Activated carbon/metal-organic framework composite as a bio-based novel green adsorbent: Preparation and mathematical pollutant removal modeling

Cationic and anionic cross-assisted synergistic photocatalytic removal of binary organic dye mixture using Ni-doped perovskite oxide

Organic dyes present in industrial wastewater are the major contributor to water pollution, which harm human health and the environment. Photocatalytic dye degradation is an effective strategy for water remediation by converting these organic dyes waste into non-harmful by-products. Therefore, in this study, Ni-doped LaFeO3 (NLFO) perovskite nanoparticles were extensively explored for photocatalytic degradation of cationic and anionic dyes and their mixture. The NLFO nanoparticles were successfully synthesized by surfactant assisted hydrothermal method under controlled Ni doping. The X-ray diffraction (XRD) and field emission scanning electron microscope (FESEM) revealed the variation in size (40-70 nm) of orthorhombic crystalline LFO nanoparticles with Ni doping and hence the size of microspheres (0.78. to 1.78 μm). The kinetic studies revealed that the LaFe0·6Ni0·4O3 performed well by providing degradation efficiency of 99.2% in 210 min, 99.1% in 100 min, and 98.4% in 70 min for Crystal Violet (CV), Congo Red (CR), and their mixture with rate constant of 0.019, 0.039, and 0.055 min-1 respectively. The radical scavenger tests indicated the synergetic contributions of O2- and •OH- active radicals in faster degradation of CV and CR dye mixture. The stepwise fragmentation of dye molecule during the photocatalytic degradation identified from the LCMS indicates the degradation of CV dye through de-alkylation and benzene ring breaking, whereas azo bond cleavage and oxidation lead to low molecular weight intermediates for CR dye, which all together helped to degrade their dye mixture (50 mg L-1 and 100 mg L-1) in significantly lesser time (70 min). Overall, the Ni-doped LFO microsphere consisting of nanoparticles acts as a superior catalyst for the more efficient and faster degradation of binary dye mixture.

Magnetic Fe3O4/bamboo-based activated carbon/UiO-66 composite as an environmentally friendly and effective adsorbent for removal of Bisphenol A

The magnetic Fe3O4/bamboo-based activated carbon/Zr-based metal-organic frameworks composite (Fe3O4/BAC/UiO-66) was prepared by hydrothermal method. The as-prepared material was analyzed via TEM, XRD, FT-IR, BET-BJH, VSM and XPS techniques, the results showed that it had good dispersion and magnetic separation capacity (Ms = 44.06 emu∙g-1). Then, the adsorption properties of materials for bisphenol A (BPA) were studied. The results revealed that the removal efficiency of 50 mg·L-1 BPA by 0.1 g of adsorbent can reach 87.18-95% in a wide pH range. Langmuir isotherm model and pseudo-second-order kinetic well fitted the adsorption data. The thermodynamic data indicated that the adsorption process was spontaneous and endothermic. Moreover, BAC as a supporter and UiO-66 as the functional part in the ternary composite may have a synergistic effect, which was beneficial for the removal of contaminants. The Fe3O4/BAC/UiO-66 can be simply separated from the water using its strong magnetism after finish adsorption process, which effectively avoids secondary contamination.

Biogenic adsorbents for removal of drugs and dyes: A comprehensive review on properties, modification and applications

This comprehensive review explores the potential and versatility of biogenic materials as sustainable and environmentally benign alternatives to conventional adsorbents for the removal of drugs and dyes. Biogenic adsorbents derived from plants, animals, microorganisms, algae and biopolymers have bioactive compounds that interact with functional groups of pollutants, resulting in their binding with the sorbent. These materials can be modified mechanically, thermally and chemically to enhance their adsorption properties. Biogenic hybrid composites, which integrate the characteristics of more than one material, have also been fabricated. Additionally, microorganisms and algae are analyzed for their ability to uptake pollutants. Various influential factors that contribute to the adsorption process are also discussed. The challenge, limitations and future prospects for research are reviewed and bridging gap between large scale application and laboratory scale. This comprehensive review, involves a combination of various biogenic adsorbents, going beyond the existing literature where typically only specific adsorbents are reported. The review also covers the isotherms, kinetics, and desorption studies of biogenic adsorbents, providing an improved framework for their effective use in removing pharmaceuticals and dyes from wastewater.

Green and Sustainable Membranes: A review

Membranes are ubiquitous tools for modern water treatment technology that critically eliminate hazardous materials such as organic, inorganic, heavy metals, and biomedical pollutants. Nowadays, nano-membranes are of particular interest for myriad applications such as water treatment, desalination, ion exchange, ion concentration control, and several kinds of biomedical applications. However, this state-of-the-art technology suffers from some drawbacks, e.g., toxicity and fouling of contaminants, which makes the synthesis of green and sustainable membranes indeed safety-threatening. Typically, sustainability, non-toxicity, performance optimization, and commercialization are concerns centered on manufacturing green synthesized membranes. Thus, critical issues related to toxicity, biosafety, and mechanistic aspects of green-synthesized nano-membranes have to be systematically and comprehensively reviewed and discussed. Herein we evaluate various aspects of green nano-membranes in terms of their synthesis, characterization, recycling, and commercialization aspects. Nanomaterials intended for nano-membrane development are classified in view of their chemistry/synthesis, advantages, and limitations. Indeed, attaining prominent adsorption capacity and selectivity in green-synthesized nano-membranes requires multi-objective optimization of a number of materials and manufacturing parameters. In addition, the efficacy and removal performance of green nano-membranes are analyzed theoretically and experimentally to provide researchers and manufacturers with a comprehensive image of green nano-membrane efficiency under real environmental conditions.

