Biopolymer - A sustainable and efficacious material system for effluent removal

Biopolymer-based beads for the adsorptive removal of organic pollutants from wastewater: Current state and future perspectives

Among biopolymer-based adsorbents, composites in the form of beads have shown promising results in terms of high adsorption capacity and ease of separation from the effluents. This review addresses the potential of biopolymer-based beads to remediate wastewaters polluted with emerging organic contaminants, for instance dyes, active pharmaceutical ingredients, pesticides, phenols, oils, polyaromatic hydrocarbons, and polychlorinated biphenyls. High adsorption capacities up to 2541.76 mg g-1 for dyes, 392 mg g-1 for pesticides and phenols, 1890.3 mg g-1 for pharmaceuticals, and 537 g g-1 for oils and organic solvents have been reported. The review also attempted to convey to its readers the significance of wastewater treatment through adsorption by providing an overview on decontamination technologies of organic water contaminants. Various preparation methods of biopolymer-based gel beads and adsorption mechanisms involved in the process of decontamination have been summarized and analyzed. Therefore, we believe there is an urge to discuss the current state of the application of biopolymer-based gel beads for the adsorption of organic pollutants from wastewater and future perspectives in this regard since it is imperative to treat wastewater before releasing into freshwater bodies.

Tailoring electrospun nanocomposite fibers of polylactic acid for seamless methylene blue dye adsorption applications

The introduction of biopolymers, which are sustainable and green materials, desegregated nature's water purification proficiency with science and technology, opens a new sustainable methodology in water reclamation. In order to introduce an efficacious adsorbent system for MB dye-toxic pollutant, adsorption, providing robust mechanical properties and facile processability, a facile system was introduced via electrospinning utilizing polylactic acid (PLA) and Ti3C2Tx, viz., PMX. The addition of 3 wt.% Ti3C2Tx led to a 3-fold substantial augmentation in the uptake capacity of the membrane from 197.28 to 307 mg/g when the adsorbate concentration was 100 ppm. The adsorption followed a PSO behavior, proposing that the rate-limiting stage is chemisorption and data best fitted to Freundlich isotherm, indicating heterogeneous adsorption sites and multi-layer adsorption. Further, biodegradability was studied by simulating natural environmental conditions where the nanofibers exhibited 42-64% degradation after 270 days. Based on the result with PLA, it is anticipated that the prepared fibrous system will introduce a new perspective as a potential candidate for MB removal from wastewater, opening new directions toward the research and development in wastewater treatment with electrospun biopolymer fibers using waste PLA.

Chitosan/functionalized fruit stones as a highly efficient adsorbent biomaterial for adsorption of brilliant green dye: Comprehensive characterization and statistical optimization

In this research, a highly efficient adsorbent biomaterial (hereinafter, CTS/PPS-HS) of chitosan/functionalized fruit stones (peach and plum) with H2SO4 was produced for the adsorption of brilliant green (BG) dye from aquatic systems. The developed biomaterial was characterized by several techniques like SEM-EDX, FTIR, XRD, BET, and pHpzc. To systematically optimize the adsorption performance of CTS/PPS-HS, the Box-Behnken design (BBD) based on response surface methodology (RSM) was attained. The factors considered for optimization included A: CTS/PPS-HS dosage (0.02-0.08 g), B: pH (4-10), and C: removal time (10-60 min). The pseudo-first-order and Langmuir isotherm models exhibited excellent agreement with the experimental results of BG adsorption by CTS/PPS-HS. The outstanding adsorption capacity (409.63 mg/g) of CTS/PPS-HS was obtained. The remarkable adsorption of BG onto CTS/PPS-HS can be primarily attributed to electrostatic forces between the acidic sites of CTS/PPS-HS and the BG cations, accompanied by interactions such as π-π, Yoshida H-bonding, n-π, and H-bond interactions. The current data underscores the significant potential inherent in combining biomass with CTS polymer to create an exceptionally effective adsorbent biomaterial tailored for the elimination of cationic dyes.

