Biofouling control based on bacterial quorum quenching with a new application: Rotary microbial carrier frame

Quorum Quenching Approaches against Bacterial-Biofilm-Induced Antibiotic Resistance

With the widespread phenomenon of antibiotic resistance and the diffusion of multiple drug-resistant bacterial strains, enormous efforts are being conducted to identify suitable alternative agents against pathogenic microorganisms. Since an association between biofilm formation and antibiotic resistance phenotype has been observed, a promising strategy pursued in recent years focuses on controlling and preventing this formation by targeting and inhibiting the Quorum Sensing (QS) system, whose central role in biofilm has been extensively demonstrated. Therefore, the research and development of Quorum Quenching (QQ) compounds, which inhibit QS, has gradually attracted the attention of researchers and has become a new strategy for controlling harmful microorganisms. Among these, a number of both natural and synthetic compounds have been progressively identified as able to interrupt the intercellular communication within a microbial community and the adhesion to a surface, thus disintegrating mature/preformed biofilms. This review describes the role played by QS in the formation of bacterial biofilms and then focuses on the mechanisms of different natural and synthetic QS inhibitors (QSIs) exhibiting promising antibiofilm ability against Gram-positive and Gram-negative bacterial pathogens and on their applications as biocontrol strategies in various fields.

Non-destructive monitoring and prediction of fouling by organic matters and residual anionic coagulant during membrane process

Physical fouling characteristics on silicon carbide (SiC) membranes induced by various organic matter compounds vary depending on the presence of calcium ions (Ca2+). Both destructive techniques (morphological surface analysis) and non-destructive techniques (fouling properties monitoring) were used to determine the fouling mechanisms and behavior during the membrane filtration systems. Destructive analysis and a modified Hermia model were employed to assess the fouling mechanisms. Fouling behavior was also analyzed through non-destructive monitoring techniques including optical coherence tomography (OCT) and three-dimensional laser scanning confocal microscopy (3D-LSM). At concentrations of 10, 30, and 100 mg/L without Ca2+, the flux decreased by 57-95% for humic acid (HA) and anionic polyacrylamide (APAM). APAM exhibited a notable removal rate of up to 56% without Ca2+. At concentration of 10, 30, and 100 mg/L in the absence of Ca2+, the flux decreased by 6-8% for sodium alginate (SA). However, the addition of Ca2+ led to a reduction in the flux for SA by up to 91% and resulted in a removal rate of 40%. Furthermore, addition of Ca2+ led to an alteration of the fouling characteristics of HA and SA. In the case of HA, higher concentrations resulted in elevated thickness and roughness with correlation coefficients of 0.991 and 0.992, respectively. For SA, increased SA concentration led to a thicker (correlation coefficient of 0.999) but smoother surfaces (correlation coefficients of 0.502). Monitoring of these physical characteristics of the fouling layer through non-destructive analysis is crucial for effective fouling management, optimization of the system performance and extending the lifespan of the membrane. By continuously assessing the fouling layer thickness and surface roughness, we expect to be able to provide insights on the fouling behavior, identify trends, that can help scientists and engineers to make informed decisions regarding fouling control strategies in future.

Optimum quorum quenching bacteria concentration in the better-quality cell entrapping beads to control biofouling in membrane bioreactor

Quorum quenching (QQ) by cell entrapping beads (CEBs) is known to inhibit biofouling by its biological and physical cleaning effect. Although there are better QQ media reported, due to the ease of fabrication of QQ-CEBs, this study focused on improving the quality of CEBs by comparing two distinct bead-making methods - polyvinyl alcohol-alginate (PVA-alginate) and phase inversion - and on finding the optimum concentration of QQ bacteria in the CEBs. The evaluation of PVA-alginate bead showed better uniformity, and higher mechanical and chemical strength in comparison with the phase inversion bead. Through the operations of two control membrane bioreactors (MBRs) (no bead, vacant bead) and four QQ-MBRs with different Rhodococcus sp. BH4 concentrations (2.5-15 mg cell ml-1) in PVA-alginate CEBs, the maximum QQ effect was observed by 5 mg ml-1 BH4 concentration beads. This implies that an optimum cell concentration of QQ-CEBs is crucial to economically improve MBR performance using QQ.

d-tyrosine enhances disoctyl dimethyl ammonium chloride on alleviating SRB corrosion

