Increased performance and antifouling of mixed-matrix membranes of cellulose acetate with hydrophilic nanoparticles of polydopamine-sulfobetaine methacrylate for oil-water separation

A fucoidan-loaded hydrogel coating for enhancing corrosion resistance, hemocompatibility and endothelial cell growth of magnesium alloy for cardiovascular stents

Although magnesium alloy has received tremendous attention in biodegradable cardiovascular stents, the poor in vivo corrosion resistance and limited endothelialization are still the bottlenecks for its application in cardiovascular stents. Fabrication of the multifunctional bioactive coating with excellent anti-corrosion on the surface is beneficial for rapid re-endothelialization and the normal physiological function recovery of blood vessels. In the present study, a bioactive hydrogel coating was established on the surface of magnesium alloy by copolymerization of sulfobetaine methacrylate (SBMA) and acrylamide (AM) via ultraviolet (UV) polymerization, followed by the immobilization of fucoidan (Fu). The results showed that the as-prepared multifunctional hydrogel coating could enhance the corrosion resistance and the surface wettability of the magnesium alloy surface, endowing it with the ability of selective albumin adsorption; meanwhile, it could augment biocompatibility. The following introduction of fucoidan on the surface could further improve the hemocompatibility characterized by reducing protein adsorption, minimizing hemolysis, and preventing platelet aggregation and activation. Additionally, the immobilized fucoidan promoted endothelial cell (EC) growth, as well as up-regulated the expression of vascular endothelial growth factor (VEGF) and nitric oxide (NO) in endothelial cells (ECs). Consequently, this research paves a novel approach to developing a versatile bioactive coating for magnesium alloy surfaces and lays a foundation in cardiovascular biomaterials.

Cellulose Membranes: Synthesis and Applications for Water and Gas Separation and Purification

Membranes are a selective barrier that allows certain species (molecules and ions) to pass through while blocking others. Some rely on size exclusion, where larger molecules get stuck while smaller ones permeate through. Others use differences in charge or polarity to attract and repel specific species. Membranes can purify air and water by allowing only air and water molecules to pass through, while preventing contaminants such as microorganisms and particles, or to separate a target gas or vapor, such as H2 and CO2, from other gases. The higher the flux and selectivity, the better a material is for membranes. The desirable performance can be tuned through material type (polymers, ceramics, and biobased materials), microstructure (porosity and tortuosity), and surface chemistry. Most membranes are made from plastic from petroleum-based resources, contributing to global climate change and plastic pollution. Cellulose can be an alternative sustainable resource for making renewable membranes. Cellulose exists in plant cell walls as natural fibers, which can be broken down into smaller components such as cellulose fibrils, nanofibrils, nanocrystals, and cellulose macromolecules through mechanical and chemical processing. Membranes made from reassembling these particles and molecules have variable pore architecture, porosity, and separation properties and, therefore, have a wide range of applications in nano-, micro-, and ultrafiltration and forward osmosis. Despite their advantages, cellulose membranes face some challenges. Improving the selectivity of membranes for specific molecules often comes at the expense of permeability. The stability of cellulose membranes in harsh environments or under continuous operation needs further improvement. Research is ongoing to address these challenges and develop advanced cellulose membranes with enhanced performance. This article reviews the microstructures, fabrication methods, and potential applications of cellulose membranes, providing some critical insights into processing-structure-property relationships for current state-of-the-art cellulosic membranes that could be used to improve their performance.

Modification of cellulose substrate by in situ synthesis of metal-organic framework-5 for thin film microextraction of some non-steroidal anti-inflammatory drugs and their measurement by high-performance liquid chromatography-ultraviolet detector

This work, reports the successful preparation a thin film by a simple and inexpensive process for quantification of a model analytes in the urine sample using HPLC-UV. To this end, cellulose paper was employed as a substrate for the in-situ synthesis of MOF-5, to increase the resistance of the prepared film. The prepared film can be reused 26 times with no reduction in its performance. The thin film prepared by MOF-5 modified cellulose substrate was utilized in thin film microextraction (TFME) method for the extraction and preconcentration of naproxen, aspirin, tolmetin, and celecoxib. Under optimal conditions, the linear dynamic range of the target analytes was 2-500 µg L-1 with correlation coefficients (R2) ranging from 0.9961 to 0.9990. Also, the limits of detection (LODs), the limits of quantification (LOQs) and relative standard deviation (RSD%) of the proposed method for selected analytes ranged between 0.57 and 0.77 µg L-1, 1.7 to 2.3 and 3.5 % to 6.2 %, respectively. Moreover, relative recoveries varied from of 94 % to 108 %, indicating the absence of matrices effect in the proposed method. Eventually, the TFME was successfully used for the extraction of selected analytes from urine samples.

Nanocelluloses fine-tuned polyvinylidene fluoride (PVDF) membrane for enhanced separation and antifouling

To mitigate membrane fouling and address the trade-off between permeability and selectivity, we fabricated nanocellulose (NC) fine-tuned polyvinylidene fluoride (PVDF) porous membranes (NC-PVDFs) using phase inversion method through blending NCs with varied aspect ratios, surface charges and grafted functional groups. NC-PVDF presented rougher surface (increased by at least 18.3 %), higher porosity and crystallinity compared to PVDF membrane. Moreover, cellulose nanocrystals incorporated PVDF (CNC-PVDF) elevated membrane surface charge and hydrophilicity (from 74.3° to 71.7°), while 2,2,6,6-tetramethylpiperidine-1-oxyl-oxidized cellulose nanofibers modified PVDF (TCNF-PVDF) enhanced the porosity (from 25.0 % to 40.3 %) and tensile strength (63.6 % higher than PVDF). For separation performance, NC improved flux, rejection and fouling resistance due to facilitation of phase transition thermokinetics as pore-forming agent and increased hydrophilicity at both interface and pore wall. For water flux, NC-PVDFs (139-228 L·m-2·h-1) resulted in increased permeability compared to bare PVDF. CNC-PVDF membrane exhibited the highest water flux because of improved porosity, roughness and hydrophilicity. For bovine serum albumin (BSA) rejection, the removal rates of all NC-PVDFs were all above 90 %. Notably, TCNF-PVDF exhibited the most remarkable elevation of BSA rejection (95.1 %) owing to size exclusion and charge repulsion in comparison with PVDF.