Revealing the interface chemistry of polyaniline grafted biomass via statistical modeling of multi-component dye systems: optimization, kinetics, thermodynamics, and adsorption mechanism

The growing need to examine the adsorption capabilities of innovative materials in real-world water samples has encouraged a shift from single to multicomponent adsorption systems. In this study, a novel composite, PANI-g-SM was synthesized by covalently grafting a lignocellulosic biomass, Saccharum munja (SM) with polyaniline (PANI). The as-synthesized composite was investigated for the simultaneous adsorption of cationic (Methylene Blue (MB); Crystal Violet (CV)) and anionic dyes (Reactive Red 35 (RR); Fast Green FCF (FG)) from four single components and two binary systems, MB + RR and CV + FG. Further, the effect and interaction of pH (2-11), dosage (0.01-0.04 g/10 mL), and initial concentration (0.0313 to 0.1563 mmol/L) on the elimination of dyes by PANI-g-SM were studied through a novel design of Box-Behnken of Response Surface Methodology (RSM) technique which was found to be highly useful for revealing the chemistry of interfaces in multi-component systems. The extended Langmuir model for the binary system indicated the presence of synergism, as result the maximum monolayer adsorption capacity increased by 44.44%, 645.83%, 67.88%, and 441.07% for MB, RR, CV, and FG dye, respectively. Further, the adsorption process mainly followed a pseudo-second-order kinetic model, and the thermodynamic studies revealed the exothermic nature of adsorption for RR and FG dye while endothermic for MB and CV dye, respectively with Δ G varying from - 1.68 to - 6.12 kJ/mol indicating the spontaneity of the process. Importantly, the efficacy of the composite was evaluated for the treatment of textile industry effluent highlighting its potential as an adsorbent for wastewater treatment.

Assessment of biodegradation of lignocellulosic fiber-based composites - A systematic review

Lignocellulosic fiber-reinforced polymer composites are the most extensively used modern-day materials with low density and better specific strength specifically developed to render better physical, mechanical, and thermal properties. Synthetic fiber-reinforced composites face some serious issues like low biodegradability, non-environmentally friendly, and low disposability. Lignocellulosic or natural fiber-reinforced composites, which are developed from various plant-based fibers and animal-based fibers are considered potential substitutes for synthetic fiber composites because they are characterized by lightweight, better biodegradability, and are available at low cost. It is very much essential to study end-of-life (EoL) conditions like biodegradability for the biocomposites which occur commonly after their service life. During biodegradation, the physicochemical arrangement of the natural fibers, the environmental conditions, and the microbial populations, to which the natural fiber composites are exposed, play the most influential factors. The current review focuses on a comprehensive discussion of the standards and assessment methods of biodegradation in aerobic and anaerobic conditions on a laboratory scale. This review is expected to serve the materialists and technologists who work on the EoL behaviour of various materials, particularly in natural fiber-reinforced polymer composites to apply these standards and test methods to various classes of biocomposites for developing sustainable materials.

Biopolymers as a Potential Alternative for the Retention of Pollutants from Vinasse: An In Silico Approach

Vinasse, a waste from the bioethanol industry, presents a crucial environmental challenge due to its high organic matter content, which is difficult to biodegrade. Currently, no sustainable alternatives are available for treating the amount of vinasse generated. Conversely, biopolymers such as cellulose, carboxymethylcellulose, and chitosan are emerging as an interesting alternative for vinasse control due to their flocculating capacity against several organic compounds. This study seeks to determine the thermodynamic behavior of in silico interactions among three biopolymers (cellulose, carboxymethylcellulose, and chitosan) regarding 15 organic compounds found in vinasse. For this, the Particle Mesh Ewald (PME) method was used in association with the Verlet cutoff scheme, wherein the Gibbs free energy (ΔG) was calculated over a 50 ns simulation period. The findings revealed that cellulose showed a strong affinity for flavonoids like cyanidin, with a maximum free energy of -84 kJ/mol and a minimum of -55 kJ/mol observed with phenolic acids and other flavonoids. In contrast, chitosan displayed the highest interactions with phenolic acids, such as gallic acid, reaching -590 kJ/mol. However, with 3-methoxy-4-hydroxyphenyl glycol (MHPG), it reached an energy of -70 kJ/mol. The interaction energy for flavonoid ranged from -105 to -96 kJ/mol. Finally, carboxymethylcellulose (CMC) demonstrated an interaction energy with isoquercetin of -238 kJ/mol, while interactions with other flavonoids were almost negligible. Alternatively, CMC exhibited an interaction energy of -124 kJ/mol with MHPG, while it was less favorable with other phenolic acids with minimal interactions. These results suggest that there are favorable interactions for the interfacial sorption of vinasse contaminants onto biopolymers, indicating their potential for use in the removal of contaminants from the effluents of the bioethanol industry.

