate the significance of including prestress. Lastly, we demonstrate the robustness of our formulation via its application to mouse-specific models of arterial mechanics using an experimentally informed four-fiber constitutive model.

A NOVEL STRUCTURE DESIGN OF BIODEGRADABLE ZINC ALLOY STENT AND ITS EFFECTS ON RESHAPING STENOTIC VESSEL

Biodegradable zinc alloy stents offer a prospective solution to mitigate incompatibility between artery and permanent stents. However, biodegradable stents are restricted in clinical therapy mainly because of their insufficient support for opening of stenotic vessel. As an effort to resolve this challenging problem, a novel structure of zinc alloy stent which significantly enhanced scaffold performance is proposed in this paper. Subsequently, the functionality of the new stent on reshaping vessels with 40% of stenosis was investigated in contrast with a common stent via finite element analysis. The simulation results show that radial recoiling ratio and dog-boning ratio of the new stent are decreased by 43.2% and 16.3%, respectively, compared with those of the common stent. A larger and flatter lumen is found in the plaque-vessel system deployed with the new stent. It suggests that the geometry of stent has strong influence on its mechanical performance. With strong scaffold capability and brilliant effect on reshaping stenotic vessel, the biodegradable zinc alloy stent-based novel structure is highly promised to be an alternative choice in interventional surgeries.

Numerical analysis of paclitaxel-eluting coronary stents: Mechanics and drug release properties

Since theoretical models provide data that cannot be otherwise gathered, numerical methods applied to medical devices analysis have emerged as fundamental tool in preclinical development. Large efforts were done to study mechanical and drug-eluting properties in stents but often the coating modelling is neglected. This work presents a finite element framework to calculate mechanical loads and drug distribution in three commercial drug-eluting stents (Palmaz-Schatz, Palmaz Genesis and Multi Link Vision), to check coatings strength and drug distribution maps in biological tissues. The promising copolymer poly(methylmethacrylate-co-n-butylmethacrylate), loaded with paclitaxel, is analyzed. Results demonstrated that the coating undergoes localized plastic phenomena, and calculated stresses are lower than the ultimate stress, ensuring coating integrity. Computed drug concentration depends on stent geometry and its values are in all cases lower than the toxicity level for this drug.

Numerical study to identify the effect of fluid presence on the mechanical behavior of the stents during coronary stent expansion

In this study, structural analysis and one-way fluid-structure interaction (FSI) analysis were performed to identify the effect of fluid presence on the mechanical behavior of the stents during stent expansion. An idealized vessel model with stenosis was used for simulation, and stents made of metal and polymer were assumed, respectively. The bilinear model was applied to the stents, and the Mooney-Rivlin model was applied to the arterial wall and plaque. The blood used in the FSI analysis was assumed to be a non-Newtonian fluid. As a result of all numerical simulations, the von Mises stress, the first principal stress and the displacement were calculated as the mechanical behaviors. Through the comparison of the results of the structural analysis with those of the one-way FSI analysis, our results indicated the fluid had no significant influence on the expansion of the metal stent. However, it was found that the expansion of the polymer stent affected by the presence of fluid. These findings meant the one-way FSI technique was suggested to achieve an accurate analysis when targeting a polymer stent for numerical simulation.

Characterization of hyperelastic and damage behavior of tendons

In this paper, we characterized the hyperelastic and damage behavior of the Extensor Digitorum Longus (EDL) human tendon under loading conditions. The study was conducted in both categories of models, phenomenological and physically motivated, to allow the prediction and the macroscopic response of the tendon under specific loading conditions, assuming that its response follows a hyperelastic anisotropic model in conjunction with damage law. We benchmarked multiple hyperelastic and damage models to fit the response of the tendons in uniaxial tensile loading conditions, and by employing a genetic algorithm, we obtained the material parameters for both elastic and damage models. The objective of this study was to explore different mathematical models to determine which would be the best option to predict the behavior of tendons and ligaments in complex biological systems using Finite Elements (FE) models. Therefore, we took into account accuracy as well as computational features. We considered the model proposed by Shearer and coupled it with a sigmoid function, which governs the evolution of damage in tendons, as the most appropriate for the fitting of the experimental data. The achieved solution shows to be of high interest attributable to the simplicity of the damage law function and its low computational cost.

