Removal of basic dye from aqueous solution using tree fern as a biosorbent

Tetracycline adsorption/desorption by raw and activated Tunisian clays

Clay-based adsorbents have applications in environmental remediation, particularly in the removal of emerging pollutants such as antibiotics. Taking that into account, we studied the adsorption/desorption process of tetracycline (TC) using three raw and acid- or base-activated clays (AM, HJ1 and HJ2) collected, respectively, from Aleg (Mazzouna), El Haria (Jebess, Maknessy), and Chouabine (Jebess, Maknessy) formations, located in the Maknessy-Mazzouna basin, center-western of Tunisia. The main physicochemical properties of the clays were determined using standard procedures, where the studied clays presented a basic pH (8.39-9.08) and a high electrical conductivity (446-495 dS m-1). Their organic matter contents were also high (14-20%), as well as the values of the effective cation exchange capacity (80.65-97.45 cmolckg-1). In the exchange complex, the predominant cations were Na and Ca, in the case of clays HJ1 and AM, while Mg and Ca were dominant in the HJ2 clay. The sorption experimental setup consisted in performing batch tests, using 0.5 g of each clay sample, adding the selected TC concentrations, then carrying out quantification of the antibiotic by means of HPL-UV equipment. Raw clays showed high adsorption potential for TC (close to 100%) and very low desorption (generally less than 5%). This high adsorption capacity was also present in the clays after being activated with acid or base, allowing them to adsorb TC in a rather irreversible way for a wide range of pH (3.3-10) and electrical conductivity values (3.03-495 dS m-1). Adsorption experimental data were studied as regards their fitting to the Freundlich, Langmuir, Linear and Sips isotherms, being the Sips model the most appropriate to explain the adsorption of TC in these clays (natural or activated). These results could help to improve the overall knowledge on the application of new low-cost methods, using clay based adsorbents, to reduce risks due to emerging pollutants (and specifically TC) affecting the environment.

Comprehensive Investigation of Cu2+ Adsorption from Wastewater Using Olive-Waste-Derived Adsorbents: Experimental and Molecular Insights

This study investigates the efficacy of adsorbents from locally sourced olive waste-encompassing olive skins, leaves, and pits, recovered from the initial centrifugation of olives (OWP)-and a composite with sodium alginate (OWPSA) for the removal of Cu2+ ions from synthetic wastewater. Experimental analyses conducted at room temperature, with an initial Cu2+ concentration of 50 mg/L and a solid/liquid ratio of 1 g/L, showed that the removal efficiencies were approximately 79.54% and 94.54% for OWP and OWPSA, respectively, highlighting the positive impact of alginate on adsorption capacity. Utilizing statistical physics isotherm models, particularly the single-layer model coupled to real gas (SLMRG), allowed us to robustly fit the experimental data, providing insights into the adsorption mechanisms. Thermodynamic parameters affirmed the spontaneity and endothermic nature of the processes. Adsorption kinetics were interpreted effectively using the pseudo-second-order (PSO) model. Molecular modeling investigations, including the conductor-like screening model for real solvents (COSMO-RS), density functional theory (DFT), and atom-in-molecule (AIM) analysis, unveiled intricate molecular interactions among the adsorbent components-cellulose, hemicellulose, lignin, and alginate-and the pollutant Cu2+, confirming their physically interactive nature. These findings emphasize the synergistic application of experimental and theoretical approaches, providing a comprehensive understanding of copper adsorption dynamics at the molecular level. This methodology holds promise for unraveling intricate processes across various adsorbent materials in wastewater treatment applications.

Nanocellulose: A comprehensive review investigating its potential as an innovative material for water remediation

Rapid growth in industrialization sectors, the wastewater treatment plants become exhausted and potentially not able to give desirable discharge standards. Many industries discharge the untreated effluent into the water bodies which affects the aquatic diversity and human health. The effective disposal of industrial effluents thus has been an imperative requirement. For decades nanocellulose based materials gained immense attraction towards application in wastewater remediation and emerged out as a new biobased nanomaterial. It is light weighted, cost effective, mechanically strong and easily available. Large surface area, versatile surface functionality, biodegradability, high aspect ratio etc., make them suitable candidate in this field. Majorly cellulose based nanomaterials are used in the form of cellulose nanocrystals (CNCs), cellulose nanofibers (CNFs), or bacterial nanocellulose (BNC). This review specifically describes about a variety of extraction methods to produced nanocellulose and also discusses the modification of nanocellulose by adding functionalities in its surface chemistry. We majorly focus on the utilization of nanocellulose based materials in water remediation for the removal of different contaminants such as dyes, heavy metals, oil, microbial colony etc. This review mainly emphasizes in ray of hope towards nanocellulose materials to achieve more advancement in the water remediation fields.

