Targeted reclaiming cationic dyes from dyeing wastewater with a dithiocarbamate-functionalized material through selective adsorption and efficient desorption

Research progress in the degradation of printing and dyeing wastewater using chitosan based composite photocatalytic materials

The surge in economic growth has spurred the expansion of the textile industry, resulting in a continuous rise in the discharge of printing and dyeing wastewater. In contrast, the photocatalytic method harnesses light energy to degrade pollutants, boasting low energy consumption and high efficiency. Nevertheless, traditional photocatalysts suffer from limited light responsiveness, inadequate adsorption capabilities, susceptibility to agglomeration, and hydrophilicity, thereby curtailing their practical utility. Consequently, integrating appropriate carriers with traditional photocatalysts becomes imperative. The combination of chitosan and semiconductor materials stands out by reducing band gap energy, augmenting reactive sites, mitigating carrier recombination, bolstering structural stability, and notably advancing the photocatalytic degradation of printing and dyeing wastewater. This study embarks on an exploration by initially elucidating the technical principles, merits, and demerits of prevailing printing and dyeing wastewater treatment methodologies, with a focal emphasis on the photocatalytic approach. It delineates the constraints encountered by traditional photocatalysts in practical scenarios. Subsequently, it comprehensively encapsulates the research advancements and elucidates the reaction mechanisms underlying chitosan based composite materials employed in treating printing and dyeing wastewater. Finally, this work casts a forward-looking perspective on the future research trajectory of chitosan based photocatalysts, particularly in the realm of industrial applications.

Removal of cationic dye pollutants from wastewater with HS loaded semi-IPN composites: kinetic and thermodynamic studies

In this study, methylene blue (MB) pollutant in water was removed using produced hazelnut shell loaded semi-interpenetrating polymer networks (HS loaded semi-IPN) adsorbent. The physical and chemical characterizations of the adsorbents were investigated using TGA, DSC, FT-IR, BET, FE-SEM, and EDX. Experimental parameters such as temperature, swelling, dye concentration, contact time, pH solution, and adsorbent dosage for MB adsorption were thoroughly investigated. It was determined that the HS loaded semi-IPN adsorbent removed 92.1% of MB dye. Subsequently, the adsorption properties between the adsorbent and dye were investigated in detail using several different kinetic, isotherm, and thermodynamic models. As a result of the obtained data, the interaction between adsorbent and dye molecules is discussed. Moreover, studies on the industrial usability of the adsorbent have been carried out, and it has been observed that the adsorbent can be employed even after four cycles.

Selective Adsorption of Methyl Orange and Methylene Blue by Porous Carbon Material Prepared From Potassium Citrate

As the discharge amount of dye wastewater increases with the development of the textile printing and dyeing industries, the treatment of the dyes in the wastewater becomes more complex. The adsorption method is a commonly used method for treating dye wastewater. The adsorbent is the key factor affecting the adsorption performance. To develop a high-performance adsorbent, a porous carbon material prepared from potassium citrate by the calcination method was applied in the adsorption of dye-containing water in this study. The morphology and pore structure of the porous carbon materials were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD), and N2 adsorption/desorption isotherm. The porous carbon material with a specific surface area of 1436 m2 g-1, PC-900, was used as an adsorbent for the adsorption of methyl orange (MO) and methylene blue (MB). The results showed that the maximum adsorption capacity of PC-900 for MO and MB reached 927 and 1853.6 mg g-1, respectively. Studies on adsorption kinetics and adsorption isotherms showed that the pseudo-second-order kinetic model and the Langmuir isotherm model were more appropriate to describe the adsorption process of MO and MB by PC-900. In addition, the results of the mixed adsorption experiment of MO and MB dyes showed that PC-900 had selective adsorption for MB.

