Preparation of hybrids of wood sawdust with 3-aminopropyl-triethoxysilane. Application as an adsorbent to remove Reactive Blue 4 dye from wastewater effluents

Removal of organic and inorganic effluents from wastewater by using degradation and adsorption properties of transition metal-doped nickel ferrite

Removal of water pollutants (methylene blue dye and heavy metals) was achieved by zinc/manganese-doped nickel ferrites (Ni1 - xMxFe2O4, where x = 0.00, 0.025, 0.10). Degradation of dye was achieved under natural solar light illumination. Degradation studies of dye were conducted under different parameters such as contact time-80 min, dye's concentration-5 mg/L, pH-7, and dosage of ferrites-15 mg. The adsorption of dye was studied using non-linear kinetics models (pseudo-first-order and pseudo-second-order) and isotherm models (Langmuir and Freundlich). The adsorption of dye followed pseudo-first-order kinetics (R2 = 0.99377) than second-order kinetics (R2 = 0.98063) and Langmuir isotherm model (R2 = 0.96095) than Freundlich model (R2 = 0.95962) with maximum adsorption efficiency of 29.62 mg/g. Doping of nickel ferrites caused an increase in the removal percentage of methylene blue dye (80 to 90%) and inorganic effluents (75 to 95% for lead and 47 to 82% for cadmium). In addition to this, band gap energy (2.43 to 3.26 eV) (UV-Vis spectroscopy), pore radius (65.2 to 74.8 A°), and specific surface area (16.45 to 27.95 m2/g) (BET analysis) were also increased. Generally, the results of the study revealed that synthesized nanoparticles can act as potential candidate for the removal of effluents from wastewater under optimum parameters along with recyclability, reusability, and separation under the influence of a magnetic field.

Synthesis of sustainable mesoporous sulfur-doped biobased carbon with superior performance sodium diclofenac removal: Kinetic, equilibrium, thermodynamic and mechanism

Over the last years, the strategy of employing inevitable organic waste and residue streams to produce valuable and greener materials for a wide range of applications has been proven an efficient and suitable approach. In this research, sulfur-doped porous biochar was produced through a single-step pyrolysis of birch waste tree in the presence of zinc chloride as chemical activator. The sulfur doping process led to a remarkable impact on the biochar structure. Moreover, it was shown that sulfur doping also had an important impact on sodium diclofenac (S-DCF) removal from aqueous solutions due to the introduction of S-functionalities on biochar surface. The adsorption experiments suggested that General and Liu models offered the best fit for the kinetic and equilibrium studies, respectively. The results showed that the kinetic was faster for the S-doped biochar while the maximum adsorption capacity values at 318 K were 564 mg g-1 (non-doped) and 693 mg g-1 (S-doped); highlighting the better affinity of S-doped biochar for the S-DCF molecule compared to non-doped biochar. The thermodynamic parameters (ΔH0, ΔS0, ΔG0) suggested that the S-DCF removal on both adsorbents was spontaneous, favourable, and endothermic.

Modified Buckwheat Husk as a Filler for Urea-Formaldehyde Resin in Plywood Production

The aim of the presented research was to determine the suitability of both non-modified and modified buckwheat husk (BH) as a filler for urea-formaldehyde adhesive in plywood production. The effect of two modification methods, acetylation and silanization, was investigated. Infrared spectroscopy outcomes confirmed that both acetylation and silanization of the filler had occurred. Based on the results, it was found that the introduction of BH had a significant effect on both the adhesive properties and the characteristics of the manufactured plywood. The application of non-modified husks led to a reduction in viscosity and an extension of the gelation time, and the produced plywood boards were characterized by reduced bonding quality and increased delamination. Modification of the husk surface by acetylation and silanization with 3-aminopropyltriethoxysilane contributed to the noticeable improvement in the resin properties. On the other hand, the improvement in plywood properties, consisting of the increase in bonding quality and reduced delamination, was observed only in the case of the silanized husk. Furthermore, the use of non-modified and acetylated husk did not significantly influence the formaldehyde emission. The reduction in the investigated emission of formaldehyde was observed only in the case of variants containing 15 and 20% of silanized buckwheat husk.

Polydopamine-functionalized electrospun poly(vinyl alcohol)/chitosan nanofibers for the removal and determination of Cu(II)

Environmentally friendly and recycled polydopamine-functionalized electrospun poly(vinyl alcohol)/chitosan nanofibers (PVA/CS/PDA) were prepared through a low-energy-consumption procedure. The PDA coating endows PVA/CS/PDA nanofibers with good water stability. The PVA/CS/PDA nanofibers have a fibrillar and porous structure that is favorable for Cu(II) to access the active sites of the nanofibers. The adsorption isotherm and kinetics data preferably conform to the Liu isotherm and pseudo-second-order kinetic models, respectively. The maximum adsorption capacity of Cu(II) ions by PVA/CS/PDA nanofibers from the Liu isotherm model is 326.5 mg g-1. The PVA/CS/PDA nanofibers exhibit higher adsorption capacity than some other reported adsorbents. The adsorption mechanism study demonstrates that the Cu(II) adsorption is mainly ascribed to the complexation of Cu(II) with the imino, amino, and hydroxy moieties in PVA/CS/PDA nanofibers. The nanofibers can be employed for 5 cycles without significantly deteriorating performance. More interestingly, a fluorometry method based on the oxidation mimic enzyme activity of Cu(II) was developed to detect low concentrations of Cu(II) using the nanofibers as an adsorbent to preconcentrate Cu(II). The limit of detection is 0.42 mg L-1. The successful removal and detection of Cu(II) in Pearl River and mineral water samples demonstrates the great potential of PVA/CS/PDA nanofibers to remediate Cu(II)-polluted water.

