Performance evaluation of chitosan-based flocculants with good pH resistance and high heavy metals removal capacity

Performance and mechanism of amphiphilic polymeric chelator for enhanced removal of high concentrations of Cu(II) from wastewater

An amphiphilic polymeric chelator (APC16-g-SX) grafted with sodium xanthate (SX) groups was successfully prepared for the efficient removal of high concentrations of Cu(II) from wastewater. The ordinary polymeric chelator (PAM-g-SX) based on linear polyacrylamide (PAM) was also prepared for comparative studies. The polymeric chelators were characterized by Fourier transform infrared spectroscopy (FT-IR), solid-state nuclear magnetic resonance (13C-NMR), gel permeation chromatography (GPC), elemental analyzer, and scanning electron microscope (SEM). The chelating performance of these polymeric chelators was investigated, and the mechanism of APC16-g-SX for enhanced removal of Cu(II) from wastewater was proposed based on fluorescence spectroscopy, cryo-scanning electron microscope (Cryo-SEM), energy-dispersive spectrometer (EDS), and X-ray photoelectron spectroscopy (XPS) tests. The results show that as the initial Cu(II) concentration in the wastewater increases, APC16-g-SX shows more excellent chelating performance than ordinary PAM-g-SX. For the wastewater with an initial Cu(II) concentration of 200 mg/L, the removal rate of Cu(II) was 99.82% and 89.34% for both 500 mg/L APC16-g-SX and PAM-g-SX, respectively. The pH of the system has a very great influence on the chelating performance of the polymeric chelators, and the increase in pH of the system helps to improve the chelating performance. The results of EDS and XPS tests also show that N, O, and S atoms in APC16-g-SX were involved in the chelation of Cu(II). The mechanism of enhanced removal of Cu(II) by APC16-g-SX can be attributed to the spatial network structure constructed by the self-association of hydrophobic groups that enhances the utilization of chelation sites.

Removal of lead in water by coagulation flocculation process using Cactus-based natural coagulant: optimization and modeling by response surface methodology (RSM)

The aim of this research is to study the ability of Cactus leaves to act as a biocoagulants for the removal of lead in water. Different solvents, such as distilled water, NaCl, NaOH, and HCl, were used as chemical activators to extract the active components from the Cactus. The Cactus was utilized as an organic coagulant in five different forms: (i) Cactus juice (CJ); Cactus extract using (ii) distilled water (C-H2O); (iii) NaCl at 0.5 M concentration (C-NaCl); (iv) NaOH at 0.05 M concentration (C-NaOH); and (v) HCl at 0.05 M concentration (C-HCl). In order to establish the optimal conditions for the coagulation, this study employed the jar test as an experimental technique and the Box-Behnken design (BBD) as an experimental approach. According to BBD, there are three factors (k = 3), namely pH, biocoagulant dosage, and settling time. The R2 and R2 adjusted for all coagulants were close to 100%, confirming the validity of all the mathematical models. The results were significant; the highest lead removal efficiencies were 98.11%, 98.34%, 95.65, 96.19%, and 97.49%, utilizing CJ, C-H2O, C-NaCl, C-HCl, and C-NaOH as natural coagulants. The Cactus has been characterized using FTIR, XRD, and SEM to identify the active components that remove lead.

Preparation and Application of Polyaluminum Ferric Sulfate from Red Mud: Behaviors of Leaching, Polymerizing, and Coagulation

Red mud is a solid waste containing valuable components, such as aluminum and iron. This paper aims to recover aluminum and iron from red mud by acid leaching and prepare polyaluminum ferric sulfate (PAFS) to apply for the turbidity reduction treatment of coal slurry water. The behaviors of leaching, polymerizing, and coagulation were analyzed by leaching thermodynamics and advanced micro-detection methods. More than 90% of aluminum and 60% of iron in red mud were dissolved into the leaching solution by using 50% sulfuric acid (v/v) with 7 mL/g at 100 °C for 2 h, where the crystal lattice of cancrinite was significantly destroyed to promote the dissolution of aluminum. The low polymerization (Al + Fe)a, medium polymerization (Al + Fe)b, and high polymerization (Al + Fe)c could be generated in PAFS by adjusting the basicity of the leaching solution with 0.7-0.9. The removal efficiency of turbidity of wastewater could reach more than 95% by using PAFS at 25 mg/L in the pH range of 6.0-7.0. The turbidity reduction mechanism included not only the electric neutralization of (Al + Fe)a but also the adsorption of (Al + Fe)b and the entrapment effect of (Al + Fe)c. This current study contributes to the future development of red mud based on flocculants containing aluminum and iron for wastewater treatment.

Kinetics of glyphosate and aminomethylphosphonic acid sorption onto montmorillonite clays in soil and their translocation to genetically modified corn

The co-occurrence of glyphosate (GLP) and aminomethylphosphonic acid (AMPA) in contaminated water, soil, sediment and plants is a cause for concern due to potential threats to the ecosystem and human health. A major route of exposure is through contact with contaminated soil and consumption of crops containing GLP and AMPA residues. However, clay-based sorption strategies for mixtures of GLP and AMPA in soil, plants and garden produce have been very limited. In this study, in vitro soil and in vivo genetically modified corn models were used to establish the proof of concept that the inclusion of clay sorbents in contaminated soils will reduce the bioavailability of GLP and AMPA in soils and their adverse effects on plant growth. Effects of chemical concentration (1-10 mg/kg), sorbent dose (0.5%-3% in soil and 0.5%-1% in plants) and duration (up to 28 days) on sorption kinetics were studied. The time course results showed a continuous GLP degradation to AMPA. The inclusion of calcium montmorillonite (CM) and acid processed montmorillonite (APM) clays at all doses significantly and consistently reduced the bioavailability of both chemicals from soils to plant roots and leaves in a dose- and time-dependent manner without detectable dissociation. Plants treated with 0.5% and 1% APM inclusion showed the highest growth rate (p ≤ 0.05) and lowest chemical bioavailability with up to 76% reduction in roots and 57% reduction in leaves. Results indicated that montmorillonite clays could be added as soil supplements to reduce hazardous mixtures of GLP and AMPA in soils and plants.

