Spatially high-resolved monitoring and risk assessment of polycyclic aromatic hydrocarbons in an industrial city

Polybrominated diphenyl ethers in indoor dust from Brazil: assessing demographic differences and human health exposure

Indoor house dust is considered an important human exposure route to polybrominated diphenyl ethers (PBDEs), which has raised concern about their environmental persistence and toxicity properties. In this study, eight PBDEs (BDE-28, -47, -99, -100, -153, -154, -183, and -209) were determined in house dust from two cities with different socio-demographic characteristics from Brazil, examining possible relationships with factors that potentially influence contamination (population density, economic activities, presence of electronic equipment, and so on) and also estimating the risk of human exposure through oral ingestion and dermal contact. The Σ8PBDE concentration in Sorocaba city ranged between 380 and 4269 ng/g dw, while in Itapetininga city ranged from 106 to 1000 ng/g dw. In both regions, BDE-209 was the most abundantly found congener, followed by BDE-99. House dust from Sorocaba presented significantly greater concentrations of BDE-183 and BDE-209 than Itapetininga. Regarding risk exposure assessment, the estimated daily intake (EDI) of PBDEs was much lower than their respective reference doses (RfDs) in all pathways estimated (non-dietary ingestion and dermal contact). This study provided valuable data to improve the knowledge about the presence and exposure to PBDEs in Brazilian house dust in comparison to other developing countries and the need to control environmental pollution and protect human health.

Atmospheric occurrences and bioavailability health risk of PAHs and their derivatives surrounding a non-ferrous metal smelting plant

Non-ferrous metal smelting emits large amounts of organic compounds into the atmosphere. Herein, 20 parent polycyclic aromatic hydrocarbons (PPAHs), 9 nitrated PAHs (NPAHs), 14 chlorinated PAHs (ClPAHs), and 6 alkylated PAHs (APAHs) in atmospheric samples from a typical non-ferrous metal smelting plant (NMSP) and residential areas were detected. In NMSP, benzo[a]pyrene, dibenz[a,h]anthracene, 6-nitrochrysene, 9-chlorofluorene, and 1-methylfluorene were the predominant compounds in the particulate phase, while phenanthrene constituted 57.3% in the gaseous phase. The concentration of PAHs in residential areas around NMSP was 1.8 times higher than that in the control area. Additionally, there was a significant negative correlation between the concentration and the distance from the NMSP. In terms of health risks, although the skin penetration coefficient of PM2.5 is smaller than that of the gaseous phase, dermal absorption of PM2.5 posed a greater threat to the population, the incremental lifetime cancer risk (ILCR) of NMSP was 1.8 × 10-4. After considering bioavailability, BILCR decreased by 1-2 orders of magnitude in different regions, and dermal absorption decreased more than inhalation intake. Nevertheless, the dermal absorption of PM2.5 in NMSP still presents a probable carcinogenic risk. This study provides a necessary reference for the subsequent control of NMSP contamination.

Geographic information system-based determination of priority monitoring areas for hazardous air pollutants in an industrial city

Industrial cities are hotspots for many hazardous air pollutants (HAPs), which are detrimental to human health. We devised an identification method to determine priority HAP monitoring areas using a comprehensive approach involving monitoring, modeling, and demographics. The methodology to identify the priority HAP monitoring area consists of two parts: (1) mapping the spatial distribution of selected categories relevant to the target pollutant and (2) integrating the distribution maps of various categories and subsequent scoring. The identification method was applied in Ulsan, the largest industrial city in South Korea, to identify priority HAP monitoring areas. Four categories related to HAPs were used in the method: (1) concentrations of HAPs, (2) amount of HAP emissions, (3) the contribution of industrial activities, and (4) population density in the city. This method can be used to select priority HAP monitoring areas for intensive monitoring campaigns, cohort studies, and epidemiological studies.