Multifunctional pH-responsive carbon-based hydrogel adsorbent for ultrahigh capture of anionic and cationic dyes in wastewater

An environmental friendly hydrogel adsorbent (DEC@GEL) was successfully manufactured by a facile free-radical polymerization method. Multiple characterizations demonstrated that the adsorbent was rich in functional groups and porous structures. The batch and multisystem adsorption experiments were applied to systematically investigate the adsorption properties of methylene blue (MB), malachite green (MG), indigo sodium dimethyl sulfonate (IC) and tartrazine (TR) in wastewater. The experimental results proved that the kinetic and isotherms of four dyes were more consistent with the pseudo-second-order and Langmuir model, respectively. Notably, the maximum adsorption capacities of MB, MG, TR and IC at 318 K were 2186.85, 2302.53, 1766.13 and 2301.75 mg/g, respectively, which were higher than many adsorbents that had been reported. Recycle experiment demonstrated the high reusability of the DEC@GEL. The selectivity and adsorption column experiments proved that DEC@GEL was not only widely applicable to various dyes, but also provided a positive start for the industrial application. Moreover, the simulated adsorption experiments further demonstrate that DEC@GEL had the prospect of application in real industrial conditions. Finally, four adsorption mechanisms had been proposed. Various adsorption experiments had shown that DEC@GEL was not only efficient in processing dyes, but also had great potential for practical industrial applications.

Selective adsorption of anionic and cationic dyes on mesoporous UiO-66 synthesized using a template-free sonochemistry method: kinetic, isotherm and thermodynamic studies

In this study, template-free mesoporous UiO-66(U) has been successfully synthesized in shortened time by sonochemical methods and provided energy savings. The synthesized mesoporous UiO-66(U) demonstrated irregular morphology particle around 43.5 nm according to the SEM image. The N₂ adsorption-desorption isotherm indicated an irregular, 8.88 nm pore width mesoporous structure. Ultrasonic irradiation waves greatly altered mesoporous materials. A mechanism for mesoporous UiO-66(U) formation has been proposed based on the present findings. Sonochemical-solvent heat saves 97% more energy than solvothermal. Mesoporous UiO-66(U) outperformed solvothermal-synthesized UiO-66(S) in adsorption. These studies exhibited that mesopores in UiO-66 promote dye molecule mass transfer (MO, CR, and MB). According to kinetics and adsorption isotherms, the pseudo-second-order kinetic and Langmuir isotherm models matched experimental results. Thermodynamic studies demonstrated that dye adsorption is spontaneous and exothermically governed by entropy, not enthalpy. Mesoporous UiO-66(U) also showed good anionic dye selectivity in mixed dye adsorption. Mesoporous UiO-66(U) may be regenerated four times while maintaining strong adsorption capability.

Thermal Fabrication of Magnetic Fe3O4 (Nanoparticle)@Carbon Sheets from Waste Resources for the Adsorption of Dyes: Kinetic, Equilibrium, and UV-Visible Spectroscopy Investigations

Thermal treatment is applied for the direct conversion of palm stalk waste to Fe₃O₄ (np)@carbon sheets (Fe₃O₄ (np)@CSs). The effect of conversion temperature was investigated. The TEM examination of the prepared magnetic Fe₃O₄ (np)@CSs showed the formation of Fe₃O₄ (np) in a matrix of carbon sheets as a coated layer with surface functional groups including carbonyl and hydroxyl groups. Removal of dyes such as methyl orange, methylene blue, and neutral red was achieved using fabricated Fe₃O₄ (np)@CSs which were prepared at 250 °C, 400 °C, and 700 °C in a weak acidic medium. By studying the contact time effect for the adsorption of methylene blue, neutral red, and methyl orange, using the fabricated Fe₃O₄ (np)@CSs which were prepared at 250 °C and 400 °C, equilibrium occurred between 120 min and 180 min. In addition, the first-order and second-order kinetic models were applied to the adsorption data. The results revealed that the adsorption data fit better with the second-order kinetic model. Furthermore, the Freundlich model was found to be more suitable for describing the process of the separation of the dyes onto Fe₃O₄ (np)@CSs which were prepared at 250 °C and 400 °C, suggesting heterogenous surfaces and multi-layer adsorption.

