Removal of the heavy metal ion nickel (II) via an adsorption method using flower globular magnesium hydroxide

A hybrid system for Nickel ions removal from synthesized wastewater using adsorption assisted with electrocoagulation

The presence of heavy metal ions in water environments has raised significant concerns, necessitating practical solutions for their complete removal. In this study, a combination of adsorption and electrocoagulation (ADS + EC) techniques was introduced as an efficient approach for removing high concentrations of nickel ions (Ni2+) from aqueous solutions, employing low-cost sunflower seed shell biochar (SSSB). The combined techniques demonstrated superior removal efficiency compared to individual methods. The synthesized SSSB was characterized using SEM, FT-IR, XRD, N2-adsorption-desorption isotherms, XPS, and TEM. Batch processes were optimized by investigating pH, adsorbent dosage, initial nickel concentration, electrode effects, and current density. An aluminum (Al) electrode electrocoagulated particles and removed residual Ni2+ after adsorption. Kinetic and isotherm models examined Ni2+ adsorption and electrocoagulation coupling with SSSB-based adsorbent. The results indicated that the kinetic data fit well with a pseudo-second-order model, while the experimental equilibrium adsorption data conformed to a Langmuir isotherm under optimized conditions. The maximum adsorption capacity of the activated sunflower seed shell was determined to be 44.247 mg.g-1. The highest nickel ion removal efficiency of 99.98% was observed at initial pH values of 6.0 for ADS and 4.0 for ADS/EC; initial Ni2+ concentrations of 30.0 mg/L and 1.5 g/L of SSSB; initial current densities of 0.59 mA/cm2 and 1.32 kWh/m3 were also found to be optimal. The mechanisms involved in the removal of Ni2+ from wastewater were also examined in this research. These findings suggest that the adsorption-assisted electrocoagulation technique has a remarkable capacity for the cost-effective removal of heavy metals from various wastewater sources.

Effects of magnesium hydroxide morphology on Pb(ii) removal from aqueous solutions

In this study, magnesium hydroxide (MH) particles with distinct morphologies were obtained through direct precipitation and subsequent hydrothermal treatment with various magnesium salts. The synthesized products were systematically characterized and utilized for the removal of Pb(ii) ions from aqueous solutions. The adsorption process of Pb(ii) by two different MH structures, namely flower globular magnesium hydroxide (FGMH) and hexagonal plate magnesium hydroxide (HPMH), adhered to the Langmuir isotherm and pseudo-second-order model. FGMH exhibited higher Pb(ii) removal capacity (2612 mg g-1) than HPMH (1431 mg g-1), attributable to the unique three-dimensional layered structures of FGMH that provide a larger surface area and abundant active sites. Additionally, metallic Pb was obtained by recycling the adsorbed Pb(ii) through acid dissolution-electrolysis. Furthermore, Pb(ii) removal mechanisms were investigated by analyzing adsorption kinetics and isotherms, and the adsorbed products were characterized. Based on the findings, the removal process occurs in two key stages. First, Pb(ii) ions bind with OH- ions on the surface upon diffusing to the MH surface, resulting in Pb(OH)2 deposits in situ. Concurrently, Mg(ii) ions diffuse into the solution, substituting Pb(ii) ions in the MH lattice. Second, the resultant Pb(OH)2, which is unstable, reacts with CO2 dissolved in water to yield Pb3(CO3)2(OH)2. Therefore, owing to its outstanding Pb(ii) adsorption performance and simple preparation method, FGMH is a promising solution for Pb(ii) pollution.

Resourcization of Argillaceous Limestone with Mn3O4 Modification for Efficient Adsorption of Lead, Copper, and Nickel

Argillaceous limestone (AL) is comprised of carbonate minerals and clay minerals and is widely distributed throughout the Earth's crust. However, owing to its low surface area and poorly active sites, AL has been largely neglected. Herein, manganic manganous oxide (Mn3O4) was used to modify AL by an in-situ deposition strategy through manganese chloride and alkali stepwise treatment to improve the surface area of AL and enable its utilization as an efficient adsorbent for heavy metals removal. The surface area and cation exchange capacity (CEC) were enhanced from 3.49 to 24.5 m2/g and 5.87 to 31.5 cmoL(+)/kg with modification, respectively. The maximum adsorption capacities of lead (Pb2+), copper (Cu2+), and nickel (Ni2+) ions on Mn3O4-modified argillaceous limestone (Mn3O4-AL) in mono-metal systems were 148.73, 41.30, and 60.87 mg/g, respectively. In addition, the adsorption selectivity in multi-metal systems was Pb2+ > Cu2+ > Ni2+ in order. The adsorption process conforms to the pseudo-second-order model. In the multi-metal system, the adsorption reaches equilibrium at about 360 min. The adsorption mechanisms may involve ion exchange, precipitation, electrostatic interaction, and complexation by hydroxyl groups. These results demonstrate that Mn3O4 modification realized argillaceous limestone resourcization as an ideal adsorbent. Mn3O4-modified argillaceous limestone was promising for heavy metal-polluted water and soil treatment.

Selective capture of palladium from acid wastewater by thiazole-modified activated carbon: Performance and mechanism

As a kind of scarce metal, palladium is widely used in many chemical industries. It essential to recover palladium from secondary resources, especially acidic media, owing to high content of palladium in secondary wastes and widespread extraction of palladium via strong acids. Chemically modified carbon materials not only have the advantage of activated carbon but also achieve the precise removal of specific pollutants, which is a kind of adsorption material with broad application prospects. In this direction, we report a solid carbon material named AT-C, which is obtained by one-step synthesis of 2-aminothiazoles grafted to the carbon surface by amidation. The present adsorbent delivers a high palladium adsorption capacity of 178.9 mg g-1, and desirable thermal and chemical stability. The uniform presence of abundant sulfur atoms and CO in the porous network enables AT-C to achieve selective absorption and rapid adsorption kinetics of Pd2+ in the complex water mixture containing many competing ions in the acidic pH range. For the strongly acidic leachates of catalysts, AT-C exhibits outstanding stability in cyclic experiments. Meanwhile, the fixed-bed column test indicates that 1076 bed volumes of the feeding streams can be effectively treated. In addition, AT-C exhibits superior adsorption selectivity, and the recovery efficiency of Pd2+ in actual industrial wastewater is 96.6%. This work realizes an efficient, rapid, and selective removal of palladium under acidic conditions, and provides a reference for complex industrial water treatment and resource recovery of precious metals.

