Catalytic decomposition of 2-chlorophenol using an ultrasonic-assisted Fe3O4–TiO2@MWCNT system: Influence factors, pathway and mechanism study

Aptamer-functionalized Fe3O4/MWCNTs@Mo-CDs nanozyme for rapid colorimetric detection toward Escherichia coli

The pathogenic bacteria induced foodborne disease has been detrimental to public health worldwide. Herein, the peroxidase (POD)-like Fe3O4/MWCNTs@Mo-CDs (FMMC) nanozyme was applied for the detection of Escherichia coli (E. coli). The E. coli aptamer was conjugated with the surface of the FMMC, which effectively enhanced the POD-like activity attributing to the higher affinity to the substrate, and then specific capture of E. coli in food matrices, leading to the reduction of POD-like activity. Therefore, a robust and facile colorimetric aptasensor was developed for detecting E. coli with a wide linear range of 101-106 CFU/mL, low LOQ of 101 CFU/mL and LOD of 0.978 CFU/mL. The aptasensor demonstrated the satisfied selectivity for E. coli compared to the other strains. This method possessed the potential application for fast in situ screening of foodborne pathogens in food products.

Photoluminescence and Photocatalytic Properties of MWNTs Decorated with Fe-Doped ZnO Nanoparticles

The present work reports the photoluminescence (PL) and photocatalytic properties of multi-walled carbon nanotubes (MWCNTs) decorated with Fe-doped ZnO nanoparticles. MWCNT:ZnO-Fe nanocomposite samples with weight ratios of 1:3, 1:5 and 1:10 were prepared using a facile synthesis method. The obtained crystalline phases were evidenced by X-ray diffraction (XRD). X-ray Photoelectron spectroscopy (XPS) revealed the presence of both 2+ and 3+ valence states of Fe ions in a ratio of approximately 0.5. The electron paramagnetic resonance EPR spectroscopy sustained the presence of Fe³⁺ ions in the ZnO lattice and evidenced oxygen vacancies. Transmission electron microscopy (TEM) images showed the attachment and distribution of Fe-doped ZnO nanoparticles along the nanotubes with a star-like shape. All of the samples exhibited absorption in the UV region, and the absorption edge was shifted toward a higher wavelength after the addition of MWCNT component. The photoluminescence emission spectra showed peaks in the UV and visible region. Visible emissions are a result of the presence of defects or impurity states in the material. All of the samples showed photocatalytic activity against the Rhodamine B (RhB) synthetic solution under UV irradiation. The best performance was obtained using the MWCNT:ZnO-Fe(1:5) nanocomposite samples, which exhibited a 96% degradation efficiency. The mechanism of photocatalytic activity was explained based on the reactive oxygen species generated by the nanocomposites under UV irradiation in correlation with the structural and optical information obtained in this study.

Synthesis, Structure, and Antimicrobial Performance of NixZn1−xFe2O4 (x = 0, 0.3, 0.7, 1.0) Magnetic Powders toward E. coli, B. cereus, S. citreus, and C. tropicalis

The active development of water purification functional materials based on multicomponent spinel ferrites makes it necessary to search for new efficient methods of obtaining initial nanostructured powders. In this study, a two-stage method for the synthesis of perspective pollutant absorption agents based on NixZn1−xFe2O4 (x = 0, 0.3, 0.7, 1.0) spinel ferrites are proposed and implemented. The approach is based on the synthesis of the initial powder using the solution combustion method and its subsequent thermal treatment in the air. It was found that synthesized samples are single-phase Ni-Zn ferrites with an average crystallite size of 41.4 to 35.7 nm and a degree of crystallinity of ~95–96%. The analysis of antimicrobial activity against four diverse test-cultures: Escherichia coli ATCC 11229 (non-spore-forming gram-negative), Bacillus cereus ATCC 10702 (spore-forming gram-positive), Staphylococcus citreus NCTC 9379 (non-spore-forming gram-positive), and Candida tropicalis ATCC 750 (yeast) showed that almost all of the synthesized powders exhibit an advanced ability to inhibit the growth of the microorganisms mentioned above. The compositions obtained can be a perspective basis for both natural and wastewater purificators with magnetic separation ability and can find biotechnological and biomedical applications as promising antimicrobial materials.

