Triclosan degradation by heterogeneous photocatalysis using ZnO immobilized in biopolymer as catalyst

Critical review on the environmental behaviors and toxicity of triclosan and its removal technologies

As a highly effective broad-spectrum antibacterial agent, triclosan (TCS) is widely used in personal care and medical disinfection products, resulting in its widespread occurrence in aquatic and terrestrial environments, and even in the human body. Notably, the use of TCS surged during the COVID-19 outbreak, leading to increasing environmental TCS pollution pressure. From the perspective of environmental health, it is essential to systematically understand the environmental occurrence and behavior of TCS, its toxicological effects on biota and humans, and technologies to remove TCS from the environment. This review comprehensively summarizes the current knowledge regarding the sources and behavior of TCS in surface water, groundwater, and soil systems, focusing on its toxicological effects on aquatic and terrestrial organisms. Effluent from wastewater treatment plants is the primary source of TCS in aquatic systems, whereas sewage application and/or wastewater irrigation are the major sources of TCS in soil. Human exposure pathways to TCS and associated adverse outcomes were also analyzed. Skin and oral mucosal absorption, and dietary intake are important TCS exposure pathways. Reducing or completely degrading TCS in the environment is important for alleviating environmental pollution and protecting public health. Therefore, this paper reviews the removal mechanisms, including adsorption, biotic and abiotic redox reactions, and the influencing factors. In addition, the advantages and disadvantages of the different techniques are compared, and development prospects are proposed. These findings provide a basis for the management and risk assessment of TCS and are beneficial for the application of treatment technology in TCS removal.

Tailoring CuOx loading on CoFe2O4 nanocubes photocatalyst for superior photocatalytic degradation of triclosan pollutants under VL irradiation and toxicological evaluation

In this study, we report the development of a novel CuOx(3 wt%)/CoFe2O4 nanocubes (NCs) photocatalyst through simple co-precipitation and wet impregnation methods for the efficient photocatalytic degradation of triclosan (TCS) pollutants. Initially, rod-shaped bare CoFe2O4 was synthesized using a simple co-precipitation technique. Subsequently, CuOx was loaded in various percentages (1, 2, and 3 wt%) onto the surface of bare CoFe2O4 nanorods (NRs) via the wet impregnation method. The synthesized materials were systematically characterized to evaluate their composition, structural and electrical characteristics. The CuOx(3 wt%)/CoFe2O4 NCs photocatalyst exhibited superior photocatalytic degradation efficiency of TCS (89.9%) compared to bare CoFe2O4 NRs (62.1 %), CuOx(1 wt%)/CoFe2O4 (80.1 %), CuOx(2 wt%)/CoFe2O4 (87.0 %) under visible light (VL) irradiation (λ ≥ 420 nm), respectively. This enhanced performance was attributed to the improved separation effectiveness of photogenerated electron (e-) and hole (h+) in CuOx(3 wt%)/CoFe2O4 NCs. Furthermore, the optimized CuOx(3 wt%)/CoFe2O4 NCs exhibited strong stability and reusability in TCS degradation, as demonstrated by three successive cycles. Genetic screening on Caenorhabditis elegans showed that CuOx(3 wt%)/CoFe2O4 NCs reduced ROS-induced oxidative stress during TCS photocatalytic degradation. ROS levels decreased at 30, 60, and 120-min intervals during TCS degradation, accompanied by improved egg hatching rates. Additionally, expression levels of stress-responsible antioxidant proteins like SOD-3GFP and HSP-16.2GFP were significantly normalized. This study demonstrates the efficiency of CuOx(3 wt%)/CoFe2O4 NCs in degrading TCS pollutants, offers insights into toxicity dynamics, and recommends its use for future environmental remediation.

Occurrence of per- and polyfluoroalkyl substances in aquatic environments and their removal by advanced oxidation processes

Per- and polyfluoroalkyl substances (PFAS), one of the main categories of emerging contaminants, are a family of fluorinated organic compounds of anthropogenic origin. PFAS can endanger the environment and human health because of their wide application in industries, long-term persistence, unique properties, and bioaccumulation potential. This study sought to explain the accumulation of different PFAS in water bodies. In aquatic environments, PFAS concentrations range extensively from <0.03 (groundwater; Melbourne, Australia) to 51,000 ng/L (Groundwater, Sweden). Additionally, bioaccumulation of PFAS in fish and water biota has been stated to range from 0.2 (Burbot, Lake Vättern, Sweden) to 13,900 ng/g (Bluegill samples, U.S.). Recently, studies have focused on PFAS removal from aqueous solutions; one promising technique is advanced oxidation processes (AOPs), including microwaves, ultrasound, ozonation, photocatalysis, UV, electrochemical oxidation, the Fenton process, and hydrogen peroxide-based and sulfate radical-based systems. The removal efficiency of PFAS ranges from 3% (for MW) to 100% for UV/sulfate radical as a hybrid reactor. Therefore, a hybrid reactor can be used to efficiently degrade and remove PFAS. Developing novel, efficient, cost-effective, and sustainable AOPs for PFAS degradation in water treatment systems is a critical area of research.

