Efficient photocatalytic degradation of toxic Alizarin yellow R dye from industrial wastewater using biosynthesized Fe nanoparticle and study of factors affecting the degradation rate

Ternary tin-doped titanium dioxide/calcium oxide (Sn-TiO2/CaO) composite as a photocatalyst for efficient removal of toxic dyes

In this study, a novel environmentally friendly route was explored for the synthesis of a tin-doped titanium dioxide/calcium oxide (Sn-TiO2/CaO) composite using eggshell as a ternary photocatalyst. The composite was prepared via a simple hydrothermal method, resulting in a unique material with potential applications in photocatalysis. The prepared photocatalysts were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, UV-vis/diffuse reflectance spectroscopy, scanning electron microscopy, X-ray fluorescence, and the Brunauer-Emmett-Teller techniques. At the same time, the Sn-TiO2/CaO composite shows excellent degradation activity for toxic dyes. The degradation efficiencies for alizarin red, bromophenol blue, methylene blue, malachite green, and methyl red are 68.38%, 62.39%, 76.81%, 86.93%, and 17.52%, respectively, under ultraviolet light irradiation for 35 min at pH = 3. In addition, the best photocatalytic degradation efficiency for zero charge (pH 7) and basic pH is for AR 98.21% and 68.38%, MR 33.01% and 17.52%, BPB 73.17% and 17.52%, MB 72.32% and 76.81%, and MG 85.59% and 86.93%, respectively, under UV light irradiation for 35 min. The increase in photocatalytic activity of the ternary photocatalyst is accredited to the enhancement of electron-hole pair separation. Simultaneous photodegradation and photoreduction of organic dyes show that ternary photocatalysts could be used in real wastewater applications.

Natural waste-derived nano photocatalysts for azo dye degradation

Due to their widespread application in water purification, there is a significant interest in synthesising nanoscale photocatalysts. Nanophotocatalysts are primarily manufactured through chemical methods, which can lead to side effects like pollution, high-energy usage, and even health issues. To address these issues, "green synthesis" was developed, which involves using plant extracts as reductants or capping agents rather than industrial chemical agents. Green fabrication has the benefits of costs less, pollution reduction, environmental protection and human health safety, compared to the traditional methods. This article summarises recent advances in the environmentally friendly synthesis of various nanophotocatalysts employed in the degradation of azo dyes. This study compiles critical findings on natural and artificial methods to achieve the goal. Green synthesis is constrained by the time and place of production and issues with low purity and poor yield, reflecting the complexity of plants' geographical and seasonal distributions and their compositions. However, green photocatalyst synthesis provides additional growth opportunities and potential uses.

Tanning Wastewater Sterilization in the Dark and Sunlight Using Psidium guajava Leaf-Derived Copper Oxide Nanoparticles and Their Characteristics

Employing Psidium guajava (P. guajava) extract from leaves, copper oxide nanoparticles (CuO NPs), likewise referred to as cupric oxide and renowned for their sustainable and harmless biogenesis, have the possibility of being useful for the purification of pollutants as well as for medicinal purposes. The current study examined the generated CuO NPs and their physical qualities by using ultraviolet-visible (UV) spectroscopy. The distinctive peak at 265 nm of the CuO NP production was originally seen. Additionally, an X-ray diffraction (XRD) investigation was conducted to identify the crystalline arrangement of the produced CuO NPs, and a Fourier transform infrared (FTIR) spectroscopy examination was performed to validate the functional compounds of the CuO NPs. Additionally, the synthesized nanoparticles' catalytic activities (wastewater treatment) were analyzed in dark and sunlight modes. The catalytic properties of CuO NPs in total darkness resulted in 64.21% discoloration, whereas exposure to sunshine increased the nanomaterials' catalyst performance to 92.31%. By lowering Cr(VI), Ni, Pb, Co, and Cd in sewage by proportions of 91.4, 80.8, 68.26, 73.25, and 72.4% accordingly, the CuO NP demonstrated its effectiveness as a nanosorbent. Total suspended solids (TSS), total dissolved solids (TDS), chemical oxygen demand (COD), biological demand for oxygen (BOD), and conductance were all successfully reduced by nanotreatment of tanning effluents, with proportion reductions of 93.24, 88.62, 94.21, 87.5, and 98.3%, correspondingly.

