Treatment of olive mill effluent by adsorption on titanium oxide nanoparticles

Integrating of electrocoagulation process with submerged membrane bioreactor for wastewater treatment under low voltage gradients

Treating and reusing wastewater has become an essential aspect of water management worldwide. However, the increase in emerging pollutants such as polycyclic aromatic hydrocarbons (PAHs), which are presented in wastewater from various sources like industry, roads, and household waste, makes their removal difficult due to their low concentration, stability, and ability to combine with other organic substances. Therefore, treating a low load of wastewater is an attractive option. The study aimed to address membrane fouling in the submerged membrane bioreactor (SMBR) used for wastewater treatment. An aluminum electrocoagulation (EC) device was combined with SMBR as a pre-treatment to reduce fouling. The EC-SMBR process was compared with a conventional SMBR without EC, fed with real grey water. To prevent impeding biological growth, low voltage gradients were utilized in the EC deviceThe comparison was conducted over 60 days with constant transmembrane pressure and infinite solid retention time (SRT). In phase I, when the EC device was operated at a low voltage gradient (0.64 V/cm), no significant improvement in the pollutants removal was observed in terms of color, turbidity, and chemical oxygen demand (COD). Nevertheless, during phase II, a voltage gradient of 1.26 V/cm achieved up to 100%, 99.7%, 92%, 94.1%, and 96.5% removals in the EC-SMBR process in comparison with 95.1%, 95.4%, 85%, 91.7% and 74.2% removals in the SMBR process for turbidity, color, COD, ammonia nitrogen (NH3-N), total phosphorus (TP), respectively. SMBR showed better anionic surfactant (AS) removal than EC-SMBR. A voltage gradient of 0.64 V/cm in the EC unit significantly reduced fouling by 23.7%, while 1.26 V/cm showed inconsistent results. Accumulation of Al ions negatively affected membrane performance. Low voltage gradients in EC can control SMBR fouling if Al concentration is controlled. Future research should investigate EC-SMBR with constant membrane flux for large-scale applications, considering energy consumption and operating costs.

MXenes and MXene-based materials for removal of pharmaceutical compounds from wastewater: Critical review

The rapid increase in the global population and its ever-rising standards of living are imposing a huge burden on global resources. Apart from the rising energy needs, the demand for freshwater is correspondingly increasing. A population of around 3.8 billion people will face water scarcity by 2030, as per the reports of the World Water Council. This may be due to global climate change and the deficiency in the treatment of wastewater. Conventional wastewater treatment technologies fail to completely remove several emerging contaminants, especially those containing pharmaceutical compounds. Hence, leading to an increase in the concentration of harmful chemicals in the human food chain and the proliferation of several diseases. MXenes are transition metal carbide/nitride ceramics that primarily structure the leading 2D material group. MXenes act as novel nanomaterials for wastewater treatment due to their high surface area, excellent adsorption properties, and unique physicochemical properties, such as high electrical conductivity and hydrophilicity. MXenes are highly hydrophilic and covered with active functional groups (i.e., hydroxyl, oxygen, fluorine, etc.), which makes them efficient adsorbents for a wide range of species and promising candidates for environmental remediation and water treatment. This work concludes that the scaling up process of MXene-based materials for water treatment is currently of high cost. The up-to-date applications are still limited because MXenes are currently produced mainly in the laboratory with limited yield. It is recommended to direct research efforts towards lower synthesis cost procedures coupled with the use of more environmentally friendly materials to avoid secondary contamination.

Microplastics in sewage sludge: Distribution, toxicity, identification methods, and engineered technologies

