Enhanced uranium removal from acidic wastewater by phosphonate-functionalized ordered mesoporous silica: Surface chemistry matters the most

Phytic acid-functionalized polyamidoxime/alginate hydrogel for targeted uranium extraction from acidic wastewater

Efficient removal of uranium from radioactive wastewater is crucial for both environmental protection and sustainable development of nuclear energy. However, selectively extracting uranium from acidic wastewater remains a significant challenge. Here we present a phytic acid-functionalized polyamidoxime/alginate hydrogel (PAG) via a facile one-step hydrothermal reaction. The PAG, leveraging the robust binding affinity of phytic acid and the selective coordination of amidoxime for U(VI), exhibited high efficiency and selectivity in adsorbing U(VI) from acidic uranium-containing wastewater. At pH 2.50, U(VI) adsorption equilibrium was achieved within 60 min, showcasing a maximum theoretical adsorption capacity of 218.34 mg/g. Additionally, the PAG demonstrated excellent reusability, maintaining a uranium removal rate exceeding 90 % over five adsorption-desorption cycles. Remarkably, the as-synthesized PAG removed 94.1 % of U(VI) from actual acidic uranium-contaminated groundwater with excellent anti-interference performance, reducing U(VI) concentration from 272.0 μg/L to 16.1 μg/L and making it meet the WHO drinking water standards (30 μg/L). The adsorption mechanism was elucidated through XPS and DFT calculation, revealing that the uranyl ion primarily coordinated with phosphate and amidoxime groups on phytic acid and polyamidoxime, respectively. These findings underscore the promising potential of PAG hydrogel for addressing acidic uranium-containing wastewater from uranium mining and metallurgy.

Green preparation of regenerable biohybrids with xanthan gum-stabilized biogenic mackinawite nanoparticles for efficient treatment from high-concentration uranium wastewater

The high efficiency, economy, sustainability and no secondary pollution of U(VI) removal is an important and challenging topic for U(VI) wastewater treatment. Here, the regenerable biohybrids with xanthan gum (XG) stabilized biogenic mackinawite nanoparticles (BX-FeS) were prepared, where XG acted as carrier facilitated the Fe2+ attachment and induced the low size, high stability and activity of nearly spherical FeS nanoparticles. Results showed that BX-FeS kept high activity after storing two years and good performance for U(VI) removal in broad pH range and co-existence of ions, and had greater removal efficiency (97.9 %) than biogenic B-FeS (67.1 %). Moreover, BX-FeS preformed high adsorption capacity in uranium wastewater (658.0 mg/g), and lower cost compared with zerovalent-iron and silica gel. Importantly, BX-FeS maintained high activity within three regeneration cycles driven by Desulfovibrio desulfuricans, inhibited the secondary pollution (Fe3+, SO42-) of reaction. This study provides a new strategy for sustainable and efficient treatment of U(VI) wastewater.

One particle three targets: Phosphate anion-modified magnetic mesoporous silica with enhanced fluorescence for sensitive detection, efficient adsorption, and repeated removal of uranium (VI) ions

An ideal adsorbent material that combines the multiple capabilities of sensitive detection, efficient adsorption, and repeatable removal of uranium (U) from the environment remains a serious challenge. Herin, a general method was developed for synthesizing a series of phosphate anions (such as: PO43-, P2O74-, P3O105- and P6O186-) modified magnetic mesoporous silica nanoparticles (Fe3O4 @mSiO2-Zn2+ NPs). The mesoporous surfaces and abundant phosphate groups provide potential, powerful uranium-binding sites for capturing U(VI) ions. Especially, the optimum adsorption capacity of Fe3O4 @mSiO2-Zn2+/P3O105- NPs was as high as 885.90 mg·g-1 (298 K), which was higher than that of unmodified or other phosphate anions-modified Fe3O4 @mSiO2-Zn2+ NPs. Meanwhile, P3O105--binding sites and mesoporous surfaces also strongly restrict U(VI) ions' fluorescence vibrational inactivation, the adsorption results in rapid green fluorescence enhancement (within 180 s), and an ultra-low detection limit (4.5 nmol·L-1), which is well below the standard in drinking water of the World Health Organization (WHO). Furthermore, even after 5 cycles, the adsorbent still maintained their original adsorption capacity of 80.21% and displayed excellent selectivity for detecting and removing U(VI) from seawater. Based on these results, the Fe3O4 @mSiO2-Zn2+/P3O105- NPs seem to be a suitable multifunctional adsorbent for the detection, adsorption, and removal of U(VI) from environment.