Microbiologically influenced corrosion (MIC) caused by sulfate reducing bacteria (SRB) is a serious challenge in many industries, but biofilm greatly decreases the toxicity of bactericides to cell inside. d-amino acids are potential enhancers for bactericides due to their excellent performance on biofilm inhibition. However, the mechanism of d-amino acid cooperating with bactericides for MIC inhibition is still unknown. In this study, d-tyrosine（D-Tyr）and disoctyl dimethyl ammonium chloride (DDAC) were selected as the typical d-amino acid and bactericide, respectively, to evaluate their synergetic inhibition on the corrosion caused by Desulfovibrio vulgaris. D-Tyr obviously enhanced the role of DDAC in inhibiting corrosion with high corrosion inhibition efficiency at 77.23 %. The attachment of EPS and live cells on the coupon surface decreased in the presence of D-Try, leading to more cells directly exposed to DDAC. Besides, D-Try decreased the amount of live cells on the surface and thus reduced the utilization of Fe by SRB and corrosion current. Moreover, dead cells settling to the coupon surface may form a protective lay to retard the contact between live SRB and Fe, leading to slow cathode reaction and less corrosion. Therefore, D-Tyr can reduce the coverage of biofilm, thereby reducing its protective effect on SRB and achieving better corrosion inhibition effect. This work provides a new strategy for improving bactericides and inhibiting MIC.

Biofilm-developed biomass residues as novel bulking agents and microbial carriers for synergistically enhanced bioevaporation: Degradation potential and contribution to metabolic heat

Economical and easily prepared bulking agents and microbial carriers are essential in the practical application of bioevaporation process. Biofilm-developed biomass residues not only provide structural support and microbial sources but also may contribute metabolic heat to the bioevaporation process, achieving the enhanced water evaporation and synergistic treatment of biomass residues. In this study, biofilm was cultivated on the rice straw, wheat straw, sawdust, corncob, luffa cylindrica and palm first, then those biofilm-developed biomass residues were successfully used as the bulking agents and microbial carriers in food waste bioevaporation. The degradation potential (volatile solid degradation ratio) of those biomass residues was in the order of corncob (23.96%), wheat straw (21.12%), rice straw (14.57%), luffa cylindrica (11.02%), sawdust (-2.87%) and palm (-9.24%). It's primarily the degradation of the major components, cellulose and hemicellulose, in corncob and wheat straw governed the metabolic heat contribution (91.73 and 79.61%) to the bioevaporation process. While the high lignin content in sawdust (14.57%) and palm (28.62%) caused negligible degradation of cellulose and hemicellulose, hence made them only function as structural supporter and did not contribute any metabolic heat. Moreover, though the metabolic heat contribution of rice straw and luffa cylindrica reached 58.19 and 37.84%, their lowest lignocellulose content (62.99 and 65.95%) and their lower density, as well as the dominated Xanthomonas (bacteria) and Mycothermus (fungi) led to their rapid collapse during the repeated cycles of bioevaporation. The greatest abundance of thermophilic bacteria (22.3-88.0%) and thermophilic fungi (82.0-99.3%) was observed in the corncob pile. Furthermore, considering the Staphylococcus (pathogenic bacteria) and Candida (animal pathogen) was effectively inhibited, the biofilm-developed corncob was the most favorable bulking agents and microbial carrier for the synergistic bioevaporation of highly concentrated organic wastewater and biomass residues.

Biofouling in Membrane Bioreactors-Mitigation and Current Status: a Review

Biological fouling as termed biofouling is caused by varied living organisms and is difficult to eliminate from the environment thus becoming a major issue during membrane bioreactors. Biofouling in membrane bioreactors (MBRs) is a crucial problem in increasing liquid pressure due to reduced pore diameter, clogging of the membrane pores, and alteration of the chemical composition of the water which greatly limits the growth of MBRs. Thus, membrane biofouling and/or microbial biofilms is a hot research topic to improve the market competitiveness of the MBR technology. Though several antibiofouling strategies (addition of bioflocculant or sponge into MBRs) came to light, biological approaches are sustainable and more practicable. Among the biological approaches, quorum sensing-based biofouling control (so-called quorum quenching) is an interesting and promising tool in combating biofouling issues in the MBRs. Several review articles have been published in the area of membrane biofouling and mitigation approaches. However, there is no single source of information about biofouling and/or biofilm formation in different environmental settings and respective problems, antibiofilm strategies and current status, quorum quenching, and its futurity. Thus, the objectives of the present review were to provide latest insights on mechanism of membrane biofouling, quorum sensing molecules, biofilm-associated problems in different environmental setting and antibiofilm strategies, special emphasis on quorum quenching, and its futurity in the biofilm/biofouling control. We believe that these insights greatly help in the better understanding of biofouling and aid in the development of sustainable antibiofouling strategies.