Comprehensive adsorption and spectroscopic studies on the interaction of magnetic biochar from black wattle sawdust with beta-blocker metoprolol

The rise of contaminants of emerging concern in water-resources due to human activities has driven research toward wastewater treatment, specifically adsorption. The utilization of woody biomass for biochar production in adsorption has shown promise due to its high availability. This study shows the preparation of magnetic biochars (MB) from waste black wattle sawdust, utilizing ZnCl2 and NiCl2 (proportions: 1:0.5:0.5 = MB-0.5 and 1:1:1 = MB-1) as activating and magnetic agents. Synthesized via microwave-assisted-pyrolysis, MB boasts a high surface area (up to 765 m2.g-1) and functional groups, enhancing metoprolol medicine adsorption. Nonlinear kinetic and isothermal models were tested; the Avrami fractional-order kinetic model and Liu's isothermal model provided the best fits for experimental data. Thermodynamics and spectroscopic studies revealed spontaneous and exothermic adsorption processes, with physisorption magnitude and dominance of hydrogen-bond and π-π-interactions. MB can be easily extracted from an aqueous medium using magnetic fields, while adsorption capacity could be regenerated through green solvent elution.

Employ a Clay@TMSPDETA hybrid material as an adsorbent to remove textile dyes from wastewater effluents

A grafting of N1-(3-trimethoxysilylpropyl)diethylenetriamine (TMSPDETA) on natural clay was carried out to obtain an organic-inorganic hybrid clay material that was applied as an adsorbent to the uptake of Reactive Blue 19 (RB-19) and Reactive Green 19 (RG-19) dyes from aqueous wastewaters. This research demonstrates the effect of TMSPDETA contents on amino-functionalized clay materials' hydrophobic/hydrophilic behavior. The resultant material was utilized to uptake reactive dyes in aqueous solutions. The clay@TMSPDETA hybrid material was characterized by isotherm of adsorption and desorption of nitrogen, FTIR, elemental analysis, TGA, pHpzc, total acidity, total basicity groups, and hydrophilic balance. The hybrid samples were more hydrophilic than the pristine clay for ratios from 0.1 up to 0.5 due to adding amino groups to the pristine clay. FTIR spectra suggest that TMSPDETA was grafted onto the clay. The hybrid material presents a surface area 2.17-fold (42.7 m2/g) lower than pristine clay (92.7 m2/g). The total volume of pores of hybrid material was 0.0822 cm3/g, and the pristine clay material was 0.127 cm3/g, corresponding to a diminution of the total pore volume (Vtot) of 1.54 times. The kinetic data followed the pseudo-second-order (PSO) model for RB-19 and RG-19 reactive dyes. The equilibrium data were better fitted to the Liu isotherm model, displaying a Qmax as 178.8 and 361.1 mg g-1 for RB-19 and RG-19, respectively, at 20.0 °C. The main mechanism of interactions of the reactive dyes with the hybrid clay is electrostatic interaction. The clay@TMSPDETA has a very good effect on treating synthetic dye-textile wastewater. The removal percentage of simulated wastewater was up to 97.67% and 88.34% using distilled water and plastic industry wastewater as the solvents, respectively. The clay@TMSPDETA-0.1 could be recycled up to 5 cycles of adsorption and desorption of both dyes, attaining recoveries of 98.42% (RB-19) and 98.32% (RG-19) using 0.1 M HCl + 10% ethanol.

Statistical analysis by using soft computing methods for seawater biodegradability using ZnO photocatalyst

Water quality plays a significant role as a key factor in water resource management. The photocatalytic method is widely used for the removal of recalcitrant pollutants present in seawater. Photocatalysis is a cost-effective technology, sustainable, and environmentally friendly treatment process. In the current approach, a batch reactor was utilized experimentally to study the degradation of contaminants present in seawater by utilizing ZnO as a photocatalyst under natural sunlight. The performance of the process was studied by measuring the percentage removal efficiencies of total organic carbon (TOC), chemical oxygen demand (COD), biological oxygen demand (BOD), and biodegradability with respect to photocatalyst dosage, reaction time and pH of the solution. Biodegradability is defined as the ratio of BOD to COD and this parameter significantly removes pollutants from seawater. The higher the biodegradability, the better the performance of the treatment technology. It also significantly reduces the fouling characteristics of seawater during the desalination process. According to experimental values, the maximum percentage removal efficiencies were found to be TOC = 45.6, COD = 65.4, BOD = 20.01% and biodegradability = 0.038 with respect to the initial values of the seawater sample. The response surface methodology based on Box Behnken design (RSM-BBD) and a predictive model based on the MATLAB adaptive neuro-fuzzy inference system (ANFIS) tool were employed for modeling, optimizing, and evaluating the effects of parameters. According to the RSM-BBD and ANFIS models, the determination coefficients were R² = 0.959 and R² = 0.99, respectively, which was very close to 1. The maximum percentage removal efficiencies according to the RSM-BBD design were found to be TOC = 40.3; COD = 61.9; BOD = 18.8% and BOD/COD = 0.0390, whereas for the ANFIS model, the maximum reduction were found to be TOC = 46.5; COD = 65.4; BOD = 20.4% and BOD/COD = 0.040. In process optimization, the ANFIS model was shown better prediction than RSM-BBD in the process's optimization.

