Extraction, recovery and characterization of structural extracellular polymeric substances from anammox granular sludge

A novel strategy for waste activated sludge treatment: Recovery of structural extracellular polymeric substances and fermentative production of volatile fatty acids

Structural extracellular polymeric substances (SEPS) as valuable biopolymers, can be extracted from waste activated sludge (WAS). However, the extraction yield is typically low, and detailed information on SEPS characterizations, as well as proper treatment of the sludge after SEPS extraction, remains limited. This study aimed to optimize the conditions of heating-Na2CO3 extraction process to increase the yield of SEPS extracted from WAS. Subsequently, SEPS were characterized, and, for the first time, insights into their protein composition were uncovered by using proteomics. A maximum SEPS yield of 209 mg g-1 volatile solid (VS) was obtained under optimal conditions: temperature of 90 °C, heating time of 60 min, Na+ dosage of 8.0 mmol/g VS, and pH required to precipitation of 4.0, which was comparable to that from the aerobic granular sludge reported in literature. Proteomics analysis unveiled that the proteins in SEPS primarily originated from microorganisms involved in nitrogen fixation and organic matter degradation, including their intracellular and membrane-associated regions. These proteins exhibited various catalytic activities and played crucial roles in aggregation processes. Besides, the process of SEPS extraction significantly enhanced volatile fatty acid (VFA) production during the anaerobic fermentation of residual WAS after SEPS extraction. A maximum VFA yield of 420 ± 14 mg COD/g VSadded was observed in anaerobic fermentation of 10 d, which was 77.2 ± 0.1 % higher than that from raw sludge. Mechanism analysis revealed that SEPS extraction not only improved WAS disintegration and solubilization but also reduced the relative activity of methanogens during anaerobic fermentation. Moreover, SEPS extraction shifted the microbial population during anaerobic fermentation in the direction towards hydrolysis and acidification such as Fermentimonas sp. and Soehngenia sp. This study proposed a novel strategy based on SEPS extraction and VFA production for sludge treatment, offering potential benefits for resource recovery and improved process efficiency.

Integrating enhanced biological phosphorus removal in adsorption-stage to treat real domestic sewage

Wastewater treatment innovation toward resource recovery facilities raises concerns about the adsorption and bio-degradation (A-B) process. This study integrated enhanced biological phosphorus removal (EBPR) into the A-stage for real domestic sewage treatment using the short sludge retention time (S-SRT) approach. The S-SRT approach resulted in outstanding phosphorus (over 90 %) and COD removal (approximately 88 %), increased sludge yield and organic matter content, and a 1.68-fold increase in energy recovery efficiency by sludge anaerobic digestion. The inhibition of nitrification relieved competition for carbon sources between denitrification and phosphorus removal, allowing for the enrichment of phosphorus-accumulating organisms (PAOs) such as Tetrasphaera and Halomonas, leading to enhanced phosphorus removal activities. Biological adsorption also plays a significant role in achieving steady phosphorus removal performance. This study demonstrates the potential of the S-SRT approach as an effective strategy for simultaneous carbon and phosphorus capture in the A-stage, contributing to energy and nutrient recovery from sewage.

Rethinking characterization, application, and importance of extracellular polymeric substances in water technologies

Biofilms play important roles in water technologies such as membrane treatments and activated sludge. The extracellular polymeric substances (EPS) are key components of biofilms. However, the precise nature of these substances and how they influence biofilm formation and behavior remain critical knowledge gaps. EPS are produced by many different microorganisms and span multiple biopolymer classes, which each require distinct strategies for characterization. The biopolymers additionally associate with each other to form insoluble complexes. Here, we explore recent progress toward resolving the structures and functions of EPS, where a shift towards direct functional assessments and advanced characterization techniques is necessary. This will enable integration with better microbial community and omics analyses to understand EPS biosynthesis pathways and create further opportunities for EPS control and valorization.

Microbial extracellular polymeric substances in the environment, technology and medicine

Microbial biofilms exhibit a self-produced matrix of extracellular polymeric substances (EPS), including polysaccharides, proteins, extracellular DNA and lipids. EPS promote interactions of the biofilm with other cells and sorption of organics, metals and chemical pollutants, and they facilitate cell adhesion at interfaces and ensure matrix cohesion. EPS have roles in various natural environments, such as soils, sediments and marine habitats. In addition, EPS are relevant in technical environments, such as wastewater and drinking water treatment facilities, and water distribution systems, and they contribute to biofouling and microbially influenced corrosion. In medicine, EPS protect pathogens within the biofilm against the host immune system and antimicrobials, and emerging evidence suggests that EPS can represent potential virulence factors. By contrast, EPS yield a wide range of valuable products that include their role in self-repairing concrete. In this Review, we aim to explore EPS as a functional unit of biofilms in the environment, in technology and in medicine.

External redox couple enhanced anammox sludge activity at low temperature: Insight into intracellular resource synthesis

Anaerobic ammonium oxidation (anammox), an energy-efficient deamination biotechnology, faces operational challenges in low-temperature environments. Enhancing the metabolic activity of anammox bacteria (AnAOB) is pivotal for advancing its application in mainstream municipal wastewater treatment. Inspired by the metabolic adaptability of AnAOB and based on our previous findings, this work investigated the enhancement of intracellular ATP and NADH synthesis through the exogenous supply of reduced humic acid (HAred) and H2O2 redox couple, aiming to augment AnAOB activity under low-temperature conditions. Our experimental setup involved continuous dosing of 0.0067 μmol g-1 volatile suspended solid of H2O2 and 10 mg g-1 volatile suspended solid of HAred into a mainstream anammox reactor operated at 15 °C with an influent TN content of 60 mg/L. The results showed that HAred / H2O2 couple succeeded in maintaining the effluent TN at 10.72 ± 0.91 mg l-1. The specific anammox activity, ATP and NADH synthesis levels of sludge increased by 1.34, 2.33 and 6.50 folds, respectively, over the control setup devoid of the redox couple. High-throughput sequencing analysis revealed that the relative abundance of Candidatus Kuenenia after adding HAred / H2O2 couple reached 3.65 % at the end of operation, which was 5.14 folds higher than that of the control group. Further metabolomics analysis underscored an activation in the metabolism of amino acids, nucleotides, and phospholipids, which collectively enhanced the availability of ATP and NADH for the respiratory processes. These findings may provide guidance on strategy development for improving the electron transfer efficiency of AnAOB and underscore the potential of using redox couples to promote the mainstream application of anammox technology.