Enhancement of photocatalytic activity of Ba-doped CoO for degradation of Emamectin benzoate in aqueous solution

The present study was focused on the preparation of cobalt oxide (CoO) and barium-doped cobalt oxide (Ba-doped CoO) by following the co-precipitation method for the degradation of Emamectin benzoate pesticide in the aqueous medium. The prepared catalysts were characterized using SEM, EDX, and XRD to confirm the formation of catalysts and to observe the variation in the composition of catalysts during the degradation study. It can be suggested from the results of SEM, EDX, XRD, and FTIR analyses that Ba atom has successfully incorporated in the crystalline structure of CoO. The degradation of Emamectin benzoate pesticide was studied under the influence of different factors like solution pH, the dose of catalyst, contact time, temperature, and initial concentration of pesticide. It was observed that solution pH affects the degradation of the pesticide, and maximum degradation (23% and 54%) was found at pH 5.0 and 6.0 using CoO and Ba-doped CoO, respectively. The degradation of pesticides was found to be increased continuously (27-35% in case of CoO while 47-58% in case Ba-doped CoO) with the time of contact. However, the degradation was found to be decreased (23-3% in case of CoO while 47-44% in case Ba-doped CoO) with an increase in temperature. Likewise, in the beginning, degradation was observed to be increased up to some extent with the dose of catalyst and initial concentration of pesticide but started to decrease with further augmentation in the dose of catalyst and initial concentration of pesticide. It may be concluded from this study that doping of Ba considerably enhanced the photocatalytic ability of CoO for Emamectin benzoate pesticide.

Hybrid collagen-cellulose-Fe3O4@TiO2 magnetic bio-sponges derived from animal skin waste and Kenaf fibers for wastewater remediation

Water pollution from synthetic dyes and oil spills has a significant impact on the environment and living species. Here, we developed a low-cost, environmentally friendly and easily biodegradable magnetic hybrid bio-sponge nanocomposite from renewable resources such as collagen and cellulose (Kenaf fibre cellulose-collagen, KFCC). We loaded it with magnetic bimetallic Fe3O4@TiO2 (BFT) NPs to produce a photocatalyst material (KFCC-BFT) for the treatment of colored wastewater as well as a sorbent for oil-water separation. The characterization of the bimetallic BFT NPs by XRD, HRTEM and VSM showed the deposition of TiO2 particles onto the surface of Fe3O4 with lattice interlayers spacing of 0.24 and 0.33 nm for Fe3O4 and TiO2, respectively with ferromagnetic property. The UV-vis diffuse reflectance spectra result indicated that the band gap energy of bio-sponges decreases with the increase of the bimetallic moiety. The photocatalytic efficiency of the as-prepared magnetic hybrid bio-sponge in the degradation of crystal violet dye was up to 91.2% under visible light conditions and 86.6% under direct sunlight exposure. Furthermore, the magnetic hybrid bio-sponge was used to separate motor oil from water (> 99%) and had a high oil sorption capacity of 46.1 g/g. Investigation of the recyclability and reusability performance for 9 cycles revealed that the bio-sponge had a high sorption capacity for up to 5 cycles. Our results suggest that the bio-polymer-supported BFT hybrid nanocomposite is a cost-effective and easily biodegradable photocatalyst and has great potential for real-field environmental remediation applications.

DC magnetic field-assisted improvement of textile dye degradation efficiency with multi-capillary air bubble discharge plasma jet

Axial DC magnetic field-assisted multi-capillary underwater air bubble discharge plasma jet has been used to study the productions of reactive oxygen species. Analyses of optical emission data revealed that the rotational (T_r) and vibrational temperatures (T_v) of plasma species slightly increased with magnetic field strength. The electron temperature (T_e) and density (n_e) increased almost linearly with magnetic field strength. T_e increased from 0.53 to 0.59 eV, whereas n_e increased from 1.03 × 10¹⁵ cm^-3 to 1.33 × 10¹⁵ cm^-3 for B = 0 to B = 374 mT, respectively. Analytical results from the plasma treated water provided that the electrical conductivity (EC), oxidative reduction potential (ORP), and the concentrations of O₃ and H₂ O₂ enhanced from 155 to 229 µS cm^-1, 141 to 17 mV, 1.34 to 1.92 mg L^-1, and 5.61 to 10.92 mg L^-1 due to the influence of axial DC magnetic field, while [Formula: see text] reduced from 5.10 to 3.93 for 30 min treatment of water with B = 0 and B = 374 mT, respectively. The model wastewater prepared with Remazol brilliant blue textile dye and the plasma treated wastewater studied by optical absorption spectrometer, Fourier transform infrared spectrometer, and gas chromatography mass spectrometer. The results show that the decolorization efficiency increased ~ 20% after 5 min treatment for the maximum B = 374 mT with respect to zero-magnetic field and, power consumption, and electrical energy cost reduced ~ 6.3% and ~ 4.5%, respectively, due to the maximum assisted axial DC magnetic field strength of 374 mT.