Step-scheme BiVO4/WO3 heterojunction photocatalyst under visible LED light irradiation removing 4-chlorophenol in aqueous solutions

In the present study, photodegradation of 4-chlorophenol (4-CP) using a step-scheme BiVO₄/WO₃ heterostructure under visible LED light irradiation (Vis LED) from aqueous solutions was investigated. The photocatalyst was synthesized through the hydrothermal process and characterized physically and chemically via X-ray diffraction (XRD), field emission scanning electron microscope (FE-SEM), energy-dispersive X-ray (EDX), and Brunnauer-Emmett-Teller (BET) techniques. The effects of the operational parameters i.e., solution pH, contact time, nanocomposite dosage, and initial 4-CP concentration were evaluated. Results indicated that BiVO₄/WO₃/Vis LED process has higher efficiency in 4-CP degradation than BiVO₄/Vis LED, WO₃/Vis LED, and BiVO₄/WO₃ systems. At BiVO₄/WO₃ concentration of 0.125 g/L, initial pH of 7, and initial 4-CP concentration of 25 mg/L, complete degradation of 4-CP (>97%) was achieved in reaction time of 60 min. The phenol, chlorobenzene, catechol, 4-chlorocatechol, 5-chloro-1,2,4-benzenetriol, hydroquinone, hydroxyhydroquinone, p-benzoquinone, o-benzoquinone, formic acid, acetic acid, and oxalic acid were identified as the major intermediates of 4-CP degradation. In optimal condition, 67.5% and 88.5% of TOC and COD removal rates were obtained in 120 min contact time, respectively. The degradation of 4-CP was pseudo-first-order kinetics. Through the use of tert-Butyl alcohol (TBA) and ethylenediamine tetraacetic acid (EDTA) as radical scavengers, hydroxyl radicals and holes were identified as the main active species in photocatalytic degradation. Also, a tentative pathway for 4-CP degradation using the Vis LED/BiVO₄/WO₃ process was proposed.

Green carbonaceous material‒fibrous silica-titania composite photocatalysts for enhanced degradation of toxic 2-chlorophenol

In this work, fibrous silica-titania (FST) was successfully prepared by the microemulsion method prior to the addition of three types of carbonaceous materials: graphitic-carbon nitride, g-C3N4 (CN), graphene nanoplatelets (GN), and multi-wall carbon nanotubes, MWCNT (CNT), via a solid-state microwave irradiation technique. The catalysts were characterized using XRD, FESEM, TEM, FTIR, UV-Vis DRS, N2 adsorption-desorption, XPS and ESR, while their photoactivity was examined on the degradation of toxic 2-chlorophenol (2-CP). The result demonstrated that the initial reaction rate was in the following order: CNFST (5.1 × 10^-3 mM min^-1) > GNFST (2.5 × 10^-3 mM min^-1) > CNTFST (2.3 × 10^-3 mM min^-1). The best performance was due to the polymeric structure of g-C3N4 with a good dispersion of C and N on the surface FST. This dispersion contributed towards an appropriate quantity of defect sites, as a consequence of the greater interaction between g-C3N4 and the FST support, that led to narrowed of band gap energy (2.98 eV to 2.10 eV). The effect of scavenger and ESR studies confirmed that the photodegradation over CNFST occurred via a Z-scheme mechanism. It is noteworthy that the addition of green carbonaceous materials on the FST markedly enhanced the photodegradation of toxic 2-CP.

