Toward 3D graphene oxide gels based adsorbents for high-efficient water treatment via the promotion of biopolymers

Evaluation, optimization study, and life cycle assessment of novel eco-friendly PVA-based nanocomposite hydrogel adsorbents for methylene blue and paracetamol removal

In this study, an eco-friendly and novel hydrogel based on a crosslinked polyvinyl alcohol (PVA), iota carrageenan (IC) and polyvinylpyrrolidone (PVP) scaffold, containing a large amount (10-50 wt%) of nanoscale palm fronds (NPF) as additives, for water purification was demonstrated. A life cycle assessment (LCA) findings on NPF as biomass waste incorporated into PVA_PVP_IC polymer matrix was presented, and the results highlight the necessity of focused actions to reduce environmental impact and support the palm waste utilization in a sustainable manner. The multicomponent nanocomposite hydrogels were examined as adsorbents in a system work in batches for methylene blue (MB) and paracetamol (PCT) removal. The results show that, the presence of NPF, which dispersed in the hydrogel PVA_PVP_IC scaffolds containing both covalent and non-covalent cross-linking bonds, greatly enhanced the MB and PCT adsorption efficiency. A response surface methodology (RSM) model was used to find the best operating parameters of contaminant adsorption, including time, adsorbent dose, and starting concentration of pollutants. By using this statistical model, it was found that the optimal conditions for the adsorption reaction to achieve the complete removal of MB are 66.7 h adsorption time duration, 98.5 mg L-1 starting concentration, and an adsorbent dose of 5.9 mg, while for the complete removal of PCT, it is 57.6 h adsorption time duration, 80 mg L-1 starting concentration, and an adsorbent dose of 6 mg. The reusability of the nanocomposite hydrogels were tested for 5 cycles, all showed high adsorption capacity, indicating the potential for practical application of this nanocomposite hydrogel system. This study indicates that the prepared nanocomposite hydrogel raises the standard used for treatment of wastewater and also gives a solution to protect the environment and mitigate global warming.

Sodium alginate based adsorbent: Facile fabrication, extraordinary removal efficacy of anionic dyes and adsorption mechanism

Eco-friendly and renewable sodium alginate, as a potential alternative to fossil resources, has attracted considerable attention in wastewater treatment field. Herein, we develop a SA/PEI/PEG (sodium alginate/polyethyleneimine/polyethylene glycol diglycidyl ether) adsorbent in which SA was functionalized by PEI/PEG via a facile but effective strategy of one-pot gelation of aqueous SA/PEI/PEG solution. Systematic investigations were accomplished to explore the effects of adsorbent factors on the adsorption performances of the adsorbent towards the anionic dyes CR (congo red), AB-10B (amido black-10B), and AB-25 (acid blue-25). Strikingly, the SA/PEI/PEG exhibited exceptional adsorption performance to CR (2782 mg g-1, 90.6 %), AB-10B (1369 mg g-1, 90.9 %) and AB-25 (4221 mg g-1, 92.6 %) at 30 °C, pH = 3, 200 r min-1 and oscillated 24 h, and demonstrating exceptional reusability after six cycles of adsorption-desorption cycles. Furthermore, the three kinetic, four isothermic and one thermodynamic models were used to investigate the adsorption behaviors of the adsorbent towards these dyes. The possible adsorption mechanism is suggested: Hydrogen bond interactions and electrostatic attractions between SA/PEI/PEG and the dyes primarily contribute to exceptional adsorption capacity. The SA/PEI/PEG adsorbent endowed with easy fabrication, extraordinary adsorption capacity and excellent reusability promises potential application prospects in wastewater purification industry.

Construction of a novel ternary synergistic CuFe2O4-SnO2-rGO heterojunction for efficient removal of cyanide from contaminated water

Many industrial effluents release cyanide, a well-known hazardous and bio-recalcitrant pollutant, and thus, the treatment of cyanide wastewater is a major challenge. In the current study, a CuFe2O4-SnO2-rGO nanocomposite was synthesized to remove cyanide from an aqueous system. The structural and morphological characterizations of the nanomaterials were investigated by X-ray diffraction (XRD), Fourier transform infrared spectroscopy (FTIR), scanning electron microscopy (SEM) and energy dispersive spectra (EDX) analysis. The results revealed that almost 97.7% cyanide removal occurred using the nanocomposite at an initial concentration of 100 mg L-1 within 1 h. The experimental data were fitted to various adsorption models, among which the Langmuir model fitted the data very well, confirming the monolayer adsorption process. The kinetic investigation revealed that the cyanide adsorption process followed a pseudo-second-order kinetic model, indicating a chemisorption process with a high cyanide adsorption capacity of 114 mg g-1. The result of the intraparticulate diffusion model fitting revealed a decreasing slope value (K) from stage 1 to stage 2, indicating that external mass transfer is the predominating step. Moreover, the CuFe2O4-SnO2-rGO nanocomposite shows excellent reusability.

Thermo-chemical behaviour of Dunaliella salina biomass and valorising their biochar for naphthalene removal from aqueous rural environment

Thermo-chemical behavior of a microalgal biomass; Dunaliella salina was investigated through thermo-gravimetric analyses. Fully-grown D. salina biomass were subjected for biochar conversion using pyrolytic treatment at three distinct heating rates such as 2.5, 5, and 15 °C min-1. The kinetic appraisals were explained by using model-free kinetics viz., Kissinger-Akahira-Sanose, Flynn-Waal-Ozawa and Starink iso-conversional correlations with concomitant evaluation of activation energies (Ea). The Ea value is 194.2 kJ mol-1 at 90% conversion in FWO model, which is higher as compared to other two models. Moisture, volatile substances, and other biochemical components of the biomass were volatilized between 400 and 1000 K in two separate thermo-chemical breakdown regimes. Microscopic and surface characterization analyses were carried out to elucidate the elemental and morphological characteristics of the biomass and biochar. Further, the proficiency of the prepared biochar was tested for removing naphthalene from the watery media. The novelty of the present study lies in extending the applicability of biochar prepared from D. salina for the removal of a model polyaromatic hydrocarbon, naphthalene.