Trimesic acid-functionalized chitosan: A novel and efficient multifunctional organocatalyst for green synthesis of polyhydroquinolines and acridinediones under mild conditions

Trimesic acid-functionalized chitosan (Cs/ECH-TMA) material was prepared through a simple procedure by using inexpensive and commercially available chitosan (Cs), epichlorohydrin (ECH) linker and trimesic acid (TMA). The obtained bio-based Cs/ECH-TMA material was characterized using energy-dispersive X-ray (EDX) and Fourier-transform infrared (FTIR) spectroscopy, field emission scanning electron microscopy (FESEM) and X-ray diffraction (XRD) analysis. The Cs/ECH-TMA material was successfully used, as a multifunctional heterogeneous and sustainable catalyst, for efficient and expeditious synthesis of medicinally important polyhydroquinoline (PHQ) and polyhydroacridinedione (PHA) scaffolds through the Hantzsch condensation in a one-pot reaction. Indeed, the heterogeneous Cs/ECH-TMA material can be considered as a synergistic multifunctional organocatalyst due to the presence of a large number of acidic active sites in its structure as well as hydrophilicity. Both PHQs and PHAs were synthesized in the presence of biodegradable heterogeneous Cs/ECH-TMA catalytic system from their corresponding substrates in EtOH under reflux conditions and high to quantitative yields. The Cs/ECH-TMA catalyst is recyclable and can be reused at least four times without significant loss of its catalytic activity.

Design of hydrotalcite and biopolymers entrapped tunable cerium organic cubic hybrid material for superior fluoride adsorption

The excess fluoride in drinking water is serious risk which leads to fluorosis. The adsorption method is facile route for defluoridation studies. Hybrid adsorbent possesses unique advantages like high surface area and high stability has been employed for water treatment. In the present work, hydrotalcite (HT) fabricated Ce-metal organic frameworks (MOFs) bridged with biopolymers (alginate and chitosan) namely HT-CeMOFs@Alg-CS cubic hybrid beads was developed and employed towards fluoride removal in batch mode. The fabricated HT-CeMOFs@Alg-CS beads were analyzed by DTA, FTIR, SEM, EDAX, TGA and XRD studies. Besides, FTIR and EDAX proved the affinity of HT-CeMOFs@Alg-CS cubic hybrid beads on fluoride was majorly attributed by electrostatic interaction, ion-exchange and complexation mechanism. To include detail insight into adsorption route; the kinetics, thermodynamic and isotherm studies were investigated for fluoride adsorption. The equilibrium data of HT-CeMOFs@Alg-CS cubic hybrid beads for fluoride adsorption was fitted with Langmuir isotherm model. Thermodynamic investigation results demonstrated that the fluoride adsorption was spontaneous with endothermic nature. The regeneration and field investigation results revealed that the developed HT-CeMOFs@Alg-CS cubic hybrid beads are reusable and more apt at field environment.

Novel assembly of BiVO4@N-Biochar nanocomposite for efficient detoxification of triclosan

The wide spread of antibacterial and antifungal agents demands in growing multifunctional materials to completely eliminate these organic contaminants in water. BiVO₄ (Bismuth vanadate) is a superior catalyst under visible light but suffers with high photoelectron-hole pair recombination rate and poor adsorption capacity which limits its efficiency. Addition of N-doped Biochar (N-Biochar) to BiVO₄ with large specific surface area and high conductivity are anticipated to overcome the problem and promote the catalytic performance. Thus, the present study developed a simple hydrothermal method to prepare BiVO₄@N-Biochar catalyst for efficient detoxification of Triclosan (TCS). The morphological analysis results suggested that BiVO₄ particles were evenly distributed on carbon surface amongst the N-Biochar matrix. Within 60 min of visible light irradiation, nearly 94.6% TCS degradation efficiency was attained by BiVO₄@N-Biochar (k = 0.02154 min^-1) while only 56.7% was attained with pure BiVO₄ (k = 0.00637 min^-1). In addition, LC-MS/MS technique was utilized to determine the TCS degradation products generation in the photodegradation process and pathway was proposed. Furthermore, the E. coli (Escherichia coli) colony forming unit assay was used to determine the biotoxicity of the degradation products in which 72.3 ± 2.6% of detoxification efficiency was achieved and suggested a substantial reduction in biotoxicity during the photodegradation.