Effect of quorum quenching on biofouling control and microbial community in membrane bioreactors by Brucella sp. ZJ1

Quorum quenching (QQ) has been demonstrated to be a novel technique for controlling biofouling in membrane bioreactors (MBRs), as it can significantly inhibit biofilm formation by disrupting quorum sensing (QS). The exploration of new QQ bacterial strains and the evaluation of their performance in mitigating membrane fouling in MBR systems is significant. In this study, an efficient QQ strain, Brucella sp. ZJ1 was encapsulated in alginate beads and evaluated for its ability to mitigate biofouling. The findings revealed that MBR with QQ beads extended the operation time by 2-3 times without affecting pollutant degradation. QQ beads maintained approximately 50% QQ activity after more than 50 days operation, indicating a long-lasting and endurable QQ effect. The QQ effect reduced extracellular polymeric substance (EPS) production especially in terms of polysaccharide and protein by more than 40%. QQ beads in the MBR also reduced the cake resistance and the irreversible resistance of membrane biofouling. Metagenomic sequencing suggests that QQ beads suppressed the QS effect and increased the abundance of QQ enzyme genes, ultimately inducing efficient membrane biofouling control.

Enhancing quorum quenching media with 3D robust electrospinning coating: A novel biofouling control strategy for membrane bioreactors

Bacterial quorum quenching (QQ) is an effective strategy for controlling biofouling in membrane bioreactor (MBR) by interfering the releasing and degradation of signal molecules during quorum sensing (QS) process. However, due to the framework feature of QQ media, the maintenance of QQ activity and the restriction of mass transfer threshold, it has been difficult to design a more stable and better performing structure in a long period of time. In this research, electrospun fiber coated hydrogel QQ beads (QQ-ECHB) were fabricated by using electrospun nanofiber coated hydrogel to strengthen layers of QQ carriers for the first time. The robust porous PVDF 3D nanofiber membrane was coated on the surface of millimeter-scale QQ hydrogel beads. Biocompatible hydrogel entrapping quorum quenching bacteria (sp.BH4) was employed as the core of the QQ-ECHB. In MBR with the addition of QQ-ECHB, the time to reach transmembrane pressure (TMP) of 40 kPa was 4 times longer than conventional MBR. The robust coating and porous microstructure of QQ-ECHB contributed to keeping a lasting QQ activity and stable physical washing effect at a very low dosage (10g beads/5L MBR). Physical stability and environmental-tolerance tests also verified that the carrier can maintain the structural strength and keep the core bacteria stable when suffering long-term cyclic compression and great fluctuations in sewage quality.

Identification of quorum sensing-regulated Vibrio fortis as potential pathogenic bacteria for coral bleaching and the effects on the microbial shift

Coastal pollution, global warming, ocean acidification, and other reasons lead to the imbalance of the coral reef ecosystem, resulting in the increasingly serious problem of coral degradation. Coral bleaching is often accompanied by structural abnormalities of coral symbiotic microbiota, among which Vibrio is highly concerned. In this study, Vibrio fortis S10-1 (MCCC 1H00104), isolated from sea cucumber, was used for the bacterial infection on coral Seriatopora guttatus and Pocillopora damicornis. The infection of S10-1 led to coral bleaching and a significant reduction of photosynthetic function in coral holobiont, and the pathogenicity of V. fortis was regulated by quorum sensing. Meanwhile, Vibrio infection also caused a shift of coral symbiotic microbial community, with significantly increased abundant Proteobacteria and Actinobacteria and significantly reduced abundant Firmicutes; on genus level, the abundance of Bacillus decreased significantly and the abundance of Rhodococcus, Ralstonia, and Burkholderia-Caballeronia-Paraburkholderia increased significantly; S10-1 infection also significantly impacted the water quality in the micro-ecosystem. In contrast, S10-1 infection showed less effect on the microbial community of the live stone, which reflected that the microbes in the epiphytic environment of the live stone might have a stronger ability of self-regulation; the algal symbionts mainly consisted of Cladocopium sp. and showed no significant effect by the Vibrio infection. This study verified that V. fortis is the primary pathogenic bacterium causing coral bleaching, revealed changes in the microbial community caused by its infection, provided strong evidence for the "bacterial bleaching" hypothesis, and provided an experimental experience for the exploration of the interaction mechanism among microbial communities, especially coral-associated Vibrio in the coral ecosystem, and potential probiotic strategy or QS regulation on further coral disease control.

Modification of reinforced hollow fiber membranes with WO3 nanosheets for treatment of textile wastewater by membrane bioreactor

In this study, performance of braid reinforced hollow fiber membrane containing polyvinylidene fluoride (PVDF) embedded with tungsten trioxide (WO₃) nanosheets in a membrane bioreactor (MBR) was examined for textile wastewater treatment. The WO₃ nanosheets was synthesized and blended at different concentrations (0.1-0.02 wt%) in casting solutions of the membranes. The WO₃ nanosheets characterized using various tests such as XRD, FTIR, SEM, EDS, dot-mapping, and TEM. Furthermore, the effects of the increased WO₃ nanosheets into the PVDF matrix on the membrane morphology, hydrophilicity, permeability, antifouling, and COD and color removal efficiency was investigated. The addition of 0.1 wt% of the nanosheets reduces the water contact angle from 69.3° to 62.5° while increasing overall porosity from 37.5 to 43.2%. COD and color removal for PVDF/0.10 wt% WO₃ membrane was between 86-89% and 72-76%, respectively. While the TMP of modified WO₃ membranes did not significantly increase due to antimicrobial properties of the WO₃ nanosheets, the TMP of the pure PVDF membrane increase, indicating considerable cake layer fouling. The results of this study showed that modification of PVDF braid reinforced hollow fiber membrane using WO₃ nanosheets is promising membrane for MBR systems.