A comprehensive review on state-of-the-art antifouling super(wetting and anti-wetting) membranes for oily wastewater treatment

One of the most dangerous types of pollution to the environment is oily wastewater, which is produced from a number of industrial sources and can cause damage to the environment, people, and creatures. To overcome this issue, membrane technology as an advanced method has been considered for treating oily wastewater due to its stability, high removal efficiency, and simplicity in scaling up. Membrane fouling, or the accumulation of oil droplets at or within the membrane pores, compromises the efficiency of membrane separation and water flux. In the last decade, the fabrication of membranes with specific wettability to reduce fouling has received much consideration. The purpose of this article is to offer a literature overview of all fabricated anti-fouling super(wetting and anti-wetting) membranes for applicable membrane processes for the separation of immiscible and emulsified oil/water mixtures. In this review, we first explain membrane fouling and discuss methods for preventing it. Afterwards, in all membrane separation processes, including pressure-driven, gravity-driven, and thermal-driven, membranes based on the form and density of oil are categorized as oil-removing or water-removing with special wettability, and then their wettability modification with different materials is particularly discussed. Finally, the prospect of anti-fouling membrane fabrication in the future is presented.

Designing of zwitterionic proline hydrogel electrolytes for anti-freezing supercapacitors

Hydrogel electrolytes containing a large amount of freezable water tend to freeze at subzero temperatures, which catastrophically reduces their ionic conductivity and thus limits their practical applications. In this work, we propose a new type anti-freezing hydrogel electrolyte based on an additive of zwitterionic proline, which can maintain high ionic conductivities of hydrogel electrolytes at subzero temperatures. The unique zwitterionic structure leads to several interesting characters like strong hydration, strong ionic interactions and low self-associations, which is proved to be the keys for the high performance of hydrogel electrolytes under low temperatures. As a result, the proline hydrogel electrolytes show a high ionic conductivity of 4.2 mS cm-1 even at -40 °C. The activated carbon electrode of supercapacitors based on proline hydrogel electrolytes delivers high specific capacitances of 145.8 (at 0.5 A g-1) and 116.1 F g-1 (at 0.5 A g-1) at 25 and -30 °C, respectively. Furthermore, the specific capacitance still shows a high retention of 71% after 12,000 charge/discharge cycles at -30 °C, confirming the good low-temperature adaptability. Such anti-freezing electrolytes with high ionic conductivity will open up a new avenue for anti-freezing energy storage devices, not limited to supercapacitors.

Synthesis of novel interpenetrated network for ocular co-administration of timolol maleate and dorzolamide hydrochloride drugs

In the present work, novel interpenetrated networks (IPNs) of [2-(methacryloyloxy)ethyl]dimethyl-(3-sulfopropyl)ammonium hydroxide) (SBMA) and poly(vinyl alcohol) (PVA) were prepared for the ocular co-administration of timolol maleate (TIM) and dorzolamide hydrochloride (DORZ), two drugs widely used for the treatment of glaucoma. The successful polymerization of SBMA, in the presence of PVA, led to the formation of semi-interpenetrated pSBMA-PVA networks (IPNs), in the form of sponges, exhibiting intrinsic antimicrobial properties attributed to SBMA. Fourier-transform infrared spectroscopy (FTIR) was utilized to confirm the successful synthesis of the IPNs. Further assessments, including contact angle and water sorption measurements, highlighted their significant hydrophilicity, a feature that makes them suitable for ocular applications. Differential scanning calorimetry (DSC) measurements indicated that PVA serves as a plasticizer, while an assessment of the water sorption capacity of these materials suggested that although the incorporation of PVA results in slightly less hydrophilic materials, the prepared sponges still remain sufficiently hydrophilic for ocular use. Following their characterization, the optimal pSBMA-PVA IPN was used to encapsulate TIM and DORZ. Irritation tests, performed using the HET-CAM method, confirmed that the drug-loaded sponges were safe and potentially well-tolerated for ophthalmic use. Finally, the co-release study for the two drugs revealed a sustained release pattern in both cases, while drug release from the sponges was primarily controlled by diffusion.

Anatase-cellulose acetate for reinforced desalination membrane with antibacterial properties

This study aimed to prepare antifouling and highly mechanical strengthening membranes for brackish and underground water desalination. It was designed from cellulose acetate (CA) loaded anatase. Anatase was prepared from tetra-iso-propylorthotitanate and carboxymethyl cellulose. Different concentrations of anatase (0.2, 0.3, 0.5, 0.6, 0.7, and 0.8)% were loaded onto CA during the inversion phase preparation of the membranes. The prepared membranes were characterized using Fourier Transform Infrared spectroscopy (FTIR), X-ray diffraction (XRD), thermogravimetric analysis (TGA), scanning electron microscopy (SEM & EDX), mechanical properties, swelling ratio, porosity determination, and ion release. The analysis confirmed the formation of anatase on the surface and inside the macro-voids of the membrane. Furthermore, anatase loading improved the CA membrane's mechanical properties and decreased its swelling and porosity rate. Also, CA-loaded anatase membranes displayed a significant antibacterial potential against Gram-positive and Gram-negative bacteria. The results showed that the salt rejection of the CA/anatase films as-prepared varies considerably with the addition of nanomaterial, rising from 46%:92% with the prepared membranes under the 10-bar operation condition and 5 g/L NaCl input concentration. It can be concluded that the prepared CA-loaded anatase membranes have high mechanical properties that are safe, economical, available, and can stop membrane biofouling.

