Development of injectable biocomposites from hyaluronic acid and bioactive glass nano-particles obtained from different sol–gel routes

Effects of liquid-to-solid ratio and gamma irradiation on the rheology and cytocompatibility of a beta-tricalcium phosphate-based injectable bone substitute

Injectable bone substitute (IBS) materials are commonly used to fill irregular-shaped bone voids in non-load-bearing areas and can offer greater utility over those which are in prefabricated powder, granule, or block forms. This work investigates the impact of liquid-to-solid ratio (LSR) on the rheology and cytocompatibility of IBSs formulated from bioactive glass particles and β-tricalcium phosphate (β-TCP) in glycerol and poly(ethylene glycol) (PEG). IBS formulations of varying LSR were prepared and packed in 3 cc open-bore syringes and sterilized via gamma irradiation (10 kGy, 25 kGy). Gamma-irradiated formulations with high PEG content required the highest (73 N) mechanical force for injection from syringes. Oscillatory viscosity measurements revealed that the viscosity of samples was directly proportional to glycerol content. PEG and glycerol displayed competing effects on the washout resistance and cohesiveness of samples, which were based on total weight loss in media and Ca2+ ion release, respectively. Cell viability in 24-h extracts of 10 kGy gamma-sterilized and 25 kGy gamma-irradiated samples were 22.94% and 56.53%, respectively. The research highlights the complex interplay of IBS components on IBS rheology and, moreover, the cytotoxicity behaviors of beta-tricalcium phosphate-based injectable bone substitutes by in vitro experiments.

Antioxidant flavonoid-loaded nano-bioactive glass bone paste: in vitro apatite formation and flow behavior

Non-cement pastes in the form of injectable materials have gained considerable attention in non-invasive regenerative medicine. Different osteoconductive bioceramics have been used as the solid phase of these bone pastes. Mesoporous bioactive glass can be used as an alternative bioceramic for paste preparation because of its osteogenic qualities. Plant-derived osteogenic agents can also be used in paste formulation to improve osteogenesis; however, their side effects on physical and physicochemical properties should be investigated. In this study, nano-bioactive glass powder was synthesized by a sol-gel method, loaded with different amounts of quercetin (0, 100, 150, and 200 μM), an antioxidant flavonoid with osteogenesis capacity. The loaded powder was then homogenized with a mixture of hyaluronic acid and sodium alginate solution to form a paste. We subsequently evaluated the rheological behavior, injectability, washout resistance, and in vitro bioactivity of the quercetin-loaded pastes. The washout resistance was found to be more than 96% after 14 days of immersion in simulated body fluid (SBF) as well as tris-buffered and citric acid-buffered solutions at 25 °C and 37 °C. All pastes exhibited viscoelastic behavior, in which the elastic modulus exceeded the viscous modulus. The pastes displayed shear-thinning behavior, in which viscosity was more influenced by angular frequency when the quercetin content increased. Results indicated that injectability was much improved using quercetin and the injection force was in the range 20-150 N. Following 14 days of SBF soaking, the formation of a nano-structured apatite phase on the surfaces of quercetin-loaded pastes was confirmed through scanning electron microscopy, X-ray diffractometry, and Fourier-transform infrared spectroscopy. Overall, quercetin, an antioxidant flavonoid osteogenic agent, can be loaded onto the nano-bioactive glass/hyaluronic acid/sodium alginate paste system to enhance injectability, rheological properties, and bioactivity.

Self-adaptable calcium-based bioactive phosphosilicate-infused gelatin-hyaluronic hydrogel for orthopedic regeneration

