Synergistic degradation of phenols using peroxymonosulfate activated by CuO-Co3O4@MnO2 nanocatalyst

Activating peroxymonosulfate with MOF-derived NiO-NiCo2O4/titanium membrane for water treatment: A non-radical dominated oxidation mechanism

Traditional peroxymonosulfate (PMS) catalytic membranes dominated by radical pathways often face interference from complex components in water bodies. Herein, we employed a controlled electro-deposition technique to coat a Ni-Co metal-organic framework (MOF) precursor onto titanium hollow fiber membrane (THFM), followed by high-temperature calcination to synthesize a MOF-derived NiO-NiCo2O4/THFM (M-NNCO-THFM) PMS catalytic membrane. Then, the M-NNCO-THFM filtration integrated with PMS activation (MFPA process) for water treatment. Experimental results demonstrated that the M-NNCO-THFM MFPA process successfully achieved complete phenol (PE) removal via a non-radical-dominated degradation pathway, involving singlet oxygen (1O2) and electron transfer, while exhibiting wide pH adaptability and exceptional stability in complex water matrices. Mechanism analysis revealed that the electron transfer process was significantly enhanced by the MOF-derived heterojunction structure, which increased the flat-band potential from 0.39 eV to 0.56 eV, thereby facilitating efficient electron transfer for PE removal. The non-radical 1O2 pathway was primarily due to the cycling of metal valence states (Ni2+/Co3+), leading to the reduction of Co2+ and its reaction with PMS, resulting in the generation of reactive species. Furthermore, electrochemical measurements indicated that the M-NNCO-THFM exhibited lower charge transfer resistance and enhanced charge transfer efficiency compared to non-MOF-derived NNCO-THFM, corresponding to the superior catalytic performance and electrochemically active surface area of M-NNCO-THFM.

Mesoporous cobalt-manganese layered double hydroxides promote the activation of calcium sulfite for degradation and detoxification of metronidazole

Metronidazole (MNZ), a commonly used antibiotic, poses risks to water bodies and human health due to its potential carcinogenic, mutagenic, and genotoxic effects. In this study, mesoporous cobalt-manganese layered double hydroxides (CoxMny-LDH) with abundant oxygen vacancies (Ov) were successfully synthesized using the co-precipitation method and used to activate calcium sulfite (CaSO3) with slight soluble in water for MNZ degradation. The characterization results revealed that Co2Mn-LDH had higher specific areas and exhibited good crystallinity. Co2Mn-LDH/CaSO3 exhibited the best catalytic performance under optimal conditions, achieving a remarkable MNZ degradation efficiency of up to 98.1 % in only 8 min. Quenching experiments and electron paramagnetic resonance (EPR) tests showed that SO4•- and 1O2 played pivotal roles in the MNZ degradation process by activated CaSO3, while the redox cycles of Co2+/Co3+ and Mn3+/Mn4+ on the catalyst surface accelerated electron transfer, promoting radical generation. Three MNZ degradation routes were put forward based on the density functional theory (DFT) and liquid chromatography-mass spectrometer (LC-MS) analysis. Meanwhile, the toxicity analysis result demonstrated that the toxicity of intermediates post-catalytic reaction was decreased. Furthermore, the Co2Mn-LDH/CaSO3 system displayed excellent stability, reusability, and anti-interference capability, and achieved a comparably high removal efficiency across various organic pollutant water bodies. This study provides valuable insights into the development and optimization of effective heterogeneous catalysts for treating antibiotic-contaminated wastewater.

Insight into the role of reactive species on catalyst surface underlying peroxymonosulfate activation by P-Fe2MnO4 loaded on bentonite for trichloroethylene degradation

In this study, bentonite supporting phosphorus-doped Fe2MnO4 (BPF) was synthesized and applied for PMS activation to degrade TCE. Morphology and structure characterization results indicated the successfully synthesized of BPF, and the BPF/PMS system not only featured high TCE removal (97.4%) but also high reaction rate constant (kobs = 0.0554 min-1) and PMS utilization (70.4%, kobs = 0.0228 min-1). According to the results of various experiments, massive oxygen vacancies on P-Fe2MnO4 alter its charge balance and facilitate the electron transfer process named adjacent transfer (direct electron capture by adsorbed PMS from adjacent TCE). Mn(III) is the main adsorption site for PMS, and the hydroxyl groups on the catalyst (Fe sites of P-Fe2MnO4, Si and Al sites of bentonite) can also offer binding sites for PMS. The hydrogen-bonded PMS on Fe(III) and Mn(III) sites will subsequently accept the discharged electrons to generate free radicals and high-valent metal species. Meanwhile, electron loss of HSO5- that chemically bonded to hydroxyl groups on bentonite will generate SO5•-, which will further produce 1O2 through self-bonding. the active species on the catalyst surface contribute 65% of TCE degradation in the heterogeneous catalytic oxidation system.

Hollow CoP/carbon as an efficient catalyst for the peroxymonosulfate activation derived from phytic acid assisted metal-organic framework

The catalyst's composition and rationally designed structure is significantly interlinked with its performance for wastewater remediation. Here, a novel hollow cobalt phosphides/carbon (HCoP/C) as an efficient catalyst for activating peroxymonosulfate (PMS) was prepared. The ZIF-67 was synthesized first, followed by phytic acid (PA) etching and then heat treatment was used to get HCoP/C. The PA was used as an etching agent and a source of phosphorus to prepare HCoP/C. To analyze catalytic performance, another solid cobalt phosphides/carbon (SCoP/C) catalyst was prepared for comparison. In contrast to SCoP/C, the HCoP/C exhibited higher catalytic efficiency when used to activate PMS to degrade Bisphenol A (BPA). The results showed that about 98 % of targeted pollutant BPA was removed from the system in 6 min with a rate constant of 0.78 min-1, which was 4 times higher than the solid structure catalyst. The higher catalytic performance of HCoP/C is attributed to its hollow structure. In the study, other parameters such as BPA concentration, temperature, pH, and different catalyst amount were also tested. Moreover, the electron paramagnetic resonance (EPR) and radical quenching analysis confirmed that sulfate radicals were dominant in the HCoP/C/PMS system.

Photocatalytic activation of sulfite by maghemite (γ-Fe2O3) for iohexol degradation and alleviation effect of HCO3- on water acidification

Photo-catalyzing sulfite (S(IV)) for the generation of sulfate radical (SO4•-) has emerged as a novel advanced oxidation process (AOP) recently. However, both the potential of soil minerals as effective photocatalysts and the process of water acidification due to S(IV) oxidation have been overlooked. Herein, maghemite (γ-Fe2O3), a typical soil iron oxide with excellent photocatalytic reactivity like hematite and magnetic-collectible property like magnetite, was successfully used to activate S(IV) for iohexol degradation under visible light irradiation. As a result, 91.3% of iohexol was eliminated within 15 min at 0.1 g/L maghemite and 0.5 mM S(IV) under neutral conditions. The influencing factors, including initial pH, catalyst dosage, S(IV) amount, co-existing substances and water matrix, were systematically investigated. The maghemite/S(IV)/vis system exhibited superior performance in iohexol degradation at a wide pH range (3-10). It was found that the released proton via S(IV) oxidation led to severe water acidification. Interestingly, a low dose of HCO3- could evidently resist water acidification with little influence on iohexol elimination. Radical quenching experiments and electron spin resonance (ESR) analysis confirmed that SO4•-, •OH and •O2- were involved in iohexol abatement with SO4•- being the dominant reactive species. Compared with hydrogen peroxide, persulfate and peroxymonosulfate, the established maghemite/S(IV)/vis system achieved much more remarkable degradation performance. Furthermore, the reactivity of the catalyst was not obviously reduced even after 10 runs of reaction. This study expands the application of soil iron oxide mineral in S(IV) activation in water treatment and proposes an approach to regulate water acidification in S(IV)-based AOP.

