Rapid and efficient removal of fluoride ions from aqueous solution using a polypyrrole coated hydrous tin oxide nanocomposite

Novel development of zinc oxide-coated carbon nanoparticles from pineapple leaves using sol gel method for optimal adsorption of Cu2+ and reuse in latent fingerprint application

This study underlines a latest approach of preparing nitrogen carbon nanoparticles fused on zinc oxide nanoparticle nanocomposite (N-CNPs/ZnONP nanocomposite) for the uptake of copper ions (Cu2+) from wastewater using a sol gel method. The metal loaded adsorbent was then applied in the latent fingerprint application. N-CNPs/ZnONP nanocomposite proved to be a good sorbent for the optimal adsorption of Cu2+ at pH 8 and 1.0 g/L dosage. Langmuir isotherm best fitted the process with the maximum adsorption capacity of 285.71 mg/g that was superior to most values reported in other studies for the removal of Cu2+. At 25 °C, the adsorption was spontaneous and endothermic. Furthermore, Cu2+-N-CNPs/ZnONP nanocomposite revealed to be sensitive and selective for latent fingerprint (LFP) identification on a variety of porous surfaces. As a result, it is an excellent identifying chemical for latent fingerprint recognition in forensic science.

Unraveling the Synergistic Mechanism of Boosted Photocatalytic H2O2 Production over Cyano-g-C3N4/In2S3/Ppy Heterostructure and Enhanced Photocatalysis-Self-Fenton Degradation Performance

In this work, cyano contained g-C3N4 comodified by In2S3 and polypyrrole (C≡N─CN/IS/Ppy) materials are synthesized for the photocatalytic production of H2O2 and photocatalysis-self-Fenton reaction for highly efficient degradation of metronidazole. The results from UV-vis spectrophotometry, surface photovoltage, and Kelvin probe measurements reveal the promoted transport and separation efficiency of photoinduced charges after the introduction of In2S3 and Ppy in the heterojunction. The existence of a built-in electric field accelerates the photoinduced charge separation and preserves the stronger oxidation ability of holes at the valence band of C≡N─CN. Linear sweep voltammetry measurements, zeta potential analyzations, nitroblue tetrazolium determination, and other measurements show that Ppy improves the conversion ratio of •O2 - to H2O2 and the utilization ratio of •O2 -, as well as suppresses decomposition of H2O2. Accordingly, the H2O2 evolution rate produced via a two-step single-electron reduction reaction reaches almost 895 µmol L-1 h-1, a value 80% and 7.2-fold higher than those obtained with C≡N─CN/IS and C≡N─CN, respectively. The metronidazole removal rate obtained via photocatalysis-self-Fenton reaction attains 83.7% within 120 minutes, a value much higher than that recorded by the traditional Fenton method. Overall, the proposed synthesis materials and route look promising for the H2O2 production and organic pollutants degradation.

Fluoride Adsorption from Aqueous Solution by Modified Zeolite-Kinetic and Isotherm Studies

Fluorine is a very common element in the Earth's crust and is present in the air, food, and in natural waters. It never meets in the free state in nature due to its high reactivity, and it comes in the form of fluorides. Depending on the concentration of fluorine absorbed, it may be beneficial or harmful to human health. Similar to any trace element, fluoride ion is beneficial for the human body at low levels, but as soon as its concentration becomes too high, it is toxic, inducing dental and bone fluorosis. The lowering of fluoride concentrations that exceed the recommended standards in drinking water is practiced in various ways around the world. The adsorption process has been classified as one of the most efficient methods for the removal of fluoride from water as it is environmentally friendly, easy to operate, and cost-effective. The present study deals with fluoride ion adsorption on modified zeolite. There are several influential parameters, such as zeolite particle size, stirring rate, solution pH, initial concentration of fluoride, contact time, and solution temperature. The maximum removal efficiency of the modified zeolite adsorbent was 94% at 5 mg/L fluoride initial concentration, pH 6.3, and 0.5 g modified zeolite mass. The adsorption rate increases accordingly with increases in the stirring rate and pH value and decreases when the initial fluoride concentration is increased. The evaluation was enhanced by the study of adsorption isotherms using the Langmuir and Freundlich models. The Langmuir isotherm corresponds with the experimental results of the fluoride ions adsorption with a correlation value of 0.994. The kinetic analysis results of the fluoride ions adsorption on modified zeolite allowed us to demonstrate that the process primarily follows a pseudo-second-order and then, in the next step, follows a pseudo-first-order model. Thermodynamic parameters were calculated, and the ΔG° value is found to be in the range of -0.266 kJ/mol up to 1.613 kJ/mol amidst an increase in temperature from 298.2 to 331.7 K. The negative values of the free enthalpy ΔG° mean that the adsorption of fluoride ions on the modified zeolite is spontaneous, and the positive value of the enthalpy ∆H° shows that the adsorption process is endothermic. The ∆S° values of entropy indicate the fluoride adsorption randomness characteristics at the zeolite-solution interface.

