Catalytic ozonation of VOCs at low temperature: A comprehensive review

High-efficient M-NC single-atom catalysts for catalytic ozonation in water purification: Performance and mechanisms

Heterogeneous catalytic ozonation (HCO) holds promise in water purification but suffers from limited accessible metal sites, metal leaching, and unclear structure-activity relationships. This work reported M-NC (M=Co, Ni, Fe, and Mn) single-atom catalysts (SACs) with high atomic efficiency and minimal metal release. The new HCO systems, especially the Co-based system, exhibited impressive performance in various refractory contaminant removal, involving various reactive species generation, such as •OHads, •OHfree, *O, and 1O2. For sulfamethoxazole removal, the normalized kobs for Co-NC, Ni-NC, Fe-NC, and Mn-NC were determined as 13.53, 3.94, 3.55, and 4.13 min-1·mMmetal-1·g·m-2 correspondingly, attributed to the abundant acid sites, faster electron transfer, and lower energy required for O3 decomposition and conversion. The metal atoms and hydroxyl groups, individually serving as Lewis and Bronsted acid sites (LAS and BAS), were the primary centers for •OH generation and O3 adsorption. The relationships between active sites and both O3 utilization and •OH generation were found. LAS and BAS were responsible for O3 adsorption, while strong LAS facilitated O3 conversion into •OH. Theoretical calculations revealed the catalytic mechanisms involved O3→ *O→ *OO→ O3•-→ •OH. This work highlights the significance of SAC design for HCO and advances the understanding of atomic-level HCO behavior.

Enhancement of light-driven adsorption efficacy through the integration of NiCo2O4 onto CeO2 for photo-ozone catalytic degradation of toluene

In this study, a co-catalytic route was explored to enhance the photo-ozone catalytic degradation of volatile organic compounds (VOCs). NiCo2O4 was loaded onto the surface of CeO2 nanoparticles to create a composite catalyst (10%NiCo2O4/CeO2). The integration of NiCo2O4 onto CeO2 enhanced the interaction between the catalyst and toluene, a representative VOC, resulting in significantly increased toluene adsorption without a corresponding increase in specific surface area. This integration also improved the utilization of charge carriers and conversion of ozone to O2-. Under visible light irradiation, H2O accumulated charge carriers at 10%NiCo2O4/CeO2's surface, facilitating both ozone utilization and toluene adsorption. Another benefit of NiCo2O4 loading was its ability to enhance the conversion efficiency of solar energy. Consequently, the toluene removal and mineralization efficiencies of 10%NiCo2O4/CeO2 were enhanced by 182% and 309% compared to CeO2, and by 201% and 357% compared to NiCo2O4, respectively. Overall, this study demonstrated a novel co-catalyst design strategy for enhancing the photo-ozone catalytic degradation of VOCs.

Enhancement of Gaseous o-Xylene Elimination by Chlorosulfonic Acid-Modified H-Zeolite Socony Mobil-5

It is important to develop effective strategies for enhancing the removal capacity of aromatic volatile organic compounds (VOCs) by modifying conventional porous adsorbents. In this study, a novel HZSM-5 zeolite-supported sulfonic acid (ZSM-OSO3H) was prepared through ClSO3H modification in dichloromethane and employed for the elimination of gaseous o-xylene. The ClSO3H modification enables the bonding of -OSO3H groups onto the HZSM-5 support, achieving a loading of 8.25 mmol·g-1 and leading to a degradation in both crystallinity and textural structure. Within an active temperature range of 110-145 °C, ZSM-OSO3H can efficiently remove o-xylene through a novel reactive adsorption mechanism, exhibiting a removal rate exceeding 98% and reaching a maximum breakthrough adsorption capacity of 264.7 mg. The adsorbed o-xylene derivative is identified as 3,4-dimethylbenzenesulfonic acid. ZSM-OSO3H demonstrates superior adsorption performance for o-xylene along with excellent recyclability. These findings suggest that ClSO3H sulfonation offers a promising approach for modifying various types of zeolites to enhance both the elimination and resource conversion of aromatic VOCs.

The Surface/Interface Modulation of Platinum Group Metal (PGM)-Free Catalysts for VOCs and CO Catalytic Oxidation

Effective management of volatile organic compounds (VOCs) and carbon monoxide (CO) is critical to human health and the ecological environment. Catalytic oxidation is one of the most promising technologies for achieving efficient VOCs and CO emission control. Platinum group metal (PGM)-free catalysts are recently receiving sustainable attention in catalyzing VOCs and CO removal due to their low cost, superior catalytic activity, and excellent stability, but PGM-free catalysts face challenges in low-temperature catalytic efficiency. In this mini-review, starting with discussing the catalytic mechanism of VOCs and CO oxidation, we summarize the surface/interface modulation strategies of PGM-free catalysts to promote oxygen and VOCs/CO molecule activation for enhanced low-temperature oxidation activity, including oxygen vacancy engineering, heteroatom doping, surface acidity modification, and active interface construction. We highlight the currently remaining challenges and prospects of advanced PGM-free catalyst development for highly efficient VOCs and CO emission control in practical applications.

Fundamental insights and recent advances in catalytic oxidation processes using ozone for the control of volatile organic compounds

The development of technologies for highly efficient treatment of emissions containing low concentrations of volatile organic compounds (VOCs) remains an important challenge. Catalytic oxidation with ozone (catalytic ozonation) is useful for the oxidative decomposition of VOCs, particularly aromatic compounds, under ambient temperature conditions. Only inexpensive transition metal oxides are required as catalysts, and Mn-based catalysts are widely used for catalytic ozonation. This review describes the oxidation reaction mechanisms, reaction pathways of aromatic hydrocarbons, and dependence of the catalytic ozonation activity on the reaction conditions. The reasons why Mn oxides are effective in catalytic ozonation are also explained. The structure of the catalytic active sites and the types of supporting materials contributing to the reaction are also discussed in detail, with the aim of establishing a VOC control technology. In addition, recent progress in catalytic oxidation processes using ozone as an oxidant has been outlined, focusing on catalyst materials and reaction conditions.

A comprehensive review and perspective research in technology integration for the treatment of gaseous volatile organic compounds

Volatile organic compounds (VOCs) are harmful pollutants emitted from industrial processes. They pose a risk to human health and ecosystems, even at low concentrations. Controlling VOCs is crucial for good air quality. This review aims to provide a comprehensive understanding of the various methods used for controlling VOC abatement. The advancement of mono-functional treatment techniques, including recovery such as absorption, adsorption, condensation, and membrane separation, and destruction-based methods such as natural degradation methods, advanced oxidation processes, and reduction methods were discussed. Among these methods, advanced oxidation processes are considered the most effective for removing toxic VOCs, despite some drawbacks such as costly chemicals, rigorous reaction conditions, and the formation of secondary chemicals. Standalone technologies are generally not sufficient and do not perform satisfactorily for the removal of hazardous air pollutants due to the generation of innocuous end products. However, every integration technique complements superiority and overcomes the challenges of standalone technologies. For instance, by using catalytic oxidation, catalytic ozonation, non-thermal plasma, and photocatalysis pretreatments, the amount of bioaerosols released from the bioreactor can be significantly reduced, leading to effective conversion rates for non-polar compounds, and opening new perspectives towards promising techniques with countless benefits. Interestingly, the three-stage processes have shown efficient decomposition performance for polar VOCs, excellent recoverability for nonpolar VOCs, and promising potential applications in atmospheric purification. Furthermore, the review also reports on the evolution of mathematical and artificial neural network modeling for VOC removal performance. The article critically analyzes the synergistic effects and advantages of integration. The authors hope that this article will be helpful in deciding on the appropriate strategy for controlling interested VOCs.