Activation of peroxymonosulfate with biochar-supported CuO (CuO@BC) for natural organic matter removal and membrane fouling control

To achieve excellent activation efficiency of peroxymonosulfate (PMS), this work prepared a biochar-supported CuO (CuO@BC) catalyst, and the CuO@BC/PMS system was proposed to remove the organic matter in natural surface water and reduce the fouling of ultrafiltration membrane. The successful synthesis of CuO@BC was demonstrated through characterization of its microscopic morphology and chemical composition by various techniques. The prepared heterogeneous catalyst showed a strong catalytic effect on PMS, which significantly removed natural organic matter through the production of active substances (•OH, SO4•-, O2•- and 1O2) from water. With respective degradation rates of 39.4% and 59.4%, the concentrations of DOC and UV254 dropped to 1.702 mg/L and 0.026 cm-1, respectively. Additionally, the CuO@BC/PMS oxidation displayed potent oxidation capabilities for contaminants and fluorescent organics with various molecular weights. The system effectively decreased the amount of organic matter that caused reversible and irreversible fouling of polyethersulfone membranes in natural water by 85.8% and 56.3%, respectively. The main fouling mechanisms changed as well, with standard and complete blocking dominating the entire filtration process. The results demonstrated the capacity of the CuO@BC/PMS system to remove contaminants in natural water and mitigate membrane fouling.

Co-based MOF heterogeneous catalyst for the efficient degradation of organic dye via peroxymonosulfate activation

In this study, a new cobalt-based metal-organic framework (JLNU-500), [Co2(OH)(PBA)(AIP)]·3DMA·0.75H2O (4-(pyridin-4-yl) benzoic acid (HPBA), 5-aminoisophthalic acid (H2AIP) and N,N-dimethylacetamide (DMA)), was fabricated using a solvothermal method. JLNU-500 has 3D network architecture with 1D nanopore channels. The prepared JLNU-500 can activate peroxymonosulfate (PMS) for Rhodamine B (RhB) dye decolorization. Interestingly, catalyst JLNU-500 exhibited high efficiency for PMS activation, and nearly 100% (above 99.8%) removal of RhB with a high concentration (50.0 mg L-1, 100 mL) was achieved within 6 min. The reaction rate constant of the JLNU-500/PMS system was 1.02 min-1 calculated based on the pseudo-first-order kinetics, which is higher than that of the other reported catalysts. Furthermore, the factors, which could influence PMS activation were also investigated, such as PMS dosage, catalyst dosage, pollutant RhB concentration, reaction temperature and solution pH. More importantly, the radical trapping experiments ferreted out that sulfate (SO4˙-) and hydroxyl (˙OH) radicals were the dominating oxidants in the removal of RhB. Moreover, the possible degradation mechanism was elucidated. This study provides new prospects for fabricating new MOFs that can potentially be employed for high-efficiency catalytic oxidation as heterogeneous catalysts.

pH adjustable MgAl@LDH-coated MOFs-derived Co2.25Mn0.75O4 for SMX degradation in PMS activated system

Sulfate radical-based advanced oxidation processes (SR-AOPs) is considered as one of the most promising technologies for antibiotic pollution. In this study, a core-shell catalyst of cobalt-manganese oxide derived from CoMn-MOFs coating by MgAl-LDH (Co/Mn@LDH) was synthesized for peroxymonosulfate (PMS) activation to degrade sulfamethoxazole (SMX). Degradation efficiency of nearly 100% and a mineralization efficiency of 68.3% for SMX were achieved in Co/Mn@LDH/PMS system. Mn species and out shell MgAl-LDH greatly suppressed the cobalt ions leaching, which only 23 μg/L Co ions were detected by ICP after the reaction. SO4·- was identified as dominant reactive species in the system. Furthermore, the possible reactive sites of SMX were predicted by the density functional theory (DFT) calculations. And the intermediates of SMX were detected by LC-MS and the degradation pathway was proposed based on the results above. The ECOSAR results suggested the intermediates of SMX showed a relatively low toxicity compared to SMX, indicating huge potential of utilization of Co/Mn@LDH in SR-AOPs system.

Degradation of dimethyl phthalate through Fe(II)/peroxymonosulphate heightened by fulvic acid: efficiency and possible mechanism

Ferrous iron (Fe(II)) reacts with peroxymonosulphate (PMS) to form active oxidants that can degrade refractory organic pollutants. However, the conversion rate of Fe(III) to Fe(II) is slow, which limits its actual application. In the study, the effect of fulvic acid (FA) on the degradation of dimethyl phthalate (DMP) by Fe(II)/PMS was investigated. Moreover, the degradation process of DMP was predicted by the preliminary identification of active free radicals and intermediates. As expected, FA gave rise to a higher concentration of Fe(II) than that in Fe(II)/PMS to enhance the removal of DMP in Fe(II)/PMS system. The precipitate, involved in FA and iron, was an important composite to promote the degradation of DMP in the system. Also, the response surface methodology (RSM) was applied to model and optimize the degradation conditions of DMP. The highest removal efficiency (85.70%) was obtained at pH = 3.86, [PMS] = 0.96 mM, [FA] = 11.44 mg/L and [DMP] = 5 µM. The results of free radical quenching experiments and EPR showed that •OH and SO₄^•- were the main active radicals in this system. The degradation intermediates of DMP were monomethyl phthalate (MMP), phthalic acid and benzoic acid. Discoveries of this study had raised the current understanding of the application of FA keeping the cycles of Fe(II)/Fe(III) for peroxymonosulphate activation, which could afford valuable information for the degradation of organic pollutants by FA/Fe(II)/PMS.

Enhanced Heterogeneous Peroxymonosulfate Activation by MOF-Derived Magnetic Carbonaceous Nanocomposite for Phenol Degradation

Degradation efficiency and catalyst stability are crucial issues in the control of organic compounds in wastewater by advanced oxidation processes (AOPs). However, it is difficult for catalysts used in AOPs to have both high catalytic activity and high stability. Combined with the excellent activity of cobalt/copper oxides and the good stability of carbon, highly dispersed cobalt-oxide and copper-oxide nanoparticles embedded in carbon-matrix composites (Co-Cu@C) were prepared for the catalytic activation of peroxymonosulfate (PMS). The catalysts exhibited a stable structure and excellent performance for complete phenol degradation (20 mg L-1) within 5 min in the Cu-Co@C-5/PMS system, as well as low metal-ion-leaching rates and great reusability. Moreover, a quenching test and an EPR analysis revealed that ·OH, O2·-, and 1O2 were generated in the Co-Cu@C/PMS system for phenol degradation. The possible mechanism for the radical and non-radical pathways in the activation of the PMS by the Co-Cu@C was proposed. The present study provides a new strategy with which to construct heterostructures for environmentally friendly and efficient PMS-activation catalysts.