Facile fabrication of Fe3O4@Mg(OH)2 magnetic composites and their application in Cu(ii) ion removal

In this study, we fabricated magnetic Fe3O4@Mg(OH)2 composites through the seed deposition technique to achieve Cu(ii) ion removal from aqueous solutions. As indicated by the characterization results, three-dimensional flower-like spheres composed of external Mg(OH)2 were formed, with nano-Fe3O4 particles uniformly embedded in the "flower petals" of the spheres. The efficacy of Fe3O4@Mg(OH)2-3 in Cu(ii) ion removal was examined through batch experiments. The impact of solution pH on removal efficiency was examined, and the pseudo-second-order model and the Langmuir model provided good fits to the adsorption kinetics and isotherm data, respectively. Remarkably, Fe3O4@Mg(OH)2-3 exhibited a significant removal capacity of 1051.65 mg g-1 for Cu(ii) ions. Additionally, the composite displayed a notable saturation magnetization value of 17.3 emu g-1, facilitating isolation from sample solutions through external magnetic fields after Cu(ii) ion absorption. At the solid-liquid interface, a mechanism involving ion exchange between Mg(ii) and Cu(ii) cations was realized as the mode of Cu(ii) ion removal. The composites' effective adsorption properties and rapid magnetic separation highlighted their suitability for use in treating copper-contaminated water.

Simultaneous removal of ammonia nitrogen, recovery of phosphate, and immobilization of nickel in a polyester fiber with shell powder and iron carbon spheres bioreactor: Optimization and pathways mechanism

Composite pollutants are prevalent in wastewater, whereas, the simultaneous accomplishment of efficient nitrogen removal and resources recovery remains a challenge. In this study, a bioreactor was constructed to contain Pseudomonas sp. Y1 using polyester fiber wrapped with shell powder and iron carbon spheres, achieving ammonia nitrogen (NH₄⁺-N) removal, phosphate (PO₄^3--P) recovery, and nickel (Ni²⁺) immobilization. The optimal performance of bioreactor was average removal efficiencies of NH₄⁺-N, PO₄^3--P, calcium (Ca²⁺), and Ni²⁺ as 82.42, 96.67, 76.13, and 98.29% at a hydraulic retention time (HRT) of 6 h, pH of 7.0, and influent Ca²⁺ and Ni²⁺ concentrations of 100.0 and 3.0 mg L^-1, respectively. The bioreactor could remove PO₄^3--P, Ca²⁺, and Ni²⁺ by biomineralization, co-precipitation, adsorption, and lattice substitution. Moreover, microbial community analysis suggested that Pseudomonas was the predominant genus and had possessed tolerance to Ni²⁺ toxicity in wastewater. This study presented an effective method to synchronously remove NH₄⁺-N, recover PO₄^3--P, and fix heavy metals through microbially induced carbonate precipitation (MICP) and heterotrophic nitrification and aerobic denitrification (HNAD) technology.

Recent Progress in Emerging Novel MXenes Based Materials and their Fascinating Sensing Applications

Early transition metals based 2D carbides, nitrides and carbonitrides nanomaterials are known as MXenes, a novel and extensive new class of 2D materials family. Since the first accidently synthesis based discovery of Ti₃ C₂ in 2011, more than 50 additional compositions have been experimentally reported, including at least eight distinct synthesis methods and also more than 100 stoichiometries are theoretically studied. Due to its distinctive surface chemistry, graphene like shape, metallic conductivity, high hydrophilicity, outstanding mechanical and thermal properties, redox capacity and affordable with mass-produced nature, this diverse MXenes are of tremendous scientific and technological significance. In this review, first we'll come across the MXene based nanomaterials possible synthesis methods, their advantages, limitations and future suggestions, new chemistry related to their selected properties and potential sensing applications, which will help us to explain why this family is growing very fast as compared to other 2D families. Secondly, problems that help to further improve commercialization of the MXene nanomaterials based sensors are examined, and many advances in the commercializing of the MXene nanomaterials based sensors are proposed. At the end, we'll go through the current challenges, limitations and future suggestions.

Preparation of esterified biomass waste hydrogels and their removal of Pb2+, Cu2+ and Cd2+ from aqueous solution

The treatment of polluted water is a serious environmental problem in the world. Biomass is easily modified and can be prepared into adsorbent materials, which is expected to solve the problem of heavy metal ion adsorption in sewage. In this paper, esterified tobacco straw based hydrogels (ETS-PAA) were synthesized from waste tobacco straw biomass. The structure and thermal stability of these hydrogels were characterized by FTIR, SEM, EDS, XPS and TG. The adsorption of metal ions by the hydrogel was measured by ICP-MS. The effects of initial ion concentration, adsorption time, pH, and temperature on the heavy metal adsorption were investigated. The results showed that ETS-PAA possessed more pores, which led to a better adsorption capacity. The maximum adsorption amounts of Pb²⁺, Cu²⁺ and Cd²⁺ were 2.41 mmol·g^-1, 1.93 mmol·g^-1 and 1.77 mmol·g^-1, respectively. Finally, the adsorption mechanism and kinetics were analyzed. The adsorption was mainly accomplished by ion exchange of -COOK on the monomer chain with heavy metal ions, coordination of -OH and -CONH with heavy metal ions and interaction of ester bond, -COOH with heavy metal ions. The adsorption process was in accordance with the pseudo-second-order kinetic model and Freundlich model. The adsorption process belonged to multilayer chemisorption. This work shows that ETS-PAA was a promising material for the removal of heavy metal pollutants from aqueous solution.