Investigation of adsorption potential of acid violet 90 dye with chitosan/halloysite/boron nitride composite materials

In this study, composite adsorbents consisting of a mixture of chitosan (CTS), boron nitride (h-BN) and halloysite (HNT) were used for the adsorption of Acid Violet 90 (AV90) dye in a batch system. Adsorbents CTS, CTS/HNT, CTS/h-BN and CTS/h-BN/HNT beads were prepared by simple dropping method and dried in a freeze dryer. The beads were characterized by FT-IR, SEM and zeta potential analysis. The effects of pH (2-8) and dye concentration (50-250 mg/L) on AV90 adsorption properties of beads were investigated. In addition, Langmuir, Freunlich, Temkin and Henry adsorption isotherm models were used to examine the dye adsorption mechanism. It was observed that the Langmuir and Freundlich adsorption isotherm models were in good agreement with the experimental data. In the dye concentration range studied, the qm values of CTS, CTS/h-BN1, CTS/h-BN3, CTS/HNT/h-BN1, CTS/HNT/h-BN3, CTS/HNT obtained from the Langmuir isotherm model was 27.62, 17.80, 10.11, 8.71, 32.57, 19.96 mg/g, respectively. Pseudo-first order, pseudo-second order and intra-particle diffusion kinetic models were used to examine the adsorption kinetics of adsorbents. As a result, it is thought that the use of this study in the field of dye adsorption can be an innovative and important study.

Kinetics, Equilibrium, and Thermodynamics for Conjugation of Chitosan with Insulin-Mimetic [meso-Tetrakis(4-sulfonatophenyl)porphyrinato]oxovanadate(IV)(4-) in an Aqueous Solution

This study investigated the conjugation of chitosan with the insulin-mimetic [meso-tetrakis(4-sulfonatophenyl)porphyrinato]oxovanadate(IV)(4-), VO(tpps), in an aqueous medium as a function of conjugation time, VO(tpps) concentrations, and temperatures. To validate the synthesis of chitosan-VO(tpps) conjugate, UV-visible and Fourier transform infrared spectrophotometric techniques were utilized. Conjugate formation is ascribed to the electrostatic interaction between the NH3+ units of chitosan and the SO3- units of VO(tpps). Chitosan enhances the stability of VO(tpps) in an aqueous medium (pH 2.5). VO(tpps) conjugation with chitosan was best explained by pseudo-second-order kinetic and Langmuir isotherm models based on kinetic and isotherm studies. The Langmuir equation determined that the maximal ability of VO(tpps) conjugated with each gram of chitosan was 39.22 μmol at a solution temperature of 45 °C. Activation energy and thermodynamic studies (Ea: 8.78 kJ/mol, ΔG: -24.52 to -27.55 kJ/mol, ΔS: 204.22 J/(mol K), and ΔH: 37.30 kJ/mol) reveal that conjugation is endothermic and physical in nature. The discharge of VO(tpps) from conjugate was analyzed in freshly prepared 0.1 mol/L phosphate buffer (pH 7.4) at 37 °C. The release of VO(tpps) from the conjugate is a two-phase process best explained by the Higuchi model, according to a kinetic analysis of the release data. Taking into consideration all experimental findings, it is proposed that chitosan can be used to formulate both solid and liquid insulin-mimetic chitosan-VO(tpps) conjugates.

Novel hydrogel poly (GG-co-acrylic acid) for the sorptive removal of the color Rhodamine-B from contaminated water

Textile effluent's treatment is highly desired due to the presence of hazardous, water-soluble and non-biodegradable dyes that not only have harmful effect on the environment but on living beings as well. Treatment of these pollutants by sorption through biosorbents is considered to be a best method of choice due to greener nature of the processes. In this connection hydrogel sorbents might be an intriguing option due to its straightforward application, great efficacy, easy synthesis, rapid turnaround, and potential of recycling. Herein, novel hydrogel was prepared using Gellan Gum and acrylic acid (GG-co-AAc) which were then characterized by instrumental techniques like UV/visible and FTIR spectroscopy, SEM, EDX and XRD. The anionic hydrogel's adsorption capacity, swelling behavior, and sorption potential were determined using Rhodamine-B as potential environmental pollutant. The hydrogel exhibited an impressive adsorption capacity of 1250 mg/g. Swelling experiments were performed in Milli-Q distilled water at different pH levels, reaching maximum swelling of 3230% after 23 h as determined through Fickian diffusion. At pH 7, the anionic hydrogel's sorption potential was thoroughly studied in the subsequent experiments. The adsorption process was found to follow the Langmuir isotherm, indicating a monolayer adsorption mechanism supported by higher R2 values compared to the Freundlich isotherm. Thermodynamic analysis revealed the exothermic nature of the adsorption process, with a negative enthalpy value of -11371 KJmol-1 and negative entropy value of -26.39 Jmol-1K-1, suggesting a less ordered system. These findings provide valuable insights into the adsorption characteristics and potential applications of the synthesized anionic hydrogel.