Insights into performance and mechanism of ZnO/CuCo2O4 composite as heterogeneous photoactivator of peroxymonosulfate for enrofloxacin degradation

In this study, we designed a plain strategy for fabrication of the novel composite ZnO/CuCo₂O₄ and applied it as catalyst for peroxymonosulfate (PMS) activation to decompose enrofloxacin (ENR) under simulated sunlight. Compared to ZnO and CuCo₂O₄ alone, the ZnO/CuCo₂O₄ composite could significantly activate PMS under simulated sunlight, resulting in the generation of more active radicals for ENR degradation. Thus, 89.2 % of ENR could be decomposed over 10 min at natural pH. Furthermore, the influences of the experimental factors, including the catalyst dose, PMS concentration, and initial pH, on ENR degradation were evaluated. Subsequent active radical trapping experiments indicated that sulfate, superoxide, and hydroxyl radicals together with holes (h⁺) were involved in the degradation of ENR. Notably, the ZnO/CuCo₂O₄ composite exhibited good stability. Only 10 % decrease in ENR degradation efficiency was observed after four runs. Finally, several reasonable ENR degradation pathways were proposed, and the mechanism of PMS activation was elucidated. This study provides a novel strategy by integrating state-of-the-art material science and advanced oxidation technology for wastewater treatment and environmental remediation.

Fabrication of chitosan-MnO2‑iridium/nanoceria supported nanoparticles: Catalytic and anti-radical activities

Chitosan capped MnO₂‑iridium nanoparticles supported on nanoceria (Ch-MnO₂-Ir/CeO₂) were fabricated by using combination of colloidal solution and metal displacement galvanic methods. The oxidative degradation of acid orange 7 in aqueous solution by activated persulfate with the as-prepared nanoparticles was studied. The resulting Ch-MnO₂-Ir/CeO₂ with S₂O₈^2-, 80 % degraded 70.06 mg/L of acid orange 7 within 100 min, while at the same time, Ch-Ir, Ch-MnO₂, and Ch-Ir-MnO₂ remained inactive. CeO₂ increased the surface of the catalyst, and also improved the reactive oxygen species site of Ch-Ir-MnO₂ through the activation of S₂O₈^2- with CeO₂. The reversible redox cycle reaction, Ce (III) ↔ Ce (IV) and strong synergistic effect of MnO₂-Ir are responsible for the remarkable catalytic performance of Ch-MnO₂-Ir/CeO₂/S₂O₈^2- system. The degradation of acid orange 7 could be significantly retarded with inorganic (NO₃^- < Cl^- < SO₄^2- < H₂PO₄^- < HCO₃^-) and organic scavengers (ethanol < tertiary butanol < benzoquinone < phenol). Ch-MnO₂-Ir/CeO₂ exhibited excellent stability and reusability. Anti-radical activity of chitosan and Ch-MnO₂-Ir/CeO₂ was evaluated with 2,2-diphenyl-1-picrylhydrazyl (DPPH) free radical. The free radical properties increase with concentration of chitosan and Ch-MnO₂-Ir/CeO₂.

Degradation of Textile Dye by Bimetallic Oxide Activated Peroxymonosulphate Process

The sulphate radical based advanced oxidation processes (AOPs) are highly in demand these days, owing to their numerous advantages. Herein, the Fe-Mn bimetallic oxide particle was used to activate peroxymonosulphate (PMS) for Rhodamine B (RhB) degradation. Three bimetallic catalysts were synthesized via the chemical precipitation method with different concentrations of metals; Fe-Mn (1:1), Fe-Mn (1:2) and Fe-Mn (2:1). The best performance was shown by Fe-Mn (2:1) system at optimized conditions; 96% of RhB was removed at optimized conditions. Scavenging experiments displayed the clear dominance of hydroxyl radical in pH 3, while sulphate radical was present in a large amount at pH 7 and 10. The monometallic Fe and Mn oxides were also synthesized to confirm the synergistic effect that was present in the bimetallic oxide system. The application of optimized condition in real textile wastewater was conducted, which revealed the system works efficiently at high concentrations of PMS and catalyst dosage.

Bicarbonate enhanced heterogeneous activation of peroxymonosulfate by copper ferrite nanoparticles for the efficient degradation of refractory organic contaminants in water

Nowadays, the treatment of residual refractory organic contaminants (ROCs) is a huge challenge for environmental remediation. In this study, a potential process is provided by copper ferrite catalyst (CuFe₂O₄) activated peroxymonosulfate (PMS, HSO₅^-) in the bicarbonate (HCO₃^-) enhanced system for efficient removal of Acid Orange 7 (AO7), 2,4-dichlorophenol, phenol and methyl orange (MO) in water. The impact of key reaction parameters, water quality components, main reactive oxygen species (ROS), probable degradation mechanism, rational degradation pathways and catalyst stability were systematically investigated. A 95.0% AO7 (C₀ = 100 mg L^-1) removal was achieved at initial pH (pH₀) of 5.9 ± 0.1 (natural pH), CuFe₂O₄ dosage of 0.15 g L^-1, PMS concentration of 0.98 mM, HCO₃^- concentration of 2 mM, and reaction time of 30 min. Both sulfate radical (SO₄^-•) and hydroxyl radical (^•OH) on the surface of catalyst were proved as the predominant radical species through radical quenching experiments and electron paramagnetic resonance (EPR) analysis. The buffer nature of HCO₃^- was partially contributed for the enhanced degradation of AO7 under CuFe₂O₄/PMS/HCO₃^- system. Importantly, according to ¹³C nuclear magnetic resonance (NMR) and EPR analysis, the positive effect of bicarbonate may be mainly attributed to the formation of peroxymonocarbonate (HCO₄^-), which may enhance the generation of ^•OH. The magnetic CuFe₂O₄ particles can be well recycled and the leaching concentration of Cu was acceptable (<1 mg L^-1). Considering the widespread presence of bicarbonate in water environment, this work may provide a safe, efficient, and sustainable technique for the elimination of ROCs from practical complex wastewater.

Copper oxides activate peroxymonosulfate for degradation of methylene blue via radical and nonradical pathways: surface structure and mechanism

A one-step hydrothermal method for preparation of copper oxides with different valences using ascorbic acid as a reducing reagent was developed for environmental remediation. The results suggested that the notable degradation performance of CuO₀ may be attributable to the abundant active sites, such as Cu or Cu-O, and was not significantly related to the Cu valence state. In contrast to direct degradation of pollutants by traditional superoxide radicals (O₂^•-), O₂^•- played an important role in the reduction of high-valence Cu ions (Cu(III)). In addition, a series of radical quenching, electron paramagnetic resonance (EPR), and electrochemical experiments validated the existence of direct electron transfer between methylene blue (MB) and PMS mediated by CuO₀ and surface-bound radicals. The results suggested that the CuO₀/PMS system may be less susceptible to diverse ions and natural organic matter other than dihydrogen phosphate anions. The mechanism of MB degradation under alkaline conditions was different from that under acidic conditions in that it was not reliant on radicals or charge transfer but direct oxidation by PMS. This study provides new insights into the heterogeneous processes involved in PMS activation by the copper oxides. Furthermore, this paper devotes to providing theoretical basis on pollutant removal via PMS activated by copper oxides and developing low-cost and high-efficiency catalysts.

