Adsorption of diclofenac onto organoclays: Effects of surfactant and environmental (pH and temperature) conditions

H*ads dynamics engineering via bimetallic Pd-Cu@MXene catalyst for enhanced electrocatalytic hydrodechlorination

Electrocatalytic hydrodechlorination (EHDC) is a promising approach to safely remove halogenated emerging contaminants (HECs) pollutants. However, sluggish production dynamics of adsorbed atomic H (H*ads) limit the applicability of this green process. In this study, bimetallic Pd-Cu@MXene catalysts were synthesized to achieve highly efficient removal of HECs. The alloy electrode (Pd-Cu@MX/CC) exhibited better EHDC performance in comparison to Pd@MX/CC electrode, resulting in diclofenac degradation efficiency of 93.3 ± 0.1%. The characterization analysis revealed that the Pd0/PdII ratio decreased by forming bimetallic Pd-Cu alloy. Density functional theory calculations further demonstrated the electronic configuration modulation of the Pd-Cu@MXene catalysts, optimizing binging energies for H* and thereby facilitating H*ads production and tuning the reduction capability of H*ads. Noteably, the amounts and reduction potential of H*ads for Pd-Cu@MXene catalysts were 1.5 times higher and 0.37 eV lower than those observed for the mono Pd electrode. Hence, the introduction of Cu into the Pd catalyst optimized the dynamics of H*ads production, thereby conferring significant advantages to EHDC reactions. This augmentation was underscored by the successful application of the alloy catalysts supported by MXene in EHDC experiments involving other HECs, which represented a new paradigm for EHDC for efficient recalcitrant pollutant removal by H*ads.

Engineered Clay-Polymer Composite for Biomedical Drug Delivery and Future Challenges: A Survey

Clay materials are widely used in drug delivery systems due to their unique characteristics. Montmorillonite is a major component of bentonite and it has a large surface area, better swelling capacity, and high adsorption capacity. The modification of natural bentonite could improve its sorption ability for new emerging applications. Recent advancements in the polymer-silicate composite have novel biomedical applications in drug delivery, tissue regeneration, wound healing, cancer therapy, enzyme immobilization, diagnostic and therapeutic devices, etc. Perspective view of the montmorillonite- polymer composite as a pharmaceutical carrier in drug delivery systems has been discussed in this review. Different types of modification of montmorillonite for the development of pharmaceutical formulations have also been documented. Many challenges in clay nanocomposite systems of polymer of natural/synthetic origin are yet to be explored in improving antimicrobial properties, mechanical strength, stimuli responsiveness, resistance to hydrolysis, etc. Drug interaction and binding capability, swelling of clay may be carried out for finding possible applications in monitoring delivery systems. Pharmaceutical properties of active drugs in the formulation could also be improved along with dissolution rate, solubility, and adsorption. The clay-incorporated polymeric drug delivery systems may be examined for a possible increase in swelling capacity and residence time after mucosal administration.

NiFe-PANI composites synthesized by electrodeposition for enhanced photocatalytic degradation of diclofenac sodium from wastewater

A simple inexpensive approach was used to synthesize NiFe-PANI nanocomposites and used for photodegradation of diclofenac sodium (DCF) in water sources. Morphological, optical, structural, and catalytic properties of the nanocomposites were investigated using X-ray diffraction (XRD) to confirm the cubic structure of NiFe nanoparticles and Fourier-transform infrared spectroscopy (FTIR) that revealed the presence of NiFe and PANI, scanning electron microscopy (SEM) showed the uniform distribution of NiFe nanoparticles onto the surface of PANI, Energy-Dispersive X-ray spectroscopy (EDX) was utilized to validate the composition of the obtained Permalloy NiFe-PANI nanocomposites, optical properties confirmed the decrease of Eg band gap from 2.62 to 2.51 eV by the addition of NiFe. The NiFe-PANI composite showed superior photocatalytic efficiency in degrading DCF, achieving 82.53% degradation in 15 min and 97.89% in 60 min. This was significantly higher than the PANI alone, which achieved 62.72 and 93.48% degradation in the same time intervals respectively. The results indicated that the photocatalytic efficiency remained consistent, with no observable decrease, even after five cycles of recycling. The NiFe-PANI catalyst served as an efficient and cost-effective photocatalyst for DCF degradation, and the study holds promise for the photocatalytic removal of other organic pollutants from water and wastewater.

Modular Toolbox as Snap Jewelry for Biomimetic Synthesis of Multifunctional Amino Acid Surfactants Inspired by Melanin

Amino acid surfactants have gained significant importance in overcoming the limitations of conventional surfactants, notably, their low biocompatibility and biodegradability. However, the current amino acid surfactants lack multifunctional properties due to the nonreactivity of their aliphatic chains, necessitating the development of a new type of amino acid surfactant. A novel melanin-like amino acid surfactant and a biomimetic synthesis route were devised by mimicking the biosynthesis of melanin. Renewable natural polyphenol compounds with catechol moieties were utilized as building blocks for the hydrophobic group. In a proof-of-concept experiment, ethyl protocatechuate was oxidized to o-quinone and subsequently covalently linked to the amino group of lysine via Michael addition. The chemical structure was verified using liquid chromatography-tandem mass spectroscopy. The melanin-like amino acid surfactant exhibited excellent surface-active properties, with a critical micelle concentration of 1.59 mN m-1. Furthermore, it demonstrated remarkable emulsifying, foaming, solubilizing, dispersing, and wetting capabilities. Notably, it also possessed multifunctionality, including antibacterial activity, antioxidant activity, robustness, and mildness. These outstanding properties indicate significant potential for various applications. This strategy offers innovative insights and a versatile, modular toolbox for synthesizing multifunctional amino acid surfactants that mimic melanin. The approach allows for the easy interchange of o-quinone building blocks, which is akin to snap jewelry.