Fe, N, S co-doped cellulose paper carbon fibers as an air-cathode catalyst for microbial fuel cells

The heteroatoms and transition metal co-doped carbon-based catalysts are an important way to improve the catalytic activity of oxygen reduction reaction (ORR). Herein, we reported a facile method to obtain iron, nitrogen, and sulfur co-doped cellulose paper carbon fibers as catalysts (Fe-N-S/CFs) for ORR in microbial fuel cells (MFCs) with the adsorption recovery of Congo red molecules from dye wastewater. The thermal treatment promoted the etching of carbon surface by ferric ions, resulting in increased surface roughness for forming the defective carbon structure. The rich active species and defective carbon formed on the etched surface to enhance the electroactive surface area and effective sites. Fe-N-S/CFs catalysts achieved high half-wave potential due to the synergy effect between chemical components and defect structures. The assembled single-chamber air cathode MFC gained a high maximum power density of 1773 ± 40 mW m^-2 versus Pt/C MFC of 1325 ± 94 mW m^-2. This work provides a strategy for recovering dye molecules from wastewater to prepare non-precious metal catalysts for enhancing ORR activity.

Alginate@Fe3O4@Bentonite nanocomposite for formaldehyde removal from synthetic and real effluent: optimization by central composite design

In this study, Alginate@ Fe₃O₄/Bentonite nanocomposite was utilized to eliminate formaldehyde from wastewater. Structural features of bentonite, bentonite@Fe₃O₄, and Alginate@Fe₃O₄@Bentonite were determined using FT-IR, PXRD, Mapping, EDX, TEM, SEM, VSM, and BET analyses. The central composite design method was employed to find the optimal conditions for formaldehyde removal using Alg@Fe₃O₄@Bent nanocomposite. The maximum formaldehyde uptake efficiency (94.56%) was obtained at formaldehyde concentration of 10.69 ppm, the nanocomposite dose of 1.28 g/L, and pH of 9.96 after 16.53 min. Also, Alginate@Fe₃O₄@Bentonite composite was used to eliminate formaldehyde from Razi petrochemical wastewater and was able to eliminate 91.24% of formaldehyde, 70% of COD, and 68.9% of BOD₅. The isotherm and kinetic investigations demonstrated that the formaldehyde uptake process by the foresaid adsorbent follows the Langmuir isotherm and quasi-first-order kinetic models, respectively. Also, the maximum uptake capacity was obtained at 50.25 mg/g. Moreover, the formaldehyde uptake process by the aforementioned nanocomposite was exothermic and spontaneous. Furthermore, the formaldehyde adsorption efficiency decreased slightly after six reuse cycles (less than 10%), indicating that Alginate@Fe₃O₄@Bentonite nanocomposite has remarkable recyclability. Besides, the influence of interfering ions like nitrate, carbonate, chloride, phosphate, and sulfate was studied on the formaldehyde removal efficiency and the results displayed that all ions except nitrate ion have low interaction with formaldehyde (less than 3% reduction in removal efficiency).

Adsorption of heavy metal onto biomass-derived activated carbon: review

Due to the rapid development of the social economy and the massive increase in population, human beings continue to undertake processing, and commercial manufacturing activities of heavy metals, which has caused serious damage to the environment and human health. Heavy metals lead to serious environmental problems such as soil contamination and water pollution. Human health and the living environment are closely affected by the handling of heavy metals. Researchers must find several simple, economical and practical methods to adsorb heavy metals. Adsorption technology has been recognized as an efficient and economic strategy, exhibiting the advantages of recovering and reusing adsorbents. Biomass-derived activated carbon adsorbents offer large adjustable specific surface area, hierarchically porous structure, strong adsorption capacity, and excellent high economic applicability. This paper focuses on reviewing the preparation methods of biomass-derived activated carbon in the past five years. The application of representative biomass-derived activated carbon in the adsorption of heavy metals preferentially was described to optimize the critical parameters of the activation type of samples and process conditions. The key factors of the adsorbent, the physicochemical properties of the heavy metals, and the adsorption conditions affecting the adsorption of heavy metals are highlighted. In addition, the challenges faced by biomass-derived activated carbon are also discussed.

Preparation of environment-friendly SiO2 aerogel based on waste boron mud and its adsorption behavior for toluene

To mitigate the environmental hazards of boron mud waste accumulation, we prepared environmental-friendly SiO₂ aerogels by extracting them through alkaline leaching treatment and optimized the experimental conditions. The optimum process parameters for alkaline leaching solution NaOH concentration, leaching temperature, solid-to-liquid ratio, and leaching time were 2 mol/L, 95 °C, 1:4, and 3 h, respectively. In this work, cheap and non-toxic hydroxy silicone oil (PDMS-OH) and hydrogen-containing silicone oil (PMHS) were used as surface modifiers instead of toxic and expensive trimethylchlorosilane (TMCS) in the SiO₂ aerogel modification process. The best performance under the optimum conditions was achieved with 60% PDMS-OH-modified SiO₂ aerogel. Organic liquid spills, represented by toluene, pose a great danger to the environment and water bodies. We treated free toluene on the water surface with the aerogel mentioned above and its adsorption capacity was up to 2,655 mg/g. After the adsorption of toluene, the aerogels coalesced into agglomerates for subsequent collection and handling. Furthermore, after five repeated applications, the adsorption capacity remained at 91.43% of the initial application. Overall, this research provided an inexpensive and simple solution for the treatment of organic liquids in wastewater.