Electrically supported mediator Co(II)-activated peroxydisulfate synergistic process for organic contaminants elimination

Among homogeneous catalysts, cobalt ions exhibit ultra-high persulfate activation performance. In this work, an electrically supported medium Co(II) activated peroxydisulfate synergistic process was established to eliminate organic contaminants in water. The synergistic catalytic effect was verified by comparing the oxidative degradation performance and reaction rate constant of different coupling systems. The decolorization ability of E-Co(II)-PDS on reactive black 5 (RB5) was explored, and the results showed that the removal rate of RB5 can reach 93.21% under the optimized conditions of current density of 5.71 mA/cm², initial pH of 4, Co(II) concentration of 0.2 mM and PDS concentration of 5 mM. The effect of water matrix on the removal of RB5 was studied, and it was found that HCO₃^- and humic acid significantly inhibited the degradation of RB5, while Cl^- and H₂PO₄^- could effectively promote it at a certain concentration. Notably, the degradation of RB5 in E-Co(II)-PDS system achieved lower energy consumption, with an energy consumption per unit volume (EE/O) value of 0.4304 kWh·m^-3. EPR test, quenching experiments and contribution rate analysis showed that the oxidation active species in E-Co(II)-PDS process were Co(III), sulfate radicals and hydroxyl radicals, and their oxidation contribution rates were 15.72%, 12.69% and 53.25%, respectively. Finally, the decomposition process of RB5 was proposed by the mass spectrometry results. The electric current promotes cobalt ion cycling and PDS activation through electron transfer, and induces Co(II) to promote the activation of PDS, which is the main mechanism of E-Co(II)-PDS system to achieve the robust degradation ability of RB5.

Understanding the nonradical activation of peroxymonosulfate by different crystallographic MnO2: The pivotal role of MnIII content on the surface

Manganese oxide-activated persulfate plays a critical role in water purification and in situ chemical oxidation processes, but the underlying mechanism needs to be further revealed. Herein, the detailed mechanism of MnO₂ with various crystallographic structures (α-, β-, γ-, and δ-MnO₂) towards peroxymonosulfate (PMS) activation was investigated. PMS activated by tunnel structured α-, β-, and γ-MnO₂ showed higher acetaminophen (ACE) removal than layer structured δ-MnO₂ with the removal efficiency following an order of α-MnO₂ (85%) ≈ γ-MnO₂ (84%) > β-MnO₂ (65%) > δ-MnO₂ (31%). Integrated with chemical quenching experiments, electron paramagnetic resonance, Raman spectra, X-ray photoelectron spectroscopy, and Langmuir-Hinshelwood model on kinetic data, both surface-bound PMS complexes and direct oxidation by surface manganese species (Mn^{(Ⅳ, Ⅲ)}_(s)) were disclosed as the dominant oxidation mechanism for ACE degradation in α-, β-, and γ-MnO₂/PMS, which were rarely observed in previous reports. Moreover, the catalytic activity of α-, β-, and γ-MnO₂ was positively correlated to the Mn^III_(s) content on the catalyst surface. Higher content of Mn^III_(s) would stimulate the generation of more oxygen vacancies, which was conducive to the adsorption of PMS and the formation of reactive complexes. Overall, this study might provide deeper insight into the nonradical activation mechanism of PMS over different crystallographic MnO₂.

Application of pier waste sludge for catalytic activation of proxy-monosulfate and phenol elimination from a petrochemical wastewater

This investigation aimed to remove phenol from real wastewater (taken from a petrochemical company) by activating peroxy-monosulfate (PMS) using catalysts extracted from pier waste sludge. The physical and chemical properties of the catalyst were evaluated by FE-SEM/EDS, XRD, FTIR, and TGA/DTG tests. The functional groups of O-H, C-H, CO₃^2-, C-H, C-O, N-H, and C-N were identified on the catalyst surface. Also, the crystallinity of the catalyst before and after reaction with petrochemical wastewater was 103.4 nm and 55.8 nm, respectively. Operational parameters of pH (3-9), catalyst dose (0-100 mg/L), phenol concentration (50-250 mg/L), and PMS concentration (0-250 mg/L) were tested to remove phenol. The highest phenol removal rate (94%) was obtained at pH=3, catalyst dose of 80 mg/L, phenol concentration of 50 mg/L, PMS concentration of 150 mg/L, and contact time of 150 min. Phenol decomposition in petrochemical wastewater followed the first-order kinetics (k> 0.008 min^-1, R²> 0.94). Changes in pH factor were very effective on phenol removal efficiency, and maximum efficiency (≈83%) was achieved in pH 3. The catalyst stability test was performed for up to five cycles, and phenol removal in the fifth cycle was reduced to 42%. Also, the energy consumption in this study was 77.69 kW h/m³. According to the results, the pier waste sludge catalyst/PMS system is a critical process for eliminating phenol from petrochemical wastewater.

Effects of foreign metal doping on the step-by-step oxidation process in M-OMS-2 catalyzed activation of PMS

Various metal cations M (M = Mg²⁺, Ca²⁺, Zn²⁺, Cu²⁺, Fe³⁺) were doped into the tunnel of manganese octahedral molecular sieve (OMS-2). Redox-inactive metal (Ca, Mg and Zn) doped OMS-2 exhibited better peroxymonosulfate (PMS) catalytic activity than redox metal-doped Cu-OMS-2 and Fe-OMS-2. Redox-inactive metals doping improves the conductivity and reducibility of the catalyst, while transition metal doping reduces the dispersion of manganese. More importantly, the degradation of ACE can be divided into two stages. In the first stage, ACE was oxidized dominantly through mediated electron transfer process. Subsequently, singlet oxygen (¹O₂) gradually dominated oxidative degradation in the second stage, which was derived from the reaction between superoxide radical (O₂^•-) and metastable manganese intermediates. The long half-life of O₂^•- on the surface of OMS-2 ensured the delay generation of ¹O₂. This study not only provides a new idea for improving the efficiency of heterogeneous catalysts activation of PMS, but also meaningful for the in-depth study of multiple reaction mechanisms in PMS activation processes.

Vital Role of Synthesis Temperature in Co–Cu Layered Hydroxides and Their Fenton-like Activity for RhB Degradation

Cu and Co have shown superior catalytic performance to other transitional elements, and layered double hydroxides (LDHs) have presented advantages over other heterogeneous Fenton catalysts. However, there have been few studies about Co–Cu LDHs as catalysts for organic degradation via the Fenton reaction. Here, we prepared a series of Co–Cu LDH catalysts by a co-precipitation method under different synthesis temperatures and set Rhodamine B (RhB) as the target compound. The structure-performance relationship and the influence of reaction parameters were explored. A study of the Fenton-like reaction was conducted over Co–Cu layered hydroxide catalysts, and the variation of synthesis temperature greatly influenced their Fenton-like catalytic performance. The Co–Cut=65°C catalyst with the strongest LDH structure showed the highest RhB removal efficiency (99.3% within 30 min). The change of synthesis temperature induced bulk-phase transformation, structural distortion, and metal–oxygen (M–O) modification. An appropriate temperature improved LDH formation with defect sites and lengthened M–O bonds. Co–Cu LDH catalysts with a higher concentration of defect sites promoted surface hydroxide formation for H2O2 adsorption. These oxygen vacancies (Ovs) promoted electron transfer and H2O2 dissociation. Thus, the Co–Cu LDH catalyst is an attractive alternative organic pollutants treatment.