Photolytic quorum quenching effects on the microbial communities and functional gene expressions in membrane bioreactors

Photolytic quorum quenching by ultraviolet A (UVA) irradiation is an effective strategy for controlling membrane bioreactor (MBR) biofouling; however, its effects on MBR microbial communities and functional genes have not yet been explored. Here, we report on the effects of the UVA irradiation, which mitigates membrane biofouling, on the microbial community structures, alpha and beta diversities, and functional gene expressions in the MBR mixed liquor and biocake (membrane fouling layer) for the first time. The results show that the microbial communities become less diversified when alternating UVA is applied to the MBRs. The changes in the community structure are highly influenced by spatiotemporal factors, such as microbial habitats (mixed liquor and biocake) and reactor operation time, although UVA irradiation also has some impacts on the community. The relative abundance of the Sphingomonadaceae family, which can decompose the furan ring of autoinducer-2 (AI-2) signal molecules, becomes greater with continuous UVA irradiation. Xanthomonadaceae, which produces biofilm-degrading enzymes, is also more abundant with UVA photolysis than without it. Copies of monooxygenase and hydroxylase enzyme-related genes increase in the MBR with longer UVA exposures (i.e., continuous UVA). These enzymes seem to be inducible by UVA, enhancing the AI-2 inactivation. In conclusion, UVA irradiation alters the microbial community and the metabolism in the MBR, contributing to the membrane biofouling mitigation.

Innovative Biofouling Control for Membrane Bioreactors in Cold Regions by Inducing Environmental Adaptation in Quorum-Quenching Bacteria

Bacterial quorum quenching (QQ), whose mechanism involves the degradation of quorum-sensing signal molecules, is an effective strategy for controlling biofouling in membrane bioreactors (MBRs). However, MBRs operated at low temperatures, either due to cold climates or seasonal variations, exhibit severe deterioration in QQ efficiency. In this study, a modified culture method for Rhodococcus sp. BH4, a QQ bacterium, was developed to induce environmental adaptation in cold regions. BH4-L, which was prepared by the modified culture method, showed enhancement in QQ efficiency at low temperatures. The higher QQ efficiency obtained by employing BH4-L at 10 °C (compared with that obtained by employing BH4 at 10 °C) was attributed to the higher live/dead cell ratio in the BH4-L-entrapping beads. When BH4-L-entrapping beads were applied to lab-scale MBRs operated at low temperatures, membrane biofouling in MBRs at low temperatures was successfully mitigated because BH4-L could substantially reduce the concentration of signal molecules (N-acyl homoserine lactones) in the biocake. Employing BH4-L in QQ-MBRs could offer a novel solution to the problem of severe membrane biofouling in MBRs in cold regions.

Effect of Aeration Intensity on Performance of Lab-Scale Quorum-Quenching Membrane Bioreactor

Biofouling is one of the main drawbacks of membrane bioreactors (MBRs). Among the different methods, the quorum-quenching (QQ) technique is a novel method as it delays biofilm formation on the membrane surface through disruption of bacterial cell-to-cell communication and thus effectively mitigates membrane biofouling. QQ bacteria require a certain concentration of dissolved oxygen to show their best activities. Despite the importance of the amount of aeration, there have not been enough studies on aeration condition utilizing the separate determination of pure QQ effect and physical cleaning effect. This research aimed to find the optimum aeration intensity by separation of the two effects from QQ and physical cleaning. Three bead type conditions (no bead, vacant bead, and QQ beads) at three aeration intensities (1.5, 2.5, and 3.5 L/min representing low, medium, and high aeration intensity) were applied. From the results, no QQ effect and small QQ effect were observed at low and high aeration, while the greatest QQ effect (48.2% of 737 h improvement) was observed at medium aeration. The best performance was observed at high aeration with QQ beads having a 1536 h operational duration (303% improvement compared to the no bead condition); however, this excellent performance was attributed more to the physical cleaning effect than to the QQ effect.

