Environmental behavior of engineered nanomaterials in porous media: a review

Transport of polystyrene microplastics in bare and iron oxide-coated quartz sand: Effects of ionic strength, humic acid, and co-existing graphene oxide

This research explored the effects of widely utilized nanomaterial graphene oxide (GO) and organic matter humic acid (HA) on the transport of microplastics under different ionic solution strengths in bare sand and iron oxide-coated sand. The results found transport of polystyrene microplastics (PS) did not respond to the presence of HA in sand that contains large amounts of iron oxide. Compared to bare quartz sand, ionic strength had little effect: <20 % of PS passed through Fe sand columns. There was a significant promotion of PS transport in the presence of GO, however, which can be attributed to the increased surface electronegativity of PS and steric hindrance. Moreover, GO combined with HA significantly promoted the transport of PS in the Fe sand, and transport further increased when the concentration of HA increased from 5 to 10 mg/L. Interestingly, the degree of this increase exactly corresponded to the change in the surface charge of the microplastics, demonstrating that electrostatic interaction dominated the PS transport. Further results indicated that co-existing pollutants had significant impacts on the transport of microplastics under various conditions by altering the surface characteristics of the plastic particles and the spatial steric hindrance within porous media. This research will offer insights into predicting the transport and fate of microplastics in complex environments.

Multi-functional copper oxide nanoparticles synthesized using Lagerstroemia indica leaf extracts and their applications

Developing multifunctional nanomaterials through environmentally friendly and efficient approaches is a pivotal focus in nanotechnology. This study aimed to employ a biogenic method to synthesize multifunctional copper oxide nanoparticles (LI-CuO NPs) with diverse capabilities, including antibacterial, antioxidant, and seed priming properties, as well as photocatalytic organic dye degradation and wastewater treatment potentials using Lagerstroemia indica leaf extract. The synthesized LI-CuO NPs were extensively characterized using UV-vis spectroscopy, dynamic light scattering (DLS), X-ray diffraction (XRD), scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM-EDX), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), and Fourier transform-infrared spectroscopy (FT-IR). The colloid displayed surface plasmon resonance peaks at 320 nm, characteristic of LI-CuO NPs. DLS analysis revealed an average particle size of 93.5 nm and a negative zeta potential of -20.3 mV. FTIR and XPS analyses demonstrated that LI-CuO NPs possessed abundant functional groups that acted as stabilizing agents. XRD analysis indicated pure crystalline and spherical LI-CuO NPs measuring 36 nm in size. Antibacterial tests exhibited significant differential activity of LI-CuO NPs against both gram-negative (Escherichia coli, Salmonella typhimurium) and gram-positive (Staphylococcus aureus and Listeria monocytogenes) bacteria. In antioxidant tests, the LI-CuO NPs demonstrated a remarkable radical scavenging activity of 97.6 % at a concentration of 400 μg mL-1. These nanoparticles were also found to enhance mustard seed germination at low concentrations. With a remarkable reusability, LI-CuO NPs exhibited excellent photocatalytic performance, with a degradation efficiency of 97.6 % at 150 μg/mL as well as a 95.6 % reduction in turbidity when applied to wastewater treatment. In conclusion, this study presents environmentally friendly method for the facile synthesis of LI-CuO NPs that could potentially offer promising applications in biomedicine, agriculture, and environmental remediation due to their multifunctional properties.

Statuses, shortcomings, and outlooks in studying the fate of nanoplastics and engineered nanoparticles in porous media respectively and borrowable sections from engineered nanoparticles for nanoplastics

This review discussed the research statuses, shortcomings, and outlooks for the fate of nanoplastics (NPs) and engineered nanoparticles (ENPs) in porous media and borrowable sections from ENPs for NPs. Firstly, the most important section was that we reviewed the research statuses on the fate of NPs in porous media and the main influencing factors, and explained the influencing mechanisms. Secondly, in order to give NPs a reference of research ideas and influence mechanisms, we also reviewed the research statuses on the fate of ENPs in porous media and the factors and mechanisms influencing the fate. The main mechanisms affecting the transport of ENPs were summarized (Retention or transport modes: advection, diffusion, dispersion, deposition, adsorption, blocking, ripening, and straining; Main forces and actions: Brownian motion, gravity, electrostatic forces, van der Waals forces, hydration, filtration, bridging; Affecting elements of the forces and actions: the ENP and media grain surface functional groups, size, shape, zeta potential, density, hydrophobicity, and roughness). Instead of using the findings of ENPs, thorough study on NPs was required because NPs and ENPs differed greatly. Based on the limited existing studies on the NP transport in porous media, we found that although the conclusions of ENPs could not be applied to NPs, most of the influencing mechanisms summarized from ENPs were applicable to NPs. Combining the research thoughts of ENPs, the research statuses of NPs, and some of our experiences and reflections, we reviewed the shortcomings of the current studies on the NP fate in porous media as well as the outlooks of future research. This review is very meaningful for clarifying the research statuses and influence mechanisms for the NP fate in porous media, as well as providing a great deal of inspiration for future research directions about the NP fate in porous media.