Supported nano-sized precious metal catalysts for oxidation of catalytic volatile organic compounds

Volatile organic compounds (VOCs) are common contaminants found as indoor as well as outdoor pollutants, which can induce acute or chronic health hazards to the human physiological system. The catalytic oxidation method is widely considered as one of the effective methods for removing VOCs, and the development of highly effective catalysts is highly urgent for booming this interesting field. This review focuses on the recent progress of VOC oxidation catalyzed by supported nano-sized precious metal catalysts, and discusses the effects of metal composition, supports, size, and morphology on the catalytic activity. In addition, the roles played by both nano-sized precious metals and supports in enhancing the performance of catalytic VOCs are also systematically discussed, which will guide the further development of more advanced VOC catalysts.

Spatiotemporal changes in fine particulate matter and ozone in the oasis city of Korla, northeastern Tarim Basin of China

Air pollution is a serious environmental health concern for humans and other living organisms. This study analyzes the spatial and temporal characteristics of air pollutant concentrations, changes in the degree of pollution, and the wavelet coherence of the air quality index (AQI) with pollutants in various monitoring stations. The analysis is based on long-term time series data (January 2016 to December 2023) of air pollutants (PM2.5, PM10, and O3) from Korla, an oasis city in the northeastern part of the Tarim Basin, China. The concentrations of PM2.5, PM10, and O3 in Korla showed a cyclical trend from 2016 to 2023; PM10 concentrations exhibited all-season exceedance and PM2.5 exhibited exceedance only in spring. PM2.5 and PM10 showed a seasonal distribution of spring > winter > fall > summer; O3 concentrations showed a seasonal distribution of summer > spring > fall > winter. Strong positive wavelet coherence between PM and Air Quality Index (AQI) data series suggests that the AQI data series can effectively characterize fluctuating trends in PM concentrations. Moreover, PM10 levels IV and VI were maintained at approximately 10%, indicating that sand and dust have a substantial influence on air quality and pose potential threats to the health of urban inhabitants. Based on the results of this study, future efforts must strengthen relative countermeasures for sand prevention and control, select urban greening species with anti-pollution capabilities, rationally expand urban green spaces, and restrict regulations for reducing particulate matter emissions within city areas.

Enhanced Replenishment of Active Lattice Oxygen Using Chiral Copper Oxide

Effective catalytic performance of the transition metal oxide is attributed to high specific surface areas, abundant surface oxygen atoms, and balanced valence ratios. Although the chirality of the transition metal has attracted attention, most studies have focused on optical application. A few chiral transition metal oxides were used as electrocatalysts and photocatalysts. The influence of the chiral catalysts on the thermal catalysis process has been less explored. In this study, Mn-loaded chiral (M/l-CuO and M/d-CuO) and achiral CuO (M/a-CuO) were synthesized and compared in the catalytic oxidization of toluene. Spectrally analyzed Mn was well-dispersed on both chiral and achiral CuO. l-CuO and d-CuO showed nanoflower-like chirality. The angles between each (001) plane of CuO were the source of chirality. The toluene turnover frequency (TOF) of the samples was in the order of Mn/d-CuO (5.6 × 10-5 s-1) > Mn/l-CuO (4.4 × 10-5 s-1) > Mn/a-CuO (3.2 × 10-5 s-1) at 240 °C, consistent with the order of the oxygen replenishment rate. The as-prepared catalysts had similar ratios of lattice oxygen/surface adsorbed oxygen, Mn3+/Mn4+, and Cu+/Cu2+. A higher TOF was attributed to chirality, which increased the lattice oxygen replenishment speed from the gaseous phase to the solid surface. Our study indicates gas-solid catalysis from a structure-activity viewpoint.

Research on the kinetics and degradation pathways of gaseous acetic acid ester organics

ABSTRACTDesigned to meet the specific needs of the printing industry exhaust gas emissions, this paper proposes a method for the degradation of gaseous acetic acid ester organics that is environmentally friendly, safe, and simple to use: micro-nano cavitation technology. In the process of using micro-nano cavitation technology to degrade acetic acid ester organics, the products in the degradation process were analyzed by gas chromatography-mass (GC-MS) spectrometry, and the degradation pathways of acetic acid ester organics were identified. Under high temperatures and high pressure caused by cavitation collapse, the C-C bond and C-O bond on the main chain of organic matter are cleaved to form low molecular products. Low-molecular intermediate products are continuously produced as the reaction advances, and these intermediate products are further oxidized and decomposed into carbon dioxide and water. Besides, the factors that influence the degradation rate of acetic acid ester organics were investigated. Based on the experimental data, acetic acid esters can degrade with the greatest efficiency when their initial concentration is 200 ± 50 mg/m3 and their treatment time is 20∼30 min. Moreover, the experiment was optimized using the response surface method. The results suggested that for an initial concentration of 155.544 mg/m3 and a reaction time of 21.961 min, the best degradation rate was 0.251 min-1. Micro-nano cavitation technology is a novel and promising technology for the degradation of volatile organic compounds, with a wide range of practical applications.

Highly Dispersed Ni Atoms and O3 Promote Room-Temperature Catalytic Oxidation

Transition metal oxides are promising catalysts for catalytic oxidation reactions but are hampered by low room-temperature activities. Such low activities are normally caused by sparse reactive sites and insufficient capacity for molecular oxygen (O2) activation. Here, we present a dual-stimulation strategy to tackle these two issues. Specifically, we import highly dispersed nickel (Ni) atoms onto MnO2 to enrich its oxygen vacancies (reactive sites). Then, we use molecular ozone (O3) with a lower activation energy as an oxidant instead of molecular O2. With such dual stimulations, the constructed O3-Ni/MnO2 catalytic system shows boosted room-temperature activity for toluene oxidation with a toluene conversion of up to 98%, compared with the O3-MnO2 (Ni-free) system with only 50% conversion and the inactive O2-Ni/MnO2 (O3-free) system. This leap realizes efficient room-temperature catalytic oxidation of transition metal oxides, which is constantly pursued but has always been difficult to truly achieve.

Enhancement Effect Induced by the Second Metal to Promote Ozone Catalytic Oxidation of VOCs

It is a promising research direction to develop catalysts with high stability and ozone utilization for low-temperature ozone catalytic oxidation of VOCs. While bimetallic catalysts exhibit excellent catalytic activity compared with conventional single noble metal catalysts, limited success has been achieved in the influence of the bimetallic effect on the stability and ozone utilization of metal catalysts. Herein, it is necessary to systematically study the enhancement effect in the ozone catalytic reaction induced by the second metal. With a simple continuous impregnation method, a platinum-cerium bimetallic catalyst is prepared. Also highlighted are studies from several aspects of the contribution of the second metal (Ce) to the stability and ozone utilization of the catalysts, including the "electronic effect" and "geometric effect". The synergistic removal rate of toluene and ozone is nearly 100% at 30 °C, and it still shows positive stability after high humidity and a long reaction time. More importantly, the instructive significance, which is the in-depth knowledge of enhanced catalytic mechanism of bimetallic catalysts resulting from a second metal, is provided by this work.

Synergistic catalytic removal of NOx and chlorinated organics through the cooperation of different active sites

The synergistic removal of NOx and chlorinated volatile organic compounds (CVOCs) has become the hot topic in the field of environmental catalysis. However, due to the trade-off effects between catalytic reduction of NOx and catalytic oxidation of CVOCs, it is indispensable to achieve well-matched redox property and acidity. Herein, synergistic catalytic removal of NOx and chlorobenzene (CB, as the model of CVOCs) has been originally demonstrated over a Co-doped SmMn2O5 mullite catalyst. Two kinds of Mn-Mn sites existed in Mn-O-Mn-Mn and Co-O-Mn-Mn sites were constructed, which owned gradient redox ability. It has been demonstrated that the cooperation of different active sites can achieve the balanced redox and acidic property of the SmMn2O5 catalyst. It is interesting that the d band center of Mn-Mn sites in two different sites was decreased by the introduction of Co, which inhibited the nitrate species deposition and significantly improved the N2 selectivity. The Co-O-Mn-Mn sites were beneficial to the oxidation of CB and it cooperates with Mn-O-Mn-Mn to promote the synergistic catalytic performance. This work paves the way for synergistic removal of NOx and CVOCs over cooperative active sites in catalysts.