Iodide ion-imprinted chitosan beads for highly selective adsorption for nuclear wastewater treatment applications

Iodide ions from radioactive iodine isotopes are common contaminants present in nuclear wastewater from nuclear power plants which are considered hazardous contaminants to be released in water sources even at low concentrations due to their association with metabolic disorders, therefore its removal from the nuclear wastewater effluents is necessary. Chitosan beads are natural and cost-efficient adsorbents that have been used for ion removal from wastewater. However, issues of poor selectivity persist in achieving high-efficiency iodide ion removal. In this study, ion-imprinted chitosan beads (IIC) have been synthesized using the phase-inversion method, IIC beads were modified by cross-linking with epichlorohydrin (IIC-EPI) and modified by cross-linking with epichlorohydrin and silicon dioxide nanoparticles (IIC-SiO2-EPI). Through 4 h of batch adsorption experiments, IIC beads achieved a maximum adsorption capacity (Qe) of 0.65 mmol g-1 and showed more preference for the iodide ions compared to the non-imprinted chitosan beads which achieved a maximum adsorption capacity of 0.27 mmol g-1 at pH 7. While the modified beads IIC-EPI and IIC-SiO2-EPI beads have boosted the adsorption capacities to 0.72 mmol g-1 and 0.91 mmol g-1. Scanning electron microscopic cross-sectional images have shown more pores and cavities than the surface images which agrees with the multilayer heterogeneous diffusion suggested by the Freundlich adsorption isotherm, that the experimental data has fitted. Adsorption kinetic data have fitted the Pseudo-second-order model as well as the Weber and Morris intraparticle model, which suggest an intraparticle pore diffusion adsorption mechanism, with the involvement of the physical electrostatic interactions with the cationic chitosan surface.

Multifunctional mesoporous silica nanoparticles for biomedical applications

Mesoporous silica nanoparticles (MSNs) are recognized as a prime example of nanotechnology applied in the biomedical field, due to their easily tunable structure and composition, diverse surface functionalization properties, and excellent biocompatibility. Over the past two decades, researchers have developed a wide variety of MSNs-based nanoplatforms through careful design and controlled preparation techniques, demonstrating their adaptability to various biomedical application scenarios. With the continuous breakthroughs of MSNs in the fields of biosensing, disease diagnosis and treatment, tissue engineering, etc., MSNs are gradually moving from basic research to clinical trials. In this review, we provide a detailed summary of MSNs in the biomedical field, beginning with a comprehensive overview of their development history. We then discuss the types of MSNs-based nanostructured architectures, as well as the classification of MSNs-based nanocomposites according to the elements existed in various inorganic functional components. Subsequently, we summarize the primary purposes of surface-functionalized modifications of MSNs. In the following, we discuss the biomedical applications of MSNs, and highlight the MSNs-based targeted therapeutic modalities currently developed. Given the importance of clinical translation, we also summarize the progress of MSNs in clinical trials. Finally, we take a perspective on the future direction and remaining challenges of MSNs in the biomedical field.

Efficient removal of uranium (VI) from water by a hyper-cross-linked polymer adsorbent modified with polyethylenimine via phosphoramidate linkers

Practical adsorbents with high efficiency are essential to effectively treating wastewater. Herein, a novel porous uranium adsorbent (PA-HCP) having a considerable amount of amine and phosphoryl groups was designed and synthesized by grafting polyethyleneimine (PEI) on a hyper-cross-linked fluorene-9-bisphenol skeleton via phosphoramidate linkers. Furthermore, it was used to treat uranium contamination in the environment. PA-HCP exhibited a large specific surface area (up to 124 m2/g) and a pore diameter of 2.5 nm. Batch uranium adsorptions on PA-HCP were investigated methodically. PA-HCP demonstrated a uranium sorption capacity of >300 mg/g in the pH range of 4-10 (C0 = 60 mg/L, T = 298.15 K), with its maximum capacity reaching 573.51 mg/g at pH = 7. The uranium sorption process obeyed the pseudo-second-order model and fitted well with the Langmuir isothermal. In the thermodynamic experiments, uranium sorption on PA-HCP was revealed to be an endothermic, spontaneous process. Even in the presence of competing metal ions, PA-HCP exhibited excellent sorption selectivity for uranium. Additionally, excellent recyclability can be achieved after six cycles. Based on FT-IR and XPS measurements, both the PO and -NH2 (and/or -NH-) groups on PA-HCP contributed to efficient uranium adsorption as a result of the strong coordination between these groups and uranium. Furthermore, the high hydrophilicity of the grafted PEI improved the dispersion of the adsorbents in water and facilitated uranium sorption. These findings suggest that PA-HCP can be used as an efficient and economical sorbent to remove U(VI) from wastewater.