Improvement of salt rejection efficiency of cellulose acetate membrane through modification by poly(amidoamine) dendrimer-functionalized graphene oxide

In this work, the grafting method using graphene oxide (GO) - poly(amidoamine) dendrimer (PAMAM) nanocomposite as filler for the functionalization of cellulose acetate membrane is reported. Here, cellulose acetate membrane incorporated by nanocomposite in the polymer solution was prepared through the phase inversion technique. The effect of embedding GO-PAMAM on the characterization properties and rejection performance was studied. The results of zeta potential, thermogravimetric analysis (TGA), contact angle measurements, Fourier-transform infrared spectroscopy (FTIR), and field emission scanning electron microscopy (FE-SEM) established successful modification. Based on the data found, adding the filler improves membrane properties. Loading of 1.00 wt% of GO/PAMAM was found to be the optimized amount of the filler in the membrane processing with the highest porosity (74%), antifouling behavior (88%), reversible fouling ratio (45.71%), and the least contact angle (∼40°). Hence, the rejection and permeability tests of the prepared membrane were examined by Na2SO4 (98.40%), NaCl (52%), and MgCl2 (57%) solutions through a lab dead-end cell. According to the results, the value of salt rejection established more permeability and rejection than neat cellulose acetate membrane.

Fluorine-Containing, Self-Assembled Graft Copolymer for Tuning the Hydrophilicity and Antifouling Properties of PVDF Ultrafiltration Membranes

Neat poly(vinylidene fluoride) (PVDF) ultrafiltration (UF) membranes exhibit poor water permeance and surface hydrophobicity, resulting in poor antifouling properties. Herein, we report the synthesis of a fluorine-containing amphiphilic graft copolymer, poly(2,2,2-trifluoroethyl methacrylate)-g-poly(ethylene glycol) behenyl ether methacrylate (PTFEMA-g-PEGBEM), hereafter referred to as PTF, and its effect on the structure, morphology, and properties of PVDF membranes. The PTF graft copolymer formed a self-assembled nanostructure with a size of 7-8 nm, benefiting from its amphiphilic nature and microphase separation ability. During the nonsolvent-induced phase separation (NIPS) process, the hydrophilic PEGBEM chains were preferentially oriented towards the membrane surface, whereas the superhydrophobic PTFEMA chains were confined in the hydrophobic PVDF matrix. The PTF graft copolymer not only increased the pore size and porosity but also significantly improved the surface hydrophilicity, flux recovery ratio (FRR), and antifouling properties of the membrane. The membrane performance was optimal at 5 wt.% PTF loading, with a water permeance of 45 L m-2 h-1 bar-1, a BSA rejection of 98.6%, and an FRR of 83.0%, which were much greater than those of the neat PVDF membrane. Notably, the tensile strength of the membrane reached 6.34 MPa, which indicated much better mechanical properties than those reported in the literature. These results highlight the effectiveness of surface modification via the rational design of polymer additives and the precise adjustment of the components for preparing membranes with high performance and excellent mechanical properties.

Hybrid porous material supported in a cellulose acetate polymeric membrane for the direct immersion thin-film microextraction of parabens in water

A simple and sensitive direct immersion thin-film microextraction (DI-TFME) method based on MIL-101(Cr) modified with carbon nanofibers supported in cellulose acetate (CA-MIL-101(Cr)@CNFs) polymeric membrane was developed for the extraction and preconcentration of parabens in environmental water samples. A high-performance liquid chromatography-diode array detector (HPLC-DAD) was used for the determination and quantification of methylparaben (MP) and propylparaben (PP). The factors affecting the DI-TFME performance were investigated using central composite design (CCD). The linearity of the DI-TFME/HPLC-DAD method obtained under optimal conditions was 0.04-0.04-500 µg/L with a correlation coefficient (R2) greater than 0.99, respectively. The limits of detection (LOD) and quantification (LOQ) for methylparaben were 11 ng/L and 37 ng/L; for propylparaben, they were 13 ng/L and 43 ng/L, respectively. The enrichment factors were 93.7 and 123 for methylparaben and propylparaben. The intraday (repeatability) and interday (reproducibility) precisions expressed as relative standard deviations (%RSD) were less than 5%. Furthermore, the DI-TFME/HPLC-DAD method was validated using real water samples spiked with known concentrations of the analytes. The recoveries ranged from 91.5 to 99.8%, and intraday and interday trueness values were less than ±15%. The DI-TFME/HPLC-DAD approach was effectively used for the preconcentration and quantification of parabens in river water and wastewater samples.

