Enhanced Fenton-like catalysis by iron-based metal organic frameworks for degradation of organic pollutants

Temperature-modulated morphological changes in MIL-88B(Fe)-derived iron-based materials triggering generation of the peroxymonosulfate nonradical pathway to degrade carbamazepine: The key role of iron nanoparticles and CN

Temperature modulation of the synthesis process of MOF-derived composites is not well understood for changes in the peroxymonosulfate catalytic domain. This study synthesized a carbon-based nitrogen-doped (MN@C) MOF-derived composite catalyst derived from MIL-88B(Fe) (Materials Institute Lavoisier) by modulating temperature changes and calcination. Combined with density-functional theory calculations (DFT) analyses showed that changes in iron nanoparticles (FeNP) and CN content caused the alterations of the degradation pathways. MN@C-9 exhibited outstanding activation performance (100 % carbamazepine (CBZ) removal within 10 min). The system maintained efficient operation in different aqueous environments and a wide pH range and demonstrated efficient removal of many pollutants typical of pharmaceuticals and personal care products (PPCPs). After comprehensively analyzing the results of liquid chromatography mass spectrometry (LC-MS) and toxicity prediction, the possible degradation pathways were reasonably speculated, and the toxicity of the byproducts was greatly reduced. This study provides a potential and efficient catalyst preparation strategy for water purification.

Construction of stable photo-Fenton system with efficient removal capability of ciprofloxacin by accelerating in-situ photoreduction of Fe3+ in MIL-100(Fe)

Well-dispersed MIL-100(Fe) nanoparticles were synthesized under mild conditions and used to construct a photo-Fenton system (VMH system) with the assistance of visible-light irradiation and hydrogen peroxide. In such a VMH system, the MIL-100(Fe) has a high specific surface area and provides numerous Fe3+ active sites, thus accelerating the reaction of Fe3+ with photo-generated electrons under visible-light irradiation and generates Fe2+, and then the acquired Fe2+ can activate H2O2 to generate ⋅OH, accompanying with the oxidation of Fe2+ to Fe3+. Hence, the in-situ recycling of Fe2+/Fe3+ promotes the generation of ·OH, thus making the VMH system exhibits promising photocatalytic activity. The removal rate of ciprofloxacin in the VMH system is as high as 95.2% within 120 min photo-Fenton reaction, which is about 26 times higher than that of the Visible light/MIL-100(Fe) system. Moreover, the VMH system also exhibits strong degradation ability to other typical antibiotics, such as tetracycline, norfloxacin and cephalexin, and maintains high cyclic stability, revealing great practical application potential in the purification of antibiotic wastewater.

Nitro-functionalization on MIL-53(Fe) for PCMX degradation: Elevating Fenton-like catalytic propelled by abundant reaction sites and iron cycle

To address the issue of excessive residues of 4-chloro-3,5-dimethylphenol (PCMX) in the water environment. In a one-step solvothermal process, iron-based metal-organic frameworks (Fe-MOFs) material MIL-53(Fe) undergoes a synthetic modification strategy. 2-Nitroterephthalic acid as an organic ligand reacted with Fe3+ in a solvothermal process lasting 18 h to yield the nitro-functionalized MIL-53(Fe)-NO2(18h). The objective was to augment the abundance of Fe central unsaturated coordination sites (Fe CUCs) and expedite the Fe(III)/Fe(II) redox cycle, thereby enhancing the heterogeneous Fenton-like treatment capability of pollutants. MIL-53(Fe)-NO2(18h) has excellent hydrogen peroxide (H2O2) catalytic activity and PCMX degradation across a broad pH spectrum (4.0∼8.0). Almost complete removal of PCMX was achieved within 30 min, while pseudo-first-order kinetic rate constants (kobs) increased 4.37 times over MIL-53(Fe). The confirmation of increased Fe CUCs abundance in MIL-53(Fe)-NO2(18h) was achieved through Lewis acidity, oxygen vacancies (OVs) signals, and Fe-O coordination characterization results. Density functional theory (DFT) calculations revealed that Fe CUCs in MIL-53(Fe)-NO2(18h) exhibits heightened affinity for H2O2 adsorption, showcasing stronger charge transfer and enhanced H2O2 dissociation ability. The Fe(III)/Fe(II) redox cycle, a driving force of Fenton-like reactions, was notably improved in the nitro-modified materials. These enhancements significantly expedited the Fenton-like process, resulting in the generation of increased amounts of reactive oxygen species (ROSs), with hydroxyl radicals (OH·) being pivotal components in degradation. The MIL-53(Fe)-NO2(18h)/H2O2 system has demonstrated versatility in treating a variety of emerging contaminants, achieving removal efficiencies exceeding 99.7% for other antibiotics and endocrine disruptors within 60 min. Furthermore, MIL-53(Fe)-NO2(18h) demonstrated outstanding reusability and adaptability in actual water environments. This study introduces a straightforward and environmentally friendly strategy for remediating environmental pollution using Fe-MOF-catalysed heterogeneous Fenton-like technology.

Electron cycling mechanism in Fe/Mn DSAzyme accelerates BPA degradation and nanoenzyme regeneration

Peroxidase-like (POD-like) as a kind of new Fenton-like catalyst can effectively activate H2O2 to degrade organic pollutants in water, but improving the catalytic activity and stability of POD-like remains a challenging task. Here, we synthesized a novel dual single-atom nanoenzyme (DSAzyme) FeMn/N-CNTs with Fe-N4 and Mn-N4 bimetallic single-atom active centers by mimicking the active centers of natural enzymes and taking advantage of the synergistic effect between the dual metals. FeMn/N-CNTs DSAzyme showed significantly enhanced POD-like activity compared to monometallic-loaded Fe/N-CNTs and Mn/N-CNTs. Within the FeMn/N-CNTs/H2O2 system, bisphenol A (BPA) could be removed 100 % within 20 min. DFT calculations show that Mn-N4 in FeMn/N-CNTs can readily adsorb negatively charged BPA molecules and capture electrons. Meanwhile, Fe-N4 sites can easily adsorb H2O2 molecules, leading to their activation and splitting into strongly oxidizing hydroxyl radicals (·OH). Throughout this process, electrons are continuously recycled in BPA → Mn-N4 → Fe-N4 → H2O2, effectively promoting the regeneration of Fe2+. Practical studies on wastewater and cycling experiments have demonstrated the great potential of this method for remediating water environments.