Optimal Synthesis of Novel Phosphonic Acid Modified Diatomite Adsorbents for Effective Removal of Uranium(VI) Ions from Aqueous Solutions

The authors synthesized a series of functionalized diatomite-based materials and assessed their U(VI) removal performance. Phosphor-derivative-modified diatomite adsorbents were synthesized by the three-route procedures: polymerisation (DIT-Vin-PAin), covalent (DIT-Vin-PAcov), and non-covalent (DIT-PA) immobilization of the functional groups. The effects of the diatomite modification have been studied using powder XRD, solid state NMR, FTIR spectroscopy, electronic microscopy, EDX, acid-base titrations, etc. The maximum adsorption capacities of DIT-Vin-PAcov, DIT-PA, and DIT-Vin-PAin samples were 294.3 mg/g, 253.8 mg/g, and 315.9 mg/g, respectively, at pH0 = 9.0. The adsorption amount of U(VI) ions using the prepared DIT-Vin-PAin was 95.63%, which is higher compared with that of the natural diatomite at the same concentration. The adsorption studies demonstrated that the phosphonic and hydroxyl groups on the surface of the diatomite played pivotal roles in the U(VI) adsorption. The U(VI) ions as a "hard" Lewis acid could easily form bonds with the "hard" donor P-containing ligands, so that the as-prepared DIT-Vin-PAin sample had excellent adsorption properties. The monolayer adsorption of the analyte on the surface of the raw diatomite and DIT-PA was observed. It was found from the thermodynamic parameters that the uptake of the U(VI) ions by the obtained adsorbents was a spontaneous process with an endothermic effect. Findings of the present work highlight the potential for using modified diatomite as effective and reusable adsorbents for the extraction of U(VI) in the waste, river, and tap waters with satisfactory results.

Polyphosphonate-segmented macroporous organosilicon frameworks for efficient dynamic enrichment of uranium with in-situ regeneration

Efficient separation and enrichment of uranium from radioactive effluents is of strategic significance for sustainable development of nuclear energy and environmental protection. Macropore structure of adsorbent is conducive to accessibility of the pore and transport of the adsorbate during dynamic adsorption. However, the low specific surface area results in fewer ligand sites and subsequently reduces the adsorption capacity. Herein, we present a novel strategy for efficient dynamic uranium enrichment using polyphosphonate-segmented macroporous organosilicon frameworks (PMOFs). PMOFs are constructed through the copolymerization of diethyl vinylphosphonate and triethoxyvinylsilane, followed by hydrolysis and condensation of the oligomers. The introduction of polyphosphonate segments into the frameworks endows PMOFs with a macroporous structure (31 µm) and a high ligand content (up to 72 wt%). Consequently, the optimized PMOF-3 demonstrated an ultrahigh dynamic adsorption capacity of 114.8 mg/g among covalently conjugated silicon-based materials. Additionally, PMOF-3 achieves a high enrichment factor (120) in the dynamic enrichment of uranium on a fixed bed column, which can be in-situ regenerated with 1 M NaHCO₃ as the eluent. This work presents a new strategy for efficient dynamic enrichment of nuclides, which can be extended to the separation of other specific pollutants, shedding new light on adsorbent design and technical innovation.

Comparative Study of the U(VI) Adsorption by Hybrid Silica-Hyperbranched Poly(ethylene imine) Nanoparticles and Xerogels

Two different silica conformations (xerogels and nanoparticles), both formed by the mediation of dendritic poly (ethylene imine), were tested at low pHs for problematic uranyl cation sorption. The effect of crucial factors, i.e., temperature, electrostatic forces, adsorbent composition, accessibility of the pollutant to the dendritic cavities, and MW of the organic matrix, was investigated to determine the optimum formulation for water purification under these conditions. This was attained with the aid of UV-visible and FTIR spectroscopy, dynamic light scattering (DLS), ζ-potential, liquid nitrogen (LN₂) porosimetry, thermogravimetric analysis (TGA), and scanning electron microscopy (SEM). Results highlighted that both adsorbents have extraordinary sorption capacities. Xerogels are cost-effective since they approximate the performance of nanoparticles with much less organic content. Both adsorbents could be used in the form of dispersions. The xerogels, though, are more practicable materials since they may penetrate the pores of a metal or ceramic solid substrate in the form of a precursor gel-forming solution, producing composite purification devices.