QSAR models for the ozonation of diverse volatile organic compounds at different temperatures

In order to assess the fate and persistence of volatile organic compounds (VOCs) in the atmosphere, it is necessary to determine their oxidation rate constants for their reaction with ozone (kO3). However, given that experimental values of kO3 are only available for a few hundred compounds and their determination is expensive and time-consuming, developing predictive models for kO3 is of great importance. Thus, this study aimed to develop reliable quantitative structure-activity relationship (QSAR) models for 302 values of 149 VOCs across a broad temperature range (178-409 K). The model was constructed based on the combination of a simplified molecular-input line-entry system (SMILES) and temperature as an experimental condition, namely quasi-SMILES. In this study, temperature was incorporated in the models as an independent feature. The hybrid optimal descriptor generated from the combination of quasi-SMILES and HFG (hydrogen-filled graph) was used to develop reliable, accurate, and predictive QSAR models employing the CORAL software. The balance between the correlation method and four different target functions (target function without considering IIC or CII, target function using each IIC or CII, and target function based on the combination of IIC and CII) was used to improve the predictability of the QSAR models. The performance of the developed models based on different target functions was compared. The correlation intensity index (CII) significantly enhanced the predictability of the model. The best model was selected based on the numerical value of Rm2 of the calibration set (split #1, Rtrain2 = 0.9834, Rcalibration2 = 0.9276, Rvalidation2 = 0.9136, and calibration = 0.8770). The promoters of increase/decrease for log kO3 were also computed based on the best model. The presence of a double bond (BOND10000000 and $10 000 000 000), absence of halogen (HALO00000000), and the nearest neighbor codes for carbon equal to 321 (NNC-C⋯321) are some significant promoters of endpoint increase.

Surface Hydroxyl and Oxygen Vacancies Engineering in ZnSnAl LDH: Synergistic Promotion of Photocatalytic Oxidation of Aromatic VOCs

Photocatalytic oxidation has gained great interest in environmental remediation, but it is still limited by its low efficiency and catalytic deactivation in the degradation of aromatic VOCs. In this study, we concurrently regulated the surface hydroxyl and oxygen vacancies by introducing Al into ZnSn layered double hydroxide (LDH). The presence of distorted Al species induced local charge redistribution, leading to the remarkable formation of oxygen vacancies. These oxygen vacancies subsequently increased the amount of surface hydroxyl and elongated its bond length. The synergistic effects of surface hydroxyl and oxygen vacancies greatly enhanced reactant adsorption-activation and facilitated charge transfer to generate •OH, •O2-, and 1O2, resulting in highly efficient oxidation and ring-opening of various aromatic VOCs. Compared with commercial TiO2, the optimized ZnSnAl-50 catalyst exhibited about 2-fold activity for the toluene and styrene degradation and 10-fold activity for the chlorobenzene degradation. Moreover, ZnSnAl-50 demonstrated exceptional stability in the photocatalytic oxidation of toluene under a wide humidity range of 0-75%. This work marvelously improves the photocatalytic efficiency, stability, and adaptability through a novel strategy of surface hydroxyl and oxygen vacancies engineering.

The relative dominance of surface oxygen content over pore properties in controlling adsorption and retrograde behavior of gaseous toluene over microporous carbon

The adsorption potential of activated carbon (AC) derived from macadamia nut shells (product code of Procarb-900: namely, AC-P) has been investigated using gaseous toluene as the target pollutant. The powder AC-P with high-microporosity (96%) and oxygen content (5.62%) exhibited very high adsorption capacity (214 mg·g-1) and partition coefficient (PC: 25 mol·kg-1·Pa-1) against 100 ppm (10 Pa) toluene at 99% breakthrough levels (1 atm dry N2). The factors governing toluene adsorption were explored with respect to the key variables such as surface functional groups, pore size distribution, sorbent bed mass (50, 100, and 150 mg), and particle size (i.e., 0.212-0.6 mm (powder AC: PAC)) vs. 0.6-2.36 mm (granular AC: GAC)). Accordingly, the adsorption process was physical, mainly due to the non-polar interactions (i.e., π-π interactions) between the adsorbent and adsorbate molecules. The high affinity of AC-P at low breakthrough levels was obtained through a combination of smaller particle size (PAC) and larger adsorbent mass (i.e., 150 mg) with the appearance of a very pronounced retrograde phenomenon (e.g., at < 1% breakthrough level). As such, toluene adsorption appeared to be affected more sensitively by particle size and adsorbent mass (especially at low breakthrough levels) than by high microporosity. Most importantly, the oxygen content of AC emerges as one of the key factors governing the maximum capacity, as the changes in pore volume are not crucial to explain the observed adsorption patterns of toluene.

Rational prediction of immunogenicity clustering through cross-reactivity analysis of thirteen SARS-CoV-2 variants

SARS-CoV-2 breakthrough infections in vaccinated individuals underscore the threat posed by continuous mutating variants, such as Omicron, to vaccine-induced immunity. This necessitates the search for broad-spectrum immunogens capable of countering infections from such variants. This study evaluates the immunogenicity relationship among SARS-CoV-2 variants, from D614G to XBB, through Guinea pig vaccination, covering D614G, Alpha, Beta, Gamma, Delta, BA.1, BA.2, BA.2.75, BA.2.75.2, BA.5, BF.7, BQ.1.1, and XBB, employing three immunization strategies: three-dose monovalent immunogens, three-dose bivalent immunogens, and a two-dose vaccination with D614G followed by a booster immunization with a variant strain immunogen. Three distinct immunogenicity clusters were identified: D614G, Alpha, Beta, Gamma, and Delta as cluster 1, BA.1, BA.2, and BA.2.75 as cluster 2, BA.2.75.2, BA.5, BF.7, BQ.1.1, and XBB as cluster 3. Broad-spectrum protection could be achieved through a combined immunization strategy using bivalent immunogens or D614G and XBB, or two initial D614G vaccinations followed by two XBB boosters. A comparison of neutralizing antibody levels induced by XBB boosting and equivalent dosing of D614G and XBB revealed that the XBB booster produced higher antibody levels. The study suggests that vaccine antigen selection should focus on the antigenic alterations among variants, eliminating the need for updating vaccine components for each variant.

Engineering the Crystal Facet of Monoclinic NiO for Efficient Catalytic Ozonation of Toluene

Modulating oxygen vacancies of catalysts through crystal facet engineering is an innovative strategy for boosting the activity for ozonation of catalytic volatile organic compounds (VOCs). In this work, three kinds of facet-engineered monoclinic NiO catalysts were successfully prepared and utilized for catalytic toluene ozonation (CTO). Density functional theory calculations revealed that Ni vacancies were more likely to form preferentially than O vacancies on the (110), (100), and (111) facets of monoclinic NiO due to the stronger Ni-vacancy formation ability, further affecting O-vacancy formation. Extensive characterizations demonstrated that Ni vacancies significantly promoted the formation of O vacancies and thus reactive oxygen species in the (111) facet of monoclinic NiO, among the three facets. The performance evaluation showed that the monoclinic NiO catalyst with a dominant (111) facet exhibits excellent performance for CTO, achieving a toluene conversion of ∼100% at 30 °C after reaction for 120 min under 30 ppm toluene, 210 ppm ozone, 45% relative humidity, and a space velocity of 120 000 h-1. This outperformed the previously reported noble/non-noble metal oxide catalysts used for CTO at room temperature. This study provided novel insight into the development of highly efficient facet-engineered catalysts for the elimination of catalytic VOCs.

