A review on phenolic wastewater remediation using homogeneous and heterogeneous enzymatic processes: Current status and potential challenges

Rapid Peracetic acid activation by CoO under neutral condition: The contribution of multiple reactive species

This paper proposes a novel process of cobalt monoxide (CoO)-activated peracetic acid (PAA) for treating emerging micropollutant in water. PAA was activated under neutral conditions by combining a dominant heterogeneous phase on the catalyst surface and a homogeneous phase by dissolved Co2+. The system produced several reactive oxygen species, including hydroxyl radicals (HO∙HO•), singlet oxygen (1O2), organic radicals (RO•(CH3C(O)O•, CH3C(O)OO•) and high-valent cobalt (Co(IV)). Organic radicals and high-valent cobalt primarily drove the emerging micropollutants degradation, interacting via electron transfer. Further density functional theory calculations supported that the spontaneous adsorption of PAA onto the catalyst could break peroxy bonds that generate radicals. Furthermore, the CoO surface structure underwent minimal changes during the reaction, making it highly reusable. Thus, the novel CoO/PAA system could be an effective advanced oxidation process for water treatment.

Analysis of small three-dimensional fluorescence spectroscopy dataset using migration learning an example of phenol concentration prediction in wastewater

Three-dimensional fluorescence spectroscopy has been widely used to detect organic pollutants in water. However, the amount of data required for three-dimensional fluorescence spectroscopy analysis is relatively large, and the time cost of sample collection is high. The amount of data has become an unavoidable limitation of spectral analysis. This study takes the detection of phenol in industrial discharge wastewater as an example and proposes a transfer learning method for small fluorescence spectroscopy datasets. First, fluorescence spectra are generated by splitting them into linear combinations of positively and negatively distributed spectra. Then, based on the idea of transfer learning, the generated fluorescence spectra are used to train a task-specific pre-trained model, which is then transferred to the collected spectral dataset. Experimental results show that the prediction performance of the transfer learning method is improved by 50.08 % compared with that obtained by directly training the model using a small amount of spectral data. In addition, when the spectral data remains unchanged, the accuracy of the model can be improved to a certain extent by increasing the amount of spectral data used for pre-training. The transfer learning method proposed in this study further improves the prediction accuracy when data is limited, and the results of verification in real environments are also satisfactory. It provides a feasible solution to the problem of data limitations in three-dimensional fluorescence spectroscopy.

Electrochemical conversion of CO2 using metalorganic frameworks-based materials: A review on recent progresses and outlooks

Global warming has been mainly attributed to the excessive release of carbon dioxide (CO2) to the atmosphere. Several CO2 capture and conversion technologies have been developed in the past few decades with their own merits and limitations. Electrochemical conversion of CO2 is one of the most attractive techniques for combating CO2 emissions. However, the efficacy of the electrochemical reduction of CO2 hinges on the efficiency of the utilized materials (i.e., electrocatalysts). Metal organic frameworks (MOFs)-based materials have recently emerged as attractive tools for various applications, including the electrochemical conversion of CO2. Although there are some review articles on CO2 capture and conversion using different materials, reviews focusing specifically on the electrochemical conversion of CO2 using MOFs-based materials are still comparatively lacking. Additionally, the field of electrochemical conversion of CO2 into valuable chemicals is currently gaining high momentum, requiring comprehensive and recent reviews, which would provide researchers/professionals with a quick and easy access to the recent developments in this rapidly evolving research area. Accordingly, this article comprehensively reviews recent studies on the electrochemical conversion of CO2 using pristine/modified/functionalized MOFs as well as composite materials containing MOFs. Additionally, single atom catalysts (SACs) derived from MOFs and their applications for the electrochemical conversion of CO2 has also been reviewed. Furthermore, obstacles, challenges, limitations, and remaining research gaps have been identified, and future works to tackle them have been highlighted. Overall, this review article provides valuable discussion and insights into the recent advancements in the field of electrochemical conversion of CO2 into chemicals using MOFs-based materials.

Regulating iron center by defective MoS2 for superior Fenton-like catalysis in water purification: The key role of surface interaction and superoxide radical in accelerating metal redox-cycling

Transition metals exhibit high reactivity for Fenton-like catalysis in environmental remediation, but how to save consumption and reduce pollution is of great interest. In this study, rationally designed defect-engineered Fe@MoS2 (Fe@D-MoS2) was prepared by incorporating reactive iron onto structural defects generated from the chemical acid-etching, aiming to improve the energetic consumption of the catalyst in Fenton-like applications. Morphological and structural properties were elucidated in details, the Fenton-like reactivity was evaluated with five phenolic contaminants for oxidant activation, radical generation and environmental remediation. Compared to Fe@MoS2, Fe@D-MoS2 exhibited a 18.9-fold increase in phenol degradation (0.09 versus 1.79 min-1). Quenching experiments, electron paramagnetic resonance tests and electrochemical measurements revealed the dominant sulfate and superoxide radicals. Rendered by strong metal-substrate surface and electronic interactions from regulated chemical environment and coordination structure, the inert ≡ Fe(III) was reduced to the reactive ≡ Fe(II) accompanied by the ≡ Mo(IV) oxidation to ≡ Mo(V) in MoS2 lattice, with adjacent sulfur serving as the key electron transfer bridge. Therefore, this work shows that the incorporation of reactive centers is able to boost two-dimensional sulfide materials for environmental catalysis applications.

Biodegradation of phenol-contaminated soil and plant growth promotion by Myroides xuanwuensis H13

Physicochemical methods for remediating phenol-contaminated soils are costly and inefficient, making biodegradation an environmentally friendly alternative approach. This study aims to screen for potential phenol-degrading bacteria and to verify the removal capacities of a selected strain in a bioaugmentation experiment at the greenhouse level using Brassica chinensis L. (Chinese cabbage) as the model plant and phenol-contaminated soil. In parallel, pot experiments were conducted using a collaborative approach based on this model system. We found that Myroides xuanwuensis strain H13 showed a high degradation capability, with a 97.67% efficiency in degrading 100 mg/L phenol. Under shaking flask conditions, H13 facilitated the solubilization of tricalcium phosphate and potassium feldspar powder. Pot experiments suggested a phenol removal percentage of 89.22% and enhanced availability of soil phosphorus and potassium for plants with H13 inoculation. In this case, the abundance of soil microbes and the activity of soil enzymes significantly increased as well. Furthermore, both photosynthesis and the antioxidant system in Chinese cabbage were enhanced following H13 inoculation, resulting in its increased yield and quality. Partial least squares path modeling revealed that H13 can primarily affect plant root growth, with a secondary impact on photosynthesis. These findings highlight the potential of biodegradation from phenol-degrading bacteria as a promising strategy for efficient phenol removal from soil while promoting plant growth and health.IMPORTANCEThis study is significant for environmental remediation and agriculture by its exploration of a more environmentally friendly and cost-effective bio-strategy in treating phenol-contaminated soil. These findings have essential implications for environmental remediation efforts and sustainable agriculture. By utilizing the biodegradation capabilities of Myroides xuanwuensis strain H13, it is possible to remove phenol contaminants from the soil efficiently, reducing their negative effects. Furthermore, the enhanced growth and health of the Chinese cabbage plants indicate the potential of this approach to promote sustainable crop production.

Magnetic nanoflowers: a hybrid platform for enzyme immobilization

The use of organic-inorganic hybrid nanoflowers as a support material for enzyme immobilization has gained significant attention in recent years due to their high stability, ease of preparation, and enhanced catalytic activity. However, a major challenge in utilizing these hybrid nanoflowers for enzyme immobilization is the difficulty in handling and separating them due to their low density and high dispersion. To address this issue, magnetic nanoflowers have emerged as a promising alternative enzyme immobilization platform due to their easy separation, structural stability, and ability to enhance catalytic efficiency. This review focuses on different methods for designing magnetic nanoflowers, as well as future research directions. Additionally, it provides examples of enzymes immobilized in the form of magnetic nanoflowers and their applications in environmental remediation, biosensors, and food industries. Finally, the review discusses possible ways to improve the material for enhanced catalytic activity, structural stability, and scalability.