The Z-Scheme MIL-88B(Fe)/BiOBr Heterojunction Promotes Fe(III)/Fe(II) Cycling and Photocatalytic-Fenton-Like Synergistically Enhances the Degradation of Ciprofloxacin

The Z-scheme MIL-88B/BiOBr (referred to as MxBy, whereas x and y are the mass of MIL-88B(Fe) and BiOBr) heterojunction photocatalysts are successfully prepared by a facile ball milling method. By adding low concentration H2O2 under visible light irradiation, the Z-scheme heterojunction and photocatalytic-Fenton-like reaction synergistically enhance the degradation and mineralization of ciprofloxacin (CIP). Among them, M50B150 showed efficient photodegradation efficiency and excellent cycling stability, with 94.6% removal of CIP (10 mg L-1) by M50B150 (0.2 g L-1) under 90 min of visible light. In the MxBy heterojunctions, the rapid transfer of photo-generated electrons not only directly decomposed H2O2 to generate ·OH, but also improved the cycle of Fe3+/Fe2+ pairs, which facilitated the reaction with H2O2 to generate ·OH and ·O2 - radicals. In addition, the effects of photocatalyst dosages, pH of CIP solution, and coexisting substances on CIP removal are systematically investigated. It is found that the photocatalytic- Fenton-like reaction can be carried out at a pH close to neutral conditions. Finally, the charge transfer mechanism of the Z-scheme is verified by electron spin resonance (ESR) signals. The ecotoxicity of CIP degradation products is estimated by the T.E.S.T tool, indicating that the constructed photocatalysis-Fenton-like system is a green wastewater treatment technology.

Pyrazine-based iron metal organic frameworks (Fe-MOFs) with modulated O-Fe-N coordination for enhanced hydroxyl radical generation in Fenton-like process

Rational design of coordination environment of Fe-based metal-organic frameworks (Fe-MOFs) is still a challenge in achieving enhanced catalytic activity for Fenten-like advanced oxidation process. Here in, novel porous Fe-MOFs with modulated O-Fe-N coordination was developed by configurating amino terephthalic acid (H2ATA) and pyrazine-dicarboxylic acid (PzDC) (Fe-ATA/PzDC-7:3). PzDC ligands introduce pyridine-N sites to form O-Fe-N coordination with lower binding energy, which affect the local electronic environment of Fe-clusters in Fe-ATA, thus decreased its interfacial H2O2 activation barrier. O-Fe-N coordination also accelerate Fe(II)/Fe(III) cycling of Fe-clusters by triggering the reactive oxidant species mediated Fe(III) reduction. As such, Fe-ATA/PzDC-7:3/H2O2 system exhibited excellent degradation performance for typical antibiotic sulfamethoxazole (SMX), in which the steady-state concentration of hydroxyl radical (OH) was 1.6 times higher than that of unregulated Fe-ATA. Overall, this study highlights the role of O-Fe-N coordination and the electronic environment of Fe-clusters on regulating Fenton-like catalytic performance, and provides a platform for precise engineering of Fe-MOFs.

Construction of core-shell magnetic metal-organic framework composites Fe3O4@MIL-101(Fe, Co) for degradation of RhB by efficiently activating PMS

Low catalytic efficiency and catalyst recovery are the key factors limiting the practical application of advanced oxidation processes. In this work, a core-shell magnetic nanostructure Fe3O4@MIL-101(Fe, Co) was prepared via a simple solvothermal method. The core-shell structure and magnetic recovery performance were characterized by various technologies. The results of dye degradation experiments proved that within 10 minutes, the Fe3O4@MIL-101(Fe, Co)/PMS system can degrade more than 95% of 10 mg per L Rhodamine (RhB) at an initial pH of 7, which possesses higher catalytic activity than the Fe3O4/PMS system and the MIL-101(Fe, Co)/PMS system. The effects of initial solution pH and coexisting anions in water on the degradation of RhB were further discussed. The results showed that Fe3O4@MIL-101(Fe, Co) displayed excellent degradation efficiency in a wide pH range of 3-11 and capability of resisting coexisting anions. It is worth mentioning that after five cycles, the RhB removal rate can still be maintained at over 90% after 10 minutes of reaction. Free radical quenching experiments were further studied, confirming that ˙OH and SO4-˙ were involved in the degradation of RhB, while the dominating active free radical was SO4-˙. The possible reaction mechanism of the RhB degradation process was also inferred.

AgAu-modified quasi-MIL-53 hybrid nanozymes with triple enzyme-like activities for boosting biocatalytic disinfection

Metal-organic frameworks (MOFs) have great potential for combating pathogenic bacterial infections and are expected to become an alternative to antibiotics. However, organic linkers obstruct and saturate the inorganic nodes of MOF structures, making it challenging to utilize the applied potential of metal centers. Here, we combined controlled ligand decarboxylation with noble metal nanoparticles to rationally remodel MIL-53, resulting in a hybrid nanozyme (AgAu@QMIL-53, AAQM) with excellent multiple enzyme-like activities that both eradicate bacteria and promote diabetic wound healing. Specifically, benefitting from oxidase (OXD)-like and peroxidase (POD)-like activities, AAQM converts oxygen (O2) and hydrogen peroxide (H2O2) into superoxide anion radicals (O2-) and hydroxyl radicals (OH) to eradicate bacteria. In in vitro antibacterial experiments, AAQM exhibited favorable killing efficacy against Pseudomonas aeruginosa (P. aeruginosa) and methicillin-resistant Staphylococcus aureus (MRSA) (>99 %). Notably, due to its superoxide (SOD)-like activity and outstanding reactive nitrogen species (RNS) elimination capacity, AAQM can produce adequate O2 and alleviate oxidative stress in diabetic wounds. Benefiting from the rational modification of MIL-53, the synthesized hybrid nanozyme can effectively kill bacteria while alleviating oxidative stress and ultimately promote infected diabetic wound healing. Overall, this biomimetic enzyme-catalyzed strategy will bring enlightenment to the design of self-antibacterial agents for efficient disinfection and wound healing simultaneously.

FeCu bimetallic metal organic frameworks photo-Fenton synergy efficiently degrades organic pollutants: Structure, properties, and mechanism insight

The high ion leaching, low photogenerated charge separation efficiency, and slow metal valence cycling of Fe-based metal organic frameworks (MOFs) have limited their application in the deep treatment of organic pollutants. Herein, FeCu bimetallic MOFs (FeCuBDC) were synthesized using a modified solvothermal method, and a coupled photo-Fenton degradation system was successfully constructed. Degradation performance tests showed that FeCuBDC could efficiently degrade 99.3% ± 0.1% of 50 mg/L phenol within 40 min. The reaction rate constants of the photo-Fenton system were 11.0 and 64.7 times higher than those of the single Fenton reaction and photocatalysis, respectively. FeCuBDC also exhibits good cycling stability, degradation generalization, and excellent photoelectric catalytic properties. Such a considerable enhancement in the overall performance pertains to the following. First, the introduction of Cu into Fe-MOFs not only improves the crystallinity and stability, but also reduces the band gap value, increases the absorption capacity of visible light, and promotes the generation of photogenerated carriers. Second, the FeCu in MOFs are all mixed valence. Initially, the high-valence FeCu captures photogenerated electrons and promotes photogenerated charge separation and transfer. Then, the low-valence FeCu adsorbs and decomposes H2O2, accelerating the valence cycling of the bimetallic sites. The core of the reaction mechanism is that FeCuBDC effectively promotes the photo-Fenton synergy.