Bone regeneration is a critical and intricate process vital for healing fractures, defects, and injuries. Although conventional bone grafts are commonly used, they may fall short of optimal outcomes, thereby driving the need for alternative therapies. This research endeavors to explore synergistically designed Hyalo Glass Gel (HGG), and its explicitly for bone tissue engineering and regenerative medicine. The HGG composite comprises a modifiable calcium-based bioactive phosphosilicates-incorporated/crosslinked gelatin-hyaluronic scaffold showcasing promising functional characteristics. The study underscores the distinct attributes of each constituent (gelatin (Gel), hyaluronic acid (HA), and 45S5 calcium sodium phosphosilicates (BG)), and their cooperative influences on the scaffold's performance. Careful manipulation of crosslinking methods facilitates customization of HGG's mechanical attributes, degradation kinetics, and structural features, aligning them with the requisites of bone tissue engineering applications. Moreover, the integration of BG augments the scaffold's bioactivity, thereby expediting tissue regenerative processes. This comprehensive evaluation encompasses HGG's physicochemical aspects, mechanical traits rooted in viscoelasticity, as well as its biodegradability, in-vitro bioactivity, and interactions with stem cells. The result obtained underscores the viscoelastic nature of HGG, substantiating its capacity to foster mesenchymal stem cell viability, proliferation, and differentiation. Significantly, HGG manifests biocompatibility and adjustable attributes, exhibits pronounced drug (vancomycin) retention abilities, rendering it apt for wound healing, drug delivery, and bone regeneration. Its distinctive composition, tailored attributes, and mimicry of bone tissue's extracellular matrix (ECM) due to its bioactive nature, collectively situate its potential as a versatile biomaterial for subsequent research and development endeavors with compelling prospects in bone tissue engineering and regenerative medicine.

Evaluation of biocomposite putty with strontium and zinc co-doped 45S5 bioactive glass and sodium hyaluronate

The application of powder or granule formed bioactive glasses in the defect area with the help of a liquid carrier to fill the defects is a subject of interest and is still open to development. In this study, it was aimed to prepare biocomposites of bioactive glasses incorporating different co-dopants with a carrier biopolymer and to create a fluidic material (Sr and Zn co-doped 45S5 bioactive glasses‑sodium hyaluronate). All biocomposite samples were pseudoplastic fluid type, which may be suitable for defect filling and had excellent bioactivity behaviors confirmed by FTIR, SEM-EDS and XRD. Biocomposites with Sr and Zn co-doped bioactive glass had higher bioactivity considering the crystallinity of hydroxyapatite formations compared to biocomposite with undoped bioactive glasses. Biocomposites with high bioactive glass content had hydroxyapatite formations with higher crystallinity compared to biocomposites with low bioactive glass. Furthermore, all biocomposite samples showed non-cytotoxic effect on the L929 cells up to a certain concentration. However, biocomposites with undoped bioactive glass showed cytotoxic effects at lower concentrations compared to biocomposites with co-doped bioactive glass. Thus, biocomposite putties utilizing Sr and Zn co-doped bioactive glasses may be advantageous for orthopedic applications due to their specified rheological, bioactivity, and biocompatibility properties.

Injectable bone cements: What benefits the combination of calcium phosphates and bioactive glasses could bring?

Out of the wide range of calcium phosphate (CaP) biomaterials, calcium phosphate bone cements (CPCs) have attracted increased attention since their discovery in the 1980s due to their valuable properties such as bioactivity, osteoconductivity, injectability, hardening ability through a low-temperature setting reaction and moldability. Thereafter numerous researches have been performed to enhance the properties of CPCs. Nonetheless, low mechanical performance of CPCs limits their clinical application in load bearing regions of bone. Also, the in vivo resorption and replacement of CPC with new bone tissue is still controversial, thus further improvements of high clinical importance are required. Bioactive glasses (BGs) are biocompatible and able to bond to bone, stimulating new bone growth while dissolving over time. In the last decades extensive research has been performed analyzing the role of BGs in combination with different CaPs. Thus, the focal point of this review paper is to summarize the available research data on how injectable CPC properties could be improved or affected by the addition of BG as a secondary powder phase. It was found that despite the variances of setting time and compressive strength results, desirable injectable properties of bone cements can be achieved by the inclusion of BGs into CPCs. The published data also revealed that the degradation rate of CPCs is significantly improved by BG addition. Moreover, the presence of BG in CPCs improves the in vitro osteogenic differentiation and cell response as well as the tissue-material interaction in vivo.

•

Properties of injectable calcium phosphate bone cements and bioactive glasses are discussed.

•

Benefits that BG addition to CPC could bring are highlighted.

•

Desirable injectable properties of bone cements can be achieved by the inclusion of BGs into CPCs.

•

The presence of BG in CPC advances in vitro and in vivo response of the composites.

•

Future research direction of BG containing injectable CPC composites are provided.