Green Synthesis of Zinc Oxide Nanoparticles Using an Aqueous Extract of Punica granatum for Antimicrobial and Catalytic Activity

The peel aqueous extract of Punica granatum was utilized to fabricate zinc oxide nanoparticles (ZnO-NPs) as a green approach. The synthesized NPs were characterized by UV-Vis spectroscopy, Fourier transform infrared (FT-IR), X-ray diffraction (XRD), transmission electron microscopy (TEM), and scanning electron microscopy, which was attached to an energy dispersive X-ray (SEM-EDX). Spherical, well arranged, and crystallographic structures of ZnO-NPs were formed with sizes of 10-45 nm. The biological activities of ZnO-NPs, including antimicrobial and catalytic activity for methylene blue dye, were assessed. Data analysis showed that the antimicrobial activity against pathogenic Gram-positive and Gram-negative bacteria, as well as unicellular fungi, was observed to occur in a dose-dependent manner, displaying varied inhibition zones and low minimum inhibitory concentration (MIC) values in the ranges of 6.25-12.5 µg mL^-1. The degradation efficacy of methylene blue (MB) using ZnO-NPs is dependent on nano-catalyst concentration, contact time, and incubation condition (UV-light emission). The maximum MB degradation percentages of 93.4 ± 0.2% was attained at 20 µg mL^-1 after 210 min in presence of UV-light. Data analysis showed that there is no significant difference between the degradation percentages after 210, 1440, and 1800 min. Moreover, the nano-catalyst showed high stability and efficacy to degrade MB for five cycles with decreasing values of 4%. Overall, P. granatum-based ZnO-NPs are promising tools to inhibit the growth of pathogenic microbes and degradation of MB in the presence of UV-light emission.

Efficient degradation of atrazine from synthetic water through photocatalytic activity supported by titanium dioxide nanoparticles

The oxidation of atrazine herbicide from water was performed by using titanium dioxide (TiO2) nanoparticles synthesized via the sol-gel method. A batch-scale photocatalytic reactor was designed for experimental work. The process was monitored using a UV–visible spectrophotometer. Operational parameters such as catalyst loading and pollutant concentration were investigated. The X-ray diffraction confirmed the anatase phase and high purity of the synthesized particles. Fourier transform infrared showed the functional group of titanium (Ti–O–Ti). The morphology of synthesized nanoparticles was characterized by scanning electron microscopy and transmission electron microscopy, which exhibited the irregular shape of nanoparticles along with aggregations. The average size of TiO2 was found to be 56.92 nm as measured from dynamic light scattering analysis. UV–visible spectrometry showed an absorbance of 0.13 (<1). The nanoparticles displayed UV light-responsive catalytic ability with a bandgap energy of 3.14 eV. Furthermore, atrazine was discovered using mass spectrometry, which revealed a clear and sharp peak at 173, 95, and 76 m/z, respectively, at collision energies of 16 and 24 eV. The photocatalytic activity of the TiO2 nanoparticles was examined for the degradation of atrazine. Overall, the obtained results displayed the great efficiency of TiO2 nanoparticles towards ultra-violet light, which was 92.56% at 100 mg of dosages, highlighting the great potential of the photocatalysis process for atrazine degradation. Furthermore, the process followed pseudo-first-order kinetics and the rate was seen to depend on catalyst loading.

Yolk-shell Co3 O4 @Fe3 O4 /C Nanocomposites as a Heterogeneous Fenton-like Catalyst for Organic Dye Removal

The yolk-shell Co₃ O₄ @Fe₃ O₄ /C nanocomposites with Co₃ O₄ as the core, Fe₃ O₄ /C as the shell, and a cavity structure were synthesized by the hard template method. The physical and chemical properties of the composites were characterized by SEM, TEM, XRD, TGA, XPS, BET, and VSM. The specific surface area of yolk-shell Co₃ O₄ @Fe₃ O₄ /C nanocomposites is 175.9 m²  g^-1 , showing superparamagnetic properties. The yolk-shell Co₃ O₄ @Fe₃ O₄ /C nanocomposites were used as heterogeneous Fenton catalysts to activate peroxymonosulfate (PMS) to degrade MB, which showed high catalytic degradation performance. The degradation rate of MB reached 100 % within 30 min under the circumstances of the yolk-shell Co₃ O₄ @Fe₃ O₄ /C nanocomposites dosage of 0.1 g L^-1 , the PMS dosage of 1.0 g L^-1 , the initial MB concentration of 100 mg L^-1 , an initial pH of 5.5, and a temperature of 30±2 °C. The enhanced catalytic performance of the yolk-shell Co₃ O₄ @Fe₃ O₄ /C nanocomposites can be attributed to the synergistic effect of the two catalytically active materials and the middle cavity. The effects of different operating parameters and co-existing anion species on MB degradation were also investigated. Electron paramagnetic resonance (EPR) analysis and quenching experiments confirmed that the formation of SO₄ ⋅^- in the yolk-shell Co₃ O₄ @Fe₃ O₄ /C/PMS system contributes to MB degradation. In addition, yolk-shell Co₃ O₄ @Fe₃ O₄ /C nanocomposites can be easily separated from the pollutant solution under the action of an external magnetic field, and the degradation rate of MB can still reach 98 % after five cycles, indicating that it has good stability and reusability and has broad application prospects in the field of water purification.