Regulating oxygen vacancies and hydroxyl groups of α-MnO2 nanorods for enhancing post-plasma catalytic removal of toluene

Although nonthermal plasma (NTP) technology has high removal efficiency for volatile organic compounds (VOCs), it has limited carbon dioxide (CO2) selectivity, which hinders its practical application. In this study, α-MnO2 nanorods with tunable oxygen vacancies and hydroxyl groups were synthesized by two-step hydrothermal process to enhance their activity for deep oxidation of toluene. Hydrochloric acid (HCl) was used to assist in synthesis of α-MnO2 nanorods with tunable oxygen vacancies, furtherly, more hydroxyl groups were introduced to HCl-assisted synthesized α-MnO2 by K+ supplement. The results showed that the as-synthesized nanorods exhibited superior activity, improved by nearly 30% removal efficiency of toluene compared to pristine MnO2 at SIE = 339 J/L, and reaching high COx selectivity of 72% at SIE = 483 J/L, successfully promoting the deep oxidation of toluene. It was affirmed that oxygen vacancies played an important role in toluene conversion, improving the conversion of ozone (O3) and resulting in higher mobility of surface lattice oxygen species. Besides, the enhancement of deep oxidation performance was caused by the increase of hydroxyl groups concentration. In-situ DRIFTS experiments revealed that the adsorbed toluene on catalyst surface was oxidized to benzyl alcohol by surface lattice oxygen, and hydroxyl groups were also found participating in toluene adsorption. Overall, this study provides a new approach to designing catalysts for deep oxidation of VOCs.

Preparation of a Novel Straw-Sludge Activated Biochar and Its Adsorption Mechanisms for Removal of VOCs

To simultaneously achieve the objectives of waste resource utilization and clean production, a novel approach involving the utilization of corn straw-sludge hybrid biochar was proposed for the adsorption of VOCs emitted from biomass power plants. This study analyzed the effect of straw-sludge biochar on the adsorption characteristics of VOCs (toluene, isopentane, and ethylene) under different preparation conditions (raw material ratio, activation temperature, and activation time). The findings revealed that the adsorption efficiency of the mixed biochar was significantly superior to that of individual corn straw biochar and sludge biochar. The adsorption of methylbenzene, isopentane, and ethylene was 78.32, 40.81, and 41.18% higher, respectively, compared to the control groups consisting of pure sludge biochar and pure corn straw biochar. Moreover, the adsorption performance of the activated biochar followed the sequence of ethylene < isopentane < methylbenzene in terms of both saturation time and adsorption capacity. The adsorption capacity of VOCs on straw biochar-sludge biochar demonstrated a consistent correlation with the boiling point and molecular weight of the adsorbate, with higher adsorption capacities observed for adsorbates with larger boiling points and molecular weights, specifically methylbenzene > isopentane > ethylene.

Deep mineralization of VOCs in an embedded hybrid structure CoFe2O4/MoS2/PMS wet scrubber system

Peroxymonosulfate (PMS)-based advanced oxidation processes in liquid phase systems can actively degrade toluene. In this work, the catechol structural surfactant was introduced to synthesize the dispersed and homogeneous CoFe2O4 nanospheres and embedded into MoS2 nanoflowers to form magnetically separable heterojunction catalysts. The innovative approach effectively mitigated the traditionally low reduction efficiency of transition metal ions during the heterogeneous activation process. In CoFe2O4/MoS2/PMS system, the toluene removal efficiency remained 95% within 2 h. The contribution of SO4⋅-, ·O2-, ·OH, and 1O2 was revealed by radical quenching experiment and electron paramagnetic resonance spectroscopy. The results illustrated that MoS2 offers ample reduction sites for facilitating PMS activation via Fe3+/Fe2+ redox interactions. Furthermore, an investigation into the toluene degradation pathway within the CoFe2O4/MoS2/PMS system revealed its capability to suppress the formation of toxic byproducts. This ambient-temperature liquid-phase method presented promising route for the removal of industrial volatile organic pollutants.

Recent advances in the control of volatile organic compounds emissions from indoor wood-based panels: A comprehensive review

Wood-based panels provide efficient alternatives to materials such as plastics derived from traditional petroleum sources and thereby help to mitigate greenhouse gas emissions. Unfortunately, using indoor manufactured panel products also results in significant emissions of volatile organic compounds including olefins, aromatic and ester compounds, which negatively affect human health. This paper highlights recent developments and notable achievements in the field of indoor hazardous air treatment technologies to guide future research toward environmentally friendly and economically feasible directions that may have a significant impact on the improvement of human settlements. Summarizing and synthesizing the principles, advantages, and limitations of different technologies can assist policymakers and engineers in identifying the most appropriate technology for a particular air pollution control program based on criteria such as cost-effectiveness, efficiency, and environmental impact. In addition, insights into the development of indoor air pollution control technologies are provided and potential areas for innovation, improvement of existing technologies, and development of new technologies are identified. Finally, the authors also hope that this sub-paper will raise public awareness of indoor air pollution issues and promote a better understanding of the importance of indoor air pollution control technologies for public health, environmental protection, and sustainable development.

Crystal Plane Effect of Co3O4 on Styrene Catalytic Oxidation: Insights into the Role of Co3+ and Oxygen Mobility at Diverse Temperatures

In the oxidation reaction of volatile organic compounds catalyzed by metal oxides, distinguishing the role of active metal sites and oxygen mobility at specific preferentially exposed crystal planes and diverse temperatures is challenging. Herein, Co₃O₄ catalysts with four different preferentially exposed crystal planes [(220), (222), (311), and (422)] and oxygen vacancy formation energies were synthesized and evaluated in styrene complete oxidation. It is demonstrated that the Co₃O₄ sheet (Co₃O₄-I) presents the highest C₈H₈ catalytic oxidation activity (R_250 °C = 8.26 μmol g^-1 s^-1 and WHSV = 120,000 mL h^-1 g^-1). Density functional theory studies reveal that it is difficult for the (311) and (222) crystal planes to form oxygen vacancies, but the (222) crystal plane is the most favorable for C₈H₈ adsorption regardless of the presence of oxygen vacancies. The combined analysis of temperature-programmed desorption and temperature-programmed surface reaction of C₈H₈ proves that Co₃O₄-I possesses the best C₈H₈ oxidation ability. It is proposed that specific surface area is vital at low temperature (below 250 °C) because it is related to the amount of surface-adsorbed oxygen species and low-temperature reducibility, while the ratio of surface Co³⁺/Co²⁺ plays a decisive role at higher temperature because of facile lattice oxygen mobility. In situ diffuse reflectance infrared Fourier spectroscopy and the ¹⁸O₂ isotope experiment demonstrate that C₈H₈ oxidation over Co₃O₄-I, Co₃O₄-S, Co₃O₄-C, and Co₃O₄-F is mainly dominated by the Mars-van Krevelen mechanism. Furthermore, Co₃O₄-I shows superior thermal stability (57 h) and water resistance (1, 3, and 5 vol % H₂O), which has the potential to be conducted in the actual industrial application.

Catalytic ozonation of methylethylketone over porous Mn-Cu/HZSM-5

The catalytic ozonation of methylethylketone (MEK) was performed at the room temperature (25 °C) using the synthesized Mn and Cu-loaded zeolite (ZSM-5, SiO₂/Al₂O₃ = 80) catalysts. The ZSM-5 zeolite was used as a porous support material due to the large surface area and high capacity for adsorption of volatile organic compounds. Since Mn and Cu-loaded zeolite catalysts were effective for the catalytic ozonation of VOCs such as MEK, according to the loaded concentration of Mn and Cu, there are four types of metal loaded ZSM5 catalysts synthesized [5 wt% Mn/ZSM-5, 5 wt% Cu/ZSM-5, 5 wt% Mn-1 wt% Cu/ZSM-5 (5Mn1CuZSM), and 5 wt% Cu-1 wt% Mn/ZSM-5]. The catalytic efficiency for the removal of MEK and ozonation using the different catalysts was also studied. Based on various experimental analysis processes, the characteristics of the synthesized catalysts were explored and the removal efficiencies of MEK and O₃ together with the CO_x concentration generated from the destruction of MEK and O₃ were explored. The results for the decomposition of MEK and O₃ at the room temperature indicated that the Mn dominant ZSM-5 catalysts showed better efficiency for the conversion of MEK and O₃. The 5 wt% Mn/ZSM-5 outweighed the rest of them for the removal of MEK while the 5Mn1CuZSM showed the best catalytic reactivity for the conversion of O₃ and the CO₂ selectivity. It was ascertained that during the reaction time of catalyst and reactants of 120 min the Mn dominantly deposited bimetallic catalyst, 5Mn1CuZSM, was determined as the most effective for the removal of MEK and O₃ due to the high capability of production of Mn³⁺ species and more available adsorbed oxygen sites compared to the other catalysts. Finally, the durability measurement for the 5Mn1CuZSM catalyst was performed together with the produced CO and CO₂ concentration for 420 min.