Biosorption of heavy metals by microorganisms: Evaluation of different underlying mechanisms

Globally, ecotoxicologists, environmental biologists, biochemists, pathologists, and other experts are concerned about environmental contamination. Numerous pollutants, such as harmful heavy metals and emerging hazardous chemicals, are pervasive sources of water pollution. Water pollution and sustainable development have several eradication strategies proposed and used. Biosorption is a low-cost, easy-to-use, profitable, and efficient method of removing pollutants from water resources. Microorganisms are effective biosorbents, and their biosorption efficacy varies based on several aspects, such as ambient factors, sorbing materials, and metals to be removed. Microbial culture survival is also important. Biofilm agglomerates play an important function in metal uptake by extracellular polymeric molecules from water resources. This study investigates the occurrence of heavy metals, their removal by biosorption techniques, and the influence of variables such as those indicated above on biosorption performance. Ion exchange, complexation, precipitation, and physical adsorption are all components of biosorption. Between 20 and 35 °C is the optimal temperature range for biosorption efficiency from water resources. Utilizing living microorganisms that interact with the active functional groups found in the water contaminants might increase biosorption efficiency. This article discusses the negative impacts of microorganisms on living things and provides an outline of how they affect the elimination of heavy metals.

Membrane Separation Used as Treatment of Alkaline Wastewater from a Maritime Scrubber Unit

Since 1 January 2020, the sulfur content allowed in exhaust gas plume generated by marine vessels decreased to 0.5% m/m. To be compliant, a hybrid scrubber was installed on-board, working in closed loop and generating a high volume of alkaline wastewater. The alkaline water suspension was treated by a silicon carbide multitubular membrane to remove pollutants, and to allow the water discharge into the natural environment. In this paper, membrane filtration behavior was analyzed for the maritime scrubber wastewater. A range of operating parameters were obtained for several feedwater quality-respecting industrial constraints. The objective was an improvement of (I) the water recovery rate, (II) the filtration duration, and (III) the permeate quality. Thus, in high-fouling water, a low permeate flow (60 L h^-1 m^-2) with frequent backflushing (every 20 min) was used to maintain membrane performance over time. In terms of water quality, the suspended solids and heavy metals were retained at more than 99% and 90%, respectively. Other seawater discharge criteria in terms of suspended solids concentration, pH, and polyaromatic hydrocarbons were validated. The recommended operating conditions from laboratory study at semi-industrial scale were then implemented on a vessel in real navigation conditions with results in agreement with expectations.

A comprehensive review on the coagulant recovery and reuse from drinking water treatment sludge

The main treatment unit in conventional systems for surface water is coagulation-flocculation (CF) process, which consumes huge quantities of coagulant, and produces large volume of sludge. The produced sludge is known as one of the components of water treatment sludge (WTS), which is considered as a global issue and hot topic require careful attention from the plant operators and sludge managers to be managed sustainably with applying an ecofriendly method. Among the suggested technologies, recovery and reuse of coagulants from WTS show the potential to decrease the waste disposal and chemicals usage for drinking water treatment significantly. So, this comprehensive review provides a useful insight into environmental and health problems of WTS, reports the sources, physicochemical properties of sludge, describes different sludge management methods by more focus on coagulant recovery (CR), which significantly point out the different aspects of WTS recovery and reuse, and eventually, economic evaluation of the CR process was also discussed. The results of this review confirm that coagulants can be recovered from WTS by different methods and also will be reused for multiple times in the removal of pollutants from water and wastewater. Moreover, the recovered coagulants can be used as building and construction materials, constructed wetlands substrate and other aims.

Green, Sustainable Synthesis of γ-Fe2O3/MWCNT/Ag Nano-Composites Using the Viscum album Leaf Extract and Waste Car Tire for Removal of Sulfamethazine and Bacteria from Wastewater Streams

Multi-walled carbon nanotubes (MWCNTs) decorated with Ag nanoparticles (NPs) are bifunctional adsorbent nanomaterials with antibacterial activity. They can be magnetically recovered from wastewater in case of coupling with γ-Fe₂O₃. In this study, for the first time, an environmentally friendly technique was applied to prepare a nanocomposite (NC) material composed of γ-Fe₂O₃/MWCNT/Ag by using Bridgestone disposable tires and Viscum album leaves extract. γ-Fe₂O₃/MWCNTs/Ag NC was employed for the removal of sulfamethazine (SMT) from aqueous solutions. Under the optimized conditions determined via the Taguchi method, the highest SMT adsorption capacity of the γ-Fe₂O₃/MWCNT/Ag NC was measured to be 47.6 mg/g. The experimental data fitted well with the pseudo-second-order kinetic model and the Langmuir isotherm. The thermodynamic parameters implied that the adsorption process was endothermic. In addition to adsorption of the drug pollutant, the NC demonstrated a superior antibacterial activity against Gram-positive bacteria. The reusability test also showed that over 79% SMT can be removed using γ-Fe₂O₃/MWCNTs/Ag NC even after four adsorption cycles. Taken together, γ-Fe₂O₃/MWCNTs/Ag NC was proven to be a promising antibacterial nano-adsorbent for wastewater treatment.