Injectable nanocomposite hydrogels as an emerging platform for biomedical applications: A review

Hydrogels have attracted much attention for biomedical and pharmaceutical applications due to the similarity of their biomimetic structure to the extracellular matrix of natural living tissues, tunable soft porous microarchitecture, superb biomechanical properties, proper biocompatibility, etc. Injectable hydrogels are an exciting type of hydrogels that can be easily injected into the target sites using needles or catheters in a minimally invasive manner. The more comfortable use, less pain, faster recovery period, lower costs, and fewer side effects make injectable hydrogels more attractive to both patients and clinicians in comparison to non-injectable hydrogels. However, it is difficult to achieve an ideal injectable hydrogel using just a single material (i.e., polymer). This challenge can be overcome by incorporating nanofillers into the polymeric matrix to engineer injectable nanocomposite hydrogels with combined or synergistic properties gained from the constituents. This work aims to critically review injectable nanocomposite hydrogels, their preparation methods, properties, functionalities, and versatile biomedical and pharmaceutical applications such as tissue engineering, drug delivery, and cancer labeling and therapy. The most common natural and synthetic polymers as matrices together with the most popular nanomaterials as reinforcements, including nanoceramics, carbon-based nanostructures, metallic nanomaterials, and various nanosized polymeric materials, are highlighted in this review.

Hyaluronic-Acid-Based Organic-Inorganic Composites for Biomedical Applications

Applications of natural hyaluronic acid (HYH) for the fabrication of organic-inorganic composites for biomedical applications are described. Such composites combine unique functional properties of HYH with functional properties of hydroxyapatite, various bioceramics, bioglass, biocements, metal nanoparticles, and quantum dots. Functional properties of advanced composite gels, scaffold materials, cements, particles, films, and coatings are described. Benefiting from the synergy of properties of HYH and inorganic components, advanced composites provide a platform for the development of new drug delivery materials. Many advanced properties of composites are attributed to the ability of HYH to promote biomineralization. Properties of HYH are a key factor for the development of colloidal and electrochemical methods for the fabrication of films and protective coatings for surface modification of biomedical implants and the development of advanced biosensors. Overcoming limitations of traditional materials, HYH is used as a biocompatible capping, dispersing, and structure-directing agent for the synthesis of functional inorganic materials and composites. Gel-forming properties of HYH enable a facile and straightforward approach to the fabrication of antimicrobial materials in different forms. Of particular interest are applications of HYH for the fabrication of biosensors. This review summarizes manufacturing strategies and mechanisms and outlines future trends in the development of functional biocomposites.

Enhancing Mechanical Properties and Biological Performances of Injectable Bioactive Glass by Gelatin and Chitosan for Bone Small Defect Repair

Bioactive glass (BG) represents a promising biomaterial for bone healing; here injectable BG pastes biological properties were improved by the addition of gelatin or chitosan, as well as mechanical resistance was enhanced by adding 10 or 20 wt% 3-Glycidyloxypropyl trimethoxysilane (GPTMS) cross-linker. Composite pastes exhibited bioactivity as apatite formation was observed by Scanning Electron Microscopy (SEM) and X-Ray Diffraction (XRD) after 14 days immersion in simulated body fluid (SBF); moreover, polymers did not enhance degradability as weight loss was >10% after 30 days in physiological conditions. BG-gelatin-20 wt% GPTMS composites demonstrated the highest compressive strength (4.8 ± 0.5 MPa) in comparison with the bulk control paste made of 100% BG in water (1.9 ± 0.1 MPa). Cytocompatibility was demonstrated towards human mesenchymal stem cells (hMSC), osteoblasts progenitors, and endothelial cells. The presence of 20 wt% GPTMS conferred antibacterial properties thus inhibiting the joint pathogens Staphylococcus aureus and Staphylococcus epidermidis infection. Finally, hMSC osteogenesis was successfully supported in a 3D model as demonstrated by alkaline phosphatase release and osteogenic genes expression.

A Review of Bioactive Glass/Natural Polymer Composites: State of the Art

Collagen, gelatin, silk fibroin, hyaluronic acid, chitosan, alginate, and cellulose are biocompatible and non-cytotoxic, being attractive natural polymers for medical devices for both soft and hard tissues. However, such natural polymers have low bioactivity and poor mechanical properties, which limit their applications. To tackle these drawbacks, collagen, gelatin, silk fibroin, hyaluronic acid, chitosan, alginate, and cellulose can be combined with bioactive glass (BG) nanoparticles and microparticles to produce composites. The incorporation of BGs improves the mechanical properties of the final system as well as its bioactivity and regenerative potential. Indeed, several studies have demonstrated that polymer/BG composites may improve angiogenesis, neo-vascularization, cells adhesion, and proliferation. This review presents the state of the art and future perspectives of collagen, gelatin, silk fibroin, hyaluronic acid, chitosan, alginate, and cellulose matrices combined with BG particles to develop composites such as scaffolds, injectable fillers, membranes, hydrogels, and coatings. Emphasis is devoted to the biological potentialities of these hybrid systems, which look rather promising toward a wide spectrum of applications.