Quorum quenching strategy for biofouling control in membrane photobioreactor

This study aims to reduce membrane fouling in membrane photobioreactor (MPBR) through the quorum quenching (QQ) strategy. For this purpose, the QQ beads (immobilized Rhodococcus sp. BH4) were added to the MPBR, and antifouling ability was evaluated in consideration of the changes in transmembrane pressure (TMP), extracellular polymeric substance (EPS), microbial community, and cake layer morphology on the membrane surface. The results showed that the TMP of control MPBR (MPBR-C) reached 818 mbar and 912 mbar on the operation hours of 35 and 170, while the TMP of experimental MPBR (MPBR-QQ) was only 448 mbar and 676 mbar, respectively. The QQ strategy effectively reduced the EPS content in MPBR. The microscopic observations indicated that the QQ diminished the cake layer formation and pore-blocking on the membrane surface. Comparisons of 16S and 18S gene communities revealed minor differences between bacterial and eukaryotic species in MPBRs at phylum and class levels.

Efficient biostimulants for bacterial quorum quenching to control fouling in MBR

Quorum quenching (QQ), which disrupts bacterial communication and biofilm formation, could alleviate biofouling in MBR. QQ bio-stimulus possessing similar conserved moiety as the signal molecule could promote indigenous QQ bacteria, and thus successfully alleviate biofouling in MBR. However, efficient biostimulant has been barely explored for QQ enhancement in activated sludge system. This study extensively enumerated the potential QQ bio-stimuli, and examined their efficacy on QQ promotion for activated sludge. Moreover, the effect of the QQ consortia on fouling mitigation was also investigated. The results indicated that gamma-caprolactone (GCL), d-xylonic acid-1,4-lactone (XAL), gamma-heptalactone (GHL), urea, and acetamide proved effective in promoting AHLs inactivating activity of activated sludge. GCL, XAL, and GHL intensified the lactonase activity, while urea and acetamide augmented acylase activity. While coupled with beads entrapment, GCL consortia beads, XAL consortia beads, and urea consortia beads effectively disrupted quorum sensing (QS) and controlled membrane fouling in MBR. This work found out several optional bio-stimuli valid for tuning QQ in activated sludge system, and provided easily available and economical alternatives for QQ biostimulation, meanwhile the proposed QQ-MBR approach through QQ biostimulation and consortia entrapment also proved effective and practical.

Biological mechanism of alleviating membrane biofouling by porous spherical carriers in a submerged membrane bioreactor

In this study, porous spherical carriers were fixed around the hollow fiber membrane module to mitigate membrane biofouling. Two MBRs (R1 without carriers, R2 with carriers) were operated for 31 days under identical operating conditions to investigate the effects of the carriers on the reactor performances, the production of extracellular polymeric substances (EPS), the level of N-acyl-homoserine lactones (AHLs), and the microbial communities. The results showed that the presence of carriers in MBR was conducive to nitrogen removal and decreased the total membrane filtration resistance by about 1.7 times. Slower transmembrane pressure (TMP) rise-up, thinner bio-cakes, lower EPS production, and fewer tryptophan and aromatic proteins substances on the membrane surface were observed in R2. The polysaccharides secretion of EPS in bio-cakes was mainly regulated by C4-HSL and 3OC6-HSL in the presence of carriers. The microbial community analysis revealed that carriers addition reduced the relative abundance of EPS and AHL producing bacteria in the membrane bio-cakes and enriched the accumulation of functional bacteria conducive to nutrient removal in the mixed liquor. This study provided an in-depth understanding for the application of porous spherical carriers to alleviate membrane biofouling.

Membrane-Based Harvesting Processes for Microalgae and Their Valuable-Related Molecules: A Review

The interest in microalgae production deals with its role as the third generation of feedstock to recover renewable energy. Today, there is a need to analyze the ultimate research and advances in recovering the microalgae biomass from the culture medium. Therefore, this review brings the current research developments (over the last three years) in the field of harvesting microalgae using membrane-based technologies (including microfiltration, ultrafiltration and forward osmosis). Initially, the principles of membrane technologies are given to outline the main parameters influencing their operation. The main strategies adopted by the research community for the harvesting of microalgae using membranes are subsequently addressed, paying particular attention to the novel achievements made for improving filtration performance and alleviating fouling. Moreover, this contribution also gives an overview of the advantages of applying membrane technologies for the efficient extraction of the high added-value compounds in microalgae cells, such as lipids, proteins and carbohydrates, which together with the production of renewable biofuels could boost the development of more sustainable and cost-effective microalgae biorefineries.

