Recent advances of loose nanofiltration membranes for dye/salt separation

Purifying surface water contaminated with azo dyes using nanofiltration: Interactions between dyes and dissolved organic matter

In this research, the interactions of two azo dyes, Methyl Orange (MO) and Eriochrome Black T (EBT), with dissolved organic matter (DOM) in surface water were studied, emphasizing their removal using nano-filtration membranes (NF-270 and NF-90). High-Performance Size Exclusion Chromatography (HPSEC) findings indicated that the dyes' molecular weight in deionized (DI) water ranged from 500 to 15k Dalton (Da), adjusting peak intensities with Jingmi River (JM) water Beijing. Notably, when dyes were diluted in JM water, ultraviolet (UV533 & 466, and UV254), together with total organic carbon (TOC) parameters, revealed color removal rates of 99.49% (EBT), 94.2% (MO), 87.6% DOM removal, and 86% TOC removal for NF-90. The NF-90 membrane demonstrated a 75% flux decline for 50 mL permeate volume due to its finer pore structure and higher rejection effectiveness. In contrast, the NF-270 membrane showed a 60% decline in flux under the same conditions. Attenuated total reflection-Fourier transform infrared spectroscopy (ATR-FTIR) analysis of dye-treated membranes in JM water revealed that the NF-270 showed a CC bond peak at 1660 cm-1 across various samples, while analyzing NF-90, the peaks at 1400 cm-1, 1040 cm-1, 750 cm-1, and 620 cm-1 disappeared for composite sample removal. The hydrophobicity of each membrane is measured by the contact angle (CA), which identified that initial CAs for NF-270 and NF-90 were 460 and 700, respectively, that were rapidly declined but stabilized after a few seconds of processing. Overall, this investigation shows that azo dyes interact with DOM in surface waters and enhance the removal efficiency of NF membranes.

pH-triggered polydopamine-decorated nanocellulose membranes for continuously selective separation of organic dyes

Membrane separation technology has emerged as a powerful tool to separate organic dyes from industrial wastewater. However, continuously selective separation of organic dyes with similar molecular weight remains challenging. Herein, we presented a pH-triggered membrane composed of polydopamine-decorated tunicate-derived cellulose nanofibers (PDA@TCNFs) for selective separation of organic dyes. Such self-supporting membranes with nanoporous structure were fabricated by facile vacuum-assisted filtration of PDA@TCNF suspension. The incorporation of polydopamine not only enhanced the stability of the membranes, but also endowed membranes with excellent pH sensitivity, facilitating the continuously selective separation of organic dyes. These pH-triggered PDA@TCNF membranes could selectively separate Methyl Orange (MO) and Rhodamine B (RB) from the MO/RB mixed solution by switching the pH values. The continuously selective separation of the MO/RB mixed solution was demonstrated, where both MO and RB recovery ratios maintained at ∼99 % during 50 repeated cycles. This work provides a new strategy to develop a pH-triggered sustainable nanocellulose-based membrane for continuously selective separation of mixed dyes.

Facile fabrication of sulfonated porous yeast carbon microspheres through a hydrothermal method and their application for the removal of cationic dye

Water pollution containing dyes become increasingly serious environmental problem with the acceleration of urbanization and industrialization process. Renewable adsorbents for cationic dye wastewater treatment are becoming an obstacle because of the difficulty of desorbing the dye from the adsorbent surface after adsorption. To overcome this dilemma, herein, we report a hydrothermal method to fabricate sulfonic acid modified yeast carbon microspheres (SA/YCM). Different characterization techniques like scanning electron microscopy, FTIR spectroscopy, and X-ray diffraction have been used to test the SA/YCM. Decorated with sulfonic acid group, the modified yeast carbon microspheres possess excellent ability of adsorbing positively charged materials. The removal rate of Methyl blue (MB) by renewable adsorbent SA/YCM can reach 85.3% when the concentration is 500 mg/L. The SA/YCM regenerated by HCl showed excellent regeneration adsorption capacity (78.1%) after five cycles of adsorption-desorption regeneration experiment. Adsorption isotherm and kinetic behaviors of SA/YCM for methylene blue dyes removal were studied and fitted to different existing models. Owing to the numerous sulfonic acid groups on the surface, the SA/YCM showed prominent reusability after regeneration under acidic conditions, which could withstand repeated adsorption-desorption cycles as well as multiple practical applications.