Green Synthesis and Photocatalytic Dye Degradation Activity of CuO Nanoparticles

The degradation of dyes is a difficult task due to their persistent and stable nature; therefore, developing materials with desirable properties to degrade dyes is an important area of research. In the present study, we propose a simple, one-pot mechanochemical approach to synthesize CuO nanoparticles (NPs) using the leaf extract of Seriphidium oliverianum, as a reducing and stabilizing agent. The CuO NPs were characterized via X-ray diffraction (XRD), scanning electron microscopy (SEM), photoluminescence (PL) and Fourier-transform infrared spectroscopy (FTIR). The photocatalytic activity of CuO NPs was monitored using ultraviolet-visible (UV-Vis) spectroscopy. The CuO NPs exhibited high potential for the degradation of water-soluble industrial dyes. The degradation rates for methyl green (MG) and methyl orange (MO) were 65.231% ± 0.242 and 65.078% ± 0.392, respectively. Bio-mechanochemically synthesized CuO NPs proved to be good candidates for efficiently removing dyes from water.

A Comprehensive Review on Adsorption, Photocatalytic and Chemical Degradation of Dyes and Nitro-Compounds over Different Kinds of Porous and Composite Materials

Dye and nitro-compound pollution has become a significant issue worldwide. The adsorption and degradation of dyes and nitro-compounds have recently become important areas of study. Different methods, such as precipitation, flocculation, ultra-filtration, ion exchange, coagulation, and electro-catalytic degradation have been adopted for the adsorption and degradation of these organic pollutants. Apart from these methods, adsorption, photocatalytic degradation, and chemical degradation are considered the most economical and efficient to control water pollution from dyes and nitro-compounds. In this review, different kinds of dyes and nitro-compounds, and their adverse effects on aquatic organisms and human beings, were summarized in depth. This review article covers the comprehensive analysis of the adsorption of dyes over different materials (porous polymer, carbon-based materials, clay-based materials, layer double hydroxides, metal-organic frameworks, and biosorbents). The mechanism and kinetics of dye adsorption were the central parts of this study. The structures of all the materials mentioned above were discussed, along with their main functional groups responsible for dye adsorption. Removal and degradation methods, such as adsorption, photocatalytic degradation, and chemical degradation of dyes and nitro-compounds were also the main aim of this review article, as well as the materials used for such degradation. The mechanisms of photocatalytic and chemical degradation were also explained comprehensively. Different factors responsible for adsorption, photocatalytic degradation, and chemical degradation were also highlighted. Advantages and disadvantages, as well as economic cost, were also discussed briefly. This review will be beneficial for the reader as it covers all aspects of dye adsorption and the degradation of dyes and nitro-compounds. Future aspects and shortcomings were also part of this review article. There are several review articles on all these topics, but such a comprehensive study has not been performed so far in the literature.

Efficient photocatalytic degradation of Rhodamine B dye using solar light-driven La-Mn co-doped Fe2O3 nanoparticles

This work aims to develop a highly efficient solar light-induced photocatalyst based on La-Mn co-doped Fe₂O₃ nanoparticles. Pure Fe₂O₃ and La-Mn co-doped Fe₂O₃ nanoparticles were fabricated by a simple co-precipitation method. The photocatalysts were analyzed for their morphological, structural, and magnetic characteristics. Scanning electron microscopy analysis demonstrated the formation of semi-spherical nanoparticles along with small aggregations. The size of nanoparticles was measured using a transmission electron microscope and found in the range of 42-49 nm. The crystalline nature and geometry of synthesized nanoparticles were investigated using X-ray diffraction analysis. Due to the incorporation of La-Mn, the saturation magnetization and remanent magnetization of the nanoparticles decreased from 6.17 to 2.89 emu/g and 1.15 to 0.52 emu/g, respectively, while the coercivity was reduced from 756.72 to 756.67 Oe. The surface area of nanoparticles was increased from 77.93 to 87.45 m²/g as a result of La-Mn co-doping. The photocatalytic performance of the Fe₂O₃, La_0.1Mn_0.3Fe_1.6O₃, and La_0.2Mn_0.2Fe_1.6O₃ catalysts was assessed by their capability to degrade Rhodamine B (RhB) under solar light illumination. La_0.2Mn_0.2Fe_1.6O₃ displayed exceptional degradation performance, degrading RhB to 91.78% in 240 min, in comparison to La_0.1Mn_0.3Fe_1.6O₃ (71.09%) and pristine Fe₂O₃ (58.21%) under specified reaction conditions ((RhB) = 50 ppm; (catalyst) = 40 mg/L; pH = 7; T = 25 °C)). RhB degradation was affected by changing pH, catalytic dosage, dye concentration, and temperature. The degradation of RhB was found to be pseudo-1st order kinetics. The exceptional photocatalytic performance of La_0.2Mn_0.2Fe_1.6O₃ catalysts showed that the synthesized nanoparticles could be effectively utilized to remove organic pollutants from industrial wastewater.