Mapping the spatial distribution of primary and secondary PM2.5 in a multi-industrial city by combining monitoring and modeling results

Industrial cities are strongly influenced by primary emissions of PM2.5 from local industries. In addition, gaseous precursors, such as sulfur oxides (SOX), nitrogen oxides (NOX), and volatile organic compounds (VOCs), emitted from industrial sources, undergo conversion into secondary inorganic and organic aerosols (SIAs and SOAs). In this study, the spatial distributions of primary and secondary PM2.5 in Ulsan, the largest industrial city in South Korea, were visualized. PM2.5 components (ions, carbons, and metals) and PM2.5 precursors (SO2, NO2, NH3, and VOCs) were measured to estimate the concentrations of secondary inorganic ions (SO42-, NO3-, and NH4+) and secondary organic aerosol formation potential (SOAFP). The spatial distributions of SIAs and SOAs were then plotted by combining atmospheric dispersion modeling, receptor modeling, and monitoring data. Spatial distribution maps of primary and secondary PM2.5 provide fundamental insights for formulating management policies in different districts of Ulsan. For instance, among the five districts in Ulsan, Nam-gu exhibited the highest levels of primary PM2.5 and secondary nitrate. Consequently, controlling both PM2.5 and NO2 emissions becomes essential in this district. The methodology developed in this study successfully identified areas with dominant contributions from both primary emissions and secondary formation. This approach can be further applied to prioritize control measures during periods of elevated PM levels in other industrial cities.

The passive sampler assisted human exposure risk characterization for tetrachloroethene soil vapor intrusion scenario

The potential human health risks associated with soil vapor intrusion and volatile organic compounds (VOCs) exposure were characterized at an industrialized site by the quantification of gaseous VOCs in soil pores using a passive sampling technique. The gaseous tetrachloroethene (PCE) in soil pores varied between 12 and 5,400 μg m-3 showing 3 orders of magnitude variation with dependence on groundwater PCE concentrations. Though the PCE concentration in the air only varied between 0.45 and 1.5 μg m-3 showing negligible variations compared to the variation observed in soil pores. The PCE concentration in the air varied between 0.45 and 1.5 μg m-3. The calculation of fugacity suggested that the PCE in the test site originated from groundwater. Measured PCE in groundwater ranged from 14 to 2,400 times higher than PCE in soil gas. This indicates that conducting a vapor intrusion risk assessment using passive soil gas sampling is critical for accurate risk characterization and assessment. Estimated PCE inhalation cancer risks for street cleaners and indoor residents varied between 10-6 and 10-4 with a low plausible hazard, and between 10-3 and 10-2 with a high risk, respectively. The results of this study demonstrate that passive sampling offers a significantly lower cost and labor-intensive approach compared to traditional methods for assessing pollution distribution in contaminated sites and characterizing risks. This highlights the potential for wider application of passive sampling techniques in environmental studies.

Investigating industrial PAH air pollution in relation to population exposure in major countries: A scoring approach

Polycyclic aromatic hydrocarbons (PAHs) are common air pollutants worldwide, associated with industrial processes. In the general population, both modeling and field studies revealed a positive correlation between air PAH concentrations and urinary PAH metabolite levels. Many countries lack population urinary data that correspond to local PAH air concentrations. Thus, we proposed a scoring-based approximate approach to investigating that correlation in selected countries, hypothesizing that PAH air concentrations in selected regions could represent the national air quality influenced by industrial emission and further correlate to PAH internal exposure in the general population. This research compiled 85 peer-reviewed journal articles and 9 official monitoring datasets/reports covering 34 countries, 16 of which with both atmospheric PAH data and human biomonitoring data. For the air pollution score (AirS), Egypt had the highest AirS at 0.94 and Pakistan was at the bottom of the score ranking at -1.95, as well as the median in the UK (AirS: 0.50). For the population exposure score (ExpS), China gained the top ExpS at 0.44 and Spain was with the lowest ExpS of -1.52, with the median value in Italy (ExpS: 0.43). Through the correlation analysis, atmospheric PAHs and their corresponding urinary metabolites provided a positive relationship to a diverse extent, indicating that the related urinary metabolites could reflect the population's exposure to specific atmospheric PAHs. The findings also revealed that in the 16 selected countries, AirS indexes were positively correlated with ExpS indexes, implying that higher PAH levels in the air may lead to elevated metabolite urinary levels in general populations. Furthermore, lowering PAH air concentrations could reduce population internal PAH exposure, implying that strict PAH air regulation or emission would reduce health risks for general populations. Notably, this study was an ideal theoretical research based on proposed assumptions to some extent. Further research should focus on understanding exposure pathways, protecting vulnerable populations, and improving the PAH database to optimize PAH pollution control.