Merging Proline:Xylitol Eutectic Solvent in Crosslinked Chitosan Pervaporation Membranes for Enhanced Water Permeation in Dehydrating Ethanol

The scope of this research aims at merging a new deep eutectic mixture (DES) into a biopolymer-based membrane for a pervaporation application in dehydrating ethanol. Herein, an L-proline:xylitol (at 5:1) eutectic mixture was successfully synthesized and blended with chitosan (CS). A complete characterization of the hybrid membranes, in terms of morphology, solvent uptake, and hydrophilicity, has been conducted. As part of their applicability, the blended membranes were assayed for their ability to separate water from ethanolic solutions by means of pervaporation. At the highest temperature (50 °C), a water permeation of ca. 0.46 kg m^-2 h^-1 was acquired, representing a higher permeation than the pristine CS membranes (ca. 0.37 kg m^-2 h^-1). Therefore, CS membranes demonstrated an enhanced water permeation thanks to their blending with the hydrophilic L-proline:xylitol agent, making these membranes a good candidate for other separations containing polar solvents.

Novel modeling and optimization framework for Navy Blue adsorption onto eco-friendly magnetic geopolymer composite

The disproportionate potency of dyes in textile wastewater is a global concern that needs to be contended. The present study comprehensively investigates the adsorption of Navy-Blue dye (NB) onto bentonite clay based geopolymer/Fe₃O₄ nanocomposite (GFC) using novel statistical and machine learning frameworks in the following steps; (1) synthesis and characterization of GFC, (2) experimental testing and modelling of NB adsorption onto GFC following Box-Behnken design and three response surface prediction models namely stepwise regression analysis (SRA), Support vector regression (SVR) and Kriging (KR), (3) parametric, sensitivity, thermodynamic and kinetic analysis of pH, GFC dose and contact time on adsorption performance, and (4) finding global parametric solution of the process using Latin Hypercube, Sobol and Taguchi orthogonal array sampling and combining SRA-SVR-KR predictions with novel hybrid simulated annealing (SA)-desirability function (DF) approach. Under the given testing range, parametric/sensitivity analysis revealed the critical role of pH over others accounting ∼37% relative effect and primarily derived the NB adsorption. The statistical evaluation of models revealed that all models could be utilized for elucidating and predicting the NB removal using GFC, however, SVR accuracy was better among others for this particular work, as the overall computed root mean squared error was only 0.55 while the error frequency counts remained <1 for 90% predictions. GFC showed 86.29% NB removal for the given experimental matrix which can be elevated to 96.25% under optimum conditions. The NB adsorption was found to be physical, spontaneous, favorable and obeyed pseudo-2nd order kinetics. The results demonstrate the suitability of GFC as the promising cost-effective and efficient alternative for the decolourization of urban and drinking water streams and elucidate the potential of machine learning models for accurate prediction & elevation of adsorption processes with less experimentation in water purification applications.

Low-temperature aerobic carbonization and activation of cellulosic materials for Pb2+ removal in water source

Targeting the removal of Pb²⁺ in wastewater, cellulosic materials were carbonized in an aerobic environment and activated via ion exchange. The maximum adsorption capacity reached 243.5 mg/g on an MCC-derived adsorbent activated with sodium acetate. The modified porous properties improved the adsorption capacity. The capacity could be completely recovered five times through elution with EDTA. Because of the negative effects of Ni, Mg, and Ca elements, the adsorption capacities of activated carbonized natural materials were lower than that of pure cellulose. N₂ adsorption measurement showed that the adsorbent had a large specific surface area as well as abundant micropores and 4-nm-sized mesopores. FTIR and surface potential results proved that carboxyl group was generated in the aerobic carbonization, and was deprotonated during ion exchange. This adsorbent consisted of C-C bonds as the building blocks and hydrophilic groups on the surface. XPS results demonstrated that the Pb 4f binding energies were reduced by 0.7-0.8 eV due to the interaction between Pb²⁺ and the activated adsorbent, indicating that the carboxylate groups bonded with Pb²⁺ through coordination interactions. Pseudo-second-order and Elovich kinetic models were well fitted with the adsorption processes on the pristine and activated carbonized adsorbents, indicative of chemisorption on heterogeneous surfaces. The Freundlich expression agreed well with the data measured, and the pristine and activated adsorbents had weak and strong affinities for Pb²⁺, respectively. The Pb²⁺ adsorption process was exothermic and spontaneous, and heat release determined the spontaneity. The adsorption capacity is attributed to the carboxylate groups and pores generated in the aerobic oxidation and ion exchange procedures.