Microplastic pollution is becoming a global challenge due to its long-term accumulation in the environment, causing adverse effects on human health and the ecosystem. Sludge discharged from wastewater treatment plants (WWTPs) plays a critical role as a carrier and primary source of environmental microplastic contamination. A significantly average microplastic variation between 1000 and 301,400 particles kg^-1 has been reported in the sludge samples. In recent years, advanced technologies have been successfully applied to address this issue, including adsorption, advanced oxidation processes (AOPs), and membrane bioreactors (MBRs). Adsorption technologies are essential to utilizing novel adsorbents (e.g., biochar, graphene, zeolites) for effectively removing MPs. Especially, the removal efficiency of polymer microspheres from an aqueous solution by Mg/Zn modified magnetic biochars (Mg/Zn-MBC) was obtained at more than 95%. Also, advanced oxidation processes (AOPs) are widely applied to degrade microplastic contaminants, in which photocatalytic by semiconductors (e.g., TiO₂ and ZnO) is a highly suitable approach to promote the degradation reactions owing to strongly hydroxyl radicals (OH*). Biological degradation-aided microorganisms (e.g., bacterial and fungal strains) have been reported to be suitable for removing microplastics. Yet, it was affected by biotic and abiotic factors of the environmental conditions (e.g., pH, light, temperature, moisture, bio-surfactants, microorganisms, enzymes) as well as their polymer characteristics, i.e., molecular weight, functional groups, and crystallinity. Notably, membrane bioreactors (MBRs) showed the highest efficiency in removing up to 99% microplastic particles and minimizing their contamination in sewage sludge. Further, MBRs illustrate the suitability for treating high-strength compounds, e.g., polymer debris and microplastic fibers from complex industrial wastewater. Finally, this study provided a comprehensive understanding of potential adverse risks, transportation pathways, and removal mechanisms of microplastic, which full-filled the knowledge gaps in this field.

A comprehensive review of nanoparticles: Effect on water-based drilling fluids and wellbore stability

Wellbore stability in shale is a recurring crisis during oil and gas well drilling. The adsorption of water and ions from drilling fluid by shale, which causes clay swelling, is the primary cause of wellbore instability. Nanomaterials have been a subject of interest in recent years to be an effective shale inhibitor in drilling fluid, intending to minimize clay swelling. This article presents a comprehensive review of the current progress of nanoparticle role in water-based drilling fluid with regards to wellbore stability, reviewing the experimental methods, the effect of nanoparticles in drilling fluid, the mechanism of shale stability and the outlook for future research. This paper employed a systematic review methodology to highlight the progress of nanoparticle water-based drilling fluids in recent years. Previous studies indicated the current trend for drilling fluid additives was nanoparticles modified with surfactants and polymers, which minimize colloidal stability issues and enhance shale stability. A review of experimental methods showed that the pressure transmission test benefits shale stability assessment under reservoir conditions. Parametric analysis of nanoparticles showed that parameters such as concentration and size directly affected the shale stability even in high salinity solution. However, there is a lack of studies on nanoparticle types, with silica nanoparticles being the most popular among researchers. Nanoparticles enhance shale stability via physical plugging, chemical inhibition, and electrostatic interactions between surface charges. To better comprehend the influence of nanoparticles on shale stabilization, it is necessary to evaluate a wider range of nanoparticle types using the proper experimental techniques.

Sustainable vs. Conventional Approach for Olive Oil Wastewater Management: A Review of the State of the Art

The main goal of this review is to collect and analyze the recently published research concerning the conventional and sustainable treatment processes for olive mill wastewater (OMW). In the conventional treatment processes, it is noticed that the main objective is to meet the environmental regulations for remediated wastewater without considering the economical values of its valuable constituents such as polyphenols. These substances have many important environmental values and could be used in many vital applications. Conversely, sustainable treatment processes aim to recover the valuable constituents through different processes and then treat the residual wastewater. Both approaches’ operational and design parameters were analyzed to generalize their advantages and possible applications. A valorization-treatment approach for OMW is expected to make it a sustainable resource for ingredients of high economical value that could lead to a profitable business. In addition, inclusion of a recovery process will detoxify the residual OMW, simplify its management treatment, and allow the possible reuse of the vast amounts of processed water. In a nutshell, the proposed approach led to zero waste with a closed water cycle development.