Metagenomic analysis of microbial community and its role in bioelectrokinetic remediation of tannery contaminated soil

Tanneries create a serious threat to the environment by generating a significant amount of toxic metal-containing solid waste. This study deals with the application of bio-electrokinetic remediation (Bio-EK) of tannery effluent contaminated soil (TECS). Metagenomes representing the TECS sample were sequenced using the Illumina HiSeq platform. The bioreduction of hexavalent chromium Cr(VI)to trivalent chromium Cr (III) was achieved by BIO-EK techniques. NGS-data (Next Generation Sequencing) analysis was revealed that Proteobacteria, Firmicutes, Bacteroidetes, Actinobacteria, and Planctomycetes were identified in the bio-electrokinetic system. Proteobacteria are responsible for the bioreduction of chromium hexavalent by the formation of FeS particles. The bio-generated FeS particles can be reduced the toxic chromium (VI) to non-toxic chromium (III) in soil. Simultaneously total chromium and organic content were significantly removed in BIO-EK (40 and 290 mg kg^-1) when compared to control soil (182 and 240 mg kg^-1). The presence of pollutant degrading microbes such as Desulfovibrio, Pseudomonas, Bacillus, Clostridium, Halanaerobium enhanced the bioreduction of the chromium during the electrokinetic remediation. This study can be claimed that the microbial cultures assisted electrokinetic remediation of total chromium, organic and iron in the tannery effluent contaminated soil was one of the suitable efficient techniques. In addition, the viability of the new combination technology developed (Electrokinetic + Bio) to treat low-permeability polluted soils was demonstrated.

Magnetic Nanoparticle Composites: Synergistic Effects and Applications

Composite materials are made from two or more constituent materials with distinct physical or chemical properties that, when combined, produce a material with characteristics which are at least to some degree different from its individual components. Nanocomposite materials are composed of different materials of which at least one has nanoscale dimensions. Common types of nanocomposites consist of a combination of two different elements, with a nanoparticle that is linked to, or surrounded by, another organic or inorganic material, for example in a core-shell or heterostructure configuration. A general family of nanoparticle composites concerns the coating of a nanoscale material by a polymer, SiO2 or carbon. Other materials, such as graphene or graphene oxide (GO), are used as supports forming composites when nanoscale materials are deposited onto them. In this Review we focus on magnetic nanocomposites, describing their synthetic methods, physical properties and applications. Several types of nanocomposites are presented, according to their composition, morphology or surface functionalization. Their applications are largely due to the synergistic effects that appear thanks to the co-existence of two different materials and to their interface, resulting in properties often better than those of their single-phase components. Applications discussed concern magnetically separable catalysts, water treatment, diagnostics-sensing and biomedicine.

Insights into the novel application of Fe-MOFs in ultrasound-assisted heterogeneous Fenton system: Efficiency, kinetics and mechanism

In this work, as a new strategy, ultrasound/H₂O₂/MOF system was firstly applied by environmental-benign Fe-MOFs (MIL-53, MIL-88B and MIL-101) for tetracycline hydrochloride removal. The syntheticFe-MOFs were characterized by XRD, FTIR, SEM, XPS, N₂ sorption-desorption isotherms and CO-FTIR. MIL-88B demonstrated the best catalytic performance because of its highest amount of Lewis acid sites. Influencing factors, contrast experiment, and corresponding dynamics were carried out to obtain the best experimental conditions and reaction system. Under optimal conditions ([Tetracyclinehydrochloride] = 10 mg/L, [MIL-88B] = 0.3 g/L, [H₂O₂] = 44 mM, [ultrasound power] = 60 W, and pH = 5.0), the-first-order kinetic rate constant k was calculated to be 0.226 min^-1, higher than the simple combination of the ultrasound system (0.004) and MIL-88B/H₂O₂ system (0.163), indicating the importance of synergistic effect between ultrasound and Fenton reaction. EPR test and quenching experiment proved that ·OH is mainly responsible for tetracycline hydrochloride removal. The major reaction path is the adsorption and decomposition of H₂O₂ by coordinative unsaturated iron sites on Fe-MOF, but it is not the only path. The direct decomposition of H₂O₂ and the cavitation effect caused by ultrasound also contribute to the generation of OH.

