Opportunities and challenges in the use of coal fly ash for soil improvements--a review

Microalgae are not an umbrella solution for power industry waste abatement but could play a role in their valorization

Microalgae have long been regarded as a promising solution for biological carbon abatement from the power industry, offering renewable biomass without competing for land or water resources used for food crops. In this study, we extensively examined the application of photosynthetic microorganisms for closing carbon, nitrogen, and micronutrient loops in the power industry. Subsequently, we explored the bottom-up integration of algal biorefineries into power industry waste streams for increased economic benefits and reduced environmental impacts. Analysis of the available data indicated that microalgae integration with the power industry is primarily performed using flue-gas-assisted cultivation. This approach allows for carbon sequestration typically below one gram per liter per day, too low to significantly impact carbon abatement at achievable scales of microalgae cultivation. Alternative approaches are also being explored. For example, soluble bicarbonate platforms allow for higher biomass productivity and temporary carbon storage. Meanwhile, the use of ashes and waste heat and thermophilic strains can result in lower cultivation costs and better control of cultivation conditions. These approaches offer further incremental improvement to microalgae-based carbon abatement systems in the power industry but are unlikely to be an umbrella solution for carbon reduction. Consequently, in the near term, microalgae-based carbon valorization systems are likely to be limited to niche applications involving the synthesis of high-value products. For microalgae to truly transform carbon abatement processes radical improvements in both biology and engineering approaches are urgently needed.

Fly ash application impacts master physicochemical pedovariables: A multilevel meta-analysis

Fly ash (FA) is a very alkaline, hazardous waste with a potential to be recycled in amelioration of master pedovariables, notably: i) pH, drives soil biogeochemistry, ii) electrical conductivity (EC), reflects soil salinity level and overall soil health, iii) water holding capacity (WHC), determines soil hydraulic functions and iv) bulk denisity (BD), indicates soil compaction and water-air relations. We performed a multilevel meta-analysis, encompassing 30 out of 1325 screend studies, using a random effect model and non-aggregated data sets. By moderating; experimental type, FA application rate, soil type and land use, two distinct meta-analytical approaches on observed pedovariables were performed: i) uni-moderator, considering moderators separately, and ii) multi-moderator, considering moderators combined. It was found that FA application: increased soil pH by 15.4% (Hedge's g = 8.07), EC by 51.7% (Hedge's g = 8.07), WHC by 22.6% (Hedge's g = 7.79), and reduced BD by 13.5% (Hedge's g = -5.03). However, the uni-moderator meta-analytical model revealed a significant increase in pH and EC only with relatively lower FA dosage (up to 20%). In addition, the impact of FA on pH and EC was significantly positive in acid (pHH2O < 6.5), negative in alkaline (pHH2O > 7.2), and not significant in neutral (pHH2O = 6.6-7.2) soil types. The same uni-moderator approach revealed that FA dosages above 5% significantly increased WHC, but reduced BD. Moreover, the multi-moderator model identified two significant interactions: i) between varying FA dosage and land use, and ii) between varying FA dosage and soil type. Confirmed positive implications of FA on key soil properties underscore its strong potential as a valuable resource for sustainable soil management, mitigating widespread soil constraints and contributing waste reduction. However, careful consideration of FA dosage, soil type, and land use is imperative to optimize FA application and prevent potential adverse environmental implications.

Managing antimony pollution: Insights into Soil-Plant system dynamics and remediation Strategies

Researchers are increasingly concerned about antimony (Sb) in ecosystems and the environment. Sb primarily enters the environment through anthropogenic (urbanization, industries, coal mining, cars, and biosolid wastes) and geological (natural and chemical weathering of parent material, leaching, and wet deposition) processes. Sb is a hazardous metal that can potentially harm human health. However, no comprehensive information is available on its sources, how it behaves in soil, and its bioaccumulation. Thus, this study reviews more than 160 peer-reviewed studies examining Sb's origins, geochemical distribution and speciation in soil, biogeochemical mechanisms regulating Sb mobilization, bioavailability, and plant phytotoxicity. In addition, Sb exposure effects plant physio-morphological and biochemical attributes were investigated. The toxicity of Sb has a pronounced impact on various aspects of plant life, including a reduction in seed germination and impeding plant growth and development, resulting from restricted essential nutrient uptake, oxidative damages, disruption of photosynthetic system, and amino acid and protein synthesis. Various widely employed methods for Sb remediation, such as organic manure and compost, coal fly ash, biochar, phytoremediation, microbial-based bioremediation, micronutrients, clay minerals, and nanoremediation, are reviewed with a critical assessment of their effectiveness, cost-efficiency, and suitability for use in agricultural soils. This review shows how plants deal with Sb stress, providing insights into lowering Sb levels in the environment and lessening risks to ecosystems and human health along the food chain. Examining different methods like bioaccumulation, bio-sorption, electrostatic attraction, and complexation actively works to reduce toxicity in contaminated agricultural soil caused by Sb. In the end, the exploration of recent advancements in genetics and molecular biology techniques are highlighted, which offers valuable insights into combating Sb toxicity. In conclusion, the findings of this comprehensive review should help develop innovative and useful strategies for minimizing Sb absorption and contamination and thus successfully managing Sb-polluted soil and plants to reduce environmental and public health risks.

Bio-based resources: systemic & circular solutions for (agro)environmental services

The global promotion of decarbonisation through the circular solutions and (re)use of bio-based resources (BBR), i.e. waste streams, notably from the agricultural, forest and municipal sectors has steadily increased in recent decades. Among the transformative solutions offered by BBR, biosolids (BS), biochars (BC), and bioashes (BA) specifically attract scientific attention due to their highly complex organo-mineral matrices, which present significant potential for recovery in the agro-/forest-ecosystems. These materials enhance various soil (i) chemical (pH, macro/micro nutrient concentrations, organic matter content), (ii) physical (porosity, water-air relations, compaction) or (iii) microbial (diversity, activity) properties. Furthermore, some of transformed BBR contribute to a multitude of environmental services such as the remediation of contaminated sites and wastewater treatment, employing cost-effective and eco-friendly approaches that align with circular economy/waste management principles, ultimately contributing to climate change mitigation. However, several challenges impede the widespread utilization/transformation of BBR, including technological limitations in processing and application, concerns about contamination (e.g., PAHs, PCBs, micro/nano plastics present in BS), toxicity issues (e.g., heavy metals in BA or nanoparticles in BC), and regulatory constraints (e.g., non-uniform regulations governing the reuse of BA and BS). Addressing these challenges demands an interdisciplinary and intersectoral approach to fully unlock the potential of BBR in sustainable decarbonisation efforts.

Effect of voltage gradients on EK-PRB remediation: Experimental and molecular dynamics simulations

Electrokinetic-Permeable Reaction Barrier (EK-PRB) coupled remediation technology can effectively treat heavy metal-contaminated soil near coal mines. This study was conducted on cadmium (Cd), a widely present element in the soil of the mining area. To investigate the impact of the voltage gradient on the remediation effect of EK-PRB, the changes in current, power consumption, pH, and Cd concentration content during the macroscopic experiment were analyzed. A three-dimensional visualized kaolinite-heavy metal-water simulation system was constructed and combined with the Molecular Dynamics (MD) simulations to elucidate the migration mechanism and binding active sites of Cd on the kaolinite (001) crystalline surface at the microscopic scale. The results showed that the voltage gradient positively correlates with the current, power consumption, and Cd concentration during EK-PRB remediation, and the average removal efficiency increases non-linearly with increasing voltage gradient. Considering power consumption, average removal efficiency, and cost-effectiveness, the voltage range is between 1.5 and 3.0 V/cm, with 2.5 V/cm being the optimal value. The results of MD simulations and experiments correspond to each other. Cd2+ formed a highly stable adsorption structure in contrast to the Al-O sheet on the kaolinite (001) crystalline surface. The mean square displacement (MSD) curve of Cd2+ under the electric field exhibits anisotropy, the total diffusion coefficient DTotal increases and the Cd2+ migration rate accelerates. The electric field influences the microstructure of Cd2+ complexes. With the enhancement of the voltage gradient, the complexation between Cd2+ and water molecules is enhanced, and the interaction between Cd2+ and Cl- in solution is weakened.