Wood waste-based functionalized natural hydrochar for the effective removal of Ce(III) ions from aqueous solution

In this study, a sustainable and easily prepared hydrochar from wood waste was studied to adsorb and recover the rare earth element cerium (Ce(III)) from an aqueous solution. The results revealed that the hydrochar contains several surface functional groups (e.g., C-O, C = O, OH, COOH), which largely influenced its adsorption capacity. The effect of pH strongly influenced the Ce(III) removal, achieving its maximum removal efficiency at pH 6.0 and very low adsorption capacity under an acidic solution. The hydrochar proved to be highly efficient in Ce(III) adsorption reaching a maximum adsorption capacity of 327.9 mg g^-1 at 298 K. The kinetic and equilibrium process were better fitted by the general order and Liu isotherm model, respectively. Possible mechanisms of Ce(III) adsorption on the hydrochar structure could be explained by electrostatic interactions and chelation between surface functional groups and the Ce(III). Furthermore, the hydrochar exhibited an excellent regeneration capacity upon using 1 mol L^-1 of sulfuric acid (H₂SO₄) as eluent, and it was reused for three cycles without losing its adsorption performance. This research proposes a sustainable approach for developing an efficient adsorbent with excellent physicochemical and adsorption properties for Ce(III) removal.

The production of activated biochar using Calophyllum inophyllum waste biomass and use as an adsorbent for removal of diuron from the water in batch and fixed bed column

The Calophyllum inophyllum species annually produces a large volume of cylindrical fruits, which accumulate on the soil because they do not have nutritional value. This study sought to enable the use of this biomass by producing activated biochar with zinc chloride as an activating agent for further application as an adsorbent in batch and fixed bed columns. Different methodologies were used to characterize the precursor and the pyrolyzed material. Morphological changes were observed with the emergence of new spaces. The carbonaceous material had a surface area of 468 m² g^-1, D_p = 2.7 nm, and V_T = 3.155 × 10^-1 cm³ g^-1. Scientific and isothermal studies of the adsorption of the diuron were conducted at the natural pH of the solution and adsorbent dosage of 0.75 g L^-1. The kinetic curves showed a good fit to the Avrami fractional order model, with equilibrium reached after 150 min, regardless of the diuron concentration. The Liu heterogeneous surface model well represented the isothermal curves. By raising the temperature, adsorption was encouraged, and at 318 K, the Liu Q_max was reached at 250.1 mg g^-1. Based on the Liu equilibrium constant, the nonlinear van't Hoff equation was employed, and the ΔG° were < 0 from 298 to 328 K; the process was exothermic nature (ΔH⁰ = -46.40 kJ mol^-1). Finally, the carbonaceous adsorbent showed good removal performance (63.45%) compared to a mixture containing different herbicides used to control weeds. The stoichiometric column capacity (q_eq) was 13.30 and 16.61 mg g^-1 for concentrations of 100 and 200 mg L^-1, respectively. The length of the mass transfer zone was 5.326 cm (100 mg L^-1) and 4.946 cm (200 mg L^-1). This makes employing the leftover fruits of the Calophyllum inophyllum species as biomass for creating highly porous adsorbents a very effective and promising option.

Comparative study for removal of cationic and anionic dyes using alginate-based hydrogels filled with citric acid-sawdust/UiO-66-NH2 hybrid

Nowadays, a big challenge is developing a sustainable and effective method for removing contaminants like dyes from aqueous solutions. In this regard, Zr-based metal-organic framework (UiO-66-NH₂) and sawdust as the ideal adsorbents were used. Due to their low separation in adsorption processes, embedding into alginate and obtaining composite beads are suggested as a suitable strategy. The achieved Ca-alginate/citric acid (CA)-sawdust/UiO-66-NH₂ hydrogel beads were used to compare cationic and anionic dyes removal. This sorbent indicated an excellent selectivity for removing methylene blue versus methyl orange in a binary system. pH = 6, adsorbent amount = 80 mg, methylene blue concentration = 10 mg/L, and contact time = 420 min were achieved as optimal parameters on methylene blue adsorption with an adsorption capacity of about 26 mg/g. The removal process of methylene blue followed linear Freundlich isotherm and nonlinear pseudo-2nd-order kinetic models. The regeneration test demonstrated methylene blue removal efficiency higher than about 89 % after 9 cycles. According to the outcomes, methylene blue could be attached to the adsorbent surface through the electrostatic, hydrogen bonding, and π-π interactions of the aromatic rings. These results confirm the potential of Ca-alginate/CA-sawdust/UiO-66-NH₂ hydrogel beads as a selective bio-sorbent for cationic dye removal.

Mesoporous carbon material prepared from sewage sludge hydrochar using Pluronic F127 as template for efficient removal of phenolic compounds: Experimental study and mechanism interpretation via advanced statistical physics model

Mesoporous carbon material (MCM) with rich ether surface group was prepared from sewage sludge hydrochar using Pluronic F127 as template under pyrolysis activation, which provided an energy-efficient method to promote the resource utilization of sewage sludge as adsorbents for phenols removal from water. The MCM possessed high surface area (549 m²/g), abundant mesopores (average width 3.81 nm) and well-developed graphite structure. Acidic conditions and low temperatures favored the adsorption of phenolic compounds. The quick adsorption process of reaching over 85% of the capacity in the first 10 min and intraparticle diffusion as primary rate-limiting step were observed for all phenolic compounds. Advanced statistical physics analysis was used successfully to interpret the adsorption mechanism of phenols onto MCM and revealed a multi-molecular monolayer adsorption process primarily through negative charge-assisted hydrogen bond interaction where the ether functional group contributed to the predominant active sites. The adsorption capacity of phenolic compounds depended upon the number of molecules adsorbed per ether active site and the available density of ether bond group on the surface of MCM. 2,4,6-trichlorophenol showed a highest adsorption priority to occupy the limited ether active sites and its adsorption capacity reached 0.49 mmol/g, while p-nitrophenol exhibited a maximum number of molecules adsorbed on the single ether active site, showing an adsorption capacity of 0.42 mmol/g. The synergistic effect of multi-interactions mechanisms resulted in phenolic compounds removal with adsorption energies lower than 30 kJ/mol. This prepared MCM adsorbent is promising for application in treatment of water polluted by phenols.