Recent progress in defect-engineered metal oxides for photocatalytic environmental remediation

Rapid industrial advancement over the last few decades has led to an alarming increase in pollution levels in the ecosystem. Among the primary pollutants, harmful organic dyes and pharmaceutical drugs are directly released by industries into the water bodies which serves as a major cause of environmental deterioration. This warns of a severe need to find some sustainable strategies to overcome these increasing levels of water pollution and eliminate the pollutants before being exposed to the environment. Photocatalysis is a well-established strategy in the field of pollutant degradation and various metal oxides have been proven to exhibit excellent physicochemical properties which makes them a potential candidate for environmental remediation. Further, with the aim of rapid industrialization of photocatalytic pollutant degradation technology, constant efforts have been made to increase the photocatalytic activity of various metal oxides. One such strategy is the introduction of defects into the lattice of the parent catalyst through doping or vacancy which plays a major role in enhancing the catalytic activity and achieving excellent degradation rates. This review provides a comprehensive analysis of defects and their role in altering the photocatalytic activity of the material. Various defect-rich metal oxides like binary oxides, perovskite oxides, and spinel oxides have been summarized for their application in pollutant degradation. Finally, a summary of existing research, followed by the existing challenges along with the potential countermeasures has been provided to pave a path for the future studies and industrialization of this promising field.

Fenton reaction in the process of "Laser + Fe" mode excited plasma for Rhodamine B degradation

The spectral emission of laser-induced plasma in water has a broadband continuum containing ultraviolet light, which can be used as a novel light source for the degradation of organic compounds. We studied the degradation process of the organic dye Rhodamine B (RhB) using plasma light source excited by the "Laser + Fe" mode. Spectral analysis and reaction kinetics modelling were used to study the degradation mechanism. The degradation process using this light source could be divided into two stages. The initial stage was mainly photocatalytic degradation, where ultraviolet light broke the chemical bond of RhB, and then RhB was degraded by the strong oxidising ability of ·OH. As the iron and hydrogen ion concentrations increased, the synergistic effect of photocatalysis and the Fenton reaction further enhanced the degradation rate in the later stage. The plasma excited by the "Laser + Fe" mode achieved photodegradation by effectively enhancing the ultraviolet wavelength ratio of the emission spectrum and triggered the Fenton reaction to achieve rapid organic matter degradation. Our findings indicate that the participation of the Fenton reaction can increase the degradation rate by approximately 10 times. Besides, the impact of pH on degradation efficiency demonstrates that both acidic and alkaline environments have better degradation effects than neutral conditions; this is because acidic environments can enhance the Fenton reaction, while alkaline environments can provide more ·OH.

Construction of PDA-PEI/ZIF-L@PE tight ultra-filtration (TUF) membranes on porous polyethylene (PE) substrates for efficient dye/salt separation

Tight ultra-filtration (TUF) membranes were constructed by in situ growing zinc imidazole frameworks micro-crystalline leaves (ZIF-L) in polyethylene imine (PEI) and polydopamine (PDA) deposit layers on porous polyethylene (PE) substrates. The effects of preparation conditions on the surface physical and chemical structures as well as on the dye/salt separation performance of the formed TUF membranes were systematically investigated. By inserting selective water permeation channels and increasing contacting surface areas, in situ-grown ZIF-L arrays tightly cross-linked in the coating matrix greatly increased water permeation without trading off dye/salt retention selectivity. The morphology of the included ZIF-L particles could be varied by adjusting the ligand/Zn molar ratio (α) in the preparation processes. Optimized PDA-PEI/ZIF-L@PE TUF membranes containing ZIF-L of cross-cross block morphology showed very high pure water permeability of 180 ± 20 L·m-2·h-1·bar-1 (LMHB) and retention selectivity (SCR/Na2SO4 and SMB/Na2SO4) of 267 and 43, respectively, as well as excellent stability and anti-fouling properties.