In Vitro Hepatotoxic and Neurotoxic Effects of Titanium and Cerium Dioxide Nanoparticles, Arsenic and Mercury Co-Exposure

Considering the increasing emergence of new contaminants, such as nanomaterials, mixing with legacy contaminants, including metal(loid)s, it becomes imperative to understand the toxic profile resulting from these interactions. This work aimed at assessing and comparing the individual and combined hepatotoxic and neurotoxic potential of titanium dioxide nanoparticles (TiO₂NPs 0.75–75 mg/L), cerium oxide nanoparticles (CeO₂NPs 0.075–10 μg/L), arsenic (As 0.01–2.5 mg/L), and mercury (Hg 0.5–100 mg/L) on human hepatoma (HepG2) and neuroblastoma (SH-SY5Y) cells. Viability was assessed through WST-1 (24 h) and clonogenic (7 days) assays and it was affected in a dose-, time- and cell-dependent manner. Higher concentrations caused greater toxicity, while prolonged exposure caused inhibition of cell proliferation, even at low concentrations, for both cell lines. Cell cycle progression, explored by flow cytometry 24 h post-exposure, revealed that TiO₂NPs, As and Hg but not CeO₂NPs, changed the profiles of SH-SY5Y and HepG2 cells in a dose-dependent manner, and that the cell cycle was, overall, more affected by exposure to mixtures. Exposure to binary mixtures revealed either potentiation or antagonistic effects depending on the composition, cell type and time of exposure. These findings prove that joint toxicity of contaminants cannot be disregarded and must be further explored.

Olive Mill Wastewater Valorization through Steam Reforming Using Multifunctional Reactors: Challenges of the Process Intensification

Olive oil mill wastewater (OMW) is a polluting stream derived from the production of olive oil and is a source of environmental pollution; this is relevant in many countries around the world, but particularly in all the Mediterranean region where major producers are located. In this effluent, several pollutants are present—namely, sugars, fatty acids, and polyphenols, among others. Nowadays, to reduce the pollutant load, several treatment techniques are applied, but these technologies have numerous cost and efficiency problems. For this reason, the steam reforming of the OMW (OMWSR) presents as a good alternative, because this process decreases the pollutant load of the OMW and simultaneously valorizes the waste with the production of green H2, which is consistent with the perspective of the circular economy. Currently, the OMWSR is an innovative treatment alternative in the scientific field and with high potential. In the last few years, some groups have studied the OMWSR and used innovative reactor configurations, aiming to improve the process’ effectiveness. In this review, the OMW treatment/valorization processes, the last developments on catalysis for OMWSR (or steam reforming of similar species present in the effluent), as well as the last advances on OMWSR performed in multi-functional reactors are addressed.

Olive mill wastewater phytoremediation employing economically important woody plants

In this study two plant species, Punica granatum L. and Myrtus communis L., have been tested as candidates for phytoremediation of olive mill wastewater (OMW) through recirculation in soil pilot units, according to the proposed patented technology by Santori and Cicalini [EP1216963 A. 26 Jun 2002]. Wastewater was treated in batches of low to high organics strength (COD: 2 700-45 700 mg/L) during summer months of two consecutive years. Dynamics of the most important wastewater parameters were investigated, and corresponding removal rates were estimated. During treatment of low organic load OMW, average removal rate of organics, phenolics, total nitrogen and total phosphorus were 0.68 g-COD/kg-soil d, 0.073 g-TPh/kg-soil d, 0.033 g-TN/kg-soil d and 0.0074 g-TP/kg-soil d respectively and plants proved to be tolerant to the OMW. During treatment of high organic load OMW removal rates were roughly 10-fold higher although phytotoxic symptoms were observed. Plants were found to contribute greatly to the OMW treatment process since organics removal rates in pilot units were found to be at least 10-fold higher than in wastewater treatment in non-vegetated soil. Plant species with high added value products such as pomegranate and myrtle trees were used in this study, improving the circular economy potential of the aforementioned technology. Moreover, its efficiency has been demonstrated by quantification of the overall removal rates of key constituents as well as the contribution of the plants in the OMW treatment.