Design of a two functional permeable reactive barrier for synergistic enzymatic and microbial bioremediation of phenol-contaminated waters: laboratory column evaluation : Enzymatic and microbial bioremediation of phenol in a bilayer permeable reactive barrier

The present study aimed to develop a system using a combination of enzymatic and microbial degradation techniques for removing phenol from contaminated water. In our prior research, the HRP enzyme extracted from horseradish roots was utilized within a core-shell microcapsule to reduce phenolic shock, serving as a monolayer column. To complete the phenol removal process, a second column containing degrading microorganisms was added to the last column in this research. Phenol-degrading bacteria were isolated from different microbial sources on a phenolic base medium. Additionally, encapsulated calcium peroxide nanoparticles were used to provide dissolved oxygen for the microbial population. Results showed that the both isolated strains, WC1 and CC1, were able to completely remove phenol from the contaminated influent water the range within 5 to 7 days, respectively. Molecular identification showed 99.8% similarity for WC1 isolate to Stenotrophomonas rizophila strain e-p10 and 99.9% similarity for CC1 isolate to Bacillus cereus strain IAM 12,605. The results also indicated that columns using activated sludge as a microbial source had the highest removal rate, with the microbial biofilm completely removing 100% of the 100 mg/L phenol concentration in contaminated influent water after 40 days. Finally, the concurrent use of core-shell microcapsules containing enzymes and capsules containing Stenotrophomonas sp. WC1 strain in two continuous column reactors was able to completely remove phenol from polluted water with a concentration of 500 mg/L for a period of 20 days. The results suggest that a combination of enzymatic and microbial degrading systems can be used as a new system to remove phenol from polluted streams with higher concentrations of phenol by eliminating the shock of phenol on the microbial population.

Synthesis and Characterization of Cross-Linked Aggregates of Peroxidase from Megathyrsus maximus (Guinea Grass) and Their Application for Indigo Carmine Decolorization

We present the synthesis of a cross-linking enzyme aggregate (CLEAS) of a peroxidase from Megathyrsus maximus (Guinea Grass) (GGP). The biocatalyst was produced using 50%v/v ethanol and 0.88%w/v glutaraldehyde for 1 h under stirring. The immobilization yield was 93.74% and the specific activity was 36.75 U mg-1. The biocatalyst surpassed by 61% the free enzyme activity at the optimal pH value (pH 6 for both preparations), becoming this increase in activity almost 10-fold at pH 9. GGP-CLEAS exhibited a higher thermal stability (2-4 folds) and was more stable towards hydrogen peroxide than the free enzyme (2-3 folds). GGP-CLEAS removes over 80% of 0.05 mM indigo carmine at pH 5, in the presence of 0.55 mM H2O2 after 60 min of reaction, a much higher value than when using the free enzyme. The operational stability showed a decrease of enzyme activity (over 60% in 4 cycles), very likely related to suicide inhibition.

Adsorptive removal of organic pollutants from aqueous solutions using novel GO/bentonite/MgFeAl-LTH nanocomposite

The contamination of water with organic pollutants such as dyes and phenols is a serious environmental problem, requiring effective treatment methods. In the present study, a novel nanocomposite was synthesized by intercalating graphene oxide and bentonite clay into MgFeAl-layered triple hydroxide (GO/BENT/LTH), which was characterized using different techniques. The adsorption efficacy of the GO/BENT/LTH nanocomposite was assessed via the removal of two harmful organic water pollutants, namely methyl orange (MO) and 2-nitrophenol (2NP). The obtained results revealed that the maximum adsorption capacities (qmax) of MO and 2NP reached 3106.3 and 2063.5 mg/g, respectively, demonstrating the excellent adsorption performance of the nanocomposite. Furthermore, this study examined the effects of contact time, initial MO and 2NP concentrations, pH, and temperature of the wastewater samples on the adsorptive removal of MO and 2NP by the GO/BENT/LTH nanocomposite. The pH, zeta potential, and FTIR investigations suggested the presence of more than one adsorption mechanism. Thermodynamic investigations elucidated the exothermic nature of the adsorption of MO and 2NP onto the GO/BENT/LTH nanocomposite, with MO adsorption being more sensitive to temperature change. Additionally, regeneration studies revealed a marginal loss in the MO and 2NP removal with the repetitive use of the GO/BENT/LTH nanocomposite, demonstrating its reusability. Overall, the findings of this study reveal the promise of the GO/BENT/LTH nanocomposite for effective water decontamination.

Nitrogen-Doped Biochar for Enhanced Peroxymonosulfate Activation to Degrade Phenol through Both Free Radical and Direct Oxidation Based on Electron Transfer Pathways

Nowadays, super nitrogen-doped biochar (SNBC) material has become one of the most promising metal-free catalysts for activating peroxymonosulfate (PMS) to degrade organic pollutants. To understand the evolution of SNBC properties with fabrication conditions, a variety of SNBC materials were prepared and characterized by elemental analysis, N2 adsorption-desorption, scanning electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, X-ray photoelectron spectroscopy, and X-ray diffraction. We systematically investigated the activation potential of these SNBC materials for PMS to degrade phenol. SN1BC-800 with the best catalytic performance was obtained by changing the activation temperatures and the ratio of biochar to melamine. The effects of catalyst dosage, the PMS concentration, pH, and reaction temperature on phenol degradation were studied in detail. In the presence of 0.3 g/L SN1BC-800 and 1 g/L PMS, the removal rate of 20 mg/L phenol could reach 100% within 5 min. According to electron paramagnetic resonance spectra and free radical quenching experiments, a nonfree radical pathway of phenol degradation dominated by 1O2 and electron transfer was proposed. More interestingly, the excellent catalytic performance of the SN1BC-800/PMS system is universally applicable in the degradation of other typical organic pollutants. In addition, the degradation rate of phenol is still over 80% after five reuses, which shows that the SN1BC-800 catalyst has high stability and good application prospects in environmental remediation.

Bifunctional Electrocatalysts for Overall and Hybrid Water Splitting

Electrocatalytic water splitting driven by renewable electricity has been recognized as a promising approach for green hydrogen production. Different from conventional strategies in developing electrocatalysts for the two half-reactions of water splitting (e.g., the hydrogen and oxygen evolution reactions, HER and OER) separately, there has been a growing interest in designing and developing bifunctional electrocatalysts, which are able to catalyze both the HER and OER. In addition, considering the high overpotentials required for OER while limited value of the produced oxygen, there is another rapidly growing interest in exploring alternative oxidation reactions to replace OER for hybrid water splitting toward energy-efficient hydrogen generation. This Review begins with an introduction on the fundamental aspects of water splitting, followed by a thorough discussion on various physicochemical characterization techniques that are frequently employed in probing the active sites, with an emphasis on the reconstruction of bifunctional electrocatalysts during redox electrolysis. The design, synthesis, and performance of diverse bifunctional electrocatalysts based on noble metals, nonprecious metals, and metal-free nanocarbons, for overall water splitting in acidic and alkaline electrolytes, are thoroughly summarized and compared. Next, their application toward hybrid water splitting is also presented, wherein the alternative anodic reactions include sacrificing agents oxidation, pollutants oxidative degradation, and organics oxidative upgrading. Finally, a concise statement on the current challenges and future opportunities of bifunctional electrocatalysts for both overall and hybrid water splitting is presented in the hope of guiding future endeavors in the quest for energy-efficient and sustainable green hydrogen production.