Powdered and beaded sawdust materials modified iron (III) oxide-hydroxide for adsorption of lead (II) ion and reactive blue 4 dye

The problems of lead and reactive blue 4 (RB4) dye contamination in wastewater are concerns because of their toxicities to aquatic life and water quality, so lead and RB4 dye removals are recommended to remove from wastewater before discharging. Sawdust powder (SP), sawdust powder doped iron (III) oxide-hydroxide (SPF), sawdust beads (SPB), and sawdust powder doped iron (III) oxide-hydroxide beads (SPFB) were synthesized and characterized with various techniques, and their lead or RB4 dye removal efficiencies were investigated by batch experiments, adsorption isotherms, kinetics, and desorption experiments. SPFB demonstrated higher specific surface area (11.020 m² g^-1) and smaller pore size (3.937 nm) than other materials. SP and SPF were irregular shapes with heterogeneous structures whereas SPB and SPFB had spherical shapes with coarse surfaces. Calcium (Ca) and oxygen (O) were found in all materials whereas iron (Fe) was only found in SPF and SPFB. O-H, C-H, C=C, and C-O were detected in all materials. Their lead removal efficiencies of all materials were higher than 82%, and RB4 dye removal efficiencies of SPB and SPFB were higher than 87%. Therefore, adding iron (III) oxide-hydroxide and changing material form helped to improve material efficiencies for lead or RB4 dye adsorption. SP and SPB corresponded to Langmuir model related to a physical adsorption process whereas SPF and SPFB corresponded to the Freundlich model correlated to a chemisorption process. All materials corresponded to a pseudo-second-order kinetic model relating to the chemical adsorption process. All materials could be reused more than 5 cycles with high lead removal of 63%, and SPB and SPFB also could be reused more than 5 cycles for high RB4 dye removal of 72%. Therefore, SPFB was a potential material to apply for lead or RB4 dye removal in industrial applications.

Egg-derived porous plasma modified clay composite for wastewater remediation

Clays are often envisaged as an alternative to activated carbon for wastewater pollutant adsorption. However, conclusive results have only been obtained for clays heavily chemically modified. In this study, a greener approach is proposed to improve the retention capacity of clays. It consists in mixing clay (C) with eggshell (ES) and calcine, and then exposing to gliding arc plasma (ESC-800/PL). The resulting materials were characterized by nitrogen physisorption, FTIR, XRD, TGA/DTG, and point of zero charge analyses. The preparation gives porous platelet agglomerates resulting from the kaolinite-metakaolinite transition, thereby increasing their internal specific surface area and capacity to retain pollutants. This granular distribution is kept stable by partial pozzolanic reactions avoiding deagglomeration. The specific surface area and total pore volume increased respectively from 14 m² g^-1 and 0.049 cm³ g^-1 to 89 m² g^-1 and 0.061 cm³ g^-1 leading to an enhanced removal efficiency of Fast Green and Orange G dyes from polluted water. The maximum adsorption capacity occurred at 298 K attaining values of 32.34 and 14.78 mg g^-1 for OG and FG, respectively. The pH plays a crucial role in the maximum sorption of dyes, and the experimental data were successfully adjusted to pseudo-first-order kinetic and Liu isotherm model.

Cadmium/lead tolerance of six Dianthus species and detoxification mechanism in Dianthus spiculifolius

Toxic heavy metal contaminants seriously affect plant growth and human health. Reducing the accumulation of toxic metals by phytoremediation is an effective way to solve this environmental problem. Dianthus spiculifolius Schur is an ornamental plant with strong cold and drought tolerance. Because of its fast growth, well-developed root system, and large accumulation of biomass, D. spiculifolius has potential applications as a heavy metal hyperaccumulator. Therefore, the aim of this study was evaluate the ability of D. spiculifolius and other Dianthus species to remediate heavy metals, with an ultimate goal to identify available genetic resources for toxic metal removal. The cadmium (Cd) and lead (Pb) tolerance and accumulation of six Dianthus species were analyzed comparatively in physiological and biochemical experiments. Compared with the other Dianthus species, D. spiculifolius showed higher tolerance to, and greater accumulation of, Cd and Pb. Second-generation transcriptome analysis indicated that glutathione transferase activity was increased and the glutathione metabolism pathway was enriched with genes encoding antioxidant enzymes (DsGST, DsGST3, DsGSTU10, DsGGCT2-1, and DsIDH-2) that were up-regulated under Cd/Pb treatment by RT-qPCR in D. spiculifolius. When expressed in yeast, DsGST, DsGST3, DsGSTU10 and DsIDH-2 enhanced Cd or Pb tolerance. These results indicate that D. spiculifolius has potential applications as a new ornamental hyperaccumulator plant, and that antioxidant enzymes might be involved in regulating Cd/Pb accumulation and detoxification. The findings of this study reveal some novel genetic resources that can be used to breed new plant varieties that tolerate and accumulate heavy metals.