Facile Synthesis of ZnO-CeO2 Heterojunction by Mixture Design and Its Application in Triclosan Degradation: Effect of Urea

In this study, simplex centroid mixture design was employed to determine the effect of urea on ZnO-CeO. The heterojunction materials were synthesized using a solid-state combustion method, and the physicochemical properties were evaluated using X-ray diffraction, nitrogen adsorption/desorption, and UV–Vis spectroscopy. Photocatalytic activity was determined by a triclosan degradation reaction under UV irradiation. According to the results, the crystal size of zinc oxide decreases in the presence of urea, whereas a reverse effect was observed for cerium oxide. A similar trend was observed for ternary samples, i.e., the higher the proportion of urea, the larger the crystallite cerium size. In brief, urea facilitated the co-existence of crystallites of CeO and ZnO. On the other hand, UV spectra indicate that urea shifts the absorption edge to a longer wavelength. Studies of the photocatalytic activity of TCS degradation show that the increase in the proportion of urea favorably influenced the percentage of mineralization.

Fabrication of Ag3PO4/polyaniline-activated biochar photocatalyst for efficient triclosan degradation process and toxicity assessment

Triclosan (TCS) is a typical environmental pollutant, which seriously threatens the health of humans and organisms. A novel strategy of biochar/Ag₃PO₄/polyaniline (PANI) composite photocatalyst was synthesized by a facile chemical precipitation method to efficiently degrade TCS. XRD, Raman, ESR, etc. were used to reveal the effective associations among physiochemistry, photochemistry and photocatalytic properties of the composite. It was proved the synergistic effects of biochar (T-Bio) and PANI resulted in the decrease of Ag₃PO₄ particle size, the enhancement of adsorption, the improvement of light utilization, the increase of photogenerated carrier separation and the promotion of reactive species. The photocatalytic mechanism showed h⁺ was the main active species, O₂^- and OH played minor roles. Under the irradiation of visible light, the optimal photocatalyst (1.0% T-Bio/AP/1.0% PANI) displayed excellent photocatalytic activity with the removal rate of 85.21% for TCS within 10 min, and the apparent rate constant K' was 2.38 times of Ag₃PO₄. 11 main intermediates for TCS degradation were identified, and their toxicity was significantly reduced. The possible degradation pathways were proposed. This work is the first systematic study on the degradation behavior of TCS by Ag₃PO₄-based photocatalyst, and it provides a new approach to fabricate photocatalysts with synergistic effects and amazing photocatalytic activity by biochar.

Functioned catalysts with magnetic core applied in ibuprofen degradation

In the present work, the performance of Ag/ZnO/CoFe₂O₄ magnetic photocatalysts in the photocatalytic degradation of ibuprofen (IBP) was evaluated. This study considered the use of pure Ag/ZnO (5% Ag) and also the use of the Ag/ZnO/CoFe₂O₄ magnetic catalysts containing different amounts (5, 10 and 15% wt) of cobalt ferrite (CoFe₂O₄). The catalysts were characterized by scanning electron microscopy (SEM), X-ray diffraction (XRD) and photoacoustic spectroscopy. To carry out the photocatalytic degradation reaction, different concentrations of the ibuprofen contaminant solution (10, 20 and 30 ppm) and different concentrations of photocatalyst were tested (0.3 g L^-1, 0.5 g L^-1 and 1.0 g L^-1). The reaction parameters studied were: IBP concentration, catalyst concentration, adsorption and photolysis, influence of the matrix, radiation source (solar and artificial) and the effect of organic additive. At the end of the photocatalytic tests, the best operating conditions were defined. Considering the obtained results of degradation efficiency and magnetic separation, the optimal parameters selected to proceed with the other tests of the study were: ibuprofen solution concentration 10 ppm, Ag/ZnO/CoFe₂O₄ (5%) catalyst at a concentration of 0.3 g L^-1 and pH 4.5 of the reaction medium. The results indicated the feasibility of magnetic separation of the synthesized catalysts. A long duration test indicated that the catalyst exhibits stability throughout the degradation reaction, as more than 80% of IBP was degraded after 300 minutes. The photocatalytic activity was directly affected by the ferrite load. The higher the nominal load of ferrite, the lower the performance in IBP degradation. It was also observed that the smallest amount of ferrite studied was enough for the catalyst to be recovered and reused. The adsorption and photolysis tests did not show significant results in the IBP degradation. In addition, it was possible to verify that the aqueous matrix, the use of solar radiation and the addition of additive (acid formic) were interfered directly in the process. The catalyst reuse tests indicated that it can be recovered and reused at least three times without considerable catalytic activity loss.