Porphyrin-Based Conjugated Microporous Polymers for Highly Efficient Adsorption of Metal Ions

The capture and elimination of anions and cations from water have attracted a great deal of attention and are quite vital for clean production and environmental remediation. In this work, we present the synthesis of four porphyrin (Por)-based conjugated microporous polymers (CMPs, namely, Por-CMP-1-4), which were produced through a Sonogashira-Hagihara linked response using porphyrin and acetylene aromatic compounds as building blocks and used as absorbents to eliminate metal ions from water. The as-synthesized Por-CMP-1-4 exhibit an amorphous porous structure and outstanding caloric and physicochemical properties. Taking advantage of their larger specific surface areas, i.e., 541.47, 614.58, 382.38, and 677.90 m² g^-1 for Por-CMP-1-4, respectively, and their chelating active site that originated from the porphyrin ring, Por-CMP-1-4 show better Zn²⁺, Cu²⁺, and Pb²⁺ adsorption ability. Among them, Por-CMP-3 has the greatest adsorbability of 640 mg g^-1 for Zn²⁺, with an adsorption efficiency of 80%, whereas its adsorption capacities for Cu²⁺ and Pb²⁺ ions were both 334 mg g^-1, with an adsorption efficiency of 42% for Cu²⁺ and Pb²⁺. Employing Por-CMP-3 as a representative example, its adsorption kinetics has been systematically investigated. The adsorption behavior of Por-CMP-3 with respect to the Zn²⁺ ion is shown to exhibit pseudo-first-order kinetics and Langmuir isotherm modes. Meanwhile, the adsorption mechanism is discussed in detail, and it was thought it might be chelation, in which the nitrogen atoms with a single pair of electrons on the porphyrin ring interacted with metal ions to form stable chelation coordination bonds, thus removing metal ions selectively and effectively. Furthermore, Por-CMP-3 exhibited good reusability, retaining 60% of its Zn²⁺ removal rate after four continuous adsorptions.

Development of lab-on-chip biosensor for the detection of toxic heavy metals: A review

Recently, a decrease in water availability and quality has been raised due to rapid industrialization, unsustainable agricultural activities and anthropogenic activities. Heavy metals are considered significant pollutants in the water environment, cause environmental hazards and health effects to humans. For monitoring water contaminants utilized different conventional techniques. Still, they have some drawbacks, such as cost expensive, ecological issues, and processing time, requiring technicians and researchers to operate them effectively. Biosensors have become reasonable devices for screening and identifying environmental contaminants because of their different benefits contrasted with other detecting techniques. This review summarizes the toxic effect of heavy metal and their source, occurrence. A detailed discussion is provided on the heavy metal recognition materials for detecting heavy metals in wastewater. Lab on chip (LOC) is an emerging micro-electrical mechanical system (MEMS) device that intakes liquid and makes it move through the micro-channels, to accomplish fast, cost-effective and profoundly sensitive analysis with significant yield. LOC also provided a discussion on numerous laboratory functions on a single platform. This article attempts to discuss the detection of heavy metals using lab on a chip by suitable recognition materials. Further, the design and fabrication mechanism and their recognition abilities of LOC were also reviewed. The review mainly focuses on the application of LOC biosensors, pros, and cons, and suggests a roadmap towards future development to enhance the practical use in pollutant monitoring.

Waste tea residue adsorption coupled with electrocoagulation for improvement of copper and nickel ions removal from simulated wastewater

The present research involves removing copper and nickel ions from synthesized wastewater by using a simple, cheap, cost-effective, and sustainable activated green waste tea residue (AGWTR) adsorption coupled with electrocoagulation (ADS/EC) process in the presence of iron electrodes. By considering previous studies, their adsorbents used for treating their wastewaters firstly activate them by applying either chemicals or activating agents. However, our adsorbent was prepared without applying neither chemicals nor any activating agents. The operating parameters such as pH, hydraulic retention time, adsorbent dose, initial concentration, current density, and operating cost for both metals were optimized. In ADS/EC, the removal efficiency was obtained as 100% for copper and 99.99% for nickel ions. After the ADS/EC process, Fourier transform infrared (FT-IR) spectroscopy, Scanning Electron Microscopy (SEM) and Energy-dispersive X-ray spectroscopy (EDS) analysis were used to characterize the adsorbent green waste tea residue. The adsorption isotherm and kinetic model results showed that the Langmuir and the pseudo-second-order were well-fitted to the experimental adsorption data better than the Freundlich and pseudo-first-order models for both Cu²⁺ and Ni²⁺ with their maximum adsorption capacity of 15.6 and 15.9 mg g⁻¹, respectively. The above results give an option to recycle the metal-based industrial effluents, tea industry-based wastes, enabling a waste-to-green technique for adsorbing and removing the heavy metals and other pollutants in water.

Chitosan@Carboxymethylcellulose/CuO-Co2O3 Nanoadsorbent as a Super Catalyst for the Removal of Water Pollutants

In this work, an efficient nanocatalyst was developed based on nanoadsorbent beads. Herein, carboxymethyl cellulose–copper oxide-cobalt oxide nanocomposite beads (CMC/CuO-Co2O3) crosslinked by using AlCl3 were successfully prepared. The beads were then coated with chitosan (Cs), Cs@CMC/CuO-Co2O3. The prepared beads, CMC/CuO-Co2O3 and Cs@CMC/CuO-Co2O3, were utilized as adsorbents for heavy metal ions (Ni, Fe, Ag and Zn). By using CMC/CuO-Co2O3 and Cs@CMC/CuO-Co2O3, the distribution coefficients (Kd) for Ni, Fe, Ag and Zn were (41.166 and 6173.6 mLg−1), (136.3 and 1500 mLg−1), (20,739.1 and 1941.1 mLg−1) and (86.9 and 2333.3 mLg−1), respectively. Thus, Ni was highly adsorbed by Cs@CMC/CuO-Co2O3 beads. The metal ion adsorbed on the beads were converted into nanoparticles by treating with reducing agent (NaBH4) and named Ni/Cs@CMC/CuO-Co2O3. Further, the prepared nanoparticles-decorated beads (Ni/Cs@CMC/CuO-Co2O3) were utilized as nanocatalysts for the reduction of organic and inorganic pollutants (4-nitophenol, MO, EY dyes and potassium ferricyanide K3[Fe(CN)6]) in the presence of NaBH4. Among all catalysts, Ni/Cs@CMC/CuO-Co2O3 had the highest catalytic activity toward MO, EY and K3[Fe(CN)6], removing up to 98% in 2.0 min, 90 % in 6.0 min and 91% in 6.0 min, respectively. The reduction rate constants of MO, EY, 4-NP and K3[Fe(CN)6] were 1.06 × 10−1, 4.58 × 10−3, 4.26 × 10−3 and 5.1 × 10−3 s−1, respectively. Additionally, the catalytic activity of the Ni/Cs@CMC/CuO-Co2O3 beads was effectively optimized. The stability and recyclability of the beads were tested up to five times for the catalytic reduction of MO, EY and K3[Fe(CN)6]. It was confirmed that the designed nanocomposite beads are ecofriendly and efficient with high strength and stability as catalysts for the reduction of organic and inorganic pollutants.