Preparation and evaluation of a coated smectite clay-based material modified with epichlorohydrin-dimethylamine for the diclofenac removal

This study reports the analysis of diclofenac removal from aqueous solution using a novel adsorbent coating with amphoteric surface. This adsorbent coating was improved using a new amphoteric ratio to increase its performance for the removal of pharmaceuticals such as diclofenac. The adsorbent coating was formulated using acrylic polymer emulsion, smectite-based clay powder and epichlorohydrin-dimethylamine to obtain a layer form via the implementation of a facile synthesis method. In a previous study, this adsorbent coating was successful to remove cationic and anionic dyes. Therefore, this research aimed to further investigate and test its application in the removal of other emerging water pollutants like pharmaceuticals. SEM, EDX, and FTIR analyses were carried out for the characterization of this novel adsorbent. The effects of adsorbent composition, diclofenac concentration, temperature, and solution pH were studied and modeled. The best conditions to improve the diclofenac adsorption was 303 K and pH 3 where the adsorption capacity was 25.59 mg/g. Adsorption isotherms and kinetics were quantified and modeled, and the corresponding adsorption mechanism was also analyzed. Diclofenac adsorption with this novel material was exothermic and spontaneous. This alternative adsorbent is promising for diclofenac removal from industrial wastewater systems.

Selective Adsorption of Organic Micro-Pollutants by Smectite Clays Revealed from Atomistic Simulations

In this study, atomistic simulations were carried out to study the difference in the adsorption process between two similar molecules, diazepam and oxazepam, on Na+-montmorillonite. Kinetic and XRD measurements showed a contrasting adsorption mechanism of these two molecules, differing only by the presence/absence of methyl and hydroxyl groups, with a larger adsorption amount and intercalation for the oxazepam. The structural characterization of these molecules was investigated through DFT calculations and showed the vicinity of hydroxyl and carbonyl groups for only the chair conformation of oxazepam compared to the boat conformation. Classical molecular dynamics simulations of diazepam and the two forms of oxazepam on the external surface of Na+-montmorillonite highlighted the better coordination of the oxazepam-chair conformation, compared to its boat counterpart and diazepam. This has been confirmed through DFT calculations, from which a coordination energy that is greater by 10 kcal·mol-1 is observed. This strongly suggests that the experimentally observed intercalation of oxazepam occurs only in the chair form because of the strong coordination with the Na+ cation present in the Na-Mt interlayer. Classical MD simulations of the intercalated oxazepam chair molecule in the Na-Mt interlayer allowed the evaluation of the interlayer spacing d001, which was in very good agreement with the experimental XRD measurement.

Investigation of herbicide sorption-desorption using pristine and organoclays to explore the potential carriers for controlled release formulation

Injudicious application of available commercial herbicide formulations leads to water, air and soil contamination, which adversely affect the environment, ecosystems and living organisms. Controlled release formulation (CRFs) could be an effective way to reduce the problems associated with commercially available herbicides. Organo-montmorillonites are prominent carrier materials for synthesising CRFs of commercial herbicides. Quaternary amine and organosilane functionalised organo-montmorillonite and pristine montmorillonite were used to investigate their potential as suitable carriers for CRFs in herbicide delivery systems. The experiment involved a batch adsorption process with successive dilution method. Results revealed that pristine montmorillonite is not a suitable carrier for CRFs of 2,4-D due to its low adsorption capacity and hydrophilic nature. Conversely, octadecylamine (ODA) and ODA-aminopropyltriethoxysilane (APTES) functionalised montmorillonite has better adsorption capacities. Adsorption of 2,4-D onto both organoclays is higher at pH.3 (232.58% for MMT1 and 161.29% for MMT2) compared to higher pH until pH.7 (49.75% for MMT1 and 68.49% for MMT2). Integrated structural characterisation studies confirmed the presence of 2,4-D on the layered organoclays. The Freundlich adsorption isotherm model fitted best to the experimental data, which revealed an energetically heterogeneous surface of the experimental organoclays, and adsorption which specifically involved chemisorption. The cumulative desorption percentages of adsorbed 2,4-D from MMT1_{(2,4-D loaded)} and MMT2_{(2,4-D loaded)} after seven desorption cycles were 65.53% and 51.45%, respectively. This outcome indicates: firstly, both organoclays are potential carrier materials for CRFs of 2,4-D; secondly, they have the ability to reduce the instantaneous release of 2,4-D immediately after application; and thirdly, eco-toxicity is greatly diminished.

Super-adsorbent microspheres based on a triallyl isocyanurate-maleic anhydride copolymer for the removal of organic pollutants from water

Owing to the frequent occurrence of diclofenac sodium (DS) in fresh aquatic environments and its potential toxicity towards living organisms, the effective removal of DS has attracted worldwide attention. Herein, a green and efficient strategy to fabricate crosslinked microspheres with interconnected mesoporous structures and abundant adsorption active sites was developed. With this strategy, triallyl isocyanurate (TAIC)-maleic anhydride (MAH) copolymer microspheres (TMs) with a diameter of 1.19-1.35 μm were first prepared by self-stabilized precipitation (2SP) polymerization, and the TMs possess a large amount reactive anhydride groups (62.5-71.8 mol%), a specific surface area of 51.6-182.4 m² g^-1 and a mesoporous structure (average pore size: 3.4-3.8 nm). Then the TMs were further functionalized with polyethylenimine (PEI) to give rise to cationic microspheres (Cat-TMs), which showed excellent adsorption performance to DS with a rapid adsorption rate (reached equilibrium within 30 min), a very high equilibrium adsorption capacity (1421 mg g^-1) and excellent recyclability. The pseudo-second-order model and Langmuir model were a good fit for the adsorption kinetic and isotherm process, respectively. Furthermore, due to the high cation density (4.291 mmol g^-1) and excellent pH buffer capacity of Cat-TMs, the adsorption capacity can be maintained at a high level within the pH range of 6-10. The regenerated Cat-TMs showed only a slight loss (<5%) in the adsorption capacity even after 5 adsorption-desorption cycles. In short, Cat-TMs can be considered as a highly promising adsorbent for the rapid and ultra-efficient removal of anionic organic contaminants and have significant potential to be applied in wastewater treatment.

Regulating defective sites for pharmaceuticals selective removal: Structure-dependent adsorption over continuously tunable pores

Developing efficient adsorbents with proper pore size for pharmaceutical removal is challenging. Water stable metal-organic frameworks (MOFs) are crystalline materials within the three-dimensional frameworks, which have already aroused increasing attention for their potential advantages with high surface area and abundant channels. However, whether or not the existing ones are performing their full capacities needs to be seriously considered. Herein, we precisely designed a series of fine-tuning hierarchically porous materials based on the water-stable Zr-based MOFs. The adsorption capacity and uptake rate of as-synthesized materials for pharmaceuticals are significantly improved. Fifteen isostructural frameworks with increasing finely tuned pore structures were successfully constructed with seven monocarboxylic modulators of increasing alkyl chain lengths. A strong correlated relationship between the mesoporous proportion and trapping kinetics can be found. Adsorption performance of 17 pharmaceuticals with various typical categories has been systematically studied over these as-synthesized materials. Competitors in natural wastewater were studied systematically. The competitive adsorption can selectively trap the target compounds in HA (humic acid), BSA (bovine serum albumin), and BHB (bovine hemoglobin) by an efficient size exclusion effect. Thus, this study offers helpful guidance for MOF modification to enhance the removal of micropollutants in natural wastewater and a fundamental understanding of the porosity-performance relationships.