Polymer-based immobilized Fe2O3-TiO2/PVP catalyst preparation method and the degradation of triclosan in treated greywater effluent by solar photocatalysis

The present study involves a novel protocol to develop a ternary composite catalyst for an effective post-treatment technique for greywater. The ternary film of Fe₂O₃-TiO₂/polyvinyl pyrrolidine (PVP) is coated on a glass tube using spray coating with annealing at 320 °C. The structure, thermal, microstructure, and surface properties of the coated film are characterized by X-ray diffraction (XRD), Fourier Transform Infrared Spectroscopy (FTIR), Field Emission Scanning Electron Microscopy (FESEM), and Thermo Gravimetric Analysis (TGA). The scratch hardness of photocatalysts at different Fe₂O₃/TiO₂ compositions is investigated based on the width measurement of scratch using FESEM analysis. Results show that at an optimum coating of 5% of Fe₂O₃/TiO₂ composition catalytic film, the maximum scratch hardness (7.984 GPa) is obtained. Also, the photocatalyst has the highest cohesive bond strength and wearing resistance. The degradation of triclosan (TCS) in treated greywater, discharged from the anaerobic-aerobic treatment system, is investigated at a lab-scale using a solar photocatalytic reactor. The response surface analysis has been performed from the different sets of experimental trials for various optimal parameters. It is observed that the TCS degradation efficiency of 83.27% has resulted under optimum conditions.

Green synthesis of lignin nanorods/g-C3N4 nanocomposite materials for efficient photocatalytic degradation of triclosan in environmental water

Triclosan (TCS) is a common anti-microbial ingredient in pharmaceutical and personal care products. The usage of TCS was banned by the United States Food and Drug Administration (in 2016) due to its potential health risks. However, TCS has been frequently detected in the aquatic environment. Therefore, it is vital to design low-cost and highly efficient photocatalysts to enhance TCS's photocatalytic degradation in wastewater treatment to eliminate its toxicity to environmental health. In this study, we developed a highly efficient catalyst by incorporating lignin nanorods (LNRs) into graphitic carbon nitride (GCN) nanomaterials as green LNRs/GCN-based nanocomposite photocatalysts for the effective degradation of TCS in waters. LNRs/GCN nanosheets (NSs) and LNRs/GCN-NRs based nanocomposite materials were prepared using a simple wet-impregnation method. The surface morphology and optical properties of as-synthesized materials were well-characterized using FE-SEM, XRD, XPS, and UV-DRS. The photocatalyst (LNRs/GCN-NRs) material showed maximum TCS degradation efficiency of 99.9% and a high rate constant of 0.0661 min^-1 under pH-10 with crucial reactive spices (OH and O₂^-), and excellent cycling performance (over five cycles) within 90 min of UV-light illumination. LNRs/GCN-NRs nanocomposite indicated enhanced photocatalytic performances for TCS degradation due to its strong synergistic effect between LNRs and GCN-NRs as bifunctional catalyst substrate morphology with efficient bandgap energy and accessible active sites compared to LNRs/GCN-NSs. Therefore, LNRs/GCN-NRs nanocomposite was observed to be a highly-active, low-cost, stable, eco-friendly, and efficient photocatalyst for complete degradation of TCS under UV-light irradiation.

Continuous process applied to degradation of triclosan and 2.8-dichlorodibenzene-p-dioxin

This study describes the use of a prototype for the continuous photocatalytic reaction process using Fe/Nb₂O₅-immobilized catalyst for triclosan and 2.8-dichlorodibenzene-p-dioxin (2.8-DCDD)'s degradation. The experiments were carried out with different parameters and matrices in a steady state. In addition, photolysis and photocatalytic tests were performed. The results indicated that the generation of 2.8-DCDD was observed in matrices with Cl^-. The Fe/Nb₂O₅-immobilized catalysts were efficient in the degradation of triclosan and 2.8-dichlorodibenzene-p-dioxin. However, 2.8-DCDD formation was not observed in the ultra-pure water matrix, which indicated influence of ions. The photocatalysis was more efficient than the photolysis when comparing both matrices and radiation. Even with a radiation oscillation, the solar process showed positive results.

Investigating the effect of hydrogen peroxide as an electron acceptor in increasing the capability of slurry photocatalytic process in dye removal

The hydrogen peroxide role in photocatalytic degradation of an anionic azo dye, Acid Orange 7 (AO7), was investigated in a slurry reactor. Commercial ZnO nanoparticles with an average size between 10 to 30 nm were used as catalysts. Optimum conditions for different parameters, including dye concentration (10-100 mg/L), catalyst concentration (0.1-0.5 g/L), and pH (5-10), were determined first in the absence of H₂O₂. Changes in the COD were measured for the optimum condition. The impact of adding hydrogen peroxide at different concentrations to the system operating at optimum conditions was investigated. It was observed that 0.416 mM hydrogen peroxide increased the system's efficiency and decreased reaction time by 40 min. The reaction followed first-order kinetic. Hydrogen peroxide alone did not contribute to oxidizing the contaminant, and its positive impact was attributed to decreasing electron-hole recombination in the photocatalytic process. Not only can the hydrogen peroxide-assisted photocatalytic process decrease retention time in treatment units, but it can also result in more contaminant degradation. Therefore, it can reduce the treatment cost.