A novel iron molybdate photocatalyst with heterojunction-like band gap structure for organic pollutant degradation by activation of persulfate under simulated sunlight irradiation

Advanced oxidation processes (AOPs) applied to wastewater treatment have become increasingly well developed and the ability of a single technology to remove difficult organic pollutants is limited. One of the main limiting factors is the insufficient variety and quantity of active species generated during the reaction process and catalyst failure. The coupling of the two methods is a practical and effective approach. In this study, different types of semiconductor persulfate (PS) activators, iron molybdate nanoparticles (I-FeMoO₄, II-FeMoO₄, and III-FeMoO₄), were synthesized by simple solvothermal and calcination methods and applied to photo-assisted activation of PS systems. In addition, the relationship between the intrinsic physicochemical and optoelectronic properties of FeMoO₄ and the catalytic degradation performance was revealed by a series of characterization tools, and the dominant catalysts were screened. At an unadjusted pH of 4.86, 0.6 g L^-1 of PS and 0.4 g L^-1 of I-FeMoO₄ could achieve efficient degradation of several difficult organic dye contaminants (rhodamine b (Rh B), methylene blue (MB), malachite green (MG), methyl orange (MO), and tartrazine (TTZ)) and other antibiotic contaminants (sulfamethoxazole (SMX), tetracycline (TC), norfloxacin (NOR), and carbamazepine (CBZ)) within 5-60 min. Possible degradation mechanisms in the I-FeMoO₄/PS/Light reaction system were suggested by radical trapping experiments and electron paramagnetic resonance (EPR) tests. Recovery tests demonstrated that I-FeMoO₄ has good recoverable stability and did not cause secondary pollution. Finally, our study provided a new perspective on the application of coupled wastewater treatment technologies in the practical treatment of organic wastewater.

Novel synthesis of multicomponent porous nano-hybrid composite, theoretical investigation using DFT and dye adsorption applications: disposing of waste with waste

Extensive studies have shown that doping can enhance the properties of graphene, but the application to real industrial wastewater treatment and theoretical calculations are limited. In this study, the hybrid nanoadsorbent Cu, N co-doped graphene (Cu@NG) was successfully synthesized via green route using carbon rods from waste dry batteries, human urine and copper nitrate, then multiple characterizations, detailed density functional theory (DFT) theoretical calculations and comprehensive actual wastewater tests are performed in environmental applications to investigate the adsorption properties and mechanism. The results showed that Cu@NG surface is mesoporous, decorated with CuO crystals and doped with N atoms. The isotherms and kinetics were simulated by Langmuir and pseudo-second-order models, respectively. The theoretical maximum sorption for MB and CV on Cu@NG is 116.28 mg·g^-1 and CV is 86.96 mg·g^-1, respectively. Pilot tests with Cu@NG on real textile wastewater showed that COD, BOD and color were removed by 54.2%, 55.2% and 86.4%, respectively. The desorption rate of Cu@NG is approximately above 90% for both MB and CV on Cu@NG after six cycles of treatment. The DFT calculations confirmed the experimental results as MB is more reactive than CV molecules. Besides, interactions have been systematically investigated via topology and natural bond orbital (NBO) analyses. The process mechanism involved mainly electrostatic adsorption, π-π stacking interactions and H-bonding interactions and ion exchange.