Applications of hollow nanostructures in water treatment considering organic, inorganic, and bacterial pollutants

One of the major issues of modern society is water contamination with different organic, inorganic, and contaminants bacteria. Finding cost-effective and efficient materials and methods for water treatment and environment remediation is among the scientists' most important considerations. Hollow-structured nanomaterials, including hollow fiber membranes, hollow spheres, hollow nanoboxes, etc., have shown an exciting capability for wastewater refinement approaches, including membrane technology, adsorption, and photocatalytic procedure due to their extremely high specific surface area, high porosity, unique morphology, and low density. Diverse hollow nanostructures could potentially eliminate organic contaminants, including dyes, antibiotics, oil/water emulsions, pesticides, and other phenolic compounds, inorganic pollutants, such as heavy metal ions, salts, phosphate, bromate, and other ions, and bacteria contaminations. Here, a comprehensive overview of hollow nanostructures' fabrication and modification, water contaminant classification, and recent studies in the water treatment field using hollow-structured nanomaterials with a comparative attitude have been provided, indicating the privilege abd detriments of this class of nanomaterials. Eventually, the future outlook of employing hollow nanomaterials in water refinery systems and the upcoming challenges arising in scaling up are also propounded.

Wastewater Treatment Using Membrane Bioreactor Technologies: Removal of Phenolic Contaminants from Oil and Coal Refineries and Pharmaceutical Industries

Huge amounts of noxious chemicals from coal and petrochemical refineries and pharmaceutical industries are released into water bodies. These chemicals are highly toxic and cause adverse effects on both aquatic and terrestrial life. The removal of hazardous contaminants from industrial effluents is expensive and environmentally driven. The majority of the technologies applied nowadays for the removal of phenols and other contaminants are based on physio-chemical processes such as solvent extraction, chemical precipitation, and adsorption. The removal efficiency of toxic chemicals, especially phenols, is low with these technologies when the concentrations are very low. Furthermore, the major drawbacks of these technologies are the high operation costs and inadequate selectivity. To overcome these limitations, researchers are applying biological and membrane technologies together, which are gaining more attention because of their ease of use, high selectivity, and effectiveness. In the present review, the microbial degradation of phenolics in combination with intensified membrane bioreactors (MBRs) has been discussed. Important factors, including the origin and mode of phenols' biodegradation as well as the characteristics of the membrane bioreactors for the optimal removal of phenolic contaminants from industrial effluents are considered. The modifications of MBRs for the removal of phenols from various wastewater sources have also been addressed in this review article. The economic analysis on the cost and benefits of MBR technology compared with conventional wastewater treatments is discussed extensively.

Ensemble meta machine learning for predicting the adsorption of anionic and cationic dyes from aqueous solutions using Polymer/graphene/clay/MgFeAl-LTH nanocomposite

Adsorption is one of the most promising wastewater treatment methods due to its simplicity and efficacy at ambient temperature and pressure. However, the technical and economic feasibility of this process largely depends on the performance of the utilized adsorbents. In this study, a promising adsorbent made of polyethyleneimine, graphene oxide (GO), bentonite, and MgFeAl-layered triple hydroxide (MgFeAl-LTH) has been synthesized and characterized. The results revealed that the synthesized nanocomposite (abbreviated as PGB-LTH) possesses good porosity and crystallinity. The adsorption performance of the PGB-LTH nanocomposite towards two harmful water pollutants (i.e., methyl orange (MO) and crystal violet (CV)) was investigated, and the results revealed that the nanocomposite outperforms its parental materials (i.e., GO, bentonite, and MgFeAl-LTH). The maximum adsorption capacity (qmax) of MO and CV onto the nanocomposite could reach 1666.7 and 1250.0 mg/g, respectively, as predicted using the Langmuir adsorption isotherm. Additionally, the PGB-LTH nanocomposite is highly reusable with an insignificant decline in performance upon repetitive use. In terms of thermodynamics, MO adsorption onto the nanocomposite is exothermic while CV adsorption is endothermic despite that both dyes adsorb spontaneously as revealed by the negative values of the Gibbs free energy change at all the examined temperatures. The generated adsorption data were utilized for constructing and assessing ensemble meta-machine learning techniques aimed at cost-effective simulation and prediction of the proposed adsorption method. Bagging and boosting methods were developed and evaluated intensively using the obtained adsorption data. The Extra Trees model achieved promising results as evidenced by the high correlation coefficient of 99% as well as low computed RMSE and MAE errors of 11.42 and 5.11, respectively, during the testing phase. These results demonstrate the model strong capability to effectively simulate and predict the adsorption process in question.

Phenolic compounds occurrence and human health risk assessment in potable and treated waters in Western Cape, South Africa

Phenolic pollutants from industrial and agricultural activities pose a major threat to the world's potable water supply. The persistent micro-pollutants often find their way into drinking water sources with possible adverse human health implications. In this study, bottled water, tap water, and wastewater treatment plant (WWTP) effluent samples from the Boland region of the Western Cape, South Africa were assessed to determine 4-chlorophenol (4-CP) and 2,4-dichlorophenol (2,4-DCP) levels using HPLC/DAD instrumentation. The selected area is known for its vast agricultural ventures and wineries. Evaluation of the human health risk (cancer risk) for the pollutants was conducted using the hazard quotient (HQ). The Ames mutagenicity test was also conducted using the Salmonella typhimurium T98 and T100 strains and the S9 activation enzyme. Trace levels of the phenolics were detected in the samples with a range of 9.32 × 10-7-1.15 × 10-4 mg/L obtained for 4-CP, and 8.80 × 10-7-1.72 × 10-4 mg/L recorded for 2,4-DCP. Both compounds had levels below the limit of 0.01 mg/L prescribed by South African legislation. The assessed HQ for the phenolic concentrations indicates a low level of potential ecological risk and none of the samples had a cancer risk value that exceeded the regulatory limit. The possibility of the analyzed samples causing cancer is unlikely, but non-carcinogenic adverse effects were found. Strong mutagenicity was observed for the T98 strains with a potential ability to cause mutation toward the insertion or deletion of a nucleotide. The T100 bacterial strain showed very slight mutagenicity potential, however, it is unlikely to cause any mutation. The levels of phenolics in the potable water samples may pose a significant threat to human health. Hence, screening persistent organic chemicals in potable water sources and evaluating their potential human health effects is pertinent to prevent associated health challenges.

Combining computational tools and experimental studies towards endocrine disruptors mitigation: A review of biocatalytic and adsorptive processes

The endocrine disruptors (EDCs) are an important group of emerging contaminants, and their mitigation has been a huge challenge due to their chemistry complexity and variety of these compounds. The traditional treatments are inefficient to completely remove EDCs, and adsorptive processes are the major alternative investigated on their removal. Also, the use of EDCs degrading enzymes has been encouraged due to ecofriendly approach of biocatalytic processes. This paper highlights the occurrence, classification, and toxicity of EDCs with special focus in the use of enzyme-based and adsorptive technologies in the elimination of EDCs from ambiental matrices. Numerous prior reviews have focused on the discussions toward these technologies. However, the literature lacks theoretical discussions about important aspects of these methods such as the mechanisms of EDCs adsorption on the adsorbent surface or the interactions between degrading enzymes - EDCs. In this sense, theoretical calculations combined to experimental studies may help in the development of more efficient technologies to EDCs mitigation. In this review, we point out how computational tools such as molecular docking and molecular dynamics have to contribute to the design of new adsorbents and efficient catalytic processes towards endocrine disruptors mitigation.