Dramatic change in the properties of magnetite-modified MOF particles depending on the synthesis approach

Iron-containing metal-organic frameworks are promising Fenton catalysts. However, the absence of additional modifiers has proven difficult due to the low reaction rates and the inability to manipulate the catalysts. We hypothesize that the production of iron oxide NPs in the presence of a metal-organic framework will increase the rate of the Fenton reaction and lead to the production of particles that can be magnetically manipulated without changing the structure of the components. A comprehensive approach lead to a metal organic framework using the example of MIL-88b (Materials of Institute Lavoisier) modified with iron oxides NPs: formulation of iron oxide in the presence of MIL-88b and vice versa. The synthesis of MIL-88b consists of preparing a complexation compound with the respective structure and addition of terephthalic acid. The synthesis of MIL-88b facilitates to control the topology of the resulting material. Both methods for composite formulation lead to the preservation of the structure of iron oxide, however, a more technologically complex approach to obtaining MIL-88b in the presence of Fe3O4 suddenly turned out to be the more efficient for the release of iron ions.

Electronic structure modulation of iron sites with fluorine coordination enables ultra-effective H2O2 activation

Electronic structure modulation of active sites is critical important in Fenton catalysis as it offers a promising strategy for boosting H2O2 activation. However, efficient generation of hydroxyl radicals (•OH) is often limited to the unoptimized coordination environment of active sites. Herein, we report the rational design and synthesis of iron oxyfluoride (FeOF), whose iron sites strongly coordinate with the most electronegative fluorine atoms in a characteristic moiety of F-(Fe(III)O3)-F, for effective H2O2 activation with potent •OH generation. Results demonstrate that the fluorine coordination plays a pivotal role in lowering the local electron density and optimizing the electronic structures of iron sites, thus facilitating the rate-limiting H2O2 adsorption and subsequent peroxyl bond cleavage reactions. Consequently, FeOF exhibits a significant and pH-adaptive •OH yield (~450 µM) with high selectivity, which is 1 ~ 3 orders of magnitude higher than the state-of-the-art iron-based catalysts, leading to excellent degradation activities against various organic pollutants at neutral condition. This work provides fundamental insights into the function of fluorine coordination in boosting Fenton catalysis at atomic level, which may inspire the design of efficient active sites for sustainable environmental remediation.

Recent advances in ultrasound-Fenton/Fenton-like technology for degradation of aqueous organic pollutants

Organic pollutants in water are a serious problem because of their widespread presence, harming the ecosystem and human health. Of the commonly used advanced oxidation processes, a hybrid of ultrasound and the Fenton/Fenton-like technology has received increasing attention in treatment of aqueous organic pollutants. This hybrid is effective in degradation of organic pollutants, but its application has not been summarised. Herein, first, the application and influencing factors of this hybrid technology for organic pollutants degradation are introduced. Second, the mechanism of its action is discussed. Third, the current challenges and future perspectives associated with this technology are proposed. This review provides valuable information regarding this technology, deepens the understanding of its mechanisms of organic pollutants degradation and provides a reference for its use in treatment of aquatic environments.

Efficient spatial separation of charge carriers over Sv-ZnIn2S4/NH2-MIL-88B(Fe) S-scheme heterojunctions for enhanced photocatalytic H2 evolution and antibiotics removal performance

The exploration of highly efficient sunlight-assisted photocatalyst for photodegradation of organic contaminants or energy conversion is strongly encouraged. In this work, we designed a novel three-dimensional spindle-like Sv-ZIS@NMFe heterojunction made of amino functionalized NH2-MIL-88B(Fe) (NMFe) and ZnIn2S4 nanosheets with abundant sulfur vacancies (Sv-ZIS). The structural properties of NMFe materials, such as a clearly defined system of pores and cavities, were retained by the Sv-ZIS@NMFe composites. Additionally, the incorporation of sulfur vacancies, -NH2 functional groups, and well-matched energy level positions led to various synergistic effects that considerably enhanced internal electron transformation and migration, as well as improved adsorption performance. Consequently, under visible light irradiation, the optimized sample exhibited superior hydrogen production activity and tetracycline hydrochloride photodegradation performance. At last, density functional theory calculations was used to further elucidated the possible photoreactivity mechanism. This study demonstrates that the Sv-ZIS@NMFe heterojunction materials formed by ZnIn2S4 with suitable sulfur vacancies and amino functionalized Fe-MOFs have promising applications in photocatalysis.

Fe-pillared montmorillonite functionalized chitosan/gelatin foams for efficient removal of organic pollutants by integration of adsorption and Fenton degradation

A Fe-pillared montmorillonite (Fe-MMT) functionalized bio-based foam (Fe-MMT@CS/G) was developed by using chitosan (CS) and gelatin (G) as the matrix for high-efficiency elimination of organic pollutants through the integration of adsorption and Fenton degradation. The results showed that the mechanical properties of as-obtained foam were strengthened by the addition of certain amounts of Fe-MMT. Interestingly, Fe-MMT@CS/G displayed efficient adsorption ability for charged pollutants under a wide range of pH. The adsorption processes of methyl blue (MB), methylene blue (MEB) and tetracycline hydrochloride (TCH) on Fe-MMT@CS/G were well described by the Freundlich isotherm model and pseudo-second-order kinetic model. The maximum adsorption capacities were 2208.24 mg/g for MB, 1167.52 mg/g for MEB, and 806.31 mg/g for TCH. Electrostatic interactions, hydrogen bonding and van der Waals forces probably involved the adsorption process. As expected, this foam could exhibit better removal properties toward both charged and uncharged organic pollutants through the addition of H2O2 to trigger the Fenton degradation reaction. For non-adsorbable and uncharged bisphenol A (BPA), the removal efficiency was dramatically increased from 1.20 % to 92.77 % after Fenton degradation. Additionally, it presented outstanding recyclability. These results suggest that Fe-MMT@CS/G foam is a sustainable and efficient green material for the alleviation of water pollution.

Tuning Ni-Pyrazolate Frameworks by Post-Synthetic Fe-Incorporation for Oxidase-Mimicking H2 O2 Activation

The introduction of iron ionic sites by metal exchange of defective homometallic nickel pyrazolate frameworks generates non-precious, Earth-abundant, first-row heterometallic Fe/Ni-pyrazolate frameworks. The Fe incorporation at the Ni nodes of the framework allows to control the hydrogen peroxide activation, minimizing its decomposition and O2 liberation, occurring at the homometallic Ni nodes. The generation of Fe-OH reactive oxygen species at the heterometallic Fe/Ni nodes is demonstrated by the higher activity in the proof-of-concept oxidation of 1-phenylethanol to acetophenone in an aqueous medium.