Effect of quorum quenching on EPS and size-fractioned particles and organics in anaerobic membrane bioreactor for domestic wastewater treatment

Quorum quenching (QQ) has been applied as a promising membrane fouling control strategy for anaerobic membrane bioreactors (AnMBRs). Nevertheless, long-term operation of AnMBRs for real domestic wastewater (DWW) treatment needs to be systematically studied to evaluate comprehensive membrane fouling mechanisms and bioprocess performance. In this study, the impact of QQ on membrane fouling was investigated using a quorum quenching AnMBR (QQAnMBR) deploying a bead-entrapped facultative quorum quenching consortium (FQQ) to treat DWW. FQQ was shown to prolong membrane filtration operation by an average of 75%. Reduced proteins (p < 0.005) and carbohydrates (p < 0.005) in the extracellular polymeric substances (EPS) of mixed liquor (ML) were key differentiators that led to lower cake layer (CL) formation. Additionally, reduced biopolymers production (p < 0.05) in EPS improved sludge dewaterability. The findings suggested that QQ could alter fluorescent microbial metabolites of both EPS and CL as unveiled by excitation-emission matrix spectra pattern. Furthermore, colloidal particles (i.e., particles with size larger than 0.45 μm in ML supernatants) production was retarded by QQ, thereafter, also contributed to the reduced CL formation. Pore blockage was slightly increased by QQ, which might be attributed to pore blockage by large (∼230 nm) and small organic compounds (∼51 nm) in soluble microbial products (SMP). However, QQ had no significant impact on organic concentration of SMP, and QQ was not associated with particle size distribution of biomass. QQ performance was further affirmed through suppressed production of C4-HSL, 3-OXO-C6-HSL, and C6-HSL. The overall AHLs degradability of FQQ was well-maintained even after five membrane service cycles (total operation of 70 d). Moreover, QQ had no compromised impact on treatment performance (i.e., chemical oxygen demand (COD) removal and methane yield). Collectively, this study bridged the knowledge gap to bring forward QQ technology in AnMBR for widespread domestic wastewater treatment application.

Current Advances in Biofouling Mitigation in Membranes for Water Treatment: An Overview

Membranes, as the primary tool in membrane separation techniques, tend to suffer external deposition of pollutants and microorganisms depending on the nature of the treating solutions. Such issues are well recognized as biofouling and is identified as the major drawback of pressure-driven membrane processes due to the influence of the separation performance of such membrane-based technologies. Herein, the aim of this review paper is to elucidate and discuss new insights on the ongoing development works at facing the biofouling phenomenon in membranes. This paper also provides an overview of the main strategies proposed by “membranologists” to improve the fouling resistance in membranes. Special attention has been paid to the fundamentals on membrane fouling as well as the relevant results in the framework of mitigating the issue. By analyzing the literature data and state-of-the-art, the concluding remarks and future trends in the field are given as well.

Mitigating biofouling with a vanillin coating on thin film composite reverse osmosis membranes

Several methods, such as pretreatment, membrane surface modification, feed water chlorination, and chemical cleaning, have recently been applied to control biofouling on reverse osmosis (RO) membranes-with limited success. As an alternative, compounds that inhibit bacterial quorum sensing can be used to disrupt formation of bacterial colonies. In this study, anti-biofouling using vanillin, which is a natural substance among quorum sensing inhibitor compounds, was trialed, by modifying RO membrane surfaces with vanillin, at various concentrations. We then reviewed consequential changes to membrane surface characteristics and vanillin anti-biofouling properties. A long-term RO membrane simulator was used to analyze permeability, contact angle was measured for hydrophilicity evaluation, and membrane surface morphology was analyzed, through atomic force microscopy and scanning electron microscopy. A quorum quenching effect was confirmed by utilizing Petrifilm to count bacteria on the surface of a modified membrane. As a result, the permeability of the surface modified membranes was slightly decreased compared to the pristine membrane, but the hydrophilicity was increased, and the number of colonies decreased remarkably, the membrane modified with 0.5 M vanillin outperforming that modified with 0.25 M vanillin.

Quorum quenching in anaerobic membrane bioreactor for fouling control

Quorum quenching (QQ) is an effective method to control membrane biofouling in aerobic membrane bioreactors (AeMBRs). However, it is not clear if QQ is feasible in an anaerobic membrane bioreactor (AnMBR). In this study, Microbacterium. sp that has QQ capability was embedded in alginate beads, known as QQ beads (QQB), and applied in a lab-scale AnMBR to investigate their potential in fouling control. With the addition of QQB, the operating period of AnMBR-QQB reactor was prolonged by about 8-10 times at constant flux operation before reaching the pre-set maximum transmembrane pressure (TMP). The concentration of Acyl-homoserine lactones (AHLs) in the bulk liquid was significantly higher during the 'TMP jump' period compared to QQB and control phases, while AHLs in the membrane foulants were remarkably lower in QQB phase compared to control phase. Furthermore, a much lower level of soluble microbial production (SMP) was observed in QQB phases. Extracellular polymeric substance (EPS), protein in particular, was reduced by 39.73-80.58% in the cake layer of the membrane from QQB phases. Significant changes of organic functional groups were observed in cake layer from QQB membrane as compared with that from control membrane. At the end of operation, bio-polymer (BP), building blocks (BB) and low molecular weight (LMW) organic matters increased in the foulant from control phases but such increase was not observed in QQB phase. After long-term operation, revival of QQB is required due to the declined activity for AHLs degradation.