Coupling the recovery of spent lithium-ion batteries and the treatment of phenol wastewater: A "treating waste with waste" strategy

The recovery of spent lithium-ion batteries and the treatment of phenol wastewater are both environmental and social issues. In this study, the enhanced recovery of spent lithium-ion batteries and the efficient treatment of phenol wastewater are smartly coupled via a "treating waste with waste" strategy. Under optimal conditions, the leaching process involving phenol achieves 98% and 96% efficiency for Co and Li, respectively. After precipitation, Co and Li could be recovered as Co(OH)2 and Li2CO3, and the precipitated Co(OH)2 was further calcined to generate Co3O4. Furthermore, the organic contaminants that remained in the waste-leaching solution could be removed by a spent graphite-activating peroxymonosulfate (PMS) process. It is noteworthy that the total organic carbon (TOC) in the waste-leaching solution could be removed using fewer PMS compared with the original phenol wastewater owing to the pre-oxidation of phenol during the leaching process, further confirming the advantage of this "treating waste with waste" strategy.

An Up-to-Date Review on the Remediation of Dyes and Phenolic Compounds from Wastewaters Using Enzymes Immobilized on Emerging and Nanostructured Materials: Promises and Challenges

Addressing the critical issue of water pollution, this review article emphasizes the need to remove hazardous dyes and phenolic compounds from wastewater. These pollutants pose severe risks due to their toxic, mutagenic, and carcinogenic properties. The study explores various techniques for the remediation of organic contaminants from wastewater, including an enzymatic approach. A significant challenge in enzymatic wastewater treatment is the loss of enzyme activity and difficulty in recovery post-treatment. To mitigate these issues, this review examines the strategy of immobilizing enzymes on newly developed nanostructured materials like graphene, carbon nanotubes (CNTs), and metal-organic frameworks (MOFs). These materials offer high surface areas, excellent porosity, and ample anchoring sites for effective enzyme immobilization. The review evaluates recent research on enzyme immobilization on these supports and their applications in biocatalytic nanoparticles. It also analyzes the impact of operational factors (e.g., time, pH, and temperature) on dye and phenolic compound removal from wastewater using these enzymes. Despite promising outcomes, this review acknowledges the challenges for large-scale implementation and offers recommendations for future research to tackle these obstacles. This review concludes by suggesting that enzyme immobilization on these emerging materials could present a sustainable, environmentally friendly solution to the escalating water pollution crisis.

A hypothetical model of multi-layered cost-effective wastewater treatment plant integrating microbial fuel cell and nanofiltration technology: A comprehensive review on wastewater treatment and sustainable remediation

Wastewater management has emerged as an uprising concern that demands immediate attention from environmentalists worldwide. Indiscriminate and irrational release of industrial and poultry wastes, sewage, pharmaceuticals, mining, pesticides, fertilizers, dyes and radioactive wastes, contribute immensely to water pollution. This has led to the aggravation of critical health concerns as evident from the uprising trends of antimicrobial resistance, and the presence of xenobiotics and pollutant traces in humans and animals due to the process of biomagnification. Therefore, the development of reliable, affordable and sustainable technologies for the supply of fresh water is the need of the hour. Conventional wastewater treatment often involves physical, chemical, and biological processes to remove solids from the effluent, including colloids, organic matter, nutrients, and soluble pollutants (metals, organics). Synthetic biology has been explored in recent years, incorporating both biological and engineering concepts to refine existing wastewater treatment technologies. In addition to outlining the benefits and drawbacks of the current technologies, this review addresses novel wastewater treatment techniques, especially those using dedicated rational design and engineering of organisms and their constituent parts. Furthermore, the review hypothesizes designing a multi-bedded wastewater treatment plant that is highly cost-efficient, sustainable and requires easy installation and handling. The novel setup envisages removing all the major wastewater pollutants, providing water fit for household, irrigation and storage purposes.

Enzymatic post-treatment of ozonation: laccase-mediated removal of the by-products of acetaminophen ozonation

Ozonation is a powerful technique to remove micropollutants from wastewater. As chemical oxidation of wastewater comes with the formation of varying, possibly persistent and toxic by-products, post-treatment of the ozonated effluent is routinely suggested. This study explored an enzymatic treatment of ozonation products using the laccase from Trametes versicolor. A high-performance liquid chromatography coupled with high-resolution mass spectrometry (HPLC-HRMS) analysis revealed that the major by-products were effectively degraded by the enzymatic post-treatment. The enzymatic removal of the by-products reduced the ecotoxicity of the ozonation effluent, as monitored by the inhibition of Aliivibrio fischeri. The ecotoxicity was more effectively reduced by enzymatic post-oxidation at pH 7 than at the activity maximum of the laccase at pH 5. A mechanistic HPLC-HRMS and UV/Vis spectroscopic analysis revealed that acidic conditions favored rapid conversion of the phenolic by-products to dead-end products in the absence of nucleophiles. In contrast, the polymerization to harmless insoluble polymers was favored at neutral conditions. Hence, coupling ozonation with laccase-catalyzed post-oxidation at neutral conditions, which are present in wastewater effluents, is suggested as a new resource-efficient method to remove persistent micropollutants while excluding the emission of potentially harmful by-products.

Different crystallographic Ni(OH)2 as highly efficient Fenton-like catalysts for sulfate radical activation

By a simple hydrothermal method, a phase boundary between α- and β-Ni(OH)₂ can be obtained. The Fenton-like performance of α@β-Ni(OH)₂ is 1.56 times higher than that of single β-Ni(OH). α@β-Ni(OH)₂ displays superior stability compared to α-Ni(OH)₂, β-Ni(OH)₂, and amorphous Ni(OH)₂, which makes significant contributions to developing advanced catalysts in diverse fields.

Mesoporous carbon material prepared from sewage sludge hydrochar using Pluronic F127 as template for efficient removal of phenolic compounds: Experimental study and mechanism interpretation via advanced statistical physics model

Mesoporous carbon material (MCM) with rich ether surface group was prepared from sewage sludge hydrochar using Pluronic F127 as template under pyrolysis activation, which provided an energy-efficient method to promote the resource utilization of sewage sludge as adsorbents for phenols removal from water. The MCM possessed high surface area (549 m²/g), abundant mesopores (average width 3.81 nm) and well-developed graphite structure. Acidic conditions and low temperatures favored the adsorption of phenolic compounds. The quick adsorption process of reaching over 85% of the capacity in the first 10 min and intraparticle diffusion as primary rate-limiting step were observed for all phenolic compounds. Advanced statistical physics analysis was used successfully to interpret the adsorption mechanism of phenols onto MCM and revealed a multi-molecular monolayer adsorption process primarily through negative charge-assisted hydrogen bond interaction where the ether functional group contributed to the predominant active sites. The adsorption capacity of phenolic compounds depended upon the number of molecules adsorbed per ether active site and the available density of ether bond group on the surface of MCM. 2,4,6-trichlorophenol showed a highest adsorption priority to occupy the limited ether active sites and its adsorption capacity reached 0.49 mmol/g, while p-nitrophenol exhibited a maximum number of molecules adsorbed on the single ether active site, showing an adsorption capacity of 0.42 mmol/g. The synergistic effect of multi-interactions mechanisms resulted in phenolic compounds removal with adsorption energies lower than 30 kJ/mol. This prepared MCM adsorbent is promising for application in treatment of water polluted by phenols.

Purification and biochemical characterization of two laccase isoenzymes isolated from Trichoderma harzianum S7113 and its application for bisphenol A degradation

Two laccase isoenzymes (LacA and LacB) were isolated from a novel Trichoderma harzianum S7113 isolate employing ammonium sulfate precipitation, Sephadex G100, and DEAE Sepharose ion exchange chromatography. The molecular weights of the purified LacA and LacB laccases were estimated to be 63 and 48 kDa, respectively. The two isoenzymes had their optimum activities at the same temperature (50 °C), but at slightly different pH values (pH 3.0 for LacA and pH 2.5 for LacB). LacA and LacB had the same thermal stability at 40 °C and pH stability at pH 9.0. The two isoenzymes also showed a high level of specific activity toward ABTS, where the K_m values of LacA and LacB were 0.100 and 0.065 mM, whereas their V_max values were 0.603 and 0.182 µmol min^-1, respectively. LacA and LacB catalytic activity was stimulated by Mg²⁺, Zn²⁺, K⁺, and Ni²⁺, whereas it was inhibited by Hg²⁺ and Pb²⁺, β-mercaptoethanol, EDTA, and SDS, and completely inhibited by sodium azide. Our findings indicate that purified laccase has a promising capacity for bisphenol A (BPA) bioremediation across a broad pH range. This finding opens up new opportunities for the commercialization of this technique in a variety of biotechnology-based applications, particularly for removing endocrine chemicals from the environment.