Functionalized magnetic nanostructured composites and hybrids for photocatalytic elimination of pharmaceuticals and personal care products

Due to rapid urbanization and globalization, an enormous use of pharmaceuticals and personal care products (PPCPs) has resulted their excessive release in water bodies leading to several environmental issues. This release into the environment takes place via household sewage, hospital effluents, manufacturing units and landfill sites etc. The pharmaceuticals and personal care products (PPCPs) are recently listed as emerging contaminants having many adverse effects towards aquatic life, human beings, and the whole ecosystem. The alarming threats of PPCPs demand efficient methods to cope up their hazardous impacts. The conventional wastewater remediations are not specifically designed for the removal of PPCPs and hence, they require advanced technologies and materials for their elimination to ensure water safety. Among various methods employed so far, photocatalysis is considered to be one of the most cost effective and eco-friendly method but it requires a suitable candidate as a photocatalyst. Thanks to the magnetic nanocomposites which have improved the limitations (poor stability, agglomeration, and difficult separation, etc.) of classically used nanomaterials. Magnetic nanocomposites contain at least one component having magnetic properties making their separation easy from the aqueous media after the photodegradation phenomenon. These can be further functionalized with other materials to obtain maximum advantage as photocatalyst. Few examples of such functionalized nanocomposites are inorganic material based magnetic nanocomposites, carbon based magnetic nanocomposites, biomaterial based magnetic nanocomposites, metal-organic framework based magnetic nanocomposites and polymer based magnetic nanocomposites etc. This review covers the global environmental issue of water pollution especially with respect to the PPCPs, their occurrence in aqueous environment and toxic effects on living beings. A comprehensive discussion of the recently reported functionalized magnetic nanocomposites for the photocatalytic removal of PPCPs from water is the main aim of this review. The synthetic/morphological approaches of various functionalized magnetic composites and their mechanism of action are also elaborated. The possible research challenges in the field of magnetic nanocomposites and future research directions are discussed to apply magnetic nanocomposites for wastewater treatment in near future.

Modified Beaded Materials from Recycled Wastes of Bagasse and Bagasse Fly Ash with Iron(III) Oxide-Hydroxide and Zinc Oxide for the Removal of Reactive Blue 4 Dye in Aqueous Solution

Dye contamination in wastewater affects the photosynthesis of aquatic plants and algae by blocking the sunlight, and it induces toxicity to aquatic organisms, which might result in human health effects. Thus, the treatment of dyes in wastewater is required before discharging into the receiving water for safety purposes. Six dye adsorbent materials bagasse beads (BB), bagasse fly ash beads (BFB), bagasse beads with mixed iron(III) oxide-hydroxide (BBF), bagasse fly ash beads with mixed iron(III) oxide-hydroxide (BFBF), bagasse beads with mixed zinc oxide (BBZ), and bagasse fly ash beads with mixed zinc oxide (BFBZ) were synthesized and investigated using various characterization techniques such as X-ray diffractometry (XRD), field emission scanning electron microscopy with focused ion beam (FESEM-FIB), energy dispersive X-ray spectrometry (EDX), and Fourier transform infrared spectroscopy (FTIR). A series of batch experiments on the effects of dosage (0.5-3 g), contact time (3-18 h), temperature (30-80°C), pH (3-11), and initial concentration (30-90 mg/L) were used to investigate reactive blue 4 (RB4) dye removal efficiencies in aqueous solution, and their adsorption isotherms and kinetics were studied for explaining their adsorption patterns and mechanisms. All dye adsorbent materials demonstrated semicrystalline structures, and their surface morphologies had a spherical shape with coarse surfaces. Five main elements of oxygen, carbon, calcium, chlorine, and sodium and six main functional groups of alcohol and carboxylic acid (O-H), carbon dioxide (O=C=O), aromatic groups (C=O and N=O), alkene (C-H), and sodium alginate (C-O-C) were detected in all dye adsorbent materials. For batch tests, they could remove RB4 dye by more than 90%, and BFBF exhibited the highest RB4 dye removal efficiency at 99.36%. Freundlich and pseudo-second-order kinetic models well explained their adsorption patterns and mechanisms, in which BFBF demonstrated a higher maximum adsorption capacity (q _m) of 10.277 mg/g than that of other dye adsorbent materials. Therefore, all dye adsorbent materials offer good potential for further industrial applications.

Composite of methyl polysiloxane and avocado biochar as adsorbent for removal of ciprofloxacin from waters

Two carbon composite materials were prepared by mixing avocado biochar and methyl polysiloxane (MK). Firstly, MK was dissolved in ethanol, and then the biochar was added at different times. In sample 1 (R1), the time of adding biochar was immediately after dissolving MK in ethanol, and in sample 2 (R₂), after 48 h of MK dissolved in ethanol. The samples were characterized by nitrogen adsorption/desorption measurements obtaining specific surface areas (S_BET) of 115 m2 g^-1 (R₁) and 580 m2 g^-1 (R₂). The adsorbents were further characterized using scanning electron microscopy, FTIR and Raman spectroscopy, adsorption of vapors of n-heptane and water, thermal analysis, Bohem titration, pHpzc, and C H N elemental analysis. R₁ and R₂ adsorbents were employed as adsorbents to remove the antibiotic ciprofloxacin from the waters. The t_1/2 and t_0.95 based on the interpolation of Avrami fractional-order were 20.52 and 246.4 min (R₁) and 14.00 and 157.6 min (R₂), respectively. Maximum adsorption capacities (Q_max) based on the Liu isotherm were 10.77 (R₁) and 63.80 mg g^-1 (R₂) for ciprofloxacin. The thermodynamic studies showed a spontaneous and exothermic process for both samples, and the value of ΔH° is compatible with physical adsorption.