Analysis of Factors Influencing the Efficiency of Catalysts Used in Waste PU Degradation

Polyurethane (PU) is an indispensable part of people's lives. With the development of polyurethane, the disposal of polyurethane waste has become a significant issue around the world. Conventional degradation catalysts have poor dispersion and low degradation efficiency when used in the process of solid degradation into liquid. Therefore, this paper innovatively adopts self-made core-shell nanoscale titanium catalysis, traditional alkali metal catalyst (KOH), and polyol to carry out the glycolysis of waste polyurethane (PU) pipeline foam. The homogenized nanoscale titanium catalyst coated with alcohol gel has an obvious core-shell structure. The alcohol gel not only protects the catalyst but also dissolves with the alcoholysis agent in the process of glycolysis and disperses more evenly into the alcoholysis agent to avoid the phenomenon of nanocatalyst agglomeration, so as to facilitate catalytic cracking without reducing catalyst activity. In this study, investigated and compared the production of renewable polyurethane foam via a one-step method based on use of a homogeneous core-shell nanostructured titanium catalyst vs. a traditional alkaline catalyst in terms of the properties of regenerated polyether polyols as well as of the foams produced from these polyols. The physicochemical properties of regenerated polyether polyols that were analyzed included viscosity, hydroxyl value, and average molecular weight. The regenerated polyurethane foams were characterized based on water absorption, TG, SEM, and thermal conductivity analyses. The results show that, when the addition of homogeneous titanium catalyst was T2 0.050 wt.%, the viscosity of regenerated polyether polyols was the lowest, at 5356.7 mPa·s, which was reduced by 9.97% compared with those obtained using the alkali metal catalyst (KOH). When the amount of titanium catalyst was T3 0.075 wt.%, the hard foam made of regenerated polyurethane prepared by the catalyst showed the best properties, with a compressive strength of 0.168 MPa, which is 4.76% higher than that of the foam prepared using KOH catalyst.

Application of visible light active photocatalysis for water contaminants: A review

Organic water pollutants are ubiquitous in the natural environment arising from domestic products as well as current and legacy industrial processes. Many of these organic water pollutants are recalcitrant and only partially degraded using conventional water and wastewater treatment processes. In recent decades, visible light active photocatalyst has gained attention as a non-conventional alternative for the removal of organic pollutants during water treatment, including industrial wastewater and drinking water treatment. This paper reviews the current state of research on the use of visible light active photocatalysts, their modified methods, efficacy, and pilot-scale applications for the degradation of organic pollutants in water supplies and waste streams. Initially, the general mechanism of the visible light active photocatalyst is evaluated, followed by an overview of the major synthesis techniques. Because few of these photocatalysts are commercialized, particular attention was given to summarizing the different types of visible light active photocatalysts developed to the pilot-scale stage for practical application and commercialization. The organic pollutant degradation ability of these visible light active photocatalysts was found to be considerable and in many cases comparable with existing and commercially available advanced oxidation processes. Finally, this review concludes with a summary of current achievements and challenges as well as possible directions for further research. PRACTITIONER POINTS: Visible light active photocatalysis is a promising advanced oxidation process (AOP) for the reduction of organic water pollutants. Various mechanisms of photocatalysis using visible light active materials are identified and discussed. Many recent photocatalysts are synthesized from renewable materials that are more sustainable for applications in the 21st century. Only a small number of pilot-scale applications exist and these are outlined in this review.

Serratula coronata L. Mediated Synthesis of ZnO Nanoparticles and Their Application for the Removal of Alizarin Yellow R by Photocatalytic Degradation and Adsorption

In this study, the potential of biogenic zinc oxide nanoparticles (ZnO NPs) in the removal of alizarin yellow R (AY) from aqueous solutions by photocatalytic degradation, as well as adsorption, was investigated. The synthesized ZnO NPs were prepared by the simple wet-combustion method using the plant extract of Serratula coronata L. as a reducing and stabilizing agent and characterized by powder X-ray diffraction, scanning electron microscopy, energy dispersive X-ray and X-ray photoelectron spectroscopy. Photocatalytic degradation of AY was monitored by UV-visible spectroscopy and the effects of parameters, such as light source type (UV-, visible- and sunlight), incubation time, pH, catalyst dosage and temperature on degradation were investigated. It was demonstrated that the source of light plays an important role in the efficiency of the reaction and the UV-assisted degradation of AY was the most effective, compared to the others. The degradation reaction of AY was found to follow the Langmuir-Hinshelwood mechanism and a pseudo-first-order kinetic model. The degradation kinetics of AY accelerated with increasing temperature, and the lowest activation energy (E_a) was calculated as 3.4 kJ/mol for the UV-light irradiation system, while the E_a values were 4.18 and 7.37 kJ/mol for visible light and sunlight, respectively. The dye removal by the adsorption process was also affected by several parameters, such as pH, sorbent amount and contact time. The data obtained in the kinetics study fit the pseudo-second-order equation best model and the rate constant was calculated as 0.001 g/mg·min. The isotherm analysis indicated that the equilibrium data fit well with the Freundlich isotherm model. The maximum adsorption capacity of AY on biogenic ZnO NPs was 5.34 mg/g.