PM-bound polycyclic aromatic compounds (PACs) in two large-scale petrochemical bases in South China: Spatial variations, sources, and risk assessment

Polycyclic aromatic compounds (PACs) are potential pollutants emitted from the petrochemical industry, whereas their occurrence and sources in petrochemical regions are still poorly known. The present study revealed the spatial variations, compositional profiles, sources and contributions, and health risks of PM-bound PACs in two large-scale petrochemical bases (GDPB and HNPB) in South China. The concentrations of parent polycyclic aromatic hydrocarbons (PAHs) were 7.14 ± 3.16 ng/m³ for ∑₁₈PAHs and 0.608 ± 0.294 ng/m³ for the PAHs with molecular weight of 302 amu (MW302 PAHs) in the GDPB base and 2.55 ± 1.26 ng/m³ and 0.189 ± 0.088 ng/m³ in the HNPB base. Oxygenated PAHs (OPAHs) showed comparable concentrations to the parent PAHs in both the bases and nitrated PAHs (NPAHs) had the lowest mean levels (260 pg/m³ and 59.4 pg/m³ in the two regions). Coronene, 2,8-dinitrodibenzothiophene, and dibenzo[a,e]fluoranthene showed remarkably higher contributions to the PAC and can be PAC markers of the petrochemical industry source. Five sources of PACs were identified respectively in both petrochemical bases by the positive matrix factorization (PMF) model. The vehicle (and ship) traffic exhaust was the primary source of PACs (contributed 33% to the ∑PACs), and the sources related to the coking of coal and heavy petroleum and refinery exhaust were identified in both bases, with contributions of 10-20%. PACs in GDPB also contributed from secondary atmospheric reactions (17.3%) and the usage of sulfur-containing fuels (20.9%), while the aromatics industry made a significant contribution (20.1%) to the PACs in the HNPB region. The cumulative incremental lifetime cancer risks (ILCRs) induced by inhalation of PM-bound PACs in both petrochemical bases were low (10^-8-10^-6). For the sources related to the petrochemical industry, coking activities and the aromatic industry were the significant contributors to the ∑ILCRs in GDPB and HNPB, respectively. This research has implications for further source-targeted control and health risk reduction of PACs in petrochemical regions.

Profiling and occupational health risk assessment study on coal ashes in terms of polycyclic aromatic hydrocarbons (PAHs)

Profiling and cancer risk assessment on the polycyclic aromatic hydrocarbons (PAHs) content of coal ashes produced by the major coal combustion plants from the eastern coalfield region in India was conducted. Thirteen PAHs were detected on coal ashes collected from ash deposition sites of major thermal power plants and the profiling of the PAHs was done. Benzo[a]pyrene equivalents (BaP_eq) for individual PAHs were calculated and applied to the probabilistic assessment model from US EPA (1989). Monte Carlo simulations were conducted to assess the risk of inhabitants exposed to PAHs through the dust of the coal ash deposition site. In fly ash, the range of total amount of carcinogenic PAHs was from 3.50 to 6.72 µg g^-1 and for the bottom ash, the range was 8.49 to 14.91 µg g^-1. Bottom ashes were loaded with ample amounts of 5- and 6-ring carcinogenic PAHs, whereas fly ashes were dominated by medium molecular weight PAHs. The simulated mean cancer risks from fly ashes were 2.187 E-06 for children and 3.749 E-06 for adults. For the case of bottom ash, the mean risks were 1.248 E-05 and 2.173 E-05 respectively for children and adults. Among all the three exposure routes, dermal contact was the major and caused 81% of the total cancer risk. The most sensitive parameters were exposure duration and relative skin adherence factor for soil, which contributed the most to total variation. The 90% risks calculated from the bottom ashes (2.617 E-05 for children and 4.803 E-05 for adults) are marginally above the acceptable limit (>1.000 E-06) according to US EPA. In this study, a comprehensive risk assessment on carcinogenic PAHs present in coal ashes was done for the first time that may be helpful to develop potential strategies against occupational cancer risk.