Aquatic Ecosystem Risk Assessment Generated by Accidental Silver Nanoparticle Spills in Groundwater

This paper aims to create a new model for assessing the ecosystem risk in rivers and wetlands that are linked to accidental spills of silver nanoparticles (AgNPs) in soil/groundwater. Due to the uncertainty of the modeling inputs, a combination of two well-known risk assessment methodologies (Monte Carlo and fuzzy logic) were used. To test the new model, two hypothetical, accidental AgNP soil spill case studies were evaluated; both of which were located at the end of the Llobregat River basin within the metropolitan area of Barcelona (NE Spain). In both cases, the soil spill reached groundwater. In the first case, it was discharged into a river, and in the second case, it recharged a wetland. Concerning the results, in the first case study, a medium-risk assessment was achieved for most cases (83%), with just 10% of them falling below the future legal threshold concentration value. In the second case study, a high-risk assessment was obtained for most cases (84%), and none of the cases complied with the threshold value. A sensitivity analysis was conducted for the concentration and risk. The developed tool was proven capable of assessing risk in aquatic ecosystems when dealing with uncertain and variable data, which is an improvement compared to other risk assessment methodologies.

Biosurfactant-mediated mobility of graphene oxide nanoparticles in saturated porous media

There is currently a lack of scientific understanding regarding how bio-surfactants influence the mobility of graphene oxide (GO) through saturated porous media. In this study, the transport characteristics of GO through porous media with different heterogeneities (i.e., quartz sand and goethite-coated sand) after the addition of saponin (a representative bio-surfactant) were investigated. The results demonstrated that saponin (3-10 mg L^-1) promoted GO mobility in both types of porous media at pH 7.0. This trend was attributed to the competitive deposition between nanoparticles and bio-surfactant molecules for attachment sites, the enhanced electrostatic repulsion, the decreased strain, the presence of steric effects induced by the adsorbed saponin, and the increase in the hydrophilicity of nanoparticles. Intriguingly, saponin promoted GO mobility in goethite-coated sand (i.e., chemically heterogeneous porous media) to a greater extent than that in sand (i.e., relatively homogeneous porous media) when saponin concentrations increased, which stemmed from the differences in the extent of the deposition site competition for saponin on the two porous media and the electrostatic repulsion between GO and the porous media. Furthermore, a cation-bridging mechanism was also involved in the ability of saponin to increase GO mobility when the electrolyte solution was 0.1 mM Cu²⁺. Moreover, the extended Derjaguin-Landau-Verwey-Overbeek (XDLVO) theory and the colloid transport model were applicable to elucidate the mobility properties of GO with or without saponin in porous media. The findings from this work highlight the important status of bio-surfactants in the fate of colloidal carbon-based nanomaterials in subsurface systems.

Enhancing effects of dissolved and media surface-bound organic matter on titanium dioxide nanoparticles transport in iron oxide-coated porous media under acidic conditions

Natural organic matter (NOM) and iron oxides have been proved to be crucial factors controlling the behaviors of nanoparticles in heterogenous environment. Here, we conducted experimental and modeling study on the transport of titanium dioxide nanoparticles (TiO₂ NPs) in iron oxide-coated quartz in the presence of NOM under acidic conditions. Results showed the antagonistic effects of iron oxides and NOM on TiO₂ NPs mobility. The inhibition of iron oxides coated on quartz was crystal form-dependent other than quantity-dependent. Amorphous ferric oxyhydroxide with higher specific surface area brought more positive charge and favorable deposition sites onto quartz, and induced more retention of nanoparticles than two crystalline iron oxides, goethite and hematite. Dissolved organic matter (DOM) facilitated TiO₂ NPs transport in iron oxide-coated quartz. In comparation with the limited enhancing effects of DOM, the NOM coatings on media surface partially or largely offset the inhibition of goethite on nanoparticles mobility through direct occupation of attachment sites and sites screening due to the steric repulsion of the macromolecules. Owing to the higher steric hindrance, humic acid, both in dissolved and media surface-bound states, exerted stronger facilitating effects on TiO₂ NPs mobility relative to fulvic acid.

Transport and targeted binding of Pluronic-coated nanoparticles in unsaturated porous media

The effectiveness of most in situ remedial technologies, including nanoremediation, lies on successful delivery of reagents to a subsurface target treatment zone. Targeted delivery of engineered nanoparticles (NPs) to treat petroleum hydrocarbons present in the unsaturated zone requires an understanding of their transport behaviour in these systems. A series of column experiments explored the effect of initial water saturation, flowrate, input dosage, and porous medium texture on the transport of iron oxide or cobalt ferrite NPs coated with an amphiphilic co-polymer, as well as their targeted attachment to a crude oil zone. As the initial water content increased with a concomitant reduction in air saturation, the degree of tailing present in the NP breakthrough curves (BTCs) reduced, and the mass of NPs recovered increased. Air saturation is positively correlated with the magnitude of air-water interfaces, which provide additional NP retention sites. At a lower injection flow rate, NP retention increased due to a longer residence time and comparatively high air saturation. NP transport behaviour was not sensitive to NP injection dose over the range tested. Increased retention and retardation of the NP BTC was observed in sediments with a higher clay and silt content. NPs coated with a lower concentration of a Pluronic block co-polymer to promote binding were preferentially retained within the crude oil zone. To simulate the asymmetrical NP breakthrough curves observed from the unsaturated systems required the use of a model that accounted for both mobile and immobile flow regions as well as NP attachment and detachment with nonlinear Langmuirian blocking. This model allowed examination of attachment and detachment rate coefficients which captured NP interaction with the porous medium and/or crude oil. It was found that the initial water saturation and flow rate did not have an appreciable impact on the NP attachment rate coefficient, while it increased by ~10× with increasing clay and silt content, and by ~100× in the presence of crude oil, indicating preferential NP attachment within the crude oil zone. As a result of the lower NP polymer concentration coating used to promote increased attachment to crude oil, higher retention was observed near the column inlet and was captured quantitatively by adding a depth-dependent straining term to the model. This retention behaviour represents a combination of irreversible attachment at the air-water interfaces and straining near the column inlet enhanced by the formation of NP aggregates. The detachment rate coefficient decreased with a lower initial water saturation and flowrate, but increased with higher clay and silt content. The findings from this study contribute to our understanding of the transport and binding behaviour of Pluronic-coated NPs in unsaturated conditions and, in particular, the role of initial water content, flowrate and porous medium texture. Demonstrated delivery of NPs to a target zone is an important step towards expanding the utility of NPs as treatment reagents.