Constructing a composite microfiltration carbon membrane by TiO2 and Fe2O3 for efficient separation of oil-water emulsions

Membrane-based separation technology has attracted enormous attention for oil/water emulsion treatment. Here, composite microfiltration carbon membranes (MCMs) were prepared from the precursor of phenolic resin doping with TiO2 and Fe2O3 via the processes of stereotype and pyrolysis. The functional groups, thermal stability, porous structure, microstructure, morphology, and hydrophilicity of the membrane samples were analyzed by Fourier-transform infrared spectroscopy, thermogravimetric analysis, bubble pressure method, X-ray diffraction, scanning electron microscope, and water contact angle, respectively. The effect of dopant amount on the separation performance of MCMs was investigated. The results show that a mixed matrix system is constructed by TiO2 and Fe2O3 in MCMs, which is beneficial for further optimizing the pore size, porosity, and hydrophilicity of MCMs for oily wastewater treatment by varying the dopant amount. The maximum oil rejections are achieved at 98.9% and 99.6% for MCMs with a dopant content of TiO2 and Fe2O3 at 25%, respectively. In brief, this study offers an attractive strategy for improving the separation performance of MCMs for oily wastewater.

A sustainable layered nanofiber/sheet aerogels enabling repeated life cycles for effective oil/water separation

Discarded oil-containing absorbents, which has been used in handling oil spills, are tricky to deal with and have rose global environmental concerns regarding release of microplastics. Herein, we developed a facile strategy to fabricate sustainable absorbents by a gas-inflating method, through which 2D electrospinning polycaprolactone nanofiber membranes were directly inflated into highly porous 3D nanofiber/sheet aerogels with layered long fiber structure. The membranes were inflated rapidly from a baseline porosity of 81.98% into 97.36-99.42% in 10-60 min. The obtained aerogels were further wrapped with -CH₃ ended siloxane structures using CH₃SiCl₃. This hydrophobic absorbent (CA ≈ 145°) could rapidly trap oils from water with sorption range of 25.60-42.13 g/g and be recycled by simple squeeze due to its mechanical robustness. As-prepared aerogels also showed high separation efficiency to separate oils from both oil/water mixtures and oil-in-water emulsions (>96.4%). Interestingly, the oil-loaded absorbent after cleaning with absolute ethanol could be re-dissolved in selected solvents and promptly reconstituted by re-electrospinning and gas-inflation. The reconstituted aerogels were used as fire-new oil absorbents for repeated life cycles. The novel design, low cost and sustainability of the absorbent provides an efficient and environmentally-friendly solution for handling oil spills.

Fe3O4@Gum Arabic modified polyvinyl chloride membranes to improve antifouling performance and separation efficiency of organic pollutants

Nanofiltration (NF) membranes are promising media for water and wastewater treatment; however, they suffer from their hydrophobic nature and low permeability. For this reason, the polyvinyl chloride (PVC) NF membrane was modified by iron (III) oxide@Gum Arabic (Fe₃O₄@GA) nanocomposite. First, Fe₃O₄@GA nanocomposite was synthesized by the co-precipitation approach and then its morphology, elemental composition, thermal stability, and functional groups were characterized by various analyses. Next, the prepared nanocomposite was added to the casting solution of the PVC membrane. The bare and modified membranes were fabricated by a nonsolvent-induced phase separation (NIPS) method. The characteristics of fabricated membranes were assessed by mechanical strength, water contact angle, pore size, and porosity measurements. The optimum Fe₃O₄@GA/PVC membrane had a 52 L m^-2. h^-1. bar^-1 water flux with a high flux recovery ratio (FRR) value (82%). Also, the filtration experiment exhibited that the Fe₃O₄@GA/PVC membrane could remarkably remove organic contaminants, achieving high rejection rates of 98% Reactive Red-195, 95% Reactive Blue-19, and 96% Rifampicin antibiotic by 0.25 wt% of Fe₃O₄@GA/PVC membrane. According to the results, adding Fe₃O₄@GA green nanocomposite to the membrane casting solution is a suitable and efficient procedure for modifying NF membranes.

Incorporation of 2D-biotene to polyethersulfone ultrafiltration membrane with superhydrophilicity and antifouling properties for removal of organic pollutants

Here, for the first time, one or few-layer exfoliated 2D-Biotene (E-BIT) was prepared by a cost-effective liquid-phase exfoliation of economical and accessible bulk biotite (B-BIT). The successful preparation of E-BIT was further verified by different characterization methods. XRD pattern demonstrated that B-BIT's basal spacing was increased from 10.07 Å to 11.02 Å. Also, the transparency of the E-BIT to the electron beam showed its small thickness after exfoliation, which was confirmed by AFM results, too. This natural material was utilized as an efficient nano-additive to improve the properties of polyethersulfone (PES) polymeric membrane. E-BIT blended membranes with various quantities (0-2 wt%) were prepared via the non-solvent induced phase inversion method. Small holes at the up layer, coarse finger-like holes and macro-voids at the sublayer were seen in asymmetric prepared membranes. Modification caused the improvement of the membranes' hydrophilicity, which the contact angle was reduced from 69.3 to 53.4 for bare PES and 1 wt% E-BIT blended membranes, respectively. 1 wt% E-BIT blended membrane illustrated flux enhancement of 198.8 L/m² h, and high elimination efficiency of bovine serum albumin (99%), reactive red 195 (97.8%), reactive green 9 (93.5%), and reactive blue 19 (88.4%), with improved flux recovery ratio of 73%.

