Efficient adsorbents of nanoporous aluminosilicate monoliths for organic dyes from aqueous solution

Bacterial cellulose based TiO2-CdS nanocomposite gel with enhanced photocatalytic activity for adsorptive degradation of cationic dye

Dye released by industrial is one of the main known pollutants in wastewater, which is harmfully affected to the human health. Adsorptive method by absorbents and photocatalytic degradation technique are advanced technologies to remove dyes from wastewater. However, the single technique mentioned above has imperfections limiting its application. Herein, in order to integrate the two techniques and take both advantages, bacterial cellulose (BC) based titanium dioxide (TiO2)‑cadmium sulfide (CdS) nanocomposite gel was prepared by microwave-assisted solvothermal synthesis. The BC@TiO2-CdS nanocomposite gel was characterized by SEM, EDS, XRD, XPS, Raman spectral and TG, its photocatalytic mechanism was proved by PL. The results showed the TiO2-CdS nanophotocatalyst exhibited binary hierarchical structure and followed the Z-scheme type photocatalytic system. The Z-scheme heterojunction is advantageous for photo-generated charge separation and migration. The photocatalytic performance of BC@TiO2-CdS nanocomposite gel was evaluated by MB degradation under visible light irradiation. Due to synergistic effect of BC matrix and TiO2-CdS, the as-prepared BC@TiO2-CdS nanocomposite gel possesses enhanced photocatalytic activity with 94.47 % removal of methylene blue (MB) after 180 min visible light irradiation. Therefore, this work provides a facile route to fabricate bio-mass based efficient nanophotocatalytic material for pretreating the water pollution.

Porous polymer magnetic adsorbents for dye wastewater treatment

Dye wastewater discharged from industries has caused serious environmental problems. The recent decade has witnessed adsorption technology emerging as an advanced dye wastewater treatment method with great potential Therefore, we fabricated two kinds of magnetic porous adsorbents (HSF and HSVF) with different specific surface areas and activity sites. Both of which exhibit excellent performance with remarkable dye adsorption capacities, especially HSVF. We further investigated their adsorption kinetic and isotherm in detail. Therein, HSVF showed a nice desorption capacity, and it could be recycled rapidly by magnetism, which exhibited the advantages of effective, easy operation, and low cost. In addition, their adsorption kinetic and isotherm were further studied and compared in detail. The results revealed that introducing strong active sites could improve both the adsorption capacity and rate effectively even though sacrificing part of specific surface areas, indicating that active sites might play a dominant role during the dye adsorption process.

Layered by layered construction of three novel ZnCo-LDHs/g-C3N4 for the removal of sunset yellow by adsorption-photocatalytic process

The removal of organic dyes has attracted attention by adsorption-photocatalytic synergetic process in water treatment technology. Three novel ZnCo-LDHs/g-C3N4 were successfully prepared for the first time by layered construction technique through the hydrolysis of triethanolamine in this paper. They exhibited high specific surface area which facilitates the adsorption of sunset yellow (SY) from solution to catalyst surface. All the target pollutant dyes are very effectively removed by the three ZnCo-LDHs/g-C3N4 composites through synergetic effect of adsorption and photocatalysis process under UV irradiation (λ = 365 nm). The order of synergistic degradation effect for SY is as follows: ZnCo-LDHs/g-C3N4-3 (99.6%) > ZnCo-LDHs/g-C3N4-2 (99.5%) > ZnCo-LDHs/g-C3N4-1 (99.3%) > pure g-C3N4 (77.4%) > pure ZnCo-LDHs (44.2.6%) at the initial concentration of 75 mg L-1. ZnCo-LDHs/g-C3N4-3 has the largest k value (0.0284 min-1) in SY degradation, which is 2.8 times that of g-C3N4. ZnCo-LDHs/g-C3N4-3 is a very promising adsorption-photocatalyst for the removal of SY from wastewater. The electron spin resonance experiments demonstrate that OH·, 1O2, and O2- are the dominant active species and oxides SY together. This result demonstrates that the three ZnCo-LDHs/g-C3N4 have practical applications as efficient adsorption-photocatalytic materials and also provides a synergetic strategy for the removal of SY wastewater.