Facile fabrication and application of highly efficient reduced graphene oxide (rGO)-wrapped 3D foam for the removal of organic and inorganic water pollutants

The pace of water contamination is increasing daily due to expanding industrialisation. Finding a feasible solution for effectively remediating various organic and inorganic pollutants from large water bodies remains challenging. However, a nano-engineered advanced hybrid material could provide a practical solution for the efficient removal of such pollutants. This work has reported the development of a highly efficient and reusable absorbent comprising a porous polyurethane (PU) and reduced graphene oxide (rGO) nanosheets (rGOPU) for the removal of different organic oils (industrial oil, engine oil and mustard oil), dyes (MB, MO, RB, EY and MV) and heavy metals (Pb(II), Cr(VI), Cd(II), Co(II) and As(V)). The structure, morphology and properties of the rGOPU hybrid absorbents were analysed by using Raman spectroscopy, field emission scanning electron microscopy (FESEM), Fourier transform infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis (TGA) and Brunner-Emitte-Teller (BET) analysis. The rGOPU possessed both superhydrophobicity and superoleophilicity with water and oil contact angles of about 164° and 0°, respectively. The prepared rGOPU has demonstrated an excellent oil-water separation ability (up to 99%), heavy metals removal efficiency (more than 75%), toxic dye adsorption (more than 55%), excellent recyclability (> 500 times for oils), extraordinary mechanical stability (90% compressible for > 1000 cycles) and high recoverability. This work presents the first demonstration of rGOPU's multifunctional absorbent capacity in large-scale wastewater treatment for effectively removing a wide variety of organic and inorganic contaminants.

Recoverable cellulose composite adsorbents for anionic/cationic dyes removal

GO/HEC/PGDE/Fe₃O₄ materials were successfully fabricated using environmentally-friendly hydroxyethyl cellulose (HEC), poly(ethylene glycol) diglycidyl ether (PGDE), graphene oxide (GO) and magnetic Fe₃O₄. Systematic investigations were completed to explore the influences of GO content in GO/HEC/PGDE/Fe₃O₄ and adsorption conditions on the adsorptions of cationic dyes (methylene blue (MB), crystal violet (CV)) and anionic dye acid blue 25 (AB-25). The increase of GO content can remarkably improve the adsorption capacity of GO/HEC/PGDE/Fe₃O₄ for the dyes. The three kinetic, four isothermic and three thermodynamic models were investigated to reveal the adsorption behaviors of the dyes. The formation of HEC/PGDE/Fe₃O₄ and adsorption mechanisms of the dyes by GO/HEC/PGDE/Fe₃O₄ were suggested. The GO/HEC/PGDE/Fe₃O₄ endowed with easy-fabrication, eco-friendly feature, efficient adsorption capacity of anionic/cationic dyes, convenient separation and reusability has potential applications in wastewater purification industry.

Ultrasonic spray pyrolysis synthesis of TiO2/Al2O3 microspheres with enhanced removal efficiency towards toxic industrial dyes

Developing low-cost and highly effective adsorbent materials to decolorate wastewater is still challenging in the industry. In this study, TiO₂-modified Al₂O₃ microspheres with different TiO₂ contents were produced by spray pyrolysis, which is rapid and easy to scale up. Results reveal that the modification of γ-Al₂O₃ with TiO₂ reduced the crystallite size of Al₂O₃ and generated more active sites in the composite sample. The as-synthesized Al₂O₃-TiO₂ microspheres were applied to remove anionic methyl orange (MO) and cationic rhodamine B (RB) dyes in an aqueous solution using batch and continuous flow column sorption processes. Results show that the Al₂O₃ microspheres modified with 15 wt% of TiO₂ exhibited the maximum adsorbing capacity of ∼41.15 mg g^-1 and ∼32.28 mg g^-1 for MO and RB, respectively, exceeding the bare γ-Al₂O₃ and TiO₂. The impact of environmental complexities on the material's reactivity for the organic pollutants was further delineated by adjusting the pH and adding coexisting ions. At pH ∼5.5, the TiO₂/Al₂O₃ microspheres showed higher sorption selectivity towards MO. In the continuous flow column removal, the TiO₂/Al₂O₃ microspheres achieved sorption capacities of ∼31 mg g^-1 and ∼19 mg g^-1 until the breakthrough point for MO and RB, respectively. The findings reveal that TiO₂-modified Al₂O₃ microspheres were rapidly prepared by spray pyrolysis, and they effectively treated organic dyes in water in batch and continuous flow removal processes.

Black-wattle tannin/kraft lignin H3PO4-activated carbon xerogels as excellent and sustainable adsorbents

This work proposed new black-wattle tannin/kraft lignin H₃PO₄-activated carbon xerogels as sustainable and efficient adsorbents. The precursors were chosen based on their eco-friendly and cost-effective nature, aiming to achieve adsorbents with high adsorption capacities. Carbon xerogels were synthesized through polycondensation with formaldehyde and alkaline catalyst in a simple one-pot procedure. Activation was performed using H₃PO₄ in a tubular furnace (500 °C), under a nitrogen atmosphere. Results show that the inclusion of the kraft lignin led to changes in the morphology of the materials, facilitating the development of their porous structure and increasing specific surface area and pore volume. The best adsorbent (XLT 50 %) was synthesized using a 1:1 tannin/kraft lignin mass ratio. This material presented an adsorption capacity of nearly 1150 mg g^-1 of methylene blue (pH = 5 and T = 298 K), which was linked to its high specific surface area of 1348 m² g^-1. The adsorption process followed the pseudo-second-order kinetic model, whereas the adsorption isotherms were best fitted by the Sips model. The XLT 50 % presented good reusability properties, maintaining its adsorption capacity for 3 cycles. Finally, the XLT 50 % presented good adsorptive properties toward other pollutants (methyl orange, 4-chlorophenol, and hexavalent chromium), indicating its versatility for adsorption processes.