Preparation of Activated Carbon Derived from Jordanian Olive Cake and Functionalized with Cu/Cu2O/CuO for Adsorption of Phenolic Compounds from Olive Mill Wastewater

Olive oil production generates solid and liquid wastes that cause various environmental problems due to their high phenols and polyphenols load. Although many treatment methods were investigated to manage these wastes, more research is still needed to identify simple and cost-effective approaches. In this study, activated carbon (AC) was prepared from olive cake waste and functionalized with Cu/Cu₂O/CuO for efficient and selective removal of phenolic content from olive mill wastewater (OMW). AC media were characterized by scanning electron/dispersive X-ray spectroscopy (SEM-EDS), X-ray diffraction (XRD), Fourier transform infrared (FTIR) spectrometry, and Brunauer-Emmett-Teller (BET) surface area analysis. The optimum adsorption parameters were investigated, and the adsorption isotherms, thermodynamics, and kinetics were determined. The adsorption of phenols onto copper oxide AC was best described by the Langmuir adsorption with maximum adsorption capacity of 13.9, 12.7, and 9.9 mg/g at 311, 302, and 293 K, respectively. The adsorption reaction was found to be spontaneous and endothermic where ∆H° and ∆G° were found to be 30.104 kJ/mol and -1.765, -2.839, and -3.723 (kJ/mol) at 311, 302, and 293 K, respectively. In addition, the kinetics data were perfectly fit by the pseudo-second-order model. The activated product derived from recyclable olive cake and enriched with inorganic functionality can offer a cost-effective treatment solution for OMW; thus, reducing both the liquid and solid waste generated from the olive mill industry.

Biodegradable polymers and their nano-composites for the removal of endocrine-disrupting chemicals (EDCs) from wastewater: A review

Endocrine-disrupting chemicals (EDCs) target the endocrine system by interfering with the natural hormones in the body leading to adverse effects on human and animal health. These chemicals have been identified as major polluting agents in wastewater effluents. Pharmaceuticals, personal care products, industrial compounds, pesticides, dyes, and heavy metals are examples of substances that could be considered endocrine active chemicals. In humans, these chemicals could cause obesity, cancer, Alzheimer's disease, autism, reproductive abnormalities, and thyroid problems. While in wildlife, dysfunctional gene expression could lead to the feminization of some aquatic organisms, metabolic diseases, cardiovascular risk, and problems in the reproductive system as well as its levels of hatchability and vitellogenin. EDCs could be effectively removed from wastewater using advanced technologies such as reverse osmosis, membrane treatment, ozonation, advanced oxidation, filtration, and biodegradation. However, adsorption has been proposed as a more promising and sustainable method for water treatment than any other reported technique. Increased attention has been paid to biodegradable polymers and their nano-composites as promising adsorbents for the removal of EDCs from wastewater. These polymers could be either natural, synthetic, or a combination of both. This review presents a summary of the most relevant cases where natural and synthetic biodegradable polymers have been used for the successful removal of EDCs from wastewater. It demonstrates the effectiveness of these polymers as favorable adsorbents for novel wastewater treatment technologies. Hitherto, very limited work has been published on the use of both natural and synthetic biodegradable polymers to remove EDCs from wastewater, as most of the studies focused on the utilization of only one type, either natural or synthetic. Therefore, this review could pave the way for future exploration of biodegradable polymers as promising and sustainable adsorbents for the removal of various types of pollutants from wastewater.

Environment and sustainability approach to manage sweet bakery waste product

Globalization and environmental regulations force organizations and producers to adopt sustainability in every aspect of their business. The concept of sustainability in manufacturing is now achieving maturity; however, there is still an opportunity to explore sustainability in perishable food items. The growth of population worldwide increased the amount of waste produced by the food industries. Enterprises worldwide use procedures to overcome the disposing of perishable waste into landfills, which has noticeable impacts on the environment and the business itself. However, these procedures may not be sufficient and lead to disturbance of the ecosystem. Therefore, the purpose of this article is to develop a framework to conduct experiments using Design of Experiment (DOE) to produce fertilizer using expired doughnuts from a well-known sweet bakery company in the United Arab Emirates. Firstly, we will develop a framework, implement waste management on perishable products such as doughnuts, and apply environmental, economic, and social development through recycling and composting it into fertilizers to be used for agriculture needs. Secondly, to study the impact of different parameters such as water, sand, doughnuts in different percentages on plant growth and survival. Results show that wasted doughnuts are suitable for fertilizer and the best plant due to interaction between all three factors: commercial fertilizer percentage, doughnuts percentage, and doughnuts size.

