A novel red mud adsorbent for phosphorus and diclofenac removal from wastewater

Upcycling of post-consumer polyethylene terephthalate bottles into aluminum-based metal-organic framework adsorbents for efficient orthophosphate removal

2-Phosphonobutane-1,2,4,-tricarboxylic acid (PBTC) is an orthophosphate compound widely used as an antiscalant chemical and corrosion inhibitor in manufacturing. However, PBTC poses persistent environmental concerns due to its stability and resistance to conventional water treatment. In addressing the issues of PBTC in aquatic systems, Al-based metal-organic frameworks (MOFs) have been developed and applied as sustainable adsorbents. The materials are synthesized from terephthalic acid (TPA) linkers derived from upcycling products of post-consumer polyethylene terephthalate (PET) bottles. The PET-derived linker was prepared using alkaline hydrolysis followed by acidification and employed in forming MIL-53 (Al), with a comparative assessment against the corresponding MOFs made from commercial-grade TPA. The structures and properties of the materials were characterized with microscopic and spectroscopic methods. The synthesized adsorbents achieved a phosphate adsorption capacity of 826 mg/g at pH 5, with kinetics fitting a pseudo-second-order model and isotherm patterns aligning with Langmuir, Freundlich, and Sips models, indicative of diverse adsorption on heterogeneous surfaces. The results highlight the role of electrostatic interactions and hydrogen bonding mechanisms in PBTC adsorption. The eco-friendly materials with high adsorption performance offer an innovative route for sustainable waste management and water purification.

Characterization of phosphate modified red mud-based composite materials and study on heavy metal adsorption

In this paper, Bayer red mud (RM) and lotus leaf powder (LL) were used as the main materials, and KH2PO4 was added to modify the material. Under the condition of high-temperature carbonization, RMLL was prepared and phosphate modified red mud matrix composite (PRMLL) was prepared based on KH2PO4 modification, which can effectively remove Pb2+ from water. The optimum preparation and application conditions were determined through orthogonal experiment: dosage 0.1g, ratio 1:1, and temperature 600 °C. The effects of pH, dosage, and initial concentration on the adsorption of Pb2+ were studied. The pseudo-first-order, pseudo-second-order, and Elovich kinetic models were fitted to the experimental data. It was found that RMLL and PRMLL were more consistent with the pseudo-second-order kinetic model and chemisorption. Langmuir, Freundlich, Timkin, and Dubinin-Radushkevich isothermal adsorption models were used to fit the experimental data. It was found that RMLL and PRMLL were more consistent with Langmuir model. In addition, the maximum adsorption capacity of RMLL and PRMLL was 188.1 mg/g and 213.4 mg/g, respectively. It is larger than the adsorption capacity of their monomers. Therefore, the use of RMLL and PRMLL as the removal of Pb2+ from water is a potential application material.

Innovative biopolyelectrolytes-based technologies for wastewater treatment

Developing eco-friendly, cost-effective, and efficient methods for treating water pollutants has become paramount in recent years. Biopolyelectrolytes (BPEs), comprising natural polymers like chitosan, alginate, and cellulose, have emerged as versatile tools in this pursuit. This review offers a comprehensive exploration of the diverse roles of BPEs in combating water contamination, spanning coagulation-flocculation, adsorption, and filtration membrane techniques. With ionizable functional groups, BPEs exhibit promise in removing heavy metals, dyes, and various pollutants. Studies showcase the efficacy of chitosan, alginate, and pectin in achieving notable removal rates. BPEs efficiently adsorb heavy metal ions, dyes, and pesticides, leveraging robust adsorption capacity and exceptional mechanical properties. Furthermore, BPEs play a pivotal role in filtration membrane techniques, offering efficient separation systems with high removal rates and low energy consumption. Despite challenges related to production costs and property variability, their environmentally friendly, biodegradable, renewable, and recyclable nature positions BPEs as compelling candidates for sustainable water treatment technologies. This review delves deeper into BPEs' modification and integration with other materials; these natural polymers hold substantial promise in revolutionizing the landscape of water treatment technologies, offering eco-conscious solutions to address the pressing global issue of water pollution.