Synthesis and adsorption performance of three-dimensional gels assembled by carbon nanomaterials for heavy metal removal from water: A review

This review focuses on the removal of heavy metals from water by three-dimensional gels with carbon nanomaterials as the main building units. It highlights the fundamental knowledge, most recent advances, and future prospects of carbon nanomaterial-assembled gels (CNAGs) as effective adsorbents for heavy metals in water. Various synthesis methods of CNAGs including template-assisted, self-assembly and other methods are systematically summarized and evaluated. Adsorption performances of CNAGs to typical cationic and anionic heavy metals, especially lead, cadmium, mercury, chromium, and arsenic, are thoroughly examined and discussed in detail. These analyses bring out that composite CNAGs constructed from carbon nanomaterials with polymers or other engineered nanoparticles are the most promising adsorbents for heavy metal removal from water. Current challenges and future research directions that are critical to the applications of CNAGs in the removal of heavy metals from contaminated water are outlined at the end of the review.

Adsorption of caffeine using steel wastes

Caffeine is the most widespread active pharmaceutical compound in the world, generally studied as a tracer of human pollution, since caffeine levels in surface water correlate with the anthropogenic load of domestic wastewater. This work investigated the use of different steel wastes named as SW-I, SW-II, SW-II, SW-IV, SW-V, and SW-VI in the adsorption of caffeine. These materials were pretreated and characterized by scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray diffraction, and point of zero charge. The samples are mainly composed of iron (hematite and magnetite). The caffeine adsorption test indicated that SW-VI (steel slag dust) is the most efficient and promising (removal around 51.68%) in relation to the other residues, which it was selected for further studies. Equilibrium time was reached within 96 h of contact between the adsorbent and the adsorbate, with removal of 84.00%, 81.09%, and 73.19% for the initial concentrations of 10 mg L-1, 20 mg L-1, and 30 mg L-1 of caffeine. The pseudo-first-order, pseudo-second-order, and Elovich models presented a good fit to the experimental data. However, the pseudo-first order model described better the experimental behavior. Adsorption isotherms were performed at three temperatures (298, 308, and 318 K). The maximum adsorption capacity was 17.46 ± 2.27 mg g-1, and experimental data were better fitted by the Sips isotherm. Values of ΔG° and parameters equilibrium of the models of Langmuir, Sips, and Temkin were calculated from the standard enthalpies and standard entropies estimated. The values of ΔG° were negative for the temperatures studied indicating that the adsorption process is viable and spontaneous. Negative values for ΔH° were also found, indicating that the process of caffeine adsorption by SW-VI is an exothermic process (0 to -40 kJ mol-1). Thus, the adsorption of caffeine by SW-VI is a physical process. The SW-VI material showed economic viability and promising for the adsorption of caffeine in aqueous media.

Methylene Blue Adsorption BY UV-Treated Graphene Oxide Nanoparticles (UV/n-GO): Modeling and Optimization Using Response Surface Methodology and Artificial Neural Networks

To mitigate the negative effects of pollution produced by the growing levels of pollutants in the environment, research and development of novel and more effective materials for the treatment of pollutants originating from a variety of industrial sources should be prioritized. In this research, a UV-irradiated nano-graphene oxide (UV/n-GO) was developed and studied for methylene blue (MB) adsorption. Furthermore, the batch adsorption studies were modelled using response surface modelling (RSM) and artificial neural networks (ANNs). Investigations employing FTIR, XRD, and SEM were carried out to characterize the adsorbent. The best MB removal of 95.81% was obtained at a pH of 6, a dose of 0.4 g/L, an MB concentration of 25 mg/L, and a period of 40 min. This was accomplished with a desirability score of 0.853. A three-layer backpropagation network with an ideal structure of 4-4-1 was used to create an ANN model. The R2 and MSE values determined by comparing the modelled data with the experimental data were 0.9572 and 0.00012, respectively. The % MB removal predicted by ANN was 94.76%. The kinetics of adsorption corresponded well with the pseudo-second-order model (R2 > 0.97). According to correlation coefficients, the order of adsorption isotherm models is Redlich–Peterson > Temkin > Langmuir > Freundlich. Thermodynamic investigations show that MB adsorption was both spontaneous and endothermic.

Eco-Friendly NiO/Polydopamine Nanocomposite for Efficient Removal of Dyes from Wastewater

The rapid development of industries discharges huge amounts of wastewater that contain surface water. For this reason, we used NiO/polydopamine (NiO/PDA) nanocomposite as an efficient material for the removal of Methyl violet 2B from water. It was synthesized and then characterized by Fourier Transform Infrared (FT-IR) spectroscopy, X-ray Diffraction (XRD), Scanning Electron Microscopy (SEM), Energy Dispersive X-ray (EDX) analysis, Transmission Electron Microscopy (TEM), and Brunauer–Emmett–Teller (BET). The EDX analysis confirmed the presence of O, Ni, N, and C. The composite has an average particle size of 18 nm. Its surface area is 110.591 m2/g. It was found that the efficiency of dye removal by adsorption on NiO/PDA exceeded that of bare NiO. The adsorption capacity of NiO and NiO/PDA are 126 and 284 mg/g, respectively. The effects of adsorbent dose, dye concentration, and pH on the removal efficiency were examined. The efficiency increased with increasing the adsorbent dose and pH, but dropped from 85 to 73% within 30 min as the initial dye concentration was increased from 0.984 to 4.92 mg/L. Such a drop in the removal efficiency is due to the blocking of the surface-active sites of NiO/PDA, with the high population of dye molecules derived from the continuous increase in dye concentration. The adsorption results of the dye fitted well with the pseudo-second-order kinetics and Langmuir isotherm. The reusability data showed that NiO/PDA was stable across three adsorption–regeneration cycles, thus it can be considered a good recyclable and efficient adsorbent. Because of these results, it can be considered that this method can be applied for the treatment of wastewater.