Effective photocatalytic degradation of amphotericin B and naproxen from aqueous solutions using carbon quantum dots combined in MIL-88B(Fe) under visible light

A photocatalytic adsorbent composed of carbon dots (CD) embedded in a metal-organic framework (MOF) of MIL-88 B(Fe) was prepared by solvothermal technique. The synthesized CD@MIL-88 B(Fe) was characterized by different X-ray-based microscopic and spectroscopic methods, as well as electrochemical impedance spectroscopy, UV-Vis, FT-IR, DRS, TGA, and photoluminescence (PL) analysis. The prepared adsorbent showed a remarkable photocatalytic activity for eliminating amphotericin B (AmB) and naproxen (Nap) from aqueous solutions under visible light, reaching up to 92% and 90% removal, respectively, with an RSD value of around 5%. The parameters affecting the degradation process of pharmaceuticals were investigated. The optimal conditions for the degradation process were determined, including pH values (3 and 4 for AmB and Nap), photocatalyst concentration (0.2 g L-1), and H2O2 concentration (40-50 mM). Reactive oxidative species were also identified (·OH, ·O2) by examination of different scavengers. The adsorption isotherm and kinetic studies reveal that the synthesized photocatalyst exhibits dual functionality as an effective adsorbent (with maximum adsorption capacities of 42.5 and 121.5 mg g-1 for AmB and Nap) and a photocatalytic agent for removal purposes.

Binary Metal-Oxide Active Sites Derived from Cu-Doped MIL-88 with Enhanced Electroactivity for Nitrate Reduction

Nitrate-to-ammonia electrochemical conversion is important for decreasing water pollution and increasing the production of valuable ammonia. However, achieving high ammonium production without undesirable byproducts is difficult. Cu-doped MIL-88-derived bimetallic oxide catalysts with electrocatalytically active Fe-O-Cu bridges, which have high NO3- adsorption energy and facilitate N-intermediate hydrogenation, are developed for NH4+ production. Cu doping promotes hybridization between the O 2p of NO3- and Fe-Cu 3d, facilitating the adsorption and reduction of NO3- with a low Tafel slope (62.1 mV dec-1) and high ammonia yield (1698.8 μg·h-1·cm-2). The cathode efficiency is stable for seven cycles. Cu adjacent to Fe sites inhibits hydrogen evolution, promotes NO3- adsorption, and decreases the intermediate adsorption energy barrier. This study provides new opportunities for fabricating diverse binary metal oxides with new interfaces as efficient cathode materials for selective electroreduction.

Sulfur-decorated Fe/C composite synthesized from MIL-88A(Fe) for peroxymonosulfate activation towards tetracycline degradation: Multiple active sites and non-radical pathway dominated mechanism

Peroxymonosulfate (PMS)-mediated advanced oxidation processes gain growing attention in degrading antibiotics (e.g., tetracycline (TC)) in wastewater for their high capacity and relatively low cost, while designing efficient catalysts for PMS activation remains a challenge. In this study, a sulfur-doped Fe/C catalyst (Fe@C-S) synthesized from iron metal-organic frameworks (Fe-MOFs) was developed for PMS activation towards TC removal. Under optimal conditions, the TC removal efficiency of Fe@C-S150/PMS system within 40 min was 91.2%. Meanwhile, the k value for Fe@C-S150/PMS system (0.2038 min-1) was 3.36-fold as high as the S-free Fe@C-based PMS system. Also, Fe@C-S150/PMS system showed high robustness in different water matrices. Further studies found that the TC degradation mechanism was mainly ascribed to the non-radical pathway (1O2 and electron transfer). Fe nanoparticles, S and CO groups on the catalyst all participated in the generation of reactive oxygen species (ROS). Besides, S species could enhance the Fe2+/Fe3+ redox cycle and accelerate the electron transfer process. This work highlights the critical role of S in enhancing the catalytic performance of Fe/C-based catalysts for PMS activation, which would provide meaningful insights into the design of high-performance PMS activators for the sustainable remediation of emerging contaminants-polluted water bodies.

Simple ultrasonic integration of shapeable, rebuildable, and multifunctional MIL-53(Fe)@cellulose composite for remediation of aqueous contaminants

Metal-organic frames (MOFs) have been recognized as one of the best candidates in the remediation of aqueous contaminants, while the fragile powder shape restricts the practical implementation. In this work, a shapeable, rebuildable, and multifunctional MOF composite (MIL-53@CF) was prepared from MIL-53 (Fe) and cellulose fiber (CF) using a simple ultrasonic method for adsorption and photocatalytic degradation of organic pollutants in wastewater. The results showed MIL-53(Fe) crystals were uniformly growth on CF surfaces and bonded with surface nanofibrils of CF through physical crosslinking and hydrogen bonding. Because of the high bonding strength, the MIL-53@CF composite exhibited an excellent compressive strength (3.53 MPa). More importantly, the MIL-53@CF composite was rebuildable through mechanical destruction followed by re-ultrasonication, suggesting the excellent reusability of MIL-53@CF for water remediation. The MIL-53@CF composite also had high adsorption capacities for methyl orange (884.6 mg·g-1), methylene blue (198.3 mg·g-1), and tetracycline (106.4 mg·g-1). MIL-53@CF composite could degrade TC through photocatalysis. The photocatalytic degradation mechanism was attributed to the Fe(II)/Fe(III) transform cycle reaction of MIL-53 crystal located on MIL-53@CF. Furthermore, the mechanical property and remoldability of MIL-53@CF composite increased its practicability. Comprehensively, MIL-53@CF composite provided a possible strategy to practically apply MOF in the remediation of aqueous contaminants.

Stability performance analysis of Fe based MOFs for peroxydisulfates activation to effectively degrade ciprofloxacin

Fe-based metal-organic frameworks (MOFs) show high activity toward the activation of peroxodisulfate (PDS) for the removal of organic micropollutants (OMPs) in wastewater treatment. However, there is a phenomenon of Fe ion dissolution in the Fe-based MOFs' active PDS system, and the reasons and influencing factors that cause Fe ion dissolution are poorly understood. In this study, we synthesized four types of Fe-based MOFs and confirmed their crystal structure through characterization. All types of Fe-based MOFs were found to activate PDS and form sulfate radicals (SO4 -), which effectively remove OMPs in wastewater. During the process of Fe-based MOFs activating PDS for CIP removal, activated species, oxidant reagent, and pH negatively impact the stability performance of the MOFs' structure. The coordination bond between Fe atom and O atom can be attacked by water molecules, free radicals, and H+, causing damage to the crystal structure of MOFs. Additionally, Fe (II)-MOFs exhibit the best stability performance, due to the enhanced bond energy of the coordination bond in MOFs by the F ligands. This study summarizes the influencing factors of Fe-based MOFs' damage during PDS activation processes, providing new insights for the future development of Fe-based MOFs.