Lead-imprinted polyvinylidene fluoride membrane for selective removal of lead from contaminated water: material fabrication, filtration application, and mechanism study

The drinking water has become contaminated with lead in many countries across the world. In this study, a novel lead-imprinted polyvinylidene fluoride (PVDF) membrane was successfully fabricated for selective decontamination of lead from water. First of all, the membrane fabrication process was explored and optimized. The physical and chemical properties were then studied for a better understanding of the features of the membrane. The performance of lead removal by the adsorptive membrane was evaluated by systematic batch adsorption experiments, including pH effect, kinetics, isotherm, selectivity, and regeneration studies. The results indicated that the adsorptive membrane showed a high adsorption capacity of 40.59 mg Pb/g at the optimal pH of 5.5, fast kinetics of 2 h, high selectivity towards lead, and outstanding regeneration performance. The Langmuir equation fitted the isotherm better than the Freundlich equation, while the pseudo-second-order model and pore diffusion model well described the kinetics. The adsorptive membrane showed high selectivity towards lead in the lead/zinc binary solution. In the continuous filtration study, a small piece of adsorptive membrane could treat 3.75 L of lead solution. The XPS studies revealed that the lead uptake was mainly due to the complex reaction between lead and carboxyl and hydroxyl in the membrane.

Preparation of Heavy Metal Trapping Flocculant Polyacrylamide-Glutathione and Its Application for Cadmium Removal from Water

In this study, a heavy metal trapping gel with multiple ligand groups was prepared for the first time using response surface methodology. The gel was produced by condensing and grafting glutathione as a grafting monomer onto the main polyacrylamide chain, based on the Mannich reaction mechanism with formaldehyde. FTIR, SEM, TG-DSC, and zeta potentials were used to characterize the gel. The results demonstrated that the gel was morphologically folded and porous, with a net-like structure, which enhanced its net trapping and sweeping abilities, and that glutathione was used to provide sulfhydryl groups to boost the metal trapping ability of polyacrylamide. Coagulation experiments showed that the highest efficiency of the removal of Cd ions from water samples was achieved when the concentration of polyacrylamide-glutathione was 84.48 mgL^-1, the concentration of Cd was 10.0 mgL^-1, the initial turbidity was 10.40 NTU, and the initial pH was 9.0. Furthermore, the presence of two cations, Cu and Zn, had an inhibitory effect on the removal of Cd ions. In addition, analysis of the zeta potential revealed the flocculation of polyacrylamide-glutathione. The flocculation mechanism of glutathione is mainly chelation, adsorption bridging, and netting sweeping.

Adsorption and detoxification of glyphosate and aminomethylphosphonic acid by montmorillonite clays

The co-occurrence of mixtures of glyphosate (GLP) and aminomethylphosphonic acid (AMPA) in contaminated water, soil, sediment, and plants is a cause for concern due to potential threats to the ecosystem and human health. Major routes of exposure include contact with contaminated water and soil and through consumption of crops containing GLP and AMPA residues. Calcium montmorillonite (CM) and acid-processed montmorillonite (APM) clays were investigated for their ability to tightly sorb and detoxify GLP and AMPA mixtures. In vitro adsorption and desorption isotherms and thermodynamic analysis indicated saturable Langmuir binding of both chemicals with high capacities, affinities, enthalpies, and free energies of sorption and low desorption rates. In silico computational modeling indicated that both GLP and AMPA can be readily absorbed onto clay surfaces through electrostatic interactions and hydrogen bonding. The safety and efficacy of the clays were confirmed using well-established living organisms, including an aquatic cnidarian (Hydra vulgaris), a soil nematode (Caenorhabditis elegans), and a floating plant (Lemna minor). Low levels of clay inclusion (0.05% and 0.2%) in the culture medium resulted in increased growth and protection against chemical mixtures based on multiple endpoints. Results indicated that montmorillonite clays may be used to bind mixtures of GLP and AMPA in water, soil, and plants.

Potential application of spent mushroom compost (SMC) biochar as low-cost filtration media in heavy metal removal from abandoned mining water: a review

Overpopulation and rapid development have put an increasing burden on the environment, leading to various water crisis. Importing water from abandoned mines as an alternative raw water source could be the next answer to alleviate water scarcity problems globally. However, due to its high heavy metals content, there is a need to find an economical and effective method to remove heavy metals before reusing it as potable water source. Biochar, a low-cost and carbon-rich biosorbent, has received increasing attention on its application as a remediating agent to remove heavy metals from water. Previous studies have revealed the potential properties of biochar as a heavy metal removal agent including high cation exchange capacity, high surface area, active surface functional groups, as well as efficient adsorption. Apparently, the most important factor influencing the sorption mechanism is the type of feedstock materials. Spent mushroom compost (SMC), a waste product from mushroom cultivation, has been found as an excellent biosorbent. SMC has received global attention as it is low cost and eco-friendly. It also has been proved as an efficient heavy metals remover from water. Nevertheless, its application as biochar is still scarce. Therefore, this review focuses on the potential of transforming SMC into modified biochar to remove heavy metals, especially from abandoned mining water. The present review emphasizes the current trends in adsorption methods for heavy metal removal from water, assembles data from previous studies on the feedstock of biosorbents to biochars, and discusses the potentials of SMC as a biochar for water treatment.