Synthesis of 3D graphene-based materials and their applications for removing dyes and heavy metals

Contamination of water streams by dyes and heavy metals has become a major problem due to their persistence, accumulation, and toxicity. Therefore, it is essential to eliminate and/or reduce these contaminants before discharge into the natural environment. In recent years, 3D graphene has drawn intense research interests owing to its large surface area, superior charge conductivity, and thermal conductivity properties. Due to their unique surface and structural properties, 3D graphene-based materials (3D GBMs) are regarded as ideal adsorbents for decontamination and show great potential in wastewater or exhaust gas treatment. Here, this minireview summarizes the recent progress on 3D GBMs synthesis and their applications for adsorbing dyes and heavy metals from wastewater based on the structures and properties of 3D GBMs, which provides valuable insights into 3D GBMs' application in the environmental field.

Adsorptive removal of Sr(II) from aqueous solution by polyvinyl alcohol/graphene oxide aerogel

In this study, a new adsorbent, polyvinyl alcohol (PVA) and graphene oxide (GO), was prepared, characterized and used for the removal of Sr²⁺ from aqueous solution. In PVA/GO composite, the inter-lamellar spacing of adjacent GO layers was dramatically enlarged due to the intercalation of PVA molecules, such a unique architecture significantly mitigated the aggregation of GO layers, which facilitated the accessible exposure of active sites and the mass transfer of strontium ions (Sr²⁺), thus enhancing the adsorption capacity toward Sr²⁺. The adsorption of Sr²⁺ by PVA/GO composite conformed to the pseudo second-order kinetic model (R² = 0.9994), the Langmuir model (R² = 0.9042), and the Freundlich model (R² = 0.9598). The complexation interaction between Sr²⁺ and oxygen atoms/π-electron domain of PVA/GO composite was primarily responsible for the adsorption mechanism, based on the characterization results of X-ray photoelectron spectroscopy (XPS), scanning electron microscope equipped with energy dispersion spectroscopy (SEM-EDS) and powder X-ray diffraction (PXRD).

Removal of perfluorooctanoic acid (PFOA) from aqueous solution by amino-functionalized graphene oxide (AGO) aerogels: Influencing factors, kinetics, isotherms, and thermodynamic studies

Perfluorooctanoic acid (PFOA) is an emerging organic pollutant that has become ubiquitous in waterways and is difficult to be removed from wastewater using traditional treatment methods. In this study, amino-functionalized graphene oxide (AGO) aerogels were prepared as a potential remediation tool for water contaminated by PFOA. The structure of the prepared absorbent material was characterized by Fourier transform infrared spectroscopy, Raman spectroscopy, scanning electron microscope, and X-ray diffraction. The use of various adsorption times, temperatures, solution pH, and absorbent amount were investigated to determine optimum conditions for PFOA adsorption. Adsorption kinetics and thermodynamics of the absorbent were analyzed as well. AGO aerogels exhibited a high adsorption capacity of PFOA (1575 mg∙g^-1) and high removal efficiency (99.95%) in a solution containing 10 mg PFOA L^-1, likely due to the interconnected porous microstructures and amino groups of the AGO aerogels. The adsorption kinetics and isotherm of PFOA were well-fitted using pseudo-second-order and the Freundlich modelling. The adsorption mechanism of PFOA onto AGO aerogels followed spontaneous, exothermic, and physical processes. This study shows the potential of this material to remove PFOA from PFOA-contaminated waters effectively by providing insight into the understanding of the adsorption mechanisms of PFOA onto AGO aerogels.

Ecofriendly biopolymers and composites: Preparation and their applications in water-treatment

Over the past few decades, the term polymer has been repeatedly used in several industries for their immense characteristics in different applications. Polymers and their composites which were prepared from chemical monomer sources turned out to be potentially harmful to the environment due to their tedious degradation process. Biopolymers are natural substitutes for synthetic polymers which can be efficiently extricated from natural sources. They are predominantly available as polymeric units as well as monomeric units that are linked covalently. These environment-friendly biopolymers and their composites can be categorized based on their numerous sources, different methods of preparation and their potential form of usage. They were found to be biocompatible and biodegradable which make them exceptionally useful in environment based applications, mainly in the process of water treatment, both potable and wastewater. Further, the biopolymer and biopolymer composites easily fit into different parts of the treatment process by acting as filtration media, adsorbents, coagulants and as flocculants. The primary focus of this review is to provide a comprehensive information of biopolymers and biopolymer composites from synthesis to their usefulness for their productive application in water treatment processes. On the whole, it can be substantiated that the biopolymers were identified to play a notable adversary to the synthetic polymers in treating waters with an indispensable need for an elaborative study in the production of the biopolymers.

Progress in modifications of 3D graphene-based adsorbents for environmental applications

3D graphene-based materials are promising adsorbents for environmental applications. Furthermore, increasing attention has been paid to the improvement of 3D graphene adsorbents for removing pollutants. In this article, the progress in the modification of 3D graphene materials and their performance for removing pollutants were reviewed. The modification strategies, which were classified as (1) the activation with CO₂ (steam and other oxidants) and (2) the surface functionalization with polymers (metals, and metal oxides), were evaluated. The performances of modified 3D graphene materials were assessed for the removal of waste gases (such as CO₂), refractory organics, and heavy metals. The challenges and future research directions were discussed for the environmental applications of 3D graphene materials.