Biosorption of zinc (II) from synthetic wastewater by using Inula Viscosa leaves as a low-cost biosorbent: Experimental and molecular modeling studies

The use of biosorption as a strategy for lowering the amount of pollution caused by heavy metals is particularly encouraging. In this investigation, a low-cost and efficient biosorbent, Inula Viscosa leaves were used to remove zinc ions (Zn²⁺) from synthetic wastewater. A Fourier transform infrared spectroscopy experiment, a scanning electron microscopy experiment, and an energy dispersive X-ray spectroscopy experiment were used to describe the support. Several different physicochemical factors, such as the beginning pH value, contact duration, initial zinc concentration, biosorbent dose, and temperature, were investigated in this study. When the Langmuir, Freundlich, Temkin, Toth, and Redlich-Peterson models were used to match the data from the Inula Viscosa leaves biosorption isotherms, it was found that the biosorption isotherms correspond most closely with the Langmuir isotherm. On the other hand, the kinetic biosorption process was investigated using pseudo-first-order, pseudo-second-order (PS2), and Elovich models. The PS2 model was the one that provided the most accurate description of the biosorption kinetics. The thermodynamics process shows the spontaneous and endothermic character of Zn²⁺ sorption on Inula Viscosa leaves, which also entails the participation of physical interactions. In addition, the atom-in-molecule analysis, density functional theory, and the conductor like screening model for real solvents, were used to investigate the relationship that exists between quantum calculations and experimental outcomes.

Adsorption and removal of ethidium bromide from aqueous solution using optimized biogenic catalytically active antibacterial palladium nanoparticles

Due to being low cost and eco-friendly, biological nanomaterial synthesis and development have made broad spectral progress. This study aimed to optimize the phytomediated synthesis of catalytically active, antibacterial palladium nanoparticles (PdNPs) for adsorption-based removal of ethidium bromide (EtBr) from an aqueous solution. Optimization of synthesis demonstrated that a precursor to extract ratio of 4:1, pH 3, and incubation at 80 °C for 60 min were the optimum conditions that led to the synthesis of negatively charged, highly stable, polycrystalline, spherical, and monodispersed PdNPs of 5-10 nm. When tested as catalysts, PdNPs successfully catalyzed Suzuki-Miyaura cross-coupling between aryl halides and arylboronic acids resulting in the synthesis of 4-acetylbiphenyl. Furthermore, the antibacterial activity test demonstrated that biogenic PdNPs were most effective and potent against Staphylococcus aureus and Proteus vulgaris followed by Escherichia coli, Bacillus subtilis, and Bacillus cereus. In addition, PdNPs were found as an excellent adsorbent for adsorption of EtBr from water as the adsorption reaction obeyed pseudo-second-order kinetics with a linear regression coefficient (R² > 0.995). The adsorption reaction fitted well with the Freundlich and Temkin isotherm models, indicating multi-layer adsorption. Estimating thermodynamic parameters resulted in a positive value of ΔH⁰ and ΔG⁰, demonstrating adsorption was non-spontaneous and endothermic.

Use of Anionic Surfactant-Modified Activated Carbon for Efficient Adsorptive Removal of Crystal Violet Dye

Studies have been carried out to investigate the removal of crystal violet (CV) cationic dye by using rice husk which was used as a raw material to prepare activated carbon (AC) and it was treated with anionic surfactant. In this process, AC was treated with three different anionic surfactants, namely, lauryl sulfate ACMAS, ACSDS, and ACHTAB. Characterization and analysis of optimum ACMAS were done using different techniques which were used which proves the adsorption of the dye by ACMAS. Effects of various physical parameters like time of contact, additive salts, initial dye concentration, effect of pH, and effect of adsorbent dose were studied. Minute changes in the dye removal capacity were observed due to the presence of various cations. Cations like NO2- caused an increase in the capacity of adsorption but cations like Fe2+decreased the capacity of adsorption in the sample solution. The effectiveness of film diffusion and intraparticle has been shown by mass transfer parameters. The various kinetic studies have shown that pseudo second-order kinetic study best suited with the experimental data. Error analysis and studies of isotherms have shown that the adsorption equilibrium was controlled by Langmuir isotherm study with maximum CV dye adsorption capacity of 235.7 mg/g. Thermodynamics studies revealed endothermicity of the process with negative $\Delta G$ values and positive $\Delta S$ and $\Delta H$ values. Activation energy of 48.31 kJ/mol suggested chemisorption process of the system. Column studies were carried out by using different models to study the variation of bed depth, dye concentration, flow rate, etc. Regeneration experiments have given the ability of the adsorbent to be reused. In this present study, it has been noticed that the use of anionic surfactant-treated activated carbon significantly improved the adsorption of dye and this is a process of adsorption in which not much attention has been given for research till date.

Do Red Seaweed Nanoparticles Enhance Bioremediation Capacity of Toxic Dyes from Aqueous Solution?