Effect of Filler Types on Cellulose-Acetate-Based Composite Used as Coatings for Biodegradable Magnesium Implants for Trauma

Magnesium alloys are considered one of the most promising materials for biodegradable trauma implants because they promote bone healing and exhibit adequate mechanical strength during their biodegradation in relation to the bone healing process. Surface modification of biodegradable magnesium alloys is an important research field that is analyzed in many publications as the biodegradation due to the corrosion process and the interface with human tissue is improved. The aim of the current preliminary study is to develop a polymeric-based composite coating on biodegradable magnesium alloys by the solvent evaporation method to reduce the biodegradation rate much more than in the case of simple polymeric coatings by involving some bioactive filler in the form of particles consisting of hydroxyapatite and magnesium. Various techniques such as SEM coupled with EDS, FTIR, and RAMAN spectroscopy, and contact angle were used for the structural and morphological characterization of the coatings. In addition, thermogravimetric analysis (TGA) was used to study the effect of filler particles on polymer thermostability. In vitro cytotoxicity assays were performed on MG-63 cells (human osteosarcomas). The experimental analysis highlights the positive effect of magnesium and hydroxyapatite particles as filler for cellulose acetate when they are used alone from biocompatibility and surface analysis points of view, and it is not recommended to use both types of particles (hydroxyapatite and magnesium) as hybrid filling. In future studies focused on implantation testing, we will use only CA-based composite coatings with one filler on magnesium alloys because these composite coatings have shown better results from the in vitro testing point of view for future potential orthopedic biodegradable implants for trauma.

Recent Advances on the Fabrication of Antifouling Phase-Inversion Membranes by Physical Blending Modification Method

Membrane technology is an essential tool for water treatment and biomedical applications. Despite their extensive use in these fields, polymeric-based membranes still face several challenges, including instability, low mechanical strength, and propensity to fouling. The latter point has attracted the attention of numerous teams worldwide developing antifouling materials for membranes and interfaces. A convenient method to prepare antifouling membranes is via physical blending (or simply blending), which is a one-step method that consists of mixing the main matrix polymer and the antifouling material prior to casting and film formation by a phase inversion process. This review focuses on the recent development (past 10 years) of antifouling membranes via this method and uses different phase-inversion processes including liquid-induced phase separation, vapor induced phase separation, and thermally induced phase separation. Antifouling materials used in these recent studies including polymers, metals, ceramics, and carbon-based and porous nanomaterials are also surveyed. Furthermore, the assessment of antifouling properties and performances are extensively summarized. Finally, we conclude this review with a list of technical and scientific challenges that still need to be overcome to improve the functional properties and widen the range of applications of antifouling membranes prepared by blending modification.

Fabrication of Ti2SnC-MAX Phase Blended PES Membranes with Improved Hydrophilicity and Antifouling Properties for Oil/Water Separation

In this research work, the Ti₂SnC MAX phase (MP) was synthesized via the reactive sintering procedure. The layered and crystalline structure of this MP was verified by SEM, HRTEM, and XRD analyses. This nano-additive was used for improvement of different features of the polyethersulfone (PES) polymeric membranes. The blended membranes containing diverse quantities of the MP (0-1 wt%) were fabricated by a non-solvent-induced phase inversion method. The asymmetric structure of the membranes with small holes in the top layer and coarse finger-like holes and macro-voids in the sublayer was observed by applying SEM analysis. The improvement of the membrane's hydrophilicity was verified via reducing the contact angle of the membranes from 63.38° to 49.77° (for bare and optimum membranes, respectively). Additionally, in the presence of 0.5 wt% MP, the pure water flux increased from 286 h to 355 L/m² h. The average roughness of this membrane increased in comparison with the bare membrane, which shows the increase in the filtration-available area. The high separation efficiency of the oil/water emulsion (80%) with an improved flux recovery ratio of 65% was illustrated by the optimum blended membrane.

Novel Magnetic Mixed Cellulose Acetate Matrix Membranes with Oxygen-Enrichment Potential

This work presents novel magnetic mixed cellulose-based matrix membranes that combine the advantages of a low-cost common polymer matrix, such as cellulose acetate (CA), and a low-cost magnetic filler. Moreover, the presented magnetic mixed CA matrix membranes were fabricated and used without applying an external magnetic field during either the membrane casting or the separating process. Poly(methylmethacrylate) and lithium chloride were used in order to improve the mechanical properties and porosity of the fabricated membranes. The iron-nickel magnetic alloys used were prepared through a simple chemical reduction method with unique morphologies (Fe₁₀Ni₉₀-starfish-like and Fe₂₀Ni₈₀-necklace-like). The novel magnetic mixed CA matrix membranes fabricated were characterized using different analysis techniques, including SEM, EDX, XRD, TGA, and FTIR-ATR analyses. Furthermore, the static water contact angle, membrane thickness, surface roughness, tensile strength, and membrane porosity (using ethanol and water) were determined. In addition, vibrating sample magnetometer (VSM) analysis was conducted and the oxygen transition rate (OTR) was studied. The magnetic mixed CA matrix membrane containing starfish-like Fe₁₀Ni₉₀ alloy was characterized by high coercivity (109 Oe) and an efficient 1.271 × 10^-5 cm³/(m²·s) OTR compared to the blank CA membrane with 19.8 Oe coercivity and no OTR. The effects of the polymeric matrix composition, viscosity, and compatibility with the alloys/fillers used on the structure and performance of the fabricated mixed CA matrix membranes compared to the previously used poly(ethersufone) polymeric matrix are discussed and highlighted. The novel magnetic mixed CA matrix membranes presented have good potential for use in the oxygen-enrichment process.