Removal of 241Am from Aqueous Solutions by Adsorption on Sponge Gourd Biochar

Luffa cylindrica biomass was converted to biochar and the removal of 241Am by pristine and oxidized biochar fibers was investigated in laboratory and environmental water samples. This species has the added advantage of a unique microsponge structure that is beneficial for the production of porous adsorbents. The main purpose of this study was to valorize this biomass to produce an efficient adsorbent and investigate its performance in radionuclide-contaminated waters. Following the preparation of Am3+ solutions at a concentration of 10−12 mol/L, the adsorption efficiency (Kd) was determined as a function of pH, adsorbent mass, ionic strength, temperature, and type of aqueous solution by batch experiments. At the optimum adsorbent dose of 0.1 g and pH value of 4, a log10Kd value of 4.2 was achieved by the oxidized biochar sample. The effect of temperature and ionic strength indicated that adsorption is an endothermic and entropy-driven process (ΔH° = −512 kJ mol−1 and ΔS° = −1.2 J K−1 mol−1) leading to the formation of inner-sphere complexes. The adsorption kinetics were relatively slow (24 h equilibrium time) due to the slow diffusion of the radionuclide to the biochar surface and fitted well to the pseudo-first-order kinetic model. Oxidized biochar performed better compared to the unmodified sample and overall appears to be an efficient adsorbent for the treatment of 241Am-contaminated waters, even at ultra-trace concentrations.

Highly effective sustainable membrane based cyanobacteria for uranium uptake from aqueous environment

Wastewater from industrial process of uranium ore mining contains a large amount of this radioactive pollutant. Regarding the advantages of biosorption, it was found that varieties of biomasses such as agricultural waste, algae and fungi are effective for uranium removal. However, there is limited research on cyanobacteria, therefore, cyanobacteria, Anagnostidinema amphibium (CAA) was investigated by batch method for the first time for biosorption of uranium (VI). Optimization of biosorption parameters showed that maximum removal efficiency of 92.91% was reached at pH range of 9-11 with 50 mg of cyanobacteria to 100 mg/L U(VI) initial concentration, at 25 °C within 40 min. Used biosorbent exhibited very good selectivity for U(VI) ions and reusability in IV sorption/desorption cycles. Characterization of CAA surface was performed by FTIR, EDS, EDXRF and SEM analysis and it has shown various functional groups (CONH, COOH, OH, PO alkyl group) and that it is very rich in elements such as iron, potassium and calcium. In binary systems, contained of U(VI) and selected ions, CAA exhibits very good selectivity towards U(VI) ions. Kinetic data revealed the best accordance of experimental data with the pseudo-second-order model and isotherms data agreed with Freundlich model. Thermodynamic data implied that U(VI) biosorption process by A. amphibium exhibited spontaneity and modelling of the investigated process showed that the adsorption of uranium ions occurs mainly via peptidoglycan carboxyl groups. Overall results show that these cyanobacteria with a maximum sorption capacity of 324.94 mg/g have great potential for the processing of wastewater polluted with uranium (VI).

Uranium Removal from Aqueous Solutions by Aerogel-Based Adsorbents-A Critical Review

Aerogels are a class of lightweight, nanoporous, and nanostructured materials with diverse chemical compositions and a huge potential for applications in a broad spectrum of fields. This has led the IUPAC to include them in the top ten emerging technologies in chemistry for 2022. This review provides an overview of aerogel-based adsorbents that have been used for the removal and recovery of uranium from aqueous environments, as well as an insight into the physicochemical parameters affecting the adsorption efficiency and mechanism. Uranium removal is of particular interest regarding uranium analysis and recovery, to cover the present and future uranium needs for nuclear power energy production. Among the methods used, such as ion exchange, precipitation, and solvent extraction, adsorption-based technologies are very attractive due to their easy and low-cost implementation, as well as the wide spectrum of adsorbents available. Aerogel-based adsorbents present an extraordinary sorption capacity for hexavalent uranium that can be as high as 8.8 mol kg−1 (2088 g kg−1). The adsorption data generally follow the Langmuir isotherm model, and the kinetic data are in most cases better described by the pseudo-second-order kinetic model. An evaluation of the thermodynamic data reveals that the adsorption is generally an endothermic, entropy-driven process (ΔH0, ΔS0 > 0). Spectroscopic studies (e.g., FTIR and XPS) indicate that the adsorption is based on the formation of inner-sphere complexes between surface active moieties and the uranyl cation. Regeneration and uranium recovery by acidification and complexation using carbonate or chelating ligands (e.g., EDTA) have been found to be successful. The application of aerogel-based adsorbents to uranium removal from industrial processes and uranium-contaminated waste waters was also successful, assuming that these materials could be very attractive as adsorbents in water treatment and uranium recovery technologies. However, the selectivity of the studied materials towards hexavalent uranium is limited, suggesting further developments of aerogel materials that could be modified by surface derivatization with chelating agents (e.g., salophen and iminodiacetate) presenting high selectivity for uranyl moieties.