Mechanism of peroxymonosulfate activation and the utilization efficiency using hollow (Co, Mn)3O4 nanoreactor as an efficient catalyst for degradation of organic pollutants

Development of efficient catalysts for peroxymonosulfate (PMS) activation and further understanding its mechanism on organic pollutants degradation is of significant importance for advanced oxidation processes (AOPs). Herein, hollow (Co, Mn)₃O₄ catalysts were synthesized by calcination of Co, Mn containing metal-organic frameworks (MOFs) and further used to evaluate the effectiveness of organic pollutants (Bisphenol A (BPA), atrazine (ATZ), and diethyl phthalate (DEP)) degradation by PMS activation. The PMS utilization efficiency in (Co, Mn)₃O₄/PMS system (36.4%) was estimated to be 28.0% and 43.8% higher than that of Co₃O₄/PMS and Mn₅O₈/PMS system, respectively. Notably, the metal leaching in (Co, Mn)₃O₄/PMS system was significantly suppressed. The utilization efficiency also reveals an inverse proportionality relationship with BPA mineralization but decreases with increasing initial pH value. A synergy between oxides of Co and Mn was perceived to enhance PMS utilization efficiency and BPA degradation. The results indicate enhanced catalytic performance with (Co, Mn)₃O₄ compared to Co₃O₄ derived from Co-MOF and other reported catalysts, with 99% of BPA degradation within 4 min. The oxidation mechanism was then proposed based on the electron paramagnetic resonance (EPR) and XPS results. Our findings might have contributed to designing heterogeneous catalysts for efficient PMS utilization in AOPs.

Enhancement strategies for efficient activation of persulfate by heterogeneous cobalt-containing catalysts: A review

As a clean and efficient technology for the degradation of organic contaminants, sulfate radical based advanced oxidation processes (SR-AOPs) have attracted more and more attention in the past decades. Cobalt is regarded as the most reactive and efficient non-noble metal catalyst for the activation of persulfate including peroxymonosulfate (PMS) and peroxydisulfate (PDS) to produce sulfate radicals. Due to the limitations of homogeneous catalytic systems, the heterogeneous cobalt-containing catalysts have been emerged and rapidly developed. Various strategies have been schemed to further enhance the activation ability of persulfate by heterogeneous cobalt-containing catalysts. This paper provides an overview on the recent progress in enhancement strategies for the highly efficient activation of persulfate by heterogeneous cobalt-containing catalysts. With a brief introduction on the chemistry and feature of sulfate radical reactions catalyzed by homogeneous Co²⁺/Co³⁺ species, the main strategies for enhancing persulfate activation by heterogeneous cobalt-containing catalysts are summarized, such as surface and morphology design, multiple reactive centers design, organic-inorganic hybrids and heterostructure composites. Future perspectives of heterogeneous SR-AOPs systems catalyzed by cobalt-containing catalysts are outlined.

Activation of O2 by zero-valent zinc assisted with Cu(II) for organics removal: Performance and mechanism

This study proposes a method to activate O₂ by accelerating the corrosion process for zero-valent zinc (ZVZ) with the assistance of Cu(II), promoting the consecutive production of reactive oxygen species. The mechanisms for reactive oxygen species generation are clarified with metronidazole (MTZ) as the targeted pollutant. The outcome suggests the association of Cu(Ⅱ) and ZVZ presents an apparent cooperative activity, an enhancement of 85% in MTZ removal is attained for the ZVZ/Cu(Ⅱ) system after 10 min compared to that for ZVZ. Analysis of the mechanisms involved indicates that this improvement is due to the addition of Cu(Ⅱ), which can accelerate the corrosion of ZVZ. In addition, quenching experiments and electron paramagnetic resonance (EPR) technology show that superoxide radicals (·O₂^-) result in rapid MTZ degradation. The primary component that is liable for O₂ activation and a certain amount of H₂O₂ generation is verified to be ZVZ. Moreover, Cu(I) is detected in the ZVZ/Cu(Ⅱ) system, which arises from a direct reduction pathway driven by ZVZ and an indirect reduction pathway driven by active hydrogen atoms.

Synergistic oxygen vacancy-rich CuO/visible light activation of peroxymonosulfate for degradation of rhodamine B: fast catalyst synthesis and degradation mechanism

This work outlines the synthesis of copper oxide nanoparticles (CuO-SC) loaded with a number of oxygen vacancies by a fast sodium citrate assisted precipitation method with no need of calcination. X-ray diffraction, scanning electron microscopy, UV-Vis diffuse reflectance spectroscopy, time-resolved fluorescence lifetime and electrochemical impedance spectra were used to characterize the as-synthesized nanocomposites. The results indicated that the CuO-SC nanoparticles had regular fusiform shape with high surface area, wide light harvesting window, fast charge transport and high carrier concentration. As a result, the catalytic activity of the CuO-SC/peroxymonosulfate (PMS)/visible light (Vis) system for the degradation of rhodamine B (RhB) was much higher than that of as-prepared CuO nano powder in the absence of sodium citrate. Almost 98.0% of the initial RhB dyes was decomposed in 20 min with 0.12 g L⁻¹ PMS and 0.3 g L⁻¹ catalyst. Meantime, it exhibited high catalytic stability with little deactivation after four runs and a wide application range of pH. Moreover, RhB can be readily degraded with backgrounds of Cl⁻, NO₃⁻, SO₄²⁻, HCO₃⁻ and low concentration of humic acid in a CuO-SC/PMS/Vis system. Combined with the results of electron spin resonance paramagnetic spectroscopy, X-ray photoelectron spectroscopy and radical quenching experiments, holes, superoxide radicals and a small amount of sulfate radicals, hydroxyl radicals and singlet oxygen were involved in the CuO-SC/PMS/Vis system. Furthermore, a possible degradation mechanism based on the synergistic effect of radical reaction and non-radical reaction was proposed based on the above results.

Oxygen vacancy-rich CuO nanoparticles synthesized via a sodium citrate strategy exhibit extremely excellent visible light-assisted catalytic behavior.

A novel CoNi7O8/MnO2 nanocomposite supported on Ni foam as a peroxymonosulfate activator for the highly efficient singlet oxygen mediated removal of methylene blue

Novel CoNi7O8/MnO2 supported on Ni foam presented excellent catalytic activity toward PMS activation, with 100% MB removal achieved within 15 min.

Degradation of tetrabromobisphenol A through peroxymonaosulfate oxidation activated by La0.5Sr0.5CoxMn1-xO3-δ perovskite

La_0.5Sr_0.5Co_xMn_1-xO_3-δ (LSCM) perovskite composite oxides prepared by co-doping of Co and Mn in B site-activated peroxymonosulfate (PMS) to degrade tetrabromobisphenol A. The characterization results indicated that the LSCM with x=0.3-0.8 have hexagonal R-3c structure. The activation effect of LSCM on PMS decreased gradually with the increase of Mn doping, among which LSCM82 (x=0.8) had good oxygen desorption performance certificated by O₂-TPD and lower relative acidity (1.975). Moreover, the redox pairs of Co/Mn multi-valence ions were the main contributor to its catalytic activity. The electron spin resonance results suggested that SO₄^•- and •OH existed in the system and SO₄^•- is the main free radical. Therefore, LSCM82 perovskite catalyst has broad application prospects in aqueous solutions.