A review on fabrication, characterization of membrane and the influence of various parameters on contaminant separation process

In most developing countries, the availability of drinking water is a major problem. This creates the need for treatment of wastewater, reusability of water, etc. The membrane technology has its place in the market for treating such water. This review compares polymeric membrane fabrication techniques, characteristics, and factors responsible for effective membrane separation for different materials. Although extensive knowledge is available on membrane fabrication, fabricating a membrane is still more challenging, which is more prone to antifouling properties. The competency in different fabrication methods like phase inversion, interfacial polymerization, stretching, track etching and electrospinning are elucidated in the current study. Further, the challenges and adaptability of different application fabrication methods are studied. Important surface parameters like surface wettability, roughness, surface tension, pore size, surface charge, surface functional group and pure water flux are analyzed for different polymeric membranes. In addition, the properties responsible for fouling the membrane are also covered in detail. Flow direction and velocity are the main factors that characterize a membrane's antifouling nature. Antifouling separation can still be achieved by characterizing feed properties such as pH, temperature, diffusivity, ion concentration, and surface content. Understanding fouling properties is a key to progress in membrane technology to develop an effective membrane separation.

A passive-active combined strategy for ultrafiltration membrane fouling control in continuous oily wastewater purification

Membrane-based technology has been confirmed as an effective way to treat emulsified oily wastewater, however, membrane fouling is still one of practical challenges in long-term operation. Herein, a novel passive-active combined strategy was proposed to control membrane fouling in continuous oily wastewater purification, where the δ-MnO₂ decoration layer helped to reduce the total fouling ratio (passive strategy for fouling mitigation) and the catalytic cleaning effectively removed the irreversible oil fouling (active strategy for fouling removal). The functional membrane was prepared via in-situ modification, referred to as δ-MnO₂@TA-PES. The morphology, crystalline phase, chemical structure and surface properties of the membranes were systematically characterized. Compared with PES, the δ-MnO₂@TA-PES possessed superhydrophilicity, enhanced electronegativity and narrowed pore size. The δ-MnO₂@TA-PES achieved high water permeation flux of 723.9 L·m ^- 2·h ^- 1·bar^-1, excellent oil rejection with separation efficiency above 98.5% for various emulsions, and durable anti-oil-fouling performance with FRR_b of 98.0%. Notably, the oil cake layer fouling on δ-MnO₂@TA-PES was greatly alleviated owing to its enhanced surface properties. In addition, δ-MnO₂@TA-PES showed high cleaning efficiency in the peroxymonosulfate (PMS) cleaning process, where the radical and nonradical pathways occurred simultaneously. And the active substances generated in the nonradical process (especially ¹O₂) were considered as the main contributor to the reduction of irreversible fouling. Overall, the novel strategy of fouling control ensured the efficient operation of ultrafiltration membranes for the continuous oily wastewater purification.

Impact of Membrane Modification and Surface Immobilization Techniques on the Hemocompatibility of Hemodialysis Membranes: A Critical Review

Despite significant research efforts, hemodialysis patients have poor survival rates and low quality of life. Ultrafiltration (UF) membranes are the core of hemodialysis treatment, acting as a barrier for metabolic waste removal and supplying vital nutrients. So, developing a durable and suitable membrane that may be employed for therapeutic purposes is crucial. Surface modificationis a useful solution to boostmembrane characteristics like roughness, charge neutrality, wettability, hemocompatibility, and functionality, which are important in dialysis efficiency. The modification techniques can be classified as follows: (i) physical modification techniques (thermal treatment, polishing and grinding, blending, and coating), (ii) chemical modification (chemical methods, ozone treatment, ultraviolet-induced grafting, plasma treatment, high energy radiation, and enzymatic treatment); and (iii) combination methods (physicochemical). Despite the fact that each strategy has its own set of benefits and drawbacks, all of these methods yielded noteworthy outcomes, even if quantifying the enhanced performance is difficult. A hemodialysis membrane with outstanding hydrophilicity and hemocompatibility can be achieved by employing the right surface modification and immobilization technique. Modified membranes pave the way for more advancement in hemodialysis membrane hemocompatibility. Therefore, this critical review focused on the impact of the modification method used on the hemocompatibility of dialysis membranes while covering some possible modifications and basic research beyond clinical applications.

The Application of Cellulose Acetate Membranes for Separation of Fermentation Broths by the Reverse Osmosis: A Feasibility Study

Recently, there has been a special research focus on the bioconversion of glycerol to 1,3-propanediol (1,3-PD) due to its significance in the chemical industry. However, the treatment and separation of fermentation broths is a great challenge. Currently, the reverse osmosis (RO) process is a reliable state-of-the-art technique for separation of biological solutions. This study (as the first to do so) investigated the feasibility of separation of 1,3-PD broths with the use of cellulose acetate (CA) membrane by the RO process. The experiments were carried out using the installation equipped with the plate module, under the transmembrane pressure (TMP) and temperature of 1 MPa and 298 K, respectively. It was found that the used membrane was suitable for broth separation. Indeed, it was noted that 1,3-PD, as a target product, migrated through the membrane; meanwhile, other broth components were rejected in various degrees. Moreover, it was proven that retention of carboxylic acids tended to increase with increasing molecular weight, according to the following order: succinic acid > lactic acid > acetic acid > formic acid. With regards to ions, retention degree increased with the increase of ionic radius and decrease of diffusion coefficient. Finally, it was demonstrated that the CA membrane is resistant to irreversible fouling, which has a positive effect on the economic viability of the process.