Aerobic and anoxic utilization of organic matter for flexible nitrite supply in nutrient conversion pathways based on anaerobic ammonium oxidation: Microbial interactive mechanism

This study investigated nutrient conversion pathways and corresponding interactive mechanisms in a mainstream partial-nitritation (PN)/anaerobic ammonium oxidation (anammox)/partial-denitrification-(PD)-enhanced biological phosphorus-removal (EBPR) (PN/A/PD-EBPR) process. A laboratory-scale sequencing batch reactor was operated for 301 days under different operational strategies. Mainstream PN/A/PD-EBPR was successfully operated with aerobic and anoxic utilization of organic matter. Aerobic utilization of organic matter was an effective strategy for conversion to denitrifying polyphosphate-accumulating organism-based phosphorus removal, referring to a biological reaction that outperformed nitrite-oxidizing bacteria. Aerobically adsorbed organic matter could be used as a carbon source for PD, which further enhanced nitrogen removal by PN/A. Ultimately, the interaction between complex nutrient conversion pathways served to achieve stable performance. High-throughput sequencing results elucidated the core microbe functioning in the mainstream PN/A/PD-EBPR process with respect to various nutrients. The outcomes of this study will be beneficial to those attempting to implement mainstream PN/A/PD-EBPR.

Coupling extracellular glycan composition with metagenomic data in papermill and brewery anaerobic granular sludges

Glycans are crucial for the structure and function of anaerobic granular sludge in wastewater treatment. Yet, there is limited knowledge regarding the microorganisms and biosynthesis pathways responsible for glycan production. In this study, we analysed samples from anaerobic granular sludges treating papermill and brewery wastewater, examining glycans composition and using metagenome-assembled genomes (MAGs) to explore potential biochemical pathways associated with their production. Uronic acids were the predominant constituents of the glycans in extracellular polymeric substances (EPS) produced by the anaerobic granular sludges, comprising up to 60 % of the total polysaccharide content. MAGs affiliated with Anaerolineacae, Methanobacteriaceae and Methanosaetaceae represented the majority of the microbial community (30-50 % of total reads per MAG). Based on the analysis of MAGs, it appears that Anaerolinea sp. and members of the Methanobacteria class are involved in the production of exopolysaccharides within the analysed granular sludges. These findings shed light on the functional roles of microorganisms in glycan production in industrial anaerobic wastewater treatment systems.

Effect of food-to-microorganisms ratio on aerobic granular sludge settleability: Microbial community, potential roles and sequential responses of extracellular proteins and polysaccharides

The food-to-microorganism ratio (F/M) is an important parameter in wastewater biotreatment that significantly affects the granulation and settleability of aerobic granular sludge (AGS). Hence, understanding the long-term effects and internal mechanisms of F/M on AGS settling performance is essential. This study investigated the relationship between F/M and the sludge volume index (SVI) within a range of 0.23-2.50 kgCOD/(kgMLVSS·d). Thiothrix and Candidatus_Competibacter were identified as two dominant bacterial genera influencing AGS settling performance. With F/M increased from 0.27 kgCOD/(kgMLVSS·d) to 1.53 kgCOD/(kgMLVSS·d), the abundance of Thiothrix significantly increased from 0.20% to 27.02%, and the hydrophobicity of extracellular proteins (PN) decreased, which collectively reduced AGS settling performance. However, under high-F/M conditions, the gel-like polysaccharides (PS) effectively retained the granular biomass by binding to the highly abundant Thiothrix (53.65%). The progressive increment in biomass led to a concomitant reduction in F/M, resulting in the recovery of AGS settleability. In addition, two-dimensional correlation infrared spectroscopy analysis revealed the preferential responses of PN and PS to the increase and decrease of F/M, and the content and characteristics of PN and PS played important roles in granular settling. The study provides insight into the microbial composition and the potential role of extracellular polymer substances in the AGS sedimentation behavior, offering valuable theoretical support for stable AGS operation.

Research progress on the role of biofilm in heavy metals adsorption-desorption characteristics of microplastics: A review

Microplastics (MPs) have been found to be widely distributed in aquatic environments, where they will interact with toxic heavy metals and result in more serious adverse effects on the aquatic environments and organisms. However, after entering the aquatic environments, MPs are quickly covered by biofilms, which significantly modify MPs properties and relevant heavy metals adsorption-desorption characteristics In order to better understand the adsorption behavior of heavy metals on biofilm developed MPs (BMPs), we comprehensively reviewed representative studies in this area. First, we summarized the formation process of biofilms on MPs. Subsequently, we reviewed the current understanding on the influence of biofilm formation on the properties of MPs and discussed the metal adsorption-desorption characteristics of MPs affected by these changes. Finally, based on the systematic literature review, some future research needs and strategies were proposed to further understand the interactions between MPs and heavy metals.

Granule formation mechanism, key influencing factors, and resource recycling in aerobic granular sludge (AGS) wastewater treatment: A review

The high-efficiency and additionally economic benefits generated from aerobic granular sludge (AGS) wastewater treatment have led to its increasing popularity among academics and industrial players. The AGS process can recycle high value-added biomaterials including extracellular polymeric substances (EPS), sodium alginate-like external polymer (ALE), polyhydroxyfatty acid (PHA), and phosphorus (P), etc., which can serve various fields including agriculture, construction, and chemical while removing pollutants from wastewaters. The effects of various key operation parameters on formation and structural stability of AGS are comprehensively summarized. The degradable metabolism of typical pollutants and corresponding microbial diversity and succession in the AGS wastewater treatment system are also discussed, especially with a focus on emerging contaminants removal. In addition, recent attempts for potentially effective production of high value-added biomaterials from AGS are proposed, particularly concerning improving the yield, quality, and application of these biomaterials. This review aims to provide a reference for in-depth research on the AGS process, suggesting a new alternative for wastewater treatment recycling.

Biological carbon promotes the recovery of anammox granular sludge after starvation

This article adopts the strategy of adding biochar and increasing HRT to accelerate the performance and particle morphology recovery of anaerobic ammonia oxidation granular sludge stored at room temperature for 68 days. The results showed that biochar accelerated the death of heterotrophic bacteria, shortened the cell lysis and lag period of the recovery process by 4 days, and it only took 28 days for the nitrogen removal performance of the reactor to recover to the original level, and 56 days for re-granulation. Biochar promoted the secretion of EPS (56.96 mg gVSS^-1), and the sludge volume and nitrogen removal performance of the bioreactor remain stable. Biochar also accelerated the growth of Anammox bacteria. The abundance of Anammox bacteria in the biochar reactor reached 38.76% on the 28th day. The high abundance of functional bacteria and the optimized community structure of biochar made system (Candidatus_Kuenenia: 38.30%) more risk-resistant than control reactor.

Celebrating 50 years of microbial granulation technologies: From canonical wastewater management to bio-product recovery

Microbial granulation technologies (MGT) in wastewater management are widely practised for more than fifty years. MGT can be considered a fine example of human innovativeness-driven nature wherein the manmade forces applied during operational controls in the biological process of wastewater treatment drive the microbial communities to modify their biofilms into granules. Mankind, over the past half a century, has been refining the knowledge of triggering biofilm into granules with some definite success. This review captures the journey of MGT from inception to maturation providing meaningful insights into the process development of MGT-based wastewater management. The full-scale application of MGT-based wastewater management is discussed with an understanding of functional microbial interactions within the granule. The molecular mechanism of granulation through the secretion of extracellular polymeric substances (EPS) and signal molecules is also highlighted in detail. The recent research interest in the recovery of useful bioproducts from the granular EPS is also emphasized.