A review on adsorptive separation of toxic metals from aquatic system using biochar produced from agro-waste

Water is a basic and significant asset for living beings. Water assets are progressively diminishing due to huge populace development, industrial activities, urbanization and rural exercises. Few heavy metals include zinc, copper, lead, nickel, cadmium and so forth can easily transfer into the water system either direct or indirect activities of electroplating, mining, tannery, painting, fertilizer industries and so forth. The different treatment techniques have been utilized to eliminate the heavy metals from aquatic system, which includes coagulation/flocculation, precipitation, membrane filtration, oxidation, flotation, ion exchange, photo catalysis and adsorption. The adsorption technique is a better option than other techniques because it can eliminate heavy metals even at lower metal ions concentration, simplicity and better regeneration behavior. Agricultural wastes are low-cost biosorbent and typically containing cellulose have the ability to absorb a variety of contaminants. It is important to note that almost all agro wastes are no longer used in their original form but are instead processed in a variety of techniques to improve the adsorption capacity of the substance. The wide range of adsorption capacities for agro waste materials were observed and almost more than 99% removal of toxic pollutants from aquatic systems were achieved using modified agro-waste materials. The present review aims at the water pollution due to heavy metals, as well as various heavy metal removal treatment procedures. The primary objectives of this research is to include an overview of adsorption and various agriculture based adsorbents and its comparison in heavy metal removal.

Study on the aerobic remediation of Ni(II) by Pseudomonas hibiscicola strain L1 interaction with nitrate

Aerobic denitrifying bacteria have the potential to remove the co-pollutants Ni(II) and nitrate in industrial wastewater. In this study, aerobic denitrifying bacteria with significant Ni(II) removal efficiency was isolated from the biological reaction tank and named as Pseudomonas hibiscicola L1 strain after 16 S rRNA identification analysis. The removal of ever-increasing Ni(II) and NO₃^--N wastewater under aerobic conditions by strain L1 was discussed. The experimental results showed that strain L1 removed 84% of Ni(II) and 81% of COD, with the use of 34.8 mg L^-1 of nitrogen source and without nitrite accumulation yet. Strain L1 had remarkable activity (OD₆₀₀ = 0.51-0.56 (p < 0.05)) at 20 mg L^-1 of Ni(II) and 100 mg L^-1 of NO₃^--N. It was found that high Ni(II) gradients (2-10 mg L^-1) had little effect on nitrate removal ratio (35-34% (p > 0.05), and the removal ratios of Ni(II) was enhanced (from 42% to 83% (p < 0.05)) by increasing nitrate (25-100 mg L^-1). Also, the results indicated that strain L1 could reduce Ni(II) and nitrate under different pH (6-9); electron donor-glucose, sodium acetate, sodium succinate and trisodium citrate; C/N (5-20) and coexisting ions (Cu(II) and Zn(II)). Notably, the nitrogen balance analysis showed 32.4% of TN was lost nitrogen and 19.7% of TN was assimilated for cell growth, which indicated aerobic denitrification process of strain L1. Meanwhile, characterization technology (SEM, FTIR, and XRD) showed Ni(II) was bioadsorbed in the form of Ni(NH₂)₂, NiCO₃, and Ni(OH)₂·2H₂O through surface functional groups. This research provides new microbial method for the simultaneous removal of nitrate and Ni(II) in wastewater.

Surface improved agro-based material for the effective separation of toxic Ni(II) ions from aquatic environment

In this present study, a novel and low cost surface improved material was prepared from the farm waste material (Borassus flabellifer male inflorescence) and its surface was enhanced by the sulphuric acid treatment to intensify the Ni(II) ions adsorption. The adsorption individualities such as availability of functional groups, essential elements and the exterior side and structural properties of the material were assessed by the FT-IR, EDX, SEM and XRD investigation. The impact of varied adsorption influencing parameters on Ni(II) ions adsorption was studied and optimized as pH - 6.0, biosorbent dosage - 1.5 g/L, contact time - 60 min and temperature - 303 K via batch adsorption examination. Modeling examinations were carried with varied adsorption isotherm (Langmuir, Freundlich, Fritz-Schlunder and Temkin) and kinetic models (Pseudo-first order, Pseudo-second order and Elovich kinetics). Thermodynamic studies were carried out at varied Ni(II) ions concentrations (25 mg/L - 150 mg/L) and temperatures (303 K-333 K) to explain the nature of Ni(II) ions adsorption on Borassus flabellifer male inflorescence. The prepared material has shown the most suitable Ni(II) ions adsorption results for the Langmuir isotherm (R² = 0.9808) and Pseudo-first order kinetic models (R² = 0.9735 for 25 mg/L). Thereby, the modeling study revealed that the prepared material has received the Ni(II) ions adsorption capacity (q_m) value of 20.31 mg/g and the Ni(II) ions adsorption was physisorption. Thermodynamic results demonstrated that the Ni(II) ions adsorption was immediate, exothermic and favorable at low temperature.