Separation of organic contaminant (dye) using the modified porous metal-organic framework (MIL)

Herein, the porous metal-organic framework (MIL-88B: Materials Institute Lavoisier) was synthesized and identified by FT-IR (Fourier transform infrared), SEM (Scanning Electron Microscopy), EDS (Energy Dispersive X-Ray Spectroscopy), and XRD (X-ray powder diffraction) analyses. Then MIL-88B was modified using 3-aminopropyl trimethoxy silane and presented as NH₂-MIL-88B. The synthesized materials were used to separate direct red dye 23 (DR23) as an organic contaminant from water. The effect of various important factors such as the amount of adsorbent, initial concentration of contaminants, and pH was investigated. The results showed that the modified adsorbent (NH₂-MIL-88B) had a higher adsorption capacity than the row adsorbent (MIL-88B). The amount of dye adsorption is high at lower pH values. The percentage of DR23 dye removal was complete under optimal conditions. Increasing the amount of adsorbent (0.001-0.003 g) and decreasing the pH (2.1-8.1) increases the percentage of dye removal and increasing the concentration of contaminant (50-125 mg/L) reduces the dye removal in the process. Isotherm data showed that the adsorption process followed the Langmuir model. Also, pseudo-first-order, pseudo-second-order, and intraparticle diffusion kinetic models were used to investigate the adsorption kinetics. Dye adsorption followed pseudo-second-order kinetics with correlation coefficient (0.99 <). The results showed that the modified adsorbent could be used as a suitable adsorbent with a high adsorption capacity for dye removal from water.

Clay-polymer nanocomposites for water and wastewater treatment: A comprehensive review

A majority of water pollution or contamination occurs through the discharge of effluents from industries. Wastewater treatment is crucial to protect our water sources from harmful pollutants. Therefore, a number of efforts have been made to tackle this issue by employing different techniques. Clay minerals and polymers are among these materials used extensively in wastewater treatment. While both have their own drawbacks, it is fascinating to discover that they complement each other to overcome most of their limitations. As a result, clay-polymer nanocomposites (CPNs) have been found to be highly efficient in the adsorption of pollutants from water and show promising results to be a long-term candidate for this purpose. In this paper, we discuss about different types of clay and polymers used in the preparation of CPNs. The work also focuses on the different types of clay-polymer nanocomposites, their synthesis and factors affecting their performance such as pH, temperature, contact time, pollutant concentration and adsorbent dose. In addition, the maximum adsorption capacity, mechanism and kinetics of adsorption are highlighted to assess the performance of CPNs. Various studies indicate that CPNs are only a few steps away from becoming one of the best options for wastewater treatment due to their multiple desirable properties.

Electrospun tannin-rich nanofibrous solid-state membrane for wastewater environmental monitoring and remediation

Heavy metal, organic dyes, and bacterial contamination in water endanger human/animals' health, and therefore, the detection, adsorption, and capturing of contaminants are essential for environmental safety. Ligand-rich membranes are promising for sensors, adsorption, and bacterial decontamination. Herein, tannin (TA)-reinforced 3-aminopropyltriethoxysilane (APTES) crosslinked polycaprolactone (PCL) based nanofibrous membrane (PCL-TA-APTES) was fabricated via electrospinning. PCL-TA-APTES nanofibers possess superior thermal, mechanical, structural, chemical, and aqueous stability properties than the un-crosslinked membrane. It changed its color from yellowish to black in response to Fe^2+/3+ ions due to supramolecular iron-tannin network (FeTA) interaction. Such selective sensing has been noticed after adsorption-desorption cycles. Fe³⁺ concentration, solution pH, contact time, and ligand concentration influence FeTA coordination. Under optimized conditions followed by image processing, the introduced membrane showed a colorimetric linear relationship against Fe³⁺ ions (16.58 μM-650 μM) with a limit of detection of 5.47 μM. The PCL-FeTA-APTES membrane could restrain phenolic group oxidation and result in a partial water-insoluble network. The adsorption filtration results showed that the PCL-FeTA-APTES membrane can be reused and had a higher methylene blue adsorption (32.04 mg/g) than the PCL-TA-APTES membrane (14.96 mg/g). The high capture efficiency of nanocomposite against Fe³⁺-based S. aureus suspension than Fe³⁺-free suspension demonstrated that Fe³⁺-bounded bacterium adhered to the nanocomposite through Fe³⁺/TA-dependent biointerface interactions. Overall, high surface area, rich phenolic ligand, porous microstructure, and super-wetting properties expedite FeTA coordination in the nanocomposite, crucial for Fe^2+/3+ ions sensing, methylene blue adsorption-filtration, and capturing of Fe³⁺-bounded bacterium. These multifunctional properties could promise nanocomposite membrane practicability in wastewater and environmental protection.