NUMERICAL INVESTIGATION ON INFLUENCE OF VASCULAR STENOSIS RATE AND CURVATURE RADIUS ON PLAQUE VULNERABILITY IN STENTED VESSELS

The high stresses on plaque wall experienced by stent implantation into a stenotic artery can go beyond the material strength of plaque tissue, potentially leading to plaque rupture. Two non-commercial stents with different link structures called S-type and N-type were taken into account, respectively. A non-linear finite element model was developed to investigate the influence of the stenosis level (i.e., 24%, 40%, and 50%) and arterial curvature radius (i.e., 6, 10, and 20[Formula: see text]mm) on the stress induced within the plaque tissue during stent expansion. The numerical results indicated that the severer stenosis level and more tortuous artery caused the higher stress on plaque wall. The maximal stresses on the plaque wall were in the fracture level of 1.79[Formula: see text]MPa for N-type stent, and 1.82[Formula: see text]MPa for S-type stent under the 50% stenosis rate and 6[Formula: see text]mm curvature radius. Due to smaller compliance mismatch to the curved vessel, the N-type stent was founded to induce less stress gradient on the plaque wall than that by the S-type stent. This suggests a lower risk of the plaque rupture for the N-type stent. This study showed how the arterial curvature radius and stenosis level were correlated with the plaque vulnerability. Therefore, it is possible to choose a suitable stent in terms of arterial stenosis geometry and thereby optimize the outcome of stenting procedure.

Analysing The Cross-Section of The Abdominal Aortic Aneurysm Neck and Its Effects on Stent Deployment

Stent graft devices for the treatment of abdominal aortic aneurysms (AAAs) are being increasingly used worldwide. Yet, during modelling and optimization of these devices, as well as in clinical practice, vascular sections are idealized, possibly compromising the effectiveness of the intervention. In this study, we challenge the commonly used approximation of the circular cross-section of the aorta and identify the implications of this approximation to the mechanical assessment of stent grafts. Using computed tomography angiography (CTA) data from 258 AAA patients, the lumen of the aneurysmal neck was analysed. The cross-section of the aortic neck was found to be an independent variable, uncorrelated to other geometrical aspects of the region, and its shape was non-circular reaching elliptical ratios as low as 0.77. These results were used to design a finite element analysis (FEA) study for the assessment of a ring stent bundle deployed under a variety of aortic cross-sections. Results showed that the most common clinical approximations of the vascular cross-section can be a source of significant error when calculating the maximum stent strains (underestimated by up to 69%) and radial forces (overestimated by up to 13%). Nevertheless, a less frequently used average approximation was shown to yield satisfactory results (5% and 2% of divergence respectively).

Three-dimensional numerical simulation of soft-tissue wound healing using constrained-mixture anisotropic hyperelasticity and gradient-enhanced damage mechanics

Healing of soft biological tissues is the process of self-recovery or self-repair after injury or damage to the extracellular matrix (ECM). In this work, we assume that healing is a stress-driven process, which works at recovering a homeostatic stress metric in the tissue by replacing the damaged ECM with a new undamaged one. For that, a gradient-enhanced continuum healing model is developed for three-dimensional anisotropic tissues using the modified anisotropic Holzapfel-Gasser-Ogden constitutive model. An adaptive stress-driven approach is proposed for the deposition of new collagen fibres during healing with orientations assigned depending on the principal stress direction. The intrinsic length scales of soft tissues are considered through the gradient-enhanced term, and growth and remodelling are simulated by a constrained-mixture model with temporal homogenization. The proposed model is implemented in the finite-element package Abaqus by means of a user subroutine UEL. Three numerical examples have been achieved to illustrate the performance of the proposed model in simulating the healing process with various damage situations, converging towards stress homeostasis. The orientations of newly deposited collagen fibres and the sensitivity to intrinsic length scales are studied through these examples, showing that both have a significant impact on temporal evolutions of the stress distribution and on the size of the damage region. Applications of the approach to carry out in silico experiments of wound healing are promising and show good agreement with existing experiment results.

Future Balloon-Expandable Stents: High or Low-Strength Materials?

PURPOSE

Recent progress in material science allows researchers to use novel materials with enhanced capabilities like optimum biodegradability, higher strength, and flexibility in the design of coronary stents. Considering the wide range of mechanical properties of existing and newfangled materials, finding the influence of variations in mechanical properties of stent materials is critical for developing a practical design.

METHODS

The sensitivity of stent functional characteristics to variations in its material plastic properties is obtained through FEM modeling. Balloon-expandable coronary stent designs: Absorb BVS, and Xience are examined for artificial and commercial polymeric, and metallic materials, respectively. Standard tests including (1) the crimping process followed by stent implantation in an atherosclerotic artery and (2) the three-point bending test, have been simulated according to ASTM standards.