Occurrence of persistent organic pollutants (POPs) in the atmosphere of South Korea: A review

Numerous studies found the presence of persistent organic pollutants (POPs) in various environmental compartments, including air, water, and soil. POPs have been discovered in various industrial and agricultural products with severe environmental and human health consequences. According to the data, South Korea is a hotspot for POP pollution in the southern part of Asia; hence, South Korea has implemented the Stockholm Convention's National Implementation Plan (NIP) to address this worldwide issue. The purpose of this review is to assess the distribution pattern of POPs pollution in South Korea's atmosphere. According to findings, PAHs, PCBs, BFRs, and PBDEs significantly polluted the atmosphere of South Korea; however, assessing their exposure nationwide is difficult due to a shortage of data. The POPs temporal trend and meta-analysis disclosed no proof of a decrease in PAHs and BFRs residues in the atmosphere. However, POP pollution in South Korea tends to decrease compared to contamination levels in neighboring countries like Japan and China.

Assessment of currently used organochlorine pesticides in surface water and sediments in Xiangjiang river, a drinking water source in China: Occurrence and distribution characteristics under flood events

Xiangjiang (XJ) is a typical urban inland river that serves as a drinking water source, which may be affected by the currently used organochlorine pesticides (CUOCPs) originating from agricultural activities in the vicinity. On this basis, this study comprehensively explored the occurrence and distribution characteristics of CUOCPs in surface water and sediments under long-term precipitation and subsequent floods. Considering the low concentration of CUOCPs in water, a technique combining high-throughput organic analysis with high-volume solid phase extraction (High-throat/Hi-volume SPE) was introduced for effective analysis of CUCOPs. The results showed that the concentration of CUOCPs in the water and sediments of XJ ranged from 2.33 to 6.40 ng L^-1 (average of 3.93 ± 1.15 ng L^-1) and from 1.52 to 21.2 ng g^-1 (average of 6.60 ± 4.31 ng g^-1 dw), respectively. The distribution of CUOCPs in water was consistent throughout XJ, but that in sediments was not uniform, indicating a stronger impact of floods on water than on sediments. Water-sediment partition coefficients were generally >2 L g^-1, showing a tendency of CUOCP dominance in sediments. The results of principal component analysis and cluster analysis showed that the occurrence of CUOCPs is significantly affected by exogenous disturbance, which could be flood events; meanwhile, clusters of CUOCPs were found in both water and sediments in the source-limited middle reaches in urban areas. Redundancy analysis (RDA) showed that CUOCP occurrences were not positively correlated with nutrient elements (nitrogen and phosphorus), but related to pH and dissolved oxygen (DO), indicating complex sources.

Spatial and temporal variation, source identification, and toxicity evaluation of brominated/chlorinated/nitrated/oxygenated-PAHs at a heavily industrialized area in eastern China