Synthesis of mesoporous-structured MIL-68(Al)/MCM-41-NH2 for methyl orange adsorption: Optimization and Selectivity

Here, we report a novel amino-modified mesoporous-structured aluminum-based metal-organic framework adsorbent, MIL-68(Al)/MCM-41-NH₂, for dye sewage treatment. The introduction of molecular sieves overcomes the inherent defects of microporous MOFs in contaminant transfer and provides more active sites to enhance adsorption efficiency. Compared with using organic amino ligands directly, this strategy is ten times cheaper. The composite was well characterized and analyzed in terms of morphology, structure and chemical composition. Batch experiments were carried out to study the influences of essential factors on the process, such as pH and temperature. In addition, their interactions and the optimum conditions were examined using response surface methodology (RSM). The adsorption kinetics, isotherms and thermodynamics were systematically elucidated. In detail, the adsorption process conforms to pseudo-second-order kinetics and follows the Sips and Freundlich isothermal models. Moreover, the maximum adsorption capacity Q_s of methyl orange (MO) was 477 mg g^-1. It could be concluded that the process was spontaneous, exothermic, and entropy-reducing. Several binary dye systems have been designed for selective adsorption research. Our material has an affinity for anionic pigments. The adsorption mechanisms were discussed in depth. The electrostatic interaction might be the dominant effect. Meanwhile, hydrogen bonding, π-π stacking, and pore filling might be important driving forces. The excellent thermal stability and recyclability of the adsorbent are readily noticed. After five reuse cycles, the composite still possesses a removal efficiency of 90% for MO. Overall, the efficient and low-cost composite can be regarded as a promising adsorbent for the selective adsorption of anionic dyes from wastewater.

Preparation and Adsorption Properties of Graphene-Modified, Pitch-Based Carbon Foam Composites

In view of the good adsorption properties of graphene and carbon foam, they were combined to achieve the optimal matching of microstructures. Taking mesophase pitch as a raw material, pitch-based carbon foam was prepared by the self-foaming method. Graphene gel was prepared as the second phase to composite with the carbon foam matrix; graphene-modified, pitch-based carbon foam composites were finally obtained. Graphene gel was dispersed in the rich pore structure of carbon foam to improve its agglomeration and the porosity, and the active sites of the composite were further increased; the adsorption properties and mechanical properties of the composites were also significantly improved. The microstructure and morphology of the composites were studied by SEM, XRD and Raman spectroscopy; the compressive property and porosity were also tested. Methylene blue (MB) solution was used to simulate a dye solution for the adsorption test, and the influence of the composite properties and MB solution on the adsorption property was studied. Results showed that the compressive strength of the composite was 13.5 MPa, increased by 53.41%, and the porosity was 58.14%, increased by 24.15%, when compared to raw carbon foam. When the mass of the adsorbent was 150 mg, the initial concentration of the MB solution was 5 mg/L, and the pH value of the MB solution was 11; the graphene-modified carbon foam composites showed the best adsorption effect, with an adsorption rate of 96.3% and an adsorption capacity of 144.45 mg/g. Compared with the raw carbon foam, the adsorption rate and adsorption capacity of the composites were increased by 158.18% and 93.50%, respectively.

Charge-controllable mussel-inspired magnetic nanocomposites for selective dye adsorption and separation

Magnetic polydopamine (PDA) nanocomposites were prepared with a facile and sustainable synthetic method. The as-synthesized polymer-based hybrid composites inherited the intrinsic adhesiveness contributed by catechol and amino moieties of PDA as well as the magnetic property of Fe₃O₄. With the unique properties of PDA, the surface charges of Fe₃O₄@PDA could be easily tuned by pH for smart adsorption-desorption behaviors. Four commercially available dyestuffs including crystal violet, rhodamine B, direct blue 71 and orange G with different structures and surface charges in solution were selected to investigate the adsorption ability and universality of Fe₃O₄@PDA in wastewater treatment. It was found that the nanocomposites could successfully adsorb these cationic and anionic dyes under suitable pH conditions. This confirmed the ability of the nanoadsorbents for the removal of common textile dyes. The dispersed magnetic nanoadsorbents also demonstrated the ease of collection from dye mixtures, and the possibility of reusing them for several cycles. Selective dye separation was found to be achievable via simple charge control without large consumption of organic solvent and energy. These bio-inspired nanocomposite adsorbents have shown high potential in wastewater treatment and selective recovery of dye waste, especially for wastewater containing ionic dyes.