Adsorption of p-benzoquinone at low concentrations from aqueous media using biosolid-based activated carbon

The toxic oxidation intermediate p-benzoquinone exists in aqueous environments at dilute concentrations above the fish-toxicity limit of 0.045 mg/L, affecting aquatic life. The reduction of this compound to the concentrations required to achieve safe discharge limits is challenging. In this study, the adsorptive removal of p-benzoquinone by a biosolid-based activated carbon (SBAC) was systematically investigated in batch experiments. The adsorption rate was rapid, and the bulk of p-benzoquinone adsorption occurred within 30 min. The maximum adsorption capacity of SBAC was estimated at 19.6 mg/g using the Langmuir isotherm model. Its adsorptivity was independent of temperature from 6 to 40 °C. The presence of 6 g/L of chloride and 500 mg/L of sulphate did not affect the removal of 1 mg/L p-benzoquinone, whereas 15 mg/L of humic acid media slightly decreased the p-benzoquinone removal from 87.0% to 83.2%. Diffusion, hydrophilic, and electrostatic interactions (i.e., dipole-dipole) govern the adsorption of p-benzoquinone and are influenced by the SBAC surface chemistry. Biosolid-based activated carbon can lower the residual p-benzoquinone to below the fish-toxicity limit of 0.045 mg/L within 1 h of sequential adsorption. Thus, biosolid-based activated carbon can effectively remove p-benzoquinone from aqueous environments; this is a waste-to-resource approach that addresses sustainability (waste disposal) and environmental protection (pollutant removal).

Mangrove forest: An important coastal ecosystem to intercept river microplastics

The research on transportation of river microplastics (MPs) mainly focuses on the estimations of the total contents of river MPs entering the ocean, while the related transportation processes and influence factors were still largely unknown. In our study, the role of mangrove forest, a special tropical ecosystem in the estuary, on the transportations of MPs from rivers to ocean was explored. Except for the ND river with the absence of mangrove forest, the MPs collected from the water sample of the river upstream were much higher than their corresponding downstream (p < 0.05), with the interception rate of riverine MPs by mangrove forests ranging from 12.86% to 56% in dry season and 10.57%-42% in rainy season. The MPs with the characteristics of high density, larger size and regular shape were more easily intercepted. Furthermore, the combined effects of ecological indicators, the properties of mangrove and the hydrodynamic factors jointly determined the interception rates of MPs. This study provides a new perspective and data support for quantifying mangrove forests intercepting MPs in rivers as a factor of MPs retention in global rivers.

Activated Sawdust-Based Adsorbent for the Removal of Basic Blue 3 and Methylene Green from Aqueous Media

Dye pollution is a serious threat to aquatic environment and human health. Although activated carbon is an efficient adsorbent for dye reclamation from effluents, its expressive nature renders its use on large commercial scales. On the other hand, waste biomasses are not effectively used for any beneficial purposes. Sawdust is a waste biomass of wood mills, and due to its small particle sizes, it has the potential to be used as adsorbent. In spite of its uses for cooking purposes, it is sometimes used as adsorbent as such or converted into activated carbon. In raw form, it is not a good adsorbent; however, its adsorption capacity can be increased by applying chemical modifications. In the present study, sawdust of paper mulberry (Broussonetia papyrifera) was used as adsorbent for the removal of basic blue 3 and methylene green from water after chemical modification with NaOH and HCl in 1 : 1. The prepared adsorbent was characterized by SEM and FTIR, whereas the surface area was estimated through an already reported method in literature. Batch experiments were performed to determine the isothermal and kinetic parameters of the selected dyes adsorption on activated sawdust. The effect of adsorbent dosage and temperature on adsorption were also evaluated. The best fit of the kinetic data was achieved with pseudosecond-order model for which $R^2$ values were approximately equal to 1 whereas Langmuir model was most suitable model to explain the isothermal data. The optimum adsorbent dosage was 0.05 g for both of the selected dyes. Different thermodynamic parameters, such as enthalpy ( $∆H=18.5$ and 8.334 kJ/mol respectively for basic blue 3 and methylene green), entropy ( $∆S^{°}=62.41$ and 29.22 kJ/molK respectively for basic blue 3 and methylene green), and Gibbs free energy ( $∆G^{°}=-83.6$ , -410, and -1658 kJ/mol (basic blue)/-65, -519, and -1139 kJ/mol (methylene green), were estimated, and the process was found to be endothermic, spontaneous, and feasible. The increase in $\Delta G^{°}$ with increase in temperature indicates that the adsorption process is favorable at high temperature. The prepared adsorbent could be effectively used in the reclamation of water loaded with other contaminants; however, further experiments are needed to increase the adsorption capacity of the adsorbent.

3-Aminopropyl-triethoxysilane-Functionalized Tannin-Rich Grape Biomass for the Adsorption of Methyl Orange Dye: Synthesis, Characterization, and the Adsorption Mechanism

A biomass amino silica-functionalized material was successfully prepared by a simple sol-gel method. 3-Aminopropyltriethoxysilane (APTES) was added to a tannin-rich grape residue to improve its physicochemical properties and enhance the adsorption performance. The APTES functionalization led to significant changes in the material's characteristics. The functionalized material was efficiently applied in the removal of methyl orange (MO) due to its unique characteristics, such as an abundance of functional groups on its surface. The adsorption process suggests that the electrostatic interactions were the main acting mechanism of the MO dye removal, although other interactions can also take place. The functionalized biomass achieved a very high MO dye maximum adsorption capacity (Q _max) of 361.8 mg g^-1. The temperature positively affected the MO removal, and the thermodynamic studies indicated that the adsorption of MO onto APTES-functionalized biomass was spontaneous and endothermic, and enthalpy is driven in the physisorption mode. The regeneration performance revealed that the APTES-functionalized biomass material could be easily recycled and reused by maintaining very good performance even after five cycles. The adsorbent material was also employed to treat two simulated dye house effluents, which showed 48% removal. At last, the APTES biomass-based material may find significant applications as a multifunctional adsorbent and can be used further to separate pollutants from wastewater.