Green Synthesis of Hydroxyapatite Nanoparticles Using Monoon longifolium Leaf Extract for Removal of Fluoride from Aqueous Solution

Hydroxyapatite (Ca10(PO4)6(OH)2) calcium phosphate is a robust and viable magnetic material for the treatment of polluted air, water, and soil. Because of its unique structure and appealing properties such as high adsorption capabilities, acid-base adaptability, ion-exchange capability, and thermal stability, hydroxyapatite (HAp) has a lot of potential in the field of environmental management. An aqueous extract of Monoon longifolium leaves was used for the preparation of hydroxyapatite nonparticles as the adsorbent for fluoride ion removal from aqueous solution in this work, resulting in bio-based hydroxyapatite nanoparticles. The prepared adsorbent was characterized by using instrumental techniques such as TGA/DTA, XRD, AAS, FT-IR, and UV-Vis spectroscopy as well as SEM. The batch adsorption approach was used to determine the optimum adsorption efficiency of HAp NPs under various experimental conditions. As a result, the best removal efficiency corresponds to 0.75 g HAp NPs, 15 mg/L, and pH 7 at 50 minutes (96%). The equilibrium adsorption data were better fitted into the Freundlich isotherms (R2 = 0.99), and the pseudo-second-order kinetic model was found to be suitable (R2 = 0.99) for the kinetic model. Fluoride ion adsorption on HAp NPs is spontaneous, endothermic, and possible at temperatures over 318 K, according to thermodynamic calculations. The results hint at a conclusion that the synthesized HAp NPs were an efficient adsorbent for the removal of fluoride ions and the overall process can be an economical choice for scaled-up water treatment processes.

Template-Free Synthesis of Magnetic La-Mn-Fe Tri-Metal Oxide Nanofibers for Efficient Fluoride Remediation: Kinetics, Isotherms, Thermodynamics and Reusability

The occurrence of fluoride contamination in drinking water has gained substantial concern owing to its serious threat to human health. Traditional adsorbents have shortcomings such as low adsorption capacity and poor selectivity, so it is urgent to develop new adsorbents with high adsorption capacity, renewable and no secondary pollution. In this work, magnetic electrospun La-Mn-Fe tri-metal oxide nanofibers (LMF NFs) for fluoride recovery were developed via electrospinning and heat treatment, and its defluoridation property was evaluated in batch trials. Modern analytical tools (SEM, BET, XRD, FTIR) were adopted to characterize the properties of the optimized adsorbent, i.e., LMF11 NFs with a La:Mn molar ratio of 1:1. The surface area calculated via BET method and pH_pzc assessed using pH drift method of LMF11 NFs were 55.81 m² g^-1 and 6.47, respectively. The results indicated that the adsorption amount was highly dependent on the pH of the solution, and reached the highest value at pH = 3. The kinetic behavior of defluoridation on LMF11 NFs was dominated by the PSO model with the highest fitted determination coefficients of 0.9999. Compared with the other three isotherm models, the Langmuir model described defluoridation characteristics well with larger correlation coefficients of 0.9997, 0.9990, 0.9987 and 0.9976 at 15 °C, 25 °C, 35 °C and 45 °C, respectively. The optimized LMF11 NFs exhibited superior monolayer defluoridation capacities for 173.30-199.60 mg F^-/g at pH 3 at 15-45 °C according to the Langmuir isotherm model. A thermodynamic study proved that the defluoridation by LMF11 NFs is a spontaneous, endothermic along with entropy increase process. In addition, the LMF11 NFs still showed high defluoridation performance after three reused cycles. These findings unveil that the synthesized LMF11 NFs adsorbent is a good adsorbent for fluoride remediation from wastewater owing to its low cost, high defluoridation performance and easy operation.