Comparison of photocatalysis and photolysis of 2,2,4,4-tetrabromodiphenyl ether (BDE-47): Operational parameters, kinetic studies, and data validation using three modern machine learning models

Polybrominated diphenyl ethers (PBDEs) are halogenated organic compounds that are among the major pollutants of water, and there is an urgent need for their removal. This work compared the application of two techniques, i.e., photocatalytic reaction (PCR) and photolysis (PL), for 2,2,4,4- tetrabromodiphenyl ether (BDE-47) degradation. Although a limited degradation of BDE-47 was observed by photolysis (LED/N₂), photocatalytic oxidation by using TiO₂/LED/N₂ proved to be effective in the degradation of BDE-47. The use of a photocatalyst enhanced the extent of BDE-47 degradation by around 10% at optimum conditions in anaerobic systems. Experimental results were systematically validated through modeling with three new and powerful Machine Learning (ML) approaches, including Gradient Boosted Decision Tree (GBDT), Artificial Neural Network (ANN), and Symbolic Regression (SBR). Four statistical criteria (Coefficient of Determination (R²), Root Mean Square Error (RMSE), Average Relative Error (ARER), and Absolute Error (ABER)) were calculated for model validation. Among the applied models, the developed GBDT was the desirable model for predicting the remaining concentration (Ce) of BDE-47 for both processes. Total Organic Carbon (TOC) and Chemical Oxygen Demand (COD) results confirmed that BDE-47 mineralization required additional time than its degradation in both PCR and PL systems. The kinetic study demonstrated that BDE-47 degradation for both processes followed the pseudo-first-order form of the Langmuir-Hinshelwood (L-H) model. More importantly, the calculated electrical energy consumption of photolysis was shown to be ten percent higher than that for photocatalysis, possibly due to the higher irradiation time required in direct photolysis, which in turn increases electricity consumption. This study is useful in proposing a feasible and promising treatment process for the degradation of BDE-47.

Highly Enhanced Photocatalytic NO Removal and Inhibited Peroxyacetyl Nitrate Formation in Synergistic Acetaldehyde Degradation

The coexistence of NO and CH3CHO in the air is considered to produce secondary peroxyacetyl nitrate (PAN) under sunlight irradiation, threatening the ecological environment and public health. Herein, we provide a simple strategy for the photocatalytic removal of NO and acetaldehyde (CH3CHO) on Sr2Sb2O7. In comparison with the single removal, the nearly complete removal of NO is reached by deep oxidation to NO3- with the assistance of CH3CHO. The underlying mechanism is revealed by GC-MS, in situ DRIFTS, and density functional theory calculations. The intermediates •CH3 from CH3CHO and NO2- from NO tend to bond and further oxidize to CH3ONO2, thus promoting NO removal. CH3NO2 and CH3ONO2 are the key products instead of PAN on Sr2Sb2O7 from the synergistic degradation of NO and CH3CHO. This work brings new insights into reaction pathway regulation for promoting performance and suppressing byproducts during synergistic air pollutant removal.

Catalytic Ozonation of Polluter Benzene from -20 to >50 °C with High Conversion Efficiency and Selectivity on Mullite YMn2O5

Catalytic decomposition of aromatic polluters at room temperature represents a green route for air purification but is currently challenged by the difficulty of generating reactive oxygen species (ROS) on catalysts. Herein, we develop a mullite catalyst YMn₂O₅ (YMO) with dual active sites of Mn³⁺ and Mn⁴⁺ and use ozone to produce a highly reactive O* upon YMO. Such a strong oxidant species on YMO shows complete removal of benzene from -20 to >50 °C with a high CO_x selectivity (>90%) through the generated reactive species O* on the catalyst surface (60 000 mL g^-1 h^-1). Although the accumulation of water and intermediates gradually lowers the reaction rate after 8 h at 25 °C, a simple treatment by ozone purging or drying in the ambient environment regenerates the catalyst. Importantly, when the temperature increases to 50 °C, the catalytic performance remains 100% conversion without any degradation for 30 h. Experiments and theoretical calculations show that such a superior performance stems from the unique coordination environment, which ensures high generation of ROS and adsorption of aromatics. Mullite's catalytic ozonation degradation of total volatile organic compounds (TVOC) is applied in a home-developed air cleaner, resulting in high efficiency of benzene removal. This work provides insights into the design of catalysts to decompose highly stable organic polluters.

TiO2-based catalytic systems for the treatment of airborne aromatic hydrocarbons

Among diverse strategies to manage air quality, catalytic oxidation has been a widely used option to mitigate diverse pollutants such as aromatic volatile organic compounds (VOCs), especially benzene, toluene, and xylene (BTX). For such applications, TiO₂-based catalysts have drawn significant research attention for their prominent photo/thermal catalytic activities and photochemical stability. This review has been organized to elaborate on the recent developments achieved in the thermocatalytic, photocatalytic, and photothermal applications of metal/non-metal doped TiO₂ catalysts towards BTX vapors and their reaction mechanisms. The performance of the reported TiO₂-based catalysts has also been analyzed based on multiple computational metrics such as reaction rate (r), quantum yield (QY), space-time yield, and figure of merit (FOM). At last, the research gap and prospects in the catalytic treatment of BTX are also discussed in association with the feasibility and utility of TiO₂-based catalysts in air purification applications.

Boosting Ozone Catalytic Oxidation of Toluene at Room Temperature by Using Hydroxyl-Mediated MnOx/Al2O3 Catalysts

Ozone catalytic oxidation (OZCO) has gained great interest in environmental remediation while it still faces a big challenge during the deep degradation of refractory volatile organic compounds (VOCs) at room temperature. Hydroxylation of the catalytic surface provides a new strategy for regulating the catalytic activity to boost VOC degradation. Herein, OZCO of toluene at room temperature over hydroxyl-mediated MnO_x/Al₂O₃ catalysts was originally demonstrated. Specifically, a novel hydroxyl-mediated MnO_x/Al₂O₃ catalyst was developed via the in situ AlOOH reconstruction method and used for toluene OZCO. The toluene degradation performance of MnO_x/Al₂O₃ was significantly superior to those of most of the state-of-the-art catalysts, and 100% toluene was removed with an excellent mineralization rate (82.3%) and catalytic stability during OZCO. ESR and in situ DRIFTs results demonstrated that surface hydroxyl groups (HGs) greatly improved the reactive oxygen species generation, thus dramatically accelerating the benzene ring breakage and deep mineralization. Furthermore, HGs provided anchoring sites for uniformly dispersing MnO_x and greatly enhanced toluene adsorption and ozone activation. This work paves a way for deep decomposition of aromatic VOCs at room temperature.