Characteristic Aspects of Uranium(VI) Adsorption Utilizing Nano-Silica/Chitosan from Wastewater Solution

A new nano-silica/chitosan (SiO₂/CS) sorbent was created using a wet process to eliminate uranium(VI) from its solution. Measurements using BET, XRD, EDX, SEM, and FTIR were utilized to analyze the production of SiO₂/CS. The adsorption progressions were carried out by pH, SiO₂/CS dose, temperature, sorbing time, and U(VI) concentration measurements. The optimal condition for U(VI) sorption (165 mg/g) was found to be pH 3.5, 60 mg SiO₂/CS, for 50 min of sorbing time, and 200 mg/L U(VI). Both the second-order sorption kinetics and Langmuir adsorption model were observed to be obeyed by the ability of SiO₂/CS to eradicate U(VI). Thermodynamically, the sorption strategy was a spontaneous reaction and exothermic. According to the findings, SiO₂/CS had the potential to serve as an effectual sorbent for U(VI) displacement.

Surface ion-imprinted brewer's spent grain with low template loading for selective uranyl ions adsorption from simulated wastewater

Efficient removal of uranyl ions from wastewater requires excellent selectivity of the adsorbents. Herein, we report a new strategy using a high monomer/template molar ratio of 500:1 to prepare surface ion-imprinted brewer's spent grain (IIP-BSG) for selective U(VI) removal using binary functional monomers (2-hydroxyethyl methacrylate and diethyl vinylphosphonate) with high site accessibility and easy template removal. IIP-BSG exhibits a maximum U(VI) adsorption capacity of 165.7 mg/g, a high selectivity toward U(VI) in the presence of an excess amount of Eu(III) (Eu/U molar ratio = 20), a good tolerance of salinity, and a high reusability. In addition, mechanism studies have revealed electrostatic interaction and a coordination of uranyl ions by carboxyl and phosphoryl groups, the predominant contribution of high-energy (specific) sites during selective adsorption, and internal mass transfer as the rate-controlling step of U(VI) adsorption. Furthermore, IIP-BSG shows great potentials to separate U(VI) from lanthanides in simulated nuclear wastewater (pH₀ = 3.5) and selectively concentrate U(VI) from simulated mine water (pH₀ = 7.1). This study proves that the ion-imprinting effect can be achieved using a very low template amount with reduced production cost and secondary pollution, which benefits large-scale promotion of the ion-imprinted materials for selective uranyl ions removal.

Shear-induced fabrication of SiO2 nano-meshes for efficient uranium capture

The extraction of uranium from seawater and the safe treatment of wastewater containing uranium (VI) were important to ensure the sustainable development of nuclear-related energy sources. Two-dimensional silica nanomaterials have been extensively investigated in the field of uranium adsorption due to their high adsorption capacity, short equilibration times, and easily modified surface groups. However, the two-dimensional mesoporous silica nanomaterial preparation has become a challenge due to the lack of natural sheet templating agents. The reason will hinder the development of silica nanomaterials for uranium extraction. Here, the specific surface area silica nanomeshes (HSMSMs) uranium adsorbent was prepared by a high shear method to induce nanobubble formation. HSMSMs showed a high uranium adsorption capacity of 822 mg_-U/g_-abs in seawater with the uranium adsorption concentration was 50 mg/L, which was approximately 2 times higher than the conventional mesoporous silica nanomaterials. Compared to HSMSMs, the amidoxime-modified high specific surface area silica nanomesh (HSMSMs-AO) demonstrated good selectivity for U(VI), and the uranium ions uptake was 877 mg_-U/g_-abs in 50 mg/L uranium-spiked simulated seawater. Due to HSMSMs-AO's stable chemical properties and high mechanical strength, HSMSMs-AO also displayed long service life. Benefiting from the simple preparation method and high adsorption capacity of HSMSMs, HSMSMs could be a promising candidate for large-scale extraction of uranium from seawater.

Ecofriendly Composite as a Promising Material for Highly-Performance Uranium Recovery from Different Solutions

The development of new materials based on biopolymers (as renewable resources) is substantial for environmental challenges in the heavy metal and radionuclide ions removal contaminations. Functionalization of chitosan with sulfonic groups was achieved for improving the uranium sorption, not only from slightly acidic leachate, but also for the underground water. The prepared hydrogel based on chitosan was characterized by series of analysis tools for structure elucidation as FTIR spectroscopy, textural properties using nitrogen adsorption method, pH_PZC (by pH-drift method), thermogravimetric analysis (TGA), SEM, and SEM-EDX analyses. The sorption was performed toward uranium (VI) ions for adjustment of sorption performances. The optimum sorption was performed at pH 4 (prior to the precipitation pH). The total sorption was achieved within 25 min (relatively fast kinetics) and was fitted by pseudo-first order rate equation (PFORE) and resistance to intraparticle diffusion equation (RIDE). The maximum sorption capacity was around 1.5 mmol U g^-1. The sorption isotherms were fitted by Langmuir and Sips equations. Desorption was achieved using 0.3 M HCl solution and the complete desorption was performed in around 15 min of contact. The sorption desorption cycles are relatively stable during 5 cycles with limit decreasing in sorption and desorption properties (around 3 ± 0.2% and 99.8 ± 0.1%, respectively). The sorbent was used for removal of U from acid leachate solution in mining area. The sorbent showed a highly performance for U(VI) removal, which was considered as a tool material for radionuclides removing from aquatic medium.