Integrated resource recovery from aerobic granular sludge plants

The study evaluated the combined phosphorus, nitrogen, methane, and extracellular polymeric substances (EPS) recovery from aerobic granular sludge (AGS) wastewater treatment plants. About 30% of sludge organics are recovered as EPS and 25-30% as methane (≈260 ml methane/g VS) by integrating alkaline anaerobic digestion (AD). It was shown that 20% of excess sludge total phosphorus (TP) ends in the EPS. Further, 20-30% ends in an acidic liquid waste stream (≈600 mg PO₄-P/L), and 15% in the AD centrate (≈800 mg PO₄-P/L) as ortho-phosphates in both streams and is recoverable via chemical precipitation. 30% of sludge total nitrogen (TN) is recovered as organic nitrogen in the EPS. Ammonium recovery from the alkaline high-temperature liquid stream is attractive, but it is not feasible for existing large-scale technologies because of low ammonium concentration. However, ammonium concentration in the AD centrate was calculated to be 2600 mg NH₄-N/L and ≈20% of TN, making it feasible for recovery. The methodology used in this study consisted of three main steps. The first step was to develop a laboratory protocol mimicking demonstration-scale EPS extraction conditions. The second step was to establish mass balances over the EPS extraction process on laboratory and demonstration scales within a full-scale AGS WWTP. Finally, the feasibility of resource recovery was evaluated based on concentrations, loads, and integration of existing technologies for resource recovery.

Potential causes of partial-denitrification (PD) granular sludge breakdown under high nitrate loading rates

The granule instability has been frequently reported during the operation of high loading rates. While, there no research was performed on the recently developed anoxic partial-denitrification (PD) granules, a novel pathway in producing nitrite from nitrate for anammox process. Herein, this work, for the first time, investigated the influence of nitrate loading rates on the instability of PD granules and identified the key causes. Two lab-scale sequencing batch reactors (SBRs) were operated with nitrate loading rates (NLR) increased from 0.48 to 3.84 kg N/m³/d (R1, 8 cycles/d), and 0.96 to 7.68 kg N/m³/d (R2, 16 cycles/d) by gradually elevating the influent nitrate concentration. Results showed that nitrite production rates increased with the NLRs, with a maximal value of 5.26 kg N/m³/d obtained. However, the compact regular PD granules were not stable and broke down when NLR was above 3.84 kg N/m³/d, which resulted in serious sludge washing out from SBR. The high NLRs led to the extracellular polymeric substances (EPS) transformation in terms of its composition and structure, which the protein content in the EPS and the tightly bound EPS (T-EPS) fraction was significantly decreased, this was supposed to be the major reason causing the breakdown of PD granules. Besides, it was found the PD granule in R2 was more deteriorated than that in R1 under the same high NLR, suggesting the short starvation (idle) times in SBR cycle was likely another reason impairing the stability of PD granules. Overall, this research provides useful information in development of granule-based PD systems and sheds light on achieving high-rate nitrite production in SBR with great stability.

Improving mechanical stability of anammox granules with organic stress by limited filamentous bulking

Under organic stress, the limited filamentous bulking (FB) was demonstrated to improve anammox capability by inhibiting granule disintegration and washout. The accumulation of internal stress played a more important role than the adverse physicochemical properties (low viscoelasticity and hydrophobicity) of granules in limiting granular strength by consuming the granular elastic energy. Different from the floc-forming heterotrophic bacteria (HB) that stored its growth stress as internal stress by pushing the surrounded anammox micro-colonies outwards under the spatial constraint of elastic anammox "shell", the filamentous HB grew into a uniform network structure within granules, endowed granules low internal stress and acted as the granular skeleton due to its rich amyloid substance, which was benefited from the elimination of inhomogeneous growth and the consequent expansion competition for living space. Combined with the mechanical instability and sticking-spring models, controlling FB at limited level was effective for improving granular strength without affecting sludge-water separation.

Recovery of structural extracellular polymeric substances (sEPS) from aerobic granular sludge: Insights on biopolymers characterization and hydrogel properties for potential applications

Nowadays, wastewater treatment plants (WWTPs) are transforming into water resource recovery facilities (WRRFs) where the resource recovery from waste streams is pivotal. Aerobic granular sludge (AGS) is a novel technology applied for wastewater treatment. Extracellular polymeric substances (EPS) secreted by microorganisms promote the aggregation of bacterial cells into AGS and the structural fraction of EPS (sEPS) is responsible for the mechanical properties of AGS. sEPS can be extracted and recovered from waste AGS by physico-chemical methods and its characterization is to date of relevant concern to understand the properties in the perspective of potential applications. This study reports on: characterization of sEPS extracted and recovered from AGS; - formation and characterization of sEPS-based hydrogels. Briefly, sEPS were extracted by a thermo-alkaline process followed by an acidic precipitation. sEPS-based hydrogels were formed by a cross-linking process with a 2.5% w/w CaCl₂ solution. The following key-findings can be drawn: i) hydrogels can be formed starting from 1% w/w sEPS on, by diffusion of Ca²⁺ into sEPS network; ii) the Ca/C molar ratio of hydrogels decreased with increasing concentration of sEPS from 1 to 10% w/w; iii) the thermogravimetric and spectroscopic behaviours of sEPS show that the cross-linking reaction mainly involves the polysaccharidic fraction of biopolymers; iv) water-holding capacity up to 99 gH₂O/g_sEPS was registered for 1% w/w sEPS-based hydrogels, suggesting applications in several industrial sectors (i.e. chemical, paper, textile, agronomic, etc.); v) rheological results highlighted a solid-like behaviour (G'≫G") of sEPS-based hydrogels. The power-law fitting of G' vs. sEPS concentration suggests that the expansion of the sEPS network during cross-linking occurs through a percolative mechanism involving the initial formation of sEPS oligomers clusters followed by their interconnection towards the formation of 3D network. These findings provide additional information about the mechanisms of sEPS-based hydrogel formation and reveal the peculiar physico-chemical characteristics of sEPS which nowadays are increasingly gaining interest in the context of resource recovery.

Deciphering the spatial distribution along the upflow anammox reactor: Sludge characteristics and interspecies interactions

Here, nitrogen conversion, granular characteristics and microbial dynamics were combined to reveal the longitudinal heterogeneity along anammox-UASB with nitrogen removal efficiency of 92.6%. The reactor was divided into Bottom-zone, Middle-zone, Upper-zone, and Top-zone with height increasing. Results indicated that particle size decreased from Bottom-zone to Upper-zone, while granular floatation caused an increase in Top-zone. Protein secondary structure in EPS was loose and hzsA transcription ratio was only 4.45% due to the limited mass-transfer and serious mineralization of ultra-large granules in Bottom-zone. Smaller granules in Middle-zone were more robust and active, with compact tryptophan- and aromatic-like protein in EPS and 23.71% hzsA transcription. Intriguingly, coexisting denitrification survived on EPS and/or microbial metabolites was observed. Transcription of narG was stimulated with height increasing, resulted in performance improvement through combining partial denitrification and anammox in Upper-zone. The findings deciphered stratification characteristics along the height-partitioned anammox-UASB, and reveal cross-feedings between denitrification and anammox bacteria.