Screening of Spirulina strains for high copper adsorption capacity through Fourier transform infrared spectroscopy

Microalgae have emerged as promising biosorbents for the removal of toxic metals from industrial effluents due to the presence of various free functional groups. While the constitutes are distinct among different algal strains, it needs to screen the algae with high adsorption capacities for heavy metal ions by analyzing the algal components. In this study, a rapid and nondestructive Fourier transform infrared (FTIR) method combined PCA algorithm was used to discriminate algal strains according to their cellular components. With FTIR spectroscopy, we have found that the algal strains for high copper adsorption capacity (RH44, XS58, AH53, and RZ22) can be well differentiated from other strains via assessing the components involved in the biosorption of copper ions at the spectral window range of 1,200–900 cm⁻¹ mainly attributed to polysaccharides. Correspondingly, the copper removal efficiency by different Spirulina strains was also measured by biochemical assay and scanning electron microscopy (SEM) in order to confirm the screening result. Compared with the chemical measurement, the assessment based on spectral features appears fairly good in the evaluation and differentiation of copper adsorption capacity in various Spirulina strains. This study illustrates that FTIR spectroscopy may serve as a fast and effective tool to investigate the functional groups for copper ions binding in the Spirulina cell and it even offers a useful and accurate new approach to rapidly assess potential adsorbents for the high capacity of copper adsorption.

Adsorption and interaction mechanisms of Chi-g-P(AM-DMDAAC) assisted settling of kaolinite in a two-step flocculation process

Flocculation has been widely employed in treatment of mineral tailings and water management. In this study, a chitosan-graft-poly(acrylamide-dimethyl diallyl ammonium chloride) (Chi-g-P(AM-DMDAAC)) was synthesized in-house. The adsorption and interaction mechanisms of Chi-g-P(AM-DMDAAC) and an anionic polyacrylamide (APAM) in a two-step flocculation process of kaolinite were explored using settlement tests, zeta potential measurement, quartz crystal micro-balance with dissipation (QCM-D) and atomic force microscopy (AFM) technique. The type of primary flocculant was critical for the two-step flocculation process. The treatment of the kaolinite suspension using 1 mg/L of Chi-g-P(AM-DMDAAC) followed by adding 2 mg/L of APAM displayed more efficient flocculation performance. QCM-D results showed that three dissipative layers were assembled on model kaolinite surface after sequentially injecting 3.5 mg/L of Chi-g-P(AM-DMDAAC), 0.05 wt% kaolinite suspension and 2.5 mg/L of APAM. The above total adsorption amount (Δf of -64.9 Hz) was much higher than that of using the two flocculants in reverse order (Δf of -23.1 Hz). This result indicated that the adsorption layer of the positively charged Chi-g-P(AM-DMDAAC) on kaolinite surface provided active adsorption sites for APAM. Further AFM measurement confirmed that the average adhesion between the silicon tip adsorbed Chi-g-P(AM-DMDAAC) and model kaolinite surface in 2.5 mg/L APAM solution increased from 0.25 ± 0.1 nN to 4.2 ± 0.3 nN with the effective interaction range of 700 nm, which was stronger than that measured between a bare silicon tip and silica substrate in single-component-flocculant solutions. The highly efficient two-step flocculation process could be ascribed to the strong electrostatic attraction between the kaolinite and the oppositely charged Chi-g-P(AM-DMDAAC) and APAM. Findings in this study will benefit the development of environmentally friendly flocculant for mineral tailings and water treatment.

Sustainable and efficient technologies for removal and recovery of toxic and valuable metals from wastewater: Recent progress, challenges, and future perspectives

Due to their numerous effects on human health and the natural environment, water contamination with heavy metals and metalloids, caused by their extensive use in various technologies and industrial applications, continues to be a huge ecological issue that needs to be urgently tackled. Additionally, within the circular economy management framework, the recovery and recycling of metals-based waste as high value-added products (VAPs) is of great interest, owing to their high cost and the continuous depletion of their reserves and natural sources. This paper reviews the state-of-the-art technologies developed for the removal and recovery of metal pollutants from wastewater by providing an in-depth understanding of their remediation mechanisms, while analyzing and critically discussing the recent key advances regarding these treatment methods, their practical implementation and integration, as well as evaluating their advantages and remaining limitations. Herein, various treatment techniques are covered, including adsorption, reduction/oxidation, ion exchange, membrane separation technologies, solvents extraction, chemical precipitation/co-precipitation, coagulation-flocculation, flotation, and bioremediation. A particular emphasis is placed on full recovery of the captured metal pollutants in various reusable forms as metal-based VAPs, mainly as solid precipitates, which is a powerful tool that offers substantial enhancement of the remediation processes' sustainability and cost-effectiveness. At the end, we have identified some prospective research directions for future work on this topic, while presenting some recommendations that can promote sustainability and economic feasibility of the existing treatment technologies.

Prospects of titanium carbide-based MXene in heavy metal ion and radionuclide adsorption for wastewater remediation: A review

Contamination of water sources with various organic and inorganic non-biodegradable pollutants is becoming a growing concern due to industrialization, urbanization, and the inefficiency of traditional wastewater treatment processes. Transition Metal Carbides/Nitrides (MXenes) are emerging as advanced nanomaterials of choice for treating contaminated water owing to their excellent conductivity, mechanical flexibility, high specific surface area, scalable production, rich surface functionalities, and layered morphology. MXenes have demonstrated enhanced ability to adsorb various organic and inorganic contaminants depending upon their surface terminal groups (-OH, -F, and -O) and interlayer spacing. Titanium carbide (Ti₃C₂T_x) is most researched to date due to its ease of processing and stability. Ti₃C₂T_x has shown excellent performance in absorbing heavy metal ions and radioactive heavy metals. This review summarizes state-of-the-art Ti₃C₂T_x synthesis, including selective etching techniques, optimization of the desired adsorption features (controlling surface functional groups, intercalation, sonication, and functionalization), and regeneration and adsorption mechanism to remove contaminants. Furthermore, the review also compares the adsorption performance of Ti₃C₂T_x with other commercial adsorbents (including chitosan, cellulose, biomass, and zeolites). Ti₃C₂T_x has been found to have an adsorption efficiency of more than 90% in most studies due to its layered structure, which makes the functional groups easily accessible, unique and novel compared to other conventional nanomaterials and adsorbents. The challenges, potential solutions, and prospects associated with the commercial development of Ti₃C₂T_x as adsorbents are also discussed. The review establishes a framework for future wastewater treatment research using MXenes to address the global problem of water scarcity.