Mechanistic understanding of highly selective adsorption of bisphenols on microporous-dominated nitrogen-doped framework carbon

Producing a desirable adsorbent for removing endocrine disrupting compounds (EDCs) from aqueous solutions remains a major challenge. In this work, microporous-dominated nitrogen-doped framework carbons (MNFCs, s means the calcination temperature) with high specific surface area, ultra-microporous structure, and high nitrogen-doping can be obtained by a direct calcination of ethylene diamine tetraacetic acid tetrasodium (EDTA-4Na) without aid of any catalyst and nitrogen source. MNFCs were applied adsorbents to remove bisphenols from aqueous solution. Batch experiments showed MNFC-750 had a large adsorption capacity for bisphenols from aqueous solutions (409 mg/g for bisphenol A, 364 mg/g for bisphenol F, and 521 mg/g for bisphenol S) along with short equilibrium time (30 min), and good stability and reusability. Using multiple characterizations and comparative experiments along with theoretical calculations, we discovered that: (1) nitrogen-doping can significantly boost the adsorption capacity; (2) adsorption sites are mainly the pyridinic-N instead of pyrrolic-N and graphitic-N; and (3) the adsorption mechanisms were mainly driven by Lewis acid-base interaction, hydrophobic interaction, π-π interaction and hydrogen bond interaction. These findings indicate that MNFCs present a promising potential for practical applications and shed light on the rational design of nitrogen doped carbon-based adsorbents for efficient pollutant removal.

Defect-Induced Double-Stranded DNA Unwinding on Graphene

Several works have shown that graphene materials can effectively regulate the double-stranded DNA (dsDNA) structures and are used to remove antibiotic resistance genes in the environment, during which the morphology of the graphene surface plays a key role. However, the mechanism of how different graphene surfaces interact with dsDNA is poorly documented. Here, the interactions of dsDNA with defective graphene (D-Gra) and pristine graphene (P-Gra) have been explored by molecular dynamics simulations. Our data clearly showed that both D-Gra and P-Gra were able to attract dsDNA to form stable bindings. However, the structure evolutions of dsDNA are distinctly different. In detail, D-Gra can initiate quick unwinding of dsDNA and cause significant structural disruption. While for P-Gra, it demonstrated a much weaker capability to disrupt the dsDNA structure. This difference is due to the strong electrostatic interaction between defects and DNA nucleotides. Nucleotides can be highly restricted by the defect while the other parts of dsDNA could move along the transverse directions of D-Gra. This effectively introduces a "pulling force" from the defect that causes the breaking of the hydrogen bonds between dsDNA base pairs. Such force finally leads to the serious unwinding of dsDNA. Our present findings could help us to better understand the molecular mechanism of how the dsDNA canonical B-form was lost upon adsorption to graphene. The findings of the key roles of defects on graphene are beneficial for the design of functional graphenic materials for biological and medical applications through nanostructure engineering.

Recent Developments in Chitosan-Based Adsorbents for the Removal of Pollutants from Aqueous Environments

The quality of water is continuously under threat as increasing concentrations of pollutants escape into the aquatic environment. However, these issues can be alleviated by adsorbing pollutants onto adsorbents. Chitosan and its composites are attracting considerable interest as environmentally acceptable adsorbents and have the potential to remove many of these contaminants. In this review the development of chitosan-based adsorbents is described and discussed. Following a short introduction to the extraction of chitin from seafood wastes, followed by its conversion to chitosan, the properties of chitosan are described. Then, the emerging chitosan/carbon-based materials, including magnetic chitosan and chitosan combined with graphene oxide, carbon nanotubes, biochar, and activated carbon and also chitosan-silica composites are introduced. The applications of these materials in the removal of various heavy metal ions, including Cr(VI), Pb(II), Cd(II), Cu(II), and different cationic and anionic dyes, phenol and other organic molecules, such as antibiotics, are reviewed, compared and discussed. Adsorption isotherms and adsorption kinetics are then highlighted and followed by details on the mechanisms of adsorption and the role of the chitosan and the carbon or silica supports. Based on the reviewed papers, it is clear, that while some challenges remain, chitosan-based materials are emerging as promising adsorbents.

High-temperature liquid chromatography for evaluation of the efficiency of multiwalled carbon nanotubes as nano extraction beds for removal of acidic drugs from wastewater. Greenness profiling and comprehensive kinetics and thermodynamics studies

The retention behavior of a series of acidic drugs, namely ketoprofen (KET), naproxen (NAP), diclofenac (DIC), and ibuprofen (IBU), on the heat-resisting ZORBAX 300SB-C₁₈ column, was studied thermodynamically using high-temperature liquid chromatography (HTLC). A perfect correlation of the compounds' lipophilicity and the calculated thermodynamic indicators evidenced its contribution to the retention behavior. Besides, the steric fitting has a subsidiary effect on IBU retention. Isocratic HTLC separation of the four compounds was achieved using an aqueous mobile phase containing 30% acetonitrile-0.2% acetic acid-0.2% triethylamine at 60 °C. This method has been utilized to monitor the adsorption efficiency of multiwalled carbon nanotubes (MWCNTs) for the removal of the four NSAIDs from water. Different variables affecting the remediation process have been optimized such as the time of contact, pH, ionic strength, temperature, and the mass of MWCNTs. The kinetics and thermodynamics of the adsorption were investigated. The adsorption was evidenced to take place via pseudo-second-order kinetics and the intraparticle diffusion is the rate-controlling step. The thermodynamic investigation showed that the adsorption process is exothermic and enthalpy-driven, and the adsorption is more extensive at a lower temperature. The MWCNTs showed excellent adsorption efficiency of about 76.4 to 97.6% at the optimum conditions. The obtained results are promising and encouraging for the full-scale application of MWCNTs for remediation of NSAIDs-related water pollution. The green analytical chemistry metric "AGREE" and the analytical eco-scale score tool confirmed that the developed protocol is greener and more favorable to the environment and user than most of the reported literature.