Enhanced sorption and reduction of Cr(VI) by the flowerlike nanocomposites combined with molybdenum disulphide and polypyrrole

Developing high-performance adsorbent for hexavalent chromium (Cr(VI)) elimination presents an enticing prospect in environmental remediation. Herein, three-dimensional flowerlike nanospheres composed of molybdenum disulphide and polypyrrole (MoS₂@PPy) were successfully prepared via a one-pot hydrothermal and subsequent carbothermal reduction process for the removal of Cr(VI). The effects of pH, adsorbent dosage, co-existing ions, initial Cr(VI) concentration and temperature were investigated systematically by batch experiments. Benefiting from the incorporation of MoS₂, the obtained MoS₂@PPy composites showed a dramatic increase of specific surface area (149.82 m²·g^-1) and adsorption capacity (230.97 mg·g^-1) when compared with the pure PPy nanoparticles. Based on the thermodynamics study and X-ray photoelectron spectroscopy analyses, the removal process of Cr(VI) was proved to be exothermic and spontaneous, and accessible under-coordinated Mo(IV) and pyrrolic N groups coupled with redox reactions were conducive to the efficient removal of Cr(VI). Attractively, the MoS₂@PPy acted as the electron donor could also activate peroxymonosulphate for the efficient degradation of organic contaminants. These results suggested that the MoS₂@PPy was promising in Cr(VI) elimination and other kinds of organic pollutants removal in wastewater.

Facile preparation of UiO-66@PPy nanostructures for rapid and efficient adsorption of fluoride: Adsorption characteristics and mechanisms

A nanocomposite of a zirconium-based metal-organic framework (UiO-66) @ polypyrrole (PPy) (UiO-66@PPy) was successfully synthesized to eliminate F^- from groundwater. The optimum initial pH and adsorbent dose for maximum uptake of F^- from aqueous solution were found to be 3.0 and 0.1 g/L, respectively. The fluoride removal performance of UiO-66 was greatly enhanced through the introduction of polypyrrole guests, and the maximum adsorption capacity of UiO-66@PPy, namely, 290.7 mg/g, was reached, which is far superior to those of other previously reported adsorbents. The fluoride adsorption by UiO-66@PPy agreed well with the pseudo-second-order equation model and Langmuir isotherm model. The coexisting PO₄^3- and CO₃^2- substantially influence fluoride removal. The synthesized UiO-66@PPy could be reused five times in adsorption-desorption cycles. The incorporation of conducting polymers opened additional paths for the development of adsorbent materials; thus, UiO-66@PPy could be a viable adsorbent material and contribute to fluoride removal from groundwater.

Application of polypyrrole-based adsorbents in the removal of fluoride: a review

When fluoride levels in water exceed permitted limits (>1.5 mg L−1), water pollution becomes a major concern to humans.