Sustainable microalgal biomass valorization to bioenergy: Key challenges and future perspectives

The global trend is shifting toward circular economy systems. It is a sustainable environmental approach that sustains economic growth from the use of resources while minimizing environmental impacts. The multiple industrial use of microalgal biomass has received great attention due to its high content of essential nutrients and elements. Nevertheless, low biomass productivity, unbalanced carbon to nitrogen (C/N) ratio, resistant cellular constituents, and the high cost of microalgal harvesting represent the major obstacles for valorization of algal biomass. In recent years, microalgae biomass has been a candidate as a potential feedstock for different bioenergy generation processes with simultaneous treating wastewater and CO₂ capture. An overview of the appealing features and needed advancements is urgently essential for microalgae-derived bioenergy generation. The present review provides a timely outlook and evaluation of biomethane production from microalgal biomass and related challenges. Moreover, the biogas recovery potential from microalgal biomass through different pretreatments and synergistic anaerobic co-digestion (AcoD) with other biowastes are evaluated. In addition, the removal of micropollutants and heavy metals by microalgal cells via adsorption and bioaccumulation in their biomass is discussed. Herein, a comprehensive review is presented about a successive high-throughput for anaerobic digestion (AD) of the microalgal biomass in order to achieve for sustainable energy source. Lastly, the valorization of the digestate from AD of microalgae for agricultural reuse is highlighted.

Salt Removal by Chemically Modified Graphene in Capacitive Deionization (CDI)

Obtaining clean water from salt water by capacitive deionization (CDI) with chemically modified graphene (rGO) was explored in this study. Strong acid (HNO3:H2SO4 = 2:1) was employed to modify rGO to enhance its hydrophilicity and electrochemical properties. Characteristics of rGO with/without acid modification were analyzed by XRD, SEM, FTIR, contact angle, BET, and cyclic voltammetry (CV). Contributions of sulfonic acid groups, hydroxyl groups, and NO2 stretching after acid modification resulted in better wettability and higher specific capacitance of rGO. The contact angle for rGO dropped from 84.9° to 35.1° (am-rGO), indicating improved hydrophilicity of rGO with acid modification. The specific capacitance of am-rGO can reach 150.2 F/g at the scan rate of 1 mV/s. The average NaCl electrosorption capacity of the CDI process with am-rGO was 0.63 mg NaCl/g electrode (10.86 μmol NaCl/g electrode), which indicated rGO with acid modification can enhance the electrosorption capacity by 3.9 times. This study demonstrated that chemical modification can significantly improve the hydrophilicity, electrochemical properties, and electrosorption performance of rGO, which has potential for applications to other carbon-based materials for CDI systems to improve salt removal efficiency.

Heavy metals in leathers, artificial leathers, and textiles in the context of quality and safety of use

The article presents research findings on the content of arsenic, cadmium, chromium, copper, lead, and zinc in extracts from leathers, artificial leathers intended for footwear components, and textiles. After extracting the metals using an artificial acidic sweat solution, their contents were quantitatively determined by atomic absorption spectrometry. In the cotton textiles, the metal contents were in accordance with the OEKO-TEX limits, while regarding the artificial leathers, only the acrylic knit fur had a too high chromium content (1.1 mg/kg) as compared with the requirements of the STANDARD 100 by OEKO-TEX for products intended for children (< 1.0 mg/kg). The chromium content in lining and upper leather (> 228.0 mg/kg) exceeds the limits for children’s products (< 2.0 mg/kg), but also the less restrictive ones for other products (< 200.0 mg/kg). Regarding the other metals, the leathers met the OEKO-TEX requirements. Approved materials may have elevated heavy metal contents, as demonstrated for chromium. The presence of heavy metals in too large amounts in products is a serious problem due to their allergenic and toxic effect. Therefore, action should be taken aimed at more effective detection and elimination of such products from markets and at reducing the use of chemicals containing harmful metals in manufacturing processes.

Green remediation potential of immobilized oxidoreductases to treat halo-organic pollutants persist in wastewater and soil matrices - A way forward

The alarming presence of hazardous halo-organic pollutants in wastewater and soils generated by industrial growth, pharmaceutical and agricultural activities is a major environmental concern that has drawn the attention of scientists. Unfortunately, the application of conventional technologies within hazardous materials remediation processes has radically failed due to their high cost and ineffectiveness. Consequently, the design of innovative and sustainable techniques to remove halo-organic contaminants from wastewater and soils is crucial. Altogether, these aspects have led to the search for safe and efficient alternatives for the treatment of contaminated matrices. In fact, over the last decades, the efficacy of immobilized oxidoreductases has been explored to achieve the removal of halo-organic pollutants from diverse tainted media. Several reports have indicated that these enzymatic constructs possess unique properties, such as high removal rates, improved stability, and excellent reusability, making them promising candidates for green remediation processes. Hence, in this current review, we present an insight of green remediation approaches based on the use of immobilized constructs of phenoloxidases (e.g., laccase and tyrosinase) and peroxidases (e.g., horseradish peroxidase, chloroperoxidase, and manganese peroxidase) for sustainable decontamination of wastewater and soil matrices from halo-organic pollutants, including 2,4-dichlorophenol, 4-chlorophenol, diclofenac, 2-chlorophenol, 2,4,6-trichlorophenol, among others.