Influence of the Type and the Amount of Surfactant in Phillipsite on Adsorption of Diclofenac Sodium

Modified phillipsite samples were prepared with two different amounts (monolayer and bilayer coverage) of surfactants octadecyldimethylbenzylammonium chloride (O) and dodecylamine (D). Composites were characterized by Fourier transform infrared spectroscopy with attenuated total reflectance (FTIR–ATR), thermal analysis and determination of zeta potential, and subsequently tested for removal of diclofenac sodium (DCF). Drug adsorption experiments were performed under different initial DCF concentrations and different contact times. In order to investigate the influence of the chemical structure of surfactants used for modification of phillipsite on the preparation and properties of composites and DCF adsorption, experimental data were compared with previously published results on DCF adsorption by composites containing phillipsite and the same amounts of surfactants cetylpyridinium chloride (C) and Arquad®2HT-75 (A). DCF adsorption isotherms for O and D composites showed a better fit with the Langmuir model with maximum adsorption capacities between 12.3 and 38.4 mg/g and are similar to those for C and A composites, while kinetics run followed a pseudo-second-order model. Composites containing either benzyl or pyridine functional groups showed higher adsorption of DCF, implying that surfactant structure has a significant impact on drug adsorption. Drug adsorption onto O, D, C and A composites was also confirmed by FTIR–ATR spectroscopy and zeta potential measurements.

Efficient removal of glyphosate from aqueous solutions by adsorption on Mg-Al-layered double oxides: thermodynamic, kinetic, and mechanistic investigation

Up to 90% of glyphosate was removed in 40 min by a 2:1 Mg2Al-layered double oxide (LDO) at pH 10, and the adsorption kinetics fitted a pseudo-second-order law. The adsorption isotherms were type L, and the Langmuir model best fitted the experimental data, with qmax of 158.22 μg/mg at 25 °C. The intraparticle diffusion model suggested that the adsorption process is dependent on the thickness and formation of the film at the solution/solid interface. The XRD results excluded the intercalation of glyphosate anions, and FTIR along with solid-state 13C and 31P MAS NMR confirmed that the glyphosate anions interact through the carboxylate and/or phosphonate moieties, both in end-on and side-on modes to the LDO surface. Glyphosate removal was also investigated in the presence of different anionic species, and simultaneous adsorption showed that carbonate and phosphate ions strongly influence glyphosate removal.

Diclofenac removal by the microalgae species Chlorella vulgaris, Nannochloropsis oculata, Scenedesmus acutus, and Scenedesmus obliquus

In this work, we evaluated the removal efficiency of diclofenac by Chlorella vulgaris OW-01, Nannochloropsis oculata CCAP 849/7, Scenedesmus acutus UTEX 72, and Scenedesmus obliquus CCAP 276/2. Each microalga was grown in media with different concentrations (50 and 100% of the original formulation) of carbon, nitrogen, and phosphorus, to evaluate their effect on the removal of diclofenac. We also evaluated the photodegradation of diclofenac under the same conditions. The diclofenac removed from the media ranged from 59 to 92%, obtaining the highest removal with S. obliquus. The diclofenac adsorbed on the cell walls ranged from 12.2 to 26.5%, obtaining the highest adsorption with S. obliquus. The diclofenac degraded by light ranged from 15 to 28%. The nutrient deficit showed no influence on the removal of diclofenac in any of the microalgae under study. These results indicate that S. obliquus is the best alternative for the bioremediation of diclofenac.

Supplementary Information

The online version contains supplementary material available at 10.1007/s13205-022-03268-2.

Adsorption of Non-Steroidal Anti-Inflammatory Drugs on Alginate-Carbon Composites-Equilibrium and Kinetics

In this work, alginate-carbon composites with different active carbon content were synthesized and studied by various techniques. The obtained materials can be used as adsorbents in the processes of removing organic pollutants from water. In this study, the effect of the immobilization of activated carbon in calcium alginate was investigated. Textural properties were determined by measuring low-temperature nitrogen adsorption/desorption isotherms. The largest specific surface area was recorded for ALG_C8 and amounted to 995 m²/g. The morphology of alginate materials was determined on the basis of scanning electron microscopy. The adsorption properties were estimated based on the measurements of equilibrium and adsorption kinetics. The highest sorption capacities were 0.381 and 0.873 mmol/g for ibuprofen and diclofenac, respectively. The generalized Langmuir isotherm was used to analyze the equilibrium data. A number of equations and kinetic models were used to describe the adsorption rate data, including first (FOE) and second (SOE) order kinetic equations, 1,2-mixed-order kinetic equation (MOE), fractal-like MOE equation (f-MOE), multi-exponential equation (m-exp), in addition to diffusion models: intraparticle diffusion model (IDM) and pore diffusion model (PDM). Thermal stability was determined on the basis of data from thermal analysis in an atmosphere of synthetic air.

Toxicity Assessment and Treatment Options of Diclofenac and Triclosan Dissolved in Water

The presence of pharmaceutical and personal care products in water is increasing tremendously nowadays. Typical representatives are diclofenac (DCF) and triclosan (TCS). Acute toxicity of these substances was experimentally assessed using the freshwater algae Raphidocelis subcapitata (living, immobilized). The IC50 achieved for R. subcapitata was 177.7–189.1 mg·L−1 for DCF and 5.4–17.2 µg·L−1 for TCS, whereas, regarding DCF, the results corresponded to the values observed by other authors. Concerning TCS, the results were lower than predicted and indicated TCSs’ higher toxicity. The immobilized R. subcapitata showed comparable results with its living culture for DCF only. Regarding K2Cr2O7 and TCS, the immobilized alga was more sensitive. The DCF and TCF removal from water was tested by sorption, photocatalytic and photolytic processes. TiO2 was used as a photocatalyst. Norit and SuperSorbon were used as sorbents based on activated charcoal. The DCF decomposition achieved by both photo-processes was very fast. The starting concentration fell below the detection limit in less than one minute, while bioluminescence on Aliivibrio fischeri showed no toxic intermediates formed only in the case of photocatalysis. DCF and TCS removals by sorption were significantly faster on Norit than SuperSorbon, while the bioluminescence inhibition remained insignificant.