Removal of Phenolic Compounds from Olive Mill Wastewater by a Polydimethylsiloxane/oxMWCNTs Porous Nanocomposite

User-friendly and energy-efficient methods able to work in noncontinuous mode for in situ purification of olive mill wastewater (OMW) are necessary. Herein we determined the potential of oxidized multiwalled carbon nanotubes entrapped in a microporous polymeric matrix of polydimethylsiloxane in the removal and recovery of phenolic compounds (PCs) from OMW. The fabrication of the nanocomposite materials was straightforward and evidenced good adsorption capacity. The adsorption process is influenced by the pH of the OMW. Thermodynamic parameters evidenced the good affinity of the entrapped nanomaterial towards phenols. Furthermore, the kinetics and adsorption isotherms are studied in detail. The presence of oil inside the OMW can speed up the uptake process in batch adsorption experiments with respect to standard aqueous solutions, suggesting a possible use of the nanocomposite for fast processing of OMW directly in the tank where they are stored. Moreover, the prepared nanocomposite is safe and can be easily handled and disposed of, thus avoiding the presence of specialized personnel. After the adsorption process the surface of the nanomaterial can be easily regenerated by mild treatments with diluted acetic acid, thus permitting both the recyclability of the nanomaterial and the recovery of phenolic compounds for a possible use as additives in food and nutraceutical industries and the recovery of OMW for fertirrigation.

Adsorptive oxidation of sulfides catalysed by δ-MnO2 decorated porous graphitic carbon composite

Removal of dissolved sulfide contaminants from aqueous model solution using bio-derived porous graphitic carbon (PGC) impregnated with δ-MnO₂ was investigated. The composite adsorbent was synthesized using the chemical wet deposition method wherein MnO₂ was deposited on carbon walls through an in-situ reaction between permanganate and ethanol. Formation of transition metal oxide of manganese in the form of birnessite nanoparticles on interconnected PGC cell structure was confirmed by transmission electron microscopy, scanning electron microscopy, elemental analysis, and X-Ray diffraction characterization studies. The composite nanomaterial was tested for sulfide removal from aqueous solution at various conditions, including the pH, adsorbent dosage, initial solution concentration, and contact time. Adsorption results demonstrated an excellent adsorption capacity of ca. 90% within 20 min of contact time at 298 K. Equilibrium data collected from batch adsorption experiments fitted well with the Langmuir isotherm model (K_L = 190 L/mg; R² = 0.99). The maximum adsorption capacity of the composite was estimated as 526.3 mg S^2-/g at highly alkaline conditions compared to ca. 340 mg/g for a δ-MnO₂ adsorbent. Adsorptive oxidation of sulfides on composite MnO₂-PGC adsorbent was found to be controlled by the chemisorption process in accordance with the pseudo-second-order reaction model. Characterization of spent adsorbents revealed that sulfide was removed through adsorptive oxidation resulting in the formation of agglomerated particles of metal sulfate complexes and elemental sulfur. Analysis of reaction mechanism revealed that both MnO₂ and PGC played a role in the adsorptive oxidation of sulfides to CaSO₄ and elemental sulfur.

Speciation, toxicity mechanism and remediation ways of heavy metals during composting: A novel theoretical microbial remediation method is proposed

Heavy metals (HM) pollution is a major limitation to the application of composting products. Therefore, mitigating the toxicity of HM has attracted wide attention during composting. The toxicity of HM is mainly acted on microorganisms during composting, and the toxicity of different HM speciation is obviously various. There are many pathways to change the speciation to reduce the toxicity during composting. Therefore, in this review, the speciation distribution, toxicity mechanism and remediation ways of HM during composting were discussed in order to better solve HM pollution. The microbial remediation technology holds enormous potential to remediate for HM without damaging composting, however, it is hard to extract HM. The innovation of this review was to outline microbial remediation strategies for HM during composting based on two mechanisms of microbial remediation: extracellular adsorption and intracellular sequestration, to solve the problem how to extract microbial agents from the compost. Ultimately, a novel theoretical method of microbial remediation was proposed to remove HM from the compost.

An analysis of the versatility and effectiveness of composts for sequestering heavy metal ions, dyes and xenobiotics from soils and aqueous milieus

The persistence and bioaccumulation of environmental pollutants in water bodies, soils and living tissues remain alarmingly related to environmental protection and ecosystem restoration. Adsorption-based techniques appear highly competent in sequestering several environmental pollutants. In this review, the recent research findings reported on the assessments of composts and compost-amended soils as adsorbents of heavy metal ions, dye molecules and xenobiotics have been appraised. This review demonstrates clearly the high adsorption capacities of composts for umpteen environmental pollutants at the lab-scale. The main inferences from this review are that utilization of composts for the removal of heavy metal ions, dye molecules and xenobiotics from aqueous environments and soils is particularly worthwhile and efficient at the laboratory scale, and the adsorption behaviors and effectiveness of compost-type adsorbents for agrochemicals (e.g. herbicides and insecticides) vary considerably because of variabilities in structure, topology, bond connectivity, distribution of functional groups and interactions of xenobiotics with the active humic substances in composts. Compost-based field-scale remediation of environmental pollutants is still sparse and arguably much challenging to implement if, furthermore, real-world soil and water contamination issues are to be addressed effectively. Hence, significant research and process development efforts should be promptly geared and intensified in this direction by extrapolating the lab-scale findings in a cost-effective manner.

Graphene/waste-newspaper cellulose composite aerogels with selective adsorption of organic dyes: preparation, characterization, and adsorption mechanism

Waste-newspaper cellulose/graphene composite aerogels were facilely synthesized via the sol–gel and freeze-drying processes for dye wastewater treatment.