Sex differences in the effects of whole-life, low-dose cadmium exposure on postweaning high-fat diet-induced cardiac pathogeneses

We previously showed the development of cardiac remodeling (hypertrophy or fibrosis) in mice with either post-weaning high-fat diet (HFD, 60% kcal fat) feeding or exposure to chronic low-dose cadmium. Here, we determined whether whole-life exposure to environmentally relevant, low-dose cadmium affects the susceptibility of offspring to post-weaning HFD-induced cardiac pathologies and function. Besides, we also determined whether these effects are sex-dependent. Male and female mice were exposed to cadmium-containing (0, 0.5, or 5 parts per million [ppm]) drinking water before breeding; the pregnant mice and dams with offspring continually drank the same cadmium-containing water. After weaning, the offspring were continued on the same regime as their parents and fed either a HFD or normal fat diet for 24 weeks. Cardiac function was examined with echocardiography. Cardiac tissues were used for the histopathological and biochemical (gene and protein expression by real-time PCR and Western blotting) assays. Results showed a dose-dependent cadmium accumulation in the hearts of male and female mice along with decreased cardiac zinc and copper levels only in female offspring. Exposure to 5 ppm, but not 0.5 ppm, cadmium significantly enhanced HFD cardiac effects only in female mice, shown by worsened cardiac systolic and diastolic dysfunction (ejection fraction, mitral E-to-annular e' ratio), increased fibrosis (collagen, fibronectin, collagen1A1), hypertrophy (cardiomyocyte size, atrial natriuretic peptide, β-myosin heavy chain), and inflammation (intercellular adhesion molecule-1, tumor necrosis factor-α, plasminogen activator inhibitor type 1), compared to the HFD group. These synergistic effects were associated with activation of the p38 mitogen-activated protein kinases (MAPK) signaling pathway and increased oxidative stress, shown by 3-nitrotyrosine and malondialdehyde, along with decreased metallothionein expression. These results suggest that whole-life 5 ppm cadmium exposure significantly increases the susceptibility of female offspring to HFD-induced cardiac remodeling and dysfunction. The underlying mechanism and potential intervention will be further explored in the future.

Process Parameters Optimization, Characterization, and Application of KOH-Activated Norway Spruce Bark Graphitic Biochars for Efficient Azo Dye Adsorption

In this work, Norway spruce bark was used as a precursor to prepare activated biochars (BCs) via chemical activation with potassium hydroxide (KOH) as a chemical activator. A Box–Behnken design (BBD) was conducted to evaluate and identify the optimal conditions to reach high specific surface area and high mass yield of BC samples. The studied BC preparation parameters and their levels were as follows: pyrolysis temperature (700, 800, and 900 °C), holding time (1, 2, and 3 h), and ratio of the biomass: chemical activator of 1: 1, 1.5, and 2. The planned BBD yielded BC with extremely high SSA values, up to 2209 m²·g⁻¹. In addition, the BCs were physiochemically characterized, and the results indicated that the BCs exhibited disordered carbon structures and presented a high quantity of O-bearing functional groups on their surfaces, which might improve their adsorption performance towards organic pollutant removal. The BC with the highest SSA value was then employed as an adsorbent to remove Evans blue dye (EB) and colorful effluents. The kinetic study followed a general-order (GO) model, as the most suitable model to describe the experimental data, while the Redlich–Peterson model fitted the equilibrium data better. The EB adsorption capacity was 396.1 mg·g⁻¹. The employment of the BC in the treatment of synthetic effluents, with several dyes and other organic and inorganic compounds, returned a high percentage of removal degree up to 87.7%. Desorption and cyclability tests showed that the biochar can be efficiently regenerated, maintaining an adsorption capacity of 75% after 4 adsorption–desorption cycles. The results of this work pointed out that Norway spruce bark indeed is a promising precursor for producing biochars with very promising properties.

Preparation and Application of Efficient Biobased Carbon Adsorbents Prepared from Spruce Bark Residues for Efficient Removal of Reactive Dyes and Colors from Synthetic Effluents

Biobased carbon materials (BBC) obtained from Norway spruce (Picea abies Karst.) bark was produced by single-step chemical activation with ZnCl2 or KOH, and pyrolysis at 800 °C for one hour. The chemical activation reagent had a significant impact on the properties of the BBCs. KOH-biobased carbon material (KOH-BBC) had a higher specific surface area (SBET), equal to 1067 m2 g−1, larger pore volume (0.558 cm3 g−1), more mesopores, and a more hydrophilic surface than ZnCl2-BBC. However, the carbon yield for KOH-BBC was 63% lower than for ZnCl2-BBC. Batch adsorption experiments were performed to evaluate the ability of the two BBCs to remove two dyes, reactive orange 16 (RO-16) and reactive blue 4 (RB-4), and treat synthetic effluents. The general order model was most suitable for modeling the adsorption kinetics of both dyes and BBCs. The equilibrium parameters at 22 °C were calculated using the Liu model. Upon adsorption of RO-16, Qmax was 90.1 mg g−1 for ZnCl2-BBC and 354.8 mg g−1 for KOH-BBC. With RB-4, Qmax was 332.9 mg g−1 for ZnCl2-BBC and 582.5 mg g−1 for KOH-BBC. Based on characterization and experimental data, it was suggested that electrostatic interactions and hydrogen bonds between BBCs and RO-16 and RB-4 dyes played the most crucial role in the adsorption process. The biobased carbon materials showed high efficiency for removing RO-16 and RB-4, comparable to the best examples from the literature. Additionally, both the KOH- and ZnCl2-BBC showed a high ability to purify two synthetic effluents, but the KOH-BBC was superior.