Evaluating the performance of bridging-assembly chelating flocculant for heavy metals removal: Role of branched architectures

A novel chelating flocculant with branched architectures, polyacrylamide grafted maleoyl chitosan-mercaptoacetic acid (PAM-g-M(CS-MA)), was successfully fabricated using maleic anhydride as the "bridge" between chitosan and polyacrylamide. The functional groups and structural characteristic information of copolymers were obtained via characterization analysis. Flocculation performance was systematically investigated via purifying a series of simulated wastewater containing Cu or Cd. The properties of the flocs were studied to give in-depth evidences for the role of chelation groups and branched architectures in flocculation. Results indicated that PAM-g-M(CS-MA) showed excellent flocculation capacity for heavy metals in high concentrations and was superior to other chelating flocculants. The maximum flocculation efficiency of Cu (93.90%) and Cd (92.47%) was achieved by PAM-g-M(CS-MA) at pH 7, dosage of 100 mg L^-1 and stirring speed of 90 rpm. The flocculation mechanisms of PAM-g-M(CS-MA) were deeply explored through the analyses of floc properties. The strong synergistic chelation of mercapto, carboxyl, amide and hydroxyl groups predominated for the capturing of heavy metals; and the branched architectures facilitated the formation of large and stable flocs via adsorption and bridging-furl effect. This study provided a solid foundation for the fabrication of flocculants for heavy metal wastewater treatment.

Advanced Treatment of Phosphorus Pesticide Wastewater Using an Integrated Process of Coagulation and Ozone Catalytic Oxidation

Conventional pretreatment and secondary biochemical treatment are ineffective methods for removing phosphorus from phosphorus-containing pesticide wastewater. In this study, coagulation-coupled ozone catalytic oxidation was used to treat secondary biochemical tailwater of phosphorus-containing pesticide wastewater thoroughly. The effects of the coagulant type, coagulant dosage, coagulant concentration, wastewater pH, stirring rate, and stirring time on the removal efficiency of chemical oxygen demand (COD), total phosphorus (TP), and chromaticity were investigated during coagulation. When the dosage of the coagulant PAFS was equal to 100 mg/L, the concentration of the coagulant, pH, stirring rate, and stirring time were 5 wt%, 8, 100 rpm, and 5 min, respectively, and the removal rates of COD, TP, and chroma in wastewater reached the maximum value of 17.6%, 86.8%, and 50.0%, respectively. Effluent after coagulation was treated via ozone catalytic oxidation. When the respective ozone dosage, H2O2 dosage, catalyst dosage, and reaction time were 120 mg/L, 0.1 vt‰, 10 wt%, and 90 min, residual COD and chromaticity of the final effluent were 10.3 mg/L and 8, respectively. The coagulation-coupled ozone catalytic oxidation process has good application prospects in the treatment of secondary biochemical tailwater from phosphorus-containing pesticide wastewater.

Characterization and evaluation of adsorption potential of chitosan impregnated cellulose nanofiber / multi-walled carbon nanotubes aerogel for copper ions

The development of aerogel materials with high preparation efficiency, no pollution, and high adsorption efficiency was still an effective solution for water pollution caused by heavy metal ions. This paper...

Flocculation of combined contaminants of dye and heavy metal by nano-chitosan flocculants

In this study, two multifunctional nano-chitosan flocculants (CPAM-NCS1 and CPAM-NCS2) were made through the graft modification of cationic monomer and carboxymethylchitosan (CMCTS) to remove combined contaminants. The effects of various factors (pH, flocculant dosage and hydraulic mixing conditions) on the flocculation performance under single and composite pollution conditions were systematically investigated, the optimal chemical oxygen demand (COD) and the chromaticity removal rates in the dye wastewater were 79.9% and 83.9% at wastewater pH 7, the fast stirring rate 300 rpm, the fast stirring time 8 min, and the dosage of CPAM-NCS1 80 mg/L, respectively. The optimal removal rates of Cu (II) obtained by CPAM-NCS1 and CPAM-NCS2 at were 80.3% and 75.2% at 60 mg/L and the wastewater pH 7, respectively. The optimal removal rates of Cu (II) and disperse orange were 85.3% and 89.4%, respectively, in a composite pollutant system in which Cu (II) and disperse orange coexisted when the pH of the composite system was 9 and the dosage of CPAM -NCS1 was 60 mg/L. This study proved that nanoflocculants made by modifying CMCTS with different structures can demonstrate ideal flocculation removal performance for dye and heavy metal wastewaters.

Low-pressure UV-initiated synthesis of cationic starch-based flocculant with high flocculation performance

A kind of starch-based flocculant (starch-graft-poly[(2-methacryloyloxyethyl) trimethyl ammonium chloride], denoted St-g-PDMC-LPUV) has been synthesized by low-pressure ultraviolet initiation and was employed to remove humic acid (HA) for water purification. The physicochemical characteristics of starch and St-g-PDMC-LPUV were characterized by FT-IR, ¹H NMR, XRD, TGA, SEM and BET to confirmed the successful grafting DMC onto starch. Effects of flocculant dosage, pH, the adding amount of Fe₃O₄, initial HA concentration and stirring speed were investigated systematically. The prepared St-g-PDMC-LPUV flocculant with non-toxic, biodegradability and environmental friendliness exhibited effective performance for removing HA from water in a wide pH range (5-10). The flocculation mechanism was attributed to the effective collision between function groups of the St-g-PDMC-LPUV flocculant and HA by charge neutralization, adsorption, bridging and patching.