Based on their functional groups, the use of various seaweed forms in phytoremediation has recently gained significant eco-friendly importance. The objective of this study was to determine whether a novel, sustainable, and ecologically acceptable adsorbent could be employed to remove toxic textile dye (Ismate Violet 2R (IV2R)) from an aqueous solution. The low-cost adsorbent was prepared from the nanoparticles form of the native red seaweed species, Pterocladia capillacea. Before and after the adsorption procedure, comprehensive characterization experiments on the bio-adsorbent were carried out, including BET, SEM, FTIR, UV, and dynamic light scattering (DLS) examination. The adsorption performance of the prepared nano-Pterocladia capillacea was optimized by adjusting operating parameters such as the initial dye concentration of 60 mg L⁻¹, pH of 2, and contact time of 15 min, all of which were obtained by batch experiments in the lab. At the optimum conditions, the prepared adsorbent had maximum removal effectiveness of 87.2%. Most typical kinetics and isotherm models were used to test the experimental results. The equilibrium data fit well with the Langmuir isotherm model, with comparatively higher R² values and fewer standard errors, while the pseudo-second-order kinetic model fits better with a decent correlation coefficient. Thermodynamic parameters revealed that the sorption process on nano-alga was exothermic and spontaneous.

Effect of nano bentonite on direct yellow 50 dye removal; Adsorption isotherm, kinetic analysis, and thermodynamic behavior

Developing countries suffering from the toxicity of different industrial effluents especially dyes. This study successfully prepared and characterized nano-bentonite for anionic dye removal (DY 50). The prepared nanoparticles were characterized by X-Ray Diffraction (XRD), X-ray Fluorescence (XRF), Scanning Electron Microscope (SEM), EDAX analysis, FT-IR, and TGA and the obtained results indicated the formation of nanoparticles with an average size of 15 nm. The effect of different operating conditions was studied using different pH, dose, contact time, temperature, and initial DY 50 concentrations. The obtained results indicated that nano bentonite was able to adsorb about 78.3 and 100% for initial concentrations of 100±8.1 and 20 ±1.62 mg/L, respectively. The optimum removal conditions were observed at acidic media (pH 3) using sorbent material dosage 1 g/L for 45 min and 30°C. The adsorption isotherm, kinetic analysis, and thermodynamic behavior were studied by using linear equation form, and the adjusted R2 was compared to detect the preferred models. The adsorption isotherm indicated that heterogeneous, as well as multilayer adsorption, plays an important role in the removal of dye. Kinetic studies indicated the chemisorption interaction between sorbed and adsorbed molecules. Thermodynamic behavior indicated the reaction is exothermic with ∆H equal to −5.24 KJ/mol and ∆S equal −74.2 J/K.mol. Finally, this study strongly recommended using nano bentonite for DY 50 removal from an aqueous solution. The RSM relations show significant relations in all removal models with p-value <0.001. The ANN results indicated that the most effective operating conditions are the effect of nano bentonite dose followed by the pH effect.

Sequestration of crystal violet dye from wastewater using low-cost coconut husk as a potential adsorbent

The current study explores the effectiveness of coconut husk for crystal violet dye sequestration employing a batch experimental setup. Characterization of adsorbent was carried out via FTIR, and SEM techniques and results confirmed the involvement of -OMe, -COC- and hydroxyl functional groups in dye uptake, and the rough, porous nature of adsorbent and after adsorption dye molecules colonized these holes resulting in dye exclusion. Effects of various adsorption parameters such as pH, adsorbent dose, contact time, initial dye concentration, and temperature of solution were studied. Crystal violet adsorption on coconut husk was highly pH-dependent, with maximum removal occurring at basic pH. Maximum removal of dye, i.e., 81%, takes place at optimized conditions. Kinetic data was analyzed by pseudo-first, pseudo-second order and an intra-particle diffusion model. Results showed that the pseudo-second order kinetic model best described adsorption of crystal violet onto coconut husk. Langmuir, Freundlich, and D-R adsorption isotherms were also used to test their appropriateness to experimental data and the Freundlich isotherm fits best to data. Thermodynamic parameters showed that the current process was spontaneous, endothermic in nature with continuous decrease in entropy. Established practice is 79% applicable to tap water and in acidic medium nearly 80% of adsorbent was recovered, confirming the effectiveness and appropriateness of coconut husk for crystal violet dye exclusion from wastewater.

Sodium salt-assisted low temperature activation of bentonite for the adsorptive removal of methylene blue

The sodium salt-assisted low temperature activation of bentonite (BB) was attempted. The unique features of the raw bentonite and BB were characterized with respect to the morphological, functional, and textural analysis. The adsorptive behaviour was evaluated by adopting methylene blue (MB) as the model pollutant via batch adsorption experiment. The experimental data were fitted to the non-linear isotherm equations (Freundlich, Langmuir, and Temkin), while the adsorption modelling was interpreted by the pseudo-first order, pseudo-second order and Elovich models. The adsorptive mechanism was ascertained according to intraparticle-diffusion and boyd models. The intercalation of sodium salt into the bentonite surface give rise to the specific surface area and total pore volume from 120.34 to 426.91, m²/g and 0.155 to 0.225 cm³/g, respectively, indicating a large proportion of the newly formed surfaces may be connected to new pore walls, associated with the silanol (≡SiOH), and aluminol (≡AlOH), and hydroxyl (–OH) groups for the possible entrapment MB onto the adsorbent. The equilibrium data was satisfactory described by the Langmuir isotherm and pseudo-second order model, with a monolayer adsorption capacity for MB of 318.38 mg/g, while the thermodynamic study verified spontaneous, feasible, and endothermic of the adsorption process.