Harnessing Ash for Sustainable CO2 Absorption: Current Strategies and Future Prospects

This review explores the potential of using different types of ash, namely fly ash, biomass ash, and coal ash etc., as mediums for CO2 capture and sequestration. The diverse origins of these ash types - municipal waste, organic biomass, and coal combustion - impart unique physicochemical properties that influence their suitability and efficiency in CO2 absorption. This review first discusses the environmental and economic implications of using ash wastes, emphasizing the reduction in landfill usage and the transformation of waste into value-added products. Then the chemical/physical treatments of ash wastes and their inherent capabilities in binding or reacting with CO2 are introduced, along with current methodologies utilize these ashes for CO2 sequestration, including mineral carbonation and direct air capture techniques. The application of using ash wastes for CO2 capture are highlighted, followed by the discussion regarding challenges associated with ash-based CO2 absorption approach. Finally, the article projects into the future, proposing innovative approaches and technological advancements needed to enhance the efficacy of ash in combating the increasing CO2 levels. By providing a comprehensive analysis of current strategies and envisioning future prospects, this review aims to contribute to the field of sustainable CO2 absorption and environmental management.

A field trial for remediation of multi-metal contaminated soils using the combination of fly ash stabilization and Zanthoxylumbungeanum- Lolium perenne intercropping system

Insitu stabilization and phytoextraction are considered as two convenient and effective technologies for the remediation of toxic elements (TEs) in soils. However, the effectiveness of these two remediation technologies together on the bioavailability and phytoextraction of TEs in field trials has not been explored yet. Specifically, the remediation potential of fly ash (FA; as stabilizing agent) and ryegrass (as a TE accumulator) intercropped with a target crop for soil polluted with multiple TEs has not been investigated yet, particularly in long-term field trials. Therefore, in this study, a six-month combined remediation field experiment of FA stabilization and/or ryegrass intercropping (IR) was carried out on the farmland soils contaminated with As, Cd, Cr, Cu, Hg, Ni, Pb and Zn where Zanthoxylumbungeanum (ZB) trees as native crops were grown for years. The treatments include soil cultivated alone with ZB untreated- (control) and treated-with FA (FA), produced by burning lignite in Shaanxi Datong power plant, China, soil cultivated with ZB and ryegrass untreated- (IR) and treated-with FA (FA + IR). This was underpinned by a large-scale survey in Daiziying (China), which showed that the topsoils were polluted by Cd, Cu, Hg and Pb, and that Hg and Pb contents in the Zanthoxylumbungeanum fruits exceeded their allowable limits. The TEs contents in the studied FA were lower than their total element contents in the soil. The DTPA-extractable TEs contents of the remediation modes were as follows: FA < FA + IR < IR < control. Notably, TEs contents in the ZB fruits were lowest under the FA + IR treatment, which were decreased by 27.6% for As, 42.3% for Cd, 16.7% for Cr, 30.5% for Cu, 23.1% for Hg, 15.5% for Ni, 33.2% for Pb and 38.1% for Zn compared with the control treatment. Whereas the FA + IR treatment enhanced TEs contents in ryegrass shoots and roots, and the TEs contents in ryegrass shoots were below their regulatory limits for fodder crops. The findings confirmed that the combined remediation strategy, i.e., FA (with low content of TEs) stabilization effect and intercropping of ZB (target crop) and ryegrass (accumulating plant) could provide a prospective approach to produce target plants within safe TEs thresholds with greater economic benefits, while remediating soils polluted with multiple TEs and mitigating the potential ecological and human health risk. Those results are of great applicable concern.

Recent trends in the use of fly ash for the adsorption of pollutants in contaminated wastewater and soils: Effects on soil quality and plant growth

Fly ash is one of the largest types of industrial wastes produced during the combustion of coal for energy generation. Finding efficient and sustainable solutions for its reuse has been the subject of substantial research worldwide. Here, we review the recent research data related to (i) the use of fly ash as a low-cost adsorbent for pollutants in wastewater and soils and (ii) its implications in soil-plant system. Fly ash showed prominent adsorption capacity for pollutants in water especially when it was activated or applied in composites. In addition to direct pollutant binding in soils, fly ash can enhance the soil pH indirectly increasing metals' immobilization reducing their plant uptake. Its non-selective adsorptive nature may lead to the co-adsorption of nutrients with pollutants which merits to be considered. Owing to its considerable nutrient contents, fly ash can also improve soil fertility and plant growth. The effects of fly ash on soil physico-chemical properties, microbial population and plant growth are critically evaluated. Fly ash can also contain potentially toxic contaminants (toxic metals, hydrocarbons, etc.) which could have harmful impacts on soil health and plant growth. Identifying the levels of inherent pollutants in fly ash is crucial to evaluate its suitability as a soil amendment. Negative effects of fly ash can also be addressed by using co-amendments, biological agents, and most importantly by an adequate calibration (dose and type) of fly ash based on site-specific conditions. Research directions are identified to promote the research regarding its use in wastewater treatment and agriculture.

Bio-Monitoring of Metal(loid)s Pollution in Dry Riverbeds Affected by Mining Activity

The aim of this study was to evaluate the most abundant native plants that could be used as a bio-monitor of metal(loid) concentration in dry riverbeds affected by mining activities. Three plants species and their respective rhizospheric soils were sampled from the El Beal (Piptatherum miliaceum, 15 samples), La Carrasquilla (Foeniculum vulgare, 10 samples), and Ponce (Dittrichia viscosa, 12 samples) dry riverbeds from the mining district of Cartegena-La Unión (SE Spain). There is scanty bibliography of the capacity of these species to be used as bio-monitors in the dry riverbeds. Plants categorized as a bio-monitor were established according to the bioaccumulation factor (BF), mobility ratio (MR), and linear correlations between metal(loid) concentrations in plants tissues (root or stem)-rhizospheric soils. The rhizospheric soils were highly contaminated for As, Cd, Pb, and Zn (Cf ≥ 6), and moderately contaminated for Mn (1 ≤ Cf < 3). Piptatherum miliaceum presented on Cd similar mean concentrations on rhizospheric soil and root, BF = 1.07, with a strong correlation soil-root (r = 0.61, p = 0.02). Therefore, of the three species with the capacity to grow in the area, Piptatherum miliaceum showed characteristics to be considered as a bio-monitor for Cd, with a BF > 1, and a positive-significant correlation between the rhizospheric soil and roots.

Root microbiota confers rice resistance to aluminium toxicity and phosphorus deficiency in acidic soils

Aluminium (Al) toxicity impedes crop growth in acidic soils and is considered the second largest abiotic stress after drought for crops worldwide. Despite remarkable progress in understanding Al resistance in plants, it is still unknown whether and how the soil microbiota confers Al resistance to crops. Here we found that a synthetic community composed of highly Al-resistant bacterial strains isolated from the rice rhizosphere increased rice yield by 26.36% in acidic fields. The synthetic community harvested rhizodeposited carbon for successful proliferation and mitigated soil acidification and Al toxicity through extracellular protonation. The functional coordination between plants and microbes offers a promising way to increase the usage of legacy phosphorus in topsoil. These findings highlight the potential of microbial tools for advancing sustainable agriculture in acidic soils.