Development of Iron Nanoparticles (FeNPs) Using Biomass of Enterobacter: Its Characterization, Antimicrobial, Anti-Alzheimer's, and Enzyme Inhibition Potential

Nanotechnology is a new field that has gained considerable importance due to its potential uses in the field of biosciences, medicine, engineering, etc. In the present study, bio-inspired metallic iron nanoparticles (FeNPs) were prepared using biomass of Enterobacter train G52. The prepared particles were characterized by UV-spectroscopy, TGA, XRD, SEM, EDX, and FTIR techniques. The crystalline nature of the prepared FeNPs was confirmed by XRD. The SEM techniques revealed the particles size to be 23 nm, whereas in FTIR spectra the peaks in the functional group region indicated the involvement of bioactive compounds of selected bacterial strains in the capping of FeNPs. The EDX confirmed the presence of iron in the engineered FeNPs. The FeNPs were then evaluated for its antibacterial, antifungal, antioxidant, anti-inflammatory, anti-Alzheimer's, anti-larvicidal, protein kinase inhibition, anti-diabetic, and biocompatibility potentials using standard protocols. Substantial activities were observed in almost all biological assays used. The antioxidant, anti-cholinesterase, and anti-diabetic potential of the prepared nanoparticles were high in comparison to other areas of biological potential, indicating that the FeNPs are capable of targeting meditators of oxidative stress leading to diabetes and Alzheimer's disease. However, the claim made needs some further experimentation to confirm the observed potential in in vivo animal models.

Light enhanced the antimicrobial, anticancer, and catalytic activities of selenium nanoparticles fabricated by endophytic fungal strain, Penicillium crustosum EP-1

Selenium nanoparticles (Se-NPs) has recently received great attention over owing to their superior optical properties and wide biological and biomedical applications. Herein, crystallographic and dispersed spherical Se-NPs were green synthesized using endophytic fungal strain, Penicillium crustosum EP-1. The antimicrobial, anticancer, and catalytic activities of biosynthesized Se-NPs were investigated under dark and light (using Halogen tungsten lamp, 100 Watt, λ > 420 nm, and light intensity of 2.87 W m⁻²) conditions. The effect of Se-NPs was dose dependent and higher activities against Gram-positive and Gram-negative bacteria as well different Candida spp. were attained in the presence of light than obtained under dark conditions. Moreover, the viabilities of two cancer cells (T47D and HepG2) were highly decreased from 95.8 ± 2.9% and 93.4 ± 3.2% in dark than those of 84.8 ± 2.9% and 46.4 ± 3.3% under light-irradiation conditions, respectively. Significant decreases in IC₅₀ values of Se-NPs against T47D and HepG2 were obtained at 109.1 ± 3.8 and 70.4 ± 2.5 µg mL⁻¹, respectively in dark conditions than 19.7 ± 7.2 and 4.8 ± 4.2 µg mL⁻¹, respectively after exposure to light-irradiation. The photoluminescence activity of Se-NPs revealed methylene blue degradation efficiency of 89.1 ± 2.1% after 210 min under UV-irradiation compared to 59.7 ± 0.2% and 68.1 ± 1.03% in dark and light conditions, respectively. Moreover, superior stability and efficient MB degradation efficiency were successfully achieved for at least five cycles.

Recent developments in photocatalysis of industrial effluents ։ A review and example of phenolic compounds degradation

Industrial expansion and increased water consumption have created water scarcity concerns. Meanwhile, conventional wastewater purification methods have failed to degrade recalcitrant pollutants efficiently. The present review paper discusses the recent advances and challenges in photocatalytic processes applied for industrial effluents treatment, with respect to phenolic compounds degradation. Key operational parameters including the catalyst loading, light intensity, initial pollutants concentration, pH, and type and concentrations of oxidants are evaluated and discussed. Compared to the other examined controlling parameters, pH has the highest effect on the photo-oxidation of contaminants by means of the photocatalyst ionization degree and surface charge. Furthermore, major phenolic compounds derived from industrial sources are comprehensively presented and the applicability of photocatalytic processes and the barriers in practical applications, including high energy demand, technical challenges, photocatalyst stability, and recyclability have been explored. The importance of energy consumption and operational costs for realistic large-scale processes are also discussed. Finally, research gaps in this area and the suggested direction for improving degradation efficiencies in industrial applications are presented. In the light of these premises, selective degradation processes in real water matrices such as untreated sewage are proposed.

Testing of photocatalytic potential of silver nanoparticles produced through nonthermal plasma reduction reaction and stabilized with saccharides

In this study, silver nanoparticles (AgNPs) were produced through an atmospheric pressure plasma reduction reaction and tested for photodegradation of methyl blue (MB) under sunlight exposure. The argon plasma born reactive species were used to reduce silver ions to AgNPs in the solution. Glucose, fructose and sucrose were also added in the solution to stabilize the growth process. The glucose stabilized reaction produced the smallest nanoparticles of 12 nm, while sucrose stabilized reaction produced relatively larger nanoparticles (14 nm). The nanoparticles exhibited rough morphology and narrow diameter distribution regardless of stabilizer type. The narrow diameter distribution and small band gap helped activating majority of nanoparticles at a single wavelength of light spectrum. The band gap energy of AgNPs varied from 2.22 eV to 2.41 eV, depending on the saccharide type. The photoluminescence spectroscopy of AgNPs produced emission peaks at 413 nm, 415 nm, and 418 nm. The photocatalytic potential of AgNP samples was checked by degrading MB dye under sunlight. The degradation reaction reached a saturation level of 98% after 60 min of light exposure.