Green synthesize of nano-MOF-ethylcellulose composite fibers for efficient adsorption of Congo red from water

Two novel MOF- ethyl cellulose (EC)- based nanocomposites have been designed and synthesized in water by electrospinning and applied for adsorption of congo red (CR) in water. Nano- Zeolitic Imidazolate Framework-67 (ZIF-67), and Materials of Institute Lavoisier (MIL-88A) were synthesized in aqueous solutions by a green method. To enhance the dye adsorption capacity and stability of MOFs, they have been incorporated into EC nanofiber to prepare composite adsorbents. The performance of both composites in the absorption of CR, a common pollutant in some industrial wastewaters, has then been investigated. Various parameters including initial dye concentration, the dosage of the adsorbent, pH, temperature and contact time were optimized. The results indicated 99.8 and 90.9% adsorption of CR by EC/ZIF-67 and EC/MIL-88A, respectively at pH = 7 and temperature at 25 °C after 50 min. Furthermore, the synthesized composites were separated conveniently and successfully reused five times without significant loss of their adsorption activity. For both composites, the adsorption behavior can be explained by pseudo-second-order kinetics, Intraparticular diffiusion and Elovich models demonstrated that the experimental data well matched to the pseudo-second-order kinetics. Intraparticular diffiusion model showed that the adsorption of CR on EC/ZIF-67 and EC/MIL-88a took place in one and two steps, respectively. Freundlich isotherm models and thermodynamic analysis indicated exothermic and spontaneous adsorption.

Room temperature fabrication of cobalt mullite for the snappy adsorption of cationic and anionic dyes

Cobalt mullite adsorbent for the robust adsorption performance toward Victoria Blue (VB) and Metanil Yellow (MY) is fabricated by the sol-gel method at room temperature using dipropylamine as a structure-directing agent. The synthesized adsorbent is characterized by XRD, FT-IR, and HRTEM. From these analyses, it is found that dipropylamine binds with the alumina and cobalt oxide, which makes it into tetrahedral to octahedral form. This interaction causes the formation of cobalt mullite. It is observed that trigonal alumina and orthorhombic cobalt mullite are interlinked to form a hybrid network. The special feature of adopting this adsorbent for the adsorption of VB and MY is that it has a large amount of Brønsted acid site because of the octahedral coordination of Al and Co. The large availability of acid sites in the framework and hybridization of two different network systems favors robust adsorption. The rate of adsorption (K₂ = 0.00402 g/mg.min for VB and K₂ = 0.004 g/mg.min for MY) and adsorption capacity (Q_e = 102.041 mg/g for VB and Q_e = 19.0406 mg/g for MY) are greater for VB than MY. This may be due to the more steric factor involved in MY than VB. Thermodynamic parameter indicated that the adsorption of VB and MY is spontaneous, endothermic, and increased randomness in the adsorbent-adsorbate interface. The results from the enthalpy value (ΔH° = 65.43 kJ/mol for VB and ΔH° = 44.729 kJ/mol for MY) revealed that the chemisorption is involved in the adsorption process.

Effective Adsorption and Removal of Doxorubicin from Aqueous Solutions Using Mesostructured Silica Nanospheres: Box-Behnken Design Optimization and Adsorption Performance Evaluation

The aim of this study is to evaluate the efficacy of mesoporous silica nanospheres as an adsorbent to remove doxorubicin (DOX) from aqueous solution. The surface and structural properties of mesoporous silica nanospheres were investigated using BET, SEM, XRD, TEM, ζ potential, and point of zero charge analysis. To optimize DOX removal from aqueous solution, a Box-Behnken surface statistical design (BBD) with four times factors, four levels, and response surface modeling (RSM) was used. A high amount of adsorptivity from DOX (804.84 mg/g) was successfully done under the following conditions: mesoporous silica nanospheres dose = 0.02 g/25 mL; pH = 6; shaking speed = 200 rpm; and adsorption time = 100 min. The study of isotherms demonstrated how well the Langmuir equation and the experimental data matched. According to thermodynamic characteristics, the adsorption of DOX on mesoporous silica nanospheres was endothermic and spontaneous. The increase in solution temperature also aided in the removal of DOX. The kinetic study showed that the model suited the pseudo-second-order. The suggested adsorption method could recycle mesoporous silica nanospheres five times, with a modest reduction in its ability for adsorption. The most important feature of our adsorbent is that it can be recycled five times without losing its efficiency.