Some derivatives of polycyclic aromatic hydrocarbons (PAHs) such as chlorinated and brominated PAHs (Cl/BrPAHs), nitrated and oxygenated PAHs (N/OPAHs) have attracted significant concern due to their high toxicity. Knowledge of the profiles, formation mechanisms, and potential sources of these toxic chemicals near the industrial complexes is essential for their pollution control and management. In this study, we monitored Cl/BrPAHs, N/OPAHs, and PAHs at 24 sampling sites near a heavily industrialized area (steel, chemical, and rubber plants) using passive air samplers during the heating period (7 December 2019 to 15 April 2020) and the non-heating period (2 June 2020 to 4 October 2020). The total average concentrations of 16 BrPAHs, 8 ClPAHs, 17 NPAHs, 6 OPAHs, and 18 PAHs during both sampling periods were 471 pg/m³, 229 pg/m³, 312 pg/m³, 2120 pg/m³, and 63.1 ng/m³, respectively. Except for NPAHs, BrPAHs, ClPAHs, OPAHs, and PAHs all showed higher levels during the heating period. The spatial distributions of Cl/BrPAHs, N/OPAHs, and PAHs exhibited a similar pattern, with the highest concentrations detected in the vicinity of the steel industry. Congener profiles of PAH derivatives indicated that mono-substituted low molecular weight compounds (2-3 rings) were dominant. The major formation mechanisms of halogenated PAHs were discussed by correlation analysis and relative Gibbs free energies, and direct bromination of parent PAHs could be the major formation mechanism of BrPAHs in this study. Diagnostic ratios showed that NPAHs were mainly derived from primary emissions, but the contribution of secondary formation was increased at heavily contaminated sites. The positive matrix factorization model extracted four Cl/BrPAHs, three N/OPAHs, and four PAHs factors, and the result showed that PAHs and their derivatives mainly derived from industrial and combustion sources, photochemical reactions, vehicle emissions, and crude oil volatilization, etc.

PM2.5-bound phthalates and phthalate substitutes in a megacity of southern China: spatioseasonal variations, source apportionment, and risk assessment

Plasticizers are ubiquitous pollutants in the environment, whereas few efforts have been made to elucidate their emission sources in the atmosphere. In this research, the spatioseasonal variations and sources of particle-bound (PM_2.5) phthalates (PAEs) and their substitutes (APs) at residential sites in seven districts and at four potential point-source sites across a megacity in South China were revealed. The total concentrations of PAEs ranging from 10.7 to 528 ng/m³ were substantially higher than those of APs (1.45.58.5 ng/m³). Significant spatial variations in the concentrations of the pollutants were observed, which were generally higher at the sites with intensive industrial activities and the point-source sites. Most atmospheric plasticizer levels peaked in summer, probably due to the temperature-promoted volatilization. Seven sources of plasticizers were identified by the positive matrix factorization (PMF) model. The sources in less industrialized districts are mainly associated with domestic and commercial emissions and with industry in the industrialized districts. Specifically, plastics and personal care products together contributed 60% of the plasticizers in the atmosphere of this city, followed by solvents and polyester industry sources. The incremental lifetime cancer risk of inhalation exposure to bis(2-ethylhexyl) phthalate in the study city is below the acceptable level. Relatively higher risks were found for residents living around sites with intensive industrial activities and around wastewater treatment plant.

Profiling of seasonal variation in and cancer risk assessment of benzo(a)pyrene and heavy metals in drinking water from Kirkuk city, Iraq

Water samples at 13 sites were analyzed to evaluate heavy metals (cobalt, lead, manganese, copper) and benzo(a)pyrene using 2 methods of analysis (high-performance liquid chromatography (HPLC) and enzyme-linked immunosorbent assay (ELISA) kits). The Lesser Zap River is the main tributary of the Tigris and is used as a main source of drinking water in Kirkuk city through the General Kirkuk project. Risk evaluation for benzo(a)pyrene and lead in water samples was accomplished by Monte Carlo simulation. The highest concentrations of B(a)P were recorded at sites S7 and S5, with levels of 0.192 and 0.122 µg L^-1 detected by HPLC and ELISA, respectively. The WHO guidelines for benzo[a]pyrene in drinking water recommend 0.7 µg L ^-1, and none of the samples surpassed this level; moreover, B(a)P levels exceeded EPA standards in 2014 (0.01 µg L^-1), particularly when the liquid-liquid extraction method with HPLC was used. Carcinogenic risks for human adults and children exist and are highest during the rainy season as compared with the carcinogenic risk during the dry season and risks for children exceed those of adults. This indicates that the 2^nd round of sampling (winter season) harbors more carcinogenic risk than the 1^st round of sampling (dry season).