Optimization of preparation of NaA zeolite from fly ash for CO2 capture

The green synthesis method of fly ash-based NaA zeolite was explored to reduce the synthesis cost and environmental hazards. For the prepared NaA samples, the effects of crystallization time, solid-liquid ratio, and Si/Al ratio were systematically studied. CO2 adsorption isotherm is used for adsorption model fitting analysis and adsorption selectivity determination. According to the experimental results, the optimized NaA zeolite synthesis conditions are as follows: the Si/Al ratio of NaA zeolite is 1.4, the solid-liquid ratio is 10, and the crystallization time is 6 h. The green synthesis method reported in this study can successfully prepare NaA zeolite and exhibit excellent CO2 adsorption performance, reaching 4.34 mmol/g, with high CO2 selective adsorption ability, reaching 89.2 for N2, 257.1 for O2, and 45.8 for CH4. The adsorbed CO2 can be released for further utilization, and NaA zeolite also has strong adsorption and regeneration performance, with a ten cycle adsorption capacity only decreasing by 1.17%. In addition, the use of cheap raw materials synthesis methods will promote the large-scale industry application of green synthesis technology in the future.

Evaluating the effects of formation and stabilization of opal/sand aggregates with organic matter amendments

Opal (SiO₂·nH₂O, amorphous silica), the by-product of alumina extraction from coal fly ash (CFA), has a strong adsorption capacity and is also an important component of clay minerals in soils. The combining of opal with sand to form artificial soils is an effective disposal strategy for large-scale CFA stockpiles and reduction of environmental risk. Nevertheless, its poor physical condition limits plant growth. Organic matter (OM) amendments have broad potential applications for water-holding and improving soil aggregation. Effects of OMs (vermicompost (VC), bagasse (BA), biochar (BC) and humic acid (HA)) on the formation, stability and pore characteristics of opal/sand aggregates were evaluated through 60-day laboratory incubation experiments. Results demonstrated that four OMs could reduce pH, with BC having the most significant effect, VC significantly increasing the electrical conductivity (EC) and TOC content of the aggregates. Except for HA, other OMs could improve the aggregates' water-holding capacity. The mean weight diameter (MWD) and percentage of >0.25 mm aggregates (R_0.25) of BA-treated aggregates were the largest, and BA had the most noticeable contribution to macro-aggregate's formation. The best aggregate stability was obtained with HA treatment, meanwhile the percentage of aggregate destruction (PAD_0.25) decreased with the addition of HA. After amendments, the proportion of organic functional groups increased, which favored aggregate's formation and stability; the surface pore characteristics were improved, with the porosity ranging from 70% to 75%, reaching the level of well-structured soil. Overall, the addition of VC and HA can effectively promote aggregates' formation and stabilization. This research may play a key role in converting CFA or opal into artificial soil. The combining of opal with sand to form artificial soil will not only solve the environmental problems caused by large-scale CFA stockpiles but will also enable the comprehensive utilization of siliceous materials in agriculture.

Contaminant containment for sustainable remediation of persistent contaminants in soil and groundwater

Contaminant containment measures are often necessary to prevent or minimize offsite movement of contaminated materials for disposal or other purposes when they can be buried or left in place due to extensive subsurface contamination. These measures can include physical, chemical, and biological technologies such as impermeable and permeable barriers, stabilization and solidification, and phytostabilization. Contaminant containment is advantageous because it can stop contaminant plumes from migrating further and allow for pollutant reduction at sites where the source is inaccessible or cannot be removed. Moreover, unlike other options, contaminant containment measures do not require the excavation of contaminated substrates. However, contaminant containment measures require regular inspections to monitor for contaminant mobilization and migration. This review critically evaluates the sources of persistent contaminants, the different approaches to contaminant remediation, and the various physical-chemical-biological processes of contaminant containment. Additionally, the review provides case studies of contaminant containment operations under real or simulated field conditions. In summary, contaminant containment measures are essential for preventing further contamination and reducing risks to public health and the environment. While periodic monitoring is necessary, the benefits of contaminant containment make it a valuable remediation option when other methods are not feasible.

Land application of industrial wastes: impacts on soil quality, biota, and human health

Globally, waste disposal options such as landfill, incineration, and discharge to water, are not preferred long-term solutions due to their social, environmental, political, and economic implications. However, there is potential for increasing the sustainability of industrial processes by considering land application of industrial wastes. Applying waste to land can have beneficial outcomes including reducing waste sent to landfill and providing alternative nutrient sources for agriculture and other primary production. However, there are also potential hazards, including environmental contamination. This article reviewed the literature on industrial waste applications to soils and assessed the associated hazards and benefits. The review investigated wastes in relation to soil characteristics, dynamics between soils and waste constituents, and possible impacts on plants, animals, and humans. The current body of literature demonstrates the potential for the application of industrial waste into agricultural soils. The main challenge for applying industrial wastes to land is the presence of contaminants in some wastes and managing these to enhance positive effects and reduce negative outcomes to within acceptable limits. Examination of the literature also revealed several gaps in the research and opportunities for further investigation: specifically, a lack of long-term experiments and mass balance assessments, variable waste composition, and negative public opinion.

Risk Evaluation of Pollutants Emission from Coal and Coal Waste Combustion Plants and Environmental Impact of Fly Ash Landfilling

Emission factors (EFs) of gaseous pollutants, particulate matter, certain harmful trace elements, and polycyclic aromatic hydrocarbons (PAHs) from three thermal power plants (TPPs) and semi-industrial fluidized bed boiler (FBB) were compared. EFs of particulate matter, trace elements (except Cd and Pb), benzo[a]pyrene, and benzo[b]fluoranthene exceed the upper limits specified in the EMEP inventory guidebook for all combustion facilities. The comparison of trace elements and PAHs content in fly ashes (FAs) from lignite and coal waste combustion in TPPs and FBB, respectively, as well as the potential environmental impact of FAs disposal, was performed by employing a set of ecological indicators such as crustal enrichment factor, risk assessment code, risk indices for trace elements, and benzo[a]pyrene equivalent concentration for PAHs. Sequential analysis shows that the trace elements portion is the lowest for water-soluble and exchangeable fractions. The highest enrichment levels in FAs are noticed for As and Hg. Based on toxic trace elements content, FAs from TPPs represent a very high ecological risk, whereas fly ash from FBB poses a moderate ecological risk but has the highest benzo[a]pyrene equivalent concentration, indicating its increased carcinogenic potential. Lead isotope ratios for Serbian coals and FAs can contribute to a lead pollution global database.

Effects of Shellfish and Organic Fertilizer Amendments on Soil Nutrients and Tea Yield and Quality

Soil acidification in tea plantations leads to an excessive heavy metal content in tea, decreasing its yield and quality. How to apply shellfish and organic fertilizers to improve soil and ensure the safe production of tea is still not clear. A two-year field experiment was conducted in tea plantations in which the soil was characterized by a pH of 4.16 and concentrations of lead (Pb) (85.28 mg/kg) and cadmium (Cd) (0.43 mg/kg) exceeding the standard. We used shellfish amendments (750, 1500, 2250 kg/ha) and organic fertilizers (3750, 7500 kg/ha) to amend the soils. The experimental results showed that compared with the treatment without any amendment (CK), the soil pH increased by 0.46 on average; the soil available nitrogen, phosphorus, and potassium contents increased by 21.68%, 19.01%, and 17.51% respectively; and the soil available Pb, Cd, Cr, and As contents decreased by 24.64%, 24.36%, 20.83%, and 26.39%, respectively. In comparison to CK, the average yield of tea also increased by 90.94 kg/ha; tea polyphenols, free amino acids, caffeine, and water extract increased by 9.17%, 15.71%, 7.54%, and 5.27%, respectively; and the contents of Pb, Cd, As, and Cr in the tea decreased significantly (p < 0.05) by 29.44-61.38%, 21.43-61.38%, 10.43-25.22%, and 10.00-33.33%, respectively. The greatest effects on all parameters occurred with the largest amendment of both shellfish (2250 kg/ha) and organic fertilizer (7500 kg/ha) combined. This finding suggests that the optimized amendment of shellfish could be used as a technical measure to improve the health quality of both soil and tea in acidified tea plantations in the future.