Synthesis of hybrid framework of tenorite and octahedrally coordinated aluminosilicate for the robust adsorption of cationic and anionic dyes

Adsorption is an important process for the industrial dye effluent treatment. Many adsorbents are employed such as activated carbon, metal oxide, molecular sieves etc. All those adsorbents are having their own setbacks like longer adsorption time and lower adsorption capacity. So development of fast adsorption and higher adsorption capacity is very much essential. In this view, we synthesized hybrid crystal system of tenorite and aluminosilicate framework (CuO@AS) for the faster adsorption. It is characterized by FT-IR, HRTEM and WAXRD. WAXRD proved the hybridization of two crystal systems viz tenorite & alumina in monoclinic phase and silica in trigonal phase. The crystal structure drawn based on the WAXRD data. It is observed that the tenorite and aluminosilicate framework are separate, but they are interlinked through Cu-O-Al and Cu-O-Si bond. This interconnection makes the aluminium in six coordination and Cu in four coordination. Aluminium and copper has 3 and 2 Brønsted acid sites respectively. Moreover, copper has three more OH group, so totally 5 H⁺ and 3 OH^- sites in copper and aluminium are responsible for the faster adsorption with high adsorption capacity compared to reported literature. To test the adsorption tendency, Victoria Blue (VB) and Metanil Yellow (MY) dyes are employed at room temperature. The rate constant of Pseudo-second order kinetics for the VB and MY are 0.002462 g mg^-1 min^-1 and 0.001619 g mg^-1 min^-1 which indicated faster adsorption of VB than MY. Moreover, total adsorption capacity for VB (636 mg/g) is higher than MY (52 mg/g). This is due to the hybridization of tenorite and aluminosilicate. Thermodynamic data such as ΔG°, ΔH° and ΔS° revealed that the adsorption is spontaneous, chemisorption and highly disordered in the adsorbent-adsorbate interface. This disorderness is due to the disordered pores present in the material.

Enhanced Adsorption and Evaluation of Tetracycline Removal in an Aquatic System by Modified Silica Nanotubes

In the present study, a nanocomposite adsorbent based on mesoporous silica nanotubes (MSNTs) loaded with 3-aminopropyltriethoxysilane (3-APTES@MSNTs) was synthesized. The nanocomposite was employed as an effective adsorbent for the adsorption of tetracycline (TC) antibiotics from aqueous media. It has an 848.80 mg/g maximal TC adsorption capability. The structure and properties of 3-APTES@MSNT nanoadsorbent were detected by TEM, XRD, SEM, FTIR, and N₂ adsorption-desorption isotherms. The later analysis suggested that the 3-APTES@MSNT nanoadsorbent has abundant surface functional groups, effective pore size distribution, a larger pore volume, and a relatively higher surface area. Furthermore, the influence of key adsorption parameters, including ambient temperature, ionic strength, initial TC concentration, contact time, initial pH, coexisting ions, and adsorbent dosage, had also been investigated. The 3-APTES@MSNT nanoadsorbent's ability to adsorb the TC molecules was found to be more compatible with Langmuir isothermal and pseudo-second-order kinetic models. Moreover, research on temperature profiles pointed to the process' endothermic character. In combination with the characterization findings, it was logically concluded that the 3-APTES@MSNT nanoadsorbent's primary adsorption processes involved interaction, electrostatic interaction, hydrogen bonding interaction, and the pore-fling effect. The synthesized 3-APTES@MSNT nanoadsorbent has an interestingly high recyclability of >84.6 percent up to the fifth cycle. The 3-APTES@MSNT nanoadsorbent, therefore, showed promise for TC removal and environmental cleanup.

Insights into the decolorization of mono and diazo dyes in single and binary dyes containing wastewater and electricity generation in up-flow constructed wetland coupled microbial fuel cell

The treatment of single and binary azo dyes, as well as the effect of the circuit connection, aeration, and plant on the performance of UFCW-MFC, were explored in this study. The decolorization efficiency of Remazol Yellow FG (RY) (single dye: 98.2 %; binary dye: 92.3 %) was higher than Reactive Black 5 (RB5) (single: 92.3 %; binary: 86.7 %), which could be due to monoazo dye (RY) requiring fewer electrons to break the azo bond compared to the diazo dye (RB5). In contrast, the higher decolorization rate of RB5 in binary dye indicated the removal rate was affected by the electron-withdrawing groups in the dye structure. The closed circuit enhanced about 2% of color and 4% of COD removal. Aeration improved the COD removal by 6%, which could be contributed by the mineralization of intermediates. The toxicity of azo dyes was reduced by 11-26% and the degradation pathways were proposed. The dye removal by the plants was increased with a higher contact time. RB5 was more favorable to be uptook by the plant as RB5 holds a higher partial positive charge. 127.39 (RY), 125.82 (RB5), and 58.66 mW/m³ (binary) of maximum power density were generated. The lower power production in treating the binary dye could be due to more electrons being utilized for the degradation of higher dye concentration. Overall, the UFCW-MFC operated in a closed circuit, aerated, and planted conditions achieved the optimum performance in treating binary azo dyes containing wastewater (dye: 87-92%; COD: 91%) compared to the other conditions (dye: 83-92%; COD: 78-87%).