RESULTS

In Absorb BVS, materials with higher yield stress than PLLA have similar residual deflection and maximum bending force to PLLA, which is not the case for Xience stent and Co-Cr. Moreover, elevated yield stress significantly reduces stent flexibility only in Xience stent. For both stents, with different degree of influence, an increase in yield or ultimate stress improves stent radial strength and stiffness and reduces arterial stress and plastic strain of stent, which consequently enhances the stent mechanical performance. Contrarily, yield or ultimate stress elevation increases stent recoil which adversely affects stent performance.

CONCLUSION

Using high-strength materials has a double-edged sword effect on the stent performance and existing uncertainty in the precise estimate of stent mechanical properties adversely affects the reliability of numerical models' predictions.

Structural and Hemodynamic Analyses of Different Stent Structures in Curved and Stenotic Coronary Artery

Coronary artery stenting is commonly used for the treatment of coronary stenosis, and different stent structures indeed have various impacts on the stress distribution within the plaque and artery as well as the local hemodynamic environment. This study aims to evaluate the performance of different stent structures by characterizing the mechanical parameters after coronary stenting. Six stent structures including three commercially-shaped stents (Palmaz-Schatz-shaped, Xience Prime-shaped, and Cypher-shaped) and three author-developed stents (C-Rlink, C-Rcrown, and C-Astrut) implanted into a curved stenotic coronary artery were investigated. Structural analyses of the balloon-stent-plaque-artery system were first performed, and then followed by hemodynamic analyses. The results showed that among the three commercially-shaped stents, the Palmaz-Schatz-shaped had the least stent dogboning and recoiling, corresponding to the greatest maximum plastic strain and the largest diameter change, nevertheless, it induced the highest maximum von Mises stress on plaque, arterial intima and media. From the viewpoint of hemodynamics, the Palmaz-Schatz-shaped displayed smaller areas of adverse low wall shear stress (<0.5 Pa), low time-averaged wall shear stress (<0.5 Pa), and high oscillating shear index (>0.1). Compared to the Cypher-shaped, the C-Rcrown and C-Astrut had smaller recoiling, greater maximum plastic stain and larger diameter change, which indicated the improved mechanical performance of the Cypher-shaped stent. Moreover, both C-Rcrown and C-Astrut exhibited smaller areas of adverse low wall shear stress, and low time-averaged wall shear stress, but only the C-Rcrown displayed a smaller area of adverse high oscillating shear index. The present study evaluated and compared the performance of six different stents deployed inside a curved artery, and could be potentially utilized as a guide for the selection of suitable commercially-shaped stent for clinical application, and to provide an approach to improve the performance of the commercial stents.

Fluid-Structure Interaction Simulation of Blood Flow and Cerebral Aneurysm: Effect of Partly Blocked Vessel

In this study, using fluid-structure interaction (FSI), 3-dimensional blood flow in an aneurysm in the circle of Willis - which is located in the middle cerebral artery (MCA) - has been simulated. The purpose of this study is to evaluate the effect of a partly blocked vessel on an aneurysm. To achieve this purpose, two cases have been investigated using the FSI method: in the first case, an ideal geometry of aneurysm in the MCA has been simulated; in the second case, modeling is performed for an ideal geometry of the aneurysm in the MCA with a partly blocked vessel. All boundary conditions, properties and modeling methods were considered the same for both cases. The only difference between the two cases was that part of the MCA parent artery was blocked in the second case. In order to consider the hyperelastic property of the wall and the non-Newtonian properties of the blood, the Mooney-Rivlin model and the Carreau model have been used, respectively. In the second case, the Von Mises stress in the peak systole is 26% higher than in the first case. With regard to the high amount of Von Mises stress, the risk of rupture of the aneurysm is higher in this case. In the second case, the maximum wall shear stress (WSS) is 12% higher than in the first case. And maximum displacement in the second case is also higher than in the first. So, the risk of growth of the aneurysm is higher in cases with a partly blocked vessel.

Experimentally validated simulation of coronary stents considering different dogboning ratios and asymmetric stent positioning

In-stent restenosis remains a major problem of arteriosclerosis treatment by stenting. Expansion-optimized stents could reduce this problem. With numerical simulations, stent designs/ expansion behaviours can be effectively analyzed. For reasons of efficiency, simplified models of balloon-expandable stents are often used, but their accuracy must be challenged due to insufficient experimental validation. In this work, a realistic stent life-cycle simulation has been performed including balloon folding, stent crimping and free expansion of the balloon-stent-system. The successful simulation and validation of two stent designs with homogenous and heterogeneous stent stiffness and an asymmetrically positioned stent on the balloon catheter confirm the universal applicability of the simulation approach. Dogboning ratio, as well as the final dimensions of the folded balloon, the crimped and expanded stent, correspond well to the experimental dimensions with only slight deviations. In contrast to the detailed stent life-cycle simulation, a displacement-controlled simulation can not predict the transient stent expansion, but is suitable to reproduce the final expanded stent shape and the associated stress states. The detailed stent life-cycle simulation is thus essential for stent expansion analysis/optimization, whereas for reasons of computational efficiency, the displacement-controlled approach can be considered in the context of pure stress analysis.