Insight into the ion exchange in the adsorptive removal of fluoride by doped polypyrrole from water

In this study, the polypyrrole (PPy) samples doped with Cl^- (PPy-Cl), SO₄^2- (PPy-SO4) and SO₄^2-+Cl^- (PPy-SO4+Cl) were synthesized by chemical polymerization for the adsorptive removal of fluoride ion from water. The structure and morphology of the as-prepared PPy samples were characterized by FT-IR, BET, SEM, XPS, and zeta potential. The adsorption experiments revealed that the PPy-Cl exhibited faster kinetics and higher adsorption capacity (13.98 mg/g), more than 4 times that of PPy-SO4 (3.08 mg/g) and PPy-SO4+Cl (3.17 mg/g). The kinetics of the adsorption followed the pseudo-second-order model and the adsorption isotherm data fitted well to the Langmuir model. FT-IR, EDX, and XPS tests for PPy samples before and after fluoride adsorption demonstrated that anion exchange between F^- and Cl^- or SO4^2- was the prior mechanism for fluoride ion removal from water. Cl^- was more favorable than SO₄^2- in the ion exchange with F^-. Meanwhile, the Cl^- or SO₄^2- exchanged with F^- was mainly bound to the active nitrogen that accounts for 6% of the total nitrogen in PPy molecular matrix. Further study of zeta potential and pH influence experiment demonstrated the electrostatic interaction is auxiliary interaction for the fluoride removal by doped PPy samples.

Investigation of kinetics and adsorption isotherm for fluoride removal from aqueous solutions using mesoporous cerium-aluminum binary oxide nanomaterials

Herein, we report the synthesis of Ce–Al (1 : 1, 1 : 3, 1 : 6, and 1 : 9) binary oxide nanoparticles by a simple co-precipitation method at room temperature to be applied for defluoridation of an aqueous solution. The characterization of the synthesized nanomaterial was performed by XRD (X-ray diffraction), FTIR (Fourier transform infrared) spectroscopy, TGA/DTA (thermogravimetric analysis/differential thermal analysis), BET (Brunauer–Emmett–Teller) surface analysis, and SEM (scanning electron microscopy). Ce–Al binary oxides in 1 : 6 molar concentration were found to have the highest surface area of 110.32 m² g⁻¹ with an average crystallite size of 4.7 nm, which showed excellent defluoridation capacity. The adsorptive capacity of the prepared material towards fluoride removal was investigated under a range of experimental conditions such as dosage of adsorbents, pH, and initial fluoride concentration along with adsorption isotherms and adsorption kinetics. The results indicated that fluoride adsorption on cerium–aluminum binary metal oxide nanoparticles occurred within one hour, with maximum adsorption occurring at pH 2.4. The experimental data obtained were studied using Langmuir, Freundlich, and Temkin adsorption isotherm models. The nanomaterial showed an exceptionally high adsorbent capacity of 384.6 mg g⁻¹. Time-dependent kinetic studies were carried out to establish the mechanism of the adsorption process by pseudo-first-order kinetics, pseudo-second-order kinetics, and Weber–Morris intraparticle diffusion kinetic models. The results indicated that adsorption processes followed pseudo-second-order kinetics. This study suggests that cerium–aluminum binary oxide nanoparticles have good potential for fluoride removal from highly contaminated aqueous solutions.

Mesoporous Ce–Al binary oxide nanomaterials prepared with a surface area of 110.32 m² g⁻¹ showed defluoridation capacity at pH 2.4, exhibited maximum adsorption capacity of 384.6 mg g⁻¹ and a removal efficiency of 91.5% at a small dose of nanoadsorbent.