Correlation of structural extracellular polymeric substances in the mesh biofilms with solids retention time and biofilm hydraulic resistance in dynamic membrane bioreactors

Dynamic membrane bioreactor (DMBR), which mainly relied on the in-situ formed biofilms on support materials with large aperture (e.g., nylon mesh) to separate fine particles in wastewater, has attracted a lot of attentions due to low cost. The filtration performance of DMBR is mainly determined by the structure and hydraulic resistance of biofilms formed on the mesh. Therefore, understanding the correlation of operation conditions with mesh biofilm compositions and permeability are critically important for optimizing DMBR operation. In present study, how structural extracellular polymeric substances, including alginate-like extracellular polysaccharide (ALE) and amyloid-like protein (AP), in mesh biofilms correlate to solids retention time (SRT) and biofilm structures was explored in DMBRs. At 5d-SRT, compact and gel-like mesh biofilms were formed with a high specific filtration resistance (SFR) of 459 × 10⁹ m/g, while at 40d-SRT porous mesh biofilms were developed with a low SFR of 24 × 10⁹ m/g. Consequently, the 5d-SRT MBR experienced more rapid rise in transmembrane pressure. Further studies found that the 5d-SRT mesh biofilms had a higher AP content, which was positively correlated to biofilm hydraulic resistance. On the contrary, the 40d-SRT mesh biofilms contained a higher content of ALE, suggesting that ALE was negatively correlated to biofilm hydraulic resistance. Therefore, AP instead of ALE likely played a more important role in the formation of compact and gel-like mesh biofilms.

Effect of temperature on the compositions of ladderane lipids in globally surveyed anammox populations

The adaptation of bacteria involved in anaerobic ammonium oxidation (anammox) to low temperatures will enable more efficient removal of nitrogen from sewage across seasons. At lower temperatures, bacteria typically tune the synthesis of their membrane lipids to promote membrane fluidity. However, such adaptation of anammox bacteria lipids, including unique ladderane phospholipids and especially shorter ladderanes with absent phosphatidyl headgroup, is yet to be described in detail. We investigated the membrane lipids composition (UPLC-HRMS/MS) and dominant anammox populations (16S rRNA gene amplicon sequencing, Fluorescence in situ hybridization) in 14 anammox enrichments cultivated at 10-37 °C. "Candidatus Brocadia" appeared to be the dominant organism in all but two laboratory enrichments of "Ca. Scalindua" and "Ca. Kuenenia". At lower temperatures, the membranes of all anammox populations were composed of shorter [5]-ladderane ester (reduced chain length demonstrated by decreased fraction of C20/(C18 + C20)). This confirmed the previous preliminary evidence on the prominent role of this ladderane fatty acid in low-temperature adaptation. "Ca. Scalindua" and "Ca. Kuenenia" had distinct profile of ladderane lipids compared to "Ca. Brocadia" biomasses with potential implications for adaptability to low temperatures. "Ca. Brocadia" membranes contained a much lower amount of C18 [5]-ladderane esters than reported in the literature for "Ca. Scalindua" at similar temperature and measured here, suggesting that this could be one of the reasons for the dominance of "Ca. Scalindua" in cold marine environments. Furthermore, we propose additional and yet unreported mechanisms for low-temperature adaptation of anammox bacteria, one of which involves ladderanes with absent phosphatidyl headgroup. In sum, we deepen the understanding of cold anammox physiology by providing for the first time a consistent comparison of anammox-based communities across multiple environments.

Multiple roles of complex organics in polishing THP-AD filtrate with double-line anammox: Inhibitory relief and bacterial selection

Anammox process has been widely regarded as an energy-efficient method for sludge digestion filtrate treatment. However, the complex high-strength organics in the filtrate, especially of Anaerobic Digestion after Thermal Hydrolysis Pretreatment (THP-AD), brings serious threat to anammox bacteria, and the high nitrate residue in effluent remains another significant barrier in operation. In this study, a novel double-line anammox-mediated system, integrating the Partial Nitrification/Anammox (PNA) with Partial Denitrification/Anammox (PDA) processes in separately sequencing batch reactors (SBRs), was developed to polish the THP-AD filtrate. When the real THP-AD filtrate (1946.5 mg NH4+-N/L, 2076.0 mg COD/L) was fed to the front PNA reactor (SBRPNA) with 5-fold dilution, effluent total nitrogen (TN) remained at 93.0 mg/L. Notably, the final effluent TN was effectively polished to as low as 8.8 mg/L by the following PDA reactor (SBRPDA), which was fed with the SBRPNA effluent and real domestic wastewater (71.0 mg NH4+-N/L, 209.1 mg COD/L). More severe inhibition on anammox activity was observed in SBRPNA rather than SBRPDA by refractory organics in filtrate. Fortunately, it could be alleviated with the enhanced degradability of particulate organics and aromatic protein-like compounds, attributed to the enrichment of class Anaerolineae in both SBRPNA and SBRPDA. This further stimulated the electron donor supply for PDA process with much lower external carbon source demand. 16S rRNA sequencing analysis revealed that Candidatus Brocadia as dominant anammox bacteria were efficiently enriched in both SBRPNA and SBRPDA, indicating its unexpected toughness and adaptability to the complex organic compounds in THP-AD filtrate. Overall, this study suggested that the novel double-line anammox would be a promising alternative for cost-efficient nitrogen removal from high-strength wastewater containing complex organic matter.

A novel strategy for rapid development of a self-sustaining symbiotic algal-bacterial granular sludge: Applying algal-mycelial pellets as nuclei

Algal-bacterial granular sludge (ABGS) is a promising technology for wastewater treatment, benefiting from the synergetic interactions between algae and bacteria. However, the rapid start-up of the ABGS system is not trivial. Herein, a novel strategy was proposed by applying the algal-mycelial pellets (AMPs) as the primary nuclei for accelerating the development of a self-sustaining symbiotic ABGS system. The results indicated that by using this strategy complete granulation was shortened to 12 days, much shorter than the control system without AMPs dosage (28 days). The ABGS had a large particle diameter (3.3 mm), compact granular structure (1.0253 g/mL), and excellent settleability (SVI30 of 53.2 mL/g). Moreover, 98.6% of COD, 80.8% of TN and 80.0% of PO43--P were removed by the ABGS. The nuclei of targeted algae (Chlorella) and filamentous fungi (Aspergillus niger), the enhanced production of extracellular polymeric substances (especially proteins) and the enrichment of functional bacteria (such as Neomegalonema and Flavobacterium) facilitated the granules development. The low surface free energy (-69.56 mJ/m2) and energy barrier (89.93 KT) were the inherent mechanisms for the strong surface hydrophobicity, the easy bacterial adhesion, and the short granulation period. This study provides an economically feasible approach to accelerate ABGS granulation and sustain system stability.