Synergistic adsorption and degradation of diclofenac by zero-valent iron modified spent bleaching earth carbon: Mechanism and toxicity assessment

Diclofenac (DCF) is a drug compound that exists widely in water bodies, which may pose a threat to the ecological environment. In this study, spent bleaching earth (SBE) was pyrolyzed, modified with cetyltrimethylammonium bromide (CTAB) and loaded with zero-valent iron (nZVI) to obtain CTAB-SBE@C-nZVI. The effects of CTAB concentration, Fe⁰ loading, CTAB-SBE@C-nZVI dosage, and initial pH value on the removal efficiency of DCF were studied. The results showed that the DCF removal efficiency could reach a maximum of 87.0% with 2.0 g/L dosage of the optimal material, which was prepared under the conditions of 30 mmol/L CTAB concentration, 25% Fe⁰ loading, and initial pH 5. It indicated that the strong adsorption of the material and the reduction effect of nZVI can achieve high-efficiency removal of DCF. Based on the detected reaction intermediate products, four possible degradation paths were inferred. The toxicity assessment of DCF and its intermediates manifested that the degradation of DCF by CTAB-SBE@C-nZVI was a process of gradual dechlorination and toxicity reduction. CTAB-SBE@C-nZVI displayed excellent DCF removal efficiency, good stability and environmental friendliness, achieving wastes treat wastes and exhibiting good prospects.

Adsorption of Sodium Diclofenac in Functionalized Palygoskite Clays

The effects of acid and organo-functionalizations on the surface of Brazilian palygorskite clay was investigated, evaluating its potential in the adsorptive capacity of the drug sodium diclofenac present in wastewaters. The modifications on the clay structure were investigated by X-ray diffraction, X-ray fluorescence, thermogravimetric, differential thermal analysis, Fourier transform infrared spectroscopy, surface area by N₂ adsorption (77.5 K) and Zeta potential. The experimental design was carried out to find the best conditions for the adsorption tests, in which concentration, mass and pH were significant. In the kinetic study, the pseudo-second-order model better described the adsorption process for acid and organo-functionalized samples. Such results indicate that the adsorption behavior probably occurs due to the phenomenon of chemisorption. Regarding the adsorption isotherms, the Langmuir model was the one that best adjusted both the experimental data of acid and the organo-functionalized samples, whose maximum adsorption capacity were 179.88 and 253.34 mg/g, respectively. This model also indicates that the sodium diclofenac is adsorbed to monolayers homogeneously through chemisorption. In general, the studied clays proved to be suitable adsorbents for the removal of sodium diclofenac.

Efficient adsorptive removal of fluoroquinolone antibiotics from water by alkali and bimetallic salts co-hydrothermally modified sludge biochar

Fluoroquinolones are one of most commonly used antibiotics for preventing and treating bacterial infections and their unsatisfactory removal by conventional wastewater treatment technology have aroused widespread attention. A novel adsorbent of KMSBC was the first time synthesized and tested to adsorb three typical fluoroquinolone antibiotics of CIP, NOR and OFL from water. The characterization analysis showed that KMSBC possessed the superior porous structure, abundant functional groups and greater graphitic degree. Together with kinetics, isotherms, thermodynamics and critical factors (e.g., biochar dose, reaction time/temperature, fluoroquinolone antibiotics concentration, pH, co-existing ionic strength and HA concentration) analysis suggested that pore filling, π-π conjugation, H-bonding and electrostatic interaction were the key mechanisms for fluoroquinolone antibiotics adsorption by KMSBC. KMSBC exhibited the optimum adsorption performance at pH = 5 despite the adsorbates. The maximum adsorption capacity of KMSBC for CIP, NOR and OFL were 49.9, 55.7 and 47.4 mg/g at 25 °C, respectively. Also, KMSBC exhibited the good magnetic sensitivity and stability with the leaching concentrations of Fe were far below than environmental limit (GB5749-2006) at various pH (from 3 to 12), ionic strength and HA concentrations. Additionally, KMSBC performed a stable sustainable adsorption performance in recycles by NaOH regeneration. Thus, KMSBC had the potential to be a promising adsorbent for fluoroquinolone antibiotics removal with favorable adsorption capacity, environmental security and easy regeneration performance.

An efficient, green and sustainable potassium hydroxide activated magnetic corn cob biochar for imidacloprid removal

The extensive use of imidacloprid (IMI) has led to its being frequently detected in natural water, also caused the potential damage to the ecosystem. Development of efficient, green and sustainable technique is demanded to eliminate this problem. A novel biochar (KMCBC) derived from agriculture waste of corn cob was first time co-modified by potassium hydroxide (KOH), ferric chloride (FeCl₃) and zinc chloride (ZnCl₂), which showed the greater adsorption amount (410 mg g^-1 at 298 K) for imidacloprid (IMI). Pseudo-second-order kinetic and Langmuir isotherm models fitted well with the experimental data, together with the physicochemical characterization analysis, demonstrating that the adsorption process of IMI by KMCBC might be mainly controlled by micropore filling, π-π electron donor-acceptor and functional groups interactions (H-bonding and complexation). Additionally, the thermodynamics parameters suggested that IMI adsorption in this study was a spontaneous, endothermic and randomly increasing process. Besides, KMCBC owned the easy separation performance and promising environmental safety, also exhibited a high selective adsorption capacity regardless of solution pH (its optimum adsorption performance for IMI was obtained at pH = 5), inorganic ions strength and humic acid (HA) concentrations. The regenerated KMCBC (synergistic ultrasound/ethanol) could sustainably and efficiently adsorb IMI in the reuse cycles. Therefore, this study provided an efficient, green and sustainable adsorbent of KMCBC for IMI removal.