Adsorption of Magenta Dye on PbO Doped MgZnO: Interpretation of Statistical Physics Parameters Using Double-Layer Models

This article reports the synthesis of PbO doped MgZnO (PbO@MgZnO) by a co-precipitation method, followed by an ultrasonication process. PbO@MgZnO demonstrates a significant adsorption capability toward Magenta Dye (MD). The greatest adsorption capability was optimized by varying parameters such as pH, MD concentration, and adsorbent dose. The kinetics study illustrates that the adsorption of MD on PbO@MgZnO follows the pseudo-second-order. The isotherm study revealed that Langmuir is best fitted for the adsorption, but with little difference in the R² value of Langmuir and Freundlich, the adsorption process cloud be single or multi-layer. The maximum adsorption capacity was found to be 333.33 mg/g. The negative ΔG refers to the spontaneity of MD adsorption on PbO@MgZnO. The steric parameters from statistical physics models also favor the multi-layer adsorption mechanism. As a function of solution temperature, the parameter n pattern has values of n = 0.395, 0.290, and 0.280 for 298, 308, and 318 K, respectively (i.e., all values were below 1). Therefore, horizontal molecule positioning and multiple locking mechanisms were implicated during interactions between MD and PbO@MgZnO active sites.

Facile Preparation and Analytical Utility of ZnO/Date Palm Fiber Nanocomposites in Lead Removal from Environmental Water Samples

This study reports a facile approach for preparing low-cost, eco-friendly nanocomposites of ZnO nanoparticles (NPs) and date palm tree fiber (DPF) as a biomass sorbent. The hypothesis of this research work is the formation of an outstanding adsorbent based on the date palm fiber and ZnO nanoparticles. ZnO NP/DPF nanocomposites were synthesized by mixing the synthesized ZnO NPs and DPF in different mass ratios and evaluating their efficacy in adsorbing Pb2+ from aqueous solutions. The structure and surface morphology of the developed ZnO NP/DPF nanocomposite were critically characterized by XRD, FESEM, and TEM techniques. Compared to ZnO NPs, the ZnO NP/DPF nanocomposites displayed significantly enhanced Pb2+ uptake. Pb2+ adsorption was confirmed via various isotherm and kinetic models and thermodynamics. The computed Langmuir sorption capacity (qm) was found to be 88.76 mg/g (R2 > 0.998), and the pseudo-second-order R2 > 0.999 model was most appropriate for describing Pb2+ adsorption. Impregnating the biomass with ZnO NPs enhanced the spontaneity of the process, and the value (−56.55 kJ/mol) of ΔH displayed the exothermic characteristics of Pb2+ retention. Only the loaded ZnO NP/DPF achieved the removal of a high percentage (84.92%) of Pb2+ from the environmental water sample (seawater). This finding suggests the use of ZnO NP/DPF nanocomposites for removing heavy metals from environmental water samples to purify the samples.

Garlic peel based mesoporous carbon nanospheres for an effective removal of malachite green dye from aqueous solutions: Detailed isotherms and kinetics

Biowaste based nanoadsorbents have gained much attention in the recent times for wastewater decolourization owing to their low cost, high surface area and high adsorption capacities. In the present research, garlic peel based nanoparticles (GCNP) were synthesized at different temperatures by a one step pyrolytic green approach for the effective removal of cationic dye, malachite green from the aqueous medium. The surface properties of Garlic nanoparticles were elucidated by N₂ adsorption- desorption and all the GCNP samples were found to exhibit Type IV(a) isotherm indicating the presence of mesopores in carbon matrix. Using BET calculations, highest surface area (380 m²/g) was obtained for GCNP synthesized at 1000 ^◦C. Characterization of nanoparticles was done by XRD, EDAX, SEM and FTIR studies before and after the dye treatment. Adsorption studies conducted using different parameters like contact time, concentration and pH and dosage of adsorbent showed removal efficiency above 90% for the contact time of 70 min. Best adsorption experimental results were obtained for GCNP synthesized at 1000 °C ascribable to its high surface area, higher total pore volume (0.26 cm²/g) and higher carbon content. Four adsorption isotherm models were used to validate batch equillibrium studies and the results showed data in good agreement with Langmuir and Freundlich isotherms with maximum Langmuir adsorbtion capactiy to be 373.7 mg/g. Kinetic modelling of the data showed best fit with the Pseudo second order model with rate constant value of 48.726 g mg^-1 min^-1. Regenerative studies were conducted conducted upto 6 cycles. Also the GC nanoparticles were tested for their compatibility in membrane form wherein, removal efficiency results were obtained for GCNP anchored in polyvinyl difluoride (PVDF) and polysulfone (PSF) membrane matrix for dye adsorption.

Facile Synthesis of Sustainable Tannin/Sodium Alginate Composite Hydrogel Beads for Efficient Removal of Methylene Blue

To meet the requirement of sustainable development, bio-based adsorbents were developed for the removal of dye contaminant. To improve the adsorption capacity of pure sodium alginate (SA) adsorbent for the removal of methylene blue (MB), aromatic bio-based tannin (Tan) was incorporated through the cross-linking with calcium ion. The obtained Tan/SA composite hydrogel beads were characterized with SEM, FTIR and TG, demonstrating that millimeter-sized beads were obtained through calcium cross-linking with enhanced thermal stability. The maximum capacity (247.2 mg/g) at optimal condition (pH = 12, T = 45 °C) was obtained for the 40%Tan/SA adsorbents, with a removal efficiency of 82.4%. This can be ascribed to the electrostatic attraction between SA and MB, as well as the formation of π–π stacking between Tan and MB. The adsorption process for MB is endothermic, and chemical adsorption, the removal efficiency was exceeded 90% after five cycles.