Complexation of Injectable Biphasic Calcium Phosphate with Phosphoserine-Presenting Dendrons with Enhanced Osteoregenerative Properties

Injectable biphasic calcium phosphates have been proposed as a solution in the treatment of a range of clinical applications including as fillers in the augmentation of osteoporotic bone. To date, various biodegradable natural or synthetic organics have been used as a polymer component of bone materials to increase their cohesiveness. Herein, a novel bone material was developed combining osteoconductive biphasic calcium phosphate (BCP) nanoparticles with phosphoserine-tethered generation 3 poly(epsilon-lysine) dendron (G3-K PS), a class of hyperbranched peptides previously shown to induce biomineralization and stem cell osteogenic differentiation. Strontium was also incorporated into the BCP nanocrystals (SrBCP) to prevent bone resorption. Within 24 h, an antiwashout behavior was observed in G3-K PS-integrated pure BCP group (BCPG3). Moreover, both in vitro tests by relevant cell phenotypes and an in vivo tissue regeneration study by an osteoporotic animal bone implantation showed that the integration of G3-K PS would downregulate Cxcl9 gene and protein expressions, thus enhancing bone regeneration measured as bone mineral density, new bone volume ratio, and trabecular microarchitectural parameters. However, no synergistic effect was found when Sr was incorporated into the BCPG3 bone pastes. Notably, results indicated a concomitant reduction of bone regeneration potential assessed as reduced Runx2 and PINP expression when bone resorptive RANKL and CTX-I levels were reduced by Sr supplementation. Altogether, the results suggest the potential of injectable BCPG3 bone materials in the treatment of osteoporotic bone defects.

The synergistic effects of SrF2 nanoparticles, YSZ nanoparticles, and poly-ε-l-lysin on physicomechanical, ion release, and antibacterial-cellular behavior of the flowable dental composites

Resin-based pit-and-fissure sealants (flowable resin composites) were formulated using bisphenol-A-glycerolatedimethacrylate (Bis-GMA)-triethylene glycol dimethacrylate-(TEGDMA)-diurethanedimethacrylate (UDMA) mixed monomers and multiple fillers, including synthetic strontium fluoride (SrF₂) nanoparticles as a fluoride-releasing and antibacterial agent, yttria-stabilized zirconia (YSZ) nanoparticles as an auxiliary filler, and poly-ε-l-lysin (ε-PL) as an auxiliary antibacterial agent. Based on the physical, mechanical and initial antibacterial properties, the formulated nano-sealant containing 5 wt% SrF₂, 5 wt% YSZ and 0.5 wt% ε-PL was selected as the optimal specimen and examined for ion release and cytotoxicity. The results showed an average release rate of 0.87 μg·cm^-2·day^-1 in the aqueous medium (pH 6.9) and 1.58 μg·cm^-2·day^-1 in acidic medium (pH 4.0). The maximum cytotoxicity of 20% toward human bone marrow mesenchymal stem cells (hMSCs) was observed according to the 3-(4,5-dimethylthiazol-2-yl)-2,5-diphenyl-tetrazolium bromide (MTT) cytotoxicity assay and acridine orange staining test. A synergy between SrF₂ nanoparticles and ε-PL exhibited a better antibacterial activity in terms of colony reduction compared to the other samples. However, the inclusion of SrF₂ and ε-PL caused mechanically weakening of the sealants that was partly compensated by incorporation of YSZ nanoparticles (up to 10 wt%).

Evaluation of hMSCs Response to Sodium Alginate / Bioactive Glass Composite Paste: Effect of CaO/P2O5, Sodium Alginate Concentration and P/L Ratios

Background:

Bioactive glasses with different compositions have been extensively used as bone tissue engineering. Preparation, development and characterization of alginate pastes containing bioglass for bone repair applications were the purposes of this study.