Synthesis and characterization of Ag0(NPs)/TiO2 nanocomposite: insight studies of triclosan removal from aqueous solutions

Nanocomposite mesoporous Ag⁰(NPs)/TiO₂ thin film materials were synthesized and assessed for its efficient application in the elimination of potentially important drug triclosan from aqueous solutions. A template synthesis using the polyethylene glycol was enabled to obtain Ag⁰(NPs)/TiO₂ nanocomposite materials where zerovalent Ag was in situ doped to the titania network. The nanocomposite materials were characterized by the scanning electron microscope (SEM), energy dispersive X-ray spectroscopy (EDX), transmission electron microscope (TEM), EDX elemental mapping, X-ray diffraction (XRD) analyses and Brunauer-Emmett-Teller (BET) methods. Further, the diffuse reflectance spectroscopy (DRS) was introduced to estimate the band gap of these solids. The thin film materials were subjected to the remediation of water contaminated with triclosan using the UV-A light. The oxidative elimination of triclosan was demonstrated as a function of pH, concentration of triclosan and presence of several co-existing ions. Increase in pH (4.0-10.0) and triclosan concentrations (0.5-15.0 mg/L) had decreased significantly the percentage degradation of triclosan. The pseudo-first-order kinetics was shown in the degradation of triclosan and rate constant was significantly decreased with the increase in pollutant concentration (0.5-15.0 mg/L) and pH (4.0-10.0). The 1000 times presence of scavengers showed that ^•OH were, predominantly, caused the oxidation of triclosan. Moreover, multiple application of nanocomposite Ag⁰(NPs)/TiO₂(B) revealed that the thin film was fairly intact since the photocatalytic efficiency of triclosan removal was almost unaffected.

Photocatalysis for Organic Wastewater Treatment: From the Basis to Current Challenges for Society

Organic pollutants such as dyes, antibiotics, analgesics, herbicides, pesticides, and stimulants become major sources of water pollution. Several treatments such as absorptions, coagulation, filtration, and oxidations were introduced and experimentally carried out to overcome these problems. Nowadays, an advanced technique by photocatalytic degradation attracts the attention of most researchers due to its interesting and promising mechanism that allows spontaneous and non-spontaneous reactions as they utilized light energy to initiate the reaction. However, only a few numbers of photocatalysts reported were able to completely degrade organic pollutants. In the past decade, the number of preparation techniques of photocatalyst such as doping, morphology manipulation, metal loading, and coupling heterojunction were studied and tested. Thus, in this paper, we reviewed details on the fundamentals, common photocatalyst preparation for coupling heterojunction, morphological effect, and photocatalyst’s characterization techniques. The important variables such as catalyst dosage, pH, and initial concentration of sample pollution, irradiation time by light, temperature system, durability, and stability of the catalyst that potentially affect the efficiency of the process were also discussed. Overall, this paper offers an in-depth perspective of photocatalytic degradation of sample pollutions and its future direction.

Critical review on the mechanistic photolytic and photocatalytic degradation of triclosan

The environmentally extended presence of triclosan, TCS, component of many pharmaceutical and personal care products, and its known persistent character have awoke the scientific and social concern leading to the study of effective remediation techniques. Advanced oxidation techniques stand out for the effectiveness in degrading many persistent compounds, and as a result, they have been addressed by many researchers. However, the powerful oxidation media might lead to the formation of undesirable by-products, concern that has also been widely addressed. With regard to the presence of TCS, photolytic and photocatalytic processes provide a very effective degradation yield and rate, with a large number of reports addressing its removal from different environmental matrices. But currently, there is no clear understanding of the mechanisms involved and the routes responsible for the formation of degradation products. Thus, this work presents an exhaustive and critical analysis of the state of the art related to the photo-degradation of TCS, with special focus on the formation of oxidation by-products, on the phenomena responsible and on the influence of operation variables. This report aims at offering valuable information to researchers dealing with this environmentally relevant problem.

Bi2Fe4O9 in pellet form is an alternative in the wastewater treatment process

This study aimed to synthesize Bi₂Fe₄O₉ and apply it to the degradation of tartrazine yellow dye. Bi₂Fe₄O₉ was synthesized using the solid-state reaction and the Pechini method. The materials obtained were characterized using X-ray diffraction (XRD), visible ultraviolet spectroscopy (UV-Vis) and field emission scanning electron microscopy (FEG). The microscopic images revealed a morphological difference between the two materials in which the material obtained by the Pechini method is the most porous and have the largest surface area. The pellet obtained by the Pechini method was seen to have a lower bandgap value when compared with the sample solid state reaction. In the photocatalysis tests, the best performance was also that of the material obtained by the Pechini method, with 99.34% degradation, while the material obtained by solid state reaction showed 85.86% in 120 minutes. The solution degraded with the material obtained by the Pechini method presented 81.66% of mineralization while the solution with the material obtained by solid state reaction showed 60.97% of mineralization. The results confirmed that the material obtained by both syntheses is able to maintain its effectiveness after 10 repetitions of the photocatalytic process, proving to be promising for waste treatment in the industrial field.