Physicochemical methods for biofilm removal allow for control of biofilm retention time in a high rate MBBR

Controlling biofilm retention time in moving bed biofilm reactor (MBBR) and maintaining its performance for A-stage carbon redirection requires a reliable method to use as side stream biocarriers treatment. This paper investigates biofilm detachment and residual biofilm activity under multiple physicochemical treatment scenarios aiming to provide an applicable technique for control of biofilm retention time. Different mixing intensities (i.e. 30-120 rpm), filling fractions (i.e. 20%-100%), and pH (i.e. 2-12) were evaluated. Two continuously operating MBBRs were subjected to pH shocks of 2 and 12 to evaluate the impact of residual acidic or alkaline compounds on performance. The highest solids detachment (i.e. 70 ± 5%) was found in alkaline conditions and independent of mixing intensity and filling fraction. Biofilm detachment test revealed that alkaline shock produced higher detachment levels in a longer exposure time when compared to acidic conditions. The kinetic tests revealed 60% and 90% of the residual biofilm activity was lost at pH 12 and 2. The continuously operating MBBRs subjected to pH shocks of 2 and 12 demonstrated a 50% loss of soluble COD removal capability within one hydraulic retention time. Extracellular polymeric substances changes in its structure and surface properties influencing the degree of biofilm detachment and its solubilization properties leading to differences in biofilm resilience. The findings have shown that by applying a side stream alkali treatment it could be possible to control biofilm retention time ensuring its detachment up to 70% and a reduced impact on the residual biofilm activity returning to the reactor.

Performance and bacterial community profiles of sequencing batch reactors during long-term exposure to polyethylene terephthalate and polyethylene microplastics

Microplastics (MPs) are ubiquitous in wastewater treatment plants (WWTPs), but much remains to be learned about their roles in WWTPs. Herein, polyethylene terephthalate (PET) and polyethylene (PE) particles were added into sequencing batch reactors (SBRs), and the sole impacts and co-impacts of MPs with other pollutants (phenol and Cu²⁺) on wastewater treatment processes were evaluated. Results indicated that MPs did not significantly affect SBR performance, either alone or co-occurrence with phenol, but the co-exposure to MPs and Cu²⁺ severely suppressed COD removal efficiency by 37.02%-64.70%. The functional groups of activated sludge had no changes after receiving MPs, but the MPs-Cu²⁺ co-exposure could greatly promote the secretion of extracellular polymeric substances. Furthermore, MPs had no negative impacts on diversity, richness and structure of bacterial communities, and PET and PE showed different preferences for enrichment of bacterial populations. Moreover, the MPs-Cu²⁺ co-exposure obviously reduced the overall abundances of Cu-related genes in SBRs.

Heavy metal biosorption by Extracellular Polymeric Substances (EPS) recovered from anammox granular sludge

The recovery and conversion of Extracellular Polymeric Substances (EPS) from sewage sludge into bio-based commodities might improve the economics and environmental sustainability of wastewater treatment. This contribution explores the application of EPS from anammox granular waste sludge as biosorbent for the removal of heavy metals, specifically lead, copper, nickel, and zinc. Adsorption capacities equivalent or higher than well-established adsorbent media emerged from single-metal biosorption studies (up to 84.9, 52.8, 21.7 and 7.4 mg/gTS_EPS for Pb²⁺, Cu²⁺, Ni²⁺ and Zn²⁺, respectively). Combining spectroscopic techniques, a mechanistic hypothesis for metal biosorption, based on a combination of electrostatic interaction, ion exchange, complexation, and precipitation, was proposed. The adsorption mechanisms of extracted EPS and non-extracted EPS in the native biomass were indirectly compared by means of single-metal biosorption studies performed with pristine granules (adsorbing up to 103.7, 36.1, 48.2 and 49.8 mg/gTSgranules of Pb²⁺, Cu²⁺, Ni²⁺, and Zn²⁺, respectively). In comparison with pristine anammox granules, EPS showed lower adsorption capacities except for copper and different adsorption pathways as postulated based on the adsorption data interpretation via theoretical models. The multi-metal biosorption tests excluded significant competitions among different heavy metals for the EPS binding sites, thus opening further scenarios for the treatment of complex wastewaters.

Insight into correlation of advanced nitrogen removal with extracellular polymeric substances characterization in a step-feed three-stage integrated anoxic/oxic biofilter system

As a core component of the biomass, the important role of extracellular polymeric substances (EPS) on treatment performance has been recognized. However, the comprehensive understanding of its correlation with nitrogen removal remains limited in biofilm-based reactors. In this study, the relevance between EPS and advanced nitrogen removal in a novel step-feed three-stage integrated anoxic/oxic biofilter (SFTIAOB) was specifically investigated. The operation showed as high as 81% TN removal was achieved under optimal conditions. Among the whole reactor, 2nd anoxic (A2) zone was the largest contributor for nitrogen removal, followed by the 3rd anoxic (A3) and 2nd oxic (O2) zones. EPS composition analysis found that high content of polysaccharides in tightly bound-EPS (A2 and A3) and protein in loosely bound-EPS and tightly bound-EPS (O2). Fourier transform infrared spectroscopy, three-dimensional fluorescence spectrum further verified stratified EPS subfractions containing different secondary protein structures, while 3-turn helix and tryptophan-like protein was the main reason for nitrogen removal. High-throughput sequencing revealed the co-existence of nitrogen removal-associated genera accomplished nitrification/denitrification combined with aerobic denitrification and anammox. Moreover, the correlation of EPS and microbial composition with nitrogen removal was clarified by redundancy analysis (RDA). Finally, potential mechanism for nitrogen removal was illuminated. This research gives more insight into EPS characteristics in enhancing nitrogen removal during the operation and optimization of a step-feed multi-stage A/O biofilm process.

Feasibility of partial-denitrification/ anammox for pharmaceutical wastewater treatment in a hybrid biofilm reactor

Biological nitrogen removal from pharmaceutical wastewater has drawn increasing attention due to biotoxicity and inhibition. In this study, for the first time, a novel approach integrating partial-denitrification with anaerobic ammonia oxidation (PD/A) in a sequencing biofilm batch reactor (SBBR) was proposed and demonstrated to be efficient to treat the bismuth nitrate and bismuth potassium citrate manufacturing wastewater, containing ammonia (NH₄⁺-N) and nitrate (NO₃^--N) of 6300±50 mg L ^- 1 and 15,300±50 mg L ^- 1. The maximum anammox activity was found at the shock effect of influent total nitrogen (TN) of 100 mg L ^- 1 with NO₃^--N/NH₄⁺-N of 1.0. Long-term operation demonstrated that the PD/A biofilm was developed rapidly after 30 days using synthetic influent, with TN removal efficiency increasing from 40.9% to 80.8%. Significantly, the key bacteria for PD/A had high tolerance and adapted rapidly to pharmaceutical wastewater, achieving a relatively stable TN removal efficiency of 81.2% with influent NH₄⁺-N and NO₃^--N was 77.9 ± 2.6 and 104.1 ± 4.4 mg L ^- 1 at a relatively low COD/NO₃^--N of 2.6. Anammox pathway contributed to TN removal reached 83.6%. Significant increase of loosely-bound extracellular polymeric substances was obtained with increasing protein of 3-turn helices structure as response to the inhibitory condition. High-throughput sequencing analysis revealed that the functional genus Thauera was highly enriched in both biofilms (9.5%→43.6%) and suspended biomass (15.5%→57.5%), which played a key role in high NO₂^--N accumulation. While the anammox bacteria decreasing from 7.8% to 1.6% in biofilm, and from 1.8% decreased to 0.1% in the suspended sludge. Overall, this study provides a new method of high-strength pharmaceutical wastewater treatment with low energy consumption and operation cost, as well as a satisfactory efficiency.