Objective:

The injectable bone pastes were produced from sol-gel derived bioactive glass nanoparticles with various CaO/P2O5 ratios of 19, 9.5 and 4.75 and sodium alginate solutions with different concentrations of 1, 2 and 4 wt.%. The effect of CaO/P2O5 and powder to liquid (P/L) ratios and alginate concentration on injectability, biodegradation, rheological properties, bioactivity and cellular behavior of the pastes have been studied. The behavior of human mesenchymal stem cells (hMSCs) in the presence of the pastes was assessed by MTT assay, biomineralization assay, ALP activity, Acridine orange staining and Alizarin red staining tests.

Results:

By adding sodium alginate, the pastes exhibited a thixotropy behavior. The storage modulus of all pastes was larger than the loss modulus in the frequency range of 0.1-100 s-1. Cytotoxicity evaluation results revealed that there was a critical amount of bioactive glass in pastes which are above the limit; the viability of hMSCs will be at risk. The pastes made of bioactive glass nanoparticles with CaO/P2O5 = 9.5 and sodium alginate 1% with P/L ratio of 0.8 showed optimum behavior in terms of mineral carrying capacity, injectability characteristics, accellular bioactivity in SBF, loss weight and wash out behavior, proliferation and differentiation of hMSCs.

Conclusion:

According to the results, the pastes prepared with sodium alginate solution and bioactive glass nanoparticles can be beneficial in bone tissue engineering.

Study on an injectable biomedical paste using cross-linked sodium hyaluronate as a carrier of hydroxyapatite particles

Exploring the long-term filler for minimally invasive plastic surgery has been widely concerned. In the present study, a series of injectable paste composed of hydroxyapatite (HAp) spherical particles and cross-linked sodium hyaluronate (cHA) solution were prepared. The physicochemical properties of cHA as a carrier of high content HAp microspheres (>50%) and as-obtained injectable HAp/cHA paste were studied. The cross-linking degree (DC), viscosity and molecular weight (Mw and Mn) of cHA increased with the increasing of the cross-linker dosage from 7.5 to 17.5 wt% under the certain conditions. HAp/cHA pastes were fabricated by homogeneously blending different sizes of HAp microspheres with cHA solution. The stability, rheological performance and push-out force of the pastes were studied, and the influence factors were discussed. The results indicated that moderate crosslinked cHA with 60% middle size HAp (HAp-M60/cHA-15.0) had appropriate comprehensive property. Finally, the in vitro cell culture approved the paste had no cytotoxicity. Although the biological performance of the pastes still need to be investigated, this preliminary study demonstrates that it is possible to carry high content HAp in cHA, expecting the better volumetric maintenance after long term implantation.

Copper-containing mesoporous bioactive glass nanoparticles as multifunctional agent for bone regeneration

The application of mesoporous bioactive glasses (MBGs) containing controllable amount of different ions, with the aim to impart antibacterial activity, as well as stimulation of osteogenesis and angiogenesis, is attracting an increasing interest. In this contribution, in order to endow nano-sized MBG with additional biological functions, the framework of a binary SiO₂-CaO mesoporous glass was modified with different concentrations of copper ions (2 and 5%mol.), through a one-pot ultrasound-assisted sol-gel procedure. The Cu-containing MBG (2%mol.) showed high exposed surface area (550m²g^-1), uniform mesoporous channels (2.6nm), remarkable in vitro bioactive behaviour and sustained release of Cu²⁺ ions. Cu-MBG nanoparticles and their ionic dissolution extracts exhibited antibacterial effect against three different bacteria strains, E. coli, S. aureus, S. epidermidis, and the ability to inhibit and disperse the biofilm produced by S. epidermidis. The obtained results suggest that the developed material, which combines in single multifunctional agent excellent bioactivity and antimicrobial ability, offers promising opportunities for the prevention of infectious diseases and the effective treatment of bone defects.

STATEMENT OF SIGNIFICANCE

In order to endow mesoporous bioactive glass, characterized by excellent bioactive properties, with additional biological functions, Cu-doped mesoporous SiO₂-CaO glass (Cu-MBG) in the form of nanoparticles was prepared by an ultra-sound assisted one pot synthesis. The analysis of the bacterial viability, using different bacterial strains, and the morphological observation of the biofilm produced by the Staphylococcus epidermidis, revealed the antimicrobial effectiveness of the Cu-MBG and the relative ionic extracts against both the bacterial growth and the biofilm formation/dispersion, providing a true alternative to traditional antibiotic systemic therapies. The proposed multifunctional agent represents a promising and versatile platform for bone and soft tissues regeneration.