A powerful arsenite-oxidizing biofilm bioreactor derived from a single chemoautotrophic bacterial strain: Bioreactor construction, long-term operations and kinetic analysis

Microbial oxidation of As(III) by biofilm bioreactors followed by adsorption is a promising and environment friendly approach to remediate As(III) contaminated groundwater; however, poor activity, stability and expandability of the bioreactors hampered their industrious applications. To resolve this issue, we constructed a new biofilm bioreactor using a powerful chemoautotrophic As(III)-oxidizing bacterium Rhizobium sp. A219. This strain has strong ability to form biofilms and possesses very high As(III)-oxidizing activities in both planktonic and biofilm forms. Perlites were used as the biofilm carriers. Long-term operations suggest that the bioreactor has very high efficiency, stability and scalability under different geochemical conditions, and it is cheap and easy to construct and operate. During the operations, it is only required to supply air, nothing else. All the common contaminants in groundwater slightly affected the bioreactor As(III)-oxidizing activity. The common contaminants in groundwater can be largely removed through assimilation by the bacterial cells as nutrition. The bioreactor completely oxidize 1.0, 5.0, 10.0, 20.0 and 30.0 mg/L As(III) in 12, 18, 20, 25 and 30 min, respectively. Approximately 18, 18, 12, 12 and 21 min were needed to oxidize 1.1 mg/L As(III) at 20, 25, 30, 35 and 40 °C, respectively. The bioreactor works well under the pH values of 5-8, and the most optimal was 7.0. The data suggest that this bioreactor possesses the highest efficiency and stability, and thus has the great potential for industrial applications among all the described As(III)-oxidizing bioreactors derived from a single bacterium.

Efficient removal of phenol compounds from water environment using Ziziphus leaves adsorbent

Industrial processes generate toxic organic molecules that pollute environment water. Phenol and its derivative are classified among the major pollutant compounds found in water. They are naturally found in some industrial wastewater effluents. The removal of phenol compounds is therefore essential because they are responsible for severe organ damage if they exist above certain limits. In this study, ground Ziziphus leaves were utilized as adsorbents for phenolic compounds from synthetic wastewater samples. Several experiments were performed to study the effect of several conditions on the capacity of the Ziziphus leaves adsorbent, namely: the initial phenol concentration, the adsorbent concentration, temperature, pH value, and the presence of foreign salts (NaCl and KCl). The experimental results indicated that the adsorption process reached equilibrium in about 4 h. A drop in the amount of phenol removal, especially at higher initial concentration, was noticed upon increasing the temperature from 25 to 45 °C. This reflects the exothermic nature of the adsorption process. This was also confirmed by the calculated negative enthalpy of adsorption (-64.8 kJ/mol). A pH of 6 was found to be the optimum value at which the highest phenol removal occurred with around 15 mg/g at 25 °C for an initial concentration of 200 ppm. The presence of foreign salts has negatively affected the phenol adsorption process. The fitting of the experimental data, using different adsorption isotherms, indicated that the Harkins-Jura isotherm model was the best fit, evident by the high square of the correlation coefficient (R²) values greater than 0.96. The kinetic study revealed that the adsorption was represented by a pseudo-second-order reaction. The results of this study offer a basis to use Ziziphus leaves as promising adsorbents for efficient phenol removal from wastewater.

Environmental impacts of solar photovoltaic systems: A critical review of recent progress and future outlook