Comparison of recovery characteristics between AnAOB and AOB-AnAOB granular sludge after long-term storage

The recovery characteristics of long-term stored sludge are still elusive. Here, an AnAOB granular sludge reactor (R1) (15 d) was found to recover faster than AOB-AnAOB granular sludge reactor (R2) (21 d) after 240 d 4 °C storage. Higher nitrogen removal performance was also achieved in R1 (5.96 ± 0.14 kg N/(m³·d)) than that of R2 (0.33 ± 0.02 kg N/(m³·d)). It was indicated that more c-di-GMP synthetase was predicted in R1 triggered more amino acid metabolic function genes (Pyruvate kinase and 6-phosphofructokinase) which can secrete more extracellular proteins. Correspondingly, the higher abundance of functional genes related to exopolysaccharide secretion (Glucokinase and UDP-glucose 4-epimerase) trigger by GP6, GP10 and GP16 was found in R2. In addition, some heterotrophic bacteria cooperating with AnAOB (Comamonas and Simplicispira) were found more active in R1 than that of R2 due to the higher relative abundance of functional genes related to folic acid metabolic (Dihydrofolate synthase and Dihydrofolate reductase). However, AOB-AnAOB granular sludge was observed more likely to protect cells through NAD(P)-dependent dehydrogenase. It was indicated that AnAOB granular sludge has better application potential, more active characteristics of aggregation metabolism and collaboration with auxiliary bacteria than that of R2.

Wastewater Valorization: Practice around the World at Pilot- and Full-Scale

Over the last few years, wastewater treatment plants (WWTPs) have been rebranded as water resource recovery facilities (WRRFs), which recognize the resource recovery potential that exists in wastewater streams. WRRFs contribute to a circular economy by not only producing clean water but by recovering valuable resources such as nutrients, energy, and other bio-based materials. To this aim, huge efforts in technological progress have been made to valorize sewage and sewage sludge, transforming them into valuable resources. This review summarizes some of the widely used and effective strategies applied at pilot- and full-scale settings in order to valorize the wastewater treatment process. An overview of the different technologies applied in the water and sludge line is presented, covering a broad range of resources, i.e., water, biomass, energy, nutrients, volatile fatty acids (VFA), polyhydroxyalkanoates (PHA), and exopolymeric substances (EPS). Moreover, guidelines and regulations around the world related to water reuse and resource valorization are reviewed.

The differences in characteristics of extracellular polymeric substances of flocs and anammox granules impacted aggregation

Extracellular polymeric substances (EPS) are considered crucial components in the formation of microbial aggregates such as biofilms, flocs and granules. However, the role of EPS in sludge aggregation is still unclear. In this study, the differences in EPS characteristics of anammox granular sludge (AG), anammox floc sludge (AF) and activated floc sludge (AS) were investigated to clarify its role in granular aggregation. The results showed that the flocculation ability of EPS extracted from AG (62.8 ± 2.3%) was notably higher than that of EPS extracted from AF (35.7 ± 1.7%) and AS (17.3 ± 1.5%). The zeta potential and hydrophobicity of EPS showed the same tendency. In addition, the PN/PS ratio of AG, AF and AS were 7.66, 4.62 and 3.93, respectively. FTIR, XPS and 3D-EEM fluorescence spectra results revealed that anammox granular sludge has a higher ratio of hydrophobic groups, α-helixs/(β-sheets and random coils), intermolecular hydrogen bonds, and aromatic amino acids, and a lower ratio of electronegative groups. Anammox granular sludge exhibited high aggregation ability, because its EPS had higher zeta potential, hydrophobicity and intermolecular hydrogen bond ratio. This work provides a better understanding of the high aggregation ability of anammox granules and a theoretical basis for improving granules proportion and retention ability of microbes in reactor system.

Extracellular biopolymers recovered as raw biomaterials from waste granular sludge and potential applications: A critical review

Granular sludge (GS) is a special self-aggregation biofilm. Extracellular polymeric substances (EPS) are mainly associated with the architectural structure, rheological behaviour and functional stability of fine granules, given that their significance to the physicochemical features of the biomass catalysing the biological purification process. This review targets the EPS excretion from GS and introduces newly identified EPS components, EPS distribution in different granules, how to effectively extract and recover EPS from granules, key parameters affecting EPS production, and the potential applications of EPS-based biomaterials. GS-based EPS components are highly diverse and a series of new contents are highlighted. Due to high diversity, emerging extraction standards are proposed and recovery process is capturing particular attention. The major components of EPS are found to be polysaccharides and proteins, which manifest a larger diversity of relative abundance, structures, physical and chemical characteristics, leading to the possibility to sustainably recover raw materials. EPS-based biomaterials not only act as alternatives to synthetic polymers in several applications but also figure in innovative industrial/environmental applications, including gel-forming materials for paper industry, biosorbents, cement curing materials, and flame retardant materials. In the upcoming years, it is foreseen that productions of EPS-based biomaterials from renewable origins would make a significant contribution to the advancement of the circular economy.

Unraveling the capability of graphene nanosheets and γ-Fe2O3 nanoparticles to stimulate anammox granular sludge

In this study, we investigated the potentials of nanomaterials to enhance anaerobic ammonium oxidation (anammox) process, in terms of nitrogen removal, microbial enrichment, and activity of key enzymes. Graphene nanosheets (GNs) and γ-Fe₂O₃ nanoparticles (NPs) were selected due to their catalytic functions as conductive material and electron shuttles, respectively. The obtained results revealed that the optimum dosage of GNs (10 mg/L) boosted the nitrogen removal rate (NRR) by 46 ± 3.1% compared to the control, with maximum NH₄⁺-N and NO₂^--N removal of 86.5 ± 2.7% and 97.1 ± 0.5%, respectively. Moreover, hydrazine dehydrogenase (HDH) enzyme activity was augmented by 1.1-fold when using 10 mg/L GNs. The presence of GNs promoted the anammox granulation via enhancement of hydrophobic interaction of extracellular polymeric substances (EPS). Regarding the use of γ-Fe₂O₃ NPs, 100 mg/L dose increased NRR by 55 ± 3.8%; however, no contribution to HDH enzyme activity and a decrease in EPS compositions were observed. Given that the abiotic use of γ-Fe₂O₃ NPs further resulted in high adsorption efficiency (~92%), we conclude that the observed promotion due to γ-Fe₂O₃ NPs was mainly abiotic. Moreover, the 16S rRNA analysis revealed that the relative abundance of genus C. Jettenia (anammox related bacteria) increased from 11.9% to 12.3% when using 10 mg/L GNs, while declined to 8.3% at 100 mg/L γ-Fe₂O₃ NPs. Eventually, nanomaterials could stimulate the efficiency of anammox process, and this promotion and associated mechanism depend on their dose and composition.