Removal of difenoconazole and nitenpyram by composite calcium alginate beads during apple juice clarification

A novel genipin crosslinked calcium alginate/chitosan/polydopamine composite beads (g-Alg/CS/PDA) was synthesized for the removal of residual difenoconazole and nitenpyram during the clarification of apple juice. The composite beads with low potential health risks for all of the main materials were natural, green and biocompatible. Since g-Alg/CS/PDA can both clarify and adsorb, pesticide residues could be removed during the clarification of juice without additional steps. The g-Alg/CS/PDA beads were characterized, and the adsorption parameters, including the pesticide residue levels, adsorption time, pH, ionic strength, fructose concentration and adsorbent dose, were optimized. The adsorption data were fitted to the Freundlich isotherm model (R² = 0.9604, 0.9625) and the pseudo-second-order kinetic model (R² = 0.9993, 0.9999). The results indicated that the adsorption behavior of beads was heterogeneous. Moreover, the rate was controlled by several factors. The adsorption mechanism of two pesticides was also discussed. Hydrophobic and π-π conjugation interactions played a dominant role for the adsorption of difenoconazole, while hydrogen bonding and electrostatic interactions were the main factors for nitenpyram.

Intercalation of a Cationic Cyanine Dye Assisted by Anionic Surfactants within Mg-Al Layered Double Hydroxide

An original route for the intercalation of a 1,1'-diethyl-2,2'-cyanine iodide (PIC) cationic dye, through the use of anionic surfactants as vector/carrier phases, within Mg-Al layered double hydroxide (LDH) was investigated. From the data acquired from complementary techniques (X-ray diffraction, infrared and UV-visible spectroscopies, thermogravimetry, and fluorimetry), it appears that both the intercalation and aggregation states of the cationic dye within the internal structure of LDH mainly depend on both the surfactant state (monomer form or spherical micelle) and its amount. The intercalation of PIC at a low molar ratio to the anionic surfactant leads to the formation of J-aggregates with singular fluorescence properties that mainly depend on the nature of the anionic surfactant used for the co-intercalation process. The results obtained in this study open new routes for the intercalation of cationic species, assisted by anionic surfactants, within LDHs.

Pharmaceuticals Removal by Adsorption with Montmorillonite Nanoclay

The problem of purifying domestic and hospital wastewater from pharmaceutical compounds is becoming more and more urgent every year, because of the continuous accumulation of chemical pollutants in the environment and the limited availability of freshwater resources. Clay adsorbents have been repeatedly proposed as adsorbents for treatment purposes, but natural clays are hydrophilic and can be inefficient for catching hydrophobic pharmaceuticals. In this paper, a comparison of adsorption properties of pristine montmorillonite (MMT) and montmorillonite modified with stearyl trimethyl ammonium (hydrophobic MMT-STA) towards carbamazepine, ibuprofen, and paracetamol pharmaceuticals was performed. The efficiency of adsorption was investigated under varying solution pH, temperature, contact time, initial concentration of pharmaceuticals, and adsorbate/adsorbent mass ratio. MMT-STA was better than pristine MMT at removing all the pharmaceuticals studied. The adsorption capacity of hydrophobic montmorillonite to pharmaceuticals decreased in the following order: carbamazepine (97%) > ibuprofen (95%) > paracetamol (63-67%). Adsorption isotherms were best described by Freundlich model. Within the pharmaceutical concentration range of 10-50 µg/mL, the most optimal mass ratio of adsorbates to adsorbents was 1:300, pH 6, and a temperature of 25 °C. Thus, MMT-STA could be used as an efficient adsorbent for deconta×ating water of carbamazepine, ibuprofen, and paracetamol.

Highly efficient removal of imidacloprid using potassium hydroxide activated magnetic microporous loofah sponge biochar

Extensive application of imidacloprid (IMI) in pest control and its undesirable removal efficiency enabled it to be a critical global challenge. Low cost, efficient, sustainable and environment-friendly technologies are urgently needed to be developed to remove IMI from water. A novel adsorbent of potassium hydroxide activated magnetic microporous loofah sponge biochar (KOH+Fe/Zn-LBC) was synthesized, as well as its adsorption capacity and mechanisms for IMI were investigated in this study. KOH+Fe/Zn-LBC had the superior pore structure (surface area and pore volume) and its maximum adsorption capacity for IMI could reach 738 mg g^-1 at 298 K. Kinetics, isotherms, thermodynamics and characterization analysis suggested that pore filling, hydrogen bonding and π-π conjugation were its main adsorption mechanisms. Additionally, the thermodynamic parameters described that IMI adsorption was a spontaneous, endothermic and less random process. Particularly, the magnetic separation of KOH+Fe/Zn-LBC was beneficial for its reuse. Ultrasound and ethanol co-processing could effectively regenerate the used KOH+Fe/Zn-LBC and maintain its stable sustainable adsorption capacity (99.4% of its fresh adsorption capacity after five reuse cycles). Besides, KOH+Fe/Zn-LBC exhibited a stable adsorption capacity and environmental safety in a wide pH range. Therefore, KOH+Fe/Zn-LBC has the potential to be an efficient, green and sustainable adsorbent for neonicotinoids removal.

Over-sulfated soils and sediments treatment: A brief discussion on performance disparities of biological and non-biological methods throughout the literature

High sulfate concentrations in industrial effluents as well as solid materials (excavated soils, dredged sediments, etc.) are a major hindrance for circular economy outlooks. SO₄^2- acceptability standards are indeed increasingly restrictive, given the potential outcomes for public health and ecosystems. This literature review deals with the treatment pathways relying on precipitation, adsorption and microbial redox principles. Although satisfactory removal performances can be achieved with each of them, significant yield differences are displayed throughout the bibliography. The challenge here was to identify the parameters leading to this variability and to assess their impact. The precipitation pathway is based on the formation of two main minerals (ettringite and barite). It can lead to total sulfate removal but can also be limited by aqueous wastes chemistry. Stabilizer kinetics of formation and equilibrium are highly constrained by background properties such as pH, Eh, SO₄^2- saturation state and inhibiting metal occurrences. Regarding the adsorption route, sorbents' intrinsic features such as the q_max parameter govern removal yields. Concerning the microbial pathway, the chemical oxygen demand/SO₄^2- ratio and the hydraulic retention time, which are classically evoked as yield variation factors, appear here to be weakly influential. The effect of these parameters seems to be overridden by the influence of electron donors, which constitute a first order factor of variability. A second order variability can be read according to the nature of these electron donors. Approaches using simple monomers (ethanol lactates, etc.) perform better than those using predominantly ligneous organic matter.