Three-dimensional microspheric g-C3N4 coupled by Broussonetia papyrifera biochar: facile sodium alginate immobilization and excellent photocatalytic Cr(iv) reduction

g-C₃N₄–Broussonetia papyrifera biochar–sodium alginate composites were prepared. Composite recyclability and activity for photocatalytic Cr(vi) reduction and the origin of enhanced photocatalytic activity relative to that of g-C₃N₄ were probed.

Enhanced Photocatalytic Activity of Semiconductor Nanocomposites Doped with Ag Nanoclusters Under UV and Visible Light

Emerging contaminants (ECs) represent a wide range of compounds, whose complete elimination from wastewaters by conventional methods is not always guaranteed, posing human and environmental risks. Advanced oxidation processes (AOPs), based on the generation of highly oxidizing species, lead to the degradation of these ECs. In this context, TiO2 and ZnO are the most widely used inorganic photocatalysts, mainly due to their low cost and wide availability. The addition of small amounts of nanoclusters may imply enhanced light absorption and an attenuation effect on the recombination rate of electron/hole pairs, resulting in improved photocatalytic activity. In this work, we propose the use of silver nanoclusters deposited on ZnO nanoparticles (ZnO–Ag), with a view to evaluating their catalytic activity under both ultraviolet A (UVA) and visible light, in order to reduce energetic requirements in prospective applications on a larger scale. The catalysts were produced and then characterized by scanning electron microscopy (SEM), X-ray diffractometry (XRD) and inductively coupled plasma-optical emission spectrometry (ICP-OES). As proof of concept of the capacity of photocatalysts doped with nanoclusters, experiments were carried out to remove the azo dye Orange II (OII). The results demonstrated the high photocatalytic efficiency achieved thanks to the incorporation of nanoclusters, especially evident in the experiments performed under white light.

The synthesis of CB[8]/ZnO composites materials with enhanced photocatalytic activities

Enhancing the separation of hole-electron pairs is one of the valid pathway to enhance the photocatalytic degradation performance of semiconductors. In this work, cucurbit[8]uril/zinc oxide (CB[8]/ZnO) composites were prepared. The structure, morphology, surface elements and optical properties of the composite are characterized by powder X-ray diffraction, scanning electron microscopy, Fourier transform infrared spectroscopy, X-ray photoemission spectroscopy, thermogravimetric analysis, and specific surface area measurements. In the photocatalytic degradation of 500 mg/L reactive brilliant red X-3B and 400 mg/L reactive yellow X-RG solutions, the rate constant of the CB[8]/ZnO composite is six times that of pure ZnO. A possible photocatalytic degradation mechanism is proposed. Zn²⁺ ions chelate with the carbonyl group of CB[8] on the surface of CB[8]/ZnO. Under ultraviolet-visible light irradiation, the generated holes of ZnO are transferred to and trapped on the CB[8] units to facilitate the separation of electron-hole pairs, improving the photocatalytic performance of this system.

Synthesis of Ag/BiVO4/rGO composite with enhanced photocatalytic degradation of triclosan

A ternary visible-light driven photocatalyst, Ag/BiVO₄/reduced graphene oxide (rGO) composite was manufactured by hydrothermal strategy. The optimized products were characterized by XRD, SEM, HRTEM, EDS, XPS, DRS, Raman spectra, PL, BET, photocurrent density and EIS analysis. Compared to pure BiVO₄, the fabricated ternary composite showed enhanced photocatalytic ability to decompose pollutant under visible light. Triclosan was completely removed after 100 min in solution with 1 mg/mL photocatalyst under visible light irradiation. Repeated cycle tests demonstrated the photo-stability and reusability of composite to decompose triclosan, indicating that this material could be utilized repeatedly. The upgraded photocatalytic ability was attributed to the addition of Ag and rGO, which enhanced the charge separation and inhibited the recombination of photogenerated electrons and holes. The EPR spin-trap technique (with DMPO) was performed to identify the radicals produced in Ag/BiVO₄/rGO under the visible light, and trapping experiments were conducted to determine the main active species in the photocatalytic process of decomposing triclosan. Finally, seven reaction intermediates of triclosan were detected by LC-MS/MS and possible degradation routes were proposed.

PCDD/Fs traceability during triclosan electrochemical oxidation

5-Chloro-2-(2,4-dichlorophenoxy)phenol (TCS) is a persistent organic pollutant (POP) widely used in different consumer goods. Its recalcitrant nature demands the application of effective remediation technologies in order to avoid the negative environmental impact associated to the discharge of contaminated waters. Although advanced oxidation technologies have been considered the best alternative to destroy bio-recalcitrant compounds, the likely formation of high toxicity byproducts must be analysed before large-scale deployment. In this work, we aim to trace the presence of chlorinated compounds during the electro-oxidation of aqueous TCS samples. First, we analyze the influence of the initial concentration of TCS on the toxicity of the oxidation medium expressed by the International-Toxicity Equivalency Factor (I-TEF); second, we have detected the formation of intermediate organo-chlorinated compounds by GC-MS supported by HPLC and finally, we have quantified the concentration of highly-polychlorinated dibenzo-p-dioxins and dibenzofurans (PCDD/Fs) by HRGC-HRMS within the oxidation treatment. In those samples where TCS had been completely degraded the concentration of PCDD/Fs showed a high increase, especially when NaCl was used as electrolyte, with the initial concentration of TCS. Under these conditions the I-TEF achieved values up to 3.8 × 10² pg L^-1.