Bio-based functionalized adsorptive polymers for sustainable water decontamination: A systematic review of challenges and real-world implementation

The overwhelming concerns of water pollution, industrial discharges and environmental deterioration by various organic and inorganic substances, including dyes, heavy metals, pesticides, pharmaceuticals, and detergents, intrinsically drive the search for urgent and efficacious decontamination techniques. This review illustrates the various approaches to remediation, their fundamentals, characteristics and demerits. In this manner, the advantageous implementation of nature-based adsorbents has been outlined and discussed. Different types of lignocellulosic compounds (cellulose, lignin, chitin, chitosan, starch) have been introduced, and the most used biopolymeric materials in bioremediation have been highlighted; their merits, synthesis methods, properties and performances in aqueous medium decontamination have been described. The literature assessment reveals the genuine interest and dependence of academic and industrial fields to valorize biopolymers in the adsorption of various hazardous substances. Yet, the full potential of this approach is still confined by certain constraints, such as the lack of reliable, substantial, and efficient extraction of biopolymers, as well as their modest and inconsistent physicochemical properties. The futuristic reliance on such biomaterials in all fields, rather than adsorption, is inherently reliable on in-depth investigations and understanding of their features and mechanisms, which can guarantee a real-world application and green technologies.

Mechanochemical synthesis of cysteine-gum acacia intermolecular complex for multiple metal(loid) sequestration from herbal extracts

The ubiquitous heavy metal(loid)s (HMs) contamination has triggered great concern about food safety, while sequestration and separation of trace HMs from herbal extracts still calls for appropriate sorbent materials. In this work, gum acacia was modified by cysteine to form a cysteine-acacia intermolecular complex (Cys-GA complex) via facile mechanochemical synthesis, aiming at capturing multiple HMs simultaneously. Preliminary screening confirms the superiority of Cys-CA complex for both cationic and anionic HMs, and determines an optimum Cys/GA mass ratio of 9:1 to achieve high removal capacities for Pb(II) (938 mg g-1), Cd(II) (834 mg g-1), As(V) (496 mg g-1), and Cr(VI) (647 mg g-1) in simulated aqueous solution. The analysis on HMs-exhausted Cys-GA complex indicates that Pb(II), As(V), and Cr(VI) tend to be removed through chelation, electrostatic attraction, and reduction, while Cd(II) can only be chelated or adsorbed by electrostatic interaction. The batch experiments on commercial herbal (e.g. Panax ginseng, Glycine max, Sophora flavescens, Gardenia jasminoides, Cyclocarya paliurus, and Bamboo leaf) extracts indicate that Cys-GA complex can reduce HMs concentration to attain acceptable level that comply with International Organization for Standardization, with negligible negative effect on its active ingredients. This work provides a practical and convenient strategy to purify HMs-contaminated foods without introducing secondary pollution.

Next-Generation Water Treatment: Exploring the Potential of Biopolymer-Based Nanocomposites in Adsorption and Membrane Filtration

This review article focuses on the potential of biopolymer-based nanocomposites incorporating nanoparticles, graphene oxide (GO), carbon nanotubes (CNTs), and nanoclays in adsorption and membrane filtration processes for water treatment. The aim is to explore the effectiveness of these innovative materials in addressing water scarcity and contamination issues. The review highlights the exceptional adsorption capacities and improved membrane performance offered by chitosan, GO, and CNTs, which make them effective in removing heavy metals, organic pollutants, and emerging contaminants from water. It also emphasizes the high surface area and ion exchange capacity of nanoclays, enabling the removal of heavy metals, organic contaminants, and dyes. Integrating magnetic (Fe2O4) adsorbents and membrane filtration technologies is highlighted to enhance adsorption and separation efficiency. The limitations and challenges associated are also discussed. The review concludes by emphasizing the importance of collaboration with industry stakeholders in advancing biopolymer-based nanocomposites for sustainable and comprehensive water treatment solutions.

Cerium(IV) chitosan-based hydrogel composite for efficient adsorptive removal of phosphates(V) from aqueous solutions