Quantum-dot sensitized hierarchical NiO p–n heterojunction for effective photocatalytic performance

A facile and low-cost pseudo successive ionic layer adsorption and reaction technique was used to deposit cadmium sulfide quantum dots (CdS QDs) on hierarchical nanoflower NiO to form effective and intimate NiO/CdS, p–n heterojunctions.

Functionalized layered double hydroxides composite bio-adsorbent for efficient copper(II) ion encapsulation from wastewater

In this study, naturally abundant and inexpensive bamboo was used to make cheaper activated charcoal for efficient encapsulation of toxic copper (Cu(II)) ion from wastewater. The functionalized bamboo charcoal-Layered double hydroxides (BC-LDHs) composite bio-adsorbent was prepared using co-precipitation method. The composite bio-adsorbent was exploited to eliminate Cu(II) ion with high sensitivity and selectivity from contaminated water. The adsorption parameters including the effect of pH, contact time, adsorbent dose, and effect of initial concentration were optimized in systematic way and the adsorption kinetics and isotherms were investigated for potential use in real sample treatment. The physicochemical properties and morphological structure of the adsorbent were examined using X-ray Diffraction, Scanning Electronic Microscopy, Fourier Transform Infrared Spectroscopy and Thermogravimetric Analysis to understand the Cu(II) ion adsorption mechanism. The adsorption results revealed that the BC-LDH could remove almost 100% of Cu(II) ion from aqueous solution at pH range between 3.0 and 6.0 within 30 min. The maximum monolayer adsorption capacity was determined to be 85.47 mg/g based on the Langmuir isotherm. The adsorption equilibrium data were well-fitted by the Langmuir isotherm model (R² = 0.998) and the experimental kinetic data were supported by the pseudo-second order model (R² = 0.999). The BC-LDH could be reused without losing its adsorption performance in several cycles after successful regeneration with 0.10 M HCl. The Cu(II) ion removal mechanism was postulated with intercalated ion exchange, surface precipitation and interaction between BC-LDH and surface functionalities. Therefore, the highly functional BC-LDH composite could be a promising adsorbent for efficient Cu(II) ion removal from wastewater.

Novel micro-structured carbon-based adsorbents for notorious arsenic removal from wastewater

The contamination of groundwater by arsenic (As) in Bangladesh is the biggest impairing of a population, with a large number of peoples affected. Specifically, groundwater of Gangetic Delta is alarmingly contaminated with arsenic. Similar, perilous circumstances exist in many other countries and consequently, there is a dire need to develop cost-effective decentralized filtration unit utilizing low-cost adsorbents for eliminating arsenic from water. Morphological synthesis of carbon with unique spherical, nanorod, and massive nanostructures were achieved by solvothermal method. Owing to their intrinsic adsorption properties and different nanostructures, these nanostructures were employed as adsorption of arsenic in aqueous solution, with the purpose to better understanding the morphological effect in adsorption. It clearly demonstrated that carbon with nanorods morphology exhibited an excellent adsorption activity of arsenite (about 82%) at pH 3, remarkably superior to the two with solid sphere and massive microstructures, because of its larger specific surface area, enhanced acid strength and improved adsorption capacity. Furthermore, we discovered that iron hydroxide radicals and energy-induced contact point formation in nanorods are the responsible for the high adsorption of As in aqueous solution. Thus, our work provides insides into the microstructure-dependent capability of different carbon for As adsorption applications.

Assessing of cesium removal from wastewater using functionalized wood cellulosic adsorbent