Does exposure to weathered coal ash with an enhanced content of uranium-series radionuclides affect flora? Changes in the physiological indicators of five referent plant species

Coal ash deposited in open landfills is a potential source of environmental pollutants due to the contained toxic element content. The weathered coal ash used in this study additionally contains enhanced activity concentrations of ²³⁸U series radionuclides. This study aimed to determine the physiological effects of enhanced ionizing radiation and toxic elements on five plant species (smilo grass, sticky fleabane, blackberry, mastic and pine tree) inhabiting the coal ash disposal site. Among the potentially toxic measured elements, contents of Sb, As and especially V significantly exceeded their respective levels at the control site, as well as the content of ²³⁸U and its progenies. Significant changes in photosynthetic pigments were recorded following chronic exposure to the plants growing on the coal ash site. Different responses were also observed in the plant species regarding the activity of catalase and glutathione-S-transferase (GST). The level of lipid peroxidation markedly increased in plants from the disposal site, except in blackberry, wherein GST activity was the strongest, indicating an important role of that enzyme in the adaptation to coal ash pollutants. The results of this study suggest that the modulation of the studied biochemical parameters in plants growing on coal ash is primarily species-dependent.

Rare-Earth Elements Extraction from Low-Alkali Desilicated Coal Fly Ash by (NH4)2SO4 + H2SO4

Coal fly ash (CFA) obtained from pulverized coal furnaces is a highly refractory waste that can be used for alumina and rare-earth elements (REEs) extraction. The REEs in this type of CFA are associated with a mullite and amorphous glassy mass that forms a core-shell structure. In this research, it was shown that complete dissolution of amorphous aluminosilicates from the mullite surface with the formation of the low-alkali mullite concentrate prior to sulfuric acid leaching with the addition of (NH₄)₂SO₄ helps to accelerate the extraction of REEs. The extraction degree of Sc and other REEs reaches 70-80% after 5 h of leaching at 110 °C and acid concentration of 5 M versus less than 20% for the raw CFA at the same conditions. To study the leaching kinetics of the process, the effects of temperature (90-110 °C), liquid-to-solid ratio (5-10), and leaching time (15-120 min) on the degrees of Al and rare-earth elements (REEs) extraction were evaluated. After 120 min of leaching at 110 °C and L/S ratio = 10, the extraction of Al was found to be lower than 30%. At the same time, total REEs (TREE) and Fe extraction were greater than 60%, which indicates that a part of the TREE was transferred into the acid soluble phase. After leaching, the residues were studied by laser diffraction (LD), X-ray diffraction (XRD), X-ray fluorescence (XRF), and scanning electron microscopy (SEM-EDS) to evaluate the leaching mechanism and the solubility of Al- and Fe-containing minerals, such as mullite, hematite, and amorphous aluminosilicate.

Application of coal fly ash in pavement subgrade stabilisation: A review

Expansive clays are found in many countries worldwide, and they exhibit inherent volume change during the seasonal moisture variation causing cracks, heaves, and damages to the overlying pavements. Chemical stabilisation is one of the most used approaches to treat the expansive clay subgrades. Cement, Lime and Fly ash are the most commonly used stabilisers, in which fly is cheaper and a by-product obtained from the coal power plant. This paper reviews fly ash stabilisation on various clay types, including low plasticity clays, high plasticity clays, silty clays, organic clays, and peats. The review begins with the properties of fly ash, followed by the characteristics of fly ash stabilised subgrades. The micro-level mechanism, physical, mechanical, and hydraulic characteristics of stabilised pavements are presented graphically for the Class C, and F fly ashes. The micro-level studies reveal that the pozzolanic reaction is stronger than the cation exchange during the fly ash stabilisation. The unconfined compressive strength (UCS), California bearing ratio (CBR) and resilient modulus (M_r) increased with the fly ash addition and curing time for most soft soils except peat clays. Based on the mechanical and hydraulic characteristics, using 15% class C fly ash with 7 days of curing is recommended for optimum performance. Although few research studies confirm that the leachate limit of stabilised soil is within the acceptable limit, further studies are required to investigate the uptake of heavy metals and other certain carcinogenic contaminants. This study will provide key information for researchers and Engineers on the selection of fly ash stabilisation measures for expansive subgrades.

Synergism of Industrial and Agricultural Waste as a Suitable Carrier Material for Developing Potential Biofertilizer for Sustainable Agricultural Production of Eggplant

The study investigates biochar from agriculture waste and flyash from coal power station as possible carrier materials for two plant growth-promoting (PGP) bacterial strains Burkholderia sp. L2 and Bacillus sp. A30 for enhanced eggplant growth and yield. Biochar-based biofertilizers with/without flyash showed higher viability up to 270 days of storage period. The maximum percentage of seed germination was observed in L2-based biochar and flyash + biochar (1:1) bifertilizer. Moreover, the L2 + biochar+flyash produced a maximum percentage increase in fruit yield with significant (p < 0.05) improvement in plant growth parameters. Post-harvest soil status also showed enhanced physical (water holding capacity, moisture content), chemical (pH, electrical conductivity, NPK), and dehydrogenase activity. The study suggests that biofertilizer of L2 strain with agriculture waste generated biochar and flyash as carrier materials can tremendously enhance the productivity of eggplant and could act as a substitute for chemical fertilizer thus solving their disposal problem by sustainable waste management.

1H-NMR and LC-MS Based Metabolomics Analysis of Potato (Solanum tuberosum L.) Cultivars Irrigated with Fly Ash Treated Acid Mine Drainage

1H NMR and LC-MS, commonly used metabolomics analytical platforms, were used to annotate the metabolites found in potato (Solanum tuberosum L.) irrigated with four different treatments based on FA to AMD ratios, namely: control (0% AMD; tap water), 1:1 (50% AMD), 3:1 (75% AMD is 75% FA: AMD), and 100% AMD (untreated). The effects of stress on plants were illustrated by the primary metabolite shifts in the region from δH 0.0 to δH 4.0 and secondary metabolites peaks were prominent in the region ranging from δH 4.5 to δH 8.0. The 1:3 irrigation treatment enabled, in two potato cultivars, the production of significantly high concentrations of secondary metabolites due to the 75% FA: AMD content in the irrigation mixture, which induced stress. The findings suggested that 1:1 irrigation treatment induced production of lower amounts of secondary metabolites in all crops compared to crops irrigated with untreated acid mine drainage treatment and with other FA-treated AMD solutions.

Applicability of Ash Wastes for Reducing Trace Element Content in Zea mays L. Grown in Eco-Diesel Contaminated Soil

Among the large group of xenobiotics released into the environment, petroleum derivatives are particularly dangerous, especially given continuing industrial development and the rising demand for fuel. As increasing amounts of fly ash and sewage sludge are released, it becomes necessary to explore new methods of reusing these types of waste as reclamation agents or nutrient sources. The present study examined how soil contamination with Eco-Diesel oil (0; 10; 20 cm3 kg−1 soil) affected the trace-element content in the aerial parts of maize. Coal and sludge ashes were used as reclamation agents. Our study revealed that diesel oil strongly affected the trace-element content in the aerial parts of maize. In the non-amended group, Eco-Diesel oil contamination led to higher accumulation of the trace elements in maize (with the exception of Pb and Ni), with Cu and Mn content increasing the most. The ashes incorporated into the soil performed inconsistently as a reclamation agent. Overall, the amendment reduced Mn and Fe in the aerial parts of maize while increasing average Cd and Cu levels. No significant effect was noted for the other elements.