Roles of quorum sensing in biological wastewater treatment: A critical review

Quorum sensing (QS) and quorum quenching (QQ) are increasingly reported in biological wastewater treatment processes because of their inherent roles in biofilm development, bacterial aggregation, granulation, colonization, and biotransformation of pollutants. As such, the fundamentals and ubiquitous nature of QS bacteria are critical for fully understanding the process of the wastewater treatment system. In this article, the details of QS-based strategies related to community behaviors and phenotypes in wastewater treatment systems were reviewed. The molecular aspects and coexistence of QS and QQ bacteria were also mentioned, which provide evidence that future wastewater treatment will indispensably rely on QS-based strategies. In addition, recent attempts focusing on the use of QQ for biofilm or biofouling control were also summarized. Nevertheless, there are still several challenges and knowledge gaps that warrant future targeted research on the ecological niche, abundance, and community of QS- and QQ-bacteria in environmental settings or engineered systems.

Quorum sensing and quenching in membrane bioreactors: Opportunities and challenges for biofouling control

Membrane biofouling, due to biofilm growth after planktonic bacteria attachment to a membrane, is a major bottleneck limiting the energy-efficient operation and maintenance of membrane bioreactors (MBRs). Microbial communications, known as quorum sensing (QS), are responsible for this biofouling behavior. Novel strategies for stopping this communication, known as quorum quenching (QQ), appear to be successful for biofouling control in MBRs used for wastewater treatment. This review describes recent information regarding the signal molecules and mechanisms responsible for QS behaviors, promising approaches for QQ (enzymatic, bacterial, fungal, photocatalytic, mimicking, and biostimulating methods), and efficient fabrication and use of QQ media for MBR applications. We discuss the opportunities and challenges of QQ techniques for their further improvement and practical use in MBRs.

Evaluation of a novel quorum quenching strain for MBR biofouling mitigation

Membrane biofouling, due to Soluble Microbial Products (SMP) and Extracellular Polymeric Substances (EPS) deposition, results in reduction of the performance of Membrane Bioreactors (MBRs). However, recently, a new method of biofouling control has been developed, utilizing the interference of the bacterial inter- and intra-species' communication. Bacteria use Quorum Sensing (QS) to regulate the production of SMP and EPS. Therefore, disruption of Quorum Sensing (Quorum Quenching: QQ), by enzymes or microorganisms, may be a simple mean to control membrane biofouling. In the present study, a novel QQ-bacterium, namely Lactobacillus sp. SBR04MA, was isolated from municipal wastewater sludge and its ability to mitigate biofouling was evaluated by monitoring the changes in critical flux and transmembrane pressure, along with the production of EPS and SMP, in a lab-scale MBR system treating synthetic wastewater. Lactobacillus sp. SBR04MA showed great potential for biofouling control, which was evidenced by the ∼3-fold increase in critical flux (8.3 → 24.25 L/m²/h), as well as by reduction of the SMP and EPS production, which was lower during the QQ-period when compared against the control period. Furthermore, the addition of the QQ-strain did not affect the COD removal rate. Results suggested that Lactobacillus sp. SBR04MA represents a novel and promising strain for biofouling mitigation and enhancement of MBRs performance.

Preliminary investigation of quorum quenching effects on sludge quantity and quality of activated sludge process

The Quorum Sensing (QS) system has attracted the interest of researchers as a cell-cell communication system. In activated sludge processes, the production of extracellular polymeric substances (EPS), biofilms and floc formation are regulated by the QS system. Hence, disruption of the QS system, called Quorum Quenching (QQ), could have a significant effect on the quality and quantity of excess sludge. In the present research, the quorum quenching bacteria, Rhodococcus sp. BH4 was used as a quorum quencher and was entrapped in an alginate structure (QQ beads). Three separate sequential batch reactors (SBR) were constructed and operated as a control reactor, a Low-QQ reactor (containing 150 QQ beads), and a High-QQ reactor (containing 600 QQ beads). Results indicated that the presence of QQ beads in the aeration reactor leads to a decrease in EPS content and mean floc particle size in the both Low-QQ and High-QQ reactors. The eukaryotic community was changed significantly so that the QS disruption caused an enhancement in microbial predation. The presence of QQ beads also led to a 16 and a 26% decrease in the Y_obs coefficient within the Low-QQ and High-QQ reactors, respectively. Findings of this research revealed a new application of the QQ system in the activated sludge process, but additional studies are needed.