Removal of Cd (II) Ions from Bioretention System by Clay and Soil Wettability

In this work, a silane modifier with benzyl substitutes (OFS-B) and linear substitutes (OFS-L) was used to modify bentonite clay and soil, and the results were characterized by Fourier transform-infrared absorption spectroscopy (FT-IR) and powder-X-ray diffraction (XRD) analysis. A contact angle analysis was performed to determine the wettability of modified clay and soil. The findings revealed that silane-modified OFS-L clay and soil produced wettable surfaces, while OFS-B exhibited hydrophobic properties. These clays and soils were used in a bioretention system for Cd (II) removal. In the study, seven different types of bioretention systems, including natural, OFS-L, and OFS-B modified clay and soil, as well as natural, OFS-L, and OFS-B modified soil, were applied to Cyperus alternifolius plants without an additional layer. The removal capacity of Cd (II) was measured in the following order: modified clay > modified soil > original clay/soil > no layer, i.e., 99.48%, 92.22%, 88.10/78.5%, and 30.0%, respectively. OFS-L removed more Cd (II) than OFS-B during the modification. OFS-L now improves the bioavailability and accumulation of Cd (II) in the plant (18.5 µg/g) and has a higher chlorophyll-b concentration (1.92 mg/g fresh weight) than other systems. The wettable clay exhibited clay leaching into the various levels of the bioretention system. In the bioretention system, benzyl substituted clay prevented the penetration of water and formed a Cd (II) agglomeration. When compared to non-wettable modifiers, these results indicated that wettable clay material could be a capable material for removing Cd (II).

Heavy metal removal from aqueous solutions by chitosan-based magnetic composite flocculants

In this study, three magnetic flocculants with different chelating groups, namely, carboxymethyl chitosan-modified Fe₃O₄ flocculant (MC), acrylamide-grafted magnetic carboxymethyl chitosan flocculant (MCM), and 2-acrylamide-2-methylpropanesulfonic acid copolyacrylamide-grafted magnetic carboxymethyl chitosan flocculant (MCAA) were prepared, synthesized, and characterized by photopolymerization technology. They were applied to the flocculation removal of Cr(III), Co(II), and Pb(II). The effect of flocculation condition on the removal performance of Cr(III), Co(II), and Pb(II) was studied. Characterization results show that the three magnetic carboxymethyl chitosan-based flocculants have been successfully prepared with good magnetic induction properties. Flocculation results show that the removal rates of MC, MCM, and MCAA on Cr(III) are 51.79%, 82.33%, and 91.42%, respectively, under the conditions of 80 mg/L flocculant, pH value of 6, reaction time of 1.5 hr, G value of 200 s^-1, and precipitation magnetic field strength of 120 mT. The removal rates of Co(II) by MC, MCM, and MCAA are 54.33%, 84.99%, and 90.49%, respectively. The removal rates of Pb(II) by MC, MCM, and MCAA are 61.54%, 91.32%, and 95.74%, respectively. MCAA shows good flocculation performance in composite heavy metal-simulated wastewater. The magnetic carboxymethyl chitosan-based flocculant shows excellent flocculation performance in removing soluble heavy metals. This research provides guidance and ideas for the development of efficient and low-cost flocculation technology to remove heavy metals in wastewater.

Biopolymer-based flocculants: a review of recent technologies

Biopolymer-based flocculants have become a potential substitute for inorganic coagulants and synthetic organic flocculants due to their wide natural reserves, environmental friendliness, easy natural degradation, and high material safety. In recent years, with more and more attention to clean technologies, a lot of researches on the modification and application of biopolymer-based flocculants have been carried out. The present paper reviews the latest important information about the base materials of biopolymer-based flocculants, including chitosan, starch, cellulose, and lignin etc. This review also highlights the various modification methods of these base materials according to reaction types in detail. Via the recent researches, the flocculation mechanisms of biopolymer-based flocculants, such as adsorption, bridging, charge neutralization, net trapping, and sweeping, as well as, some other special mechanisms are comprehensively summarized. This paper also focuses on the water treatment conditions, the removal efficiency, and advantages of biopolymer-based flocculants in applications. Further, this review sheds light on the future perspectives of biopolymer-based flocculants, which may make progress in the sources of base materials, modification processes, multi-function, and deepening application researches. We believe that this review can guide the further researches and developments of biopolymer-based flocculants in the future, to develop them with a higher efficiency, a lower cost, more safety, and multi-function for more diversified applications. Graphical abstract.

Effective removal of heavy metals from water using porous lignin-based adsorbents

Multifunctional composite materials are the key to improving removal capacity and environmental utility. Here, the adsorbent (SLCA) was obtained by free-radical polymerization of acrylic acid with sodium lignosulfonate and citric acid. FTIR, SEM, TGA and XPS characterization methods were used to prove the structure and properties of SLCA adsorbents. The maximum uptake capacities of the optimized SLCA adsorbent is 276 mg g^-1 of Cu²⁺ and 323 mg g^-1 of Pb²⁺, respectively. The Langmuir isotherm and the second-order kinetic model were established to illustrate that the capture of Cu²⁺ and Pb²⁺ by the adsorbent belongs to chemisorption on the monolayer. XPS analysis confirmed that complexation and electrostatic attraction are the mechanism of pollutant removal. Not only that, as-resulting adsorbent revealed no significant adsorption cycle efficiency reduction even after 5 runs of sorption-desorption cycle, manifesting that it is of great stability and could be regarded as a promising candidate adsorbent. The purpose of this research was to develop a green lignin-based adsorbent with strong environmental protection and regeneration ability based on cheap polyacrylic resin.