Sustainable materials are urgently desired for treatment of radioactive cesium (Cs) contaminated water to safe-guard the public health. Apart from the synthetic ligand-based materials, the Mangrove charcoal modified adsorbent was fabricated for assessing of Cs removal from waste sample. The raw charcoal was oxidized using nitrification approach and diverse oxygen containing carboxyl, carbonyl and hydroxyl functional groups were introduced. After modification, the adsorbent characteristics were drastically changed as compared to the charcoal during the measurement of FTIR, N₂ adsorption-desorption isotherms and SEM micrographs. The data clarified that charcoal modified adsorbent was exhibited high Cs transport through the inner surface of the adsorbent based on bonding ability. The adsorbent was shown comparatively slow kinetics to Cs ion; however, the adsorption capacity was high as 133.54 mg/g, which was higher than the crown ether based conjugate materials. The adsorption data were followed to the Langmuir adsorption isotherms and the monolayer coverage was possible due to the data presentation. The presence of high amount of Na and K were slightly interfered to the Cs adsorption by the charcoal modified adsorbent, however; the Na and K concentration was 350-600 folds higher than the Cs concentration. Then the proposed adsorbent was selective to Cs for the potential real radioactive Cs contaminated water. The volume reduction was established rather than desorption and reuses advantages. More than 99% volume reduction was measured by burning of Cs adsorbed adsorbent at 500 °C for ensuring the safe storage and disposal of used adsorbent. Therefore, the charcoal modified adsorbent may open the new door to treat the Cs containing wastewater.

Silica Monolith for the Removal of Pollutants from Gas and Aqueous Phases

This study focused on the application of mesoporous silica monoliths for the removal of organic pollutants. The physico-chemical textural and surface properties of the monoliths were investigated. The homogeneity of the textural properties along the entire length of the monoliths was assessed, as well as the reproducibility of the synthesis method. The adsorption properties of the monoliths for gaseous toluene, as a model of Volatile Organic Compounds (VOCs), were evaluated and compared to those of a reference meso-structured silica powder (MCM-41) of commercial origin. Silica monoliths adsorbed comparable amounts of toluene with respect to MCM-41, with better performances at low pressure. Finally, considering their potential application in water phase, the adsorption properties of monoliths toward Rhodamine B, selected as a model molecule of water soluble pollutants, were studied together with their stability in water. After 24 h of contact, the silica monoliths were able to adsorb up to the 70% of 1.5 × 10⁻² mM Rhodamine B in water solution.

Efficient cesium encapsulation from contaminated water by cellulosic biomass based activated wood charcoal

In this study, cost-effective cellulosic biomass based activated wood charcoal was developed from Japanese Sugi tree (Cryptomeria japonica) by concentrated nitric acid modification for adsorption of Cs from contaminated water. The physicochemical properties of specimens were investigated using N₂ adsorption-desorption isotherms (BET method), FESEM, FTIR, and XPS spectra analysis. The experimental results revealed that the surface area of the raw wood charcoal was significantly decreased after boiling nitric acid modification. However, several oxygen-containing acidic function groups (-COOH, -CO) were introduced on the surface. The adsorption study confirmed that the equilibrium contact time was 1 h, the optimum adsorption pH was neutral to alkaline and the suitable adsorbent dose was 1:100 (solid: liquid). The maximum Cs was removed when the concentration of Na and K were lower (5.0 mM) with Cs in solution. The Cs adsorption processes well approved by the Langmuir isotherm and pseudo-second-order kinetic models and the maximum adsorption capacity was 35.46 mgg^-1. The Cs adsorption mechanism was clearly described and it was assumed that the adsorption was strongly followed by chemisorptions mechanism based on the adsorbent surface properties, kinetic model and Langmuir isotherm model. Most importantly, about 98% of volume reduction was obtained by burning (500 °C) the Cs adsorbed charcoal, which ensured safe storage and disposal of radioactive waste. Therefore, this study can offer a guideline to produce a functional adsorbent for effective Cs removal and safe radioactive waste disposal.

Highly efficient and fast removal of colored pollutants from single and binary systems, using magnetic mesoporous silica

Magnetic mesoporous silica material was tested as adsorbent for removal of two usual colored compounds present in industrial wastewater. The magnetic mesoporous silica was synthesized by modified sol-gel method and characterized from the morpho-textural, structural and magnetic point of view. The specific surface area and the total pore volume indicate a good adsorption capacity of the material, and the obtained saturation magnetization strength value denotes a good magnetic separation from solution. The adsorption capacity of magnetic mesoporous silica increases with the increase of the initial dye concentration, and the removal efficiency of the dyes was dependent on the pH of the solution and decreased with increasing temperature. The pseudo-second-order kinetic model described best the adsorption mechanism, and the maximum adsorption capacities were determined from the Sips isotherm model, being 88.29 mg/g for Congo Red and 208.31 mg/g for Methylene Blue. A complete thermodynamic evaluation was performed, by determining the free energy, enthalpy and entropy, and the result showed a spontaneous and exothermic adsorption process. The recovery and reutilization of the adsorbent were estimated in five cycles of adsorption-desorption, and the results indicated a good stability and reusability of magnetic mesoporous silica. The new magnetic mesoporous silica can be easily separated from solution, via an external magnetic field, and may be effectively applied as adsorbent for elimination of dyes from colored polluted waters.