Adsorption of Cationic and Anionic Dyes from Aqueous Solution Using Sunflower Husk

The current study deals with the removal of cationic dye (brilliant green) and anionic dye (methyl orange) from wastewater by using sunflower husk as an adsorbent. The operation takes place batch wise by applying several concentrations of the dye solution with various adsorbent amounts, at a range of initial PH values and particle sizes at varying contact time intervals. The percent of dye removed for two dyes increased with increasing time and adsorbent dose and decreased with increasing the dye concentration and particle size. The equilibrium time differed according to conditions used. The optimum removal for brilliant green dye was 98 %, which was achieved at 50 ppm dye concentration, 2 g\l adsorbent dose, 75 µm particles size and pH 7 at contact time of 1 h, compared with low removal for methyl orange that reached 54 % under optimum conditions (dye concentration 10 ppm, adsorbent dose 4 g/l, pH 3 at the same particles size and time). Kinetic studies were conducted and revealed that the adsorption was well defined by pseudo-second order model and could be described by the Langmuir isotherm.

Castor Leaves-Based Biochar for Adsorption of Safranin from Textile Wastewater

The prospect of synthesizing biochar from agricultural wastes or by-products to utilize them as a promising adsorbent material is increasingly gaining attention. This research work focuses on synthesizing biochar from castor biomass (CBM) and evaluating its potential as an adsorbent material. Castor biomass-based biochar (CBCs) prepared by the slow pyrolysis process at different temperatures (CBC400 °C, CBC500 °C, and CBC600 °C for 1 h) was investigated for the adsorption of textile dye effluents (safranin). The pyrolysis temperature played a key role in enhancing the morphology, and the crystallinity of the biochar which are beneficial for the uptake of safranin. The CBC600 adsorbent showed a higher safranin dye removal (99.60%) and adsorption capacity (4.98 mg/g) than CBC500 (90.50% and 4.52 mg/g), CBC400 (83.90% and 4.20 mg/g), and castor biomass (CBM) (64.40% and 3.22 mg/g). Adsorption data fitted better to the Langmuir isotherm model than to the Freundlich isotherm model. The kinetics of the adsorption process was described well using the pseudo-second-order kinetic model. The study on the effect of the contact time for the adsorption process indicated that for CBC600, 80% dye removal occurred in the first 15 min of the contact time. After three regeneration cycles, CBC600 exhibited the highest dye removal efficiency (64.10%), highlighting the enhanced reusability of CBCs. The crystalline patterns, functional binding sites, and surface areas of the prepared CBCs (CBC400, CBC500, CBC600) were characterized by X-ray diffraction, Fourier transform infrared spectroscopy, and Brunauer–Emmett–Teller surface area measurements, respectively.

Magnetic nanocomposites for sustainable water purification-a comprehensive review

Numerous contaminants in huge amounts are discharged to the environment from various anthropogenic activities. Waterbodies are one of the major receivers of these contaminants. The contaminated water can pose serious threats to humans and animals, by distrubing the ecosystem. In treating the contaminated water, adsorption processes have attained significant maturity due to lower cost, easy operation and environmental friendliness. The adsorption process uses various adsorbent materials and some of emerging adsorbent materials include carbon- and polymer-based magnetic nanocomposites. These hybrid magnetic nanocomposites have attained extensive applications in water treatment technologies due to their magnetic properties as well as combination of unique characteristics of organic and inorganic elements. Carbon- and polymer-related magnetic nanocomposites are more adapted materials for the removal of various kinds of contaminants from waterbodies. These nanocomposites can be produced via different approaches such as filling, pulse-laser irradiation, ball milling, and electro-spinning. This comprehensive review is compiled by reviewing published work of last the latest recent 3 years. The review article extensively focuses on different approaches for producing various carbon- and polymer-based magnetic nanocomposites, their merits and demerits and applications for sustainable water purification. More specifically, use of carbon- and polymer-based magnetic nanocomposites for removal of heavy metal ions and dyes is discussed in detail, critically analyzed and compared with other technologies. In addition, commercial viability in terms of regeneration of adsorbents is also reviewed. Furthermore, the future challenges and prospects in employing magnetic nanocomposites for contaminant removal from various water sources are presented.