The excess presence of phosphate(V) ions in the biosphere is one of the most serious problems that negatively affect aqueous biocenosis. Thus, phosphates(V) separation is considered to be important for sustainable development. In the presented study, an original cerium(IV)-modified chitosan-based hydrogel (Ce-CTS) was developed using the chemical co-precipitation method and then used as an adsorbent for efficient removal of phosphate(V) ions from their aqueous solutions. From the scientific point of view, it represents a completely new physicochemical system. It was found that the adsorptive removal of phosphate(V) anions by the Ce-CTS adsorbent exceeded 98% efficiency which is ca. 4-times higher compared with the chitosan-based hydrogel without any modification (non-cross-linked CTS). The best result of the adsorption capacity of phosphates(V) on the Ce-CTS adsorbent, equal to 71.6 mg/g, was a result of adsorption from a solution with an initial phosphate(V) concentration 9.76 mg/dm3 and pH 7, an adsorbent dose of 1 g/dm3, temperature 20 °C. The equilibrium interphase distribution data for the Ce-CTS adsorbent and aqueous solution of phosphates(V) agreed with the theoretical Redlich-Peterson and Hill adsorption isotherm models. From the kinetic point of view, the pseudo-second-order model explained the phosphates(V) adsorption rate for Ce-CTS adsorbent the best. The specific effect of porous structure of adsorbent influencing the diffusional mass transfer resistances was identified using Weber-Morris kinetic model. The thermodynamic study showed that the process was exothermic and the adsorption ran spontaneously. Modification of CTS with cerium(IV) resulted in the significant enhancement of the chitosan properties towards both physical adsorption (an increase of the point of zero charge of adsorbent), and chemical adsorption (through the presence of Ce(IV) that demonstrates a chemical affinity for phosphate(V) anions). The elaborated and experimentally verified highly effective adsorbent can be successfully applied to uptake phosphates(V) from aqueous systems. The Ce-CTS adsorbent is stable in the conditions of the adsorption process, no changes in the adsorbent structure or leaching of the inorganic filling were observed.

Microbial extracellular polymeric substances alleviate cadmium toxicity in rice (Oryza sativa L.) by regulating cadmium uptake, subcellular distribution and triggering the expression of stress-related genes

Cadmium (Cd) accumulation in crops causes potential risks to human health. Microbial extracellular polymeric substances (EPS) are a complex mixture of biopolymers that can bind various heavy metals. The present work examined the alleviating effects of EPS on Cd toxicity in rice and its detoxification mechanism. The 100 μM Cd stress hampered the overall plant growth and development, damaged the ultrastructures of both leaf and root cells, and caused severe lipid peroxidation in rice plants. However, applying EPS at a concentration of 100 mg/L during Cd stress resulted in increased biomass, reduced Cd accumulation and transport, and minimized the oxidative damage. EPS application also enhanced Cd retention in the shoot cell walls and root vacuoles, and actively altered the expression of genes involved in cell wall formation, antioxidant defense systems, transcription factors, and hormone metabolism. These findings provide new insights into EPS-mediated mitigation of Cd stress in plants and help us to develop strategies to improve crop yield in Cd-contaminated soils in the future.

Algal mediated intervention for the retrieval of emerging pollutants from aqueous media

Water is a crucial elemental contributor for all sectors; however, the agricultural sector alone accounts for 70% of the world's total water withdrawal. The anthropogenic activity from various industries including agriculture, textiles, plastics, leather, and defence has resulted in the release of contaminants into water systems, resulting harm to the ecosystem and biotic community. Algae-based organic pollutant removal uses several methods, such as biosorption, bioaccumulation, biotransformation, and biodegradation. The adsorption of methylene blue by algal species Chlamydomonas sp. showed a maximum adsorption capacity of 2744.5 mg/g with 96.13% removal efficiency; on the other hand, Isochrysis galbana demonstrated a maximum of 707 µg/g nonylphenol accumulation in the cell with 77% removal efficiency indicating the potential of algal systems as efficient retrieval system for organic contaminants. This paper is a compilation of detailed information about biosorption, bioaccumulation, biotransformation, biodegradation, and their mechanism, along with the genetic alteration of algal biomass. Where the genetic engineering and mutations on algae can be advantageously utilized for the enhancement of removal efficiency without any secondary toxicity.

Natural and Natural-Based Polymers: Recent Developments in Management of Emerging Pollutants

Anthropogenic activities lead to the issue of new classes of pollutants in the environment that are not currently monitored in environmental studies. This category of pollutants (known as emerging contaminants) includes a very wide range of target substances, such as pharmaceuticals, plant protection products, personal care products, dyes, toxins, microplastics and many other industrially important intermediaries. Together with an increasing demand for clean water (both for agricultural necessities and for the increasing population consumption), the need for the removal of emerging pollutants, simultaneously with the current "green chemistry" approach, opens the door for the industrial application of natural polymers in the area of environmental protection. Recent developments in this area are presented in this paper, as well as the application of these particular natural materials for the removal of other contaminants of interest (such as radioisotopes and nanoparticles). The current knowledge regarding the processes' kinetics is briefly presented, as well as the future development perspectives in this area.