Nanolayer-Constructed TiO(OH)2 Microstructures for the Efficiently Selective Removal of Cationic Dyes via an Electrostatic Interaction and Adsorption Mechanism

Efficient removal of organic dyes from contaminated water has become a great challenge and urgent work due to increasingly serious environmental problems. Here, we have for the first time prepared nanolayer-constructed TiO(OH)₂ microstructures which can present negative charge by deprotonation of the hydroxyl group to efficiently and selectively remove cationic dyes from aqueous solution through electrostatic interaction and an attraction mechanism. The nanolayer-constructed TiO(OH)₂ microstructures achieve a high adsorption capacity of 257 mg g^-1 for methylene blue (MB). The adsorption kinetics, thermodynamics, and isotherms of MB over the TiO(OH)₂ microstructures have been studied systemically. The experimental measurements and corresponding analyses demonstrate that the adsorption process of MB on TiO(OH)₂ microstructures follows a kinetic model of pseudo-second-order adsorption, agrees well with the Langmuir isotherm mode, and is a spontaneous and exothermic physisorption. Fourier transform infrared (FT-IR) spectra confirm that the prepared TiO(OH)₂ microstructures possess hydroxyl group which can deprotonate to present negative charge in solution. Further experimental studies evidently demonstrate that the TiO(OH)₂ microstructures also can remove other cationic dyes with positive charge such as basic yellow 1, basic green 4, and crystal violet but cannot adsorb anionic dye of methyl orange (MO) with negative charge in aqueous solution. The measurements for FT-IR spectra and the adsorption of cationic and anionic dyes evidently reveal that the adsorption of cationic dyes over the TiO(OH)₂ microstructures is achieved by the electrostatic interaction and attraction between TiO(OH)₂ and the dye. This work opens a strategy for the design of new absorbents to efficiently remove organic dyes from aqueous solution through an electrostatic attraction-driven adsorption process.

Hyperbranched polymers as superior adsorbent for the treatment of dyes in water

The effective control on environmental pollutants is crucial for the proper management of diverse environmental systems (e.g., soil, water, and air). In this respect, the utility of various functional materials such as hyperbranched polymers (HPs) has been recognized due to their great potentil as adsorbent for the mitigation of numerous environmental pollutants. Here, we highlight the latest progress achieved in the design and construction of HPs with high adsorption potentials. We focus on adsorption mechanisms, functionalization methods, the role of functional groups in adsorption capacity, and the choice of HPs in adsorption of cationic and anionic dyes. Recent published reports are reviewed to quantify and qualify the removal efficiency of pollutants through adsorption. We also evaluate the adsorbing efficiency of the constructed HPs and compared their performance with other such systems. The utilization potential of new materials (magnetic, polar, and biological) is highlighted along with the methods needed for their preparation and/or modification (surface, end-group, and zwitterionic) for the construction of efficient adsorbing systems. Finally, the advantages and limitations of adsorbing systems are described along with the existing challenges to help establish guidelines for future research. This article is thus expected to offer new path and guidance for developing advanced HP-based adsorbents.