Adsorptive removal of direct red 80 and methylene blue from aqueous solution by potato peels: a comparison of anionic and cationic dyes

Adsorption of direct red 80 (DR 80) and methylene blue (MB) from aqueous solutions on potato peels (PP) has been compared. The use of peels in decontamination technology is very promising given the near zero-cost for the synthesis of those adsorbents. The selected potato peels were first analyzed by scanning using electron microscopy (SEM) and Fourier transforms infrared spectroscopy (FTIR). Then the adsorption behavior was studied in a batch system. The adsorption process is affected by various parameters such as the solution pH (2-11), the initial concentration of the dye (20, 50, 100, 150 and 200 mg L^-1), the adsorbent dose (0.1-3%), the temperature (303.16 K, 313.16 K, and 323.16 K), agitation (up to 250 rpm), as well as the contact time. Adsorption isotherms of the studied dye on the adsorbent were determined and compared with the Langmiur, Freundlich and Temkin adsorption models. The results show that the data was most similar to the Freundlich isotherm (R² = 0.99). The maximum adsorption capacities (Q_max) of MB and DR 80 by the PP at temperatures 303.16 K, 313.16 K and 323.16 K were found to be approximately 97.08 mg g^-1; 45.87 mg g^-1; 61.35 mg g^-1 and 27.778 mg g^-1; 45.45 mg g^-1; and 32.258 mg g^-1. The kinetic data was compared to the pseudo-first-order, pseudo-second-order, and intraparticle diffusion models. This revealed that adsorption of methylene blue onto PP abided mostly to the pseudo-second-order kinetic model. Calculations of various thermodynamic parameters such as enthalpy change (ΔH), entropy change (ΔS), and free energy change (ΔG) display the endothermic and spontaneous nature of the adsorption process.

Development of a Process for Color Improvement of Low-Grade Dark Maple Syrup by Adsorption on Activated Carbon

Low-grade dark maple syrup was successfully discolored on activated carbon. Several experimental parameters were tested, namely, the mixing time (20, 40, and 60 min), concentration of the activated carbon (0.1, 0.3, and 0.5 g/100 mL), type of activated carbon (I, II, and III), activated carbon particle size (25, 50, and 75 μm), stirring speed (200, 400, and 600 rpm), and temperature (40, 60, and 80 °C). The obtained results showed that the discoloration is optimal by applying the following parameters: a mixing time of 40 min with a type III activated carbon at a concentration of 0.3 g/100 mL. These parameters yielded a light transmittance at 560 nm of 83.70 ± 0.21%, which ranks the syrup in the extra clear class according to the Canadian classification. The results showed that among the tested carbons, the adsorption on the type III carbon followed the Langmuir, Freundlich, and Langmuir-Freundlich adsorption isotherms. Regarding the effect of the particle size, the obtained results showed that a mean size of 25 μm combined with a stirring speed of 200 rpm and working temperature of 80 °C was the most effective one. The optimized conditions showed a good adequacy with the Langmuir and Freundlich models. The discoloration process by using the type III activated carbon followed the pseudo-second-order kinetics.

Experimental modeling, optimization and comparison of coagulants for removal of metallic pollutants from wastewater

Wastewater treatment coagulation is one of the most important physicochemical operations used in industry. The adsorption capability of marigold leaf powder, tea waste and ferrous sulfate was investigated for domestic and tannery effluents. These adsorbents significantly affected the pH, electrical conductivity (EC) and turbidity of wastewater. Maximum decrease in all the attributes was observed for 10 g of adsorbents application. All the adsorbents significantly affected the physiochemical attributes of both wastewaters. Similarly, maximum adsorption potential was observed in case of tea waste powder. Maximum decrease in all physiochemical attributes such as pH (15%), EC (21%), turbidity (54%), total dissolved solids (TDS; 36%), total suspended solids (TSS; 43%), total hardness (TH; 52%), chloride contents (59%) and phosphate contents (60%) was observed with the application of 10 g of tea waste. Regarding the heavy metals, maximum decrease for cadmium (Cd; 47%), lead (Pb; 81%), arsenic (As; 44%), copper (Cu; 75%), iron (Fe; 49%), chromium (Cr; 68%) and zinc (Zn; 64%) was observed in same treatment. The decreasing order in terms of their adsorption potential for coagulants was tea waste > marigold leaf powder > ferrous sulfate. However, for the wastewater, the maximum effect of adsorbents was observed in case of domestic wastewater as compared to the tannery water. Based on these data, it is suggested that tea waste has maximum adsorption potential for the remediation of wastewater.