Preparation and Characterization of di- and Tricarboxylic Acids-Modified Arabinogalactan Plasticized Composite Films

To ensure the high quality of water, it is necessary to remove toxic pollutants. At present, purification of water is implemented using various sorbents. The efficient sorption materials are modified polysaccharides. In this study, we report on a new environmentally friendly method for modifying larch hemicellulose-arabinogalactan (AG)-with polybasic carboxylic acids (citric, succinic, oxalic, and adipic) to obtain composite materials. The synthesized AG derivatives have been explored by a complex of physicochemical methods, including gel permeation chromatography (GPC), Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), X-ray diffractometry (XRD), scanning electron microscopy (SEM), and sorption capacity investigations. It is shown that the heat treatment results in the formation of additional inter- and intramolecular bonds between carboxylic acids and polysaccharide molecules. The formation of ester bonds has been confirmed by the appearance of absorption bands in the IR spectra in the range of 1750-1690 cm^-1. It has been found, using the TGA study, that the most thermally stable (up to 190 °C) sample is arabinogalactan oxalate obtained under heat treatment. The SEM study of the synthesized AG films has shown that the modified samples have the homogeneous film surface ensured by cross-linking. It has been established, when studying the sorption properties of the AG derivatives, that AG succinate (82.52%) obtained by lyophilization has the highest sorption capacity, due to the developed mesoporous surface, which, in turn, makes the synthesized films promising eco-friendly materials for use as drug carriers, sorbents, and water treatment agents.

Processing, Characterization and Disintegration Properties of Biopolymers Based on Mater-Bi® and Ellagic Acid/Chitosan Coating

Among the most promising synthetic biopolymers to replace conventional plastics in numerous applications is MaterBi^® (MB), a commercial biodegradable polymer based on modified starch and synthetic polymers. Actually, MB has important commercial applications as it shows interesting mechanical properties, thermal stability, processability and biodegradability. On the other hand, research has also focused on the incorporation of natural, efficient and low-cost active compounds into various materials with the aim of incorporating antimicrobial and/or antioxidant capacities into matrix polymers to extend the shelf life of foods. Among these is ellagic acid (EA), a polyphenolic compound abundant in some fruits, nuts and seeds, but also in agroforestry and industrial residues, which seems to be a promising biomolecule with interesting biological activities, including antioxidant activity, antibacterial activity and UV-barrier properties. The objective of this research is to develop a film based on commercial biopolymer Mater-Bi^® (MB) EF51L, incorporating active coating from chitosan with a natural active compound (EA) at two concentrations (2.5 and 5 wt.%). The formulations obtained complete characterization and were carried out in order to evaluate whether the incorporation of the coating significantly affects thermal, mechanical, structural, water-vapor barrier and disintegration properties. From the results, FTIR analysis yielded identification, through characteristic peaks, that the type of MB used is constituted by three polymers, namely PLA, TPS and PBAT. With respect to the mechanical properties, the values of tensile modulus and tensile strength of the MB-CHI film were between 15 and 23% lower than the values obtained for the MB film. The addition of 2.5 wt.% EA to the CHI layer did not generate changes in the mechanical properties of the system, whereas a 5 wt.% increase in ellagic acid improved the mechanical properties of the CHI film through the addition of natural phenolic compounds at high concentrations. Finally, the disintegration process was mainly affected by the PBAT biopolymer, causing the material to not disintegrate within the times indicated by ISO 20200.

A review on algal biosorbents for heavy metal remediation with different adsorption isotherm models

Biosorbent composites like chitin, alginate, moss, xanthene, and cotton can be derived from biotic species such as plants, algae, fungi, and bacteria which can be used for the exclusion of both organic and inorganic toxicants from sewage, industrial effluent, polluted soils, and many more. The use of composites in place of raw substrates like alginate and chitin increases the adsorption capacity as CS₄CPL₁ beads increase the adsorption capacity for copper and nickel from 66.7 mg/g and 15.3 mg/g in the case of alginate microsphere to 719.38 mg/g and 466.07 mg/g respectively. Biosorbent fabricated from algae Chlorella vulgaris having surface area of 12.1 m²/g and pore size of 13.7 nm owing to which it displayed a higher adsorption capacity for Pb 0.433 mmol/g indicating their potential as an efficient biosorbent material. This article contains detailed information related to heavy metals as well as biosorbent that includes different isotherms, kinetics, techniques to estimate heavy metal concentration, removal methods, and adverse health effects caused due to heavy metal pollution. Apart from the above recovery and reuse of biosorbent, correlation with the sustainable development goals has also been included.

Application of neural network in metal adsorption using biomaterials (BMs): a review

ANN models for predicting wastewater treatment efficacy of biomaterial adsorbents.