Electrospun molecularly imprinted sodium alginate/polyethylene oxide nanofibrous membranes for selective adsorption of methylene blue

Molecular imprinting technique is an efficient method to improve the selective adsorption capacity for the target pollutant. In this study, sodium alginate/polyethylene oxide molecularly imprinted nanofibrous membrane (SA/PEO-MINM) with average diameter of 185 ± 20 nm was successfully synthesized by electrospinning for selective adsorption of methylene blue (MB). Benefiting from the molecular imprinted technology, the adsorption amount of SA/PEO-MINM for MB was increased by about 65%, significantly higher than the non-imprinted membrane. Results showed that the adsorption equilibrium could be well fitted with Langmuir isotherm model and the maximum adsorption capacity towards MB was 3186.7 mg/g. Kinetic experiments well complied with the Pseudo second order model. Reusability studies indicated that the removal efficiency of MB could maintain 93% of the original adsorption capacity after four consecutive adsorption/desorption cycles. More importantly, the SA/PEO-MINM with high surface area and specific adsorption recognition sites showed excellent selective adsorption capacity in the adsorption experiment of MB and methylene orange mixed dye solution. In general, the SA/PEO-MINM can be successfully applied for the selective removal of MB from dye wastewater.

Iron oxide (Fe3O4)-laden titanium carbide (Ti3C2Tx) MXene stacks for the efficient sequestration of cationic dyes from aqueous solution

We prepared two-dimensional (2D) stack-structured magnetic iron oxide (Fe₃O₄) nanoparticle anchored titanium carbide (Ti₃C₂T_x) MXene material (Ti₃C₂T_x/Fe₃O₄). It was used as a potential adsorbent to remove carcinogenic cationic dyes, such as methylene blue (MB) and rhodamine B (Rh B), from aqueous solutions. Ti₃C₂T_x/Fe₃O₄ exhibited maximum adsorption capacities of 153 and 86 mg g^-1 for MB and Rh B dyes, respectively. Batch adsorption experimental data fits the Langmuir model well, revealing monolayer adsorption of MB and Rh B onto the adsorption sites of Ti₃C₂T_x/Fe₃O₄. Additionally, Ti₃C₂T_x/Fe₃O₄ showed rapid MB/Rh B adsorption kinetics and attained equilibrium within 45 min. Moreover, Ti₃C₂T_x/Fe₃O₄ demonstrated recyclability over four cycles with high stability due to the presence of magnetic Fe₃O₄ nanoparticles. Furthermore, it exhibited remarkable selectivities of 91% and 88% in the presence of co-existing cationic and anionic dyes, respectively. Given the extraordinary adsorption capacities, Ti₃C₂T_x/Fe₃O₄ may be a promising material for the effective removal of cationic dyes from aqueous media.

A multifunctional and environmentally safe superhydrophobic membrane with superior oil/water separation, photocatalytic degradation and anti-biofouling performance

Wastewater is typically complicated with spilled oil, water soluble toxic dyes and microorganisms, making it hard to be processed and causing a significant threat to the environmental safety and human health. In this paper, we demonstrate a simple solution immersion method to obtain a multifunctional cellulose-based membrane (CBM) that possesses both superhydrophobicity with a water contact angle of 163° and superior functionalities including self-cleaning, oil-water separation, anti-biofouling, and photocatalytic degradation capabilities. The achievement of separation efficiency (96%), comparatively high flux (141 L·m^-2·h^-1) and recyclable (7 times) oil/water separation performance is attributed to the robust superhydrophobicity enabled by the synergy of metal oxide (i.e., CuO) nanostructure coating and stearic acid (SA) modification. The superhydrophobic CBM also preferentially adsorbs organic dyes in aqueous solution, e.g., methylene blue (MB), promoting their efficient decomposition (about 70.3% of MB decomposed in 3 h) with high recyclability under UV irradiation. Most remarkably, the CBM exhibits superior anti-biofouling capability and persistently resists the algae adhesion in long duration (over 20 days), as a result of the self-cleaning ability as well as the antimicrobial property of CuO nanoparticles. Our finding here paves the way to use simple, cost-effective, environmentally safe, and reliable method to fabricate multifunctional materials for wastewater treatment in complex environments.