The Effect of Temperature on the Biosorption of Dyes from Aqueous Solutions

This work is a review of scientific papers on the influence of temperature (T) on the biosorption of various dyes from aqueous solutions and wastewaters. The dyeing process of textiles is usually carried out at high temperatures, and therefore, the wastewater generated there when entering the treatment plant may still be hot. Hence, depending on the climatic conditions of a given region, the biosorption method used for their purification may occur at various temperatures. Most of the papers clearly stated the positive influence of T on biosorption, generally indicating the chemical nature of this process. At the same time, substantial number of authors confirmed the positive effect of T on the biosorption with an initial T-rise from approximately 20 °C to about 30–40 °C range; conversely, at higher temperatures, they indicated a decrease in the biosorption efficiency. Additionally, many authors clearly implied the negative impact of T on the biosorption parameters. They generally envisaged the physical nature of this process, but also indicated its limitation, as there was only a 15%–50% reduction in biosorption efficiency with an increase in T. In addition, an attempt was made to analyse the effect of temperature on the biosorption process, depending on the type of dye. It could then be cautiously suggested that a moderate increase in the T parameter favourably affected the biosorption of the red and reactive dyes.

Evaluation of Methylene Blue Sorption onto Low-Cost Biosorbents: Equilibrium, Kinetics, and Thermodynamics

This paper presents a study on batch sorption of methylene blue dye from aqueous solution onto Ginkgo biloba sorbent, a waste material produced during the Fall season in many parts of the world. Batch kinetics, equilibrium, and thermodynamic studies were conducted to evaluate the effect of contact time (0–150 min), sorbent dose (0.5–3.0 g/L), pH (2–11), temperature (30–50°C), initial MB concentration (10–30 mg/L), and particle size (177 μm—590 μm) on the methylene blue dye sorption. More than 99% removal of methylene blue was observed within 120 minutes. A Lagergren pseudo-first-order model, a pseudo-second-order model, and intraparticle diffusion models fitted well to the kinetics experimental data. Langmuir and Freundlich isotherm models also fitted well with the observed equilibrium data. Additionally, removal of methylene blue increased with increase in solution pH. Higher sorption capacity (∼20 mg/g) was observed with smaller particle size (170 μm) as compared to larger particle sizes (590 μm). Thermodynamic parameters such as ∆G°, ∆H°, and ∆S° indicated that the sorption process was feasible, spontaneous, and endothermic in nature. The study shows that Ginkgo biloba leaves have the potential to be an efficient sorbent for the removal of methylene blue from surface water samples.

Indigo Carmine and 2,6-Dichlorophenolindophenol Removal Using Cetyltrimethylammonium Bromide-Modified Palm Oil Fiber: Adsorption Isotherms and Mass Transfer Kinetics

In the present work, the usefulness of cetyltrimethylammonium bromide-modified palm oil fiber (CTAB-modified POF) for the removal of indigo carmine (IC) and 2,6-dichlorophenolindophenol (2,6-DCPIP) from aqueous solutions was investigated. Raw, NaOH-treated, and CTAB-modified POF were characterized by Fourier-transform infrared (FT-IR) spectroscopy, elemental analysis, thermogravimetric-hyperdifferential scanning calorimetric (TG-HDSC) analysis, X-ray diffraction (XRD), and scanning electron microscopy (SEM). The adsorption studies of IC and 2,6-DCPIP were performed in batch mode using CTAB-modified POF. The results showed that equilibrium was attained after a contact time of 30 minutes for IC and 20 minutes for 2,6-DCPIP. The maximum capacity of adsorption was obtained at pH = 2. The capacity of adsorption considerably increased with modified biosorbents and with increasing initial concentration of dyes. The ionic strength favors the increasing adsorption capacity of IC and does not affect the adsorption capacity of 2,6-DCPIP. The percentage of adsorption increased with increasing mass of the biosorbents. The nonlinear regression of adsorption isotherms showed that Freundlich (r² = 0.953; χ² = 4.398) and Temkin (r² = 0.986; χ² = 1.196) isotherms are most appropriate to describe the adsorption of IC and 2,6-DCPIP on CTAB-modified POF, respectively. The maximum adsorption capacities determined by the Langmuir isotherm were 275.426 and 230.423 μmol·g⁻¹ for IC and 2,6-DCPIP, respectively. The linear regression of adsorption kinetics was best described by the pseudo-second-order model (R² ≥ 0.998). The diffusion mechanism showed that external mass transfer is the main rate controlling step. Desorption of the two dyes is favorable in the alkaline medium.

Preparation and characterization of novel green synthesized iron-aluminum nanocomposite and studying its efficiency in fluoride removal

A novel green synthesized iron-aluminum nanocomposite was prepared and characterized by FESEM, FTIR, EDX, XRD, BET, DSC and TGA analysis. The clove extract acting as both reducing and surface coating agent was optimized based on its maximum total flavonoid content (TFC) and total polyphenolic content (TPC). Fluoride adsorption studies was performed at 298K, 303K and 313K within the range of 10-40 mg/L fluoride solution for kinetic and isotherm studies. Maximum adsorption capacity of 42.95 mg/g was obtained for 0.25 g/L adsorbent dosage. Moreover fluoride adsorption obeyed pseudo second order kinetic model whereas the process was multistage diffusion controlled. Langmuir isotherm model best fitted the equilibrium data with monolayer adsorption capacities of 25.09, 26.08 and 28.07 mg/g at 298, 303 and 313K respectively. The findings confirmed that the fluoride adsorption process followed ion exchange mechanism with the surface hydroxyl groups. The prepared nanocomposite was utilized for treating fluoride contaminated water samples from north-east regions of India which showed efficient removal percentage.