Sunlight-induced photocatalytic degradation of organic pollutants by biosynthesized hetrometallic oxides nanoparticles

Dyes and phenols are extensively used chemicals in petrochemicals, pharmaceuticals, textile, and paints industries. Due to high persistence, bioaccumulation, and toxicity, their removal from the environment is highly imperative by advanced techniques. Single metal oxide nanomaterials are generally associated with limitations of large bandgap (> 3eV) and charge recombination. Therefore, heterometallic oxides (HMOs) as CuFe₂O₄, CuMn₂O₄, and MnZn₂O₄ have been synthesized via green route by employing leaf extract of Azadirachta indica. XRD revealed the crystalline nature of HMOs nanospheres with particle size less than 100 nm. Subsequently, HMOs nanocatalysts were used as photocatalyst for removal of 3-amino phenols (3-AP) and eriochrome black T (EBT) from water under sunlight. Reaction parameters namely pollutant concentration (50-130 mgL^-1), catalyst dose (20-100 mg), and pH (3-11) were optimized in order to get best results. Substantial degradation (80-95%) of pollutants (50 mgL^-1) by HMOs (80 mg) was achieved at neutral pH under sunlight exposure. Highest removal by CuFe₂O₄ might be due to its high surface area (35.7 m²g^-1), low band gap (2.4 eV), larger particle stability (Zeta potential: -22.0 mV), and lower photoluminescence intensity. Sharp declines in curves were visually confirmed by color change and indicated for first-order kinetics of degradation with initial Langmuir adsorption. Spectrophotometric analysis revealed that half-life (t_1/2) of 3-AP (0.9-1.7 h) and EBT (0.6-0.8 h) were significantly reduced. Faster degradation of EBT than 3-AP was because of less electronegative N-atom at the diazo group. Scavenger analysis indicated the presence of active radicals in photo-catalytic degradation of 3-AP and EBT. All HMOs have shown high reusability (n=8) which ensures their stability, sustainability, and efficiency. Overall, green synthesized HMOs nanoparticles with prominent surface characteristics offer a viable alternative photocatalyst for industrial applications.

Photocatalytic activation of peroxymonosulfate (PMS) by novel mesoporous Ag/ZnO@NiFe2O4 nanorods, inducing radical-mediated acetaminophen degradation under UVA irradiation

A new mesoporous Ag/ZnO@NiFe₂O₄ nanorod was prepared by a facile, low-cost, and environmentally friendly strategy from a bimetallic Fe₂Ni-MIL-88 metal organic framework (MOF), as an effective catalyst and peroxymonosulfate (PMS) photo-activator. The structural, morphological, optical, and magnetic properties, as well as the material composition were investigated by XRD, FE-SEM, EDX, HR-TEM, XPS, DRS, PL, EIS, VSM, N₂ adsorption-desorption and ICP-AES analysis. 1.0% w/w loading of Ag nanoparticles on ZnO_0.04@NiFe₂O₄ led to the best catalytic activity for PMS activation under UVA in acetaminophen (ACT) degradation. The maximum degradation efficiency for ACT was 100% within 15 min (at pH = 7.0), with a first-order rate constant of 0.368 min^-1. The calculated quantum yield (1.3 × 10^-3 molecule/photon) of the optimum catalyst was 2.05, and 5.63 times higher than its simple constituents, ZnO_0.04@NiFe₂O₄ and NiFe₂O₄, respectively. Among the various inorganic ions, Cl^- and HCO₃^- showed significant inhibition effect in 1.0%w/w Ag/ZnO_0.04@NiFe₂O₄/PMS/UVA system, due to radical quenching effects. Based on scavenger experiments, HO^• and SO₄^•- were the dominant reactive species in photocatalytic process coupled with PMS. Due to presence of the Fe³⁺/Fe²⁺, and Ni²⁺/Ni³⁺ reaction cycles in the as-made catalyst, the reaction rate of PMS activation was greatly enhanced. Moreover, the formation of a hetero-junction structure with NiFe₂O₄ and ZnO promoted the charge separation of the photo-generated electron/hole pairs. Finally, the major intermediates produced during the reaction were detected by LC-MS analysis, and a plausible mechanism for the photocatalytic degradation of ACT was proposed and discussed in detail.

Synthesis of novel erdite nanorods for the activation of peroxymonosulfate during p-nitrophenol wastewater treatment

Fe-bearing salt and minerals are common reagents used in activating peroxymonosulfate (PMS) for Fenton-like oxidation in wastewater treatment. Fe-bearing reagents are used in mass production, which generate abundant Fe-bearing waste sludge in the absence of a reductant for Fe³⁺/Fe²⁺ cycling. Herein, a novel Fe/S-bearing mineral, erdite, was synthesized with a one-step hydrothermal route. The material exerted an Fe/S synergetic effect for p-nitrophenol degradation upon PMS activation and showed a one-dimensional structure similar to that of (FeS₂)_n^n-. It contained short rods with diameters of 100 nm and lengths ranging from 200 to 400 nm. It grew radically to 0.8-2 μm in length upon the addition of MnO₂. Ps-0.5, prepared by adding MnO₂ in an Mn/Fe molar ratio of 0.5, showed optimal efficiency in removing approximately 99.4% of p-nitrophenol upon PMS activation. Only 3.3% of p-nitrophenol was removed without MnO₂. The efficiency of p-nitrophenol removal through Ps-0.5 activation was higher than that through FeSO₄, nanoscale zero-valent iron (nZVI), CuFeS₂, and MnSO₄ activation. The formed erdite rods were spontaneously hydrolyzed to Fe/S-bearing flocs, in which an electron was used by structural S to reduce Fe³⁺ to Fe²⁺ upon PMS activation. The reduction resulted in a high p-nitrophenol removal rate. This study provided new insight into the development of an effective PMS activator in wastewater treatment.

An innovative, highly stable Ag/ZIF-67@GO nanocomposite with exceptional peroxymonosulfate (PMS) activation efficacy, for the destruction of chemical and microbiological contaminants under visible light

In this work, Ag nanoparticles were loaded on ZIF-67 covered by graphene oxide (Ag/ZIF-67@GO), and its catalytic performance was studied for the heterogeneous activation of peroxymonosulfate (PMS) under visible-light. The catalyst surface morphology and structure were analyzed by FT-IR, XRD, XPS, DRS, FE-SEM, EDX, TEM, BET, ICP-AES and TGA analysis. The efficacy of PMS activation by the Ag/ZIF-67@GO under visible light was assessed by phenol degradation and E. coli inactivation. Phenol was completely degraded within 30 min by HO^•, SO₄^•- and O₂^•- generated through the photocatalytic PMS activation. In addition, total E. coli inactivation was attained in 15 min that confirmed the highly efficient catalytic activation of PMS by the as-made nanocomposite under visible light. The reaction mechanism was elucidated and the importance of the generated reactive species followed the order of: HO^• > SO₄^•- > O₂^•- > h⁺, implying a radical-pathway dominated process.