The Removal of Atrazine and Benalaxyl by the Fly Ash Released from Kosovo A Power Plant

The development of low-cost adsorbent coal FA (Kosovo A) for pesticide removal is an important area of scientific research. With this study, we show the potential of adsorption of coal FA (Kosovo A) for the removal of benalaxyl and atrazine from water. We have found that the amount of adsorbed benalaxyl and atrazine increases with an increasing amount of coal FA (Kosovo A) in solution. The maximum capacity coal FA (Kosovo A) to adsorb benalaxyl and atrazine was found to be 0.46 and 0.45 mg/g according to the Freundlich equation and 3.48 and 3.33 mg/g according to the Langmuir equation. The Freundlich adsorption equation better explains the adsorption results of pesticides (benalaxyl and atrazine) in coal FA (Kosovo A), as the values of the recovery coefficient (R2) were higher in Freundlich equation than the Langmuir equation. The adsorption isotherms were of type L and show that the adsorption efficiency of the coal FA (Kosovo A) depends on the initial concentration of benalaxyl and atrazine in solution and the maximum removal of benalaxyl and atrazine was achieved at concentrations less than 10 µg/ml. This study’s results are expected to have implications for the use of coal FA (Kosovo A) for the removal of pesticides from water.

Fly Ash as an Ingredient in the Contaminated Soil Stabilization Process

Fly ash is the main by-product of coal combustion characterized by a large specific surface area. In addition to oxides, it also contains unburned coal and trace elements. This study aimed to investigate the possibility of using fly ash from pit-coal combustion (CFA) for the treatment of benzene-contaminated soil (S). The CFA was used as a mixture with Portland cement (PC) (70% PC + 30% CFA). The soil was treated with a PC-CFA mixture in amounts of 40, 60, and 80% of soil mass. During the process, the concentration of benzene was monitored with the flame-ionization detector. Produced monoliths (S+(PC-CFA)x) were tested for compressive strength and capillary water absorption. The experiment confirmed that the PC-CFA mixture limited benzene emission. The highest reduction in benzene concentration (34–39%) was observed for samples treated with the PC-CFA mixture in an amount of 80% (S+(PC-CFA)80). The average compressive strength of monoliths S+(PC-CFA)40, S+(PC-CFA)60, and S+(PC-CFA)80 was 0.57, 4.53, and 6.79 MPa, respectively. The water absorption values were in the range of 15–22% dm.

Effects of Coal and Sewage Sludge Ashes on Macronutrient Content in Maize (Zea mays L.) Grown on Soil Contaminated with Eco-Diesel Oil

Petroleum hydrocarbons, as aggressive components of diesel oils, after migration to the land environment can alter the activity and efficiency of ecosystems. They can also be dangerous to animal and human health. Eco-friendly methods for the reclamation of affected soils is necessary to manage degraded lands. One such method is the use of ashes. The aim of this research was to determine how soil pollution with diesel oil (brand name, Eco-Diesel) affects the chemical composition of maize (Zea mays L.) and whether the application of ash from a combined heat and power plant, as well as from sewage sludge incineration, could reduce the potentially adverse impact of diesel oil on plants. The research results demonstrated that soil contamination with Eco-Diesel oil modified the content of selected macronutrients in the analyzed crop plant. Eco-Diesel oil had a negative effect on maize yield. The highest diesel oil dose in a series without neutralizing substances had a positive effect on the accumulation of most elements, except nitrogen and sodium. Soil enrichment with ash differentiated the content of macronutrients, mainly nitrogen and phosphorus, in the aerial biomass of maize. The ashes increased the yield of maize and content of some macronutrients, mainly nitrogen but also calcium, the latter in a series where soil was treated with ash from sewage sludge thermal recycling. Both types of ash also resulted in a decrease in the plant content of phosphorus, while ash from hard coal caused a slight reduction in the content of potassium in maize. Ash of different origins can be an effective solution in the reclamation of degraded soils, which may then be used for growing energy crops.

Interactive effect of Meloidogyne incognita and fly ash on the growth, physiology, and antioxidant properties of carrot (Daucus carota L.)

Alternative methods are needed to replace chemical nematicides because they have the potential to damage beneficial soil microbial diversity. Therefore, the present work was done to elucidate the soil ameliorative, plant-growth-promoting, and nematicidal properties of fly ash. A random block-designed pot experiment was conducted during the period, December 2018-February 2019. Seeds of carrot (Daucus carota L.) were sown under natural conditions in clay pots containing a growth medium comprising of field soil amended with different levels of fly ash. Plants were inoculated with Meloidogyne incognita that were molecularly characterized using 18S and D2/D3 fragments of 28S rDNA and morphologically through perineal pattern arrangement. The results revealed that fly ash application improved the soil's important physicochemical characteristics. The inoculation of M. incognita significantly reduced the plant growth, yield, and pigment content of carrot compared to the untreated uninoculated plants. Carrot grown in 15% fly ash (85:15 w/w field soil:fly ash) growth substrate had significantly (P ≤ 0.05) improved plant growth, yield, and pigment content as compared to the untreated inoculated plants. Moreover, the proline content and the activity of superoxide dismutase (SOD) and catalase (CAT) were enhanced by applying 15% fly ash. Fly ash amendment to the soil not only improved plant growth and yield but also reduced the gall index and egg mass index per root system of the carrot as well. Our results, therefore, suggest that 15% fly ash can be used in a sustainable way to improve the growth, yield, and resistance of carrot against the infection of M. incognita.

Application of different alkaline materials as polluted soil amendments: A comparative assessment of their impact on trace element mobility and microbial functions

Treatment with chemical amendments is among the best techniques to remediate soils highly polluted with trace elements. The use of waste-derived products has several advantages in this regard, mainly in terms of reducing process costs and conserving natural resources. In this study, the performance of the synthetic zeolite NaP1 derived from coal combustion fly ash (SZ) and the by-product generated from the processing of aluminum salt slags (BP) was evaluated with this aim in comparison to calcite (CC). For this purpose, mine soils polluted with Zn, Cd, and Pb were amended under controlled laboratory conditions with different doses (0%, 1%, 2%, 5%, and 10%) of SZ, BP, or CC, and their impact on trace element mobility and microbial functions was evaluated. Specifically, the mobile and mobilizable trace element pools, basal soil respiration, and different enzyme activities were analyzed. Both SZ and BP performed better than CC in the immobilization of trace elements, reaching, respectively, mobility decreases up to 89-94% and 66-87% when applied at a dose of 10%. These amendments reduced the mobile trace element pool by precipitating them as acid-soluble precipitates and/or retaining them in the reducible fraction of soils. The alkaline nature of these materials and the concomitant increase in soil pH caused by their application mainly accounted for this behavior. Additionally, soil microbial functionality improved after amendment, especially in the case of SZ, as shown by dehydrogenase and alkaline phosphatase activities, which significantly increased (p < 0.05) up to 536% and 48%, respectively. Therefore, applying SZ or BP as soil amendments can significantly decrease the mobile trace element contents of heavily polluted soils without negatively affecting soil quality, thus facilitating plant growth to revegetate and reclaim degraded spaces.

Multi-element Interactive Improvement Mechanism of Coal Fly Ash-Based Soil Conditioner on Wheat

Globally, coal fly ash (CFA) is a bulk industrial solid waste that is difficult to be disposed of, which posed serious environmental risks to the atmosphere, water, and soil. Besides, the food crisis outbreaks worldwide. In this case, the utilization of CFA to produce soil amendments is expected to improve the soil quality and to increase the grain yield. This paper took the soil conditioner prepared by chemical activation method as the research object, analyzed, and found out its mechanism when increasing the yield and improving the quality of crops. First, the simulated hydroponics method was used to identify the key yield-increasing factors in the soil conditioner as well as the effects of those factors by taking the plant height, stem thickness, dry weight, and fresh weight of wheat as indicators at the early stage of growth. Then, SPSS was used to analyze the interaction among K, P, and other four middle trace elements in the stem and the leaf of wheat. The results showed that for wheat seedlings, there were strong interactions between Fe and Mg, Mg and Ca, and Ca and Si. Fe had a significant enhancement effect on the fresh weight of wheat seedlings. Mg had a significant enhancement effect on both the fresh weight and dry weight of wheat seedlings. Si can greatly enhance the dry weight and plant height, and Ca can greatly increase the stem thickness. It was also found that the soil conditioner and the basic N, P, and K fertilizer had a good mutual promotion effect. Among the four elements, Mg and Si are the key growth factors. When the nutrient elements were relatively poor, the increase of Mg by 50% would lead to the growth of the fresh weight of wheat seedlings by 65%; when the content of active Si increased by 50%, the fresh weight would increase by 52%. Therefore, the soil conditioner prepared by modified treatment of CFA owns a good application prospect to increase the yield and quality of crops.