Industrial waste-based adsorbents as a new trend for removal of water-borne emerging contaminants

Emerging contaminants in wastewater are one of the growing concerns because of their adverse effects on human health and ecosystems. Adsorption technology offers superior performance due to its cost-effectiveness, stability, recyclability, and reliability in maintaining environmental and health standards for toxic pollutants. Despite extensive research on the use of traditional adsorbents to remove emerging contaminants, their expensiveness, lack of selectivity, and complexity of regeneration remain some of the challenges. Industrial wastes viz. blast furnace slag, red mud, and copper slag can be used to develop efficacious adsorbents for the treatment of emerging contaminants in water. Advantages of the use of such industrial wastes include resource utilization, availability, cost-effectiveness, and waste management. Nevertheless, little is known so far about their application, removal efficacy, adsorption mechanisms, and limitations in the treatment of emerging contaminants. A holistic understanding of the application of such unique industrial waste-derived adsorbents in removing emerging contaminants from water is need of the hour to transform this technology from bench-scale to pilot and large-scale applications. This review investigates different water treatment techniques associated with industrial waste-based adsorbents derived from blast furnace slag, red mud, and copper slag. Besides, this review provides important insights into the growing trends of utilizing such novel types of adsorbents to remove emerging contaminants from water with an emphasis on removal efficacy, controlling measures, adsorption mechanisms, advantages, and limitations. The present timely review brings the current state of knowledge into a single reference which could be a strong platform for future research in understanding the latest advancements, decision making, and financial management related to the treatment of wastewater using industrial waste-based adsorbents.

Red mud accommodated mesoporous black TiO2 framework with enhanced organic pollutant photodegradation

In this work, black TiO2 (BTiO2) loaded on black red mud (BRM) was successfully prepared with the conversion of Fe2O3 into magnetic Fe3O4 in red mud and the reduction of partial Ti4+ to Ti3+ in TiO2 via the facile sol-gel method and H2 reduction treatment. The obtained low-cost BRM/BTiO2 composites exhibit remarkable photocatalytic degradation toward rhodamine B (91.2%) and tetracycline (83.6%) under visible light irradiation, much better than pristine TiO2. This enhancement is attributed to the narrow bandgap with the desired solar-light excitation, the black color with good solar-light absorption, and the heterojunctions with the efficient separation of photogenerated electron-hole pairs. Moreover, the desired magnetic separation of BRM/BTiO2 composites realizes the recycle and recovery of photocatalysts, favoring practical applications in environment. This work provides a cost-efficiency way to prepare RM-supported TiO2 composites for treating organic pollutants in the wastewater, which is of great significance to the comprehensive utilization of RM waste, the cost saving of the photocatalyst, and the visible-light active enhancement of TiO2.

Rice husk hydrochar prepared by hydrochloric acid assisted hydrothermal carbonization for levofloxacin removal in bioretention columns

Hydrochars are promising adsorbents in pollutant removal for water treatment. Herein, hydrochloric acid (HCl) co-hydrothermally treated hydrochars were prepared from rice husk biomass at 180 °C via a one-step hydrothermal method. Adsorption behaviors of levofloxacin (LVX) on hydrochars were evaluated. The specific surface area and pore volume of the hydrochar synthesized in 5 mol/L HCl (5H-HC) were almost 17 and 8 times of untreated hydrochar, respectively. The 5H-HC sample exhibited the highest LVX adsorption capability at room temperature (107 mg/g). Thermodynamic experimental results revealed that adsorption was a spontaneous endothermic process. Yan model provided the best description of the breakthrough behavior of LVX in bioretention column, indicating that the adsorption on the samples involved several rate-limiting factors including diffusion and mass transfer. The results show that facile HCl co-hydrothermal carbonization of waste biomass can produce novel hydrochars with high LVX adsorption ability.