Experimental Design and Optimization of Triclosan and 2.8-Diclorodibenzeno-p-dioxina Degradation by the Fe/Nb2O5/UV System

This study describes the experimental design and optimization of the photocatalytic reaction using the immobilized catalyst Fe/Nb2O5 in the degradation of Triclosan and 2.8-DCDD. The techniques employed to characterize the photocatalysts were: specific surface area, average pore volume, average pore diameter, photo-acoustic spectroscopy (PAS), X-ray diffraction (XRD), and scanning electron microscopy (SEM/EDS). The reaction parameters studied were pH, catalyst concentration, catalyst calcination temperature, and nominal metallic charge. The results indicated that the immobilized Fe/Nb2O5 catalysts were efficient in the degradation of Triclosan and 2.8-dichlorodibenzene-p-dioxin. The catalysts with nominal metal loading of 1.5% Fe calcined at 873 K showed the highest constant reaction rate and the lowest half-life 0.069 min−1 and 10.04 min. Tests in different matrices indicated that the photocatalytic reaction using aqueous solution containing Cl− is faster when compared with the ultrapure water matrix.

Isolation and identification of Pseudomonas from wastewater, its immobilization in cellulose biopolymer and performance in degrading Triclosan

Triclosan (TCS) is a well-known emerging contaminant got wide use in daily use products of domestic purpose, which provides the way to enter the ecological cycle, and is preferably detected in sewage treatment plants. In this study, TCS degrading bacteria (TDB) was isolated and identified from a wastewater treatment plant at the National Institute of Technology-Karnataka, Surathkal (NITK), India. The isolate was reported as Pseudomonas strain by performing 16S RNA Sequencing using BLAST analysis. Bacterial growth depends upon several environmental factors. Hence its growth optimization was carried out by response surface method (RSM) based central composite design (CCD) and validated by the artificial neural network (ANN). The Parameters or inputs used for optimization are pH, time (days), agitation (rpm) and sorbent dosage (μg/L). Experiments were conducted in batch mode to achieve optimum growth of bacteria based on RSM trial runs. The RSM model predictions were in better agreement with the experimental results and it was confirmed by ANN. The deviation lies within ±10% with experimental results compared to ANN for maximum trials. Hence optimized parameters were established and arrived at pH - 7, time - 13 days, agitation - 150 rpm, dosage - 1.5 μg/L presented 69% removal of TCS. Minimum inhibitory assay of isolated strain was conducted to identify the degradation capacity of TCS and it was found out to be lesser than 0.025 mg of TCS. Later the strain was immobilized in two different matrices. One is biopolymer extracted from cellulose (Water Hyacinth) along with sodium alginate and second is free bacteria with sodium alginate and was made in the form of beads. The removal of TCS by TDB-cellulose-alginate (BCA) and TDB-Alginate (BA) beads were 58% and 30% respectively. Hence it was concluded that BCA beads showed effective removal compared to BA beads. Therefore, isolate can degrade TCS when the concentration ranges from 0.025 mg/L to 5.5 ng/L.

Applying analytical decision methods for determination of the best treatment alternative to remove emerging micropollutants from drinking water and wastewater: triclosan example

Increasing human activities have not only substantially altered the natural material cycle but also created new synthetic chemicals flows. Some of these chemicals, which are described as micropollutants (MPs), may result in adverse effects on human health, aquatic organisms, and ecosystems. MPs can be transported to the environment and water resources in a variety ways including domestic and industrial wastewater. Unfortunately, most MPs are only partially removed in existing conventional treatment plants. Therefore, conventional treatment plants should be modernized by advanced treatment technologies to protect the environment and human health. However, there are various mysteries about best treatment techniques, evaluation criteria, and decision-making methods. In this study, it was aimed to determine the best treatment alternatives for triclosan (TCS) which is one of the priority MPs. A total of 18 evaluation criteria were identified and prioritized by employing analytical hierarchy process (AHP) and entropy methods. Treatment alternatives were identified and their performance was assessed through a comprehensive literature investigation. In decision-making processes of determining these alternatives, "technique for order preference by similarity to ideal solution (TOPSIS)," "preference ranking organization method for enrichment evaluation (PROMETHEE)," and "Višekriterijumsko kompromisno rangiranje (VIKOR)" analytical decision-making methods were employed, and priority rankings were determined according to each decision method. The final priority ranking was found as adsorption > membrane filtration > hybrid processes > advanced oxidation processes > constructed wetlands > conventional treatment processes > biological treatment > other treatment processes. Although the obtained results are specific to TCS, the employed analytical decision methods can be also used to decide the best treatment alternatives for other MPs.