Application of Ni0.5Zn0.5Fe2O4 magnetic nanoparticles for diclofenac adsorption: isotherm, kinetic and thermodynamic investigation

Ni_0.5Zn_0.5Fe₂O₄ magnetic nanoparticles were synthesized to obtain a new efficient adsorbent for diclofenac sodium (DF) removal. Fourier Transform Infrared (FTIR), Energy Dispersive Spectrometer (EDS), scanning electron microscope (SEM), Brunauer-Emmett-Teller (BET) and vibrating sample magnetometer (VSM) were applied to characterize the prepared adsorbent. These analyses revealed that adsorbent was successfully prepared with average particle diameter of about 50 nm and a BET surface area of 168.09 m²/g. The saturation magnetization value of magnetic nanoparticles (MNPs) was found to be 24.90 emu/g, thus, adsorbent was efficiently separated from the solution by a facile and rapid magnetic separation process. The effect of adsorption time, amount of adsorbent, initial pH of the solution, initial diclofenac concentration and temperature on the removal of DF were evaluated. Also, the adsorption data were best fitted to the pseudo-first-order kinetic model and Langmuir isotherm model. The thermodynamics studies suggested spontaneous and exothermic adsorption. The maximum diclofenac adsorption amount of the synthesized nanoadsorbent was 52.91 mg/g, which is higher than many recently studied adsorbents.

Capturing Dioclea Reflexa Seed Bioactives on Halloysite Nanotubes and pH Dependent Release of Cargo against Breast (MCF-7) Cancers In Vitro

In this work, optimization parameters were developed to capture plant metabolites from Dioclea Reflexa (DR) seed ex-tracts onto halloysites nanotubes (HNTs). A one-step pool of the crude extracts at neutral pH from the HNT lumen failed to elicit a reduction in breast cancer, Michigan Cancer Foundation-7 (MCF-7) cell viability. However, the pH-dependent elution of metabolites revealed that the acidic pH samples exhibited profound antiproliferative effects on the cancer cells compared to the basic pH metabolites using both trypan blue dye exclusion assay and 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-2H-tetrazolium bromide (MTT) viability test. pH~5.2 samples demonstrated by half-maximal inhibitory concentration (IC50) of 0.8 mg and a cyclic voltammetry oxidation peak potential and current of 234 mV and 0.45 µA, respectively. This indicates that the cancer cells death could be attributed to membrane polarization/depolarization effects of the sample. Fluorescence-activated cell sorting (FACS) studies confirmed that the plant metabolites affected breast cancer apoptotic signaling pathways of cell death. The studies proved that plant metabolites could be captured using simplified screening procedures for rapid drug discovery purposes. Such procedures, however, would require the integration of affordable analytical tools to test and isolate individual metabolites. Our approach could be an important strategy to create a library and database of bioactive plant metabolites based on pH values.

Oxidation of diclofenac in the presence of iron(II) octacarboxyphthalocyanine

This paper presents the results of the research on the influence of catalytic activity of iron(II) octacarboxyphthalocyanines (FePcOC) on the transformation of diclofenac (DCF) which is the most popular anti-inflammatory analgesic. Diclofenac poses a serious threat to the natural environment. The paper demonstrates that diclofenac, in the presence a monomeric form of iron octacarboxyphthalocyanine and hydroxyl radicals (HO^•) (from H₂O₂), undergoes a transformation into diclofenac-2,5-iminoquinone (DCF-2,5-IQ), causing distinct changes in the UV-Vis absorption spectrum. In the presence of iron octacarboxyphthalocyanine and H₂O₂, the previously colourless diclofenac solution becomes intense orange. As a result, a new band at approx. 450 nm appears in the absorption spectrum. HPLC analysis has shown that the concentration of diclofenac decreases with time. TD-DFT calculations using the CAM-B3LYP/6-31+G (d, p) method have been conducted to confirm experimental data concerning the formation of a new band at λ_max = 450 nm.

Use of a clay mineral and its nonionic and cationic organoclay derivatives for the removal of pharmaceuticals from rural wastewater effluents

A Na⁺ exchanged montmorillonite clay (Na-Mt) and its organoclay derivatives prepared with benzyldimethyltetradecylammonium (BDTA) cationic and polyoxyethylene (20)oleyl-ether (Brij-O20) non-ionic surfactants were used for first time at our knowledge as adsorbents the removal diverse pharmaceuticals (PPs) from samples collected in a rural wastewater facility (town of Josnes in France). The selected facility showed a poor efficiency for the elimination of PPs that were permanently release to the environment. Although involving different interactional mechanisms, the whole adsorbents Na-Mt, nonionic Brij-Mt and cationic BDTA-Mt organoclays, could remove the entire PPs of various chemical nature in a low concentration regime (ng L^-1), where electrostatic interactions mainly controlled the adsorption. Thus, the organic PPs cations were preferentially adsorbed onto Na-Mt and Brij_0.4-Mt (with its dual hydrophilic-hydrophobic nature) while anionic PPs showed a bold affinity to BDTA-Mt. The hydrophobic environment generated by the intercalation of surfactants within the interlayer space of organoclays conferred a versatility for the adsorption of numerous PPs through weak molecular forces (Van der Waals and/or pi-pi interactions). The study confirmed the proper efficiency of the studied layered materials including organoclays and emphasized about their promising interests in water remediation strategy.

Potential Application of A Synthetic Organo-funtionalized High Load Expandable Mica as A Drug Carrier for Controlled Release

BACKGROUND

In this work the cytotoxicity and gastric and gastrointestinal resistance of a high-load synthetic expandable mica, Na-mica-4, is studied for the first time. The hydrophilic character of this clay mineral can be modified by ion exchange reaction between Na+ inorganic cations housed in the interlayer space, and surfactant molecules, resulting in the formation of an organophilic material. This adsorption capability of organic compounds makes them very useful for a wide range of applications, such as their use as drug carriers. Previous studies have shown the high adsorption capacity of organofunctionalized Na-mica-4 of different types of drugs. Objetive: To carry out initial trials aimed at testing the cytotoxicity of a synthetic organofunctional expandable mica and evaluating its resistance to gastric and gastrointestinal digestion.

METHODS

A highly charged sodium mica (Na-mica-4) was synthesized and organofunctional by cationic exchange with an alkylamine, primary amine of 18 carbon atoms (C18-mica-4). Both were characterized by X-ray diffraction, field transmission electron microscopy, surface-specific analysis, differential scanning calorimetry, and thermal gravimetric analysis. In addition, screening cytotoxicity trials were conducted on the human intestinal cell line Caco-2 with C18-mica-4 (0-125 μg/ml).