Zeolitic imidazolate frameworks as effective crystalline supports for aspergillus-based laccase immobilization for the biocatalytic degradation of carbamazepine

In this study, zeolitic imidazolate frameworks (ZIF) were employed as effective porous supports for laccase enzyme attachment and further explored synergistic adsorption and biocatalytic degradation of carbamazepine (CBZ) in aqueous solutions. Characterization results from FTIR and NMR analysis confirmed successful incorporation of the laccase enzyme onto ZIF particles. Further analyses from SEM and TEM revealed rhombic dodecahedral morphologies of ZIF crystals with crusts of the enzyme observed on the particles' surface. The carbamazepine degradation results showed that immobilization of the laccase improved its stability and resistance at various pH's, in comparison to the free enzyme. The immobilized laccase also exhibited relatively higher activities across the studied temperature range compared to the free form. Kinetic studies revealed a negligible decline in velocity, Vmax after immobilization, evaluated to be 0.873 and 0.692 mg L-1 h-1 for the free and immobilized laccase, respectively. The immobilized laccase demonstrated improved stabilities towards organic solvents, which qualifies the composite's application in real wastewater samples. In which case, the laccase-ZIF composite proved effective in CBZ decontamination with an efficiency of ∼92%. Furthermore, the immobilized laccase exhibited appreciable storage stabilities (∼70% residual activity) for up to 15 days before any significant loss in activity.

Colourimetric Plate Assays Based on Functionalized Gelatine Hydrogel Useful for Various Screening Purposes in Enzymology

Hydrogels are intensively investigated biomaterials due to their useful physicochemical and biological properties in bioengineering. In particular, naturally occurring hydrogels are being deployed as carriers for bio-compounds. We used two approaches to develop a plate colourimetric test by immobilising (1) ABTS or (2) laccase from Trametes versicolor in the gelatine-based hydrogel. The first system (1) was applied to detect laccase in aqueous samples. We investigated the detection level of the enzyme between 0.05 and 100 µg/mL and pH ranging between 3 and 9; the stability of ABTS in the solution and the immobilised form, as well as the retention functional property of the hydrogel in 4 °C for 30 days. The test can detect laccase within 20 min in the concentration range of 2.5−100 µg/mL; is effective at pH 3−6; preserves high stability and functionality under storage and can be also successfully applied for testing samples from a microbial culture. The second system with the immobilised laccase (2) was tested in terms of substrate specificity (ABTS, syringaldazine, guaiacol) and inhibitor (NaN3) screening. ABTS appeared the most proper substrate for laccase with detection sensitivity CABTS > 0.5 mg/mL. The NaN3 tested in the range of 0.5−100 µg/mL showed a distinct inhibition effect in 20 min for 0.5 µg/mL and total inhibition for ≥75 µg/mL.

Inhibition mechanisms of Fe2+/Fe3+ and Mn2+ on fungal laccase-enabled bisphenol a polyreaction

Bisphenol A (BPA) is regarded as an endocrine disruptor associated with negative health effects in animals and humans. Laccase from white-rot fungus can enable BPA oxidation and auto-polymerization to circumvent its biotoxicity, but the work concerning the effect mechanisms of divalent and trivalent metal ions (MIs) on BPA polyreaction have rarely been reported. Herein, Trametes versicolor laccase-started BPA conversion within 1 h followed pseudo-first order kinetics, and the rate constant (k_prcs) and half-life were respectively 0.61 h^-1 and 1.14 h. The presence of Ca²⁺, Mg²⁺, Cu²⁺, Pb²⁺, Cd²⁺, Zn²⁺ and Al³⁺ exhibited insignificant impact on BPA removal, whereas Fe²⁺, Fe³⁺ and Mn²⁺ had a strong inhibiting effect. Compared with MI-free, the k_prcs values of BPA respectively lowered 34.4%, 44.3% and 98.4% in the presence of Fe²⁺, Fe³⁺ and Mn²⁺. Enzymatic activity and differential absorption spectrum disclosed that the inhibitory actions were accomplished by two different mechanisms. One is Fe²⁺ was preferentially oxidized into Fe³⁺ that restrained laccase activity at the initial stage of reaction, and subsequently, the formed Fe³⁺ complex bound with laccase T1-Cu site and thus impeded the single-electron transfer system. The other is Mn²⁺ was instantly oxidized by laccase to generate Mn³⁺-citrate complex, which completely consumed the dissolved O₂ in solution and consequently terminated BPA removal. Considering environmental bioremediation, T. versicolor laccase-enabled auto-polymerization is a simple and convenient candidate to eliminate BPA in enzymatic wastewater treatment, however the effects of Fe²⁺/Fe³⁺ and Mn²⁺ on BPA decontamination should be cautiously assessed.

Biodegradation modeling of phenol using Curtobacterium flaccumfaciens as plant-growth-promoting bacteria

Phenol is a major worry pollutant resulting from industrialized manufacturing and chemical reactions. The growth kinetics and biodegradation of phenol were initially investigated using C. flaccumfaciens, a recently identified plant growth stimulating bacterium. Based on the Haldane inhibition model, Haldane's growth kinetics inhibition coefficient (Ki), half-saturation coefficient (Ks), and the maximum specific growth rate (max) for phenol-dependent growth kinetics were estimated to be 329 (mg/L), 9.14 (mg/L), and 1.05 (h-1), respectively. With a sum of squared error (SSR) of 1.36 × 10-3, the Haldane equation is well adapted to empirical data. The improved Gombertz model also accurately predicts phenol biodegradation trends. The rate of phenol biodegradation and the lag time both increased as the initial phenol concentrations were increased. C. flaccumfaciens growth and phenol biodegradation were best achieved at a pH of 7.0 at a temperature of 28 °C incubation. A phenol biodegradation mechanism by C. flaccumfaciens has been proposed. In conclusion, this study revealed the ability of C. flaccumfaciens to promote plant growth and biodegrade phenol simultaneously. This could aid in rhizoremediation and crop yield preservation in phenol-stressed conditions.

Advances in the application of immobilized enzyme for the remediation of hazardous pollutant: A review

Nowadays, ecofriendly, low-cost, and sustainable alternatives techniques have been focused on the effective removal of hazardous pollutants from the water streams. In this context, enzyme immobilization seems to be of specific interest to several researchers to develop novel, effective, greener, and hybrid strategies for the removal of toxic contaminants. Immobilization is a biotechnological tool, anchoring the enzymes on support material to enhance the stability and retain the structural conformation of enzymes for catalysis. Recyclability and reusability are the main merits of immobilized enzymes over free enzymes. Studies showed that immobilized enzyme laccase can be used up to 7 cycles with 66% efficiency, peroxidase can be recycled to 2 cycles with 50% efficiency, and also cellulase to 3 cycles with 91% efficiency. In this review, basic concepts of immobilization, different immobilization techniques, and carriers used for immobilization are summarized. In addition to that, the potential of immobilized enzymes as the bioremediation agents for the effective degradation of pollutants from the contaminated zone and the impact of different operating parameters are summarized in-depth. Further, this review provides future trends and challenges that have to be solved shortly for enhancing the potential of immobilized systems for large-scale industrial wastewater treatment.