Photovoltaic (PV) systems are regarded as clean and sustainable sources of energy. Although the operation of PV systems exhibits minimal pollution during their lifetime, the probable environmental impacts of such systems from manufacturing until disposal cannot be ignored. The production of hazardous contaminates, water resources pollution, and emissions of air pollutants during the manufacturing process as well as the impact of PV installations on land use are important environmental factors to consider. The present study aims at developing a comprehensive analysis of all possible environmental challenges as well as presenting novel design proposals to mitigate and solve the aforementioned environmental problems. The emissions of greenhouse gas (GHG) from various PV systems were also explored and compared with fossil fuel energy resources. The results revealed that the negative environmental impacts of PV systems could be substantially mitigated using optimized design, development of novel materials, minimize the use of hazardous materials, recycling whenever possible, and careful site selection. Such mitigation actions will reduce the emissions of GHG to the environment, decrease the accumulation of solid wastes, and preserve valuable water resources. The carbon footprint emission from PV systems was found to be in the range of 14-73 g CO₂-eq/kWh, which is 10 to 53 orders of magnitude lower than emission reported from the burning of oil (742 g CO₂-eq/kWh from oil). It was concluded that the carbon footprint of the PV system could be decreased further by one order of magnitude using novel manufacturing materials. Recycling solar cell materials can also contribute up to a 42% reduction in GHG emissions. The present study offers a valuable management strategy that can be used to improve the sustainability of PV manufacturing processes, improve its economic value, and mitigate its negative impacts on the environment.

Application of Fe3O4 magnetite nanoparticles grafted in silica (SiO2) for oil recovery from oil in water emulsions

In this study, an innovative magnetic demulsifier (MD) was prepared by grafting a silica layer onto the surface of the Fe₃O₄ magnetic nanoparticles (MNPs) using the modified Stober process. The MD was characterized using various analytical techniques (XRD, FTIR, TGA, TEM, VSM, etc.) and employed to recover oil from O/W emulsion, which were then regenerated and recycled several times. The effects of magnetic demulsifier dosage (MD_dose), the concentration of oil (C_oil), pH, the concentration of the surfactant (C_sur), and separation time (t_sep) on the demulsification efficiency (%η_dem), and the percentage of oil recovered (%R_oil) were evaluated. An excellent %η_dem ≥ 90% was achieved C_oil in the range 50-2000 mg/L. Using an MD_dose as low as 10 mg/L attained a %η_dem in the range of 93%-94.3% for O/W mixtures with C_oil < 2000 mg/L, which slightly decreased to ∼90% for higher concentrations. The reported %R_oil (p-value <0.05) was >90 ± 0.1 for tests carried out with pH ≤ 7 and C_sur ≤ 0.1 g/L and declined at higher pH and C_sur to % 86.5 due to the increase in emulsion stability. The developed MD exhibited high recyclability at an effective and stable %R_oil and %η_dem of ∼90% and 86.4% after 9 cycles, respectively. Demulsification process best fits the combined Langmuir-Freundlich (L-F) isotherm with highest adsorption capacity (Q_max) of 186.0 ± 5 mg_oil/g_MD compared to 86.0 ± 5 mg_oil/g_MD for Fe₃O₄, which is 1.1 folds greater than Q_max reported in the literature for other demulsifiers.

Effect of Zr Impregnation on Clay-Based Materials for H2O2-Assisted Photocatalytic Wet Oxidation of Winery Wastewater

UV-activated Zr-doped composites were successfully produced through the impregnation of Zr on the crystal lattice of different clay materials by a one-step route. Fixing the amount of Zr available for dopage (4%), the influence of different supports, submitted to different chemical treatments, on the photocatalytic activity of the resulting Zr-doped pillared clay materials (PILC) was assessed. Both chemical characterization and structural characterization suggest that the immobilization of Zr on montmorillonite and PILC structures occurred through isomorphic substitution between Si and Zr in the tetrahedral sheet of the clay material. This structural change was demonstrated by significant modifications on Si-OH stretching vibrations (1016 cm−1, 1100 cm−1 and 1150 cm−1), and resulted in improved textural properties, with an increase in surface area from 8 m2/g (natural montmorillonite) to 107 m2/g after the pillaring process, and to 118 m2/g after the pillaring and Zr-doping processes ((Zr)Al-Cu-PILC). These materials were tested in the UV-photodegradation of agro-industrial wastewater (AIW), characterized by high concentrations of recalcitrant contaminants. After Zr-dopage on AlCu-PILC heterogeneous catalyst, the total organic carbon (TOC) removals of 8.9% and 10.4% were obtained through adsorption and 77% and 86% by photocatalytic oxidation, at pH 4 and 7, respectively. These results suggest a synergetic effect deriving from the combination of Zr and Cu on the photocatalytic degradation process.