Adsorption Properties of Modified ATP-RGO Composite Aerogel for Removal of Malachite Green and Methyl Orange from Unitary and Binary Aqueous Solutions

In this paper, the modified attapulgite-reduced graphene oxide composite aerogel (ATP-RGO CA) was prepared by sol-gel method using modified attapulgite as silica source. The removal of the cationic dye malachite green (MG) and azo dye methyl orange (MO) onto ATP-RGO CA from unitary and binary systems was investigated. Morphology and microstructure studies of ATP-RGO CA were investigated by Fourier transform infrared (FTIR), scanning electron microscopy (SEM), X-ray diffraction (XRD), and specific surface area and porosity analysis. Experiments were carried out as a function of pH, contact time, initial dye concentration, and temperature in unitary and binary systems. The adsorption kinetics, isotherms, thermodynamics, and dye desorption were studied in unitary and binary dye systems. The adsorption kinetics was modeled using the pseudo-first-order, pseudo-second-order, and intraparticle diffusion kinetics equations. The equilibrium adsorption data of MG and MO dyes on ATP-RGO CA were analyzed. Thermodynamic parameters of dye adsorption were obtained. In addition, the regeneration of ATP-RGO CA was studied using dye desorption in unitary and binary dye systems. The adsorption kinetics of the dyes followed pseudo-second-order kinetics. The results indicate that the Langmuir model provides the best correlation of the experimental data. The thermodynamic studies showed that the dye adsorption onto ATP-RGO CA was a spontaneous and endothermic reaction. High desorption of MG and MO showed the regeneration of ATP-RGO CA. It can be concluded that ATP-RGO CA is suitable as an adsorbent material to remove MG and MO dyes from unitary and binary systems.

Study on visible light photocatalytic performance of MIL-100(Fe) modified by carbon nanodots

The emerging porous material metal organic framework (MOFs) has caught researchers' attention in the field of photocatalysis. In this study, a visible light-driven carbon nanodots/MIL-100(Fe) photocatalytic material was prepared by in situ synthesis method. The study found that the composite material loaded with 2.5 mg C-dots (2.5-carbon nanodots/MIL-100(Fe)) showed the best tetracycline degradation efficiency with 4.2 times higher than that of MIL-100(Fe) materials in a neutral environment. The superiority of 2.5-carbon nanodots/MIL-100(Fe) in degrading tetracycline is attributed to the fact that C-dots have the ability to act as acceptors and donors of electrons, thus promoting electron transfer and inhibiting electron-hole recombination. Moreover, the 2.5-carbon nanodots/MIL-100(Fe) also showed high stability after five cycles of the photodegradation reaction. The quenching experiment proved that the main active substances that degrade tetracycline were O₂^- and h⁺. The study of carbon nanodots /MIL-100(Fe) composite materials provides new thoughts and methods for the removal of organic pollutants.

CuO@carbon nanofiber as an efficient peroxymonosulfate catalyst for mitigation of organic matter fouling in the ultrafiltration process

Persulfate oxidation has been increasingly integrated with membrane separation for water purification, whereas the oxidizing ability of persulfate is relatively limited, and appropriate activation methods are urgently required. In this work, a novel catalyst of carbon nanofiber (CNF) supported CuO (CuO@CNF) was synthesized for peroxymonosulfate (PMS) activation. The micro-morphology showed that CuO nanoparticles were well dispersed on the CNF support, which solved the agglomeration problem of nanoparticles and improved the catalytic ability. Furtherly, PMS oxidation activated by CuO@CNF was proposed as a pre-processing means for improving ultrafiltration (UF) water purification efficiency and mitigating membrane fouling. The prepared CuO@CNF was more efficient than individual CNF and CuO in activating PMS for the reduction of various typical natural organic matter, improving permeation flux, and mitigating membrane fouling. The fouling control efficiencies were also verified by characterizing the membrane surface functional groups. The CuO@CNF catalyst could signally promote the oxidative capacity by generating a series of reactive oxygen species, thus enhancing the removal of organics with varying species and molecular weight ranges in surface water. With respect to the fouling condition, the specific permeation flux after filtration was improved from 0.25 to 0.61, with the removal rate of reversible fouling resistance reached 89.6%. The fouling mechanism was apparently altered, with both standard and complete blocking dominated throughout the filtration process. The findings are beneficial for the development of new strategies to improve membrane-based water purification efficiency.