Deammonification process in municipal wastewater treatment: Challenges and perspectives

The deammonification process has been proved to be an efficient nitrogen removal process in treating high NH₄⁺-N concentration wastewater (sidestream deammonification). It is very hopeful to bring WWTP close to energy autarky. However, the feasibility of applying mainstream deammonification to sewage treatment need to be further explored. Therefore, this review attempts to give an overview of challenges in applying mainstream deammonification and to discuss the impacts of unfavorable conditions on main functional species. In addition, some novel control strategies to maintain the dominant position of desired species were summarized. Efficient solution to the conflict between AnAOB (Anaerobic ammonium-oxidizing bacteria) biomass retention and NOB (Nitrite oxidizing bacteria) wash out was also reviewed. Ultimately, we suggested further studies including effective improved process that achieve combination of autotrophy and organotrophy species based on the metabolic diversity of AnAOB.

Anammox Granule Enlargement by Heterogenous Granule Self-assembly

Expansion in the size is an indispensable stage in the granular sludge life cycle, but little attention has been payed to the enlargement mechanism of granular sludge. Here, we propose a novel anammox granule enlargement mechanism by the self-assembly of heterogenous granules. Two different colors of anammox granules, dark-red granules (DR-Granules) and bright-red granules (BR-Granules) were found in an expanded granular sludge bed reactor. These two heterogenous granules were not isolated but were assembled into granules with a larger DR-Granule in the center and many smaller BR-Granules aggregated on the surface, increasing the overall granular size. Their physiochemical characteristics in terms of EPS, adherence, rheological properties, and microbial compositions, were identified and compared to elucidate the interaction between the different colors of granules. The BR-Granules created 92% more extracellular polymeric substances than the DR-Granules. This material blocked the passage of gas and substrate, leading to BR-Granules smaller size and a yield stress approximately 48% lower than that of the DR-Granules. Nevertheless, the BR-Granules had compact extracellular protein secondary structures and a high adherence rate to the surface of the DR-Granules, upon which they formed a compact adhered layer. These unique features enabled them to directionally adhere to DR-Granules in the core, that is, two heterogenous colors of granules self-assembled into large anammox granules. The enlargement mechanism was further supported by the abundance of K-strategy Ca. Kuenenia in the DR-Granules (inner layer) being higher than in the BR-Granules (outer layer; 2.9 ± 0.4% vs. 0.4 ± 0.1%; p = 0.0003) and by visualized confirmation that the larger BR-Granules wrapped around smaller DR-Granules inside. This demonstrates that heterogenous anammox granules actively self-assemble into large granules, which is an important step in the lifecycle of anammox granules.

Anammox process dosed with biochars for enhanced nitrogen removal: Role of surface functional groups

Biochar is an inexpensive redox-active carbon material that has been demonstrated to enhance microbial nitrogen-transforming processes. However, how redox-active biochar affects anammox remains unclear. Here, the effects of three functionally distinct biochars produced from corn stover biomass at varied pyrolysis temperatures (CS300, CS500, CS800) were evaluated as additives on the anammox performance in three reactors (R300, R550, R800) over the long term, during which nitrogen loading rate was either increased drastically (pulse strategy) or gradually (gradual strategy). Nitrogen removal was achieved at 86.5% (R300), 77.1% (Control), 59.3% (R550) and 57.7% (R800) under pulse strategy, and at 95.4% (R300), 92.3% (R550), 86.2% (Control) and 82.0% (R800) under gradual strategy, respectively. Compared with Control, addition of CS300 increased abundance of Candidatus Kuenenia with superior anammox activity. CS300 enriched with reduced functional groups (phenolic/hydroquinone) could donate electrons to support bioenergetics of anammox metabolism, whereas electron-accepting CS800 functioned inversely. Overall, this study highlights the importance of surface functional groups and redox property of biochar such that determines whether its addition impose stimulatory or suppressive effect on anammox process.

Importance of exopolysaccharide branched chains in determining the aggregation ability of anammox sludge

The high aggregation ability of anammox granular sludge is an issue of wide concern; however, the mechanism needs to be further clarified. In this study, selective hydrolysis experiments were performed to determine the role of exopolysaccharide (PS) branched chains and proteins for the aggregation mechanism of anammox granular sludge. The results revealed that selective hydrolysis of proteins hardly affected the granular aggregation while the hydrolysis of PS branched chains led to a decrease in the sludge zeta potential by 17.3% (β-amylase group) and 24.1% (isoamylase group), a decrease of hydrophobicity by 11.6% (β-amylase group) and 17.7% (isoamylase group), an increase of surface free energy by 36.8% (β-amylase group) and 55.1% (isoamylase group) and the deterioration of the PS self-assembly ability. In addition, FTIR and XPS spectra analysis showed that the disruption of PS branched chains resulted in a higher proportion of hydrophilic and electronegative groups, which hindered bacterial aggregation, which was further confirmed by XDLVO theory. The key role of the PS chain structure in sludge aggregation is a critical finding of this work that provides helpful insights for the application of anammox process.

Phase Transitions by an Abundant Protein in the Anammox Extracellular Matrix Mediate Cell-to-Cell Aggregation and Biofilm Formation

By employing biophysical and liquid-liquid phase separation concepts, this study revealed how a highly abundant extracellular protein enhances the key environmental and industrial bioprocess of anaerobic ammonium oxidation (anammox). Extracellular proteins of environmental biofilms are understudied and poorly annotated in public databases. Understanding the function of extracellular proteins is also increasingly important for improving bioprocesses and resource recovery. Here, protein functions were assessed based on theoretical predictions of intrinsically disordered domains, known to promote adhesion and liquid-liquid phase separation, and available surface layer protein properties. A model is thus proposed to explain how the protein promotes aggregation and biofilm formation by extracellular matrix remodeling and phase transitions. This work provides a strong foundation for functional investigations of extracellular proteins involved in biofilm development.

This study describes the first direct functional assignment of a highly abundant extracellular protein from a key environmental and biotechnological biofilm performing an anaerobic ammonium oxidation (anammox) process. Expression levels of Brosi_A1236, belonging to a class of proteins previously suggested to be cell surface associated, were in the top one percentile of all genes in the “Candidatus Brocadia sinica”-enriched biofilm. The Brosi_A1236 structure was computationally predicted to consist of immunoglobulin-like anti-parallel β-strands, and circular dichroism conducted on the isolated surface protein indicated that β-strands are the dominant higher-order structure. The isolated protein was stained positively by the β-sheet-specific stain thioflavin T, along with cell surface- and matrix-associated regions of the biofilm. The surface protein has a large unstructured content, including two highly disordered domains at its C terminus. The disordered domains bound to the substratum and thereby facilitated the adhesion of negatively charged latex microspheres, which were used as a proxy for cells. The disordered domains and isolated whole surface protein also underwent liquid-liquid phase separation to form liquid droplets in suspension. Liquid droplets of disordered protein wet the surfaces of microspheres and bacterial cells and facilitated their coalescence. Furthermore, the surface layer protein formed gels as well as ordered crystalline structures. These observations suggest that biophysical remodeling through phase transitions promotes aggregation and biofilm formation.