Removal of vanadium from wastewater using surface-modified lignocellulosic material

Palm fruit husk, a lignocellulosic material, is an agricultural solid waste. Since raw palm fruit husk does not adsorb V (V), it was subjected to surface modification with a cationic surfactant cetyl trimethyl ammonium bromide (CTAB). The surface-modified palm fruit husk showed adsorption capability for V (V). The maximum adsorption of V (V) takes place at pH 4. Adsorption equilibrium data were fitted to Langmuir, Freundlich, and Dubinin Radushkevich (D-R) isotherm models. Kinetic studies showed that the adsorption data fit second-order kinetic model better than first order. Desorption of V (V) proved that it is feasible to recover V (V) from the spent adsorbent. Effect of coexisting anions like Molybdate, sulfate, nitrate, phosphate, and thiocyanate on the adsorption of V (V) was also studied and the foreign ions compete for the adsorption sites with V (V) anionic species. Quantitative removal of V (V) was achieved from synthetic wastewater.

Biosorption of Basic Blue 7 by fungal cells immobilized on the green-type biomatrix of Phragmites australis spongy tissue

Biosorption is an effective alternative method for the control of water pollution caused by different pollutants such as synthetic dyes and metals. A new and efficient biomass system was developed from the passively immobilized fungal cells. The spongy tissue of Phragmites australis was considered as the carrier for the immobilization of Neurospora sitophila cells employed for the biosorption of Basic Blue 7. This plant tissue was used for the first time as a carrier for fungal cells. The biosorption was examined through batch- and continuous-mode operations. The biosorption process conformed well to the Langmuir model. Maximum monolayer biosorption capacity of the biosorbent was recorded as 154.756 mg g^-1. Kinetic findings showed a very good compliance with the pseudo-second-order model. The negative values of ΔG° indicated a spontaneous nature of the biosorption process and a positive value of ΔH° (14.69 kJ mol^-1) concluded favorable decolorization at high temperature. The scanning electron microscopy analysis showed that a porous, rippled, and rough surface of biomass system was covered with BB7 molecular cloud. IR results revealed that functional groups like -OH, -NH, and C˭O participated to the decolorization. Breakthrough and exhausted points were found as 360 and 570 minutes, respectively. The biomass system was successfully applied to the treatment of real wastewater.

Titanium Pyrophosphate for Removal of Trivalent Heavy Metals and Actinides Simulated by Retention of Europium

This work addresses the synthesis of titanium pyrophosphate, as well as the characterization and evaluation of the sorption process of europium, for removal of trivalent heavy metals and actinides simulate. The evaluation of the surface properties of titanium pyrophosphate was carried out determining the surface roughness and surface acidity constants. The values obtained from the determination of the surface roughness of the synthesized solid indicate that the surface of the material presents itself as slightly smooth. The FITEQL program was used to fit the experimental titration curves to obtain the surface acidity constants: log⁡K⁺ = 3.59 ± 0.06 and log⁡K^- = -3.90 ± 0.05. The results of sorption kinetics evidenced that the pseudo-order model explains the retention process of europium, in which the initial sorption velocity was 8.3 × 10^-4 mg g^-1 min^-1 and kinetic constant was 1.8 × 10^-3g mg min^-1. The maximum sorption capacity was 0.6 mg g^-1. The results obtained from sorption edge showed the existence of two bidentate complexes on the surface.

A comprehensive study on adsorption behavior of some azo dyes from aqueous solution onto different adsorbents

One of the major environmental problems is the existence of dye materials in water sources. This pollutant must be removed from water by appropriate methods. Although most of these methods are efficient for the treatment of waters contaminated with dye pollutants, they are very costly and commercially unattractive. Adsorption is one of the most popular methods for the removal of dye pollutants from water especially if the sorbent is inexpensive. Sorbents are classified as natural sorbents, commercial sorbents, and the sorbents obtained from industrial and agricultural wastes. Although commercial activated carbon is widely used in wastewater treatment applications, it is very expensive. In this study, usability of inexpensive materials - sepiolite as a natural adsorbent, and walnut shell and hazelnut shell as agricultural wastes - was investigated instead of commercial activated carbon to remove some azo dyes (methyl red, methyl orange and methyl yellow) from aqueous solution. Batch experiments were carried out to determine the effect of different adsorption parameters such as pH, initial dye concentration, contact time, adsorbent dose and temperature. The equilibrium of adsorptions was modeled using Langmuir and Freundlich isotherm models. This comprehensive study showed that these alternative adsorbents had sufficient binding capacity to remove these azo dyes from water.