Improvement of Antibacterial and Antifouling Properties of a Cellulose Acetate Membrane by Surface Grafting Quaternary Ammonium Salt

Through etherification reaction, epoxy propyl dimethyl dodecyl ammonium chloride (EPDMDAC) was grafted onto the surface of a cellulose acetate (CA) membrane to prepare a stable nonleaching antibacterial antifouling membrane (QCA-X). The results showed that with the extension of grafting reaction time, the quaternary ammonium salt groups on the membrane surface increased and the hydrophilicity was enhanced. Compared with those of the CA membrane, the filtration capacity and antifouling performance of the QCA-X membrane are improved. When the grafting time is 4 h, the water permeability and flux recovery rate of the QCA-4 membrane are increased by 139 and 21.5%, respectively. The QCA-X membrane showed excellent antibacterial performance, and the sterilization rate against S. aureus and E. coli was more than 99.99%. After four repeated antibacterial cycles, the bactericidal rates against S. aureus and E. coli were maintained at about 99.69 ± 0.02 and 99.98 ± 0.02%, respectively, with good antibacterial persistence. Moreover, the QCA-X membrane can effectively inhibit bacterial adhesion. Mild and simple EPDMDAC grafting modifications improve the antibacterial, antifouling, and antibioadhesion properties of the CA membrane, showing its application potential in long-term water treatment, especially in biofouling water treatment.

Bacterial cellulose: A promising biopolymer with interesting properties and applications

The ever-increasing demands for materials with desirable properties led to the development of materials that impose unfavorable influences on the environment and the ecosystem. Developing a low-cost, durable, and eco-friendly functional material with biological origins has become necessary to avoid these consequences. Bacterial cellulose generated by bacteria dispenses excellent structural and functional properties and satisfies these requirements. BC and BC-derived materials are essential in developing pure and environmentally safe functional materials. This review offers a detailed understanding of the biosynthesis of BC, properties, various functionalization methods, and applicability in biomedical, water treatment, food storage, energy conversion, and energy storage applications.

Progress for Co-Incorporation of Polydopamine and Nanoparticles for Improving Membranes Performance

Incorporating polydopamine has become a viable method for membrane modification due to its universality and versatility. Fillers in their different categories have been confirmed as effective elements to improve the properties of membranes such as hydrophilicity, permeability, mechanical strength, and fouling resistance. Thus, this paper mainly highlights the recent studies that have been carried out using polydopamine and nanomaterial fillers simultaneously in modifying the performance of different membranes such as ultrafiltration, microfiltration, nanofiltration, reverse osmosis, and forward osmosis membranes according to the various modification methods. Graphene oxide nanoparticles have recently attracted a lot of attention among different nanoparticles used with polydopamine, due to their impressive characteristics impacts on enhancing membrane hydrophilicity, mechanical strength, and fouling resistance. Thus, the incorporation techniques of graphene oxide nanoparticles and polydopamine for enhancing membranes have been highlighted in this work. Moreover, different studies carried out on using polydopamine as a nanofiller for optimizing membrane performance have been discussed. Finally, perspectives, and possible paths of further research on mussel-inspired polydopamine and nanoparticles co-incorporation are stated according to the progress made in this field. It is anticipated that this review would provide benefits for the scientific community in designing a new generation of polymeric membranes for the treatment of different feed water and wastewater based on adhesive mussel inspired polydopamine polymer and nanomaterials combinations.

Cellulose acetate in fabrication of polymeric membranes: A review

Developing biodegradable polymers to fabricate filtration membranes is one of the main challenges of membrane science and technology. Cellulose acetate (CA) membranes, due to their excellent film-forming property, high chemical and mechanical stability, high hydrophilicity, eco-friendly, and suitable cost, are extensively used in water and wastewater treatment, gas separation, and energy generation purposes. The CA is one of the first materials used to fabricate filtration membranes. However, in the last decade, the possibility of modification of CA to improve permeability and stability has attracted the researcher's attention again. This review is focused on the properties of cellulose derivatives and especially CA membranes in the fabrication of polymeric separation membranes in various applications such as filtration, gas separation, adsorption, and ion exchange membranes. Firstly, a brief introduction of CA properties and used molecular weights in the fabrication of membranes will be presented. After that, different configurations of CA membranes will be outlined, and the performance of CA membranes in several applications and configurations as the main polymer and as an additive in the fabrication of other polymer-based membranes will be discussed.

Alternative methods for cleaning membranes in water and wastewater treatment

Membrane fouling is caused by foulant deposition or adsorption through physical or chemical interactions on the membrane surface, causing the reduction of flux through the membrane. The main drawbacks of chemical agents used for cleaning are cost, damage caused on the membrane, and waste stream making the process unattractive. Alternative, methods such as ultrasound, enzymatic process, and osmotic backwashing were explored for membrane cleaning. Among all mentioned methods, micronanobubbles have been reported as a promising and emergent method for membrane surface cleaning; unfortunately, the information is limited, but preliminary studies have shown it as an efficient, cheap, and environmentally friendly technique. Other methods like electrically and vibratory-enhanced membrane cleaning also could be interesting but currently are unexplored and information is limited. PRACTITIONER POINTS: Chemical cleaning is an efficient option; however, from an environmental point of view, it is not attractive, and high concentrations could cause damage to the membrane. Micronanobubbles are an emergent and suitable technology for membrane and surface cleaning. Membrane modification and functionalization avoid membrane fast fouling, and the cleaning process is easier, but the manufacture cost could be expensive.

Lignocellulosic Biomass-Derived Nanocellulose Crystals as Fillers in Membranes for Water and Wastewater Treatment: A Review

The improvement of membrane applications for wastewater treatment has been a focal point of research in recent times, with a wide variety of efforts being made to enhance the performance, integrity and environmental friendliness of the existing membrane materials. Cellulose nanocrystals (CNCs) are sustainable nanomaterials derived from microorganisms and plants with promising potential in wastewater treatment. Cellulose nanomaterials offer a satisfactory alternative to other environmentally harmful nanomaterials. However, only a few review articles on this important field are available in the open literature, especially in membrane applications for wastewater treatment. This review briefly highlights the circular economy of waste lignocellulosic biomass and the isolation of CNCs from waste lignocellulosic biomass for membrane applications. The surface chemical functionalization technique for the preparation of CNC-based materials with the desired functional groups and properties is outlined. Recent uses of CNC-based materials in membrane applications for wastewater treatment are presented. In addition, the assessment of the environmental impacts of CNCs, cellulose extraction, the production techniques of cellulose products, cellulose product utilization, and their end-of-life disposal are briefly discussed. Furthermore, the challenges and prospects for the development of CNC from waste biomass for application in wastewater treatment are discussed extensively. Finally, this review unraveled some important perceptions on the prospects of CNC-based materials, especially in membrane applications for the treatment of wastewater.