Computational modelling of magnesium stent mechanical performance in a remodelling artery: Effects of multiple remodelling stimuli

Significant research has been conducted in the area of coronary stents/scaffolds made from resorbable metallic and polymeric biomaterials. These next-generation bioabsorbable stents have the potential to completely revolutionise the treatment of coronary artery disease. The primary advantage of resorbable devices over permanent stents is their temporary presence which, from a theoretical point of view, means only a healed coronary artery will be left behind following degradation of the stent potentially eliminating long-term clinical problems associated with permanent stents. The healing of the artery following coronary stent/scaffold implantation is crucial for the long-term safety of these devices. Computational modelling can be used to evaluate the performance of complex stent devices in silico and assist in the design and development and understanding of the next-generation resorbable stents. What is lacking in computational modelling literature is the representation of the active response of the arterial tissue in the weeks and months following stent implantation, ie, neointimal remodelling, in particular for the case of biodegradable stents. In this paper, a computational modelling framework is developed, which accounts for two major physiological stimuli responsible for neointimal remodelling and combined with a magnesium corrosion model that is capable of simulating localised pitting (realistic) stent corrosion. The framework is used to simulate different neointimal growth patterns and to explore the effects the neointimal remodelling has on the mechanical performance (scaffolding support) of the bioabsorbable magnesium stent.

Patient specific characterization of artery and plaque material properties in peripheral artery disease

Patient-specific finite element (FE) modeling of atherosclerotic plaque is challenging, as there is limited information available clinically to characterize plaque components. This study proposes that for the limited data available in vivo, material properties of plaque and artery can be identified using inverse FE analysis and either a simple neo-Hookean constitutive model or assuming linear elasticity provides sufficient accuracy to capture the changes in vessel deformation, which is the available clinical metric. To test this, 10 human cadaveric femoral arteries were each pressurized ex vivo at 6 pressure levels, while intravascular ultrasound (IVUS) and virtual histology (VH) imaging were performed during controlled pull-back to determine vessel geometry and plaque structure. The VH images were then utilized to construct FE models with heterogeneous material properties corresponding to the vessel plaque components. The constitutive models were then fit to each plaque component by minimizing the difference between the experimental and the simulated geometry using the inverse FE method. Additionally, we further simplified the analysis by assuming the vessel wall had a homogeneous structure, i.e. lumping artery and plaque as one tissue. We found that for the heterogeneous wall structure, the simulated and experimental vessel geometries compared well when the fitted neo-Hookean parameters or elastic modulus, in the case of linear elasticity, were utilized. Furthermore, taking the median of these fitted parameters then inputting these as plaque component mechanical properties in the finite element simulation yielded differences between simulated and experimental geometries that were on average around 2% greater (1.30-5.55% error range to 2.33-11.71% error range). For the homogeneous wall structure the simulated and experimental wall geometries had an average difference of around 4% although when the difference was calculated using the median fitted value this difference was larger than for the heterogeneous fits. Finally, comparison to uniaxial tension data and to literature constitutive models also gave confidence to the suitability of this simplified approach for patient-specific arterial simulation based on data that may be acquired in the clinic.

Sensitivity of Arterial Hyperelastic Models to Uncertainties in Stress-Free Measurements

Despite major advances made in modeling vascular tissue biomechanics, the predictive power of constitutive models is still limited by uncertainty of the input data. Specifically, key measurements, like the geometry of the stress-free (SF) state, involve a definite, sometimes non-negligible, degree of uncertainty. Here, we introduce a new approach for sensitivity analysis of vascular hyperelastic constitutive models to uncertainty in SF measurements. We have considered two vascular hyperelastic models: the phenomenological Fung model and the structure-motivated Holzapfel-Gasser-Ogden (HGO) model. Our results indicate up to 160% errors in the identified constitutive parameters for a 5% measurement uncertainty in the SF data. Relative margins of errors of up to 30% in the luminal pressure, 36% in the axial force, and over 200% in the stress predictions were recorded for 10% uncertainties. These findings are relevant to the large body of studies involving experimentally based modeling and analysis of vascular tissues. The impact of uncertainties on calibrated constitutive parameters is significant in context of studies that use constitutive parameters to draw conclusions about the underlying microstructure of vascular tissues, their growth and remodeling processes, and aging and disease states. The propagation of uncertainties into the predictions of biophysical parameters, e.g., force, luminal pressure, and wall stresses, is of practical importance in the design and execution of clinical devices and interventions. Furthermore, insights provided by the present findings may lead to more robust parameters identification techniques, and serve as selection criteria in the trade-off between model complexity and sensitivity.