Recent advances in structural modifications of photo-catalysts for organic pollutants degradation - A comprehensive review

Over the last few years, industrial and anthropogenic activities have increased the presence of organic pollutants such as dyes, herbicides, pesticides, analgesics, and antibiotics in the water that adversely affect human health and the environment worldwide. Photocatalytic treatment is considered a promising, economical, effective, and sustainable process that utilizes light energy to degrade the pollutants in water. However, certain drawbacks like rapid recombination and low migration capability of photogenerated electrons and holes have restricted the use of photo-catalysts in industries. Hence, despite the abundance of lab-scale research, the technology is still not much commercialized in the mainstream. Several structural modifications in the photo-catalysts have been adopted to enhance the pollutant degradation performance to overcome the same. In this context, the present review article outlines the different advanced heterostructures synthesized to date for improved degradation of three major organic pollutants: antibiotics, dyes, and pesticides. Moreover, the article also emphasizes the degradation kinetics of photo-catalysts and the publication trend in the past decade along with the roadblocks preventing the transfer of technology from the laboratory to industry and new age photo-catalysts for the profitable implications in industrial sectors.

Degradation of the residual textile mixture cetyltrimethylammonium bromide/remazol yellow gold RNL-150%/reactive blue BF-5G: evaluation photo-peroxidation and photo-Fenton processes in LED and UV-C photoreactors

This article presents a study on the degradation of a residual textile mixture composed of cationic surfactant cetyltrimethylammonium bromide (CTAB) and the remazol yellow gold RNL-150% and reactive blue BF-5G textile dyes. This was carried out by employing the photo-peroxidation and photo-Fenton processes in LED and UV-C photoreactors. The photo-Fenton process was the most efficient as regards the degradation of the CTAB and dye mixture, for both types of radiation. In the kinetic study, degradations of 99% were obtained in 180 min for the chromophore groups using both types of radiation. The degradation of the CTAB and aromatic groups was, meanwhile, an average of 25% when employing LED radiation. The behavior of the degradation reaction was pseudo-first-order. Toxicity tests indicated that the solutions were better able to grow seeds and bacteria after treatment with the photo-Fenton process, using both types of radiation. The photo-Fenton processes carried out by employing LED and UV-C photoreactors were able to degrade the CTAB and dye mixture, thus highlighting the efficiency of LED radiation when its power (three times smaller) is compared to that of UV-C radiation. This process, therefore, represents an alternative for use in textile wastewater treatment systems.

Independent hydrothermal synthesis of the undoped, nitrogen, boron and sulphur doped biogenic carbon nanodots and their potential application in the catalytic chemo-reduction of Alizarine yellow R azo dye

This research study highlights the catalytic usage of hetero atoms doped and undoped biogenic carbon nano dots (BCNDs) in the reduction of Alizarine yellow R (AYR) dye. Hydrothermal route was followed to synthesize the eco-friendly and fluorescent undoped as well as, N, B & S doped BCNDs from Syzygium cumini (S. cumini) fruit extract. Synthesized BCNDs exhibited good fluorescent and optical properties. From the HR-TEM results, the sizes of the spherically shaped undoped, N, B & S doped BCNDs were found to be 4.75 nm, 4.31 nm, 4.07 nm & 3.96 nm respectively. XRD results highlighted their amorphous nature. Functional groups and elemental percentages were elucidated from the results of FT-IR, EDS and XPS. Graphitic texture of the BCNDs were explained from Raman spectroscopy results and SAED. Thermal stability of BCNDs was evident from the results of TGA analysis. Further, BCNDs were used as green catalyst in the reduction of Alizarine Yellow R (AYR) dye. Langmuir- Hinshelwood mechanism was applied to evaluate the catalytic influence of BCNDs on AYR dye.