Nanobiocomposite Polymer as a Filter Nanosponge for Wastewater Treatment

A multifunctional nanobiocomposite polymer was developed in this study through a cross-linking polymerization of cyclodextrin with phosphorylated multi-walled carbon nanotubes followed by sol-gel to incorporate TiO₂ and Ag nanoparticles. This work’s novelty was to prove that the developed nanobiocomposite polymer is a potential filter nanosponge capable of removing organic, inorganic, and microorganisms’ pollutants from wastewater samples. The synthesized multifunctional nanobiocomposite polymer was characterized using a range of spectroscopy and electron microscopy techniques. Fourier-transform infrared (FTIR) confirmed the presence of oxygen-containing groups on the developed nanobiocomposite polymer and carbamate linkage (NH(CO)) distinctive peak at around 1645 cm⁻¹, which is evidence that the polymerization reaction was successful. The scanning electron microscopy (SEM) image shows that the developed nanobiocomposite polymer has a rough surface. The Dubinin–Radushkevich and the pseudo-second-order kinetic models best described the adsorption mechanism of Co²⁺ and TCE’s onto pMWCNT/CD/TiO₂-Ag. The efficacy of the developed nanobiocomposite polymer to act as disinfectant material in an environmental media (e.g., sewage wastewater sample) compared to the enriched media (e.g., nutrient Muller Hinton broth) was investigated. From the results obtained, in an environmental media, pMWCNT/CD/TiO₂-Ag nanobiocomposite polymer can alter the bacteria’s metabolic process by inhibiting the growth and killing the bacteria, whereas, in enriched media, the bacteria’s growth was retarded.

Removal of fluoride from industrial wastewater by using different adsorbents: A review

Many industries such as iron and steel metallurgy, copper and zinc smelting, the battery industry, and cement manufacturing industries discharge high concentrations of fluoride-containing wastewater into the environment. Subsequently, the discharge of high fluoride effluent serves as a threat to human life as well as the ecological ability to sustain life. This article analyses the advantages and drawbacks of some fluoride remediation technologies such as precipitation and flocculation, membrane technology, ion exchange technology, and adsorption technology. Among them, adsorption technology is considered the obvious choice and the best applicable technology. As such, several adsorbents with high fluoride adsorption capacity such as modified alumina, metal oxides, biomass, carbon-based materials, metal-organic frameworks, and other adsorption materials including their characteristics have been comprehensively summarized. Additionally, different adsorption conditions of the various adsorbents, such as pH, temperature, initial fluoride concentration, and contact time have been discussed in detail. The study found out that the composite synergy between different materials, morphological and structural control, and the strengthening of their functional groups can effectively improve the ability of the adsorbents for removing fluoride. This study has prospected the direction of various adsorbents for removing fluoride in wastewater, which would serve as guiding significance for future research in the field.

Descriptive data on trichloroethylene and Congo red dye adsorption from wastewater using bio nanosponge phosphorylated-carbon nanotube/nanoparticles polyurethane composite

The availability and quality of water resources is currently the primary concern in Southern Africa. The challenge is to improve or develop water treatment materials or methods to solve this problem of potable water scarcity. Hence, this article presents the analyzed data, which are supplementary data information on the study of bio nanosponge phosphorylated-carbon nanotube/nanoparticles polyurethane composite (pMWCNT/β-CD/TiO2-Ag) as polymeric nanobiosorbent, for water treatment. The developed polymeric nanobiosorbent (pMWCNT/β-CD/TiO2-Ag) was synthesized using combined methods of amidation reaction, cross polymerization, and sol-gel process. The removal of water pollutants (trichloroethylene (TCE) and Congo red (CR) dye) was conducted by the batch adsorption method. The conditions used during the adsorption experiments and methods (applied to quantify the water samples after adsorption studies) are described. Additional data obtained on the effect of pH, isotherm, kinetic, and thermodynamic studies are also illustrated.

A review of bismuth-based sorptive materials for the removal of major contaminants from drinking water

In recent years, bismuth has gained attention of many researchers because of its sorptive properties. Sorptive properties of bismuth compounds are used for removal of ionic contaminants from aqueous solution. In this paper, an attempt is made to review the recent developments in the area of contaminant removal from aqueous solutions using bismuth-based media. List of various bismuth-based adsorbents are collected from published literature and their adsorption capacities are also compared. The methods of characterization of some of the synthesized bismuth-based materials have also been discussed. Hydrous bismuth oxides (HBOs) have sorptive potential for nitrate and fluoride removal from aqueous solution with maximum capacity of 0.508-0.512 mg/g and 0.60-1.93 mg/g respectively. Thus, it can be beneficially used for treatment of drinking water treatment, particularly in small scale household applications.