Distinct interactions of pig and cow manure-derived colloids with TiO2 nanoparticles and their impact on stability and transport

The application of livestock manure and aquaculture wastewater into agricultural soil introduces animal manure-derived colloids into the environment. These manure-derived colloids generally contain different organic matter components and may facilitate nanoparticle transport to the subsurface. This study investigated the interaction between manure-derived colloids (cow and pig manures) and titanium dioxide (TiO₂) nanoparticles at neutral pH. The effect of this interaction on the stability, aggregation, and transport of TiO₂ in a saturated porous media was studied. Our study found that cow manure-derived colloids have many humic-like substances, and pig manure-derived colloids contain many protein components and some humic-like substances. The interactions of different manure-derived colloids with TiO₂ can affect the ζ-potential and aggregation status of TiO₂ in the aqueous system. The results showed that cow manure-derived colloids slightly increased the TiO₂ transport due to electrostatic repulsion, while pig manure-derived colloids substantially increased the TiO₂ mobility in porous media because of both electrostatic repulsion and steric hindrance. Since both animal manure and TiO₂ are ubiquitously present in the natural environment, manure-derived colloids can change the surface properties of TiO₂ and facilitate TiO₂ transport in the subsurface.

Nanoporous Metal Phosphonate Hybrid Materials as a Novel Platform for Emerging Applications: A Critical Review

Nanoporous metal phosphonates are propelling the rapid development of emerging energy storage, catalysis, environmental intervention, and biology, the performances of which touch many fundamental aspects of portable electronics, convenient transportation, and sustainable energy conversion systems. Recent years have witnessed tremendous research breakthroughs in these fields in terms of the fascinating pore properties, the structural periodicity, and versatile skeletons of porous metal phosphonates. This review presents recent milestones of porous metal phosphonate research, from the diversified synthesis strategies for controllable pore structures, to several important applications including adsorption and separation, energy conversion and storage, heterogeneous catalysis, membrane engineering, and biomaterials. Highlights of porous structure design for metal phosphonates are described throughout the review and the current challenges and perspectives for future research in this field are discussed at the end. The aim is to provide some guidance for the rational preparation of porous metal phosphonate materials and promote further applications to meet the urgent demands in emerging applications.

Spatiotemporal geo-electrical sensing of a Pluronic-coated cobalt ferrite nanoparticle slug in natural sand flow-through columns

Rising industrial interest in the application of nanomaterials for the remediation of contaminated sites has led to concern over the environmental fate of the nanoremediation agents used. A critical requirement in evaluating and understanding nanoparticle (NP) behaviour in porous media is the development of analytical methods capable of in situ monitoring of complex NP transport dynamics. Spectral induced polarization (SIP), a non-invasive geo-electrical technique, offers a promising tool for detecting and quantifying NPs in soil and aquifer media. However, its application for monitoring the spatial migration and attachment behaviour of NPs remains uninvestigated. Here, we present results from flow-through experiments where we monitored the transport of cobalt ferrite nanoparticles (CoFe-NPs) coated with Pluronic, an amphiphilic polymer, in natural aquifer sand columns. We coupled concentration breakthrough curve analysis with SIP monitoring and reactive transport modeling to relate spatiotemporal NP concentration distributions to geo-electrical signals. Changes in the real (σ') conductivity at three different locations along the columns closely correlated with model-computed total (solid plus aqueous phase) NP concentrations during the propagation of a NP slug. The imaginary conductivity (σ″) correlated closely with the arrival of the NP-slug. However, during the receding front, bimodal σ″-signal peak behaviour was observed propagating through the columns, indicating the existence of complex in situ NP transport dynamics, potentially revealing the rupture of nanoclusters upon straining and their effect on bulk charge storage that may not be obvious from breakthrough curve data alone. Fitting of a double Cole-Cole relaxation model yielded distinct shifts in relaxation time (τ) associated with the polarization of smaller length-scale particles. Post-NP pulse τ and σ″ did not return to pre-injection values; these lingering signals were caused by retained NP concentrations as low as 8.8 mg kg^-1. Our results support the applicability of SIP for spatial and temporal monitoring of NP distributions, with implications for the investigation of NP transport and nanoremediation strategies.

Co-transport of negatively charged nanoparticles in saturated porous media: Impacts of hydrophobicity and surface O-functional groups

Graphene oxide (GO) and polystyrene nanoplastic (PSNP) are typical carbonaceous nanomaterials which likely co-exist in soil and sediment. Here, we describe the transport of GO, irradiation reduced GO (RGO) and PSNP in saturated quartz sand both in single and binary systems. In the single transport system, the materials exhibited mobility in the order of GO > RGO > PSNP, due to increased hydrophobicity and decreased negative surface charges. Nevertheless, the co-transport of (R)GO and PSNP in the binary transport system was much more intricate. In Na⁺ saturated porous media, PSNP preferred to interact with (R)GO relative to the highly negatively charged quartz sand, thus (R)GO carried PSNP to break through the sand column. However, in Ca²⁺ saturated porous media, the transport of both (R)GO and PSNP was depressed, attributed to the particle-collector and particle-particle bridging effects between Ca²⁺ and the metal-complexing moieties of the nanoparticles and sand grains. Moreover, GO influenced the co-transport of PSNP to a larger extent than RGO, especially at relatively high ionic strength, because of the more abundant surface O-functional groups on GO providing more complexion sites with Ca²⁺. These results demonstrated that the transport of negatively charged nanomaterials was greatly related to the hydrophobicity and surface O-functional groups.