Spatial and seasonal variations of PAHs in soil, air, and atmospheric bulk deposition along the plain to mountain transect in Hubei province, central China: Air-soil exchange and long-range atmospheric transport

Polycyclic aromatic hydrocarbons (PAHs) are a long-term environmental problem faced by human society. The sources of involuntary PAHs are complex, moreover, secondary emissions of fixed PAHs in the environment occur due to global change and disturbance of human activities. Samples of three environmental media including soil, air, and atmospheric bulk deposition were collected to observe the spatial distribution and seasonal variation, to discuss the source or sink of PAHs and their association with the air mass transport along the plain (Jianghan Plain, JHP) to mountain transect, and explore the geographic scope of the atmospheric transport influence. The results obtained showed that 16 individual PAHs generally existed in all environmental multimedia being studied, and the PAHs concentration in air, soil and deposition flux of atmospheric bulk was higher in JPH than in "Western Hubei Mountains" (WHMs). Considerably high PAHs concentrations were obtained from the soil, air and atmospheric bulk deposition in winter, summer, and both summer and winter, respectively. The air-soil fugacity fraction of PAHs indicated that the soil of Dajiuhu (DJH) is likely to be a sink. Backward air trajectory simulation confirmed that most of the air mass passes over the JHP before reaching DJH, combined with the (transport and persistence level III) TaPL3 model results JHP are acting as sources. However, seasonal changes lead to a shift in the roles of soil sources and sinks. The TaPL3 model calculated that PAHs are transported through water for a wider range of effects and a longer persistence, even up to 10 years.

Indoor Particulate Matter in Urban Households: Sources, Pathways, Characteristics, Health Effects, and Exposure Mitigation

Particulate matter (PM) is a complex mixture of solid particles and liquid droplets suspended in the air with varying size, shape, and chemical composition which intensifies significant concern due to severe health effects. Based on the well-established human health effects of outdoor PM, health-based standards for outdoor air have been promoted (e.g., the National Ambient Air Quality Standards formulated by the U.S.). Due to the exchange of indoor and outdoor air, the chemical composition of indoor particulate matter is related to the sources and components of outdoor PM. However, PM in the indoor environment has the potential to exceed outdoor PM levels. Indoor PM includes particles of outdoor origin that drift indoors and particles that originate from indoor activities, which include cooking, fireplaces, smoking, fuel combustion for heating, human activities, and burning incense. Indoor PM can be enriched with inorganic and organic contaminants, including toxic heavy metals and carcinogenic volatile organic compounds. As a potential health hazard, indoor exposure to PM has received increased attention in recent years because people spend most of their time indoors. In addition, as the quantity, quality, and scope of the research have expanded, it is necessary to conduct a systematic review of indoor PM. This review discusses the sources, pathways, characteristics, health effects, and exposure mitigation of indoor PM. Practical solutions and steps to reduce exposure to indoor PM are also discussed.

Interfacial interaction between benzo[a]pyrene and pulmonary surfactant: Adverse effects on lung health

Inhaled polycyclic aromatic hydrocarbons (PAHs) can directly interact with the lung surfactant (PS) lining of alveoli, thereby affecting the normal physiological functions of PS, which is a serious threat to lung health. In spite of the extensive study of benzo[a]pyrene (BaP, a representative of PAHs), its potential biophysical influence on the natural PS is still largely unknown. In this study, the interfacial interaction between PS (extracted from porcine lungs) and BaP is investigated in vitro. The results showed that the surface tension, phase behavior, and interfacial structure of the PS monolayers were obviously altered in the presence of BaP. A solubilization test manifested that PS and its major components (dipalmitoyl phosphatidylcholine, DPPC; bovine serum albumin, BSA) could in turn accelerate the dissolution of BaP, which followed the order: PS > DPPC > BSA, and mixed phospholipids were significantly responsible for the solubilization of BaP by PS. In addition, solubilization of BaP also enhanced the consumption of hydroxyl radicals (·OH) in the simulated lung fluid, which could disturb the balance between oxidation and antioxidation.