Solar heterogeneous photocatalytic degradation of phenol on TiO2/quartz and TiO2/calcite: a statistical and kinetic approach on comparative efficiencies towards a TiO2/glass system

Phenol is a widely used synthetic organic compound, which according to global estimations, is discharged into the environment at a rate of 10 tons/year through industrial waste. Phenol is a recalcitrant pollutant, and human exposure to water containing phenolic substances can lead to health issues. It has been found both in drinking water and wastewater. Solar heterogeneous photocatalytic phenol degradation, measured through chemical oxygen demand, was performed on a thin film tilted plate reactor with TiO₂ immobilized onto different support materials. A full factorial experimental design (4 × 3 × 3) was carried out to statistically evaluate if the independent variables' effects were significant. Four advanced oxidation processes (photolysis, photolysis + H₂O₂, heterogeneous photocatalysis, and heterogeneous photocatalysis + H₂O₂), three support materials (quartz, calcite, and glass), and three pH levels (3, 5.4, and 9) were evaluated. Reaction kinetics were fitted to the pseudo-first-order reaction rate and data was analyzed with an ANCOVA and means test, considering solar light intensity as a covariate. Photolysis/calcite at pH 5.4 and heterogeneous photocatalysis + H₂O₂/glass plate at pH 3 gave the best results, with a reaction rate constant k_ph = 3.047 × 10^-3 min^-1 and k_phC = 4.498 × 10^-3 min^-1, respectively. The three independent variables and their interactions had a significant effect in the phenol degradation (p < 0.05).

Equilibrium Studies of Iron (III) Complexes with Either Pyrazine, Quinoxaline, or Phenazine and Their Catecholase Activity in Methanol

Currently, catalysts with oxidative activity are required to create valuable chemical, agrochemical, and pharmaceutical products. The catechol oxidase activity is a model reaction that can reveal new oxidative catalysts. The use of complexes as catalysts using iron (III) and structurally simple ligands such as pyrazine (pz), quinoxaline (qx), and phenazine (fz) has not been fully explored. To characterize the composition of the solution and identify the abundant species which were used to catalyze the catechol oxidation, the distribution diagrams of these species were obtained by an equilibrium study using a modified Job method in the HypSpec software. This allows to obtain also the UV-vis spectra calculated and the formation constants for the mononuclear and binuclear complexes with Fe³⁺ including: [Fe(pz)]³⁺, [Fe₂(pz)]⁶⁺, [Fe(qx)]³⁺, [Fe₂(qx)]⁶⁺, [Fe(fz)]³⁺, and [Fe₂(fz)]⁶⁺. The formation constants obtained were log β₁₁₀ = 3.2 ± 0.1, log β₂₁₀ = 6.9 ± 0.1, log β₁₁₀ = 4.4 ± 0.1, log β₂₁₀ = 8.3 ± 0.1, log β₁₁₀ = 6.4 ± 0.2, and log β₂₁₀ = 9.9 ± 0.2, respectively. The determination of the catechol oxidase activity for these complexes did not follow a traditional Michaelis–Menten behavior.

Characteristics and pH-Responsiveness of SDBS–Stabilized Crude Oil/Water Nanoemulsions

Nanoemulsions are colloidal systems with a wide spectrum of applications in several industrial fields. In this study, crude oil-in-water (O/W) nanoemulsions were formulated using different dosages of the anionic sodium dodecylbenzenesulfonate (SDBS) surfactant. The formulated nanoemulsions were characterized in terms of emulsion droplet size, zeta potential, and interfacial tension (IFT). Additionally, the rheological behavior, long-term stability, and on-demand breakdown of the nanoemulsions via a pH-responsive mechanism were evaluated. The obtained results revealed the formation of as low as 63.5 nm average droplet size with a narrow distribution (33–142 nm). Additionally, highly negative zeta potential (i.e., −62.2 mV) and reasonably low IFT (0.45 mN/m) were obtained at 4% SDBS. The flow-ability of the nanoemulsions was also investigated and the obtained results revealed an increase in the nanoemulsion viscosity with increasing the emulsifier content. Nonetheless, even at the highest SDBS dosage of 4%, the nanoemulsion viscosity at ambient conditions never exceeded 2.5 mPa·s. A significant reduction in viscosity was obtained with increasing the nanoemulsion temperature. The formulated nanoemulsions displayed extreme stability with no demulsification signs irrespective of the emulsifier dosage even after one-month shelf-life. Another interesting and, yet, surprising observation reported herein is the pH-induced demulsification despite SDBS not possessing a pH-responsive character. This behavior enabled the on-demand breakdown of the nanoemulsions by simply altering their pH via the addition of HCl or NaOH; a complete and quick oil separation can be achieved using this simple and cheap demulsification method. The obtained results reveal the potential utilization of the formulated nanoemulsions in oilfield-related applications such as enhanced oil recovery (EOR), well stimulation and remediation, well-bore cleaning, and formation fracturing.

Co-metabolic biodegradation of 4-bromophenol in a mixture of pollutants system by Arthrobacter chlorophenolicus A6

Brominated phenols are listed as priority pollutants together with nitrophenol and chlorophenol are the key components of paper pulp wastewater. However, the biodegradation of bromophenol in a mixed substrate system is very scanty. In the present investigation, simultaneous biodegradation kinetics of three substituted phenols 4-bromophenol (4-BP), 4-nitrophenol (4-NP), and 4-chlorophenol (4-CP) were investigated using Arthrobacter chlorophenolicus A6. A 2³ full factorial design was applied with varying 4-BP and 4-CP from 75-125 mg/L and 4-NP from 50-100 mg/L. Almost complete degradation of this mixture of substituted phenols was achieved at initial concentration combinations of 125, 125, and 100 mg/L of 4-CP, 4-BP, and 4-NP, respectively, in 68 h. Statistical analysis of the results revealed that, among the three variables, 4-NP had the most prominent influence on the degradation of both 4-CP and 4-BP, while the concentration of 4-CP had a strong negative interaction effect on the biodegradation of 4-NP. Irrespective of the concentration levels of these three substrates, 4-NP was preferentially biodegraded over 4-CP and 4-BP. Furthermore, 4-BP biodegradation rates were found to be higher than those of 4-CP, followed by 4-NP. Besides, the variation of the biomass yield coefficient of the culture was investigated at different initial concentration combinations of these substituted phenols. Although the actinomycetes consumed 4-NP at a faster rate, the biomass yield was very poor. This revealed that the microbial cells were more stressed when grown on 4-NP compared to 4-BP and 4-CP. Overall, this study revealed the potential of A. chlorophenolicus A6 for the degradation of 4-BP in mixed substrate systems.

Colorimetric sensing strategy for detection of cysteine, phenol cysteine, and phenol based on synergistic doping of multiple heteroatoms into sponge-like Fe/NPC nanozymes

Nanozymes have both the high catalytic activity of natural enzymes and the stability and economy of mimetic enzymes. Research on nanozymes is rapidly emerging, and the continuous development of highly catalytic active nanozymes is of far-reaching significance. This work reports heteroatomic nitrogen (N) and phosphorus (P) double-doped mesoporous carbon structures and metallic Fe coordination generated sponge-like nanozymes (Fe/NPCs) with good peroxidase activity. On this basis, we constructed a highly sensitive colorimetric sensor with cysteine and phenol as simulated analytes using Fe/NPCs nanozymes, and the response limits reached 53.6 nM and 5.4 nM, respectively. Besides, the method has high accuracy in the detection of cysteine and phenol at low concentrations in serum and tap water, which lays a foundation for application in the fields of environmental protection and biosensors.