Efficient activation of peroxymonosulfate by Co-doped mesoporous CeO2 nanorods as a heterogeneous catalyst for phenol oxidation

Sulfate radical-based advanced oxidation processes have received considerable attentions in the remediation of organic pollutants due to their high oxidation ability. In this study, a novel Co3O4/CeO2 catalyst was fabricated and employed as a peroxymonosulfate (PMS) activator to generate SO4•- for phenol degradation. The Co3O4/CeO2 catalyst exhibited a good catalytic performance at a wide pH range of 3.4 to 10.8, and 100% phenol (20 mg/L) was removed within 50-min reaction under optimal conditions with 0.2 g/L catalyst and 2.0 g/L PMS at room temperature. The transformation products and total organic carbon during the degradation process were also determined. The quenching experiments and electron paramagnetic resonance spectra revealed that sulfate radical (SO4•-) rather than other species such as singlet oxygen (1O2) and hydroxyl radical (•OH) was primarily responsible for phenol degradation in the Co3O4/CeO2/PMS system, and a rational mechanism was proposed. Moreover, the recycling experiments as well as low cobalt leaching concentration manifested satisfactory reusability and stability. The effects of various inorganic anions and natural organic matter in real water matrix on phenol oxidation were further evaluated. We believe that the Co3O4/CeO2 composites have promising applications of PMS activation for the degradation of organic pollutants in wastewater treatment.

Recent advances in cobalt-activated sulfate radical-based advanced oxidation processes for water remediation: A review

Sulfate radical-based advanced oxidation processes (SR-AOPs) have attracted increasing attention for the degradation of organic contaminants in water. The oxidants of SR-AOPs could be activated to generate different kinds of reactive oxygen species (ROS, e.g., hydroxyl radicals (OH), sulfate radicals (SO₄^-), singlet oxygen (¹O₂), and superoxide radicals (O₂^-)) by various catalysts. As one of the promising catalysts, cobalt-based catalysts have been extensively investigated in catalytic activity and stability during water remediation. This article mainly summarizes recent advances in preparation and applications of cobalt-based catalysts on peroxydisulfate (PDS)/peroxymonosulfate (PMS) activation since 2016. The review covers the development of homogeneous cobalt ions, cobalt oxides, supported cobalt composites, and cobalt-based mixed metal oxides for PDS/PMS activation, especially for the latest nanocomposites such as cobalt-based metal-organic frameworks and single-atom catalysts. This article also discussed the activation mechanisms and the influencing factors of different cobalt-based catalysts for activating PDS/PMS. Finally, the future perspectives on the challenges and applications of cobalt-based catalysts are presented at the end of this paper.

Degradation of antibiotics in aqueous media using manganese nanocatalyst-activated peroxymonosulfate

ε-MnO₂ effectively activates peroxymonosulfate (PMS) for the efficient degradation of emerging pollutants. ε-MnO₂ was synthesized by a facile thermal-treatment method and its long-term stability and efficiency for the elimination of emerging pollutants, including sulfamethoxazole (SMX), sulfachloropyridazine (SCP), sulfamethazine (SMT), ciprofloxacin (CIP), and azithromycin (AZI), from aqueous media were evaluated. ε-MnO₂ was found to activate PMS more efficiently than α-MnO₂, β-MnO₂, or δ-MnO₂, owing to its high - OH-group content, unique structure, and high surface area. Sulfate (SO₄^•-), hydroxyl (•OH), and superoxide (O₂^•-) radicals, as well as singlet oxygen (¹O₂) were generated, with O₂^•- acting as the ¹O₂ precursor. The ε-MnO₂/PMS system proved to be effective in the pH range of 3.5-9.0 and the rate of SMX degradation was not significantly affected by the presence of inorganic anions or natural organic matter. The proposed pathway for the activation of PMS by ε-MnO₂ includes inner-sphere interactions between ε-MnO₂ and PMS, and electron transfer to PMS via the MnIII ↔ MnIV redox cycle, which generates reactive oxygen species. These findings provide new insight into PMS activation by less-toxic metal oxides as catalysts and demonstrate that Mn-based materials can be used to effectively treat water matrices containing emerging pollutants.

UV Stimulated Manganese Dioxide for the Persulfate Catalytic Degradation of Bisphenol A

One of the most commonly produced industrial chemicals worldwide, bisphenol A (BPA), is used as a precursor in plastics, resins, paints, and many other materials. It has been proved that BPA can cause long-term adverse effects on ecosystems and human health due to its toxicity as an endocrine disruptor. In this study, we developed an integrated MnO2/UV/persulfate (PS) process for use in BPA photocatalytic degradation from water and examined the reaction mechanisms, degradation pathways, and toxicity reduction. Comparative tests using MnO2, PS, UV, UV/MnO2, MnO2/PS, and UV/PS processes were conducted under the same conditions to investigate the mechanism of BPA catalytic degradation by the proposed MnO2/UV/PS process. The best performance was observed in the MnO2/UV/PS process in which BPA was completely removed in 30 min with a reduction rate of over 90% for total organic carbon after 2 h. This process also showed a stable removal efficiency with a large variation of pH levels (3.6 to 10.0). Kinetic analysis suggested that 1O2 and SO4•− played more critical roles than •OH for BPA degradation. Infrared spectra showed that UV irradiation could stimulate the generation of –OH groups on the MnO2 photocatalyst surface, facilitating the PS catalytic degradation of BPA in this process. The degradation pathways were further proposed in five steps, and thirteen intermediates were identified by gas chromatography-mass spectrometry. The acute toxicity was analyzed during the treatment, showing a slight increase (by 3.3%) in the first 30 min and then a decrease by four-fold over 2 h. These findings help elucidate the mechanism and pathways of BPA degradation and provide an effective PS catalytic strategy.

New insights into the mechanisms of tartaric acid enhancing homogeneous and heterogeneous copper-catalyzed Fenton-like systems

The specific roles of tartaric acid (TA), as an eco-friendly ligand, in homogeneous and heterogeneous copper-catalyzed systems were systematically revealed and new mechanisms of TA enhancing the three Fenton-like processes were proposed to provide a theoretical significance in overcoming the deficiency of conventional Fenton processes. The results identified hydroxyl radical (•OH) as the main species responsible for the simultaneous decomposition of TA and metronidazole (MNZ) according to TOC removal. The ESR technique was used to detect superoxide radicals (•O₂^-), carbon-centered radical (•R) and hydrogen radical (•H) in the Cu²⁺/TA/H₂O₂ system, which contributed to the acceleration of the Cu²⁺/Cu⁺ redox cycle. The enhancing effect of TA on the homogeneous process was ascribed to the formation of a soluble complex with Cu²⁺, which favored the pH range extension, Cu⁺ oxidation, and radical generation. Moreover, the adsorption of TA on the catalysts surface promoted the consumption of H₂O₂, inducing •OH generation. The formed surface complex (≡Cu²⁺-TA) also accelerated the regeneration of ≡Cu⁺, which was confirmed by density functional theory (DFT) calculation and surface characterization analysis (SEM, XRD, and XPS). The possible degradation pathways of MNZ in TA-modified Fenton-like system were also clarified.