A Weed-Derived Hierarchical Porous Carbon with a Large Specific Surface Area for Efficient Dye and Antibiotic Removal

Adsorption is an economical and efficient method for wastewater treatment, and its advantages are closely related to adsorbents. Herein, the Abutilon theophrasti medicus calyx (AC) was used as the precursor for producing the porous carbon adsorbent (PCAC). PCAC was prepared through carbonization and chemical activation. The product activated by potassium hydroxide exhibited a larger specific surface area, more mesopores, and a higher adsorption capacity than the product activated by sodium hydroxide. PCAC was used for adsorbing rhodamine B (RhB) and chloramphenicol (CAP) from water. Three adsorption kinetic models (the pseudo-first-order, pseudo-second-order, and intra-particle diffusion models), four adsorption isotherm models (the Langmuir, Freundlich, Sips, and Redlich–Peterson models), and thermodynamic equations were used to investigate adsorption processes. The pseudo-second kinetic and Sips isotherm models fit the experimental data well. The adsorption mechanism and the reusability of PCAC were also investigated. PCAC exhibited a large specific surface area. The maximum adsorption capacities (1883.3 mg g⁻¹ for RhB and 1375.3 mg g⁻¹ for CAP) of PCAC are higher than most adsorbents. Additionally, in the fixed bed experiments, PCAC exhibited good performance for the removal of RhB. These results indicated that PCAC was an adsorbent with the advantages of low-cost, a large specific surface area, and high performance.

Engineering controllable oxygen vacancy defects in iron hydroxide oxide immobilized on reduced graphene oxide for boosting visible light-driven photo-Fenton-like oxidation

Visible light-driven photo-Fenton-like technology is a promising advanced oxidation process for water remediation, while the construction of effective synergetic system remains a great challenge. Herein, iron hydroxide oxide (α-FeOOH) with controllable oxygen vacancy defects were engineered on reduced graphene oxide (rGO) nanosheets (named as OVs-FeOOH/rGO) through an in-situ redox method for boosting visible light-driven photo-Fenton-like oxidation. By adjusting the pH environment to modulate the redox reaction kinetics between graphene oxide (GO) and ferrous salt precursors, the oxygen vacancy concentration in α-FeOOH could be precisely controlled. With optimized oxygen vacancy defects obtained at pH 5, the OVs-FeOOH/rGO displayed superior photo-Fenton-like performance for Rhodamine B degradation (99% within 40 mins, rate constant of 0.2278 mg^-1 L min^-1) with low H₂O₂ dosage (5 mM), standing out among the reported photo-Fenton-like catalysts. The catalyst also showed excellent reusability, general applicability, and tolerance ability of realistic environmental conditions, which demonstrates great potential for practical applications. The results reveal that moderate oxygen vacancy defects can not only strengthen absorption of visible light and organic pollutants, but also promote the charge transfer to simultaneously accelerate the photogenerated electron-hole separation and Fe(III)/Fe(II) Fenton cycle, leading to the remarkable photo-Fenton-like oxidation performance. This work sheds light on the controllable synthesis and mechanism of oxygen vacancy defects to develop efficient photo-Fenton-like catalysts for wastewater treatment.

Recent advances in removal of Congo Red dye by adsorption using an industrial waste

The Congo Red dye was removed from a simulated textile wastewater solution using fly ash from a local power plant. The characterisation of fly ash was studied in detail by SEM, EDX, XRD, FTIR, BET surface area and TGA techniques. The influence of four parameters (contact time, initial concentration, adsorbent dose, and temperature) was analysed, the results showing that the adsorption capacity depends on these parameters. Thermodynamic and regeneration investigations as well are presented. The fit to pseudo-second-order kinetics models suggests that the removal process is a chemical adsorption. The Langmuir model fitted the experimental data, with a maximum adsorption capacity of 22.12 mg/g. The research is a preliminary case study that highlights that fly ash posed a very good potential as a material for Congo Red dye removal.

Adsorption of Phenol onto Aluminum Oxide Nanoparticles: Performance Evaluation, Mechanism Exploration, and Principal Component Analysis (PCA) of Thermodynamics

The removal of phenolic compounds from aqueous solutions using novel adsorption techniques becomes a key research item. Of those, nanoparticles in particular, the low-cost and the high-strength aluminum oxide nanoparticles showed promising results in pollutant uptake and increase in the adsorption efficiency. This study examined various physicochemical process parameters such as temperature, pH, initial phenol concentration, and adsorbent doses, in addition to the impact of those parameters on the adsorption removal mechanism of phenol. The results highlighted that aluminum oxide nanoparticles successfully exhibited superior phenol removal from an aqueous solution in addition to a high potential regeneration of the consumed nanoparticles by HCl. For the adsorbent mass of 0.5 g, phenol adsorption uptake reached 92%. Kinetic studies performed using several models demonstrated the data best fitting with a pseudo-second-order kinetic model. Examining equilibrium studies of various isotherms, the adsorption data of phenol into aluminum oxide nanoparticles was confirmed to be controlled by film diffusion and best represented by the Langmuir isotherm. The maximum capacity of adsorption was 16.97 mg/g. For thermodynamics studies, the results indicated that the adsorption process can vary between endothermic and exothermic reactions. Such relative differences in heat generation and spontaneity in adsorption processes were demonstrated and confirmed by principal component analysis (PCA). This evidence is key for future investigations for the efficiency of adsorption conditions concerning the contaminant type and adsorbate compounds.