Antibacterial-nanocomposite bone filler based on silver nanoparticles and polysaccharides

Injectable bone fillers represent an attractive strategy for the treatment of bone defects. These injectable materials should be biocompatible, capable of supporting cell growth and possibly able to exert antibacterial effects. In this work, nanocomposite microbeads based on alginate, chitlac, hydroxyapatite and silver nanoparticles were prepared and characterized. The dried microbeads displayed a rapid swelling in contact with simulated body fluid and maintained their integrity for more than 30 days. The evaluation of silver leakage from the microbeads showed that the antibacterial metal is slowly released in saline solution, with less than 6% of silver released after 1 week. Antibacterial tests proved that the microbeads displayed bactericidal effects toward Staphylococcus aureus, Pseudomonas aeruginosa and Staphylococcus epidermidis, and were also able to damage pre-formed bacterial biofilms. On the other hand, the microbeads did not exert any cytotoxic effect towards osteoblast-like cells. After characterization of the microbeads bioactivity, a possible means to embed them in a fluid medium was explored in order to obtain an injectable paste. Upon suspension of the particles in alginate solution or alginate/hyaluronic acid mixtures, a homogenous and time-stable paste was obtained. Mechanical tests enabled to quantify the extrusion forces from surgical syringes, pointing out the proper injectability of the material. This novel antibacterial bone filler appears as a promising material for the treatment of bone defects, in particular when possible infections could compromise the bone-healing process. Copyright © 2016 John Wiley & Sons, Ltd.

Rheological evaluations and in vitro studies of injectable bioactive glass-polycaprolactone-sodium alginate composites

Composite pastes composed of various amounts of melt-derived bioactive glass 52S4 (MG5) and polycaprolactone (PCL) microspheres in sodium alginate solution were prepared. Rheological properties in both rotatory and oscillatory modes were evaluated. Injectability was measured as injection force versus piston displacement. In vitro calcium phosphate precipitation was also studied in simulated body fluid (SBF) and tracked using scanning electron microscopy, X-ray diffraction and FTIR analyses. All composite pastes were thixotropic in nature and exhibited shear thinning behavior. The magnitude of thixotropy decreased by adding 10-30 wt% PCL, while further amounts of PCL increased it again. Moreover, the composites were viscoelastic materials in which the elastic modulus was higher than viscous term. The pastes which were just made of MG5 or PCL had poor injectability, whereas the composites containing both of these constituents exhibited reasonable injectability. All pastes revealed adequate structural stability in contact with SBF solution. In vitro calcium phosphate precipitation was well observed on the paste made of MG5 and somewhat on the pastes with 10-40 wt% PCL, however the precipitated layer was amorphous in nature. Overall, the produced composites may be appropriate as injectable biomaterials for non-invasive surgeries but more biological evaluations are essential.

Photocurable bioactive bone cement based on hydroxyethyl methacrylate-poly(acrylic/maleic) acid resin and mesoporous sol gel-derived bioactive glass

This paper reports on strong and bioactive bone cement based on ternary bioactive SiO2-CaO-P2O5 glass particles and a photocurable resin comprising hydroxyethyl methacrylate (HEMA) and poly(acrylic/maleic) acid. The as-cured composite represented a compressive strength of about 95 MPa but it weakened during soaking in simulated body fluid, SBF, qua its compressive strength reached to about 20 MPa after immersing for 30 days. Biodegradability of the composite was confirmed by reducing its initial weight (~32%) as well as decreasing the molecular weight of early cured resin during the soaking procedure. The composite exhibited in vitro calcium phosphate precipitation in the form of nanosized carbonated hydroxyapatite, which indicates its bone bonding ability. Proliferation of calvarium-derived newborn rat osteoblasts seeded on top of the composite was observed during incubation at 37 °C, meanwhile, an adequate cell supporting ability was found. Consequently, it seems that the produced composite is an appropriate alternative for bone defect injuries, because of its good cell responses, high compressive strength and ongoing biodegradability, though more in vivo experiments are essential to confirm this assumption.