Too small to matter? Physicochemical transformation and toxicity of engineered nTiO2, nSiO2, nZnO, carbon nanotubes, and nAg

Engineered nanomaterials (ENMs) refer to a relatively novel class of materials that are increasingly prevalent in various consumer products and industrial applications - most notably for their superlative physicochemical properties when compared with conventional materials. However, consumer products inevitably degrade over the course of their lifetime, releasing ENMs into the environment. These ENMs undergo physicochemical transformations and subsequently accumulate in the environment, possibly leading to various toxic effects. As a result, a significant number of studies have focused on identifying the possible transformations and environmental risks of ENMs, with the objective of ensuring a safe and responsible application of ENMs in consumer products. This review aims to consolidate the results from previous studies related to each stage of the pathway of ENMs from being embodied in a product to disintegration/transformation in the environment. The scope of this work was defined to include the five most prevalent ENMs based on recent projected production market data, namely: nTiO₂, nSiO₂, nZnO, carbon nanotubes, and nAg. The review focuses on: (i) models developed to estimate environmental concentrations of ENMs; (ii) the possible physicochemical transformations; (iii) cytotoxicity and genotoxicity effects specific to each ENM selected; and (iv) a discussion to identify potential gaps in the studies conducted and recommend areas where further investigation is warranted.

Performance and mechanisms of sulfadiazine removal using persulfate activated by Fe3O4@CuOx hollow spheres

A Fe-Cu bimetal catalyst (FCHS) was synthesized by depositing Fe₃O₄ on the shell of CuO_x hollow spheres, which were prepared via a soft template method. Several characterization methods, including XRD, SEM-EDS&mapping, TEM, FTIR, and XPS, were used to reveal the morphology and surface properties of FCHS. The characterization results demonstrated that the double-shell hollow structure is formed with a dense coating of Fe₃O₄ nanoparticles on the surface of CuO_x hollow spheres. FCHS can exhibit excellent catalytic activity to degrade sulfadiazine (SDZ) with the oxidant of persulfate (PS). The optimal SDZ removal performance was explored by adjusting reaction parameters, including catalyst dosage, oxidant dosage, and solution pH. The SDZ removal efficiency in the FCHS + PS system could reach 95% at the optimal reaction condition ([catalyst]₀ = 0.2 g/L, [PS]₀ = 2 mM, pH = 7.0) with 5 mg/L of SDZ. Meanwhile, the degradation efficiency decreased with the coexistence of phosphate or carbonate anions. According to the results of radicals scavenging experiments and the electron paramagnetic resonance analysis, the radicals of SO₄·^-, O₂·^- and ·OH generated in the FCHS + PS system contribute to the degradation of SDZ. Moreover, the results of XPS revealed that the solid-state charge-transfer redox couple of Fe(III)/Fe(II) and Cu(I)/Cu(II) can promote the activation of PS. It means that the cooperation effect between Cu oxides and Fe oxides in the double-shell structure is beneficial to the catalytic degradation of SDZ. Furthermore, four possible pathways for SDZ degradation were proposed according to the analysis of intermediate products detected by the LCMS-IT-TOF.

Assessment on landfill liners as the barrier against C60 nanoparticles

Owing to the increasing usage of nanomaterials, it is imperative to assess their potential impacts on natural systems, and in particular, investigate if existing barriers can prevent nanomaterial emission in landfills because they will be disposed in landfills at the end of their useful lives. This study inspected the behavior of colloidal fullerene (nC₆₀) in and around landfill liner materials. Sorption isotherm experiments using either natural soil or high density polyethylene geomembrane as sorbents showed that nC₆₀ was readily removed by sorption to soil and precipitation, while there was no sorption to geomembrane. To investigate transport through soil, nC₆₀ was injected into columns of compacted soil layers with a thickness of 3.3-4.2 cm and hydraulic conductivity <1 × 10^-7 cm/s. The nanoparticles rarely passed through the layers owing to self-aggregation and/or screening by the soil layer. When they were detected in the effluent, breakthrough curves of an extraordinary shape were produced, which is presumably attributed to surface modification of collectors by deposited nC₆₀. However, simulation using the obtained mass transport parameters showed that it is unlikely that nC₆₀ from disposed C₆₀-containing products would overcome compacted clay liners; therefore, its migration to the ambient environment would be negligible.

Combined effect of physicochemical factors on the retention and transport of g-C3N4 in porous media

The environmental behaviors of graphitic carbon nitride (g-C₃N₄) have drawn increasing attention in recent. Understanding the fate and transport of g-C₃N₄ in porous media is necessary for evaluating its environmental risks. Column experiments were used in this study to investigate the combined effect of ionic strength (IS) and other common physicochemical factors (i.e. sand grain size, solution pH, and humic acid concentration) on g-C₃N₄ transport. The one-site kinetic models were applied to simulate the retention and transport of g-C₃N₄ in porous media, which fitted the breakthrough curves very well. Experimental and model results showed that g-C₃N₄ had a weak mobility with the transport mass recovery (TMR) less than 39.6% at pH 6.0 in absence of humic acid (HA). The mobility of g-C₃N₄ was inhibited with decreasing sand grain size, and the inhibited efficiency was enhanced with IS. However, g-C₃N₄ transport was significantly enhanced with increasing pH and HA concentration, and the enhanced efficiency was more obviously at high IS. The maximum TMR (78.3%) of g-C₃N₄ was observed with the presence of 5 mg L^-1 HA. These results indicated that physicochemical factors played an important and combined role in controlling g-C₃N₄ transport in porous media, which would lead to the more complex evaluation on the environmental behaviors of g-C₃N₄.