Design and Machine Learning Prediction of In Situ Grown PDA-Stabilized MOF (UiO-66-NH2) Membrane for Low-Pressure Separation of Emulsified Oily Wastewater

Significant progress has been made in designing advanced membranes; however, persistent challenges remain due to their reduced permeation rates and a propensity for substantial fouling. These factors continue to pose significant barriers to the effective utilization of membranes in the separation of oil-in-water emulsions. Metal-organic frameworks (MOFs) are considered promising materials for such applications; however, they encounter three key challenges when applied to the separation of oil from water: (a) lack of water stability; (b) difficulty in producing defect-free membranes; and (c) unresolved issue of stabilizing the MOF separating layer on the ceramic membrane (CM) support. In this study, a defect-free hydrolytically stable zirconium-based MOF separating layer was formed through a two-step method: first, by in situ growth of UiO-66-NH2 MOF into the voids of polydopamine (PDA)-functionalized CM during the solvothermal process, and then by facilitating the self-assembly of UiO-66-NH2 with PDA using a pressurized dead-end assembly. A stable MOF separating layer was attained by enriching the ceramic support with amines and hydroxyl groups using PDA, which assisted in the assembly and stabilization of UiO-66-NH2. The PDA-s-UiO-66-NH2-CM membrane displayed air superhydrophilicity and underwater superoleophobicity, demonstrating its oil resistance and high antifouling behavior. The PDA-s-UiO-66-NH2-CM membrane has shown exceptionally high permeability and separation capacity for challenging oil-in-water emulsions. This is attributed to numerous nanochannels from the membrane and its high resistance to oil adhesion. The membranes showed excellent stability over 15 continuous test cycles, which indicates that the developed MOFs separating layers have a low tendency to be clogged by oil droplets during separation. Machine learning-based Gaussian process regression (GPR) models as nonparametric kernel-based probabilistic models were employed to predict the performance efficiency of the PDA-s-UiO-66-NH2-CM membrane in oil-in-water separation. The outcomes were compared with the support vector machine (SVM) and decision tree (DT) algorithm. This efficiency includes various metrics related to its separation accuracy, and the models were developed through feature engineering to identify and utilize the most significant factors affecting the membrane's performance. The results proved the reliability of GPR optimization with the highest prediction accuracy in the validation phase. The average percentage increase of the GPR model compared to the SVM and DT model was 6.11 and 42.94%, respectively.

Energy-efficient trehalose-based polyester nanofiltration membranes for zero-discharge textile wastewater treatment

Recovery of water, salts, and hazardous dye from complex saline textile wastewater faces obstacles in separating dissolved ionic substances and recovering organic components during desalination. This study realized the simultaneous fractionation, desalination, and dye removal/recovery treatment of textile wastewater by using trehalose (Tre) as an aqueous monomer to prepare polyester loose nanofiltration (LNF) membrane with fine control microstructure via interfacial polymerization. Outperforming the NF270 commercial membrane, the Tre-1.05/TMC optimized membrane achieves zero-discharge textile wastewater treatment, cutting energy consumption by 295% and reducing water consumption by 42.8%. This efficiency surge results from remarkable water permeability (130.83 L m-2 h-1 bar-1) and impressive dye desalination (NaCl/ Direct Red 23 separation factor of 275) of the Tre-1.05/TMC membrane. For a deeper comprehension of filtration performance, the sieving mechanism of polyester LNF membranes was systematically elucidated. This strategic approach offers significant prospects for energy conservation, carbon emission mitigation, and enhanced feasibility of membrane-based wastewater treatment systems.

Polyester Nanofiltration Membranes for Efficient Cations Separation

Polyester nanofiltration membranes highlight beneficial chlorine resistance, but their loose structures and negative charge result in poor cations retention precluding advanced use in cations separation. This work designs a new monomer (TET) containing "hydroxyl-ammonium" entities that confer dense structures and positive charge to polyester nanofiltration membranes. The TET monomer undergoes efficient interfacial polymerization with the trimesoyl chloride (TMC) monomer, and the resultant TET-TMC membranes feature one of the lowest molecular weight cut-offs (389 Da) and the highest zeta potential (4 mv, pH: 7) among all polyester nanofiltration membranes. The MgCl2 rejection of the TET-TMC membrane is 95.5%, significantly higher than state-of-the-art polyester nanofiltration membranes (<50%). The Li+ /Mg2+ separation performance of TET-TMC membrane is on par with cutting-edge polyamide membranes, while additionally, the membrane is stable against NaClO though polyamide membranes readily degrade. Thus the TET-TMC is the first polyester nanofiltration membrane for efficient cations separation.