RESULTS

Only one of the endpoints evaluated (the reduction of tetrazolium MTS salt by dehydrogenase enzymes) showed a significant decrease in cellular viability after 48h at the highest concentration tested. C18-mica-4 shows structural resistance to both, gastric and gastrointestinal, digestion.

CONCLUSION

A successful development of a functionalized mica has been made with a promising potential application as a carrier to the drug.

Organically Modified Bentonite as an Efficient and Reusable Adsorbent for Triclosan Removal from Water

Triclosan, an antibacterial agent, in the environment is of great concern; thus, an efficient method for its removal from an aqueous system is required. Removal of triclosan from water was achieved by an organically modified bentonite, dioctadecyldimethylammonium bentonite. The highest adsorbed amount achieved under the optimized conditions was 1750 mg·g^-1, which is higher than that reported using such adsorbents as activated carbons, carbon nanotubes, zeolites, and other nanoporous materials. Complete removal of triclosan was achieved from the aqueous triclosan solution at a concentration 10 mg·L^-1 using 3 mg/60 mL of 2C18-BT. The adsorbent was reusable, as examined by washing and reuse of the adsorbent for 5 cycles.

Magnetic Ti3C2Tx (Mxene) for diclofenac degradation via the ultraviolet/chlorine advanced oxidation process

In this study, a magnetic titanium carbide (Ti₃C₂T_x) MXene was synthesized through a one-step chemical co-precipitation method using ammonium bifluoride as a mild etchant and was investigated for photocatalytic degradation of diclofenac (DCF) via the ultraviolet (UV)/chlorine process. The DCF degradation was enhanced by the generation of active radicals such as the hydroxyl radical and reactive chlorine species compared with that resulting from UV and chlorination treatment alone as well as UV/H₂O₂ processes at pH 7. The first-order rate constant of the UV/chlorine process was 0.1025 min^-1, which is 12.7 and 6.8 times higher than those of the only UV and UV/H₂O₂ processes, respectively. Magnetic nanoparticles on the surfaces of Ti₃C₂T_x sheets not only enhanced the adsorption capacity of the synthesized composite but also increased the rate of electron transfer in solution. In addition, the effects of different operating conditions such as magnetic Ti₃C₂T_x dose, pH, and initial chlorine concentration on DCF degradation were investigated. Magnetic Ti₃C₂T_x showed high stability and photodegradation efficiency during seven consecutive degradation reaction cycles. The derivatives of DCF during the photocatalytic degradation process were also investigated based on the observed intermediate products and a degradation pathway was proposed. Thus the synthesized magnetic Ti₃C₂T_x is a simple and affordable photocatalyst, which can significantly enhance DCF degradation in the UV/chlorine advanced oxidation process.

Monitoring diclofenac adsorption by organophilic alkylpyridinium bentonites

Organoclays have been applied as efficient adsorbents for pharmaceutical pollutants from aqueous solution. In this work, dodecylpyridinium chloride (C₁₂pyCl) and hexadecylpyridinium chloride (C₁₆pyCl) cationic surfactants were used for the preparation of organobentonites destined for diclofenac sodium (DFNa) adsorption, an anionic drug widely detected in wastewater. The organofunctionalization of the clay samples was performed under microwave irradiation at 50 °C for 5 min with surfactant amounts of 100% and 200% in relation to the cation exchange capacity (CEC) of the pristine bentonite. The amount of incorporated ammonium salts based on CHN elemental analysis was higher for all samples prepared with 200% of the CEC. The basal spacings of the organoclays ranged from 1.54 to 2.13 nm, indicating the entrance of organic cations into the interlayer spacing of the clay samples, and the spacing depended on the size of the alkyl organic chain. The hydrophobic character of the organobentonites was verified by thermogravimetry and infrared spectroscopy (FTIR). The adsorption isotherms showed that the drug capacity adsorption was influenced by the amount of surfactant incorporated into the bentonite, the packing density and the arrangement of the surfactants in the interlayer spacing. Zeta potential measurements of the organobentonites and FTIR analysis after drug adsorption suggested that electrostatic and nonelectrostatic interactions contributed to the mechanism of adsorption.

Effective adsorption of diclofenac sodium from neutral aqueous solution by low-cost lignite activated cokes

Activated cokes have attracted great interest inwater treatment to remove organic pollutants due to their low cost and specific textural properties. In this study, adsorptive removal of diclofenac sodium (DCF) from neutral aqueous solution by available lignite activated cokes (LACs) was reported for the first time. Diclofenac sodium could be quickly removed from aqueous solution by LAC-2, with the maximum Langmuir adsorption capacity q_m of 224 mg/g at pH 6.5. Characterization results (including scanning electron microscopy, transmission electron microscopy, elemental analyses, Boehm titrations, N₂ adsorption-desorption isotherms and Fourier transform infrared spectroscopy) and a series of adsorption kinetics, adsorption isotherms model studies revealed that high porosity with developed macro- and micropore structures on LAC-2, as well as high content of phenolic groups, could obviously enhance the DCF adsorption capacity and rate. Moreover, LAC-2 showed high affinity towards DCF at low concentrations, as well as good reusability after three adsorption-desorption cycles. pH effect studies revealed that hydrogen-bonding interaction plays an important role during adsorption, accompanied with certain contribution from electrostatic interaction and π-π interaction. This study indicates the promising potential of LAC-2 as an efficient, low-cost and recyclable material for DCF removal from water bodies.

Laponites® for the Recovery of 133Cs, 59Co, and 88Sr from Aqueous Solutions and Subsequent Storage: Impact of Grafted Silane Loads

In this study, silylated Laponites^® (LAP) were synthetized with various loads of 3-aminopropyltriethoxysilane (APTES) to evaluate their adsorption properties of ¹³³Cs, ⁵⁹Co, and ⁸⁸Sr during single-solute and competitive experiments. The increase in the initial load of APTES increased the adsorbed amount of APTES in the resulted grafted clay. The characterization of LAP-APTES exhibited a covalent binding between APTES and LAP and emphasized the adsorption sites of APTES for each tested load. In comparison with raw LAP, LAP-APTES displayed significantly higher adsorption properties of Co²⁺, Cs⁺, and Sr²⁺. The competitive adsorption of these three contaminants provides a deeper understanding of the affinity between adsorbate and adsorbent. Therefore, Co²⁺ displayed a strong and specific adsorption onto LAP-APTES. Except for Cs⁺, the adsorption capacity was improved with increasing the load of APTES. Finally, the desorption behavior of the three contaminants was tested in saline solutions. Cs⁺ and Sr²⁺ were significantly released especially by inorganic cations displaying the same valence. Conversely, desorption of Co²⁺ was very low whatever the saline solution. LAP-APTES, therefore, presented suitable adsorption properties for the removal of radionuclides especially for Co²⁺, making this material suitable to improve the decontamination of radioactive wastewaters.