Magnetic carnosine-based metal-organic framework nanoparticles: fabrication, characterization and application as arsenic adsorbent

This study centers on the controllable synthesis, characterization, and application of a novel magnetic bio-metal-organic framework (Bio-MOF) for the adsorption and subsequent removal of arsenic from aqueous solutions. Zinc ions and carnosine (Car) were exploited to construct the Car-based MOF on the surface of magnetite (Fe₃O₄ NPs). The Magnetite precoating with Car led to an increase in the yield and the uniform formation of the magnetic MOF. The prepared magnetic Bio-MOF nanoparticles (Fe₃O₄-Car-MOF NPs) had semi-spherical shape with the size in the range of 35-77 nm, and the crystalline pattern of both magnetite and Car-based MOF. The NPs were employed as an adsorbent for arsenic (As) removal. The adsorption analyses revealed that all studied independent variables including pH, adsorbent dose, and initial arsenic concentration had a significant effect on the arsenic adsorption, and the adsorption data were well matched to the quadratic model. The predicted adsorption values were close to the experimental values confirming the validity of the suggested model. Furthermore, adsorbent dose and pH had a positive effect on arsenic removal, whereas arsenic concentration had a negative effect. The adsorption isotherm and kinetic studies both revealed that As adsorption fitted best to the Freundlich isotherm model. The maximum monolayer adsorption capacity (94.33 mg/g) was achieved at room temperature, pH of 8.5 and adsorbent dose of 0.4 g/L. Finally, the results demonstrated that the adsorbent could be efficiently applied for arsenic removal from aqueous environment.

Rapid Sonochemically-Assisted Synthesis of Highly Stable Gold Nanoparticles as Computed Tomography Contrast Agents

One of the most widely used modalities of clinical imaging is computed tomography (CT). Recent reports of new contrast agents toward CT imaging have been numerous. The production of gold nanoparticles (AuNPs) as contrast agents for CT is primarily a topic of intense interest. AuNPs have beneficial features for this application, including excellent X-ray attenuation, flexible sizes and shapes, tailorable surface chemistry, excellent biocompatibility and high levels of contrast generating matter. AuNPs with a size of about 18.5 nm and semi-spherical shape were synthesized using a sonochemical method. The attenuation rate of X-rays as measured in Hounsfield units per unit concentration (HU/mg) was measured. Ultrasound treatment for a duration of five min has been shown to produce highly stable AuNPs in different media (AuNPs in water and phosphate-buffered saline (PBS) was −42.1 mV and −39.5 mV, respectively). The CT value (HU = 395) of the AuNPs increased linearly with an increase in the AuNP dosage. The results confirm the use of ultrasonic treatment for the production of metal nanostructures, particularly highly stable non-toxic AuNPs, with good morphology and high-quality crystal structure using an easy and fast method. Synthesized AuNPs have the potential to be used as a CT contrast agent in medical imaging applications.

Green preparation of activated carbon from pomegranate peel coated with zero-valent iron nanoparticles (nZVI) and isotherm and kinetic studies of amoxicillin removal in water

In present research, the activated carbon was prepared by a green approach from pomegranate peel coated with zero-valent iron nanoparticles (AC-nZVI) and developed as adsorbent for the removal of amoxicillin from aqueous solution. The physicochemical properties of the AC-nZVI were investigated using XRD, FTIR, and FESEM techniques. The optimal values of the parameters for the best efficiency (97.9%) were amoxicillin concentration of 10 mg/L, adsorbent dose of 1.5 g/L, time of 30 min, and pH of 5, respectively. The adsorption equilibrium and kinetic data were fitted with the Langmuir monolayer isotherm model (qmax 40.282 mg/g, R² 0. 0.999) and pseudo-first order kinetics (R² 0.961). The reusability of the adsorbent also revealed that the adsorption efficiency decreased from 83.54 to 50.79% after five consecutive repetitions. Overall, taking into account the excellent efficiency, availability, environmental friendliness, and good regeneration, AC-nZVI can be introduced as a promising absorbent for amoxicillin from aquatic environments.