A rapid Soxhlet and mini-SPE method for analysis of polycyclic aromatic hydrocarbons in atmospheric particles

An analytical method was validated with two reference materials of polycyclic aromatic hydrocarbons in atmospheric particles. Standard reference materials (SRMs) were incorporated into the matrix of unexposed cut quartz filters. The methodology was previously designed and extraction of polycyclic aromatic hydrocarbons (PAHs) from fortified filters was based on a rapid low-cost method, for a low consumption of volume and time. The optimisation combined a low-volume Soxhlet apparatus used in hot Soxhlet mode with a quick clean-up by solid-phase extraction with special cartridges. The quantification of target compounds was performed by gas chromatography/mass spectroscopy in SIM mode. Temperatures of injector and oven program of the GC-MS were also optimised. Experimental variables of both systems were successfully optimised and validated, achieving a robust analytical methodology.

Atmospheric particle-bound polycyclic aromatic hydrocarbons, n-alkanes, hopanes, steranes and trace metals: PM2.5 source identification, individual and cumulative multi-pathway lifetime cancer risk assessment in the urban environment

The occurrence of atmospheric fine particles (PM_2.5)-associated polycyclic aromatic hydrocarbons (PAHs), trace metals and organic molecular markers was investigated by conducting an intensive sampling campaign at the Eastern Mediterranean urban area of Nicosia (Cyprus). Sixty-two 24-hr PM_2.5 samples were collected and analyzed for fifty parent and alkylated PAHs, twenty-five long chain n-alkanes, seventeen hopanes and twelve steranes used for source apportionment. The same number and kind of samples were analyzed to determine twenty-eight trace metals. Emphasis was given to investigate the air levels of the scarcely monitored although highly carcinogenic PAHs such as dibenzopyrenes, dibenzoanthracenes, 7H-benzo[c]fluorene and 5-methyl-chrysene, not included in the USEPA's sixteen PAH priority list (USEPA-16). UNMIX receptor model was applied to apportion the sources of atmospheric emissions of the determined organic compounds and trace metals and evaluate their daily contributions to the corresponding PM_2.5 associated concentrations. For comparison purposes, principal component analysis with multiple linear regression (PCA/MLR) was also applied and its results are reported. The UNMIX receptor model, compared to PCA/MLR, offered a more precise source profile and more reliable daily mass source distributions by eliminating negative contributions. The individual and cumulative multi-pathway lifetime cancer risk (posed via inhalation, ingestion and dermal contact) by exposure to PM_2.5-associated USEPA-16 listed and non-listed PAHs and selected airborne trace metals (As, Cd, Co, Ni, and Pb) were assessed. To estimate the contribution of each emission source to the total cancer risk, multiple linear regression analysis was performed, using as independent variables the daily source mass contributions and as dependent variables the respective cancer risk units. The estimated total cumulative cancer risk comprising all toxic PAHs, besides those included in the priority list, and metals was higher than the USEPA's threshold by a factor of eight, denoting a potential risk for long-term exposure of a population in the urban environment.