Removal of heavy metal ion cobalt (II) from wastewater via adsorption method using microcrystalline cellulose-magnesium hydroxide

Microcrystalline cellulose (MCC), magnesium sulfate hexahydrate, and trisodium citrate were reacted in ammonia bath in an aqueous solution to prepare a MCC-magnesium hydroxide (MH) composite adsorbent, which was used to adsorb heavy metal Co(II) ion. The method of using MCC-MH to adsorb and remove Co(II) was studied under different pH values, adsorbent dosages, contact times, initial Co(II) ion concentrations, and temperatures. The optimal process parameters include an MCC-MH dosage of 2.5 mg/mL, a contact reaction equilibrium time of 50 min, a Co(II) solution pH of 6.0-8.0, an initial Co(II) concentration of 300 mg/L, and a temperature of 303 K. The removal rate of Co(II) solution by MCC-MH was as high as 97.67%, and the maximum adsorption capacity of MCC-MH reached 153.84 mg/g under these optimal conditions. The adsorption isotherm of Co(II) conformed to the Langmuir model, the kinetic data of Co(II) conformed to the pseudo-second-order kinetic model, and the adsorption of Co(II) by MCC-MH was a spontaneous endothermic reaction under the optimized conditions. Analytical studies showed that Co(II) adsorption on MCC-MH composites is affected by chemical adsorption and involves the influence of intraparticle diffusion to a certain extent.

Controllable synthesis of coral-like hierarchical porous magnesium hydroxide with various surface area and pore volume for lead and cadmium ion adsorption

A coral-like hierarchical porous magnesium hydroxide (HPMH) with various surface area and pore volume was controllably prepared using a simple one-step hydrothermal process, for which MgO, water and citric acid were applied. The citric acid (CA), as a structure-directing molecule, is a key factor in regulating the pore structure of HPMH products. With different additive dosages, the nanostructure, surface area and pore volume of HPMH products can be controllably regulated. The MH-CA20 product (prepared in the presence of 20 wt% CA) with high BET surface area (159 m²/g) and pore volume (0.75 cm³/g) was used to investigate the adsorption properties for Pb(II) and Cd(II) ions. The experimental adsorption capabilities of the MH-CA20 for Pb(II) and Cd(II) are respectively 4535 and 3530 mgg^-1, very close to the maximum adsorption capabilities calculated by Langmuir equation (4545 and 3571 mgg^-1). According to the adsorption kinetics and adsorption isotherm data, the adsorption process conforms to the Pseudo-second-order and Langmuir model, indicating that heavy metal ions conduct monolayer chemical adsorption mechanism. Since the preparation of HPMH is simple, low-cost and filtrate recycling, the process can easily be scaled up and could be a good candidate for application in tackling different wastewater.

Synthesis and application of a green surfactant for the treatment of water containing PFAS/ hazardous metal ions

In this work, the effectiveness of a biodegradable and natural surfactant synthesized through a novel method has been studied through the ion flotation process to treat waters containing Per/Poly Fluoroalkyl Substances (PFAS) and heavy-metal ions. This cysteine-based surfactant, which is environmentally acceptable, showed considerable solubility and foaming ability over a wide range of pH. It also could remove 97-99(%) of 5 mg/L of cadmium, chromium, copper, nickel, zinc, and manganese ions in a single batch physicochemical process. Moreover, for the first time, a foam fractionation method in association with using this cysteine-based surfactant was applied for perfluorooctanoic acid (PFOA) removal from water. This surfactant was used as a co-surfactant and could readily remove 72% of PFOA (40 mg/L) from water. The characterization of the surfactant was undertaken using ¹H NMR, FT-IR, elemental analysis, melting point, and determination of its critical micelle concentration (CMC). This environmentally friendly surfactant has high potential applications in green chemistry especially in the treatment of waters contaminated with PFAS/heavy-metal ions.

Waste to resource: preparation of an efficient adsorbent and its sustainable utilization in flame retardant polyurethane composites

In order to realize the comprehensive utilization of industrial solid waste and the treatment of water eutrophication, the flower-like magnesium hydroxide (MH) was synthesized from phosphorus tailings by sulfuric acid hydrolysis and a hydrothermal method and then was modified with a metal organic framework (MOF) to remove the phosphates enriched in water through adsorption. Both MH and MOF-modified MH (MH@MOF) presented good removal performance of phosphates. The phosphate-adsorbed composites (MH-P and MH@MOF-P) were sustainably used as effective flame retardants for thermoplastic polyurethane (TPU) at low loadings by a solution blending method. The cone calorimetry test results showed that MH@MOF-P can significantly reduce the heat release rate (HRR), smoke production rate (SPR), total smoke release (TSR), CO release rate and CO2 release rate of TPU composites, compared with those of neat TPU. The novel strategy proposed in this work is of great significance for resource recycling, environmental governance and improving fire safety of polymer materials.

Alkali-Activated Adsorbents from Slags: Column Adsorption and Regeneration Study for Nickel(II) Removal

Alkali-activated adsorbents were synthesized by mixing three different slags from the steel industry: blast furnace slag (BFS), ladle slag (LS), and Lintz–Donawitz converter slag (LD). These powdered slag-based geopolymers (GP) were used to remove nickel(II) from aqueous solutions in fixed-bed column studies. The experiments were conducted in pH 6 using a phosphate buffer with initial nickel(II) concentration of 50 mg/L. Samples were taken at time intervals of between 5 and 90 min. Three adsorption–desorption cycles were implemented with a flow rate of 5 mL/min. The geopolymers were characterized by Fourier-Transform Infrared Spectroscopy (FTIR), X-ray powder diffraction (XRD), Field Emission Scanning Electron Microscopy (FESEM), X-ray fluorescence (XRF), specific surface area measurements, and a leaching test. The data were found to describe the Thomas, Adams–Bohart, and Yoon–Nelson models well. For GP (BFS, LS), experimental adsorption capacity was 2.92 mg/g, and for GP (LD, BFS, LS), it was 1.34 mg/g. The results indicated that the produced adsorbents have the potential to be used as adsorbents for the removal of nickel(II).