Highly selective extraction of uranium from wastewater using amine-bridged diacetamide-functionalized silica

A major environmental concern related to nuclear energy is wastewater contaminated with uranium, thus necessitating the development of pollutant-reducing materials with efficiency and effectiveness. Herein, highly selective mesoporous silicas functionalized with amine-bridged diacetamide ligands SBA-15-ABDMA were prepared. Different spectroscopy techniques were used to probe the chemical environment and reactivity of the chelating ligands before and after sorption. The results showed that the functionalized SBA-15-ABDMA had a strong affinity for uranium at low pH (pH = 3) with desirable sorption capacity (68.82 mg/g) and good reusability (> 5). It showed excellent separation performance with a high distribution coefficient (K_d,U > 10⁵ mL/g) and separation factors SF_U/Ln > 1000 at a pH of 3.5 in the presence of lanthanide nuclides, alkaline earth metal and transition metal ions. In particular, SiO₂spheres-ABDMA was used as a column material, which achieved excellent recovery of U(VI) (> 98%) and good reusability for samples of simulated mining and nuclear industries wastewater. XPS and crystallography studies clearly illustrated the tridentate coordination mode of U(VI)/PEABDMA and the mechanism and origin behind the high selectivity for U.

Technological trends in nanosilica synthesis and utilization in advanced treatment of water and wastewater

Water and wastewater treatment applications stand to benefit immensely from the design and development of new materials based on silica nanoparticles and their derivatives. Nanosilica possesses unique properties, including low toxicity, chemical inertness, and excellent biocompatibility, and can be developed from a variety of sustainable precursor materials. Herein, we provide an account of the recent advances in the synthesis and utilization of nanosilica for wastewater treatment. This review covers key physicochemical aspects of several nanosilica materials and a variety of nanotechnology-enabled wastewater treatment techniques such as adsorption, separation membranes, and antimicrobial applications. It also discusses the prospective design and tuning options for nanosilica production, such as size control, morphological tuning, and surface functionalization. Informative discussions on nanosilica production from agricultural wastes have been offered, with a focus on the synthesis methodologies and pretreatment requirements for biomass precursors. The characterization of the different physicochemical features of nanosilica materials using critical surface analysis methods is discussed. Bio-hybrid nanosilica materials have also been highlighted to emphasize the critical relevance of environmental sustainability in wastewater treatment. To guarantee the thoroughness of the review, insights into nanosilica regeneration and reuse are provided. Overall, it is envisaged that this work's insights and views will inspire unique and efficient nanosilica material design and development with robust properties for water and wastewater treatment applications.

U(VI) and Th(IV) recovery using silica beads functionalized with urea- or thiourea-based polymers - Application to ore leachate

Urea and thiourea have been successfully deposited at the surface of silica beads (through one-pot reaction with formaldehyde) for designing new sorbents for U(VI) and Th(IV) recovery (UR/SiO₂ and TUR/SiO₂ composites, respectively). These materials have been characterized by FTIR, titration, elemental analysis, BET, TGA, SEM-EDX for identification of structural and chemical properties, and interpretation of binding mechanisms. Based on deprotonation of reactive groups (amine, carbonyl, or thiocarbonyl) and metal speciation, the optimum pH was ~4. Uptake kinetics was fast (equilibrium within 60-90 min). Although the kinetic profiles are fitted by the pseudo-first order rate equation, the resistance to intraparticle diffusion cannot be neglected. Sorption isotherms were fitted by Langmuir equation (maximum sorption capacities: 1-1.2 mmol g^-1). Thermodynamics are also investigated showing differences between the two types of functionalized groups: exothermic for TUR/SiO₂ and endothermic for UR/SiO₂. Metal desorption is highly effective using 0.3-0.5 M HCl solutions: total desorption occurs within 30-60 min; sorption/desorption properties are remarkably stable for at least 5 cycles. The sorbents have marked preference for U(VI) and Th(IV) over alkali-earth and base metals at pH_eq ~4.8. By preliminary precipitation steps, it is possible "cleaning" ore leachates of pegmatite ore, and recovering U(VI) and Th(IV) using functionalized silica beads. After elution and selective recovery by precipitation with oxalate (Th-cake) and alkaline (U-cake), the metals can be valorized.