A simple chemical method for the synthesis of Cu2+ engrafted MgAl2O4 nanoparticles: Efficient fluoride adsorbents, photocatalyst and latent fingerprint detection

An adaptable, energy efficient chemical process is employed to synthesize Cu²⁺ engrafted MgAl₂O₄ nanoparticles (Mg_1-xCu_xAl₂O₄, x=0, 0.1, 0.3, 0.5 abbreviated as MCA0, MCA1, MCA3, and MCA5 respectively), using chelating ligand and the calcination temperature was determined by the thermogravimetric analysis of the precursor mass. They acted as good fluoride adsorbent in the presence of co-ions, different pH (2-11) via chemisorption revealed from Fourier-transform infrared spectroscopy (FTIR) and photodegraded Methylene Blue (MB). The satisfactory results were for MCA1 (specific surface area 25.05m²/g) with 97% fluoride removal at pH7.0 for the 10mg/L initial fluoride concentration for 1.5g/L adsorbent dose with 45min contact time obeying the Langmuir isotherm model with negative thermodynamic parameters and 4mmol of MCA3 with 98.51% photodegradation for 10^-5mol/LMB solution obeying pseudo-second-order and pseudo-first-order kinetics respectively. The proposed photodegradation mechanism of MB was established by the FTIR and high-performance liquid chromatography (HPLC) analysis. The nanoparticles are cubic, estimated through X-ray diffraction (XRD) and transmission electron microscopy (TEM) analysis. The band gap energies, grain size, and the effective working pH were estimated by diffuse reflectance spectra (DRS), scanning electron microscope (SEM), and zero-point potential analysis respectively. A soil candle with MCA1 also fabricated for the household purpose and tested with some fluorinated field samples. The MCA3 was able to enhance the latent fingerprint on smooth surfaces.

Synthesis of nano-scale zero-valent iron-reduced graphene oxide-silica nano-composites for the efficient removal of arsenic from aqueous solutions

Design and synthesis of arsenic adsorbents with high performance and excellent stability has been still a significant challenge. In this study, we anchored nano-zero-valent iron (NZVI) on the surface of graphene-silica composites (GS) with high specific surface area, forming the NZVI/GS nano-composite. The prepared nano-materials were used to remove As(III) and As(V) through adsorption from aqueous solutions. The results indicated that NZVI particles were dispersed well on the surface of GS, and the NZVI/GS showed great potential to remove As(III) and As(V). Adsorption performance of NZVI/GS for As(III) and As(V) highly depended on the pH of solutions. The experimental data fitted well with the pseudo-second-order kinetic model and the Langmuir isotherm model. The calculated maximum adsorption capacities of NZVI/GS for As(III) and As(V) were up to 45.57 mg/g and 45.12 mg/g at 298 K, respectively, and the adsorption equilibrium could be reached within 60 min. The residual concentrations of As(III) and As(V) after treatment with 0.4 g/L NZVI/GS can meet with the drinking water standard of WHO when the initial concentrations were below 4 mg/L and 3 mg/L, respectively. Moreover, the as-prepared NZVI/GS had excellent anti-interference ability during the process of As removal in the presence of foreign ions. During the As removal process, As(III) was oxidized to As(V), which could be removed through adsorption by electrostatic attraction and complexation. These results indicated that the as-synthesized NZVI/GS composite is a promising adsorbent for the removal of arsenic from aqueous solutions.

Carboxymethyl cellulose thiol-imprinted polymers: Synthesis, characterization and selective Hg(II) adsorption