Co-pyrolysis of corn stover with industrial coal ash for in situ efficient remediation of heavy metals in multi-polluted soil

Coal ash incorporated biochar (CA/BC) composite was prepared by co-pyrolysis of agricultural residue and industrial coal ash and applied for remediation of soils polluted by lead (Pb) and cadmium (Cd). The results showed that immobilization efficiency of CA/BC for heavy metals (HMs) was significantly enhanced by 77.1 % (Pb) and 42.7 % (Cd) compared to pristine biochar (BC), and this was mainly due to the increased pH value, surface functionality and surface negative charge. By the introduction of 5 % CA/BC, the polluted soils showed the highest reduction of leaching toxicity by 67.9 % (Pb) and 49.7 % (Cd), respectively. The chemical speciation of Pb and Cd in soils was changed remarkably and the reduced bioavailable Pb and Cd were mainly transformed from acid-soluble fraction into the most stable form of residual fraction. The mechanism study showed that surface precipitation, complexation, cation exchange and cation-π interaction of CA/BC mainly contributed to heavy metals (HMs) immobilization. The pot experiments further confirmed that incorporation of 5 % CA/BC effectively reduced plant Pb and Cd accumulation by 81 % and 62.5 % respectively, and significantly promoted the plant growth of paddy rice by 3.1, 2.2 and 2.0 times in terms of root, stem length and dry mass parameters. The present study offered a cost-effective and green method to prepare soil amendment with great potential for remediation of soils polluted by HMs and realized the value-added utilization of waste agricultural residue and industrial coal ash.

Enhanced Performance of Fly Ash-Based Supports for Low-Cost Ceramic Membranes with the Addition of Bauxite

Support is a necessary foundation for ceramic membranes to achieve high performance. Finding the optimum balance between high performance and low cost is still a significant challenge in the fabrication of ceramic supports. In this study, low-cost fly ash-based ceramic supports with enhanced performance were prepared by the addition of bauxite. The pore structure, mechanical strength, and shrinkage of fly ash/bauxite supports could be tuned by optimizing the bauxite content and sintering temperature. When the sintering temperature and bauxite content were controlled at 1300 °C and 40 wt%, respectively, the obtained membrane supports exhibited a high pure water permeance of approximately 5.36 m³·m^-2·h^-1·bar^-1 and a high bending strength of approximately 69.6 MPa. At the same time, the optimized ceramic supports presented a typical mullite phase and excellent resistance to acid and alkali. This work provides a potential route for the preparation of ceramic membrane supports with characteristics of low cost and high performance.

The Behaviour of Rare Earth Elements from South African Coal Fly Ash during Enrichment Processes: Wet, Magnetic Separation and Zeolitisation

Rare earth elements (REEs) are essential raw materials in a variety of industries including clean energy technologies such as electric vehicles and wind turbines. This places an ever-increasing demand on global rare earth element production. Coal fly ash (CFA) possesses appreciable levels of REEs. CFA, a waste by-product of coal combustion, is therefore a readily available source of REEs that does not require mining. CFA valorisation to zeolites has been achieved via various synthesis pathways. This study aimed to evaluate one such pathway by monitoring how REEs partition during CFA processing by the wet, magnetic separation process and zeolitisation. South African CFA was subjected to wet, magnetic separation and subsequent zeolitisation of the nonmagnetic fraction (NMF); solid products were characterised by XRD, SEM, XRF and LA-ICP-MS. The wet, magnetic separation process resulted in the partitioning of a specific set of transition metals (such as Fe, Mn, Cr, V, Ni, Zn, Cu, Co and Mo) into the magnetic fraction (MF) of CFA, while REEs partitioned into the NMF with a total REE content of 530.2 ppm; thus, the matrix elements of CFA were extracted with ease. Zeolitisation resulted in a solid zeolite product (hydroxysodalite) with a total REE content of 537.6 ppm. The process of zeolitisation also resulted in the selective enrichment of Ce (259.1 ppm) into the solid zeolite product (hydroxysodalite), while other REEs were largely partitioned into the liquid phase. CFA valorisation by wet, magnetic separation and zeolitisation therefore allowed for the partitioning of REEs into various extraction products while recovering the matrix elements of CFA such as Fe, Si and Al. The findings of this study highlight the geopolitical importance of REEs in terms of the development of alternative processes for REE recovery from waste and alternative sources, which may potentially give countries that employ and develop the technology a key advantage in the production of REEs for the global market.

Simple and rapid quantification of chromium, arsenic, and selenium in bituminous coal samples using a desktop energy dispersive X-ray fluorescence analyzer

In this study, the simple and rapid quantification of Cr, As, and Se in bituminous coal was achieved by energy dispersive X-ray fluorescence (EDXRF) spectrometry using pressed and powdered samples. The accuracy of the EDXRF method was improved by spectral processing optimization so the net intensity of the analytical X-ray line reflected the actual value. The EDXRF method provides results that are comparable to those obtained using traditional chemical analysis methods with two types of samples and it reduces the analysis time by 66% for pellet samples and 90% for powder samples.

Recycling of Coal Fly Ash as an Example of an Efficient Circular Economy: A Stakeholder Approach

The scale of waste formation from coal-fired generation is significant and tends to grow steadily in the context of the global use of coal for power production. This paper covers the problems and current opportunities for recycling coal fly ash waste from coal generation from the position of a stakeholder approach, namely, identification of the main participants and determination of the effects for economic agents in coal fly ash recycling projects. Based on the method of economic modeling and the empirical assessment of project efficiency, this paper presents alternative patterns of stakeholder interaction in the process of implementing coal fly ash recycling projects, estimates the effects of using coal fly ash, and identifies conflicting interests between stakeholders. It is shown that the reason behind the low interest of the Russian private sector in the processing of coal fly ash is the lack of stimulating market mechanisms for manufacturers and consumers of ash products, the high risks of implementing recycling projects based on clean coal technologies, and low environmental payments for commercial companies.

Immobilization persistence of Cu, Cr, Pb, Zn ions by the addition of steel slag in acidic contaminated mine soil

Adding steel slag to the acidic contaminated mine soil can immobilize heavy metal ions, but immobilization persistence of the metal ions needs to be determined. In this study, dynamic column simulation experiments were set up to compare the immobilization persistence of Cu, Cr, Pb and Zn ions in original soil and with the addition of slag, lime or fly ash to the soil during a simulated 36-month of acid rain leaching. After adding slag and lime, the pH, organic matter content and cation exchange capacity of soil were significantly increased. Compared with the original soil, additions of slag and lime to the soil were able to persistently immobilize the metal ions, whereas fly ash additions had little effect. During simulation, the metal ion concentrations in the slag group leaching solution were essentially consistent with Standard IV for groundwater. The metal ions were immobilized to form instable hydroxides and stable fractions following adding slag to soil. The hydroxide could rerelease metal ions by acid rain leaching, part of which were re-immobilized into stable fractions by entering slag lattice and complexing with soil organic matter. Therefore, adding slag to soil can persistently immobilize metal ions for heavy metal-contaminated acidic mine soil.