Adsorption, degradation, and mineralization of emerging pollutants (pharmaceuticals and agrochemicals) by nanostructures: a comprehensive review

This review discusses a fresh pool of research findings reported on the multiple roles played by metal-based, magnetic, graphene-type, chitosan-derived, and sonicated nanoparticles in the treatment of pharmaceutical- and agrochemical-contaminated waters. Some main points from this review are as follows: (i) there is an extensive number of nanoparticles with diverse physicochemical and morphological properties which have been synthesized and then assessed in their respective roles in the degradation and mineralization of many pharmaceuticals and agrochemicals, (ii) the exceptional removal efficiencies of graphene-based nanomaterials for different pharmaceuticals and agrochemicals molecules support arguably well a high potential of these nanomaterials for futuristic applications in remediating water pollution issues, (iii) the need for specific surface modifications and functionalization of parent nanostructures and the design of economically feasible production methods of such tunable nanomaterials tend to hinder their widespread applicability at this stage, (iv) supplementary research is also required to comprehensively elucidate the life cycle ecotoxicity characteristics and behaviors of each type of engineered nanostructures seeded for remediation of pharmaceuticals and agrochemicals in real contaminated media, and last but not the least, (v) real wastewaters are extremely complex in composition due to the mix of inorganic and organic species in different concentrations, and the presence of such mixed species have different radical scavenging effects on the sonocatalytic degradation and mineralization of pharmaceuticals and agrochemicals. Moreover, the formulation of viable full-scale implementation strategies and reactor configurations which can use multifunctional nanostructures for the effective remediation of pharmaceuticals and agrochemicals remains a major area of further research.

Biochar derived from red algae for efficient remediation of 4-nonylphenol from marine sediments

4-Nonylphenol (4-NP), a phenolic endocrine disruptor chemical (EDC), is known to have high toxicity to aquatic organisms and humans. The remediation of 4-NP-contaminated marine sediments was studied using red algae-based biochar (RAB) thermochemically synthesized from Agardhiella subulata with simple pyrolysis process under different temperatures of 300-900 °C in CO₂ atmosphere. The RAB was characterized by XRD, Raman, FTIR spectroscopy, and zeta potential measurements. The calcium in RAB efficiently activated sodium percarbonate (SPC) to generate reactive radicals for the catalytic degradation of 4-NP at pH 9.0. The oxygen-containing functional groups reacted with H₂O₂, which increased the generation of reactive radicals under alkaline pH condition. Ca²⁺ ion was the active species responsible for 4-NP degradation. CaO/CaCO₃ on RAB surface enhanced direct electron transfer, increased HO production, and 4-NP degradation in marine sediments. Langmuir‒Hinshelwood type kinetics well described the 4-NP degradation process. Remediation of contaminated sediments using RAB could be a sustainable approach toward closed-loop biomass cycling in the degradation of 4-NP contaminants.

Ultrasonic degradation of nitrosodipropylamine (NDPA) and nitrosodibutylamine (NDBA) in water

Nitrosodipropylamine (NDPA) and nitrosodibutylamine (NDBA), two highly toxics and carcinogenic disinfection by-products, cannot be efficiently removed by conventional water treatment processes, while the ultrasound treatment was developed as a promising alternative. In this work, nitrosodipropylamine (NDPA) and nitrosodibutylamine (NDBA) are degraded by ultrasound treatment. Greater than 99% of NDPA and NDBA mixing solution could be decomposed within 60 min at neutral pH under optimal ultrasound power and frequency settings of 100 W and 600 kHz, respectively. Free radical reactions (OH•) played a significant role and the reaction sites were predominately at the bubble interface. The degradation of both NDPA and NDBA exhibited pseudo-first-order degradation kinetics, and the rate constant k_app was influenced by a number of factors including ultrasonic frequency, power, initial concentration, initial pH, various anions and cations frequently present in drinking water, hydroxyl radical scavengers, and water matrices, especially the promoting effect of various anions and cations and water matrices. The results of this study suggest the potential for ultrasound treatment as a method for removing NAms from water.