Adsorption-enhanced catalytic oxidation for long-lasting dynamic degradation of organic dyes by porous manganese-based biopolymeric catalyst

Improving the adsorption kinetics of metal-oxide catalysts is critical for the enhancement of catalytic performance in heterogeneous catalytic oxidation reactions. Herein, based on the biopolymer pomelo peels (PP) and metal-oxide catalyst manganese oxide (MnO_x), an adsorption-enhanced catalyst (MnO_x-PP) was constructed for catalytic organic dyes oxidative-degradation. MnO_x-PP shows excellent methylene blue (MB) and total carbon content (TOC) removal efficiency of 99.5 % and 66.31 % respectively, and keeps the long-lasting stable dynamic degradation efficiency during 72 h based on the self-built continuous single-pass MB purification device. The chemical structure similarity and negative-charge polarity sites of the biopolymer PP improve the adsorption kinetics of organic macromolecule MB, and construct the adsorption-enhanced catalytic oxidation microenvironment. Meanwhile, the adsorption-enhanced catalyst MnO_x-PP obtains lower ionization potential and O₂ adsorption energy to promote the continuous generation of active substance (O₂*, OH*) for the further catalytic oxidation of adsorbed MB molecules. This work explored the adsorption-enhanced catalytic oxidation mechanism for the degradation of organic pollutants, and provided a feasible technical idea for designing adsorption-enhanced catalysts for the long-lasting efficient removal of organic dyes.

To promote catalytic ozonation of toluene by tuning Brönsted acid sites via introducing alkali metals into the OMS-2-SO42-/ZSM-5 catalyst

Although free hydroxyl radical (·OH) generated on OMS-2-based catalysts during the catalytic ozonation process have been shown as important reactive oxygen species (ROSs) for toluene degradation, improvement of surface ·OH formation ability remains challenging. Here, Na, K, Rb, and Cs-OMS-2-SO₄^2-/ZSM-5 catalysts were prepared, characterized and evaluated for catalytic ozonation of toluene. Both characterizations and DFT calculations showed that the appropriate alkali metal introduction made the catalyst possess with appropriate crystalline, reducibility, and acidity, which was favorable for catalytic ozonation of toluene. Characterizations also showed that alkali metal introduction resulted in water molecule adsorption on Brönsted acid sites of the catalysts, which made water molecule activation by ozone to form ·OH more easily. The introduction of K⁺ content of ∼ 5.9 wt% yielded K-OMS-2-SO₄^2-/ZSM-5 catalyst with the highest Brönsted acid sites and thus formed the most ·OH among the five prepared catalysts. As a result, the catalyst exhibited excellent toluene conversion and CO_x selectivity for catalytic ozonation of toluene at room temperature and ambient humidity. Furthermore, the catalytic activity of deactivated K-OMS-2-SO₄^2-/ZSM-5 catalyst was recovered after regeneration by a combination of water washing and heat treatment. Finally, a complete mechanism for toluene catalytic ozonation, catalyst deactivation, and regeneration was proposed.

Adsorption Phenomenon of VOCs Released from the Fiber-Reinforced Plastic Production onto Carbonaceous Surface

The manufacturing of fiber-reinforced plastics has been linked to the discharge of volatile organic compounds (VOCs), particularly toluene and benzene, which have been identified as posing substantial risks to human health and the environment. To counteract this issue, activated carbons have been suggested as a means of reducing VOC emissions through adsorption. The objective of this study was to investigate the adsorption characteristics of toluene and benzene onto activated carbons produced from coal (AC) and coconut shells (CAC). The study was carried out in an aqueous medium. The findings revealed that the AC sample with higher surface characteristics exhibited a higher adsorption capacity (toluene: 196.0784 mg g−1 and benzene: 181.8182 mg g−1) in comparison to the CAC sample (toluene: 135.1351 mg g−1 and benzene: 116.2791 mg g−1). The superior adsorption performance of AC on both VOCs can be attributed to its higher surface characteristics. The Langmuir model was found to be more appropriate than the Freundlich model, as indicated by the higher coefficient of determination (R2) value of the Langmuir isotherm (avg. R2 = 0.9669) compared to that of the Freundlich isotherm (avg. R2 = 0.9654), suggesting the use of a monolayer adsorption mechanism. The adsorption kinetics of the samples were analyzed using the pseudo-first-order and pseudo-second-order models, and the former was found to be more fitting, indicating that the rate of adsorption is directly proportional to the concentration difference between the solution and the sample surface. The adsorption process was found to be spontaneous and favorable based on the positive value of ΔG_ads. Furthermore, the adsorption process was endothermic and disordered, as indicated by the positive values of ΔH_ads and ΔS_ads. The regeneration efficiency of all the samples was secured more than 95% upon the fifth cycle.

Revelation of contributing mechanism of reactive oxygen species in photocatalytic ozonation heterocyclization of gaseous hexane isomers

The reactive oxygen species (ROS) involved photocatalytic ozonation of gaseous n-hexane to heterocyclic compounds has been recently reported. However, whether such heterocyclization reaction happens on other alkanes and what is the contributing mechanism of ROS to the heterocyclic compound formation are still unclear. In present study, photocatalytic ozonation of three n-hexane's isomers (i.e. 2-methypentane, 3-methylpentane and 2,3-dimethylbutane) on Cu₂O-CuO/TiO₂-foam ceramic was investigated. Within reaction period, 2-methylpentane and 3-methylpentane not only showed higher average degradation efficiency than 2,3-dimethylbutane, but also separately converted to interfacial heterocyclic compounds of 5,5-dimethyldihydro-2(3H)-furanone and 4,5-dimethyl-4,5-dihydro-2(3H)-furanone. Enough reaction time, optimum experimental atmosphere and shorter light wavelength benefited the formation of heterocyclization products. None of O₃, ¹O₂, electron and hole directly contributed to the heterocyclic compound formation. While ^•O₂^- dominated the production of the heterocyclic compound under the dry reaction atmosphere and ^•OH showed more important role than ^•O₂^- in the heterocyclic compound formation under the moist reaction atmosphere. Theoretical calculation confirmed that ^•OH or ^•O₂^- induced heterocyclization reaction of alkane was exothermic, while the former reaction released 0.47 eV higher energy than the later reaction. The findings provide a comprehensive understanding of contributing roles of ROS in heterocyclization reaction of alkanes, and are helpful for effective elimination of industrial alkanes by advanced oxidation methods.

Gaseous ethylbenzene removal by photocatalytic TiO2 nanoparticles immobilized on glass fiber tissue under real conditions: evaluation of reactive oxygen species contribution to the photocatalytic process

Photocatalytic oxidation (PCO) using a TiO₂ catalyst is an effective technique to remove gaseous volatile organic compounds (VOCs). Herein, a lab-scale continuous reactor is used to investigate the photocatalytic performance toward ethylbenzene (EB) vapor removal over TiO₂ nanoparticles immobilized on glass fiber tissue. The role of the reactive species in the removal of EB and the degradation pathway were studied. Firstly, the effect of key operating parameters such as EB concentration (13, 26, 60 mg/m³), relative humidity levels (From 5 to 80%), gas carrier composition (dry air + EB, O₂ + EB and N₂ + EB) and ultraviolet (UV) radiation wavelength (UV-A _365 nm, UV-C _254 nm) were explored. Then, using superoxide dismutase and tert-butanol as trapping agents, the real contribution of superoxide radical anion (O₂^.-) and hydroxyl radicals (OH^.) to EB removal was quantified. The results show that (i) small water vapor content enhances the EB degradation; (ii) the reaction atmosphere plays an important role in the photocatalytic process; and (iii) oxygen atmosphere/UV-C radiation shows the highest EB degradation percentage. The use of radical scavengers confirms the major contribution of the hydroxyl radical to the photocatalytic mechanism with 75% versus 25% for superoxide radical anion.