In-situ synthesis of metal nanoparticles@metal-organic frameworks: Highly effective catalytic performance and synergistic antimicrobial activity

M-NP@Zn-BIF (M-NP = Ag or Cu nanoparticle; Zn-BIF is a zinc-based boron imidazolate framework, Zn₂(BH(2-mim)₃)₂(obb); 2-mim = 2-methylimidazole; obb = 4,4'-oxybis(benzoate)) composites were successfully in-situ synthesized by utilizing the reducing ability of the BH bond contained in the Zn-BIF at room temperature without any additional chemical reduction reagents. These composites (225 μg/mL) exhibited excellent catalytic activity to convert 4-nitrophenol to 4-aminophenol in 2.5 min and 6 min with a conversion rate of 99.9 %, respectively. In addition, Ag@Zn-BIF (50 μg/mL) showed highly synergistic antibacterial activity against both Escherichia coli (E. coli) and Staphylococcus aureus (S. aureus) with a bactericidal rate of approximately 99.9 %. An antibacterial mechanism was proposed for the generation of intracellular reactive oxygen species (ROS) levels. Superoxide radicals (O^2-) and hydroxyl radicals (OH) formed during the antibacterial process were shown to accelerate the death of bacteria. They also exhibited highly photocatalytic activity for Rhodamine B (RhB). When the concentration of the composites is 1000 μg/mL, the photocatalytic efficiency of Ag@Zn-BIF and Cu@Zn-BIF increased by 31.62 and 18.13 times compared with Zn-BIF, respectively. All in all, this study developed a simple and versatile integrated platform for the removal of nitrophenols, organic dyes, and the effective inactivation of bacteria in water.

Amino-functionalized graphene oxide for Cr(VI), Cu(II), Pb(II) and Cd(II) removal from industrial wastewater

Amino-functionalized graphene oxide (GO-NH2) was synthesized by grafting (3-aminopropyl) triethoxysilane on the graphene oxide (GO) surface. The GO-NH2 with high surface area and numerous active sites can efficiently adsorb Cr(VI), Cu(II), Pb(II) and Cd(II) ions. The maximum adsorption capacities of GO-NH2 for Cr(VI), Cu(II), Pb(II) and Cd(II) were 280.11, 26.25, 71.89 and 10.04 mg g−1, respectively. The pseudo-first-order and pseudo-second-order kinetic models were employed to describe the kinetic processes. The experimental data agreed well with the pseudo-second-order kinetic equation, and the adsorption of heavy metals onto GO-NH2 occurs via chemical adsorption. The characteristics of Cr(VI), Cu(II), Pb(II) and Cd(II) in the GO-NH2 adsorption processes were analyzed using the Langmuir and Freundlich isotherm models. The adsorption processes of Pb(II) and Cd(II) on GO-NH2 were fit by the Langmuir model. The Freundlich isotherm model was well correlated to Cr(VI) and Cu(II). The GO-NH2 is a promising material for the removal of heavy metal ions from industrial wastewater. This study provides an effective pathway to process industrial wastewater, and the GO-NH2 has a good adsorption effect for the treatment of heavy metals in industrial wastewater.

The role of Fe oxyhydroxide coating, illite clay, and peat moss in nanoscale titanium dioxide (nTiO2) retention and transport in geochemically heterogeneous media

Natural media such as soil and sediment contain mineralogical and organic components with distinct chemical, surface, and electrostatic properties. To better understand the role of various soil and sediment components on particle transport, columns were packed with quartz sand and natural sediment with added Fe oxyhydroxide coating, illite clay, and peat moss to investigate how these added components influence nTiO₂ retention and transport in geochemically heterogeneous medium. Results showed that nTiO₂ transport was low at pH 5, attributable to the electrostatic attraction between positively-charged nTiO₂ and negatively-charged medium. While illite did not notably affect nTiO₂ transport at pH 5, Fe oxyhydroxide coating increased nTiO₂ transport due to electrostatic repulsion between Fe oxyhydroxide and nTiO₂. Peat moss also increased nTiO₂ transport at pH 5, attributable to the increased DOC concentration, which resulted in higher DOC adsorption to nTiO₂ and intensified electrostatic repulsion between nTiO₂ and the medium. At pH 9, nTiO₂ transport was high due to the electrostatic repulsion between negatively-charged nTiO₂ and medium surfaces. Fe oxyhydroxide coating at pH 9 slightly delayed nTiO₂ transport due to electrostatic attraction, while illite clay and peat moss substantially inhibited nTiO₂ transport via straining/entrapment or electrostatic attraction. Overall, this study demonstrated that pH has a considerable effect on how minerals and organic components of a medium influence nTiO₂ transport. At low pH, electrostatic attraction was the dominant mechanism, therefore, nTiO₂ mobility was low regardless of the differences in mineralogical and organic components. Conversely, nTiO₂ mobility was high at high pH and nTiO₂ retention was dominated by straining/entrapment and sensitive to the mineralogical and organic composition of the medium.