Strong and Biostable Hyaluronic Acid-Calcium Phosphate Nanocomposite Hydrogel via in Situ Precipitation Process

Hyaluronic acid (HAc) hydrogel exhibits excellent biocompatibility, but it has limited biomedical application due to its poor biomechanical properties as well as too-fast enzymatic degradation. In this study, we have developed an in situ precipitation process for the fabrication of a HAc-calcium phosphate nanocomposite hydrogel, after the formation of the glycidyl methacrylate-conjugated HAc (GMHA) hydrogels via photo-cross-linking, to improve the mechanical and biological properties under physiological conditions. In particular, our process facilitates the rapid incorporation of calcium phosphate (CaP) nanoparticles of uniform size and with minimal agglomeration into a polymer matrix, homogeneously. Compared with pure HAc, the nanocomposite hydrogels exhibit improved mechanical behavior. Specifically, the shear modulus is improved by a factor of 4. The biostability of the nanocomposite hydrogel was also significantly improved compared with that of pure HAc hydrogels under both in vitro and in vivo conditions.

Timing of calcium nitrate addition affects morphology, dispersity and composition of bioactive glass nanoparticles

Bioactive glass nanoparticles (BGN) are promising materials for a number of biomedical applications.

Injectable and self-healing dynamic hydrogel containing bioactive glass nanoparticles as a potential biomaterial for bone regeneration

Combination of Au-based dynamic hydrogel with 100 nm bioactive glass nanoparticles resulted in the formation of an injectable, self-healing and biocompatible hydrogel nanocomposites with osteoinductive properties and potential for bone regeneration.

Design of biocomposite materials for bone tissue regeneration

Several synthetic scaffolds are being developed using polymers, ceramics and their composites to overcome the limitations of auto- and allografts. Polymer-ceramic composites appear to be the most promising bone graft substitute since the natural bone itself is a composite of collagen and hydroxyapatite. Ceramics provide strength and osteoconductivity to the scaffold while polymers impart flexibility and resorbability. Natural polymers have an edge over synthetic polymers because of their biocompatibility and biological recognition property. But, very few natural polymer-ceramic composites are available as commercial products, and those few are predominantly based on type I collagen. Disadvantages of using collagen include allergic reactions and pathogen transmission. The commercial products also lack sufficient mechanical properties. This review summarizes the recent developments of biocomposite materials as bone scaffolds to overcome these drawbacks. Their characteristics, in vitro and in vivo performance are discussed with emphasis on their mechanical properties and ways to improve their performance.

Injectable Bioactive Glass/Polysaccharide Polymers Nanocomposites for Bone Substitution

nanobioactive glasses are biocompatible and osteoconductive materials which can be mixed with solution of biocompatible polymers to make nanobiocomposite paste for hard and even soft tissue treatment. In this study, bioactive glass based on CaO-SiO2-P2O5 system was produced via sol-gel technique and mixed with a solution phase. The solution phase was a 1:1 mixture of 3% hyaluronic acid solution and 3% sodium alginate solution in v/v. Rheological behaviors of the paste in rotation and oscillation modes were measured. For surface reactivity measurements, the paste was immersed in simulated body fluid (SBF) for different intervals and then characterized by SEM. The paste exhibited a superior injectability even from syringes with too narrow tips. It was a thixotropic fluid with shear thinning behavior. The results of surface reactivity revealed precipitation of apatite phase on the paste surfaces meanwhile an appropriate structural stability was observed against disintegration (anti-washout behavior). It seems that this biocomposite paste is an appropriate alternative for injectable bone substitute materials.

Evaluation Nanostructure Properties of Bioactive Glass Scaffolds for Bone Tissue Engineering

The use of biomaterials in bone tissue engineering newly has been developed. They are biocompatible material which are reabsorbed in body and replaced with newly formed tissue. Bioactive glass scaffolds will be appropriate candidates if pore morphology, size and structures are controlled. Scaffolds with nanostructure will provide these goals. In this research bioglass powder was synthesized with sol-gel method to achieve nanostructure powder. The glass powder was characterized with transmission electron microscope (TEM). Scaffolds were prepared with combination of bioglass powder and sugar as porogen followed by pressing at 80 MPa then sintering at 1050 oC. The morphology of sintered scaffolds was characterized with scanning electron microscope (SEM) and porosity was measured with density method. Mechanical properties were assessed with compressive strength. The TEM results show that synthesized powder has particle size about 25 nm. The SEM results show that nanopores and macropores are connectively distributed in whole part of scaffolds. The compressive strength of scaffolds was 0.8 MPa. Overall, the scaffold is suggested that is appropriate alternative for bone tissue engineering.