Selective adsorption of Pb (II) over the zinc-based MOFs in aqueous solution-kinetics, isotherms, and the ion exchange mechanism

Two series of metal-organic frameworks (MOFs) with similar formula units but different central metal ions (M) or organic linkers (L), M-BDC (BDC = terephthalate, M = Zn, Zr, Cr, or Fe), or Zn-L (L = imidazolate-2-methyl, BDC, BDC-NH₂), were prepared and employed as the receptors for adsorption lead ions. It was found that the Zn-BDC exhibited a much higher adsorption capacity than the other M-BDC series with various metal ions which have very closely low capacities at same conditions. Furthermore, the Zn-L (L = imidazolate-2-methyl, BDC, BDC-NH₂) still have highly efficient adsorption capacity of lead ions, although the adsorption capacity varies with different ligand, as well as the adsorption rate and the equilibrium pH of the solution. This significant high adsorption over Zn-L, different from other M-BDC series with various metal ions (Zr, Cr, or Fe), can be explained by ion exchange between the central metal ions of Zn-L and lead ion in solution. Based on the analysis of FT-IR, X-ray diffraction pattern, the nitrogen adsorption isotherms, the zeta potentials, and the results, a plausible adsorption mechanism is proposed. When equivalent Zn-L were added to equal volume of aqueous solution with different concentration of lead ion, the content of zinc ion in the solution increases with the increase of the initial concentration of lead ions. The new findings could provide a potential way to fabricate new metal organic frameworks with high and selective capacities of the heavy metal ions.

Behavior of mesoporous activated carbon used as a remover in Congo red adsorption process

The adsorption characteristics of Congo red (CR) dye on activated carbon produced under optimized conditions from tomato paste waste were evaluated. The effects of adsorbent dose, initial dye concentration, contact time, ionic strength and solution temperature on adsorption were investigated. Adsorption kinetic was better described by the pseudo-first order model. Results of the intra-particle diffusion model show that the pore diffusion is not the only rate-limiting step. Adsorption isotherm was well defined by the Langmuir isotherm. The maximum adsorption capacity of the activated carbon was 435 mg g^-1 at 328 K. The dimensionless separation factor R_L revealed the favorable nature of the isotherm of the activated carbon-dye system. Adsorption energy was found to be 4.20-4.55 kJ mol^-1 indicating that the mechanism of adsorption is physical in nature. Thermodynamic studies showed that CR adsorption onto activated carbon was feasible, spontaneous and endothermic. Desorption of the used activated carbon was studied using ethanol as solvent and desorption efficiency of 56.4% was obtained after five cycles. The findings indicated that the activated carbon is a very effective and low-cost adsorbent for removal of CR dye from aqueous solutions.

Photocatalytic decomposition of Congo red under visible light irradiation using MgZnCr-TiO2 layered double hydroxide

The new nanophotocatalyst MgZnCr-TiO₂ was prepared by co-precipitation under different molar ratio of metals (Zn:Cr) and the loaded amount of TiO₂. And it was characterized by X-ray diffraction, Raman spectroscopy, X-ray photoelectron spectroscopy et al. Langmuir model fitted well the adsorption isotherm with the value of R² 0.9765, the maximum adsorption capacity was 526.32 mg g^-1, the adsorption followed pseudo second order kinetic by MgZnCr-TiO₂ (1:1:2-0.05). The photocatalytic oxidation of Congo red was used to determine the photocatalytic performance of MgZnCr-TiO₂ (1:1:2-0.05) under visible light irradiation, and the removal rate reached 98% after reaction for 40 min. The degradation mechanism of Congo red also was proposed, and the MgZnCr-TiO₂ (1:1:2-0.05) was stable after five cycles. Compared to the adsorption, Congo red was removed fundamentally by photocatalysis and it is expected to be an effective way to eliminate Congo red.

Investigation of adsorption of Rhodamine B onto a natural adsorbent Argemone mexicana

The present study aims at exploring the potential of the seeds of a tropical weed, Argemone mexicana (AM), for the removal of a toxic xanthene textile dye, Rhodamine B (RHB), from waste water. Impact of pH, adsorbent dosage, particle size, contact time and dye concentration have been assessed during adsorption. The weed has been well characterized by several latest techniques thereby providing an indepth information of the mechanism during adsorption. About 80% removal has been attained with 0.06 g of adsorbent over the studied system. Thermodynamic and kinetic studies, followed by second order kinetic model, directed towards the endothermic nature of adsorption. The results obtained from batch experiments were modelled using Langmuir and Freundlich isotherm and were analysed on the basis of R² and six error functions for selection of appropriate model. Langmuir isotherm was found to be best fitted to the experimental data with high values of R² and lower values of error functions. Adsorption study revealed the affinity of AM seeds for the dye ions present in waste water, introducing a novel adsorbent in field of waste water treatment.