Surface Bioengineering of Mo2Ga2C MAX Phase to Develop Blended Loose Nanofiltration Membranes for Textile Wastewater Treatment

The potential of blended loose nanofiltration membranes (LNMs) to fractionate dyes and inorganic salts in textile wastewater has become a focus of attention in recent years. In this research work, we fabricated LNMs based on polysulfone (PSf) membranes blended with l-histidine amino acid-functionalized Mo2Ga2C MAX phase (His-MAX). Scanning electron microscopy (SEM), atomic force microscopy (AFM), attenuated total reflectance-Fourier transform infrared spectroscopy (ATR-FTIR), contact angle, ζ-potential, porosity, and pore size analyses were employed to characterize the LNMs. Blending 0.75 wt % of His-MAX additive with the PSf tailored the LNM's features by making it more water-friendly, increasing its porosity, enlarging its pores, and making its surface smoother. The pure water flux of 127.6 L/m2 h was achieved by LNM containing 0.75 wt % His-MAX, which was 2.5 times greater than the bare one. The mentioned LNM displayed a flux recovery ratio (FRR) of 68.27 and 98.57, 98.31, and 99.7% rejections for Direct red 23, Acid brown 75, and Reactive blue 21 solutions (100 mg/L), respectively. The 0.75 wt % His-MAX LNM could reject 99.1% of dye and 11.5% of salt while maintaining an FRR of 91.19% after four cycles of filtering a binary mixture solution containing Reactive blue 21 and Na2SO4. These findings highlight the potential of the fabricated LNM for desalinating dye solutions.

Rapid and efficient removal of methylene blue dye from aqueous solutions using extract-modified Zn-Al LDH

Environmental pollution, particularly water pollution caused by organic substances like synthetic dyes, is a pressing global concern. This study focuses on enhancing the adsorption capacity of layered double hydroxides (LDHs) to remove methylene blue (MB) dye from water. The synthesized materials are characterized using techniques like FT-IR, XRD, SEM, TEM, TGA, EDS, BET, BJH, AFM, and UV-Vis DRS. Adsorption experiments show that Zn-Al LDH@ext exhibits a significant adsorption capacity for MB dye compared to pristine LDH. In addition, Zn-Al LDH@ext shows a significant increase in stability, which is attributed to the presence of phenolic compounds in the extract and the interactions between the functional groups of the extract and LDH. The pH and adsorbent dosage optimizations show that pH 7 and 0.7 g of Zn-Al LDH@ext are optimal conditions for efficient MB removal. The study assessed adsorption kinetics through the examination of Langmuir, Freundlich, and Temkin isotherms. Additionally, four kinetic models, namely pseudo-first-order, pseudo-second-order, intraparticle diffusion, and Elovich, were analyzed. The results indicated that the Temkin isotherm (R2 = 0.9927), and pseudo-second-order (R2 = 0.9999) kinetic provided the best fit to the experimental data. This study introduces a novel approach to enhance adsorption efficiency using modified LDHs, contributing to environmentally friendly and cost-effective water treatment methods.

Cation-Intercalated Clay-Based Two-Dimensional Membranes for Effective Desalination and Molecule Sieving

Montmorillonite (MMT) is known as an ion-exchangeable material, and cations between MMT nanosheets are easily exchanged by other cations. In this work, Ca2+, Fe3+, and Al3+ intercalated two-dimensional MMT membranes were developed by ion exchange of pristine MMT membranes (Na+-MMT), and their ion and dye removal abilities were investigated. The d-spacings of hydrated Fe3+ intercalated MMT membrane (Fe3+-MMT) and Al3+ intercalated MMT membrane (Al3+-MMT) were decreased compared with hydrated Na+-MMT membrane due to the stronger electrostatic attraction between Fe3+/Al3+ and negatively charged MMT nanosheets. Ion and dye sieving performances were improved significantly after the intercalation of Ca2+, Fe3+, and Al3+ into MMT membranes. Al3+-MMT membrane with a thickness of 1.17 μm could exclude 94% of Na+, and its ion sieving performance remained stable during a 120-h ion sieving experiment. Moreover, the rejection rate for rhodamine B (RB) reached 94% using an Al3+-MMT membrane with a thickness of 500 nm, and a water permeance of 73 L m-2 h-1 bar-1 was achieved. The excellent ion and dye sieving performances make it promising in the application of desalination and nanofiltration.