Production of Plant Proteases and New Biotechnological Applications: An Updated Review

An updated review of emerging plant proteases with potential biotechnological application is presented. Plant proteases show comparable or even greater performance than animal or microbial proteases for by-product valorization through hydrolysis for, for example, cheese whey, bird feathers, collagen, keratinous materials, gelatin, fish protein, and soy protein. Active biopeptides can be obtained as high added value products, which have shown numerous beneficial effects on human health. Plant proteases can also be used for wastewater treatment. The production of new plant proteases is encouraged for the following advantages: low cost of isolation using simple procedures, remarkable stability over a wide range of operating conditions (temperature, pH, salinity, and organic solvents), substantial affinity to a broad variety of substrates, and possibility of immobilization. Vegetable proteases have enormous application potential for the valorization of industrial waste and its conversion into products with high added value through low-cost processes.

Agricultural waste materials for adsorptive removal of phenols, chromium (VI) and cadmium (II) from wastewater: A review

Management of basic natural resources and the spent industrial and domestic streams to provide a sustainable safe environment for healthy living is a magnum challenge to scientists and environmentalists. The present remedial approach to the wastewater focuses on recovering pure water for reuse and converting the contaminants into a solid matrix for permanent land disposal. However, the ground water aquifers, over a long period slowly leach the contaminants consequently polluting the ground water. Synthetic adsorbents, mainly consisting of polymeric resins, chelating agents, etc. are efficient and have high specificity, but ultimate disposal is a challenge as most of these materials are non-biodegradable. In this context, it is felt appropriate to review the utility of adsorbents based on natural green materials such as agricultural waste and restricted to few model contaminants: phenols, and heavy metals chromium(VI), and cadmium(II) in view of the vast amount of literature available. The article discusses the features of the agricultural waste material-based adsorbents including the mechanism. It is inferred that agricultural waste materials are some of the common renewable sources available across the globe and can be used as sustainable adsorbents. A discussion on challenges for industrial scale implementation and integration with advanced technologies like magnetic-based approaches and nanotechnology to improve the removal efficiency is included for future prospects.

A smart enzyme reactor based on a photo-responsive hydrogel for purifying water from phenol contaminated sources

In this paper, a smart enzyme reactor (SER) was synthesized using immobilized tyrosinase (Tyr) in a photo-responsive hydrogel via a polydopamine-assisted self-assembly strategy for purifying water from phenol contaminated water. PDA was not only utilized as a binder between Tyr and the hydrogel to prevent the leakage of Tyr with relatively high enzymatic activity from the SER, but also acted as a light absorber to trigger the hydrophilic/hydrophobic switching of PNIPAm hydrogels to realize the efficient reclamation of clean water. Experimental results showed that the SER maintained a well-defined porous structure with excellent elasticity, which was beneficial for water transport and enzyme accessibility. And the stability and reusability of Tyr in the degradation of phenol were all improved. Furthermore, clean water could be reclaimed completely and facilely by light irradiation after enzymatic remediation in the SER.

Immobilized enzymes and cell systems: an approach to the removal of phenol and the challenges to incorporate nanoparticle-based technology

The presence of phenol in wastewater poses a risk to ecosystems and human health. The traditional processes to remove phenol from wastewater, although effective, have several drawbacks. The best alternative is the application of ecological biotechnology tools since they involve biological systems (enzymes and microorganisms) with moderate economic and environmental impact. However, these systems have a high sensitivity to environmental factors and high substrate concentrations that reduce their effectiveness in phenol removal. This can be overcome by immobilization-based technology to increase the performance of enzymes and bacteria. A key component to ensure successful immobilization is the material (polymeric matrices) used as support for the biological system. In addition, by incorporating magnetic nanoparticles into conventional immobilized systems, a low-cost process is achieved but, most importantly, the magnetically immobilized system can be recovered, recycled, and reused. In this review, we study the existing alternatives for treating wastewater with phenol, from physical and chemical to biological techniques. The latter focus on the immobilization of enzymes and microorganisms. The characteristics of the support materials that ensure the viability of the immobilization are compared. In addition, the challenges and opportunities that arise from incorporating magnetic nanoparticles in immobilized systems are addressed.

Enhanced photocatalytic degradation of toxic contaminants using Dy2O3-SiO2 ceramic nanostructured materials fabricated by a new, simple and rapid sonochemical approach

The present study is on the fabrication of new photocatalytic nanocomposites (Dy2O3-SiO2) employing a basic agent, tetraethylenepentamine (Tetrene), through a simple, efficient and, quick sonochemical approach. The features of the fabricated photocatalytic nanocomposite were examined employing a variety of microscopic and spectroscopic methods such as XRD, EDS, TEM, FTIR, DRS, and FESEM. The outcomes of morphological studies demonstrated that by proper tuning of sonication time and ultrasonic power (10 min and 400 W), a porous nanocomposite composed of sphere-shaped nanoparticles with a particle size in the range of 20 to 60 nm could be fabricated. The energy gap for the binary Dy2O3-SiO2 nanophotocatalyst was determined to be 3.41 eV, making these nanocomposite favorable for removing contaminants. The photocatalytic performance of the optimal nanocomposite sample was tested for photodecomposition of several contaminants including erythrosine, thymol blue, eriochrome black T, Acid Red 14, methyl orange, malachite green, and Rhodamine B. The binary Dy2O3-SiO2 nanophotocatalyst exhibited superior efficiency toward the decomposition of the studied contaminants. It was able to degrade the erythrosine pollutant more effectively (92.9%). Optimization studies for the photocatalytic decomposition of each contaminant demonstrated that the best performance could be achieved at a specific amount of contaminant and nanocatalyst. Trapping experiments illustrated that hydroxyl radicals were more effectively involved in the decomposition of contaminant molecules by Dy2O3-SiO2 nanophotocatalyst.

A POM-based copper-coordination polymer crystal material for phenolic compound degradation by immobilizing horseradish peroxidase

A new polyoxometalate (POM)-based organic-inorganic hybrid Cu-coordination polymer, namely {((Cu(bipy))2(μ-PhPO3)2Cu(bipy))2H(PCuW11O39)·3H2O}n (denoted as compound 1, bipy = 2,2'-bipyridine, PhPO3 = phenylphosphonate), was self-assembled hydrothermally. Single-crystal X-ray diffraction (SC-XRD) analysis shows that two unique types of 1D chains are present in compound 1, i.e. Cu(II)-organophosphine and organonitrogen complex cation ([((Cu(bipy))2(μ-PhPO3)2Cu(bipy))2]4+) chains and Cu-monosubstituted Keggin-type polyoxoanion ([PCuW11O39]5-) chains, forming a hetero-POM. Crystalline compound 1 as a new enzyme immobilization support exhibited a high horseradish peroxidase (HRP) loading capacity (268 mg g-1). The powder X-ray diffraction (PXRD), FTIR, zeta potential, confocal laser scanning microscopy (CLSM) and circular dichroism (CD) results show that HRP is only immobilized on the surface of compound 1 through simple physical adsorption without a secondary structure change. This POM-immobilized enzyme (HRP/1) was first used for degradation of pollutants in wastewater, and it showed a high degradation efficiency and TOC removal efficiency for phenol, 4-chlorophenol (4-CP) and 2,4-dichlorophenol (2,4-DCP) within 30 min reaction time. Moreover, HRP/1 exhibited better operational and storage stabilities and reusability compared with free HRP. This work suggests that POMs can be used as new supports for enzyme immobilization and POM-immobilized enzymes may be used as a new kind of biocatalyst for degradation of phenolic pollutants.