Enhanced PAHs-contaminated site soils remediation by mixed persulfate and calcium peroxide

Polycyclic aromatic hydrocarbons (PAHs) remain in the site soils after relocated coking plants and oil refineries pose huge constraints to the subsequent land utilization. However, single persulfate (PS) or calcium peroxide (CP) remediation strategies can only inefficiently oxidize some PAHs in soil. This work sought to optimize PS/CP oxidation remediation strategy and verify its practical application effect in soil samples spiked with PAHs. The results showed that the mixed PS/CP oxidation remediation was better than the single oxidants strategies; it had high remediation performance in different particles and pollution loads of PAHs-contaminated soils. Simultaneously, reactive radicals (SO₄·^- and ·OH) were detected, and one side-product (CaSO₄) was characterized. This work optimized the mixed PS/CP system (0.3 mol/L PS, and 8 g/kg CP, together with 0.18 mol/L Fe²⁺ and 0.11 mol/L C₂O₄^2-), and the corresponding Total-PAHs removal rate was 85.41%. Compared to the cost based on benzopyrene (BaP) removal, the study provided a cost-effective mixed PS/CP oxidation remediation technique (1.22 $/ton), widely applicable in soils polluted with various organic contaminants represented such as PAHs.

Waste feather fiber based high extraction capacity bio-adsorbent for sustainable uranium extraction from seawater

Recycling uranium from seawater is of great significance to the development of nuclear industry. However, due to high salinity and low uranium concentration in seawater, there are still many challenges in current seawater uranium extraction technology. In this study, waste feather fibers (FF) were used as raw materials to develop a phosphonate-functionalized feather fiber (FF-PT). The study on the adsorption performance shows that FF-PT have good adsorption and recycling performance for uranium. The study on the adsorption performance shows that FF-PT have good adsorption and recycling performance for uranium. The adsorption capacity reaches up to 342.5 mg·g^-1 in the 8 ppm uranium solution, and service life of at least 10 cycles were obtained. In addition, in the environment with high salinity and the coexistence of metal competitive ions, FF-PT also shows excellent selectivity, and it can reach 3.22 mg·g^-1 adsorption capacity after immersed in natural seawater for 30 days. Combined with the results of economic analysis, we believe that the FF-PT has broad application prospects in the industrialized uranium extraction from seawater.

Decorating UiO-66-NH2 crystals on recyclable fiber bearing polyamine and amidoxime bifunctional groups via cross-linking method with good stability for highly efficient capture of U(VI) from aqueous solution

Although polyacrylonitrile fiber (PANF) and metal-organic frameworks (MOFs) have been extensively investigated to remove U(VI) from water, their practical applications are seriously hindered by the relatively low stability of PANF in acidic solution and great difficulty of separating MOFs nanoparticles from solution, beside that, little attention is paid to the fabrication of MOFs and PANF composite materials (MPCMs) with excellent adsorption capacity for U(VI). Herein, we report the synthesis of novel MPCMs by decorating different concentrations of UiO-66-NH2 crystals onto polyamine and amidoxime groups functionalized PANF (PA-AO-PANF) through cross-linking method for U(VI) extraction. The characterization results reveal that the combination of PA-AO-PANF and UiO-66-NH2 crystals endows MPCMs with excellent separation ability, large surface area, good stability and plentiful surface functional groups, which contributes to good selectivity and enhanced adsorption performance. Consequently, the obtained UN-PA-AO-PANF-2 shows the maximum uptake capacity of 441.8 mg/g and equilibrium uptake time of 30 min towards U(VI). Besides, the U(VI) uptake ability and structure of UN-PA-AO-PANF-2 are well preserved after ten adsorption-desorption cycles. With these outstanding properties, the adsorbent has great potential for the capture of U(VI) from aqueous solutions. Importantly, this work provides a cost-effective and efficient way to construct extremely stable MPCMs hybrid fibers.

Efficient removal of uranium from wastewater using pig manure biochar: Understanding adsorption and binding mechanisms

In this work, three kinds of biochars (PMBC-H₂O, PMBC-PP and PMBC-HP) with excellent adsorption performance were obtained by carbonizing pig manure pre-treated with different agents. These biochars had the ordered mesoporous structures and possessed abundant active functional groups on their surface. The adsorption behaviors of the biochars towards U_VI under various conditions were evaluated by batch experiment. The results showed that KMnO₄ and H₂O₂ could enormously improve the adsorption performance of PMBC to U_VI. After KMnO₄ and H₂O₂ pretreatment, the maximum adsorption capacities of PMBC-PP (979.3 mg/g) and PMBC-HP (661.7 mg/g) were about 2.6 and 1.8 times higher than that of PMBC-H₂O (369.9 mg/g), respectively, which was much higher than previously reported biochar-based materials. Obviously, KMnO₄ pretreatment leaded to a higher enhancement than that of H₂O₂. The removal mechanism of U_VI on PMBC-PP was discussed in-depth. The interaction between U_VI species and PMBC-PP was mainly ascribed to the abundant active sites on the surface of PMBC-PP. In a word, conversion of pig manure pre-treated with KMnO₄ into biochar not only demonstrates that PMBC-PP has great potential in the treatment of actual uranium-containing wastewater, but also provides a method for the rational utilization of pig manure to reduce the pollution.