Preparation and Characterization of High-Efficiency Magnetic Heavy Metal Capture Flocculants

In this study, a high-efficiency magnetic heavy metal flocculant MF@AA was prepared based on carboxymethyl chitosan and magnetic Fe3O4. It was characterized by SEM, FTIR, XPS, XRD and VSM, and the Cu(II) removal rate was used as the evaluation basis for the preparation process. The effects of AMPS content, total monomer concentration, photoinitiator concentration and reaction time on the performance of MF@AA flocculation to remove Cu(II) were studied. The characterization results show that MF@AA has been successfully prepared and exhibits good magnetic induction characteristics. The synthesis results show that under the conditions of 10% AMPS content, 35% total monomer concentration, 0.04% photoinitiator concentration, and 1.5 h reaction time, the best yield of MF@AA is 77.69%. The best removal rate is 87.65%. In addition, the response surface optimization of the synthesis process of MF@AA was performed. The optimal synthesis ratio was finally determined as iron content 6.5%, CMFS: 29.5%, AM: 53.9%, AMPS: 10.1%. High-efficiency magnetic heavy metal flocculant MF@AA shows excellent flocculation performance in removing Cu(II). This research provides guidance and ideas for the development of efficient and low-cost flocculation technology to remove Cu(II) in wastewater.

Removal of Heavy Metals during Primary Treatment of Municipal Wastewater and Possibilities of Enhanced Removal: A Review

Resource reuse has become an important aspect of wastewater management. At present, use of sludge in agriculture is one of the major reuse routes. Conventional municipal wastewater treatment does not involve any designated process for removal of heavy metals, and these distribute mainly between effluent and sludge. Enhanced removal of heavy metals during primary treatment may decrease the heavy metal concentrations in both effluent and sludge from secondary treatment and promote long-term reuse of secondary sludge. This review considers heavy metal occurrence and removal during primary settling, together with possible treatment technologies for heavy metal removal in primary settlers and their theoretical performance. The variation in total heavy metal concentrations and dissolved fraction in raw municipal wastewater points to a need for site-specific assessments of appropriate technologies for improved heavy metal removal. Studies examining the heavy metal speciation beyond dissolved/particulate are few. Missing or disparate information on process parameters such as hydraulic retention time, pH and composition of return flows makes it hard to generalize the findings from studies concerning heavy metal removal in primary settlers. Coagulation/flocculation and use of low-cost sorbents were identified as the most promising methods for enhancing heavy metal removal during primary settling. Based on the available data on heavy metal speciation and removal during primary settling, sorption technologies may be most effective for enhancing the removal of Cu and Ni, while coagulation may be efficient for Cd, Cr, Cu, Pb, Zn and Hg removal (but not as efficient for Ni removal).

Removal of Cd(II) using dithiocarboxyl cornstalk and the waste filtrate

A novel adsorbent, called dithiocarboxyl cornstalk (DTCS), was developed, and the effects of various parameters on the adsorption performance for Cd(II) with DTCS were investigated in this work. The results suggested that DTCS presented the efficient removal capacity for Cd(II) when the pH values, adsorption temperature, and oscillation rate were 3.0 to 6.0, 313 K, and 150 rpm, respectively. The adsorption kinetic data were more agreed with pseudo-second-order kinetic model, and the isotherm data could be characterized by Freundlich model. The thermodynamic data indicated the adsorption process was endothermic and spontaneous. The FTIR and SEM confirmed the chemisorption between Cd(II) and DTCS. Furthermore, to eliminate the secondary pollution, the waste filtrate generated in the preparation of DTCS was employed to remove Cd(II) through flocculation experiments. The results showed that the waste filtrate is a potential flocculant for the treatment of wastewater containing Cd(II).

Magnetic flocculation of Cu(II) wastewater by chitosan-based magnetic composite flocculants with recyclable properties

In this study, three magnetic flocculants, namely, MC, MC-g-PAM, and MC-g-PAA, were prepared. The structure characteristics, flocculation performance, and floc characteristics of the three magnetic flocculants were systematically studied and compared. SEM, FT-IR, XPS, XRD, TG-DSC, and VSM characterization results show that MC, MC-g-PAM, and MC-g-PAA are successfully prepared and exhibit good magnetic induction. The removal rates of copper ions by MC, MC-g-PAM, and MC-g-PAA under the optimal coagulation conditions are 93.39 %, 88.64 %, and 61.41 %, respectively. Kinetic fitting shows that the flocculation reaction process of MC and MC-g-PAM conforms to pseudo first-order kinetics, while the flocculation reaction process of MC-g-PAA conforms to pseudo second-order kinetics. The flocs produced by MC-g-PAA have larger particle size and fractal dimension than those by MC and MC-g-PAM. At 80 mg/L dosage and pH 6, the floc size and floc fractal dimension obtained by MC-g-PAA reach the maximum values of 48.28 um and 1.468, respectively. Zeta potential studies show that the flocculation functions of the three flocculants are mainly adsorption bridging, adsorption electric neutralization, and chelating precipitation. Recycling experiments show that MC-g-PAA has good recyclability, and the recovery rate after the fifth use is 77.24 % with the Cu(II) removal rate of 67.53 %.