Effects and Mechanisms of Cu Species in Fe-MOFs on Fenton-Like Catalytic Activity and Stability

Fe-based MOFs (Fe-MOFs) are deemed promising Fenton-like catalysts due to their well-developed pores and accessible active sites. However, their inferior catalytic activity, iron leaching, and low H₂O₂ utilization always hinder their application as Fe-based MOF catalysts. In this work, we manipulated the structure of Fe-oxo nodes in MIL-88B(Fe) via a Cu^I species substitution method, affording a mixed-valence (Cu-incorporated Fe-MOFs) with highly improved Fenton-like performance. It is found that the Cu^I serves as a shuttle to promote transfer between Fe^II/Fe^III, inducing the formation of a larger amount of stable Fe^II sites, which was proven by experimental and DFT calculation results. A linear relationship was observed for the Fenton-like performance and the amount of Cu^I species for the catalysts. The corresponding value of the ^•OH formation is 2.17 eV for Cu-incorporated MIL-88B(Fe), which is significantly lower than that of MIL-88B(Fe) (2.69 eV). Meanwhile, the enriched Cu^I species suppress Fe species leaching during the catalytic reaction. The Fe-ion leakage of 0.4Cu@MIL-88B is very tiny (0.01-0.03 mg/L), significantly less than that of MIL-88B (2.00-3.02 mg/L). At the same time, H₂O₂ utilization for 0.4Cu@ MIL-88B(Fe) is 88%, which is almost 4.4 times that of pure MIL-88B(Fe). This work provides insights into the rational design of Fe-MOFs as promising Fenton-like catalysts for wastewater treatment.

Fabrication and optimization of paper chips from calcinated Fe-MOFs for rapid and in situ visual detection of tetracyclines in water environments

Antibiotics such as tetracyclines (TCs) have become a major threat to ecosystem safety and human health, as their abuse has caused the occurrence and proliferation of antibiotic-resistant bacteria and genes. Currently, there is still a lack of convenient in situ methods for the detection and monitoring of TC pollution in actual water systems. This research reports a paper chip based on the complexation of iron-based metal organic frameworks (Fe-MOFs) and TCs for rapid and in situ visual detection of representative oxytetracycline (OTC) pollution in water environments. The optimized complexation sample NH₂-MIL-101(Fe)- 350 obtained by calcination at 350 °C exhibited the highest catalytic activity and was then used for paper chip fabrication by printing and surface modification. Notably, the paper chip demonstrated a detection limit as low as 17.11 nmol L^-1 and good practicability in reclaimed water, aquaculture wastewater, and surface water systems, with OTC recovery rates of 90.6-111.4%. More importantly, the presence of dissolved oxygen (9.13-12.7 mg L^-1), chemical oxygen demand (0.52-12.1 mg L^-1), humic acid (< 10 mg L^-1), Ca²⁺, Cl^-, and HPO₄^2- (< 0.5 mol L^-1) had negligible interference on the detection of TCs by the paper chip. Therefore, this work has developed a promising method for rapid and in situ visual monitoring of TC pollution in actual water environments.

The performance and mechanism of iron-mediated chemical oxidation: Advances in hydrogen peroxide, persulfate and percarbonate oxidation

Many studies have successfully built iron-mediated materials to activate or catalyze Fenton-like reactions, with applications in water and wastewater treatment being investigated. However, the developed materials are rarely compared with each other regarding their performance of organic contaminant removal. In this review, the recent advances of Fenton-like processes in homogeneous and heterogeneous ways are summarized, especially the performance and mechanism of activators including ferrous iron, zero valent iron, iron oxides, iron-loaded carbon, zeolite, and metal organic framework materials. Also, this work mainly compares three O-O bond containing oxidants including hydrogen dioxide, persulfate, and percarbonate, which are environmental-friendly oxidants and feasible for in-situ chemical oxidation. The influence of reaction conditions, catalyst properties and benefits are analyzed and compared. In addition, the challenges and strategies of these oxidants in applications and the major mechanisms of the oxidation process have been discussed. This work can help understand the mechanistic insights of variable Fenton-like reactions, the role of emerging iron-based materials, and provide guidance for choosing appropriate technologies when facing real-world water and wastewater applications.

Use of copper sheet in a solar photo-Fenton-like process applied in the treatment of landfill leachate

It is known that copper can be used as catalyst in photo-Fenton-like process; however, there is a lack of information related with its use in the treatment of landfill leachate (LL) in solar photo-Fenton-like processes. Here, we studied the effect of the mass of a copper sheet, the pH of the solution, and the concentration of LL in the removal of the organic matter present in this water. Before the reaction with landfill leachate, the copper sheet used in the reaction was constituted by Cu⁺ and Cu₂O, respectively. The results showed that in a volume of 0.5 L of a pretreated LL, the higher removal of organic matter resulted using a mass of 2.7 g of the copper sheet, a pH of solution of 5, and a concentration of LL of a 10%, obtaining a final value of C/C₀ of chemical oxygen demand (COD) of 0.34, 0.54, 0.66, and 0.84 for concentrations of 25%, 50%, 75%, and 100%, respectively, and 0.0041, 0.0042, 0.0043, and 0.016 for concentration of 25%, 50%, 75%, and 100%, respectively, of C/C₀ of humic acids. The photolysis on LL at its natural pH using solar UV removes very little humic acid and COD, going from 9.4 to 8.5 and 7.7 Abs₂₅₄ for photolysis and UV + H₂O₂, obtaining 8.6 and 17.6% of removal, respectively, and 2.01 and 13.04% removal of COD, respectively. Copper sheet applied under Fenton-like conditions results in 65.9% removal and an increase of 0.2% for humic acid and COD, respectively. Removal using only H₂O₂ for Abs₂₅₄ and COD was 11.95 and 4.3%, respectively. Raw LL produced a 29.1% inhibition of the biological activated sludge rate after the adjustment to pH 7 and the final process of inhibition was 0.23%.

Co3O4 with upshifted d-band center and enlarged specific surface area by single-atom Zr doping for enhanced PMS activation

In this work, single-atom Zr doping is demonstrated to be an effective strategy to enhance the catalytic performance of Co₃O₄ toward peroxymonosulfate (PMS) by modulating electronic structure and enlarging specific surface simultaneously. The d-band center of Co sites upshifts owing to different electronegativity of Co and Zr in the bonds of Co-O-Zr confirmed by density functional theory calculations, leading to enhanced adsorption energy of PMS and strengthened electron transfer from Co^(II) to PMS. The specific surface area of Zr-doped Co₃O₄ increases by 6 times due to the decrease of crystalline size. Consequently, the kinetic constant of phenol degradation with Zr-Co₃O₄ is 10 times higher than that with Co₃O₄ (0.31 vs. 0.029 min^-1). The relative surface specific kinetic constant of Zr-Co₃O₄ for phenol degradation is still 2.29 times higher than that of Co₃O₄ (0.00660 vs. 0.00286 g m^-2 min^-1). In addition, the potential practical applicability of 8Zr-Co₃O₄ was also confirmed by practical wastewater treatment. This study provides deep insights into modifying electronic structure and enlarging specific surface area to enhance the catalytic performance.