Recycling application of modified waste electrolytic manganese anode slag as efficient catalyst for PMS activation

Electrolytic manganese anode slag (EMAS) is the waste residue produced by electrolytic manganese metal industry. At present, no mature recycling system has been established, which causes a waste of resources and threatens the environment. Therefore, the resource utilization of EMAS has attracted increased attention. In this paper, the in-situ resource utilization of EMAS can be realized by pickling treatment was reported. Specifically, EMAS after pickling treatment (PEMAS) was first used as catalyst to activate PMS to degrade tetrachlorophenol (4-CP). Pickling could remove the inert inorganic components on EMAS and increase the specific surface area, pore volume and Mn distribution of the catalyst, thus improving the catalytic performance of the catalyst. Under the conditions of 4-CP of 40 ppm, PMS of 1 mM and PEMAS of 0.3 g L^-1, 85% of 4-CP could be degraded within 50 min. Mechanism studies proved that the main active species were O₂^- and ¹O₂. Some O₂^- contributed to the generation of ¹O₂ and some O₂^- directly contributed to the degradation of 4-CP. During the reaction, the valence state of Mn transformed between Mn(III)/Mn(IV) and Mn(II)/Mn(III) and kept the cycle. Moreover, PEMAS/PMS system exhibited excellent independence of the solution pH, resistance to the versatile inorganic ions and background organic matters, and stability of recycling. In a word, this study has achieved the resource utilization of EMAS and the goal of treating waste with waste, which is a win-win strategy of economic and environmental benefits.

High performance of the A-Mn2O3 nanocatalyst for persulfate activation: Degradation process of organic contaminants via singlet oxygen

In this study, the catalytic activation of persulfate (PS) via metal oxides was investigated, and the A-Mn₂O₃ nanocatalyst was found to have the highest efficiency among other PS activators for the degradation of organic contaminants. Additionally, A-Mn₂O₃ exhibited a remarkable efficiency in activating PS for the degradation of phenol compared to both B-Mn₂O₃ and C-Mn₂O₃. This was attributed to the longer bonds between edge-sharing MnO₆ octahedra, the unique structure, the high content surface -OH groups, and the average oxidation states. This indicated that all these properties played an important role in an efficient PS activation. Electron paramagnetic resonance (EPR) spectroscopy, scavenger tests, and chemical probes were conducted to investigate the reactive oxygen species (ROS). Singlet oxygen (¹O₂) was determined to be the main ROS generated from PS activation. A plausible mechanism study was proposed, which involved inner-sphere interactions. An electron transfer of the Mn species facilitated the decomposition of PS to generate HO₂^•/O₂^{• -} radicals, which were utilized as a precursor for ¹O₂ generation via direct oxidation or the recombination of HO₂^•/O₂^{• -}. Finally, the phenol and Sulfachloropyridazine (SCP) degradation pathways were proposed by ¹O₂ over the A-Mn₂O₃/PS system according to HPLC and LC-MS results.

Heterogeneous catalytic oxidation degradation of BPAF by peroxymonosulfate active with manganic manganous oxide: Mineralization, mechanism and degradation pathways

In this study, the catalytic ability and mechanisms involved in activating peroxymonosulfate (PMS) with Mn₃O₄ and the degradation pathways of bisphenol-AF (BPAF) removal was investigated. SO₄^-• and ·OH which were explored by and scavenging tests were the major reactive radicals in the Mn₃O₄/PMS system. A simple simulation algorithm was also used to calculate the relative concentrations of SO₄^-• ([SO₄^-•]) and ·OH ([·OH]) which were 8.39 × 10 ^-15 M and 6.96 × 10 ^-13 M, respectively. The mechanism for the electron transfer between the Mn (II) and Mn (III) species was discussed. Three degradation pathways of BPAF were determined by the GC/MS and LC/MS technology, including chemical mechanism of oxidation, hydroxylation, electron transfer, polymerization, and ring-cleavage. In addition, the results suggested that the Mn₃O₄/PMS system had an efficient total organic carbon (TOC) removal rate and excellent environmental adaptability, the removal rate of TOC being as high as 73.2% in the control condition. Furthermore, the reuse experiments and the comparison on the structural and componential changes of Mn₃O₄ powder before and after reaction demonstrated that the Mn₃O₄ catalyst possessed excellent stability and reusability. Finally, a maximum BPAF degradation of approximately 90.0% was achieved on the optimal conditions for 500 mg/L Mn₃O₄ dosage, 4 mM PMS concentration, 7.0 ± 0.2 initial pH, and 5 mg/L BPAF concentration respectively. And the effect of the coexisting anions and natural environmental water quality were also considered. This study demonstrated the Mn₃O₄/PMS system can be considered as a green approach for the removal of environmental reluctant pollutants.

Synthesis and catalytic utilization of bimetallic systems for wastewater remediation: A review

The environment is affected by agricultural, domestic, and industrial activities that lead to drastic problems such as global warming and wastewater generation. Wastewater pollution is of public concern, making the treatment of persistent pollutants in water and wastewater highly imperative. Several conventional treatment technologies (physicochemical processes, biological degradation, and oxidative processes) have been applied to water and wastewater remediation, but each has numerous limitations. To address this issue, treatment using bimetallic systems has been extensively studied. This study reviews existing research on various synthesis methods for the preparation of bimetallic catalysts and their catalytic application to the treatment of organic (dyes, phenol and its derivatives, and chlorinated organic compounds) and inorganic pollutants (nitrate and hexavalent chromium) from water and wastewater. The reaction mechanisms, removal efficiencies, operating conditions, and research progress are also presented. The results reveal that Fe-based bimetallic catalysts are one of the most efficient heterogeneous catalysts for the treatment of organic and inorganic contamination. Furthermore, the roles and performances of bimetallic catalysts in the removal of these environmental contaminants are different.

In situ synthesis of a hybrid Fe(Co)/MXene/ZSM-5 catalyst for phenol abatement

MXene (Ti3C2) was introduced to develop the multifunctional photocatalyst Metal/MXene/ZSM-5 to enhance the catalytic efficiency of the ZSM-5 based catalyst.

Mechanism insight into efficient peroxydisulfate activation by novel nano zero-valent iron anchored yCo3O4 (nZVI/yCo3O4) composites

Novel nano zero-valent iron anchored bio-matrix supported Co₃O₄ (nZVI/yCo₃O₄) composites were fabricated for tetracycline (TC) efficient degradation by activating peroxydisulfate (PS). The systematical characterizations verified that the nZVI/yCo₃O₄ composites with magnetism have higher surface area than yCo₃O₄ and pure Co₃O₄, contributing to more accessible active sites. Various catalytic parameters (nZVI mass ratio, leached ions, initial pH, catalyst dosage, PS concentration and coexisting anions) were thoroughly investigated. In nZVI/yCo₃O₄/PS system, 97.6 %, 93.4 % and 77.3 % TC were degraded within 15 min at pH 3.0, 6.0 and 9.0, respectively. Based on four successive degradation runs, the excellent mineralization rate and reusability of nZVI/yCo₃O₄ composites were mainly benefited from the suppressed metals leaching. The PS activated mechanisms were proposed as non-radicals (¹O₂) dominated pattern at acidic conditions and radicals (SO₄-) predominant pattern at alkaline environment, which may be highly related to the electron donating capacity of nZVI at different pH and the M^(n + 1)+/Mⁿ⁺ redox cycling between Fe or Co metal. The plausible degradation routes of TC were presented based on the detected intermediates. Overall, the synthesized heterogeneous nZVI/yCo₃O₄ composites can efficiently active PS at a wide pH range, and further broaden the application of Co-based catalysts in PS activation.