Passive air sampling for semi-volatile organic chemicals

During passive air sampling, the amount of a chemical taken up in a sorbent from the air without the help of a pump is quantified and converted into an air concentration. In an equilibrium sampler, this conversion requires a thermodynamic parameter, the equilibrium sorption coefficient between gas-phase and sorbent. In a kinetic sampler, a time-averaged air concentration is obtained using a sampling rate, which is a kinetic parameter. Design requirements for kinetic and equilibrium sampling conflict with each other. The volatility of semi-volatile organic compounds (SVOCs) varies over five orders of magnitude, which implies that passive air samplers are inevitably kinetic samplers for less volatile SVOCs and equilibrium samplers for more volatile SVOCs. Therefore, most currently used passive sampler designs for SVOCs are a compromise that requires the consideration of both a thermodynamic and a kinetic parameter. Their quantitative interpretation depends on assumptions that are rarely fulfilled, and on input parameters, that are often only known with high uncertainty. Kinetic passive air sampling for SVOCs is also challenging because their typically very low atmospheric concentrations necessitate relatively high sampling rates that can only be achieved without the use of diffusive barriers. This in turn renders sampling rates dependent on wind conditions and therefore highly variable. Despite the overall high uncertainty arising from these challenges, passive air samplers for SVOCs have valuable roles to play in recording (i) spatial concentration variability at scales ranging from a few centimeters to tens of thousands of kilometers, (ii) long-term trends, (iii) air contamination in remote and inaccessible locations and (iv) indoor inhalation exposure. Going forward, thermal desorption of sorbents may lower the detection limits for some SVOCs to an extent that the use of diffusive barriers in the kinetic sampling of SVOCs becomes feasible, which is a prerequisite to decreasing the uncertainty of sampling rates. If the thermally stable sorbent additionally has a high sorptive capacity, it may be possible to design true kinetic samplers for most SVOCs. In the meantime, the passive air sampling community would benefit from being more transparent by rigorously quantifying and explicitly reporting uncertainty.

Atmospheric concentration, source identification, and health risk assessment of persistent organic pollutants (POPs) in two countries: Peru and Turkey

It is known that some persistent organic pollutants (POPs) are used worldwide, and these pollutants are dangerous for human health. However, there are still countries where measurements of these pollutants have not been adequately measured. Although many studies have been published for determining the concentrations of POPs in Turkey, there are limited studies in Latin American countries like Peru. For this reason, it is essential both to conduct a study in Peru and to compare the study with another country. This study is aimed at determining the atmospheric POPs such as polycyclic aromatic hydrocarbon (PAH), organochlorine pesticide (OCP), and polychlorinated biphenyl (PCB) concentrations using passive air samplers in Yurimaguas (Peru) and Bursa (Turkey). Molecular diagnosis ratios and ring distribution methods were used to determine the sources of PAHs. According to these methods, coal and biomass combustions were among the primary sources of PAHs in Peru, while petrogenic and petroleum were the primary sources of PAHs in Turkey. Then, α-HCH/γ-HCH and β-/(α+γ)-HCH ratios were used to determine the sources of OCPs. According to the α-HCH/γ-HCH ratios, the primary sources of OCPs in both countries were lindane. Similarly, according to β-/(α+γ)-HCH ratios, the HCHs have been historically used in Peru while they were recently utilized in Turkey. Finally, homologous group distributions were used to determine the sources of PCBs. Similar distributions of homologous groups were observed in the sampling sites in both countries. Also, the homologous group distributions obtained have been determined that industrial activities could be effective in the sampling areas in both countries. When the cancer risks that could occur via inhalation were evaluated, no significant cancer risk has been determined in both countries.

Total p-PAH Levels Nearby a Complex Industrial Area: A Tailored Monitoring Experiment to Assess the Impact of Emission Sources

In this study, data on the hourly concentrations of the total particle-bound Polycyclic Aromatic Hydrocarbons (p-PAHs) collected between 1 August 2013 and 31 August 2014 by the air quality fence monitoring network of the biggest European steel plant, were analyzed. In contrast with what was predicted, the total p-PAH concentration did not decrease with distance from the steel plant, and higher concentrations were registered at the Orsini site, in the urban settlement, relative to the Parchi site, which is nearest to the coke ovens. Therefore, in order to identify and explain the cause of these high concentrations, a tailored monitoring experiment was carried out on a specific monitoring pathway by using a total p-PAHs monitor placed onto a cart. The real-time monitoring of the total p-PAH concentration on the road revealed to be a useful tool, which identified vehicular traffic as an important source of p-PAHs and highlighted the possible high short-term effect that vehicular traffic sources could have on the health of the exposed human population. Moreover, the study focused attention on the importance of the spatial representativeness of fixed monitoring stations, especially in a highly complex industrial area such as Taranto (Southern Italy).