Highly efficient catalytic ozonation degradation of levofloxacin by facile hydrogenation-modified red mud wastes

Iron-rich red mud (RM) is a potential catalyst. However, as industrial waste, is strongly alkaline, low effectiveness, and safety concerns are problems that cannot be ignored, it is urgent to mine out a reasonable disposal and utilization technology for the waste. In this study, an effective catalyst (H-RM) was obtained by facile hydrogenation heating modification of red mud. Then above-prepared H-RM was applied in the catalytic ozonation degradation of levofloxacin (LEV). The H-RM exhibited more remarkable catalytic activities than the RM in terms of LEV degradation, and the optimal efficiency can reach over 90% within 50 min. The mechanism experiment proved that the concentration of dissolved ozone and hydroxyl radical (•OH) significantly increased, which enhanced the oxidation effect. Hydroxyl radical played a dominant role in the degradation of LEV. In the safety test, it is concluded that the concentration of total hexavalent chromium (total Cr(Ⅵ)) in the H-RM catalyst decreases and the leaching concentration of water-soluble Cr(Ⅵ) in aqueous solution is low. The results indicated that the hydrogenation technique is an available Cr (Ⅵ) detoxification method for RM. Moreover, the H-RM has excellent catalytic stability, which is beneficial to recycling and maintains high activity. This research provides an effective means to fulfill the reuse of industrial waste as an alternative to standard raw materials, and comprehensive utilization of the waste to attain the purpose of treating pollution with wastes.

Adsorption Characteristics of Phosphate Based on Al-Doped Waste Ceramsite: Batch and Column Experiments

Phosphorus widely existing in rainfall and wastewater impacts the water environment. In this study, sludge, cement block, and coal fly ash were employed as ceramsite material to synthesize Al-doped waste ceramsite (Al-ceramsite) for removing phosphate (PO₄^3--P) from aqueous solutions. Batch static adsorption-desorption experiments were designed to investigate the effect of various parameters such as Al-ceramsite dosage, PO₄^3--P concentration, temperature, initial pH, coexisting ions, and desorbents on the removal of PO₄^3--P. Also, the fate of PO₄^3--P removal efficiency in actual rainwater was studied through dynamic adsorption column experiments using Al-ceramsite. Results showed that Al-ceramsite could remove PO₄^3--P efficiently under the optimum parameters as follows: Al-ceramsite dosage of 40 g/L, initial PO₄^3--P concentration of 10 mg/L, temperature of 25 °C, and pH of 5. Besides that, the Al-ceramsite could completely remove PO₄^3--P in actual rainwater, and the effluent PO₄^3--P concentration was lower than the environmental quality standards for surface water Class Ⅰ (0.02 mg/L). The adsorption characteristics of Al-ceramsite on PO₄^3--P by X-ray photoelectron spectroscopy (XPS) were further explained. As a result, ligand exchange and complexation were confirmed as the main PO₄^3--P removal mechanism of Al-ceramsite. Thus, Al-ceramsite was prepared from industrial waste and has shown excellent potential for phosphorus removal in practical applications.

Application of Mesopore-Activated Red Mud for Phosphorus Adsorption

In this paper, the mesopore-activated red mud (M-ARM) was prepared by treating red mud (RM) with acid under an ultrasonic batch and through heat treatment at 750 C. The surface area and adsorption average pore width of M-ARM were calculated and obtained values of 13.408 m2 g-1 and 25.160 nm, respectively. Therefore, the maximum adsorption capacity of M-ARM for phosphorus was $200.85\pm 1.66\text{mg}{\text{g}}^{-1}$ at 318 K and $\text{pH}=5$ . At a low initial concentration (75 mg L-1), the phosphorus removal capacity by M-ARM material was up to $97.09\pm 0.15\%$ at 313 K. With the temperature scales varying from 298 to 313 K, the values of Gibbs free energy change ( $\Delta G°$ ) were negative and also vary from -37.47 to -36.68. The phosphorus adsorption process in an aqueous solution is spontaneous, and this adsorption process was exothermic with enthalpy change $∆{\text{H}}^{\text{o}}=-14.36$ . From the results of investigations and calculations of thermodynamic values, kinetics, and adsorption capacity of materials, we can confirm that the materials in this study had a low-cost and potential material for applications to treat phosphorus-contaminated water. In addition, the adsorption kinetics of this material for phosphorus were also studied and discussed.