Membrane biofouling behaviors at cold temperatures in pilot-scale hollow fiber membrane bioreactors with quorum quenching

In this study, the seasonality of the biofouling behavior of pilot-scale membrane bioreactors (MBRs) run in parallel with vacant sheets and quorum quenching (QQ) sheets using real municipal wastewater was investigated. QQ media delayed fouling, but low temperatures caused severe biofouling. The greater amount of extracellular polymeric substances (EPSs) produced in cold weather was responsible for the faster biofouling of a membrane, even with QQ media. There were significant negative relationships between EPS levels and water temperature. Cold weather was detrimental to the degradation of quorum sensing signal molecules by QQ sheets, whose activity was restored with a higher dose of QQ bacteria. The QQ bacteria in the sheets experienced a slight loss in activity during the early stage of the field test, but survived in the pilot-scale MBR fed with real wastewater. There were no significant discrepancies in treatment efficiency among conventional, vacant, and QQ MBRs.

Stopping Autoinducer-2 Chatter by Means of an Indigenous Bacterium ( Acinetobacter sp. DKY-1): A New Antibiofouling Strategy in a Membrane Bioreactor for Wastewater Treatment

Bacterial quorum quenching (QQ) by means of degrading signaling molecules has been applied to antibiofouling strategies in a membrane bioreactor (MBR) for wastewater treatment. However, the target signaling molecules have been limited to N-acyl homoserine lactones participating in intraspecies quorum sensing. Here, an approach to disrupting autoinducer-2 (AI-2) signaling molecules participating in interspecies quorum sensing was pursued as a next-generation antibiofouling strategy in an MBR for wastewater treatment. We isolated an indigenous QQ bacterium ( Acinetobacter sp. DKY-1) that can attenuate the expression of the quorum-sensing (QS) response through the inactivation of an autoinducer-2 signaling molecule, 4,5-dihydroxy-2,3-pentanedione (DPD), among four kinds of autoinducer-2 QS bacteria. DKY-1 released AI-2 QQ compounds, which were verified to be hydrophilic with a molecular weight of <400 Da. The addition of DKY-1 entrapping beads into an MBR significantly decreased DPD concentration and remarkably reduced membrane biofouling. This new approach, combining molecular biology with wastewater engineering, could enlarge the range of QQ-MBR for antibiofouling and energy savings in the field of wastewater treatment.

Evaluation of a novel anti-biofouling microorganism (Bacillus sp. T5) for control of membrane biofouling and its effect on bacterial community structure in membrane bioreactors

The effects of a newly isolated quorum quenching (QQ) bacteria (Bacillus sp. T5) on the microbial community has been evaluated via the Illumina sequencing method. Membrane bioreactors (MBRs) operated with this novel QQ bacterium to evaluate the improvement in the performance of MBR. Anti-biofouling effect of T5 was enhanced as 71% compared to the control reactor. Also, QQ bacteria did not have any negative effect on the removal of organics during the process. Gram-negative bacteria were found to be dominant over Gram-positive bacteria. Proteobacteria, Actinobacteria, Bacteroidetes, Acidobacteria, Firmicutes, and Chloroflexi were dominant phyla in the control and QQ reactors. The proportion of Alphaproteobacteria was most significant among Proteobacteria. The relative abundances of Actinobacteria, Acidobacteria, and Firmicutes were significantly affected by Quorum quenching mechanism. On the other hand, QQ activity of Bacillus sp. T5 significantly influenced the relative abundance of Proteobacteria, Bacteroidetes, and Chloroflexi. The QQ process appeared to generate variations in the structure of the microbial community. According to the results of the molecular analyses, the syntrophic interaction of Bacillus sp. T5 and indigenous Gram-negative and Gram-positive bacterial community is critical to the performance of MBRs.

Effect of metabolic uncoupler, 3,3′,4′,5-tetrachlorosalicylanilide (TCS) on Bacillus subtilis: biofilm formation, flocculability and surface characteristics

In order to understand the inhibitory mechanism of metabolic uncoupler in biofilm, this study investigated the effect of TCS on B. subtilis biofilm formation, flocculability, surface characteristics and thermodynamic properties. An optimal concentration of TCS, a metabolic uncoupler, was observed to substantially inhibit biofilm formation and the secretion of extracellular polymeric substances (EPS). The effect of TCS on the zeta potential and flocculability of bacterial suspension implied the addition of 100 μg L⁻¹ TCS increased the net negative charge of cell surface which induced the reduction of B. subtilis flocculability. Meanwhile, the effects of TCS on bacterial surfacial thermodynamic properties were analyzed by the Derjaguin–Landau–Verwey–Overbeek (DLVO) and extend DLVO (XDLVO) theories. As DLVO and XDLVO predicted, the primary energy barrier between bacterial cells incubated with 100 μg L⁻¹ TCS were increased compared to that of control, indicating that B. subtilis incubated with 100 μg L⁻¹ TCS must consume more energy to aggregate or form biofilm.

This study aimed to investigate the inhibitory mechanism of metabolic uncoupler on biofilm formation through surface characteristics and thermodynamics analysis.