Isothermal drying kinetics of sewage sludge using weathered coal fly ash as adjuvant for agronomic application

This study aims to evaluate the effect of weathered coal fly ash (CFA) as a drying adjuvant of sewage sludge (SS) to produce a soil amendment. The high amount of SS and CFA creates a complex waste management problem in many countries, requiring more research efforts. Towards a circular economy, CFA can be viewed as an anthropogenic inorganic by-product with valuable nutrients (e.g. K), which can be recovered in combination with SS (rich in organic matter, N, and P). Different temperatures (70, 85, 100, 115, and 130 °C) are tested to dry small SS cylinders, without and with 0.15 g CFA g^-1 of SS_{wet basis (wb)}. By fitting appropriate models to the experimental drying curves, it is possible to observe an improvement of 1-17% in the diffusion coefficient and 7-19% in the kinetic constants, using CFA. The best drying conditions are achieved with CFA as an adjuvant at 130 °C, where the drying rate is 31.61 gH₂O kg^-1 SS_wb min^-1. Phytotoxicity and growth assays are performed to evaluate the effect of the produced materials in the soil. The product with SS and CFA shows the potential to improve soil condition due to (i) the organic matter, N, P, and K content, (ii) the lower phytotoxic effect when compared to raw SS; (iii) the soil pH correction. Thus, not only the addition of weathered CFA facilitates the drying of SS but also the final product has benefits to soil conditions.

Zeolite NaP1 Functionalization for the Sorption of Metal Complexes with Biodegradable N-(1,2-dicarboxyethyl)-D,L-aspartic Acid

The possibility of application of chitosan-modified zeolite as sorbent for Cu(II), Zn(II), Mn(II), and Fe(III) ions and their mixtures in the presence of N-(1,2-dicarboxyethyl)-D,L-aspartic acid, IDHA) under different experimental conditions were investigated. Chitosan-modified zeolite belongs to the group of biodegradable complexing agents used in fertilizer production. NaP1CS as a carrier forms a barrier to the spontaneous release of the fertilizer into soil. The obtained materials were characterized by Fourier transform infrared spectroscopy (FTIR); surface area determination (ASAP); scanning electron microscopy (SEM-EDS); X-ray fluorescence (XRF); X-ray diffraction (XRD); and carbon, hydrogen, and nitrogen (CHN), as well as thermogravimetric (TGA) methods. The concentrations of Cu(II), Zn(II), Mn(II), and Fe(III) complexes with IDHA varied from 5-20 mg/dm³ for Cu(II), 10-40 mg/dm³ for Fe(III), 20-80 mg/dm³ for Mn(II), and 10-40 mg/dm³ for Zn(II), respectively; pH value (3-6), time (1-120 min), and temperature (293-333 K) on the sorption efficiency were tested. The Langmuir, Freundlich, Dubinin-Radushkevich, and Temkin adsorption models were applied to describe experimental data. The pH 5 proved to be appropriate for adsorption. The pseudo-second order and Langmuir models were consistent with the experimental data. The thermodynamic parameters indicate that adsorption is spontaneous and endothermic. The highest desorption percentage was achieved using the HCl solution, therefore, proving that method can be used to design slow-release fertilizers.

Influence of mycorrhiza and fly ash on the survival, growth and heavy metal accumulation in three Acacia species grown in Cu-Ni mine soil

Acacia albida, Acacia luederitzii, and Acacia tortilis are dominant acacia species in Botswana and have the potential to rehabilitate the heavy metal degraded environment. To establish this claim, experiments to assess the influence of mycorrhizal inoculation and fly ash amendments on the survival, growth and heavy metal accumulation of these species in mine tailings were conducted. A two-factor (AM inoculation × fly ash) in CRD was done on each of the three Acacia species consisting of four treatments: control (no mycorrhizal, no fly ash coded as - AM/- FA), with mycorrhizal but no fly ash (+ AM/- FA), no mycorrhizal but with fly ash (- AM/+ FA), and with mycorrhizal and with fly ash (+ AM/+ FA). After 24 weeks, results showed that the survival and dry matter yield of all Acacia species were enhanced by 10% with fly ash amendments. However, mycorrhiza inoculation alone improved the survival of A. albida and A. luederitzii but reduced that of the A. tortilis in mine tailings. Fly ash amendments increased the pH of the mine tailings, reduced the availability of Cu, Ni, Pb, Mn and Zn and consequently reduced the concentration of these metals in shoots. On the other hand, it increased the availability of As in the mine tailings. In addition, mycorrhizal inoculation reduced the concentration of these metals in shoots regardless of fly ash amendments. Overall, combined mycorrhizal inoculation and fly ash amendment enhanced the establishment of A. luederitzii in heavy metal-contaminated soils by reducing the heavy metal availability and metal uptake, thus increasing the survival and dry matter yield of plants.

Utilization of coal fly ash in China: a mini-review on challenges and future directions

The rapid economic development in China places a large demand for energy, and as a result, thermal power plants in China are producing an enormous amount of coal fly ash (CFA) which causes severe environmental pollution. This paper briefly describes the current production and utilization status of CFA in China and identifies the challenges confronting sustainable CFA utilization as the Chinese economy is being transformed. These issues include a regional imbalance in supply and demand, reducing demand in the real estate industry as well as stricter laws for environmental protection. Viable directions for future CFA utilization are proposed, for example, production of CFA-based ceramic tiles, recovery of elemental resources, agricultural melioration, treatment of wastewater and flue gas, and production of high-volume CFA concretes. This paper has some guiding significance for sustainable and cleaner utilization of CFA in China and even worldwide. Graphical abstract.

Recent Trends in Sustainable Remediation of Pb-Contaminated Shooting Range Soils: Rethinking Waste Management within a Circular Economy

Soil metal contamination in recreational shooting ranges represents a widespread environmental problem. Lead (Pb) is the primary component of traditional ammunition, followed by metalloids such as antimony (Sb) and arsenic (As). Lead-based bullets and pellets deposited on the soil surface are subject to steady weathering; hence, metal(loid)s are released and accumulated in the underlying soil, with potential adverse consequences for ecosystem function and human health. Amongst the currently available environmentally-safe technologies for the remediation of metal-contaminated soils, chemical immobilization is recognized as the most practical and cost-effective one. This technology often uses inorganic and organic amendments to reduce metal mobility, bioavailability and toxicity (environmental benefits). Likewise, amendments may also promote and speed up the re-establishment of vegetation on metal-affected soils, thus facilitating the conversion of abandoned shooting ranges into public green spaces (social benefit). In line with this, the circular economy paradigm calls for a more sustainable waste management, for instance, by recycling and reusing by-products and wastes in an attempt to reduce the demand for raw materials (economic benefit). The objective of this manuscript is to present a state-of-the-art review of the different industrial and agro-food by-products and wastes used for the remediation of metal-contaminated shooting range soils.

The influences of fly ash on stabilization for Cd in contaminated soils

Soil contaminated with potentially toxic metals (PTMs) has being a global environmental issue, which needs to be addressed on the priority basis. Fly ash (FA) is a kind of low-cost alkaline materials, which has been widely used in remediation of soil contaminated by PTMs, while the effects of FA on the stability for PTMs in contaminated farmland soil are still not clearly evaluated. In this study, cadmium (Cd) contaminated soil samples, collected from Shaanxi (SX), Hubei (HB), and Zhejiang (ZJ) province of China, were amended with FA addition (0, 1%, 2.5%, 5%, and 10% dose), and 1-year changes of Cd availability in soil samples were focused on. In addition, biological assessment method through pot culture was carried out to evaluate the reuse potential of Cd contaminated soils amended by FA. The result indicated that FA had a notable impact on decreasing the Cd mobility of SX soil (sand type), with 18.2~52.1% reduction in the DTPA extractable solution, followed by HB soil with 5.9~16.7% reduction, but no obvious effect of FA on ZJ soil (clay type) was observed. Furthermore, the results of pot experiment revealed that FA application could increase the biomass of Chinese cabbage. However, the DTPA extractable Cd in soils after planation and the Cd accumulation of plant increased. The results revealed that FA was not a promising soil stabilizer to immobilize HMs in Cd contaminated soil, and careful consideration should be given to Cd contaminated soils with FA restoration especially in their using for farmland productive due to the remaining risk of Cd bioavailability. These results also contributed to provide references for similar soil pollution remediation.