Wastewater irrigation: An opportunity for improving soil phosphorus availability; PHREEQC modeling and adsorption studies

Wastewater, an alternative supply of water and nutrients, is being allocated as a priority for human population sustainability in arid and semi-arid regions. This work proposes phosphorus (P), a vital growth-limiting nutrient, adsorption behavior in wastewater irrigated agricultural soils in comparison to non-irrigated soils using laboratory batch experiments. The adsorption mechanism was assessed using different adsorption isotherm models. Saturation indices were modeled, using the hydro-geochemical transport code PHREEQC and MINTEQ geochemical software. Phosphorus buffering parameters were also calculated based on the standard equations. The equilibrium data were well fitted with the Freundlich isotherm model. The physical adsorption mechanism was found based on the calculated isotherm parameters. The maximum adsorption capacity was two times more in non-wastewater irrigated soils than irrigated. Results highlighted the effectiveness of wastewater irrigation in P availability in soil. Based on the PHREEQC modeling data, precipitation of Pb and Zn mineral phases was probable in soils by wastewater influence. Meanwhile, the precipitation of stable calcium phases, that affect the P sorption and/or co-precipitation, in non-wastewater irrigated soils was highlighted in the PHREEQC calculations. The standard buffer capacity (SBC) was 43 and 64 L kg^-1 in wastewater irrigated soils and non-irrigated soils, respectively. Findings of the present study demonstrate the importance of wastewater reuse opportunities for agricultural application, especially soil P availability, and are helpful to minimize the environmental impacts of wastewater and solid waste.

A review of comprehensive utilization of red mud

Red mud (RM) is a solid waste generated during the process of alumina production. RM has already posed a serious environmental threat with the development of the alumina refining industry. The comprehensive utilization of RM has attracted much attention due to its large-scale generation and harmful nature. This paper introduces the characteristics and state of RM and summarizes the relevant research on the comprehensive utilization of RM. The results show that comprehensive utilization of RM is mainly focused on the preparation of building materials, the extraction of valuable metals, catalyst synthesis and environmental protection. Besides, the article discusses the existing problems while utilizing RM. Prospects and suggestions for different utilization methods of RM are proposed.

Experimental Investigation on Red Mud from the Bayer Process for Cemented Paste Backfill

Red mud is a by-product of alumina production, and its disposal can have severe environmental consequences. This study experimentally investigates the feasibility of using red mud from the Bayer process for cemented paste backfill (CPB). Different binders and activators were used to improve the mechanical properties, water resistance, and environmental behaviors of red mud-based CPB. In addition, water immersion tests were introduced, for the first time, to evaluate the water resistance of CPB. Furthermore, the environmental behaviors of red mud-based CPB were investigated by conducting leaching experiments. The results showed that the red-mud specimens had an unconfined compressive strength (UCS) of less than 0.2 MPa and disintegrated after being immersed in water. Different binders significantly improved the mechanical properties of red mud-based CPB. In addition, the specimens with different binders showed excellent water resistance, and the softening coefficient of CPB with different binders could exceed 0.7 after being cured for 28 days. The binders exhibited a substantial inhibitory effect on the leaching of hazardous substances in red mud under the solidification and stabilization effects. The leaching concentration of hexavalent chromium, selenium, fluoride, arsenic, lead, and vanadium was reduced by more than 70%. Therefore, this study provides an effective method for the environmental-friendly and large-scale utilization of red mud from the Bayer process.

Crystalline Violet Wastewater Treatment by Low-Temperature Plasma Combined with Industrial Solid Waste Red Mud

Low-temperature plasma (LTP) technology has been successfully used to treat persistent organic pollutants in water. Efforts have been devoted to combine catalysts and LTP to improve the degradation efficiency of pollutants and energy utilization efficiency. Herein, industrial solid waste red mud as a novel catalyst was added to an LTP system to treat crystalline violet (CV) wastewater. The energy yield at 50% CV decomposition and TOC after a 30 min reaction by the plasma treatment, red mud adsorption, and red mud/plasma treatment were compared. The effects of the main operating parameters, such as red mud dosing amount, initial pH, discharge voltage, and initial concentration of CV, on the removal efficiency of CV were investigated. The best degradation of CV was achieved with a red mud dosage of 2 g, a neutral environment, and a discharge voltage of 22 kV. When the red mud was recycled three times, the removal efficiency decreased a little in the red mud/plasma system. Hydroxyl radical plays an important role in the treatment of CV. The red mud was characterized by BET, SEM, XRD, and FT-IR, and the structure of the red mud was not greatly affected after being used in the red mud/plasma system.