Kinetics and Adsorption Equilibrium in the Removal of Azo-Anionic Dyes by Modified Cellulose

This study introduces a new and bio-friendly adsorbent based on natural and cetyltrimethylammonium chloride (CTAC)-modified adsorbent prepared from wheat straw residues for the removal of Congo red (CR) and tartrazine azo-anionic dyes from aqueous solution. The adsorbent was characterized by thermogravimetric analysis (TGA), calorimetric differential (DSC), scanning electron microscopy with energy-dispersive X-ray spectroscopy (SEM/EDX), and pH point of zero charge (pHPZC) techniques. It was found that decreasing the adsorbent dose and increasing the initial concentration favors the removal of tartrazine and Congo red. Tartrazine adsorption capacities were 2.31 mg/g for the cellulose extracted from wheat residues (WC) and 18.85 mg/g for the modified wheat residue cellulose (MWC) for tartrazine as well as 18.5 mg/g for WC and 19.92 for MWC during Congo red (CR) adsorption, respectively. Increasing the initial and decreasing the adsorbent dose concentration favored the adsorption process. From time effect analysis, it was found that the equilibrium time was reached at 120 min when modified wheat cellulose was used and at 480 min when wheat cellulose was used. The kinetics of adsorption were described by pseudo-second-order in all cases with R2 > 0.95. The obtained data equilibrium from this research was well-fitted by the Freundlich isotherm model.

Potassium permanganate dye removal from synthetic wastewater using a novel, low-cost adsorbent, modified from the powder of Foeniculum vulgare seeds

In this study, Seeds powder of Foeniculum vulgare was used to prepare a novel adsorbent, the modification of the prepared adsorbent was done by each of ZnCl₂, oxalic acid, and CuS, all samples have been characterized by different techniques and examined for Potassium permanganate (KMnO₄) adsorption. Among the four modified and unmodified adsorbents, the sample modified by oxalic acid has the highest percentage removal for KMnO₄ adsorption (%R = 89.36). The impact of KMnO₄ concentration, adsorbent dose, contact temperature, contact time, and solution pH on the adsorption performance was also investigated. The experimental data of this adsorption was analyzed by different kinetic and isotherm models. As Constants of thermodynamic ΔG°, ΔH°, and ΔS° have been also evaluated. Surface area, pore volume, and pore size of the modified oxalic acid F. vulgare seeds powder adsorbent were determined as 0.6806 m² g^-1, 0.00215 cm³ g^-1, and 522.063 Å, as pH_ZPC also was stated to be 7.2. The R² values obtained from applying different isotherm and kinetic models (0.999 and 0.996) showed that the adsorption performance of KMnO₄ follows the Langmuir and Pseudo 2nd order models. Furthermore, high adsorption capacities of 1111.11, 1250.00, and 1428.57 mg g^-1 were achieved at three temperatures that were used in this study. Constants of thermodynamic ΔG°, ΔH°, and ΔS° values indicate chemical and spontaneous adsorption at the adsorbent surface. Therefore, the modified adsorbent can be used to remove KMnO₄ dye from pollutant water samples.

Investigating role of ammonia in nitrogen-doping and suppressing polyselenide shuttle effect in Na-Se batteries

Sodium-ion battery (SIB) has attracted extensive research attention owing to its high theoretical capacity and low cost. Herein, we synthesize bio-waste-derived activated carbon (BAC) through a facile synthesis process followed by selenium loading (using melt-infusion method) to form BAC@Se composites. The synthesized BAC and its composite BAC@Se revealed excellent rate performance, great cycling stability, and good reversibility. The BAC revealed a maximum specific capacity of 257 mAh/g at 20 mA/g current density. The BAC@Se showed the maximum specific capacity of 701 mAh/g at 50 mA/g current density (equivalent to a specific energy of about 1051 WhKg^-1/75 WKg^-1) and good rate performance with 226 mAh/g specific capacity at a high current density of 2500 mA/g. Moreover, the composite revealed good cycling stability by retaining 348 mAh/g capacity at 500 mA/g after 500 cycles. The excellent electrochemical properties were attributed to the unique design of composites, which not only provided the physio-chemically trapped selenium but also ensure the fast kinetics of Na ions through interconnected 3-D channels and high restrain against the dissolution of polyselenides into an electrolyte. This work may shed light on recycling different bio-wastes into energy materials for energy storage devices.

Utilization of shell-based agricultural waste adsorbents for removing dyes: A review

Dye existence in the water body adversely impacts the habitat and the quality of the aquatic system. Considering different physical and chemical methods, adsorption is a propitious substitute for extracting dyes from wastewater specifically due to its performance, high selectivity, less expense, clear operation, and existence in a broad area of experimental circumstances. These benefits are directly linked to the essence of the adsorbent strength used in dye adsorption. In keeping with the principles of green chemistry, the adsorbent materials' accessibility in large amounts that involves easy preparation should boost the effectiveness of the adsorption cycle. Agricultural waste shell-based adsorbent is a novel and better alternative for the expansive adsorbent. This article focuses on the use of a raw and activated adsorbent from agricultural waste shell-based material (on the mitigation of different types of synthetic as well as natural textile dye particles) to find out adsorption capacity based on its operational conditions like pH, dosage, primary concentration of dye, equilibrium time and temperature. Oil palm empty agricultural waste bunch fiber has a maximum adsorption capacity of 393.67 mg/g of Cibacron blue 3G-A dye and Almond shell activated carbon has a maximum adsorption ability of 833.33 mg/g of Methylene Blue dye. Adsorption removal capacity of various raw agricultural wastes and activated agricultural wastes is reviewed. Agricultural waste shell-based adsorbents are a low-cost adsorbent that is a safer alternative to traditional adsorbents.