Tuning down the environmental interests of organoclays for emerging pollutants: Pharmaceuticals in presence of electrolytes

The impact of electrolytes on the adsorption of emerging pollutants: pharmaceuticals onto layered materials: a raw clay mineral and its nonionic and cationic organoclay derivatives was studied. The selected pharmaceuticals: amoxicillin, norfloxacin, sulfamethoxazole, metoprolol, carbamazepine, and trimethoprim show different electric charges: zwitterionic, anionic, cationic and neutral and hydrophobic character (different LogP). Without any salts, the set of complementary data obtained by UV and infrared spectroscopies, X-ray diffraction points out the importance of the electric charge which represents a key parameter in both the spontaneity and feasibility of the adsorption. In contrast, the hydrophobicity of the analytes plays a minor role but determines the magnitude of the adsorbed amount of pharmaceuticals onto organoclays. With a dual hydrophilic and hydrophobic behavior, nonionic organoclay appears to be the most polyvalent material for the removal of the pharmaceuticals. In the presence of electrolytes (NaCl at a concentration of 1 × 10^-2 mol L^-1), both nonionic and cationic organoclays show a decrease of their efficiencies, whereas the adsorption is particularly enhanced for Na-Mt except for the cationic species (trimethoprim and metoprolol). Thus, in realistic experimental conditions close to those of natural effluents, raw clay mineral appears as the most appropriate sorbent for the studied pharmaceuticals while it raises the question of the usefulness of organoclays in water remediation strategy.

Rapid removal of diclofenac in aqueous solution by soluble Mn(III) (aq) generated in a novel Electro-activated carbon fiber-permanganate (E-ACF-PM) process

Electrolysis and permanganate (PM) oxidation are two commonly used technologies for water treatment. However, they are often handicapped by their slow reaction rates. To improve the removal efficiency of refractory contaminants, we combined electrolysis with PM using an activated carbon fiber (ACF) as cathode (E-ACF-PM) for the first time to treat diclofenac (DCF) in aqueous solution. Up to 90% DCF was removed in 5 min by E-ACF-PM process. In comparison, only 3.95 and 27.35% of DCF was removed by individual electrolysis and PM oxidation at the same time, respectively. Acidic condition was more conducive to DCF removal. Surprisingly, soluble Mn(III) _(aq) formed on the surface of ACF was demonstrated as the principal oxidizing agent in E-ACF-PM process. Further studies showed that all three components (electrolysis + ACF + PM) were necessary to facilitate the heterogeneous generation of reactive Mn(III) _(aq). Moreover, SEM images and XPS spectra of ACF before and after treatment revealed that the morphologies and elemental compositions of reacted ACF were nearly unchanged during the E-ACF-PM process. ACF can be remained active and utilized to the rapid degradation of DCF in E-ACF-PM process even after reused for 20 times. Therefore, the E-ACF-PM process may provide a novel and effective alternative on the generation of reactive Mn(III) _(aq) in situ for water treatment by green electrochemical reactions.

Eosin Removal by Cetyl Trimethylammonium-Cloisites: Influence of the Surfactant Solution Type and Regeneration Properties

The effect of the counteranion of hexadecyltrimethylammonium salts on the physico-chemical properties of organoclays was investigated, using a selected natural clay mineral with a cation exchange capacity of 95 meq/100 g. The uptake amount of C16 cations was dependent on the hexadecyltrimethylammonium (C16) salt solution used, the organoclay prepared from C16Br salt solution exhibited a value of 1. 05 mmole/g higher than those prepared from C16Cl and C16OH salt solutions. The basal spacing of these organoclays was in the range of 1.81 nm to 2.10 nm, indicating a similar orientation of the intercalated surfactants, and could indicated that the excess amount of surfactants, above the cation exchange capacity of 0.95 meq/g could be adsorbed on the external surface of the clay mineral sheets. These organoclays were found to be stable in neutral, acidic, and basic media. The thermal stability of these organoclays was carried out using thermogravimetric analysis and in-situ X-ray diffraction (XRD) techniques. The decomposition of the surfactant occurred at a maximum temperature of 240 °C, accompanied with a decrease of the basal spacing value close to 1.42 nm. The application of these organoclays was investigated to remove an acidic dye, eosin. The removal amount was related to the initial used concentrations, the amount of the surfactants contents, and to the preheated temperatures of the organoclays. The removal was found to be endothermic process with a maximum amount of 55 mg of eosin/g of organoclay. The value decreased to 25 mg/g, when the intercalated surfactants were decomposed. The reuse of these organoclays was limited to four regeneration recycles with a reduction of 20 to 30%. However, noticeable reduction between 35% to 50% of the initial efficiency, was achieved after the fifth cycle, depending of the used organoclays.

Mechanisms of Methylparaben Adsorption onto Activated Carbons: Removal Tests Supported by a Calorimetric Study of the Adsorbent⁻Adsorbate Interactions

: In this study, the mechanisms of methylparaben adsorption onto activated carbon (AC) are elucidated starting from equilibrium and thermodynamic data. Adsorption tests are carried out on three ACs with different surface chemistry, in different pH and ionic strength aqueous solutions. Experimental results show that the methylparaben adsorption capacity is slightly affected by pH changes, while it is significantly reduced in the presence of high ionic strength. In particular, methylparaben adsorption is directly dependent on the micropore volume of the ACs and the π- stacking interactions, the latter representing the main interaction mechanism of methylparaben adsorption from liquid phase. The equilibrium adsorption data are complemented with novel calorimetric data that allow calculation of the enthalpy change associated with the interactions between solvent-adsorbent, adsorbent-adsorbate and the contribution of the ester functional group (in the methylparaben structure) to the adsorbate⁻adsorbent interactions, in different pH and ionic strength conditions. It was determined that the interaction enthalpy of methylparaben-AC in water increases (absolute value) slightly with the basicity of the activated carbons, due to the formation of interactions with π- electrons and basic functional groups of ACs. The contribution of the ester group to the adsorbate-adsorbent interactions occurs only in the presence of phenol groups on AC by the formation of Brønsted⁻Lowry acid⁻base interactions.