Sustainable adsorbents for the removal of pharmaceuticals from wastewater: A review

Over the previous three decades, the worldwide use of pharmaceuticals has surged by more than 2.5 times. Although being considered essential to save many lives, pharmaceuticals have also emerged as a large source of complex environmental contaminants in recent decades. Consequently, the pharmaceuticals and their breakdown products are ending up into the water bodies thus progressively contaminating them and the surrounding environments. Based on recent studies concentrations in water sources are typically >0.1 μg/l and the concentration in treated water is typically >0.05 μg/l. These pharma drugs are removed from aquatic systems by processes such as oxidation, Ultraviolet degradation, reverse osmosis and nano-filtration. However, hazardous sludge creation, incomplete removal, expensive capital and operating costs, and the need for professional operating and maintenance personnel have all limited the economic sustainability of these systems. As a result, the presence of pharmaceuticals in water necessitates even more advanced technologies of purification to harvest clean water, yet present approaches are constrained by their high costs, low reusability, and disposal issues. Here, we review sustainable adsorbents for the removal of pharmaceuticals from wastewater. In this comprehensive review, an evaluation of water contamination caused by pharmaceutical compounds is discussed. An overview of current research on the employment of sustainable adsorbents for the removal of the major pharmaceuticals prevalent in water sources. Numerous aspects of high adsorption efficiencies of these pharmaceutical compounds with such sustainable adsorbents were observed; however, other factors, such as adsorbent regeneration and cost evaluation, must be taken into account in order to assess the true applicability of adsorbents.

Recovery, regeneration and sustainable management of spent adsorbents from wastewater treatment streams: A review

Adsorption is the most widely adopted, effective, and reliable treatment process for the removal of inorganic and organic contaminants from wastewater. One of the major issues with the adsorption-treatment process for the removal of contaminants from wastewater streams is the recovery and sustainable management of spent adsorbents. This review focuses on the effectiveness of emerging adsorbents and how the spent adsorbents could be recovered, regenerated, and further managed through reuse or safe disposal. The critical analysis of both conventional and emerging adsorbents on organic and inorganic contaminants in wastewater systems are evaluated. The various recovery and regeneration techniques of spent adsorbents including magnetic separation, filtration, thermal desorption and decomposition, chemical desorption, supercritical fluid desorption, advanced oxidation process and microbial assisted adsorbent regeneration are discussed in detail. The current challenges for the recovery and regeneration of adsorbents and the methodologies used for solving those problems are covered. The spent adsorbents are managed through regeneration for reuse (such as soil amendment, capacitor, catalyst/catalyst support) or safe disposal involving incineration and landfilling. Sustainable management of spent adsorbents, including processes involved in the recovery and regeneration of adsorbents for reuse, is examined in the context of resource recovery and circular economy. Finally, the review ends with the current drawbacks in the recovery and management of the spent adsorbents and the future directions for the economic and environmental feasibility of the system for industrial-scale application.

Adsorption of inorganic and organic phosphorus onto polypyrrole modified red mud: Evidence from batch and column experiments

The ubiquitous presence of inorganic and organic phosphorus in wastewater and natural water bodies has deteriorated the water environment qualities and exerted significant influences on ecosystems. In this study, an effective polypyrrole modified red mud adsorbent (PRM) was optimized for the adsorptive removal of inorganic and organic phosphorus from aqueous solutions. The addition of ferric chloride and pyrrole was optimized for complete oxidation and modification of polypyrrole onto red mud. Kinetic studies illustrated that the adsorption progress was accomplished by physical and chemical adsorption. The experimental data of the optimized PRM were described well by Langmuir isotherm, and the equilibrium adsorption capacity was 32.9 and 54.7 mg/g for inorganic and organic phosphorus, respectively. The PRM showed commendable adsorption performance despite the pH conditions ranging from 3 to 11. From the effect of ion strength and X-ray photoelectron spectroscopy (XPS) tests, we found that ligand exchange is the main mechanism of orthophosphate adsorption onto PRM, while electrostatic attraction played an important role in organic phosphorus adsorption. The adsorption performance from column studies showed that the velocity of flow influenced the breakthrough time of the column but the initial concentration had minor impacts. This study would extend the potential application of polypyrrole modified red mud, acting as an efficient adsorbent for inorganic and organic phosphorus adsorption in water treatment.