Biorefineries in circular bioeconomy: A comprehensive review

Biorefinery is a sustainable means of generating multiple bioenergy products from various biomass feedstocks through the incorporation of relevant conversion technologies. With the increased attention of circular economy in the past half-decade with the emphasis of holistically addressing economic, environmental, and social aspects of the industrial-sector, biorefinery acts as a strategic mechanism for the realization of a circular bioeconomy. This study presents a comprehensive review of different biorefinery models used for various biomass feedstocks such as lignocelluloses, algae, and numerous waste-types. The review focuses on how biorefinery is instrumental in the transition of various biomass-based industries in a circular bioeconomy. The results reveal that the social-economic aspect of the industrial sector has a major influence on the full adoption of biorefineries in circular bioeconomy. Biomass wastes have played a major role in the implementation of biorefinery in circular bioeconomy. The current challenges are also presented along with future perspectives.

Extracellular protein isolation from the matrix of anammox biofilm using ionic liquid extraction

Anaerobic ammonium oxidation (anammox)-performing bacteria self-assemble into compact biofilms by expressing extracellular polymeric substances (EPS). Anammox EPS are poorly characterized, largely due to their low solubility in typical aqueous solvents. Pronase digestion achieved 19.5 ± 0.9 and 41.4 ± 1.4% (w/w) more solubilization of laboratory enriched Candidatus Brocadia sinica anammox granules than DNase and amylase, respectively. Nuclear magnetic resonance profiling of the granules confirmed proteins as dominant biopolymer within the EPS. Ionic liquid (IL) 1-ethyl-3-methylimidazolium acetate and N,N-dimethylacetamide (EMIM-Ac/DMAc) mixture was applied to extract the major structural proteins. Further treatment by anion exchange chromatography isolated homologous serine (S)- and threonine (T)-rich proteins BROSI_A1236 and UZ01_01563, which were major components of the extracted proteins, and sequentially highly similar to putative anammox extracellular proteins KUSTD1514 and WP_070066018.1 of Ca. Kuenenia stuttgartiensis and Ca. Brocadia sapporoensis, respectively. Six monosaccharides (i.e., arabinose, xylose, rhamnose, fucose, galactose, and mannose) were enriched for BROSI_A1236 against all other major proteins. The sugars, however, contributed < 0.5% (w/w) of total granular biomass and were likely co-enriched as glycoprotein appendages. This study demonstrates that BROSI_A1236 is a major extracellular component of Ca. B. sinica anammox biofilms that is likely a common anammox extracellular polymer, and can be isolated from the matrix following ionic liquid extraction.

Performance and microbial community of the CANON process in a sequencing batch membrane bioreactor with elevated COD/N ratios

In this study, the effects of elevated chemical oxygen demand/nitrogen (COD/N) ratios on nitrogen removal, production and composition of the extracellular polymer substances (EPS) and microbial community of a completely autotrophic nitrogen removal via nitrite (CANON) process were studied in a sequencing batch membrane bioreactor (SBMBR). The whole experiment was divided into two stages: the CANON stage (without organic matter in influent) and the simultaneous partial nitrification, anaerobic ammonia oxidation and denitrification (SNAD) stage (with organic matter in influent). When the inflow ammonia nitrogen was 420 mg/L and the COD/N ratio was no higher than 0.8, the addition of COD was helpful to the CANON process; the total nitrogen removal efficiency (TNE) was improved from approximately 65% to more than 75%, and the nitrogen removal rate (NRR) was improved from approximately 0.255 kgN/(m³·d) to approximately 0.278 kgN/(m³•d), while the TNE decreased to 60%, and the NRR decreased to 0.236 kgN/(m³•d) when the COD/N ratio was elevated to 1.0. For the EPS, the amounts of soluble EPS (SEPS) and loosely bound EPS (LB-EPS) were both higher in the CANON stage than in the SNAD stage, while the amount of tightly bound EPS (TB-EPS) in the SNAD stage was significantly higher due to the proliferation of heterotrophic bacteria. The metagenome sequencing technique was used to analyse the microbial community in the SBMBR. The results showed that the addition of COD altered the structure of the bacterial community in the SBMBR. The amounts of Candidatus 'Anammoxoglobus' of anaerobic ammonia oxidation bacteria (AAOB) and Nitrosomonas of ammonia oxidizing bacteria (AOB) both decreased significantly, and Nitrospira of nitrite oxidizing bacteria (NOB) was always in the reactor, although the amount changed slightly. A proliferation of denitrifiers related to the genera of Thauera, Dokdonella and Azospira was found in the SBMBR.

Interactions between tetracycline and extracellular polymeric substances in anammox granular sludge

The effects of antibiotics on extracellular polymeric substances (EPS) using tetracycline as the model chemical were analyzed in terms of molecular property and structure. Results showed that three components, tryptophan, tryptophan type-proteins and polysaccharides in EPS of granular sludge from anaerobic ammonium oxidation (anammox) reactor can interacted with tetracycline, detected by the static quenching via the endogenous fluorescence quenching and transient fluorescence spectroscopy. Thermodynamic experiment confirmed that their interaction was dominated by the hydrophobic force. Combined with the synchronous fluorescence spectroscopy, it was found that tetracycline facilitated the extension degree of peptide chains in tryptophan type-proteins, leading to the enhancement of hydrodynamic diameter of the macromolecules in EPS when binding with tetracycline. EPS in AnGS demonstrated the resistance ability to tetracycline by converting from gel to sol state in rheological term. With the increase of tetracycline concentration, the stability of elastic structures in EPS declined, influencing the AnGS stability.

Hydrogels formed by anammox extracellular polymeric substances: structural and mechanical insights

The recovery of biopolymers from the waste sludge produced in wastewater treatments and their application in other industrial sectors, would substantially increase the environmental and economical sustainability of the process, promoting the development of a circular economy. In this study, extracellular polymeric substances (EPS) extracted from anammox granular waste sludge, were investigated and characterized. Rheological and differential scanning calorimetry measurements on EPS aqueous dispersions indicate the formation of an extended 3-D network above a threshold concentration, with a clear dependence of the mechanical and water retention properties on EPS content. The structural characterization, performed with transmission electron microscopy and small angle X-ray scattering, reveals the presence of functional amyloids as putative structural units, observed for the first time in an EPS-based hydrogel. As a proof of concept of the applicative potential, we explored the water and grease resistance provided to paper by an EPS coating. These results shed light on the structural details of EPS-based hydrogels, and pave the way for the possible use of EPS-based materials as a cheap, eco-friendly alternative to commonly adopted paper coatings, in line with a circular economy pattern for wastewater treatment.