Environmentally friendly fabrication of new β-Cyclodextrin/ZrO2 nanocomposite for simultaneous removal of Pb(II) and BPA from water

Heavy metals and endocrine disrupters often co-exist in wastewater, while their possible competition behaviours make uptake removal more challenging. Therefore, β-Cyclodextrin based nanocomposite adsorbent was successfully fabricated (β-Cyclodextrin/ZrO₂) for the simultaneous uptake of Pb(II) and Bisphenol A from wastewater. FTIR, XRD, and XPS confirmed the successful fabrication of the β-Cyclodextrin/ZrO₂ nanocomposite. In this setting, oxygen-containing groups are primarily responsible for the Pb(II) binding, while the β-Cyclodextrin cavities adsorb Bisphenol A through host-guest interaction, enabling the simultaneous removal of Pb(II) and Bisphenol A. In the mono contaminant system, the nanocomposite displayed prominent removal ability toward Pb(II) and Bisphenol A with adsorption characteristics of pseudo-second-order, Langmuir, and Freundlich isotherm model. The maximum adsorption capacities were identified for Pb(II) and Bisphenol A to be 274.4 mg/g and 174.9 mg/g at 298 K, respectively. Most importantly, the β-Cyclodextrin/ZrO₂ could efficiently attain simultaneous removal of Pb(II) and Bisphenol A by avoiding their competitive behaviours was due to the different adsorption mechanisms (electrostatic interaction and host-guest interaction). Moreover, the adsorbed Pb(II) and Bisphenol A could be successfully recovered with a slight decline in nanocomposite removal performance even after 4 cycles in the binary-component system. All these findings provide insights into the fabrication of highly effective adsorbent with separated adsorption sites to treat wastewater bearing heavy metal and endocrine disrupters.

Recent progress in green and biopolymer based photocatalysts for the abatement of aquatic pollutants

Enormous research studies on the abatement of anthropogenic aquatic pollutants including organic dyes, pesticides, cosmetics, antibiotics and inorganic species by using varieties of semiconductor photocatalysts have been reported in recent decades. Besides, many of these photocatalysts suffer in real applications owing to their high production cost and low stability. In many cases, the photocatalysts themselves are being considered as secondary pollutants. To eliminate these drawbacks, the green synthesized photocatalysts and the use of biopolymers as photocatalyst supports are considered in recent years. In this context, recent developments in green synthesized metals, metal oxides, other metal compounds, and carbon based photocatalysts in water purification are critically reviewed. Furthermore, the pivotal role of biopolymers including chitin, chitosan, cellulose, natural gum, hydroxyapatite, alginate in photocatalytic removal of aquatic pollutants is comprehensively reviewed. The presence of functional groups, electron trapping ability, biocompatibility, natural occurrence, and low production cost are the major reasons for using biopolymers in photocatalysis. Finally, the summary and conclusion are presented along with existing challenges in this research area.

Degradation of textile dyes from aqueous solution using tea-polyphenol/Fe loaded waste silk fabrics as Fenton-like catalysts

In this study, waste silk fabrics (SF) were modified with tea-polyphenols (TPs) and then iron (Fe²⁺). The modified silk fabrics (TP-SF/Fe) were characterized via Fourier-transform infrared (FTIR), energy dispersive spectroscopy (EDS), scanning electron microscopy (SEM), and X-ray photoelectron spectroscopy (XPS) analysis. TP-SF/Fe was used in the Fenton-like removal of dyes (methylene blue, reactive orange GRN, and cationic violet X-5BLN) from aqueous solutions with catalyst-like activity. The effects of different catalyst samples, contact time, H₂O₂ concentration, initial dye concentration, and pH values on dye removal were investigated. The results showed that the dye removal percentages with the TP-SF/Fe-H₂O₂ sample reached 98%, 97%, and 95% in 5–40 min for methylene blue, reactive orange GRN, and cationic violet X-5BLN, respectively. Different thermodynamic and kinetic models were used to check the best fit of the adsorption data. The results indicated that the Freundlich isotherm and pseudo first-order kinetics models were the best fits. Moreover, it was also proved that TP-SF/Fe would be quite an effective and economical adsorbent for the treatment of textile dye wastewater. This work provides the basis for waste silk application in the removal of dyes from wastewater.

In this study, waste silk fabrics were modified with tea-polyphenols then loaded with Fe²⁺ for degradation of dyes.

Underwater microplasma bubbles for efficient and simultaneous degradation of mixed dye pollutants

Complete degradation of mixtures of organic pollutants is a major challenge due to their diverse degradation pathways. In this work, a novel microplasma bubble (MPB) reactor was developed to generate plasma discharges inside small forming bubbles as an effective mean of delivering reactive species for the degradation of the target organic contaminants. The results show that the integration of plasma and bubbles resulted in efficient degradation for all azo, heterocyclic, and cationic dyes, evidenced by the outstanding energy efficiency of 13.0, 18.1 and 22.1 g/kWh with 3 min of processing, in degrading alizarin yellow (AY), orange II (Orng-II) and methylene blue (MB), individually. The MPB treatment also effectively and simultaneously degraded the dyes in their mixtures such as AY + Orng-II, AY + MB and AY + Orng-II + MB. Scavenger assays revealed that the short-lived reactive species, including the hydroxyl (OH) and superoxide anion (O₂^-) radicals, played the dominant role in the degradation of the pollutants. Possible degradation pathways were proposed based on the intermediate products detected during the degradation process. The feasibility of this proposed strategy was further evaluated using other common water pollutants. Reduced toxicity was confirmed by the observed increases in human cell viability for the treated water. This work could support the future development of high performance- and energy-efficient wastewater abatement technologies.