Effective Toluene Ozonation over δ-MnO2: Oxygen Vacancy-Induced Reactive Oxygen Species

To improve the reactivity and lifetime of catalysts in the catalytic ozonation of toluene, a simple strategy was provided to regulate the morphology and microstructure of δ-MnO₂ via the hydrothermal reaction temperature. The effects of the reaction temperature and the ozone to toluene concentration ratio on the catalyst performance were investigated. The optimized MnO₂-260 catalyst prepared at the limiting hydrothermal temperature (260 °C) showed high catalytic activity (X_Tol = 95%) and excellent stability (1200 min) at the approximately ambient temperature of 40 °C, which was superior to the results in previous studies. The structure and morphology of δ-MnO₂ were characterized by extended X-ray absorption fine structure, X-ray diffraction, scanning electron microscopy, positron annihilation lifetime spectroscopy, electron spin resonance, and other techniques. Experimental results and density functional theory calculations were in agreement that surface oxygen vacancy clusters, especially surface oxygen dimer vacancies, are critical in ozone activation. Oxygen vacancies can facilitate the adsorption and activation of O₃ to generate reactive oxygen species (ROS, including ¹O₂, O₂^-, and ^•OH), leading to superior ozonation activity to degrade toluene and intermediates. Meanwhile, free radical detection and scavenger tests indicated that ^•OH is the primary ROS during toluene ozonation rather than ¹O₂ or O₂^-.

Catalytic removal of 2-butanone with ozone over porous spent fluid catalytic cracking catalyst

To remove harmful volatile organic compounds (VOCs) including 2-butanone (methyl ethyl ketone, MEK) emitted from various industrial plants is very important for the clean air. Also, it is worthwhile to recycle porous spent fluid catalytic cracking (SFCC) catalysts from various petroleum refineries in terms of reducing industrial waste and the reuse of discharged resources. Therefore, Mn and Mn-Cu added SFCC (Mn/SFCC and Mn-Cu/SFCC) catalysts were prepared to compare their catalytic efficiencies together with the SFCC catalyst in the ozonation of 2-butanone. Since the SFCC-based catalysts have a structure similar to that of zeolite Y (Y), the Mn-loaded zeolite Y catalyst (Mn/Y) was also prepared to compare its activity for the removal of 2-butanone and ozone to that of the SFCC-based ones at room temperature. Among the five catalysts of this study (Y, Mn/Y, SFCC, Mn/SFCC, and Mn-Cu/SFCC), the Mn-Cu/SFCC and Mn/SFCC catalysts showed the better catalytic decomposition activity than the others. The increased distributions of the Mn³⁺ species and the O_vacancy sites in Mn/SFCC and Mn-Cu/SFCC catalysts which could supply more available active sites for the 2-butanone and ozone removal would enhance the catalytic activity of them.

Thermal Annealing Induced Surface Oxygen Vacancy Clusters in α-MnO2 Nanowires for Catalytic Ozonation of VOCs at Ambient Temperature

Catalytic ozonation has gained considerable interest in volatile organic compound (VOC) elimination due to its mild reaction conditions. However, the low activity and mineralization rate of VOCs over catalysts hinder its practical application. Herein, a series of α-MnO2 nanowire catalysts were prepared via thermal annealing treatment at various temperatures to tailor defect species. Numerous characterization techniques were used and combined to investigate the relationship between activity and microstructure. PALS and XAFS indicated that more unsaturated manganese and oxygen vacancies, especially surface oxygen vacancy clusters, were produced in α-MnO2 under the optimal high calcination temperature. As a result, MnO2-600 was found to exhibit the best-ever performance in toluene conversion (95%) and mineralization rate (89.5%) at 20 °C, making it a promising candidate for practical use. The roles of these defects in manipulating the reactive oxygen species of α-MnO2 were clarified by quantifying the amounts of reactive oxygen species by quenching experiments and density functional theory calculations. 1O2 and ·OH species generated in the vicinity of oxygen vacancy clusters, especially the dimer oxygen vacancy cluster, were identified as key oxygen species in the abatement of toluene. This study provides a facile method to engineer the microstructure of MnO2 by means of the manipulation of oxygen vacancies and an in-depth understanding of their roles in the catalytic ozonation of VOC.

Insights into the influence of water molecules on selective catalytic ozonation of gaseous ammonia into nitrogen on cryptomelane-type manganese oxide using in-situ DRIFTS

Catalytic ozonation is an environmentally friendly technology for the removal of gaseous NH₃ due to high NH₃ conversion and high N₂ selectivity at ambient temperature. However, the influence mechanism of ubiquitous water vapor on catalytic ozonation of NH₃ is unclear. In this study, cryptomelane-type manganese oxide (OMS-2) catalyst was prepared and tested for catalytic ozonation of NH₃ in different relative humidity. The results showed that water vapor significantly decreased the catalytic activity, which was due to the inhibition of water on NH₃ adsorption on Lewis acid sites and O₃ decomposition on oxygen vacancies, as well as the combination of water with active oxygen species (O₂^2- and O_atom). And the effect of water vapor on NH₃ conversion was more significant than O₃ decomposition because more Mn-OH were involved in the O₃ decomposition under humid conditions. Combining in-situ DRIFTS results with the performance of NH₃ oxidation, it is found that L-2 acid sites (the peak of NH₃ adsorption on Lewis acid sites at 1188 cm^-1) were the main active sites for adsorption and activation of NH₃ in the early stage of catalytic reaction; as the reaction progressed, L-2 acid sites were gradually occupied by water and more Brønsted acid sites participated in the catalytic reaction. This work deepened the understanding of the reaction process for selective catalytic ozonation of NH₃, and provided theoretical guidance for the design of efficient hydrophobic catalysts to eliminate gaseous NH₃ pollution.

Autothermal Reforming of Volatile Organic Compounds to Hydrogen-Rich Gas

Industrial emissions of volatile organic compounds are urgently addressed for their toxicity and carcinogenicity to humans. Developing efficient and eco-friendly reforming technology of volatile organic compounds is important but still a great challenge. A promising strategy is to generate hydrogen-rich gas for solid oxide fuel cells by autothermal reforming of VOCs. In this study, we found a more desirable commercial catalyst (NiO/K₂O-γ-Al₂O₃) for the autothermal reforming of VOCs. The performance of autothermal reforming of toluene as a model compound over a NiO/K₂O-γ-Al₂O₃ catalyst fitted well with the simulation results at the optimum operating conditions calculated based on a simulation using Aspen PlusV11.0 software. Furthermore, the axial temperature distribution of the catalyst bed was monitored during the reaction, which demonstrated that the reaction system was self-sustaining. Eventually, actual volatile organic compounds from the chemical factory (C₉, C₁₀, toluene, paraxylene, diesel, benzene, kerosene, raffinate oil) were completely reformed over NiO/K₂O-γ-Al₂O₃. Reducing emissions of VOCs and generating hydrogen-rich gas as a fuel from the autothermal reforming of VOCs is a promising strategy.

Optimization of photothermal conversion and catalytic sites for photo-assisted-catalytic degradation of volatile organic compounds

Solar energy conversion is a promising strategy to enhance the elimination of volatile organic compounds (VOCs) and minimize power consumption. Herein, non-noble metal WC@WO₃ as cocatalyst was composited with CeO₂ to optimize photochemical and photothermal conversion for the catalytic ozonation of toluene and acetone. The photothermal conversion efficiencies of visible and infrared lights on 20%WC@WO₃-CeO₂ were 2.2 and 10.4 times higher than those on CeO₂, respectively, which indicates that the equilibrium temperature of the catalyst remarkably increased under full-spectrum light irradiation. Moreover, WC@WO₃ transferred electrons to CeO₂ in 20%WC@WO₃-CeO₂ and thus remarkably improved the activity of catalytic sites. The synergy factor of light and O₃ on 20%WC@WO₃-CeO₂ was 5.8, and the reaction rate of toluene and acetone reached 9274.5 and 35779.0 mg/(m³∙min), respectively. This work provides a low-cost and high-efficient catalyst for the utilization of solar energy for VOC control.