Recent advances in the application of silica nanostructures for highly improved water treatment: a review

The demand for high-quality safe and clean water supply has revolutionized water treatment technologies and become a most focused subject of environmental science. Water contamination generally marks the presence of numerous toxic and harmful substances. These contaminants such as heavy metals, organic and inorganic pollutants, oil wastes, and chemical dyes are discharged from various industrial effluents and domestic wastes. Among several water treatment technologies, the utilization of silica nanostructures has received considerable attention due to their stability, sustainability, and cost-effective properties. As such, this review outlines the latest innovative approaches for synthesis and application of silica nanostructures in water treatment, apart from exploring the gaps that limit their large-scale industrial application. In addition, future challenges for improved water remediation and water quality technologies are keenly discussed.

Novel conjugated hybrid material for efficient lead(II) capturing from contaminated wastewater

An efficient material is always welcoming for the water treatment due to the need of clean water to safe the human health. The conjugate adsorbent (CJA) was fabricated by functional ligand embedded onto the highly porous silica material for selective lead (Pb(II)) ion monitoring and removal from wastewater. The study was achieved not only investigating the beginning material but also the performing extrusion as novel conjugate material, this defining the material novelty of this study considers to the modern state-of-art. The fabricated material was characterized in all aspects and then the experimental works for Pb(II) ion assessing were carried in batch mode. The CJA was exposed the color and signal intensity upon addition of Pb(II) ion from low to high concentrations. The optimum pH was considered at 5.50 based on the sensitivity, the color formation ability and high adsorption of Pb(II) ion. The determined limit of low detection was 0.18 μg/L, which was the extraordinary performance for the Pb(II) ion monitoring ability by the CJA. The adsorption efficiency, specific attention was remunerated to the influence of solution pH, reaction time, foreign ion, initial Pb(II) amounts and regeneration. The CJA was exhibited high kinetic performances and showed high adsorption Pb(II) ion compared with the different forms of material. The adsorption was completely fitted with the Langmuir adsorption as defining the monolayer coverage as expected of the homogeneous porosity of the CJA. The maximum adsorption was determined as high as 175.16 mg/g. In addition, the foreign ions were not affected in the Pb(II) adsorption by the CJA, and the adsorbent was regenerated using 0.20 M HCl for several cycles used without significant loss of the initial performance. Considering these advantages, the CJA demonstrated the potential low-cost material for competitive use in wastewater remediation, especially in the developing countries.

Composite nanofibers membranes of poly(vinyl alcohol)/chitosan for selective lead(II) and cadmium(II) ions removal from wastewater

The nanofibers membranes were fabricated by poly(vinyl alcohol)/chitosan (PVA/Chi) using an electro-spun technique for selective and high adsorption of lead (Pb(II)) and cadmium (Cd(II)) ions based on the solution acidity. The PVA/Chi NFs membranes were characterized systematically using several instrumentations. In addition, several experimental parameters such as initial metal ions concentration, interaction time, adsorbent dosage, solution pH and the effects of competing ions on Pb(II) and Cd(II) adsorption were evaluated. The adsorption data were also clarified that the PVA/Chi NFs membranes were exhibited high kinetic performances towards the both toxic ions at the optimum conditions. The adsorption data were manipulated using different kinetics models, and it was confirmed that only pseudo-second-order model obeyed the adsorption kinetics for Pb(II) and Cd(II) ions. Similarly, the equilibrium data were well fitted with the Langmuir adsorption isotherms model, and the maximum adsorption capacity was 266.12 and 148.79 mg/g for Pb(II) and Cd(II) ions, respectively. The Pb(II) and Cd(II) ions adsorptions were also measured to know the selectivity with simulated environmental solution, and the data were confirmed the high selectivity to Pb(II) and Cd(II) ions at the optimum condition and the nanofibers membrane shown the potentiality for possible use in efficient removal of the selected toxic ions from waste samples. Thus, the PVA/Chi NFs are considered to be effective and promising materials for Pb(II) and Cd(II) ions from wastewaters with high efficiency.

A ligand-anchored optical composite material for efficient vanadium(ii) adsorption and detection in wastewater

A ligand-anchored composite material was prepared for vanadium (V(ii)) ion capturing. The pH was found to be a key factor in both detection and removal operations. The composite material exhibited the high adsorption capacity of 492.61 mg g⁻¹.