Hydroxyl radicals in natural waters: Light/dark mechanisms, changes and scavenging effects

Hydroxyl radicals (•OH) are the most active, aggressive and oxidative reactive oxygen species. In the natural aquatic environment, •OH plays an important role in the biogeochemistry cycle, biotransformation, and pollution removal. This paper reviewed the distribution and formation mechanism of •OH in aquatic environments, including natural waters, colloidal substances, sediments, and organisms. Furthermore, factors affecting the formation and consumption of •OH were thoroughly discussed, and the mechanisms of •OH generation and scavenging were summarized. In particular, the effects of climate change and artificial work on •OH in the largest natural aquatic environment, i.e., marine environment was analyzed with the help of bibliometrics. Moreover, Fenton reactions make the •OH variation more complicated and should not be neglected, especially in those areas with suspended particles and sediments. Regarding the •OH variation in the natural aquatic environment, more attention should be given to global change and human activities.

Application of Photo-Fenton-Membrane Technology in Wastewater Treatment: A Review

Photo-Fenton coupled with membrane (photo-Fenton-membrane) technology offers great potential benefits in future wastewater treatment because it can not only degrade refractory organics, but also separate different pollutants from water; additionally, it often has a membrane-self-cleaning ability. In this review, three key factors of photo-Fenton-membrane technology, photo-Fenton catalysts, membrane materials and reactor configuration, are presented. Fe-based photo-Fenton catalysts include zero-valent iron, iron oxides, Fe-metal oxides composites and Fe-based metal-organic frameworks. Non-Fe-based photo-Fenton catalysts are related to other metallic compounds and carbon-based materials. Polymeric and ceramic membranes used in photo-Fenton-membrane technology are discussed. Additionally, two kinds of reactor configurations, immobilized reactor and suspension reactor, are introduced. Moreover, we summarize the applications of photo-Fenton-membrane technology in wastewater, such as separation and degradation of pollutants, removal of Cr(VI) and disinfection. In the last section, the future prospects of photo-Fenton-membrane technology are discussed.

Defective iron based metal-organic frameworks derived from zero-valent iron for highly efficient fenton-like catalysis

Introducing crystal defects into iron based metal-organic frameworks (Fe-MOFs) is regarded as a promising strategy to enhance Fenton-like performance. However, developing a facile and effective strategy to construct defective Fe-MOFs as highly efficient Fenton-like catalyst is still a challenge. Herein, MIL-100(Fe) (Def-MIL-100(Fe)) with missing ligands defects was synthesized by a simple heterogeneous reaction using zero-valent iron. The bisphenol A degradation efficiency in the Def-MIL-100(Fe)/H₂O₂ system reached up to 91.26% within 10 min at pH 4 with a low catalyst dosage of 0.05 g/L, while the perfect MIL-100(Fe) has almost no Fenton-like performance. It was observed that missing ligands defects in the Def-MIL-100(Fe) play a key role in the Fenton-like reaction. The missing ligands defects could increase the Lewis acidity for fast H₂O₂ adsorption and accelerate the electron transfer between Fe^II and Fe^III cycling, leading to faster and more·OH generation. Moreover, the missing ligands defects could promote the mass transfer for improving·OH utilization efficiency. This work provides a novel strategy to construct defective Fe-MOFs as highly efficient Fenton-like catalyst to degrade organic pollutants in water.

Catalytic Micromotors as Self-stirring Microreactors for Efficient Dual-mode Colorimetric Detection

A catalytic micromotor-based (MIL-88B@Fe₃O₄) colorimetric detection system which exhibit rapid color reaction for quantitative colorimetry and high-throughput testing for qualitative colorimetry have been successfully developed. Taking the advantages of the micromotor with dual roles (micro-rotor and micro-catalyst), under rotating magnetic field, each micromotor represents a microreactor which have micro-rotor for microenvironment stirring and micro-catalyst for the color reaction. Numerous self-string micro-reactions rapidly catalyze the substance and show the corresponding color for the spectroscopy testing and analysis. Additionally, owing to the tiny motor can rotate and catalyze within microdroplet, a high-throughput visual colorimetric detection system with 48 micro-wells has been innovatively conducted. The system enables up to 48 microdroplet reactions based on micromotors run simultaneously under the rotating magnetic field. Multi-substance, including their species difference and concentration strength, can be easily and efficiently identified by observing the color difference of the droplet with naked eye after just one test. This novel catalytic MOF-based micromotor with attractive rotational motion and excellent catalytic performance not only endowed a new nanotechnology to colorimetry, but also shows hold great potentials in other fields, such as refined production, biomedical analysis, environmental governance etc., since such micromotor-based microreactor can be easily applied to other chemical microreactions.

ZIF-8@Rhodamine B as a Self-Reporting Material for Pollutant Extraction Applications

Herein, we have evaluated the potential of dye-encapsulation as a simple mechanism to self-report the stability of MOFs for pollutant extraction applications. This enabled the visual detection of material stability issues during the selected applications. As proof-of-concept, the zeolitic imidazolate framework (ZIF-8) material was prepared in aqueous medium and at room temperature in the presence of the dye rhodamine B. The total amount of loaded rhodamine B was determined using UV-vis spectrophotometry. The prepared dye-encapsulated ZIF-8 showed a comparable extraction performance with bare ZIF-8 for the removal of hydrophobic endocrine-disrupting phenols, such as 4-tert-octylphenol and 4-nonylphenol, and improved the extraction performance of more hydrophilic endocrine disruptors, such as bisphenol A and 4-tert-butylphenol.

Visible-light-driven iron-based heterogeneous photo-Fenton catalysts for wastewater decontamination: A review of recent advances

Visible-light-driven heterogeneous photo-Fenton process has emerged as the most promising Fenton-derived technology for wastewater decontamination, owing to its prominent superiorities including the potential utilization of clean energy (solar light), and acceleration of ≡Fe(II)/≡Fe(III) dynamic cycle. As the core constituent, catalysts play a pivotal role in the photocatalytic activation of H₂O₂ to yield reactive oxidative species (ROS). To date, all types of iron-based heterogeneous photo-Fenton catalysts (Fe-HPFCs) have been extensively reported by the scientific community, and exhibited satisfactory catalytic performance towards pollutants decomposition, sometimes even exceeding the homogeneous counterparts (Fe(II)/H₂O₂). However, the relevant reviews on Fe-HPFCs, especially from the viewpoint of catalyst-self design are extremely limited. Therefore, this state-of-the-art review focuses on the available Fe-HPFCs in literatures, and gives their classification based on their self-characteristics and modification strategies for the first time. Two classes of representative Fe-HPFCs, conventional inorganic semiconductors of Fe-containing minerals and newly emerging Fe-based metal-organic frameworks (Fe-MOFs) are comprehensively summarized. Moreover, three universal strategies including (i) transition metal (TMs) doping, (ii) construction of heterojunctions with other semiconductors or plasmonic materials, and (iii) combination with supporters were proposed to tackle their inherent defects, viz., inferior light-harvesting capacity, fast recombination of photogenerated carriers, slow mass transfer and low exposure and uneven dispersion of active sites. Lastly, a critical emphasis was also made on the challenges and prospects of Fe-HPFCs in wastewater treatment, providing valuable guidance to researchers for the reasonable construction of high-performance Fe-HPFCs.