Amidoxime modified polymers of intrinsic microporosity/alginate composite hydrogel beads for efficient adsorption of cationic dyes from aqueous solution

Polymers of intrinsic microporosity (PIM-1) has demonstrated great potential in adsorption and separation fields. In this study, PIM-1 was structured into an applicable and efficient adsorbent using a facile way. PIM-1 was first modified by amidoxime, and then the amidoxime modified PIM-1 (AOPIM-1) was mingled into alginate (Alg) hydrogel to obtain composite hydrogel beads. The AOPIM-1/Alg composite beads were further employed for removal of malachite green (MG) from aqueous solution and the effects of doped ratio, adsorbent dosage, contact time, and initial dye concentration on the MG adsorption performance were systematically investigated. The MG adsorption capacity of pure Alg beads was substantially enhanced after incorporating AOPIM-1. Furthermore, isothermal, kinetic and thermodynamic studies were performed to explore the fundamental adsorption behavior. Both Freundlich isotherm and Langmuir isotherm models can fit the adsorption isotherm data well, and the adsorption kinetics is well described by Pseudo-second-order. The adsorption process is feasible, spontaneous and endothermic. In addition, mixed dyes adsorption measurements indicate that AOPIM-1/Alg beads are highly selective to adsorb cationic dyes from anionic/cationic mixed dyes solution. The regeneration test shows that above 90% of the adsorption capacity of the composite beads can be maintained after 10 cycles of MG adsorption/desorption. These findings point that AOPIM-1/Alg composite hydrogel beads are an efficient, up-and-coming and recyclable adsorbent for cationic dyes adsorption from aqueous solution.

Assessment of a novel aminated magnetic adsorbent with excellent adsorption capacity for dyes and drugs

Dyes and drugs with high toxicity and low biodegradability pose risk to human health and ecological security, and should be purified efficiently from effluents before discharge. Traditional adsorbents are limited by the insufficient active adsorption sites and low stability. In this study, a novel aminated magnetic adsorbent (MCTs) was fabricated via two cross-linking steps using chitosan and triethylenetetramine to fill the gaps between current adsorbent and performance requirements. The morphological and physicochemical characteristics of the as-prepared MCTs were determined and identified with the aid of several characterization techniques. The adsorption performance of dyes and drugs was also investigated and represented by their adsorption capacities. In particular, the adsorption capacities of Congo Red, Chicago Sky Blue, Reactive Brilliant Red, and Ibuprofen were 583.11, 465.01, 403.12, and 291.71 mg/g, respectively. They also remained at around 80% after four reuse cycles. MCTs were adsorbed via a monolayer spontaneous chemical reaction, and hydrogen bonding and electrostatic interaction were the dominant adsorption mechanisms. These results demonstrated that the preparation of MCTs via two cross-linking steps enhanced the adsorbents' adsorption capacity, reusability, and stability. They provided a new perspective for the preparation of high-efficient adsorbents and the purification of dye- and drug-polluted wastewater.

Application of gradient acid fractionation protocol to improve decolorization technology by lignin-based adsorbent

Wastewater contaminated with dyes is discharged by huge amount daily, and involved many hazardous materials. Thus, this study focused on introducing low cost, ecofriendly and available removal agent (lignin-based adsorbent). Three adsorbents, APKL-4, APKL-5 and APKL-6 were obtained using gradient acid precipitation technology and used for methylene blue (MB) removal. The samples were characterized by SEM, FT-IR and zeta potential analyzer. The results indicated that the three adsorbents exhibit significantly different adsorption behavior due to the structural differences caused by fractionation. The APKL-5 and APKL-6 have fewer hydrophilic groups in their molecules and thus have more adsorption active sites to load MB molecules. A pore structure inside of APKL-5 molecules is form in acid fractionation, which allows it to carry more MB molecules. The adsorption capacity of APKL-5 increased 3.8 times (from 345 to 1310 mg g^-1) in the alkaline solution which showing excellent pH responsiveness. This paper presents a new promising approach for preparing high efficiency, low cost and eco-friendly adsorbents and builds a foundation for developing further applications of lignin-based adsorbents.