Removal of organic compounds by nanoscale zero-valent iron and its composites

During the latest several decades, the continuous development of the economy and industry has brought more and more serious organic pollutants to the natural environment, which have inevitably aroused severe menace to human health and the environmental system. The nano zero-valent iron (NZVI) particles and NZVI-based materials have widely applied to remove organic pollutants. This article reviews the key advancements of different methods for the synthesis of NZVI and NZVI-based materials. Different modification methods (e.g., doped NZVI, encapsulated NZVI and supported NZVI) are also introduced detailedly for overcoming the defects of NZVI such as aggregation and easy oxidation. The removal of different organic pollutants including dyes, halogenated organic compounds, nitro-organic compounds, phenolic compounds, pesticides, and antibiotics are summarized. The interaction mechanisms, including adsorption, reduction, and active oxidation of organic pollutants by NZVI/NZVI-based composites, are discussed. The dyes are mainly removed by destroying their chromogenic group according to the reduction or the Fenton-like reaction with NZVI. The removal of halogenated organic compounds (HOCs) is realized by the dehalogenation process, including reductive elimination, hydrogenolysis, and hydrogenation. As for the nitro-organic compounds, three different reduction pathways as nitro-reduction (into amino), cleavage at the carbon‑nitrogen bond or denitration of the NO₂ group may take effect. The phenolic compounds can be mineralized into inorganic molecules, including CO₂ and H₂O, by Fenton oxidation. This review might provide the basis for future studies on developing more effective NZVI-based materials for the treatment of wastewaters contaminated by organic pollutants.

Performance of single-stage partial nitritation and anammox reactor treating low-phenol/ammonia ratio wastewater and analysis of microbial community structure

Phenol and ammonia are common pollutants in many industrial wastewaters. The partial nitritation and anammox process is a very promising technology for treating phenol-ammonia wastewater. This study was the first time to rapidly achieve the start-up and operation of the single-stage partial nitritation /anammox reactor treating phenol-ammonia wastewater. The optimized ratio of phenol and nitrogen (phenol/NH₄ ⁺ -N=0.3) was set to start-up the reactor. After 60 days of operation, the total nitrogen and COD removal efficiencies were around 73.0% and 79.5%, respectively. The activity of ammonium-oxidizing bacteria was291.1 ± 3.0 mg NH₄ ⁺ -N g^-1 MLVSS d^-1 and the specific anammox activity was 20.9 ± 1.0 mg NH₄ ⁺ -N g^-1 MLVSS d^-1 . The results indicated that the anammox bacteria had adapted to phenol condition and remained stable activity after the 60 days' operation in the reactor. The sequence analysis of 16SrRNA showed that the microbial community structure evolved to a balanced distribution that the removals of phenol and ammonia could be achieved simultaneously. PRACTITIONER POINTS: Phenol/N ratio of 0.3 was set to start up the single-stage partial nitritation/anammox reactor. The single-stage partial nitritation /anammox reactor was rapidly started up when treating the phenol-ammonia wastewater. Total nitrogen removal rate and COD removal efficiencies could achieve to 73.0% and 79.5%, respectively. Microbial community structure evolved to stable distribution of which AOB, anammox bacteria, denitrification bacteria and heterotrophic nitrification bacteria coexisted.

Amino Acid-Based Natural Deep Eutectic Solvents for Extraction of Phenolic Compounds from Aqueous Environments

The environmental pollution of phenol-containing wastewater is an urgent problem with industrial development. Natural deep eutectic solvents provide an environmentally friendly alternation for the solvent extraction of phenol. This study synthesized a series of natural deep eutectic solvents with L-proline and decanoic acid as precursors, characterized by in situ infrared spectrometry, Fourier transform infrared spectrometry, hydrogen nuclear magnetic resonance spectrometry, and differential thermogravimetric analysis. Natural deep eutectic solvents have good thermal stability. The high-efficiency extraction of phenol from wastewater by natural deep eutectic solvents was investigated under mild conditions. The effects of natural deep eutectic solvents, phenol concentration, reaction temperature, and reaction time on phenol extraction were studied. The optimized extraction conditions of phenol with L-prolin/decanoic acid were as follows: molar ratio, 4.2:1; reaction time, 60 min; and temperature, 50 °C. Extraction efficiency was up to 62%. The number of extraction cycles can be up to 6, and extraction rate not less than 57%. The promising results demonstrate that natural deep eutectic solvents are efficient in the field of phenolic compound extraction in wastewater.

Simultaneous photocatalytic reduction of hexavalent chromium and oxidation of p-cresol over AgO decorated on fibrous silica zirconia

The co-existence of heavy metals and organic compounds including Cr(VI) and p-cresol (pC) in water environment becoming a challenge in the treatment processes. Herein, the synchronous photocatalytic reduction of Cr(VI) and oxidation of pC by silver oxide decorated on fibrous silica zirconia (AgO/FSZr) was reported. In this study, the catalysts were successfully developed using microemulsion and electrochemical techniques with various AgO loading (1, 5 and 10 wt%) and presented as 1, 5 and 10-AgO/FSZr. Catalytic activity was tested towards simultaneous photoredox of hexavalent chromium and p-cresol (Cr(VI)/pC) and was ranked as followed: 5-AgO/FSZr (96/78%) > 10-AgO/FSZr (87/61%) > 1-AgO/FSZr (47/24%) > FSZr (34/20%). The highest photocatalytic activity of 5-AgO/FSZr was established due to the strong interaction between FSZr and AgO and the lowest band gap energy, which resulted in less electron-hole recombination and further enhanced the photoredox activity. Cr(VI) ions act as a bridge between the positive charge of catalyst and cationic pC in pH 1 solution which can improve the photocatalytic reduction and oxidation of Cr(VI) and pC, respectively. The scavenger experiments further confirmed that the photogenerated electrons (e^-) act as the main species for Cr(VI) to be reduced to Cr(III) while holes (h⁺) and hydroxyl radicals are domain for photooxidation of pC. The 5-AgO/FSZr was stable after 5 cycles of reaction, suggesting its potential for removal of Cr(VI) and pC simultaneously in the chemical industries.

Roles and applications of enzymes for resistant pollutants removal in wastewater treatment

Resistant pollutants like oil, grease, pharmaceuticals, pesticides, and plastics in wastewater are difficult to be degraded by traditional activated sludge methods. These pollutants are prevalent, posing a great threat to aquatic environments and organisms since they are toxic, resistant to natural biodegradation, and create other serious problems. As a high-efficiency biocatalyst, enzymes are proposed for the treatment of these resistant pollutants. This review focused on the roles and applications of enzymes in wastewater treatment. It discusses the influence of enzyme types and their sources, enzymatic processes in resistant pollutants remediation, identification and ecotoxicity assay of enzymatic transformation products, and typically employed enzymatic wastewater treatment systems. Perspectives on the major challenges and feasible future research directions of enzyme-based wastewater treatment are also proposed.

Technology Advances in Phenol Removals: Current Progress and Future Perspectives

Phenol acts as a pollutant even at very low concentrations in water. It is classified as one of the main priority pollutants that need to be treated before being discharged into the environment. If phenolic-based compounds are discharged into the environment without any treatments, they pose serious health risks to humans, animals, and aquatic systems. This review emphasizes the development of advanced technologies for phenol removal. Several technologies have been developed to remove phenol to prevent environmental pollution, such as biological treatment, conventional technologies, and advanced technologies. Among these technologies, heterogeneous catalytic ozonation has received great attention as an effective, environmentally friendly, and sustainable process for the degradation of phenolic-based compounds, which can overcome some of the disadvantages of other technologies. Recently, zeolites have been widely used as one of the most promising catalysts in the heterogeneous catalytic ozonation process to degrade phenol and its derivatives because they provide a large specific surface area, high active site density, and excellent shape-selective properties as a catalyst. Rational design of zeolite-based catalysts with various synthesis methods and pre-defined physiochemical properties including framework, ratio of silica to alumina (SiO2/Al2O3), specific surface area, size, and porosity, must be considered to understand the reaction mechanism of phenol removal. Ultimately, recommendations for future research related to the application of catalytic ozonation technology using a zeolite-based catalyst for phenol removal are also described.