Combined electrocoagulation processes as a novel approach for enhanced pollutants removal: A state-of-the-art review

A novel approach using the integration of electrocoagulation, with one or more treatment processes has been recently practiced to improve the removal of colloidal and non-biodegradable pollutants. Several treatment processes including adsorption, chemical coagulation, magnetic field, reverse osmosis, and membrane filtration have been combined with electrocoagulation treatment step to improve pollutants removal efficiency. These combined systems showed the potential to improve the performance of the treatment process. This paper presents a state-of-the-art review for the recent processes available in the literature that combine treatment electrocoagulation with one of the previously mentioned treatment processes. It is found that the removal efficiency of any combined processes is higher than that of any single treatment process and the combined process has up to 20% higher removal efficiency compared to electrocoagulation alone. However, most reported studies were conducted at bench-scale level with synthetic wastewater instead of real wastewater. The main aspects of these combined systems including process mechanism, kinetic models, cost and the scale up of combined processes were discussed and summarized. Finally, several concluding remarks were drawn in view of the literature investigations and the gaps that suggest more studies and insights for future development were addressed.

Ultrasonic degradation of nitrosodipropylamine (NDPA) and nitrosodibutylamine (NDBA) in water

Nitrosodipropylamine (NDPA) and nitrosodibutylamine (NDBA), two highly toxics and carcinogenic disinfection by-products, cannot be efficiently removed by conventional water treatment processes, while the ultrasound treatment was developed as a promising alternative. In this work, nitrosodipropylamine (NDPA) and nitrosodibutylamine (NDBA) are degraded by ultrasound treatment. Greater than 99% of NDPA and NDBA mixing solution could be decomposed within 60 min at neutral pH under optimal ultrasound power and frequency settings of 100 W and 600 kHz, respectively. Free radical reactions (OH•) played a significant role and the reaction sites were predominately at the bubble interface. The degradation of both NDPA and NDBA exhibited pseudo-first-order degradation kinetics, and the rate constant k_app was influenced by a number of factors including ultrasonic frequency, power, initial concentration, initial pH, various anions and cations frequently present in drinking water, hydroxyl radical scavengers, and water matrices, especially the promoting effect of various anions and cations and water matrices. The results of this study suggest the potential for ultrasound treatment as a method for removing NAms from water.

Optimal conditions for olive mill wastewater treatment using ultrasound and advanced oxidation processes

The treatment of olive mill wastewater (OMW) in Jordan was investigated in this work using ultrasound oxidation (sonolysis) combined with other advanced oxidation processes such as ultraviolet radiation, hydrogen peroxide (H₂O₂) and titanium oxide (TiO₂) catalyst. The efficiency of the combined oxidation process was evaluated based on the changes in the chemical oxygen demand (COD). The results showed that 59% COD removal was achieved within 90 min in the ultrasound /UV/TiO₂ system. A more significant synergistic effect was observed on the COD removal efficiency when a combination of US/UV/TiO₂ (sonophotocatalytic) processes was used at low ultrasound frequency. The results were then compared with the COD values obtained when each of these processes was used individually. The effects of different operating conditions such as, ultrasound power, initial COD concentration, the concentration of TiO₂, frequency of ultrasound, and temperature on the OMW oxidation efficiency were studied and evaluated. The effect of adding a radical scavenger (sodium carbonate) on the OMW oxidation efficiency was investigated. The results showed that the sonophotocatalytic oxidation of OMW was affected by the initial COD, acoustic power, temperature and TiO₂ concentration. The sonophotocatalytic oxidation of OMW increased with increasing the ultrasound power, temperature and H₂O₂ concentration. Sonolysis at frequency of 40 kHz combined with photocatalysis was not observed to have a significant effect on the OMW oxidation compared to sonication at frequency of 20 kHz. It was also found that the OMW oxidation was suppressed by the presence of the radical scavenger. The COD removal efficiency increased slightly with the increase of TiO₂ concentration up to certain point due to the formation of oxidizing species. At ultrasound frequency of 20 kHz, considerable COD reduction of OMW was reported, indicating the effectiveness of the combined US/UV/TiO₂ process for the OMW treatment.