Decomposition of Contaminants of Emerging Concern in Advanced Oxidation Processes

This paper compares the removal degrees of selected contaminants of emerging concern in water solutions during advanced oxidation processes (AOPs), such as H2O2, O3, UV, UV/TiO2, UV/H2O2, and UV/O3. The tested micropollutants belong to the following groups: pharmaceuticals, dyes, UV filters, hormones, pesticides, and food additives. The highest removal rate of pharmaceutical compounds was observed during the UV/TiO2 process. The decomposition of hormones in this process exceeded 96% and the concentration of the UV filter dioxybenzone was reduced by 75%. The pesticide triallat and the food additive butylated hydroxytoluene were most effectively oxidized by the UV process and their removal degrees exceeded 90%. The lowest removal degree in all examined processes was observed in the case of caffeine. Toxicological analysis conducted in post-processed water samples indicated the generation of several oxidation by-products with a high toxic potential. The presence of those compounds was confirmed by the GC-MS analysis. The performance of the UV/O3 process leads to the increase of the toxicity of post-processed water solutions, especially solutions containing degradation by-products of carbamazepine, diclofenac sodium salt, acridine, trialatte, triclosan, and β-estradiol were characterized by high toxicity.

Nanocomposite Au NP/TiO2 thin film in the efficient remediation of aqueous solutions contaminated with emerging micro-pollutants

The present communication specifically aims to synthesize novel nanocomposite material Au NPs/TiO₂ in a simple template process using the polyethylene glycol as filler media. The thin film of the nanocomposite material was characterized by the advanced analytical tools. The surface morphology was obtained by the scanning electron microscopic (SEM) and transmission electron microscopic (TEM) images of solids. Similarly, the surface topography and roughness of solid were obtained by the atomic force microscopic (AFM) image of thin film. X-ray diffraction (XRD) data enabled to confirm that the TiO₂ was predominantly present with its anatase phase. The specific surface area and pore size of the solid were obtained using the N₂ adsorption/desorption data. Nanocomposite Au NP/TiO₂ thin film was employed in the photocatalytic removal of sulfamethoxazole and triclosan from aqueous solutions using less harmful UV-A light (λ_max = 330 nm). Various physicochemical parametric studies enabled to deduce the mechanism involved in the degradation process. The degradation kinetics as a function of pH (pH 4.0-10.0) and micro-pollutant concentrations (0.5-15.0 mg/L) was extensively studied. The mineralization of these pollutants was obtained using the non-purgeable organic carbon (NPOC) data. The stability of thin film was assessed by the repeated operations, and presence of several co-existing ions simulates the studies to real matrix treatment. Further, the presence of scavengers enabled to pin point the radical-induced degradation of sulfamethoxazole and triclosan from aqueous solutions.

Nanomaterials for treating emerging contaminants in water by adsorption and photocatalysis: Systematic review and bibliometric analysis

Emerging contaminants in the aquatic environment have become a worldwide problem. Conventional wastewater treatment processes are ineffective for eliminating the emerging contaminants at trace concentrations. Nanomaterials possessing novel size-dependent properties, however, have shown great potential for removing these contaminants. Herein we reviewed nanomaterials reported for removing emerging contaminants by adsorption and/or photocatalysis, and their removal capacity, mechanism, and influencing factors are discussed. Meanwhile, a large-scale bibliometric analysis is conducted on the trends of the emerging contaminants, nanoadsorbents, nanophotocatalysts, and related research topics from the literature during 1998-2017.

Comparision of photocatalysis and photolysis processes for arsenic oxidation in water

The oxidation of As(III) to As(V) in aqueous solution was evaluated using heterogeneous photocatalysis and photolysis. The influence of TiO₂ as catalyst in different crystalline (rutile, anatase) and commercial forms was evaluated in a batch reactor and an insignificant difference was observed between them. The process by photocatalysis reached up to 97% As(III) oxidation and no significant difference was observed comparing to results obtained by photolysis. The photolysis experiments (UV radiation only), also carried out in a batch system, showed a high oxidation rate of As(III) (90% in 20min). The influence of different matrices (well water, river water and public water supply) were evaluated. Additionally, the effect of As(V) concentration, generated during the oxidation process, was studied. Continuous photolysis experiments using only UV radiation were performed, resulting in a high As(III) oxidation rate. Using a flow rate of 5mLmin^-1 and an initial concentration of As(III) 200µgL^-1, gave an oxidation percentage of As(III) of up to 72%, showing a simple and economical alternative to the oxidation step of As(III) to As(V) in the treatment of water contaminated with arsenic.