Facile Synthesis and Reuse of Magnetic Black Carbon Magnetite (BC-Mag) for Fast Carbamazepine Removal from Water

Magnetic carbonaceous nanomaterials are needed in water treatment applications because they can offer both carbon surfaces for sorption of organic pollutants and ease of material magnetic retrieval for regeneration and reuse. In this study, we employed a facile one-step method to synthesize a black carbon-magnetite composite (BC-Mag) by high-temperature annealing of black carbon and hematite. The nanocomposite was easily dispersed and stable in water owing to the presence of negatively charged oxygen surface functional groups. Sorption kinetics with dissolved carbamazepine showed a rapid initial uptake with equilibrium achieved within only minutes. The sorption extent can be described with the Freundlich model, and surface area normalized sorption affinity was an order of magnitude greater than conventional granular activated carbon. The sorption extent of neutral carbamazepine remained constant between pH 2–10 while surface zeta potential decreased. BC-Mag can be reused for the sorption of carbamazepine up to six times without significant loss of the sorption extent.

Enhanced adsorption of bisphenol A and sulfamethoxazole by a novel magnetic CuZnFe2O4-biochar composite

The widespread occurrence of endocrine-disrupting compound and pharmaceutical active compounds such as bisphenol A (BPA) and sulfamethoxazole (SMX) in natural freshwater resources can cause serious environmental problems even at low exposure levels. In this work, in order to remove BPA and SMX from aqueous solutions, a novel biochar-supported magnetic CuZnFe₂O₄ composite (CZF-biochar) was synthesized by a facile one-pot hydrothermal process. After characterization studies, the key factors affecting BPA and SMX adsorption on CZF-biochar were comprehensively investigated. The primary mechanisms for BPA and SMX adsorption included charge-assisted H-bonding, hydrophobic, and π-π electron donor-acceptor interactions. In summary, considering the fast kinetics, high adsorption properties, easy magnetic separation, and recyclability for multiple reuses, the CZF-biochar composite has potential for the removal of BPA, SMX, and potentially other emerging organic contaminants from contaminated soil and water.

Different modelling approaches for predicting titanium dioxide nanoparticles mobility in intact soil media

Understanding the transport behaviour of new and emerging materials such as engineered nanoparticles (ENPs) is vital for the accurate assessment of their functionality and fate in environmental systems. Predicting ENP mobility in soil systems based on common attributes of either soil or ENPs is of significant interest as an alternative to conducting laborious and time consuming column experiments. Thus this study investigates the importance of different soil properties and experimental conditions on titanium dioxide nanoparticles (nTiO₂) mobility in real soil media and also evaluates four different modelling approaches including Multiple Linear Regression (MLR), Classification and Regression Tree (CART), Random Forest (RF) and Artificial Neural Network (ANN) for predicting nTiO₂ mobility in soil media. The performance of both ANN and RF models were good for predicting nTiO₂ transport in soil media, with ANN predictions being slightly superior to RF with less generalization errors. However, RF had the advantage of requiring less input predictors. In comparison the MLR model exhibited poor performance in both calibration and validation datasets, and while the validity of CART was almost acceptable in the calibration dataset, its efficiency was poor for the validation dataset. In addition to soil solution chemistry and hydraulic properties, other important factors having a major contribution to nTiO₂ transport through soil included soil fracture associated properties and the existence of preferential flows.

Impacts of leachate of landfill on the groundwater hydrochemistry and size distributions and heavy metal components of colloids: a case study in NE China

Colloids associated with heavy metals are ubiquitous in contaminated groundwater; waste accumulation at imperfectly sealed landfills can produce large amounts of leachate with colloids and heavy metal contaminants, which can pollute the downstream groundwater. In this study, three sites in a landfill were sampled to reveal heavy metal particle size distributions and their chemical compositions. The > 220 nm particle sizes were the predominant size in the downstream groundwater, while the < 10 nm particle sizes were the predominant size in the upstream groundwater. Total Fe increased from 35.5 μg/L in the upstream groundwater to 107 μg/L in the downstream groundwater. This increase was attributed to the enhanced migration and accumulation of colloids in the aqueous phase. The elements and the colloid size distribution in the landfill indirectly reflected the composition and degradation of the waste. Colloids played a key role in distribution of both solid particles and aqueous contaminants in the landfill. The results of this study will contribute to the knowledge of the effect of different contaminants in the vicinity of landfills without appropriate sealing systems.

Evaluation of the colloidal stability and adsorption performance of reduced graphene oxide-elemental silver/magnetite nanohybrids for selected toxic heavy metals in aqueous solutions

Reduced graphene oxide (rGO) hybridized with magnetite and/or elemental silver (rGO/magnetite, rGO/silver, and rGO/magnetite/silver) nanoparticles were evaluated as potential adsorbents for toxic heavy metal ions (Cd (II), Ni(II), Zn(II), Co(II), Pb(II), and Cu(II)). Although the deposition of iron oxide and silver nanoparticles on the rGO nanosheets played an inhibitory role in metal ion adsorption, the metal adsorption efficiency by the nanohybrids (NHs) was still higher than that reported for many other sorbents (e.g., activated biochar, commercial resins, and nanosized hydrated Zr(IV) oxide particles). X-ray photoelectron spectroscopy analyses revealed that complexation with deprotonated adsorbents and cation exchange was an important mechanism for Cd(II) ion removal by the rGO and NHs. Competitive adsorption tests using multi metals showed that the adsorption affinity of metal ions on the rGO and its NHs follows the order (Cu(II), Zn(II)) > Ni(II) > Co(II) > (Pb(II), Cd(II)), which is similar to the order observed for single-metal adsorption experiments. These results can be explained by the destabilization abilities of the rGO and NHs, as well as the ionic radii of the considered metal ions. Our findings demonstrate the feasibility of using rGO-based NHs as highly efficient adsorbents for heavy metal removal from water.