A Novel Combined Treatment Process of Hybrid Biosorbent–Nanofiltration for Effective Pb(II) Removal from Wastewater

The untreated effluents discharged by different industries, such as metallurgy, fertilizers, pesticide, leather, mining, electroplating, surface finishing, aerospace, and electroplating, have increased the risk of the contamination of bodies of water by heavy metals. Herein, hybrid biosorbent–nanofiltration processes for Pb(II) removal from wastewater was studied. The hybrid biosorbent was prepared from date seed waste and Ganoderma lucidum. Hybrid biosorbent characterization was performed by SEM and FTIR. SEM micrographs showed that the HB surface is irregular. For the adsorption studies, various sorption parameters were optimized. The maximum biosorption capacity of immobilized heat-inactivated hybrid biosorbent was 365.9 mg/g, with the Langmuir isotherm model to present the best fit. Desorption experiments were conducted for regenerating immobilized heat-inactivated hybrid biosorbent for three consecutive cycles using different desorption agents, with acetic acid to be the optimum. Going a step further, nanofiltration was also applied as a post-treatment process to elevate the remediation effectiveness for wastewater of high Pb(II) initial concentrations. The reasonably low cost and high removal of Pb(II) make hybrid biosorbent–nanofiltration processes a prosperous and potentially attractive hybrid approach against heavy-metal-polluted wastewater.

The Adsorption Characteristics of Uranium(VI) from Aqueous Solution on Leonardite and Leonardite-Derived Humic Acid: A Comparative Study

The humic substance is a low-cost and effective adsorbent with abundant functional groups in remediating uranium (U) (VI)-contaminated water. In this research study, leonardite together with leonardite-derived humic acid (L-HA) was used to eliminate U(VI) from water under diverse temperatures (298, 308, and 318 K). L-HA showed a higher adsorption volume for U(VI) than leonardite. U adsorption was varied with pH and increased with temperature. The adsorption kinetics of L-HA had a higher determination coefficient (R²) for pseudo-second-order (R² > 0.993) and Elovich (R² > 0.987) models, indicating possible chemisorption-assisted adsorption. This was further supported with the activation energies (15.9 and 13.2 kJ/mol for leonardite and L-HA, respectively). Moreover, U(VI) equilibrium adsorption on leonardite was better depicted with the Freundlich model (R² > 0.970), suggesting heterogeneous U(VI) adsorption onto the leonardite surface. However, U(VI) adsorption onto L-HA followed the Langmuir equation (R² > 0.971), which implied the dominant role of monolayer adsorption in controlling the adsorption process. Thermodynamic parameters, including standard entropy change (ΔS⁰ > 0), Gibbs free energy (ΔG⁰ < 0), and standard enthalpy change (ΔH⁰ > 0), suggested a spontaneous and endothermal adsorption process. In addition, ionic species negatively affected U(VI) adsorption by leonardite and L-HA.

Synthesis of a New Phosphonate-Based Sorbent and Characterization of Its Interactions with Lanthanum (III) and Terbium (III)

High-tech applications require increasing amounts of rare earth elements (REE). Their recovery from low-grade minerals and their recycling from secondary sources (as waste materials) are of critical importance. There is increasing attention paid to the development of new sorbents for REE recovery from dilute solutions. A new generation of composite sorbents based on brown algal biomass (alginate) and polyethylenimine (PEI) was recently developed (ALPEI hydrogel beads). The phosphorylation of the beads strongly improves the affinity of the sorbents for REEs (such as La and Tb): by 4.5 to 6.9 times compared with raw beads. The synthesis procedure (epicholorhydrin-activation, phosphorylation and de-esterification) is investigated by XPS and FTIR for characterizing the grafting route but also for interpreting the binding mechanism (contribution of N-bearing from PEI, O-bearing from alginate and P-bearing groups). Metal ions can be readily eluted using an acidic calcium chloride solution, which regenerates the sorbent: the FTIR spectra are hardly changed after five successive cycles of sorption and desorption. The materials are also characterized by elemental, textural and thermogravimetric analyses. The phosphorylation of ALPEI beads by this new method opens promising perspectives for the recovery of these strategic metals from mild acid solutions (i.e., pH ~ 4).