Sulfur containing ion imprinted polymers (S-IIPs) were applied for the uptake of Hg(II) from aqueous solution. Cysteamine which was used as the ligand for Hg(II) complexation, was grafted along the epichlorohydrin crosslinked carboxylated carboxymethyl cellulose polymer chain through an amide reaction. The adsorption ability of S-IIPs towards Hg(II) was investigated by kinetic and isotherm models, which, corresponding, showed that the adsorption process followed a pseudo-second-order, fitted well with the Langmuir isotherm with a maximum adsorption capacity of 80 mg/g. Moreover, thermodynamic studies indicated an endothermic and spontaneous reaction with the tendency of an enhanced randomness at the surface of the S-IIPs with temperature increases. S-IIPs indicated a high degree of selectivity towards Hg(II) in the presence of Cu²⁺, Zn²⁺, Co²⁺, Pb²⁺ and Cd²⁺. Furthermore, the efficiency of S-IIPs was also evaluated against real samples showing 86.78%, 91.88%, and 99.10% recovery for Hg(II) wastewater, ground water and tap water, respectively. In this study, the adsorbent was successfully regenerated for five cycles, which allows for their reuse without significant loss of initial adsorption capability.

Removal of cobalt and lead ions from wastewater samples using an insoluble nanosponge biopolymer composite: adsorption isotherm, kinetic, thermodynamic, and regeneration studies

In this study, an insoluble nanosponge biopolymer composite was synthesized, using a combined process of amidation reaction, cross-linking polymerization, and sol-gel method to obtain a phosphorylated multiwalled carbon nanotube-cyclodextrin/silver-doped titania (pMWCNT-βCD/TiO₂-Ag). This work mainly emphasized on the removal of lead (Pb²⁺) and cobalt (Co²⁺) metal ions from synthetic and real wastewater samples using the synthesized pMWCNT-βCD/TiO₂-Ag as a biosorbent. The new material was characterized by Fourier transform infrared (FTIR) spectroscopy, zeta potential, Brunauer-Emmett-Teller (BET) method, and scanning electron microscopy (SEM). Adsorption studies for the model pollutants were performed in batch mode. The effect of the solution pH, adsorbent dosage and the presence of competiting ions were investigated. The isotherm, kinetic, thermodynamic, and regeneration studies were also undertaken. The ability of the new material to effectively remove Pb²⁺ and Co²⁺ from synthetic wastewater and mine effluent samples was tested. The maximum removal capacities achieved for the removal of Pb²⁺ and Co²⁺ from mine effluent sample were 35.86 and 7.812 mg/g, respectively.

Synthesis of graphene/SiO2@polypyrrole nanocomposites and their application for Cr(VI) removal in aqueous solution

A novel hybrid nanocomposite, polypyrrole nanoparticles (PPy) anchored on the graphene/silica nanosheets with the high specific surface area (polypyrrole-graphene/silica, GS-PPy), was synthesized by a facile in situ polymerization and shows great potential to remove hexavalent chromium [Cr(VI)] in aqueous solutions. Characterizations by XRD, TEM, SEM, BET, FT-IR and XPS, have confirmed that the PPy nanoparticles were well-distributed on the surface of GS nanosheets. The effects of pH, contact time, the concentration of Cr(VI), temperature, coexisting ions and the number of adsorption-desorption cycles were studied. The maximum adsorption capacity of the GS-PPy for Cr(VI) was 429.2 mg g^-1 at 298 K at pH 2, which was much higher than PPy nanoparticles and other related materials. The adsorption data fitted to the pseudo-second-order model and Langmuir isotherm model. The removal mechanism involved in electrostatic attraction, ion exchange and reduction process that partial adsorbed Cr(VI) was reduced to Cr(III). And Cr(III) was still retained on the surface of GS-PPy. The GS-PPy nanocomposite will be a potential candidate for the removal of Cr(VI) from the industrial waste water.

Hydrous TiO2@polypyrrole hybrid nanocomposite as an efficient selective scavenger for the defluoridation of drinking water

An adsorptive process for the defluoridation of drinking water was performed using a hybrid nanocomposite of hydrous titanium oxide@polypyrrole (HTiO₂@PPy), as a scavenger.

Preparation and characterization of a composite based on polyaniline, polypyrrole and cigarette filters: adsorption studies and kinetics of phenylbutazone in aqueous media

PAni–PPy–CFs composite was prepared by a static one-step triple-phase interfacial reaction, in which the PAni and PPy particles were formed and aggregated on CFs resulting in a composite with fibrous domains and good adsorption proprieties.