Ionic Hyperbranched Poly(amido-amine)-Incorporated Nanofiltration Membranes for High-Efficiency Dye Desalination

High-efficiency dye desalination is crucial in the textile industry, considering its importance for human health, safe aquatic ecological systems, and resource recovery. In order to solve the problem of effective separation of univalent salt and ionic dye under the condition of high salt, ionic hyperbranched poly(amido-amine) (HBPs) were synthesized based on a simple and scalable one-step polycondensation method and then incorporated into the polyamide (PA) selective layers to construct charged nanochannels through interfacial polymerization (IP) on the surface of a polyvinyl chloride ultrafiltration (PVC-UF) hollow fiber membrane. Both the internal nanopores of HBPs (internal nanochannels) and the interfacial voids between HBPs and the PA matrix (external nanochannels) can be regarded as a fast water molecule transport pathway, while the terminal ionic groups of ionic HBPs endow the nanochannels with charge characteristics for improving ionic dye/salt selectivities. The permeate fluxes and dye/salt selectivities of HBP-TAC/PIP (57.3 L m-2 h-1 and rhodamine B (RB)/NaCl selectivity of 224.0) and HBP-PS/PIP (63.7 L m-2 h-1 and lemon yellow (LY)/NaCl selectivity of 664.0) membranes under 0.4 MPa operation pressure are much higher than PIP-only and HBP-NH2/PIP membranes. At the same time, this project also studied the membrane desalination process in a simulated high-salinity dye/salt mixture system to provide a theoretical basis and technical support for the actual dye desalination process.

Colloidal 2D Covalent Organic Framework-Tailored Nanofiltration Membranes for Precise Molecular Sieving

Covalent organic frameworks (COFs) with tunable pore sizes and ordered structures are ideal materials for engineering nanofiltration (NF) membranes. However, most of the COFs prepared by solvothermal synthesis are unprocessable powders and fail to form well-structured membranes, which seriously hinders the development of COF NF membranes. Herein, colloidal 2D-COFs with processable membrane formation ability were synthesized by oil-in-water emulsion interfacial polymerization technology. COF NF membranes with tailored thickness and surface charge were fabricated via a layer-by-layer (LBL) assembly strategy. The prepared COF NF membrane achieved precise sieving of dye molecules with high permeance (85 L·m-2·h-1·bar-1). In this work, the strategy of prepared COF NF membranes based on colloid 2D-COF LBL assembly is proposed for the first time, which provides a new idea for the on-demand design and preparation of COF membranes for precise molecular sieving.

Tailoring the performance of composite PEI nanofiltration membranes via incorporating activated cyclodextrins

Cyclodextrins (CDs) with unique cavity structures have been used as materials for nanofiltration membrane fabrications. In the present work, the activated CD (O-CD), oxidated by NaIO4, and polyethyleneimine (PEI) were co-deposited on a hydrolyzed polyacrylonitrile support, post-treated by glycerol protection and heating treatment, to prepare nanofiltration membranes with low molecular weight cut-off (MWCO). As the cavities in CD present and the aldehyde groups introduced after oxidation, the O-CDs were expected to crosslink the PEI layer and provide extra permeating channels. The filtration experiments showed that the incorporation of O-CDs improved the permeances of the O-CD-PEI/HPAN nanofiltration membranes. The performance can be tailored by the control of the loading or the oxidation degree of the O-CD. At optimal conditions, the permeance increment was nearly double (from 9.2 to 21.1 Lm-2·h-1·bar-1). While the selectivity was without significant sacrifice, the rejection of PEG 200 remained around 90%. Meanwhile, the membrane stability was demonstrated by pro-longed filtratiing a PEG 200 aqueous solution. The constant permeance and rejection confirmed the O-CD-PEI/HPAN membranes were stable. The incorporation of activated CD in PEI offers a facile strategy to promote the permeance of PEI-based membranes.