Graphene oxide as a tool for antibiotic-resistant gene removal: a review

Environmental pollutants, including antibiotics (ATBs), have become an increasingly common health hazard in the last several decades. Overdose and abuse of ATBs led to the emergence of antibiotic-resistant genes (ARGs), which represent a serious health threat. Moreover, water bodies and reservoirs are places where a wide range of bacterial species with ARGs originate, owing to the strong selective pressure from presence of ATB residues. In this regard, graphene oxide (GO) has been utilised in several fields including remediation of the environment. In this review, we present a brief overview of resistant genes of frequently used ATBs, their occurrence in the environment and their behaviour. Further, we discussed the factors influencing the binding of nucleic acids and the response of ARGs to GO, including the presence of salts in the water environment or water pH, because of intrinsic properties of GO of not only binding to nucleic acids but also catalysing their decomposition. This would be helpful in designing new types of water treatment facilities.

Environmental application of three-dimensional graphene materials as adsorbents for dyes and heavy metals: Review on ice-templating method and adsorption mechanisms

The remediation of wastewater requires treatment technologies which are robust, efficient, simple to operate and affordable such as adsorption. Lately, three-dimensional (3D) graphene based materials have attracted significant attention as effective adsorbents for wastewater treatment. The intrinsic properties of 3D graphene structure such as large surface area and interconnected porous structure can facilitate the transport of pollutants into the 3D network and provide abundant active sites for trapping the pollutants. For the synthesis of 3D graphene structure, ice-templating is commonly practiced due to its facile steps, cost effectiveness and high scalability potential. This review covers the ice-templating fabrication technique for 3D graphene based materials and their application as adsorbents in eliminating dyes and heavy metals from aqueous media. The assembly mechanisms of the ice-templating fsynthesis are comprehensively discussed. Further discussion on the fundamental principles, critical process parameters and characteristics of ice-templated 3D graphene structures is also included. A thorough review on the mechanisms for batch adsorption of dyes and heavy metals is presented based on the structures and properties of the 3D graphene materials. The review further evaluates the dynamic adsorption in packed columns and the regeneration of 3D graphene based materials.

Advances in the applications of graphene adsorbents: from water treatment to soil remediation

Graphene, a novel carbon allotrope, is single-layered graphite with honeycomb lattice. Its unique structure endows graphene many outstanding physical/chemical properties and a large surface area, which are beneficial to its applications in many areas. The potential applications of graphene in pollution remediation are adsorption, membrane separation, catalysis, environmental analysis, and so on. The adsorption efficiency of graphene adsorbents largely depends on its surface area, porous structure, oxygen-containing groups and other functional groups, adsorption conditions, and also the properties of adsorbates. With appropriate modifications, graphene materials are mostly efficient adsorbents for organic pollutants (e.g. dyes, pesticides, and oils) and inorganic pollutants (e.g. metal ions, nonmetal ions, and gas). Since our first report of graphene adsorbents in 2010, plenty of studies have been dedicated to developing various graphene adsorbents and to evaluating their performance in treating contaminated water. Recently, there is a growing trend in graphene adsorbents that could be applied in soil remediation, where the situation is much more complicated than in aqueous systems. Herein, we review the design of graphene adsorbents for water treatment and analyze their potential in soil remediation. Several suggestions to accelerate the research on graphene-based soil remediation technology are proposed.

Response of antibiotic resistance genes abundance by graphene oxide during the anaerobic digestion of swine manure with copper pollution

The pollution of various environments with antibiotic resistance genes (ARGs) is an urgent problem that needs to be addressed, especially in heavy metal-polluted environments. This study investigated the responses of ARGs and mobile genetic elements (MGEs) to the addition of graphene oxide (GO) to swine manure containing a high concentration copper during anaerobic digestion. The total copy numbers of ARGs and MGEs were significantly enhanced by the pressure due to Cu. GO significantly decreased the ARG and MGE copy numbers, where the low GO concentration performed better than the high GO concentration. Network analysis showed that most of the ARGs and MGEs co-occurred and they shared the same major potential host bacteria. The contributions of different factors to ARG abundances were assessed by redundancy analysis and MGEs had the most important effect on the fate of ARGs. Thus, GO may reduce the abundance of ARGs mainly by removing MGEs.

Preparation of gemini surfactant/graphene oxide composites and their superior performance for Congo red adsorption

Gemini surfactant/GO composites (10-2-10/GO, 12-2-12/GO, and 14-2-14/GO) have been successfully prepared using three gemini surfactants with different tail chain lengths. The morphology and physicochemical properties of the as-synthesized composites were characterized by scanning electron microscopy, transmission electron microscopy, Fourier transform-infrared spectroscopy, X-ray diffraction, and X-ray photoelectron spectroscopy. The gemini surfactant/GO composites were applied to the adsorption of Congo red dye, and from the experimental data, optimum adsorption conditions, adsorption kinetics, and isotherms were obtained. The removal process was favorable at acidic pH and reached equilibrium in ∼60 min. The results showed that the pseudo-second-order model and the Langmuir adsorption isotherm were a good fit for the adsorption of Congo red onto gemini surfactant/GO composites. Compared with other adsorbents reported in the literature, these composites showed superior Congo red adsorption capabilities, with absorption capacities as high as 2116, 2193, and 2325 mg g⁻¹ for 10-2-10/GO, 12-2-12/GO, and 14-2-14/GO, respectively. Moreover, the adsorption capacities were more than 1000 mg g⁻¹ even for the fifth cycle. The results of the present study substantiate that the gemini surfactant/GO composites are promising adsorbents for the removal of organic dyes in wastewater treatment.

Gemini surfactant/GO composites were prepared for the removal of Congo red dye, and show excellent adsorption capacities and reusabilities.