The Effect of a Fly Ash-Based Soil Conditioner on Corn and Wheat Yield and Risk Analysis of Heavy Metal Contamination

The utilization of coal fly ash (CFA) as a soil conditioner has been a research hotspot in recent years. In this paper, the continuity and stability of the yield-increasing effect of a fly ash-based soil conditioner were investigated through field trials for three consecutive years. The yield-increasing effect and applicability were also investigated by planting a variety of crops in different types of soil. Field test results revealed that the new fly ash-based soil conditioner had wide adaptability and stability under the condition of reducing the application of traditional fertilizers by 20%. For corns grown in castano-cinnamon soil and dark brown soil, the application of the new fly ash-based soil conditioner for three consecutive years has steadily increased the yield by more than 10%. The yield of wheat planted in castano-cinnamon soil also increased by 15%. Additionally, considering that heavy metals (HMs) contained in the fly ash-based soil conditioner may cause environmental contamination, this paper calculated and analyzed the bio-concentration factor (BCF) and the translocation factor (TF) of Cr, As, Cd, Hg and Pb in the corn experimental fields. The results showed that the five heavy metals were not significantly enriched in various parts of the corn stalk after application of the soil conditioner, and there was temporarily no environmental risk in terms of returning straws to the field or raising livestock.

Study of the remediation effects of passivation materials on Pb-contaminated soil

The passivation effects of blast furnace slag, fly ash, corncob biochar, and phosphate fertilizer in Pb-contaminated soil was evaluated against the soil pH, available Pb content, Pb fractions, and bioactivity coefficient. Blast furnace slag and fly ash could increase soil pH, while corncob biochar and phosphate fertilizers lowered soil pH. The available Pb content in the blast furnace slag and phosphate fertilizer treatment groups was significantly lower than in other treatments. Also, blast furnace slag and phosphate fertilizer could significantly convert nonresidual Pb into residual Pb. Combined with the environmental impact after application and cost of the material, it is recommended that blast furnace slag can be used as a passivation agent for low-concentration Pb-contaminated soil.

Treatment of Coal Fly Ash and Environmentally Friendly Use with Rubber in Cable Wires as Insulation Material

Energy demand is increasing all over the world, and to fulfill this need, more energy is required to be produced. Coal power plants produce around 39% of energy, but during energy production, these coal power plants also generate waste in the form of coal fly ash (CFA). The reuse of CFA is the only solution to control this waste; fly ash can be used in different products. Therefore, this study utilizes CFA with rubber as filler materials in the rubber industry. There are different techniques (such as nozzle design technology, air classifier, and optimization of CFA to convert crushed fly ash into valuable microparticles. Treated CFA is applied to produce medium voltage insulated cables and fire resistance cables with different kinds of rubber, such as styrene–butadiene and Ethylene–propylene. The study found that by applying CFA in insulated cables, the elongation at break increased by 50%, and volume resistance 2.2 × 1016 Ω·cm, insulation resistance increased 70% by using CFA with magnesium in the recipe of insulated cables. The CFA increased the collection rate of cleaning by 30% using this technology, and product life expectancy increased by 5–20%.

Application of ash and municipal sewage sludge as macronutrient sources in sustainable plant biomass production

Owing to the growing volumes of ash and sewage sludge waste, there is a requirement for theoretical and practical research into the use of these wastes as a source of nutrients. However, there are relatively few studies on the transfer of macronutrients in soil-plant systems amended with ash-sewage sludge mixtures under field conditions. The aim of the study was to determine the effect of bituminous coal ash (AC), biomass ash (AB), and municipal sewage sludge (MSS) on the quantity and quality of a grass-legume mixture. During a 6 year field experiment on a sandy loam soil treated with the wastes, applied as mixtures or separately, the plant yield; N, P, K, Na, Mg, and Ca uptake by plants; macronutrient content and ratios in the plant biomass; and the recovery rate of macronutrients by plants were evaluated. The AB-MSS treatment increased the yield in comparison to that where the wastes were applied separately. The N, P, and Ca contents in the plant biomass and N and P uptake under ash-sludge treatments were in the range observed for the ash and sewage sludge. The AB-MSS co-application resulted in the highest K uptake. The AC-MSS treatment increased K and Mg uptake in relation to AC treatment. When AC or AB was added to the MSS, the Ca uptake increased relative to the MSS treatment. The plant biomass under the AB treatment was optimal for biofuel purposes in terms of the chemical composition. The co-application of AC or AB with MSS resulted in the optimum Ca:Mg ratio for fodder purposes. The recovery rate of the macroelements decreased in the following order: K, N, P, Mg, Na, and Ca. The results support the co-application of solid wastes such as ash and municipal sewage sludge to improve productivity, support the recycling of macronutrients, improve sustainability through the reduction of ash and sewage sludge disposal, and reduce reliance on mineral fertilizer.

Reduction of heavy metals leaching and pore volume in high-volume fly ash cement pastes by adding nano-SiO2

This study investigated the compressive strengths and leaching of heavy metals in high-volume fly ash cement (HVFAC) pastes with and without nano-SiO₂ (NS). Further, scanning electron microscopy, X-ray diffraction, and mercury intrusion porosimetry were used to characterize the microstructure of the specimens. The results showed that the addition of NS increased the compressive strength of HVFAC specimens. NS accelerated the hydration of both cement and fly ash to form more hydration products, and it reacted with portlandite to simultaneously generate more C-S-H gel. Thus, the total pore volume, especially the capillary pores, in the NS-mixed HVFAC specimens was reduced, and their microstructure became denser because of the filling of more hydration products in the pores. This resulted in the reduction of the leaching of heavy metals (Cr, Pb, Cd, As, Zn, and Cu) in the NS-mixed HVFAC specimens compared with the HVFAC specimen containing no NS. According to the Chinese national standard (GB 3838-2002), the water quality of leachates from the HVFAC specimens mixed with both 3% and 5% NS reached grade I, thus causing nearly no harm to the water and soil environment.

Assessment of hazardous property HP 14 using ecotoxicological tests: a case study of weathered coal fly ash

The classification of wastes regarding hazardous property HP 14 (ecotoxicity) is essential for proper waste management. In the EU, HP 14 has been estimated based on waste chemical composition rather than using biotests, and guidelines for experimental assessment are still lacking. This study aims at evaluating the potential ecotoxicological impacts of weathered coal fly ash (CFA) from a landfill, as a case study to assess the current EU methodology used to classify wastes regarding HP 14. A large amount of CFA is still landfilled, but its valorisation would be of interest. The analysis was based on the chemical composition of CFA (in ClassifyMyWaste software), and on a battery of five biotests applied to eluates, with Lepidium sativum, Aliivibrio fischeri, Raphidocelis subcapitata, Lemna minor and Daphnia magna. Through chemical analysis, most of the simulations with data from the literature indicated "Possible Hazard", including the sample of this work. Biotests revealed low impairment for most endpoints. D. magna was the most sensitive organism, but the inhibitory effect was significantly reduced after pH adjustment of the eluate. The test with A. fischeri does not seem to be adequate to assess CFA due to the high variability observed in results. The methodology involving a simple battery of bioassays was proven to be enlightening, providing relevant results for HP 14 assessment. The chosen battery of biotests (excluding the A. fischeri test) may be a good starting point to represent the aquatic environment in this context. In short, it seems that weathered CFA can be considered non-hazardous, and therefore the material under analysis could be valorised in practical applications without significant ecotoxic effect on the environment.