Modeling the Transport of the "New-Horizon" Reduced Graphene Oxide-Metal Oxide Nanohybrids in Water-Saturated Porous Media

Little is known about the fate and transport of the "new-horizon" multifunctional nanohybrids in the environment. Saturated sand-packed column experiments ( n = 66) were therefore performed to investigate the transport and retention of reduced graphene oxide (RGO)-metal oxide (Fe3O4, TiO2, and ZnO) nanohybrids under environmentally relevant conditions (mono- and divalent electrolytes and natural organic matter). Classical colloid science principles (Derjaguin-Landau-Verwey-Overbeek (DLVO) theory and colloid filtration theory (CFT)) and mathematical models based on the one-dimensional convection-dispersion equation were employed to describe and predict the mobility of RGO-Fe3O4, RGO-TiO2, and RGO-ZnO nanohybrids in porous media. Results indicate that the mobility of the three nanohybrids under varying experimental conditions is overall explainable by DLVO theory and CFT. Numerical simulations suggest that the one-site kinetic retention model (OSKRM) considering both time- and depth-dependent retention accurately approximated the breakthrough curves (BTCs) and retention profiles (RPs) of the nanohybrids concurrently; whereas, others (e.g., two-site retention model) failed to capture the BTCs and/or RPs. This is primarily because blocking BTCs and exponential/hyperexponential/uniform RPs occurred, which is within the framework of OSKRM featuring time- (for kinetic Langmuirian blocking) and depth-dependent (for exponential/hyperexponential/uniform) retention kinetics. Employing fitted parameters (maximum solid-phase retention capacity: Smax = 0.0406-3.06 cm3/g; and first-order attachment rate coefficient: ka = 0.133-20.6 min-1) extracted from the OSKRM and environmentally representative physical variables (flow velocity (0.00441-4.41 cm/min), porosity (0.24-0.54), and grain size (210-810 μm)) as initial input conditions, the long-distance transport scenarios (in 500 cm long sand columns) of the three nanohybrids were predicted via forward simulation. Our findings address the existing knowledge gap regarding the impact of physicochemical factors on the transport of the next-generation, multifunctional RGO-metal oxide nanohybrids in the subsurface.

Considerations for Safe Innovation: The Case of Graphene

The terms "Safe innovation" and "Safe(r)-by-design" are currently popular in the field of nanotechnology. These terms are used to describe approaches that advocate the consideration of safety aspects already at an early stage of the innovation process of (nano)materials and nanoenabled products. Here, we investigate the possibilities of considering safety aspects during various stages of the innovation process of graphene, outlining what information is already available for assessing potential hazard, exposure, and risks. In addition, we recommend further steps to be taken by various stakeholders to promote the safe production and safe use of graphene.

Effects of temperature on graphene oxide deposition and transport in saturated porous media

Laboratory batch sorption and sand column experiments were conducted to examine the effects of temperature (6 and 24°C) on the retention and transport of GO in water-saturated porous media with different combination of solution ionic strength (IS, 1 and 10mM), sand type (natural and acid-cleaned), and grain size (coarse and fine). Although results from batch sorption experiment showed that temperature affected the sorption of GO onto the sand grains at the low IS, the interactions between GO and the sand were relatively weak, which did make the temperature effect prominent. When the IS was 1mM, experimental temperature showed little effect on GO retention and transport regardless of the medium properties. GO was highly mobile in the sand columns with mass recovery rates ranged from 77.3% to 92.4%. When the IS increased to 10mM, temperature showed notable effects on GO retention and transport in saturated porous media. For all the combinations of sand type and grain size, the higher the temperature was, the less mobile GO particles were. The effects of temperature on GO retention and transport in saturated porous media were further verified though simulations from an advection-dispersion-reaction model.

Antibacterial properties and toxicity from metallic nanomaterials

The era of antibiotic resistance is a cause of increasing concern as bacteria continue to develop adaptive countermeasures against current antibiotics at an alarming rate. In recent years, studies have reported nanoparticles as a promising alternative to antibacterial reagents because of their exhibited antibacterial activity in several biomedical applications, including drug and gene delivery, tissue engineering, and imaging. Moreover, nanomaterial research has led to reports of a possible relationship between the morphological characteristics of a nanomaterial and the magnitude of its delivered toxicity. However, conventional synthesis of nanoparticles requires harsh chemicals and costly energy consumption. Additionally, the exact relationship between toxicity and morphology of nanomaterials has not been well established. Here, we review the recent advancements in synthesis techniques for silver, gold, copper, titanium, zinc oxide, and magnesium oxide nanomaterials and composites, with a focus on the toxicity exhibited by nanomaterials of multidimensions. This article highlights the benefits of selecting each material or metal-based composite for certain applications while also addressing possible setbacks and the toxic effects of the nanomaterials on the environment.