Recent Progress in Microfiltration/Ultrafiltration Membranes for Separation of Oil and Water Emulsions

Oily wastewater has become one of the leading causes of environmental pollution. A massive quantity of oily wastewater is released from industries, oil spills, and routine activities, endangering the ecosystem's sustainability. Due to the enormous negative impact, researchers put strenuous efforts into developing a sustainable solution to treat oily wastewater. Microfiltration/ultrafiltration membranes are considered an efficient solution to treat oily wastewater due to their low cost, small footprint, facile operation, and high separation efficiencies. However, membranes severely fouled during the separation process due to oil's adsorption and cake layer formation, which shortens the membranes' life. This review has critically discussed the microfiltration/ultrafiltration membrane synthesizing methods and their emulsion's separation performance. In the end, key challenges and their possible solutions are highlighted to provide future direction to synthesize next-generation membranes.

Enhanced water flux and bacterial resistance in cellulose acetate membranes with quaternary ammoniumpropylated polysilsesquioxane

An enhanced water flux and anti-fouling nanocomposite ultrafiltration membrane based on quaternary ammoniumpropylated polysilsesquioxane (QAPS)/cellulose acetate (QAPS@CA) was fabricated by in situ sol-gel processing via phase inversion followed by quaternization with methyl iodide (CH₃I). Membrane characterizations were performed based on the contact angle, FTIR, SEM, and TGA properties. Membrane separation performance was assessed in terms of pure water flux, rejection, and fouling resistance. The 7%QAPS@CA nanocomposite membrane showed an increased wettability (46.6° water contact angle), water uptake (113%) and a high pure water permeability of ∼370 L m^-2 h^-1 bar^-1. Furthermore, the 7%QAPS@CA nanocomposite membrane exhibited excellent bactericidal properties (∼97.5% growth inhibition) against Escherichia coli (E. coli) compared to the bare CA membrane (0% growth inhibition). The 7%QAPS@CA nanocomposite membrane can be recommended for water treatment and biomedical applications.

In situ regulation of bacterial cellulose networks by starch from different sources or amylose/amylopectin content during fermentation

Bacterial cellulose (BC) is a promising biopolymer, but its three-dimensional structure needs to be controllable to be used in multiple fields. BC has some advantages over other types of cellulose, not only in terms of purity and properties but also in terms of modification (in situ modification) during the synthesis process. Here, starches from different sources or with amylose/amylopectin content were added to the growth medium to regulate the structural properties of BC in-situ. The obtained BC membranes were further modified by superhydrophobic treatment for oil-water separation. Starches alter the viscosity of the medium, thus affecting bacterial motility and cellulose synthesis, and adhere to the microfibers, limiting their further polymerization and ultimately altering the membrane porosity, pore size, and mechanical properties perpendicular to the BC fibril layer direction. The average pore diameter of the BC/PS membrane increased by 1.94 times compared to the initial BC membrane. The chemically modified BC/PS membrane exhibited super-hydrophobicity (water contact angle 167°), high oil-water separation flux (dichloromethane, 23,205 Lm^-2 h^-1 MPa^-1), high separation efficiency (>97%). The study provides a foundation for developing methods to regulate the network structure of BC and broaden its application.

A Facile Method to Synthesize 3D Pomegranate-like Polydopamine Microspheres

Nanospheres have found versatile applications in the biomedical field; however, their possible harmful effects on immune and inflammatory systems are also a crucial concern. Inspired by a pomegranate structure, we demonstrated a novel structure for the nanostructured microspheres to overcome the drawbacks of nanospheres without compromising their merits. In this study, 3D pomegranate-like polydopamine microspheres (PDAMS) were synthesized by self-oxidative polymerization of dopamine hydrochloride. Herein, controlling the pH during polymerization led to synthesizing homogeneous agglomerated nano-sized spheres (400–2000 nm) and finally forming tunable and monodisperse micron-sized particles (21 µm) with uniform spherical shape porous microstructure. PDAMS interaction with the potential targets, Bone morphogenetic protein-2 (BMP2), Decorin, and Matrilin-1, was investigated via molecular calculations. Theoretical energy analysis revealed that PDAMS interaction with BMP2, Decorin, and Matrilin-1 is spontaneous, so that a protein layer formation on the PDAMS surface suggests application in bone and cartilage repair. It was also observed that PDAMS presented in-vitro degradation within 4 weeks. Here, disappearance of the UV-VIS spectrum peak at 280 nm is accompanied by the degradation of catechol groups. Pomegranate-like PDAMS support the biomimetic formation of hydroxyapatite-like layers, making them appropriate candidates for hard tissue applications. Herein, the appearance of peaks in XRD spectrum at 31.37, 39.57, 45.21, and 50.13° attributed to hydroxyapatite-like layers formation. All these results demonstrated that self-oxidative polymerization under a controllable pH can be a green and straightforward technique for preparing the pomegranate-like PDAMS and providing an innovative basis for further pre-clinical and clinical investigations.