Comparative study of variations in mechanical stress and strain of human blood vessels: mechanical reference for vascular cell mechano-biology

The diseases of human blood vessels are closely associated with local mechanical variations. A better understanding of the quantitative correlation in mechanical environment between the current mechano-biological studies and vascular physiological or pathological conditions in vivo is crucial for evaluating numerous existing results and exploring new factors for disease discovery. In this study, six representative human blood vessels with known experimental measurements were selected, and their stress and strain variations in vessel walls under different blood pressures were analyzed based on nonlinear elastic theory. The results suggest that conventional mechano-biological experiments seeking the different biological expressions of cells at high/low mechanical loadings are ambiguous as references for studying vascular diseases, because distinct "site-specific" characteristics appear in different vessels. The present results demonstrate that the inner surface of the vessel wall does not always suffer the most severe stretch under high blood pressures comparing to the outer surface. Higher tension on the outer surface of aortas supports the hypothesis of the outside-in inflammation dominated by aortic adventitial fibroblasts. These results indicate that cellular studies at different mechanical niches should be "disease-specific" as well. The present results demonstrate considerable stress gradients across the wall thickness, which indicate micro-scale mechanical variations existing around the vascular cells, and imply that the physiological or pathological changes are not static processes confined within isolated regions, but are coupled with dynamic cell behaviors such as migration. The results suggest that the stress gradients, as well as the mechanical stresses and strains, are key factors constituting the mechanical niches, which may shed new light on "factor-specific" experiments of vascular cell mechano-biology.

Multi-objective optimisation of material properties and strut geometry for poly(L-lactic acid) coronary stents using response surface methodology

Coronary stents for treating atherosclerosis are traditionally manufactured from metallic alloys. However, metal stents permanently reside in the body and may trigger undesirable immunological responses. Bioresorbable polymer stents can provide a temporary scaffold that resorbs once the artery heals but are mechanically inferior, requiring thicker struts for equivalent radial support, which may increase thrombosis risk. This study addresses the challenge of designing mechanically effective but sufficiently thin poly(L-lactic acid) stents through a computational approach that optimises material properties and stent geometry. Forty parametric stent designs were generated: cross-sectional area (post-dilation), foreshortening, stent-to-artery ratio and radial collapse pressure were evaluated computationally using finite element analysis. Response surface methodology was used to identify performance trade-offs by formulating relationships between design parameters and response variables. Multi-objective optimisation was used to identify suitable stent designs from approximated Pareto fronts and an optimal design is proposed that offers comparable performance to designs in clinical practice. In summary, a computational framework has been developed that has potential application in the design of high stiffness, thin strut polymeric stents.

Elucidating the role of graft compliance mismatch on intimal hyperplasia using an ex vivo organ culture model

There is a growing clinical need to address high failure rates of small diameter (<6 mm) synthetic vascular grafts. Although there is a strong empirical correlation between low patency rates and low compliance of synthetic grafts, the mechanism by which compliance mismatch leads to intimal hyperplasia is poorly understood. To elucidate this relationship, synthetic vascular grafts were fabricated that varied compliance independent of other graft variables. A computational model was then used to estimate changes in fluid flow and wall shear stress as a function of graft compliance. The effect of compliance on arterial remodeling in an ex vivo organ culture model was then examined to identify early markers of intimal hyperplasia. The computational model prediction of low wall shear stress of low compliance grafts and clinical control correlated well with alterations in arterial smooth muscle cell marker, extracellular matrix, and inflammatory marker staining patterns at the distal anastomoses. Conversely, high compliance grafts displayed minimal changes in fluid flow and arterial remodeling, similar to the sham control. Overall, this work supports the intrinsic link between compliance mismatch and intimal hyperplasia and highlights the utility of this ex vivo organ culture model for rapid screening of small diameter vascular grafts. STATEMENT OF SIGNIFICANCE: We present an ex vivo organ culture model as a means to screen vascular grafts for early markers of intimal hyperplasia, a leading cause of small diameter vascular graft failure. Furthermore, a computational model was used to predict the effect of graft compliance on wall shear stress and then correlate these values to changes in arterial remodeling in the organ culture model. Combined, the ex vivo bioreactor system and computational model provide insight into the mechanistic relationship between graft-arterial compliance mismatch and the onset of intimal hyperplasia.