Antifouling catalytic mixed-matrix membranes based on polyethersulfone and composition-optimized Zn-Cu-Fe-O CWAO catalyst under dark ambient conditions

Besides photocatalysts, novel catalytic wet-air oxidation (CWAO) catalysts capable of operating under mild conditions are a potential candidate to fabricate antifouling filtration membranes. This study optimized the CWAO catalyst consisting of three metal oxide components (ZnO, CuO, and Fe₃O₄) and used it to fabricate composite membranes with PES (polyethersulfone). The catalyst was characterized by methods such as FTIR, BET, XRD, UV-Vis DRS, XPS, ESR. The activity of the catalyst and the composite membranes was tested by the Acid Yellow 42 (AY42) degradation experiments in both cases with and without hydrogen peroxide at room conditions with air aeration. The pure water fluxes of composite membranes were also investigated based on a vacuum filtration system. The major degradation pathways of AY42 by the catalyst were proposed from the DFT (Density Functional Theory) and NBO (Natural Bond Orbital) calculations. The results showed that the optimal catalyst has molar ratios of Zn, Cu, and Fe metal ions of 0.05, 0.588, and 0.362, respectively, with AY42 decomposition efficiency of 88% in 3 h. The main factors affecting the catalytic efficiency of the CWAO catalyst determined from the trapping experiment were e^- and O₂. The results from different materials characterization methods have demonstrated the successful synthesis of the catalyst with a high surface area (103.5 m²/g) and small pore diameters (∼10 nm). The AY42 degradation of composite membranes was stable over five repeated cycles with over 70% efficiency. The pure water fluxes of composite membranes have also been significantly improved and are proportional to catalyst contents.

Experimental and Density Functional Theory Studies on a Zinc(II) Coordination Polymer Constructed with 1,3,5-Benzenetricarboxylic Acid and the Derived Nanocomposites from Activated Carbon

A coordination polymer with the composition C₁₂H₂₀O₁₆Zn₂ (ZnBTC) (BTC = benzene-1,3,5-tricarboxylate) was synthesized under hydrothermal conditions at 120 °C, and its crystal structure was determined using single-crystal X-ray crystallography. First-principles electronic structure investigation of the compound was carried out using the density functional theory computational approach. The highest occupied molecular orbital, the lowest unoccupied molecular orbital, the energy gap, and the global reactivity descriptors of ZnBTC were investigated in both the gas phase and the solvent phase using the implicit solvation model, while the donor-acceptor interactions were studied using natural bond orbital analyses. The results revealed that ZnBTC is more stable but less reactive in solvent medium. The larger stabilization energy E ⁽²⁾ indicates a greater interaction of ZnBTC in the solvent than in the gas phase. Orange peel activated carbon and banana peel activated carbon chemically treated with ZnCl₂ and/or KOH were used to modify the synthesis of ZnBTC to obtain nanocomposites. ZnBTC and the nanocomposites were characterized by powder X-ray diffraction (PXRD), thermogravimetric analysis, and Fourier transform infrared. The specific surface area (S _BET) and the average pore diameter of the materials were determined by nitrogen sorption measurements using the Brunauer-Emmett-Teller (BET) method, while scanning electron microscopy and transmission electron microscopy were used to observe their morphology and particle size, respectively. The PXRD of all the activated carbon materials exhibited peaks at 2θ values of 12.7 and 13.9° corresponding to a d-spacing of 6.94 and 6.32 Å, respectively. The N₂ adsorption-desorption isotherm of the materials are of type II with nanocomposites showing enhanced S _BET compared to the pristine ZnBTC. The results also revealed that activated carbons from the banana peel and the derived nanocomposites exhibited better porous structure parameters than those obtained from orange peel. The degradation efficiency of methyl orange in aqueous solutions using ZnBTC as a photocatalyst was found to be 52 %, while that of the nanocomposites were enhanced up to 79 %.

Advances in decontamination of wastewater using biomass-basedcomposites: A critical review

Contaminant removal from wastewater using natural biosorbents has been widely studied as a suitable and environmentally benign alternative for conventional techniques. Currently, researchers are working on various biomass-based composites for wastewater remediation to improve the performance of natural biosorbents. This review takes into focus a wide range of biomass-based composites like hydrogel composites, metal oxide composites, magnetic composites, polymer composites, carbon nanotubes (CNTs) and graphene composites, metal organic framework composites (MOFs) and clay composites for the removal of various contaminants from wastewater. It is evident from the literature survey that the composite fabrication involves the modification of morphological and textural features of the biomass which results in significant enhancement of adsorption capacity. Apart from this, regeneration of the used biomass-based composite is also studied in depth in order to overcome the problem of solid waste generation. This review would prove to be beneficial for researchers who are currently focusing on the development of cost-effective, easily available, recyclable biomass-based composites with enhanced adsorption capacities for wastewater treatment.