Metal-Organic Frameworks as Photocatalysts for Solar-Driven Overall Water Splitting

Metal-organic frameworks (MOFs) have been frequently used as photocatalysts for the hydrogen evolution reaction (HER) using sacrificial agents with UV-vis or visible light irradiation. The aim of the present review is to summarize the use of MOFs as solar-driven photocatalysts targeting to overcome the current efficiency limitations in overall water splitting (OWS). Initially, the fundamentals of the photocatalytic OWS under solar irradiation are presented. Then, the different strategies that can be implemented on MOFs to adapt them for solar photocatalysis for OWS are discussed in detail. Later, the most active MOFs reported until now for the solar-driven HER and/or oxygen evolution reaction (OER) are critically commented. These studies are taken as precedents for the discussion of the existing studies on the use of MOFs as photocatalysts for the OWS under visible or sunlight irradiation. The requirements to be met to use MOFs at large scale for the solar-driven OWS are also discussed. The last section of this review provides a summary of the current state of the field and comments on future prospects that could bring MOFs closer to commercial application.

Steady release-activation of hydrogen peroxide and molecular oxygen towards the removal of ciprofloxacin in the FeOCl/CaO2 system

Difficult storage of hydrogen peroxide (H₂O₂), low production of reactive oxygen species (ROS), and inefficient Fe(II)/Fe(III) recycling limit the application of the Fenton-like process. Calcium peroxide (CaO₂) based iron oxychloride (FeOCl) system was developed for solving these deficiencies, and ciprofloxacin (CIP) was effectively degraded within 20 min treatment. 0.33 mmol/L H₂O₂ and 2.4 mg/L dissolved oxygen (DO) were produced via CaO₂. Quenching experiments and electron paramagnetic resonance results confirmed that hydroxyl radicals (·OH) and superoxide anion (·O₂^-) worked as the main ROS. Density functional theory (DFT) calculations and experimental results suggested that H atoms of H₂O₂ adsorbed on FeOCl favored the activation of H₂O₂ into ·OH and DO into ·O₂^-, and electrophilic Cl and O coordination in FeOCl contributed to the cycle of Fe(II)/Fe(III). ·OH and·O₂^- were responsible for CIP degradation, and toxicity assessments demonstrated that the developed system reduced the hazard of treated solution. Clarity of FeOCl/CaO₂ system triple roles, including H₂O₂ and O₂ production, activation into ROS, and Fe(II)/Fe(III) recycling, facilitates the efficient utilization of O₂ in Fenton-like system.

Hierarchical porous melamine sponge@MIL-101-Fe-NH2 composite as Fenton-like catalyst for efficient and rapid tetracycline hydrochloride removal

Metal-organic frameworks have been investigated in Fenton-like catalysis for tetracycline hydrochloride degradation, a widely used antibiotic which threatens the growth and health of creatures. However, powder phase and absence of large pores limit the materials' degradation performance and application. In this work, a hierarchical macro-meso-microporous composite melamine sponge@MIL-101-Fe-NH₂ was firstly designed and constructed. While the micropores provided plenty of active sites to generate reactive oxygen species, the macropores and mesopores accelerated mass transfer. Besides, MIL-101-Fe-NH₂ particles dispersed on melamine sponge individually, exposing more catalytic sites and avoiding inactivation caused by aggregation compared to powder catalysts. Its catalysis performance for tetracycline hydrochloride degradation was evaluated through changing various influence factors like H₂O₂ concentration, catalyst amount, pH and coexisting ions. Different from the preference of homogenous Fenton catalysts for pH 2-4, the composite displayed the most effective degradation at a subacid environment closer to nature with 77.24% in 30 min. Owing to the synergistic effect of hierarchical porous structure and monodispersed nanoparticles, the composite exhibited faster reaction rate and longer persistence compared to powder MIL-101-Fe-NH₂. Easy recycling and less ion leaching made it advantages for practical application. •OH, •O₂^- and ¹O₂ active species contributed together to the degradation and two main possible degradation pathways were put forward based on 35 detected intermediates.

Fe-Cu binary oxide loaded zeolite as heterogeneous Fenton catalyst for degradation of carbamazepine at near-neutral pH

In this study, Fe-Cu binary oxide was loaded on zeolite (Fe/Cu/zeolite) to be used as heterogeneous Fenton catalyst, and the catalytic degradation of carbamazepine (CBZ) were optimized at near-neutral pH. The results showed that the Fe and Cu oxide, mainly Fe₂O₃, Fe₃O₄, and CuO nanoparticles, were uniformly distributed on the surface of zeolite particles. Under the optimized conditions, Fe/Cu/zeolite could completely degrade CBZ when initial pH ranged from 3 to 7, and the removal efficiency of CBZ still remained above 74% even though the initial pH increased to near 10. After 8 times' repeated use, the Fe/Cu/zeolite exhibited an over 95% removal efficiency of CBZ. The hydroxyl radicals (•OH) were verified to be the main active oxidants by quenching experiments and ESR testing. The XPS of the materials revealed that the high catalytic efficiency was attributed to the synergistic effect of Fe(III)/Fe(II) and Cu(II)/Cu(I) redox cycles. This catalyst can be used for the efficient degradation of organic pollutants in heterogeneous Fenton systems.

Recent developments in MOF and MOF based composite as potential adsorbents for removal of aqueous environmental contaminants

With the growth of globalization which has been the primary cause of water pollution, it is utmost necessary for us living being to have access to clean water for the purpose of drinking, washing and various other useful applications. With the purpose of future security and to restore our ecological balance, it is essential to give much significance towards the removal of unwanted toxic contaminants from our water resources. In this regard adsorptive removal of toxic pollutants from wastewater with porous adsorbent is regarded as one of the most promising way for water decontamination process. Metal organic frameworks (MOFs) comprising of uniformly arranged pores, abundant active sites and containing an easily tunable structure has aroused as a promising material for adsorbent to remove the unwanted contaminants from water sources. The adsorption of pollutants by the different MOFs surface are driven by various interactions including π-π, acid-base, electrostatic and H-bonding etc. On the other hand, the removal of various contaminants by MOFs is influenced by various factors including pH, temperature and initial concentration. In this review we will specifically discuss the adsorptive removal of different organic and inorganic pollutants present in our water systems with the use of MOFs as adsorbent along with the various factors and interaction mechanism manipulating the adsorption behaviour.