Anionic Dye Removal by Polypyrrole-Modified Red Mud and Its Application to a Lab-Scale Column: Adsorption Performance and Phytotoxicity Assessment

In this study, polypyrrole-modified red mud (PRM) was prepared for the efficient removal of anionic dyes (methyl orange and Congo red) from aqueous solutions. The phytotoxicity (bean sprouts) of the dye solution before and after dye removal was investigated. Adsorption kinetics confirmed that the adsorption of methyl orange (MO) and Congo red (CR) on PRM was controlled by chemical reactions between the functional groups of polypyrrole and dyes. From Langmuir isotherm fitting, we found the theoretical adsorption capacities of MO and CR on PRM were 194.1 and 314.9 mg/g, respectively. The adsorption progress of MO and CR on PRM was found to be spontaneous and endothermic. The column studies demonstrated that, under dynamic flow, the PRM can efficiently remove MO and CR from aqueous solution, with adsorption capacities of 31.08 and 55.04 mg/g, respectively. In the toxicity test, the phytotoxicity of the column effluents (after dye removal) was significantly lowered compared to the initial dye influents. After the removal of MO and CR, the average root length of bean sprouts was increased from 3.30 cm to 5.18 cm and from 3.01 cm to 7.00 cm, respectively. These findings highlighted the efficient removal of dyes by PRM from aqueous solution, demonstrating the possible application of PRM for the removal of dye from dye-contaminated wastewaters.

Efficient removal of nitrogen and phosphorus in aqueous solutions using modified water treatment residuals-sodium alginate beads

A high-performance sorbent, modified water treatment residuals-sodium alginate beads (WTR-SA beads), was prepared through a series of salt and combined thermal roasting composite modification between water treatment residuals and sodium alginate. The properties of modified WTR-SA beads composites were characterized by SEM-EDS, FT-IR, XRD, and BET. The adsorption performance of WTR-SA beads was investigated in removing nitrogen and phosphorus from wastewater. Compared to the unmodified WTR, the removal efficiency of nitrogen and phosphorus onto the modified WTR-SA beads was increased from 22.34 and 77.13% to 95.14 and 98.31%, respectively. The adsorption capacities of nitrogen and phosphorus onto the modified WTR-SA beads were reach a maximum of 2.52 mg/g and 6.45 mg/g, respectively. The adsorption behavior can be well described using a quasi-second-order kinetic model and Langmuir isotherm model. The thermodynamic properties of nitrogen adsorption indicated that the adsorption was spontaneous and exothermic. On the contrary, the adsorption process of phosphorus is an endothermic reaction. The adsorption of nitrogen by modified WTR-SA beads is mainly carried out through ion exchange and hydroxyl complexation, and ion exchange plays a major role in it. While, the adsorption of modified WTR-SA beads on phosphorus is affected by three actions: ligand exchange, chemical precipitation, and ion exchange, which ligand exchange is the main effect. Based on these results, it can be concluded that the modified WTR-SA beads are a high efficiency adsorbent for removing nitrogen and phosphorus from domestic and industrial wastewater.

Reduced Red Mud as the Solar Absorber for Solar-Driven Water Evaporation and Vapor-Electricity Generation

The emergent solar-driven water evaporation technology provides a reassuring scheme for red mud (RM) utilization in environment and materials science. With fewer restrictions on raw materials, wide availability of sheer quantity, and high complexity in chemical composition, the RM may be a promising candidate for solar absorbers. Here, we developed a novel solar absorber with reduced RM. It features favorable light absorption and photothermal conversion ability using biomass pyrolysis. When added to the polyvinyl alcohol and chitosan gel substrate, the light absorptance can reach 94.65%, while the corresponding evaporation rate is as high as 2.185 kg m^-2 h^-1 under an illumination density of 1 kW m^-2. We further demonstrated its potential as an efficient solar absorber in the solar-driven water evaporation and the thermoelectric device to realize the stable and efficient coproduction of vapor and electricity.