Facile and efficient 3-chlorophenol sensor development based on photolumenescent core-shell CdSe/ZnS quantum dots

Quantum dots (QDs) are semiconducting inorganic nanoparticles, tiny molecules of 2-10 nm sizes to strength the quantum confinements of electrons. The QDs are good enough to emit light onto electrons for exciting and returning to the ground state. Here, CdSe/ZnS core/shell QDs have been prepared and applied for electrochemical sensor development in this approach. Flat glassy carbon electrode (GCE) was coated with CdSe/ZnS QDs as very thin uniform layer to result of the selective and efficient sensor of 3-CP (3-chlorophenol). The significant analytical parameters were calculated from the calibration plot such as sensitivity (3.6392 µA µM-1 cm-2) and detection limit (26.09 ± 1.30 pM) with CdSe/ZnS/GCE sensor probe by electrochemical approach. The calibration curve was fitted with the regression co-efficient r2 = 0.9906 in the range of 0.1 nM ∼ 0.1 mM concentration, which denoted as linear dynamic range (LDR). Besides these, it was performed the reproducibility in short response time and successfully validated the fabricated sensor for 3-CP in the real environmental and extracted samples. It is introduced as a noble route to detect the environmental phenolic contaminants using CdSe/ZnS QDs modified sensor by electrochemical method for the safety of healthcare and environmental fields at broad scales.

ZnO–TiO2: Synthesis, Characterization and Evaluation of Photo Catalytic Activity towards Degradation of Methyl Orange

Here in, we report the synthesis and characterization of ZnO–TiO2 composite as a potential photo catalyst for photo degradation of methyl orange under UV irradiation. ZnO–TiO2 with 1:1 ratio was synthesized via wet incipient impregnation method using TiO2 and Zn(NO3)2 ⋅ 6H2O as precursor material and the prepared composite was characterized by XRD, EDX and SEM. The synthesized composite was employed as photo catalyst for photo degradation of methyl orange. The photo degradation results showed that ZnO–TiO2 exhibited better catalytic performance than ZnO and TiO2 alone. The methyl orange photo degradation efficiency was determined to be 98, 75 and 60% over ZnO–TiO2, ZnO and TiO2 respectively using 50 mL solution of 100 mg/L at 40 °C for 120 min. The ZnO–TiO2 catalyzed photo degradation of methyl orange followed pseudo-first-order kinetic in terms of Langmuir–Hinshelwood mechanism.

Flexible and porous TiO2/SiO2/carbon composite electrospun nanofiber mat with enhanced interfacial charge separation for photocatalytic degradation of organic pollutants in water

Semiconductor photocatalysis has long been considered as a promising approach for remediation of polluted water. However, the high recombination rate of electrons and holes, as well as a low reaction rate, have impeded its large-scale applications. Therefore, it is of great importance to develop appropriate photocatalysts for promoting its practical application. In this study, a novel TiO₂/SiO₂/carbon electrospun nanofiber mat (TSC NFM) with flexibility and porous hierarchy has been successfully designed and fabricated by a facile method of electrospinning and carbonization. Characterization results show that the TSC NFM consists of closely-packed and well-distributed anatase (TiO₂) nanocrystals, amorphous SiO₂ nanoparticles, and carbon with interconnected meso- and macro-pores. The photocatalytic performance of the TSC NFM was evaluated by degrading rhodamine B and 4-nitrophenol in batch systems. The results show that TSC NFM exhibits a higher photocatalytic activity than TiO₂/SiO₂ nanofiber mat, which does not contain carbon. The enhanced performance of the TSC NFM can be attributed to the improved adsorption capacity toward the organic pollutants due to the presence of carbon and to the enhanced interfacial charge separation between TiO₂ nanoparticles and carbon. Besides, the as-prepared TSC NFM displays good stability and reusability. Notably, the flexible TSC NFM can be used in a continuous-flow reactor to efficiently treat wastewater. Our work provides new insights into the fabrication of carbon-based inorganic nanofiber mats, which have great potential in water treatment.