Interfacial Polymerization of Highly Active Thiolated Cyclodextrin for the Fabrication of a Loose Nanofiltration Membrane with a Chlorine-Resistant Poly(thioester) Linkage

Cyclodextrins have been frequently used to fabricate membranes via interfacial polymerization (IP). However, the relatively low reactivity of pristine cyclodextrins often induces a lower cross-linking density and unsatisfactory separation performance. In this work, to introduce a highly active thiolated β-cyclodextrin (CD-SH) monomer into IP progress, we constructed a dense and porous poly(thioester) linkage on a commercial membrane surface with loose nanofiltration by IP of CD-SH and trimesoyl trichloride (TMC) as the monomer in an aqueous phase and organic phase separately for the first time. Furthermore, the reactivity of CD-SH has been fully demonstrated by the two-phase IP aiming at unmodified β-CD, a CD-SH/TMC freestanding membrane with a thicker interfacial layer and a smoother surface, and a PAN/CD-SH membrane with a narrow porous distribution. The composite membrane possessed superior separation performance for a high rejection (83.1-99.6%) of different anionic dyes and a low rejection (<20%) of salts, as well as a high-efficiency sieving ability of dye/dye and dye/salt mixtures. The membrane with a poly(thioester) selective layer could steadily operate in a long-term filtration test and exhibit great stability, chloride-resistance performance, and recyclability.

Green and Rapid Synthesis of Acridine-Functionalized Covalent Organic Polymers for Photocatalysis by Combining Sonochemistry and Ion Induction

Covalent organic polymers (COPs) are powerful candidates for achieving the visible-light-driven degradation of organic pollutants by virtue of structural designability, but their synthesis relies on harmful reagents and high temperatures, which weakens their associated green merits. Here, we report a novel strategy for combining sonochemistry with ion induction for the rapid preparation of acridine-functionalized COPs in green and mild aqueous solutions with tunable high yields of 80 to 90%. Photochemical studies reveal the ability of these COPs to harvest visible light and their sufficient conduction potentials for generating superoxide radicals. Furthermore, the photodegradation of methylene blue confirms the good photocatalytic activity and reusability of the zinc ion-based acridine-functionalized COP, which achieves 90.8% removal in 150 min and retains 82.5% activity after 5 reuse cycles, with a rate constant of up to 3.2 times that of commercial titanium dioxide nanoparticles. This strategy paves the way for the green, rapid, and mild synthesis of acridine-functionalized COPs, enabling visible light photocatalytic degradation for water treatment and energy conversion to advance in a thoroughly environmentally friendly and cost-effective manner.

Next-Generation Water Treatment: Exploring the Potential of Biopolymer-Based Nanocomposites in Adsorption and Membrane Filtration

This review article focuses on the potential of biopolymer-based nanocomposites incorporating nanoparticles, graphene oxide (GO), carbon nanotubes (CNTs), and nanoclays in adsorption and membrane filtration processes for water treatment. The aim is to explore the effectiveness of these innovative materials in addressing water scarcity and contamination issues. The review highlights the exceptional adsorption capacities and improved membrane performance offered by chitosan, GO, and CNTs, which make them effective in removing heavy metals, organic pollutants, and emerging contaminants from water. It also emphasizes the high surface area and ion exchange capacity of nanoclays, enabling the removal of heavy metals, organic contaminants, and dyes. Integrating magnetic (Fe2O4) adsorbents and membrane filtration technologies is highlighted to enhance adsorption and separation efficiency. The limitations and challenges associated are also discussed. The review concludes by emphasizing the importance of collaboration with industry stakeholders in advancing biopolymer-based nanocomposites for sustainable and comprehensive water treatment solutions.