Bimetallic Metal-Organic Framework Fe/Co-MIL-88(NH2) Exhibiting High Peroxidase-like Activity and Its Application in Detection of Extracellular Vesicles

Metal-organic frameworks (MOFs) have many attractive features, including tunable composition, rigid structure, controllable pore size, and large specific surface area, and thus are highly applicable in molecular analysis. Depending on the MOF structure, a high number of unsaturated metal sites can be exposed to catalyze chemical reactions. In the present work, we report that using both Co(II) and Fe(III) to prepare the MIL-88(NH₂) MOF, we can produce the bimetallic MOF that can catalyze the conversion of 3,3',5,5″-tetramethylbenzidine (TMB) to a color product through a reaction with H₂O₂ at a higher reaction rate than the monometallic Fe-MIL-88(NH₂). The Michaelis constants (K_m) of the catalytic reaction for TMB and H₂O₂ are 3-5 times smaller, and the catalytic constants (k_cat) are 5-10 times higher than those of the horseradish peroxidase (HRP), supporting ultrahigh peroxidase-like activity. These values are also much more superior to those of the HRP-mimicking MOFs reported previously. Interestingly, the bimetallic MOF can be coupled with glucose oxidase (GOx) to trigger the cascade enzymatic reaction for highly sensitive detection of extracellular vesicles (EVs), a family of important biomarkers. Through conjugation to the aptamer that recognizes the marker protein on EV surface, the MOF can help isolate the EVs from biological matrices, which are subsequently labeled by GOx via antibody recognition. The cascade enzymatic reaction between MOF and GOx enables the detection of EVs at a concentration as low as 7.8 × 10⁴ particles/mL. The assay can be applied to monitor EV secretion by cultured cells and also can successfully detect the different EV quantities in the sera samples collected from cancer patients and healthy controls. Overall, we prove that the bimetallic Fe/Co-MIL-88(NH₂) MOF, with its high peroxidase activity and high biocompatibility, is a valuable tool deployable in clinical assays to facilitate disease diagnosis and prognosis.

Carbon/iron by-product from catalytic methane decomposition as recyclable Fenton catalyst for pollutant degradation

Direct catalytic decomposition of methane (CDM) has been studied as a possible emission-free hydrogen production route for over 100 years. However, the high cost of catalyst regeneration limits its practical applications. Here, we demonstrate that the solid by-product from CDM using Fe ore catalysts comprising carbon nano onions encapsulated with magnetic Fe cores (Fe@C) can serve as efficient and recyclable Fenton catalysts for pollutant degradation. Fe@C/H₂O₂ has better performance than FeSO₄/H₂O₂ at similar Fe concentrations and can be used to decompose various pollutants. Mechanistic studies reveal that graphitic carbon layers and encapsulated Fe⁰ contribute to their high catalytic activity. Further, Fe@C can be easily recovered from an aqueous solution and reused due to the encapsulated magnetic Fe particles. Over three reused cycles, Fe@C/H₂O₂ only yields 1/8 of Fe sludges compared to FeSO₄/H₂O₂, significantly reducing Fe sludge treatment costs. Overall, Fe@C demonstrates excellent application potentials in water and wastewater treatment, making H₂ production via CDM economically more viable.

Fe-O-Zr in MOF for effective photo-Fenton Bisphenol A degradation: Boosting mechanism of electronic transmission

To enhance the efficiency of photogenerated electron transport in the photo-Fenton reaction, we report a Fe-doped UiO-66 containing Fe-O-Zr bonds for the photo-Fenton reaction system. The modulation changes the energy bandgap from 3.89 eV to 2.02 eV, and its absorption edge is red-shifted from the UV region to the visible range. Simultaneously, Fe-O-Zr reduces the redox internal resistance, enhances the photocurrent and catalytic process, and suppresses the compounding of photogenerated electrons and holes. These promote the valence cycling of Fe(III)/Fe(II) in the photo-Fenton reaction. Compared with UiO-66, the hydroxyl radical generation efficiency of this reaction system was increased by 5.8 times (UiO-66: 0.0009 mM/min, FeUiO-1: 0.0053 mM/min). The degradation efficiency of BPA was increased by 100.8 times (UiO-66: 0.0012 min^-1, FeUiO-1: 0.121 min^-1), and the removal rate of TOC also reached 69.55%. The removal rate of BPA was maintained at more than 85% through 5 cycles. The reaction system was able to maintain a removal rate more than 97% at pH:3-9. In the presence of anions, such as Cl^-, SO₄^2-, NO₃^2- (10 mM), the degradation rates of BPA were still above 94%. The catalytic efficiency was 2.02 times higher under natural light than relative to dark conditions. It was demonstrated by EPR and inhibition experiments that the main active species in the reaction were hydroxyl radicals and vacancies. The HOMO energy level and LUMO energy level of the intermediates were analyzed, and the possible degradation pathways of the active species were speculated. Evaluation of the biological toxicity of intermediates demonstrated that the system can effectively detoxify BPA. This investigation provides a reference method to enhance the efficiency of the photo-Fenton reaction of MOFs.

Salicylic acid-based hypoxia-responsive chemodynamic nanomedicines boost antitumor immunotherapy by modulating immunosuppressive tumor microenvironment

The delivery of salicylic acid or its derivatives to tumor tissue in the form of nanomedicine is critical for the studies on their potential synergistic mechanism in tumor therapy and chemoprevention considering the dangerous bleeding in the high-dose oral administration. To deepen the understanding of their role in adjusting immunosuppressive tumor microenvironment (ITM), herein, we firstly developed a hypoxia-sensitive Fe-5,5'-azosalicylic acid nanoscale coordination polymer nanomedicines (FeNCPs) via a "old drugs new tricks" strategy for synergistic chemodynamic therapy (CDT) and remodulation of ITM to elevate antitumor immunotherapy effect. PEGylated FeNCPs could be reductively cleaved to release 5-aminosalicylic acid (5-ASA) and ferric ions by azo-reductase under hypoxic conditions, which could induce tumor cell death by Fenton reaction-catalysis enhanced CDT and 5-ASA-converted carboxylquinone to promote the production of •OH. Meanwhile, cyclooxygenase-2 (COX-2) and its enzymatic product prostaglandin E₂ (PGE₂), as immune negative regulatory molecules, can promote tumor progression and immune tolerance. The released 5-ASA as a COX inhibitor could suppress the expression of PGE₂, and Fe³⁺ was employed to reeducate M2-like tumor-associated macrophages (TAMs) to M1-like phenotype, which could initiate antitumor immune response to reach better antitumor immunotherapy. This work broadens the application of salicylic acid derivatives in antitumor immunotherapy, and provides a new strategy for their "old drugs new tricks". STATEMENT OF SIGNIFICANCE: Cyclooxygenase-2 (COX-2) and its enzymatic product prostaglandin E2 (PGE₂), as immune negative regulatory molecules, facilitate the differentiation of immune cells into immunosuppressive cells to build the immunosuppressive tumor microenvironment, which can promote tumor progression and immune tolerance. Thus, down-regulation of COX-2/PGE₂ expression may be a key approach to tumor treatments. Meanwhile, as a class of inhibitors of COX-2/PGE₂, the potential mechanism of aspirin or 5-aminosalicylic acid has been a mystery in tumor therapy and chemoprevention. To expand the application of aspirin family nanomedicine in biomedicine, herein, we firstly developed a hypoxia-sensitive Fe-5,5'-azosalicylic acid nanoscale coordination polymer nanomedicines via a "old drugs new tricks" strategy for synergistic chemodynamic therapy and remodulation of immunosuppressive tumor microenvironment to elevate antitumor immunotherapy effect.