Fir bark modified by Phanerodontia chrysosporium: A low-cost amendment for cd-contaminated water and agricultural soil

In this study, a modified fir barks (MFB) was prepared by mixing fir barks (FB) and white-rot fungi (Phanerodontia chrysosporium) under aerobic fermentation. The potential of MFB for Cd²⁺ adsorption was investigated by batch experiments combined with kinetic, isotherm, and thermodynamics analyses. The results revealed that the modification greatly increased the porous structures on the surfaces of fir barks and the surface area of MFB was much higher than that of FB. As a result, the adsorption capacity of Cd²⁺ on MFB (17.4 mg g^-1) was more than two times higher than that on FB (7.2 mg g^-1), and the adsorption of Cd²⁺ on MFB was controlled by physisorption and chemisorption. The immobilization of Cd by MFB in a contaminated agricultural soil was also investigated. The effect of MFB on the bioavailability of Cd was investigated using a leaching test (the European standard EN 12457-2) combined with a typical sequential extraction procedure (the community bureau of reference, BCR). The experimental results showed that the Cd leachability was reduced by 71% when the added MFB dosage was 30 mg g^-1. Besides, the MFB amendment could transform Cd from unstable geochemical fractions into more stable fractions. In total, the MFB, as a chemical-free and eco-friendly material, could be potentially employed for in-situ remediation of Cd-contaminated agricultural soils.

Adsorption of Cr(VI), Ni(II), Fe(II) and Cd(II) ions by KIAgNPs decorated MWCNTs in a batch and fixed bed process

The efficient removal of toxic metals ions from chemical industry wastewater is considered problematic due to the existence of pollutants as mixtures in the aqueous matrix, thus development of advanced and effective treatment method has been identified as a panacea to the lingering problems of heavy metal pollution. In this study, KIAgNPs decorated MWCNTs nano adsorbent was developed using combination of green chemistry protocol and chemical vapor deposition techniques and subsequently characterized using UV-Vis, HRTEM, HRSEM, XRD, FTIR and XPS. The adsorptive efficiency of MWCNTs-KIAgNPs for the removal of Cr(VI), Ni(II), Fe(II), Cd(II) and physico-chemical parameters like pH, TDS, COD, BOD, nitrates, sulphates, chlorides and phosphates from chemical industrial wastewater was examined in both batch and fixed bed systems. The result exhibited successful deposition of KIAgNPs on the surface of MWCNTs as confirmed by the microstructures, morphology, crystalline nature, functional groups and elemental characteristics of the MWCNTs-KIAgNPs. Optimum batch adsorption parameters include; pH (3 for Cr(VI) and 6 for Ni(II), Fe(II) and Cd(II) ions), contact time (60 min), adsorbent dosage (40 mg) and temperature (318 K). The binding capacities were obtained as follows; Cr⁶⁺ (229.540 mg/g), Ni²⁺ (174.784 mg/g), Fe²⁺ (149.552) and Cd²⁺ (121.026 mg/g), respectively. Langmuir isotherm and pseudo-second order kinetic model best described the experimental data in batch adsorption, while the thermodynamic parameters validated the chemisorption and endothermic nature of the adsorption process. In continuous adsorption, the metal ions were effectively removed at low metal influent concentration, low flow rate and high bed depth, whereby the experimental data were designated by Thomas model. The high physico-chemical parameters in the wastewater were successfully treated in both batch and fixed bed systems to fall within WHO permissible concentrations. The adsorption/desorption study illustrated over 80% metal removal by MWCNTs-KIAgNPs even after 8th adsorption cycle. This study demonstrated excellent performance of MWCNTs-KIAgNPs for chemical industry wastewater treatment.

Cadmium and copper heavy metal treatment from water resources by high-performance folic acid-graphene oxide nanocomposite adsorbent and evaluation of adsorptive mechanism using computational intelligence, isotherm, kinetic, and thermodynamic analyses

In this paper, folic acid-coated graphene oxide nanocomposite (FA-GO) is used as an adsorbent for the treatment of heavy metals including cadmium (Cd²⁺) and copper (Cu²⁺) ions. As such, graphene oxide (GO) is modified by folic acid (FA) to synthesize FA-GO nanocomposite and characterized by the atomic force microscopy (AFM), Fourier transform-infrared (FT-IR) spectrophotometry, scanning electron microscopy (SEM), and C/H/N elemental analyses. Also, computational intelligence tests are used to study the mechanism of the interaction of FA molecules with GO. Based on the results, FA molecules formed a strong π-π stacking, chemical, and hydrogen bond interactions with functional groups of GO. Main parameters including pH of the sample solution, amounts of adsorbent, and contact time are studied and optimized by the Response Surface Methodology Based on Central Composite Design (RSM-CCD). In this study, the equilibrium of adsorption is appraised by two (Langmuir and Freundlich and Temkin and D-R models) and three parameter (Sips, Toth, and Khan models) isotherms. Based on the two parameter evaluations, Langmuir and Freundlich models have high accuracy according to the R² coefficient (more than 0.9) in experimental curve fittings of each pollutant adsorption. But, multilayer adsorption of each contaminant onto the FA-GO adsorbent (Freundlich equation) is demonstrated by three parameter isotherm analysis. Also, isotherm calculations express maximum computational adsorption capacities of 103.1 and 116.3 mg g^-1 for Cd²⁺ and Cu²⁺ ions, correspondingly. Kinetic models are scrutinized and the outcomes depict the adsorption of both Cd²⁺ and Cu²⁺ followed by the pseudo-second-order equation. Meanwhile, the results of the geometric model illustrate that the variation of adsorption and desorption rates do not have any interfering during the adsorption process. Finally, thermodynamic studies show that the adsorption of Cu²⁺ and Cd²⁺ onto the FA-GO nanocomposite is an endothermic and spontaneous process.