Excellent selectivity and high capacity of As (V) removal by a novel lignin-based adsorbent doped with N element and modified with Ca2

As one of the most significant natural polymer with the highest annual yield, lignin has been applied in the treatment of wastewater to remove heavy metal ions. However, there are still some shortages, such as low reactivity, difficulties in adsorbing oxyanions and low selectivity on specific oxyanions. To improve its adsorption properties, a novel lignin-based adsorbent was prepared in this study, doped with nitrogen by Mannich reaction, using triethylenetetramine (TETA) as N source, and further modified with Ca²⁺. The adsorption of Ca, N-co-doped lignin (Ca@N-Lig) for As (V), Cr (VI) and P (V) was studied. The Ca@N-Lig shows high capacity, excellent selectivity and prominent regeneration ability for As (V) adsorption. The adsorption of Ca@N-Lig for As (V) followed the Langmuir isotherm model and the pseudo-second-order kinetics model, yielding a maximum adsorption capacity of 681.59 mg·g^-1 and a fast adsorption equilibrium within 30 min. Ca@N-Lig has an excellent regeneration ability on the adsorption of As (V) with a decrease of about 15.60% after 5 adsorption/desorption cycles. This study offers an efficient way to remove As (V) from polluted water.

Synthesis and evaluation of cationic flocculant P(DAC-PAPTAC-AM) for flocculation of coal chemical wastewater

In this study, a high-efficiency cationic flocculant, P(DAC-MAPTAC-AM), was successfully prepared using UV-induced polymerization technology. The monomer Acrylamide (AM): Acryloxyethyl Trimethyl ammonium chloride (DAC): methacrylamido propyl trimethyl ammonium chloride (MAPTAC) ratio, monomer concentration, photoinitiator concentration, urea content, and cationic monomer DAC:MAPTAC ratio, light time, and power of high-pressure mercury lamp were studied. The characteristic groups, characteristic diffraction peaks, and characteristic proton peaks of P(DAC-MAPTAC-AM) were confirmed by fourier transform infrared spectroscopy (FTIR), X-Ray diffraction (XRD), ¹H nuclear magnetic resonance spectrometer (¹H NMR), and scanning electron microscopy (SEM). The effects of dosage, pH value, and velocity gradient (G) value on the removal efficiencies of turbidity, COD, ammonia nitrogen, and total phenol by poly aluminum ferric chloride (PAFC), P(DAC-MAPTAC-AM), and PAFC/P(DAC-MAPTAC-AM) in the flocculation treatment of coal chemical wastewater were investigated. Results showed that the optimal conditions for the flocculation of coal chemical wastewater using P(DAC-MAPTAC-AM) alone are as follows: dosage of 8-12 mg/L, G value of 100-250 s ^- 1, and pH value of 4-8. The optimal dosage of PAFC is 90-150 mg/L with a pH of 2-12. The optimal dosage for PAFC/P(DAC-MAPTAC-AM) is as follows: PAFC dosage of 90-150 mg/L, P(DAC-MAPTAC-AM) dosage of 8-12 mg/L, and pH range of 2-6. When P(DAC-MAPTAC-AM) was used alone, the optimal removal efficiencies of turbidity, COD, ammonia nitrogen, and total phenol were 81.0%, 35.0%, 75.0%, and 80.3%, respectively. PAFC has good tolerance to wastewater pH and good pH buffering. Thus, the flocculation treatment of coal chemical wastewater using the PAFC/P(DAC-MAPTAC-AM) compound also exhibits excellent resistance and buffering capacity.

Plant-Based Tacca leontopetaloides Biopolymer Flocculant (TBPF) Produced High Removal of Heavy Metal Ions at Low Dosage

High removal of heavy metals using plant-based bioflocculant under low concentration is required due to its low cost, abundant source, and nontoxicity for improved wastewater management and utilization in the water industry. This paper presents a treatment of synthetic wastewater using plant-based Tacca leontopetaloides biopolymer flocculant (TBPF) without modification on its structural polymer chains. It produced a high removal of heavy metals (Zn, Pb, Ni, and Cd) at a low concentration of TBPF dosage. In our previous report, TBPF was characterized and successfully reduced the turbidity, total suspended solids, and color for leachate treatment; however, its effectiveness for heavy metal removal has not been reported. The removal of these heavy metals was performed using a standard jar test procedure at different pH values of synthetic wastewater and TBPF dosages. The effects of hydroxide ion, pH, initial TBPF concentration, initial metal ion concentration, and TBPF dosage were examined using one factorial at the time (OFAT). The results show that the highest removal for Zn, Pb, Ni, and Cd metal ions were 98.4–98.5%, 79–80%, 97–98%, and 92–93%, respectively, using 120 mg/L dosage from the initial concentration of 10% TBPF at pH 10. The final concentrations for Zn, Pb, Ni, and Cd metal ions were 0.043–0.044, 0.41–0.43, 0.037–0.054, and 0.11–0.13 mg/L, respectively, which are below the Standard B discharge limit set by the Department of Environment (DOE), Malaysia. The results show that TBPF has a high potential for the removal of heavy metals, particularly Zn, Pb, Ni, and Cd, in real wastewater treatment.

Functionalized Glutathione on Chitosan-Genipin Cross-Linked Beads Used for the Removal of Trace Metals from Water

Functionalized glutathione on chitosan-genipin cross-linked beads (CS-GG) was synthesized and tested as an adsorbent for the removal of Fe(II) and Cu(II) from aqueous solution. The beads were characterized by several techniques, including Fourier-transform infrared spectroscopy (FTIR), thermogravimetric analysis (TGA), CNS elementary analysis, scanning electron microscopy (SEM), and atomic force microscopy (AFM). The effect of several parameters such as the pH, the temperature, and the contact time was tested to optimize the condition for the adsorption reaction. The beads were incubated in aqueous solutions contaminated with different concentrations of Fe(II) and Cu(II) (under the range concentration from 10 to 400 mg·L-1), and the adsorption capacity was evaluated by inductively coupled plasma optical emission spectrometry (ICP-OES). The adsorption equilibrium was reached after 120 min of incubation under optimal pH 5 for Fe(II) and after 180 min under optimal pH 6 for Cu(II). According to the Langmuir isotherm, the maximum adsorption capacities (q max) for Fe(II) and Cu(II) were 208 mg·g-1 and 217 mg·g-1, respectively. Our results showed that the adsorption efficiency of both metals on CS-GG beads was correlated with the degree of temperature. In addition, the adsorption reaction was spontaneous and endothermic, indicated by the positive values of ΔG 0 and ΔH 0. Therefore, the present study demonstrated that the new synthesized CS-GG beads had a strong adsorption capacity for Fe(II) and Cu(II) and were efficient to remove these trace metals from aqueous solution.