A pilot lab trial for enhanced oxidative transformation of procymidone fungicide and its aniline metabolite using heterogeneous MnO2 catalysts

In this study, the feasibility of two heterogeneous catalysis (non-Fenton heterogeneous catalysis and catalytic ozonation) was evaluated for the oxidative transformation of the fungicide procymidone and its major metabolite (3,5-dichloroaniline; 3,5-DCA) under a pilot lab experiment. Among the studied treatments, only H₂O₂ or O₃ significantly oxidized procymidone and 3,5-DCA. However, heterogeneous catalysis used with various types of MnO₂ catalysts was found to be an effective rapid strategy for transformation of procymidone and its aniline metabolite. Among the studied catalysts, δ-MnO₂ performed well in the enhanced oxidative transformation of procymidone and 3,5-DCA in MnO₂-mediator system assay. The optimal reaction parameters, such as reaction pH, and initial catalyst concentration were comparatively evaluated. However, heterogeneous catalysis and catalytic ozonation were revealed as the rapid strategy for oxidative transformation of investigated procymidone and 3,5-DCA as compared to single oxidation by peroxide/ozone. Finally, as a novel insight of this investigation, a postulated reaction mechanism underlying the accelerated transformation of aniline metabolites via heterogeneous catalysis was explored. The findings of this study will open new avenues for evaluating heterogeneous catalysis during oxidative transformation of non-phenolic pollutants in both lab trial and field applications. This study can be expanded for use in actual field settings, using environmental samples from contaminated areas exposed to non-phenolic pesticides and their metabolites.

Catalytic Degradation of Toluene over MnO2/LaMnO3: Effect of Phase Type of MnO2 on Activity

Series of α, β, γ, δ type MnO2 supported on LaMnO3 perovskite was developed by a one-pot synthesis route. Compared with α-MnO2, β-MnO2, γ-MnO2, δ-MnO2 and LaMnO3 oxides, all MnO2/LaMnO3 showed promotional catalytic performance for toluene degradation. Among them, α-MnO2/LaMnO3 holds the best active and mineralization efficiency. By the analysis of N2 adsorption-desorption, XPS and H2-TPR, it can be inferred that the improved activity should be ascribed to the higher proportion of lattice oxygen, better low-temperature reducibility and larger specific surface area. Besides, the byproducts from the low-temperature reaction of toluene oxidation were detected by a TD/GC-MS, confirming the presence of the intermediates. Combined with the in-situ DRIFTS, the catalytic degradation path of toluene oxidation has also been discussed in depth.

Promoting the Catalytic Ozonation of Toluene by Introducing SO42- into the α-MnO2/ZSM-5 Catalyst to Tune Both Oxygen Vacancies and Acid Sites

Mn-based catalysts hold the promise of practical applications in catalytic ozonation of toluene at room temperature, yet improvement of toluene conversion and CO_x selectivity remains challenging. Here, an innovative α-MnO₂/ZSM-5 catalyst modified with SO₄^2- was successfully prepared, and both characterizations and density functional theory (DFT) calculations showed that SO₄^2- introduction facilitated the formation of oxygen vacancies, Lewis and Brönsted acid sites, and active oxygen species and enhanced the adsorption ability of toluene on α-MnO₂/ZSM-5. Characterizations also showed that SO₄^2- introduction made the catalyst possess larger specific surface area, superior reducibility, and stronger surface acidity. As a result, α-MnO₂/ZSM-5 with a S/Mn molar ratio of 0.019 exhibited the best toluene conversion and CO_x selectivity, 87 and 94%, respectively, after the reaction for 8 h at 30 °C under an initial concentration of 5 ppm toluene and 45 ppm ozone, relative humidity of 45%, and space velocity of 32,000 h^-1, far superior to those of non-noble catalysts reported to date under comparable reaction conditions. The synergistic role of increased oxygen vacancies and acid sites of α-MnO₂/ZSM-5 modified with SO₄^2- resulted in excellent toluene conversion and CO_x selectivity. The findings represented a critical step toward the rational design and synthesis of highly efficient catalysts for catalytic ozonation of toluene.

Tuning the Micro-coordination Environment of Al in Dealumination Y Zeolite to Enhance Electron Transfer at the Cu-Mn Oxides Interface for Highly Efficient Catalytic Ozonation of Toluene at Low Temperatures

The development of stable, highly active, and inexpensive catalysts for the ozone catalytic oxidation of volatile organic compounds (VOCs) is challenging but of great significance. Herein, the micro-coordination environment of Al in commercial Y zeolite was regulated by a specific dealumination method and then the dealuminated Y zeolite was used as the support of Cu-Mn oxides. The optimized catalyst Cu-Mn/DY exhibited excellent performance with around 95% of toluene removal at 30 °C. Besides, the catalyst delivered satisfactory stability in both high-humidity conditions and long-term reactions, which is attributed to more active oxygen vacancies and acidic sites, especially the strong Lewis acid sites newly formed in the catalyst. The decrease in the electron cloud density around aluminum species enhanced electron transfer at the interface between Cu-Mn oxides. Moreover, extra-framework octahedrally coordinated Al in the support promoted the electronic metal-support interaction (EMSI). Compared with single Mn catalysts, the incorporation of the Cu component changed the degradation pathway of toluene. Benzoic acid, as the intermediate of toluene oxidation, can directly ring-open on Cu-doped catalysts rather than being further oxidized to other byproducts, which increased the rate of the catalytic reaction. This work provides a new insight and theoretical guidance into the rational design of efficient catalysts for the catalytic ozonation of VOCs.

Review on Catalytic Oxidation of VOCs at Ambient Temperature

As an important air pollutant, volatile organic compounds (VOCs) pose a serious threat to the ecological environment and human health. To achieve energy saving, carbon reduction, and safe and efficient degradation of VOCs, ambient temperature catalytic oxidation has become a hot topic for researchers. Firstly, this review systematically summarizes recent progress on the catalytic oxidation of VOCs with different types. Secondly, based on nanoparticle catalysts, cluster catalysts, and single-atom catalysts, we discuss the influence of structural regulation, such as adjustment of size and configuration, metal doping, defect engineering, and acid/base modification, on the structure-activity relationship in the process of catalytic oxidation at ambient temperature. Then, the effects of process conditions, such as initial concentration, space velocity, oxidation atmosphere, and humidity adjustment on catalytic activity, are summarized. It is further found that nanoparticle catalysts are most commonly used in ambient temperature catalytic oxidation. Additionally, ambient temperature catalytic oxidation is mainly applied in the removal of easily degradable pollutants, and focuses on ambient temperature catalytic ozonation. The activity, selectivity, and stability of catalysts need to be improved. Finally, according to the existing problems and limitations in the application of ambient temperature catalytic oxidation technology, new prospects and challenges are proposed.

Low-Temperature Catalytic Ozonation of Multitype VOCs over Zeolite-Supported Catalysts

Volatile organic compounds (VOCs) are an important source of air pollution, harmful to human health and the environment, and important precursors of secondary organic aerosols, O₃ and photochemical smog. This study focused on the low-temperature catalytic oxidation and degradation of benzene, dichloroethane, methanethiol, methanol and methylamine by ozone. Benzene was used as a model compound, and a molecular sieve was selected as a catalyst carrier to prepare a series of supported active metal catalysts by impregnation. The effects of ozone on the catalytic oxidation of VOCs and catalysts' activity were studied. Taking benzene as a model compound, low-temperature ozone catalytic oxidation was conducted to explore the influence of the catalyst carrier, the active metal and the precious metal Pt on the catalytic degradation of benzene. The optimal catalyst appeared to be 0.75%Pt-10%Fe/HZSM(200). The catalytic activity and formation of the by-products methylamine, methanethiol, methanol, dichloroethane and benzene over 0.75%Pt-10%Fe/HZSM(200) were investigated. The structure, oxygen vacancy, surface properties and surface acidity of the catalysts were investigated. XRD, TEM, XPS, H₂-TPR, EPR, CO₂-TPD, BET, C₆H₆-TPD and Py-IR were combined to establish the correlation between the surface properties of the catalysts and the degradation activity.