Assessing the Risk of Engineered Nanomaterials in the Environment: Development and Application of the nanoFate Model

We developed a dynamic multimedia fate and transport model (nanoFate) to predict the time-dependent accumulation of metallic engineered nanomaterials (ENMs) across environmental media. nanoFate considers a wider range of processes and environmental subcompartments than most previous models and considers ENM releases to compartments (e.g., urban, agriculture) in a manner that reflects their different patterns of use and disposal. As an example, we simulated ten years of release of nano CeO₂, CuO, TiO₂, and ZnO in the San Francisco Bay area. Results show that even soluble metal oxide ENMs may accumulate as nanoparticles in the environment in sufficient concentrations to exceed the minimum toxic threshold in freshwater and some soils, though this is more likely with high-production ENMs such as TiO₂ and ZnO. Fluctuations in weather and release scenario may lead to circumstances where predicted ENM concentrations approach acute toxic concentrations. The fate of these ENMs is to mostly remain either aggregated or dissolved in agricultural lands receiving biosolids and in freshwater or marine sediments. Comparison to previous studies indicates the importance of some key model aspects including climatic and temporal variations, how ENMs may be released into the environment, and the effect of compartment composition on predicted concentrations.

Valorisation of post-sorption materials: Opportunities, strategies, and challenges

Adsorption is a facile, economic, eco-friendly and low-energy requiring technology that aims to separate diverse compounds (ions and molecules) from one phase to another using a wide variety of adsorbent materials. To date, this technology has been used most often for removal/recovery of pollutants from aqueous solutions; however, emerging post-sorption technologies are now enabling the manufacture of value-added key adsorption products that can subsequently be used for (i) fertilizers, (ii) catalysis, (iii) carbonaceous metal nanoparticle synthesis, (iv) feed additives, and (v) biologically active compounds. These new strategies ensure the sustainable valorisation of post-sorption materials as an economically viable alternative to the engineering of other green chemical products because of the ecological affability, biocompatibility, and widespread accessibility of post-sorption materials. Fertilizers and feed additives manufactured using sorption technology contain elements such as N, P, Cu, Mn, and Zn, which improve soil fertility and provide essential nutrients to animals and humans. This green and effective approach to managing post-sorption materials is an important step in reaching the global goals of sustainability and healthy human nutrition. Post-sorbents have also been utilized for the harvesting of metal nanoparticles via modern catalytic pyrolysis techniques. The resulting materials exhibited a high surface area (>1000m²/g) and are further used as catalysts and adsorbents. Together with the above possibilities, energy production from post-sorbents is under exploration. Many of the vital 3E (energy, environment, and economy) problems can be addressed using post-sorption materials. In this review, we summarize a new generation of applications of post-adsorbents as value-added green chemical products. At the end of each section, scientific challenges, further opportunities, and issues related to toxicity are discussed. We believe this critical evaluation not only delivers essential contextual information to researchers in the field but also stimulates new ideas and applications to further advance post-sorbent applications.

Toxicity of graphene oxide to white moss Leucobryum glaucum

Graphene oxide was toxic to white moss Leucobryum glaucum.

Novel nanofiber yarns synchronously endued with tri-functional performance of superparamagnetism, electrical conductivity and enhanced fluorescence prepared by conjugate electrospinning

[Fe₃O₄/PANI/PAN]//[Eu(BA)₃phen/PAN] heterogeneous nanofiber yarns were fabricated via electrospinning, and the yarns synchronously possess trifunctionality of superparamagnetism, electrical conductivity and enhanced fluorescence.

Review of key factors controlling engineered nanoparticle transport in porous media

Nanotechnology, an emerging technology, has witnessed rapid development in production and application. Engineered nanomaterials revolutionize the industry due to their unique structure and superior performance. The release of engineered nanoparticles (ENPs) into the environment, however, may pose risks to the environment and public health. To advance current understanding of environmental behaviors of ENPs, this work provides an introductory overview of ENP fate and transport in porous media. It systematically reviews the key factors controlling their fate and transport in porous media. It first provides a brief overview of common ENPs in the environment and their sources. The key factors that govern ENP transport in porous media are then categorized into three groups: (1) nature of ENPs affecting their transport in porous media, (2) nature of porous media affecting ENP transport, and (3) nature of flow affecting ENP transport in porous media. In each group, findings in recent literature on the specific governing factors of ENP transport in porous media are discussed in details. Finally, this work concludes with remarks on the importance of ENP transport in porous media and directions for future research.

Modeling the effects of surfactant, hardness, and natural organic matter on deposition and mobility of silver nanoparticles in saturated porous media

This study aims to provide insights into the mechanisms governing the deposition and retention of silver nanoparticles (AgNPs) in saturated porous media. Column experiments were conducted with quartz sand under saturated conditions to investigate the deposition kinetics of AgNPs, their mobility at different groundwater hardnesses (10-400 mg/L as CaCO3), and humic acid (HA, 0-50 mg/L as dissolved organic carbon [DOC]). An anionic surfactant, sodium dodecyl sulfate (SDS), was used as a dispersing agent to prepare a SDS-AgNPs suspension. The deposition kinetics of AgNPs were highly sensitive to the surfactant concentration, ionic strength, and cation type in solution. The breakthrough curves (BTCs) of SDS-AgNPs suggested that the transport and retention were influenced by groundwater hardness and HA. At low water hardness and high HA, high mobility of SDS-AgNPs was observed in saturated conditions. However, the retention of SDS-AgNPs increased substantially in very hard water with a low concentration of HA, because of a decreased primary energy barrier and the straining effect during the course of transport experiments. A modified clean-bed filtration theory and a two-site kinetic attachment model showed good fits with the BTCs of SDS-AgNPs. The fitted model parameters (katt and kstr) could be used successfully to describe that the retention behaviors were dominated by electrostatic and electrosteric repulsion, based on extended Derjaguin-Landau-Vaerwey-Overbeek calculations.