Kinetic study of removal heavy metal from aqueous solution using the synthetic aluminum silicate

One of the problems that most affect humanity today is the wastewater discharge into different water bodies. It was estimated that more than 7 million tons of wastewater are generated worldwide and are discharged into rivers, lakes, and reservoirs. Among the most dangerous wastewaters are those from inorganic chemistry research laboratories, mainly due to heavy metals. These problems have become a highly relevant topic, and numerous researchers have tried to design wastewater treatment systems that will deal more efficiently with heavy metals elimination. In this work, the synthesis, characterization, and evaluation of hydrated aluminium silicate were performed as alternative wastewater treatment from chemistry research and teaching laboratories. The compound obtained was [Formula: see text], which was characterized by the determination of its physicochemical properties. These revealed a low density, very porous material, with low crystallinity, strong chemical resistance, a large surface area, and a high apparent ionic exchange capacity. Absorption kinetics studies of heavy metals in aqueous solutions, through more widespread models, have demonstrated that [Formula: see text] has excellent properties as absorbents of this material. The amorphous hydrated aluminium silicate achieves a decrease in the concentration of all the metal ions studied, reducing them to discharge levels permissible.

Comparative study on Pb2+ removal from aqueous solutions using biochars derived from cow manure and its vermicompost

Waste emissions have increased the amount of water and soil contaminated with heavy metals such as Pb. To broaden the methods for the recycling and environmental usage of cow manure (CM) and its vermicompost (CV), CM, CV, and their derived biochars produced by the pyrolysis of CM or CV at 350 and 700 °C were used as adsorbents for Pb²⁺ removal in this batch adsorption experiment to reveal their different Pb²⁺ removal efficiencies and the underlying mechanisms. The batch experiment results revealed that all adsorbents rapidly removed Pb²⁺ within 30 min. A pH between 2.0 and 6.0 positively affected Pb²⁺ removal by CM and its biochar, whereas that by CV and its biochar was only positively affected by pH between 2.0 and 3.0. CV-derived biochar was more effective in the removal of Pb²⁺ than the other absorbents, with the maximum adsorption capacities (Qm) fitted from the Langmuir model reaching approximately 230.0 mg·g^-1 and the desorption rate (DR) being approximately 0.00-0.02%. Material physiochemical characterization, including X-ray diffraction analysis, showed that high pH, high ash content, rich mineral content, and high mineral contents might have been the main reasons for more effective removal of Pb²⁺ from aqueous solutions by CV-derived biochar. Fourier-transform infrared analysis indicated that surface functional groups such as -OH, CO, -COO-, and C-O; original and newly produced carbonate; and phosphate in CV also led to more effective Pb²⁺ removal efficiency from aqueous solution via surface functional group binding. Thus, pyrolyzing CVs may be used to produce biochar as a cost-effective adsorbent for heavy metal remediation in soil and water in the future.

Assessment of a novel nanostructured flocculant with elevated flocculation and antimicrobial activity

In this work, a novel process involving the preparation of nanochitosan-grafted flocculants (CPAM-g-NCS) to treat low turbid and salmonella suspensions simultaneously was introduced. Nanotechnology was employed to enhance the adsorption-adhesion and sterilization abilities of dual-functional flocculants. The monomers of chitosan, acrylamide, methacryloyl ethyl trimethyl ammonium chloride, and sodium tripolyphosphate were utilized for flocculants copolymerization. Then, using fourier-transform infrared spectroscopy, nuclear magnetic resonance hydrogen spectrum, and thermogravimetric and differential scanning calorimetry analysis, the successful synthesis of CPAM-g-NCS was verified. Scanning electron microscopy and size analysis suggested that nanostructured flocculants with irregular morphology and nanocolloids of 60.44 nm were formed. CPAM-g-NCS was applied to treat a series of simulated low turbid and salmonella suspensions. The simulation results showed that the minimum residual turbidity of 1.97 NTU and optical density of 0.16 (initial 0.89) can be achieved at dosages of 2.5 and 8.75 mg L^-1, respectively, which were superior to conventional organics flocculants. Mechanistic studies suggested that the excellent adsorption property, and large numbers of quaternary ammonium and amino groups of nanoflocculants contributed to the superior flocculation and antibacterial performance of CPAM-g-NCS.

Removal of copper and cadmium ions from alkaline solutions using chitosan-tannin functional paper materials as adsorbent

We successfully absorbed the copper ion (Cu²⁺) and cadmium ion (Cd²⁺) from alkaline aqueous solutions using the prepared chitosan-tannin (CTS/TA) functional paper as absorbent materials. The kinetics of the adsorption, the adsorption isotherms, and the influence of the solution flow rate and pH were investigated detailly. The adsorption data were described well by Langmuir isotherms, with maximum copper (Cu²⁺) and cadmium (Cd²⁺) adsorption capacities of 684.93 and 813.01 mg/m², respectively. The experimental results also showed that the adsorption of these heavy metals was selective in the order of Cu²⁺ > Cd²⁺, as Cu²⁺ competed with Cd²⁺ for bonding sites at solution concentrations greater than or equal to 200 mg/L. The results of this study illustrated that the chitosan-tannin functional paper materials mainly followed a complexation-adsorption model, and the best adsorption capacity was achieved at pH = 9. The desorption of heavy ions from this adsorbent and its reusability of functional paper was also involved. Therefore, this novel, environment-friendly functional paper can surely act as an effective adsorbent for the removal and recovery of heavy metals in alkaline aqueous solutions.