Nanoremediation strategies to address environmental problems

A rapid rise in population, extensive anthropogenic activities including agricultural practices, up-scaled industrialization, massive deforestation, etc. are the leading causes of environmental degradation. Such uncontrolled and unabated practices have affected the quality of environment (water, soil, and air) synergistically by accumulating huge quantities of organic and inorganic pollutants in it. Environmental contamination is posing a threat to the existing life on the Earth, therefore, demands the development of sustainable environmental remediation approaches. The conventional physiochemical remediation approaches are laborious, expensive, and time-consuming. In this regard, nanoremediation has emerged as an innovative, rapid, economical, sustainable, and reliable approach to remediate various environmental pollutants and minimize or attenuate the risks associated with them. Owing to their unique properties such as high surface area to volume ratio, enhanced reactivity, tunable physical parameters, versatility, etc. nanoscale objects have gained attention in environmental clean-up practices. The current review highlights the role of nanoscale objects in the remediation of environmental contaminants to minimize their impact on human, plant, and animal health; and air, water, and soil quality. The aim of the review is to provide information about the applications of nanoscale objects in dye degradation, wastewater management, heavy metal and crude oil remediation, and mitigation of gaseous pollutants including greenhouse gases.

Loose Nanofiltration Membrane Incorporating CeZnFe Layered Double Hydroxide with Enhanced Dye/Salt Separation Performance and Self-Cleaning Ability

The high-salinity wastewater from the textile industry faces a significant challenge in effectively separating dyes and salts. In this study, a CeZnFe-layered double hydroxide (LDH)-incorporated nanofiltration (LNF) membrane was fabricated using the conventional interfacial polymerization (IP) technique to fractionate dyes and salts within the wastewater. The impact of CeZnFe LDH on various aspects of membrane performance was examined, including water flux, dye removal efficiency, dye/salt separation capability, self-cleaning ability, and membrane integrity. The addition of LDHs resulted in improved membrane surface hydrophilicity, thereby enhancing water flux. The optimized TFN membrane (0.050 wt% LDH in PIP solution) significantly improved pure water flux, exceeding 150%. All TFN membranes exhibited excellent performance in dye and salt fractionation (93% for Congo red, 2.6% for NaCl, and 40.7% for Na2SO4). Also, excellent self-cleaning ability was observed for the optimized membrane, exhibiting a remarkable water flux recovery rate after three operation cycles. Moreover, including CeZnFe LDH in the optimized TFN membrane played a significant role in enhancing membrane integrity. This study provides new inspiration for fabricating self-cleaning loose NF membranes using CeZnFe LDH for effective dye/salt separation.

New technology for preparing energetic materials by nanofiltration membrane (NF): rapid and efficient preparation of high-purity ammonium dinitramide (ADN)

The development of environment-friendly and non-toxic green energetic materials and their safe, environmentally friendly, and economical production is very important to the national economy and national security. As an innovative, efficient, and environmentally friendly energetic material, the preferred preparation method of ammonium dinitramide (ADN) is the nitro-sulfur mixed acid method, which has the advantages of high yield, simple method, and easy access to raw materials. However, the large number of inorganic salt ions introduced by this method limits the large-scale production of ADN. Nanofiltration (NF) has been widely used in various industrial processes as a separation method with high separation efficiency and simple operation. In this study, NF was used for the desalination and purification of ADN synthesized by the mixed acid method. The effects of NF types, operation process (pressure, temperature, and feed solution concentration) on desalination efficiency, and membrane flux during purification were examined. The results showed that 600D NF could achieve the efficient desalination and purification of ADN. It was verified that the highest desalination and purification efficiency was achieved at 2 MPa pressure, 25 °C, and 1 time dilution of the feed solution, and the membrane flux of the desalination and purification process was stable. Under the optimized process conditions, the removal rate of inorganic salts and other impurities reached 99% (which can be recycled), the purity of ADN reached 99.8%, and the recovery rate reached 99%. This process has the potential for the large-scale production of ADN and provides a new process for the safe, efficient, and cheap preparation of energetic materials.

Thin-Film Nanocomposite (TFN) Membranes for Water Treatment Applications: Characterization and Performance

Thin-film nanocomposite (TFN) membranes have been widely investigated for water treatment applications due to their promising performance in terms of flux, salt rejection, and their antifouling properties. This review article provides an overview of the TFN membrane characterization and performance. It presents different characterization techniques that have been used to analyze these membranes and the nanofillers within them. The techniques comprise structural and elemental analysis, surface and morphology analysis, compositional analysis, and mechanical properties. Additionally, the fundamentals of membrane preparation are also presented, together with a classification of nanofillers that have been used so far. The potential of TFN membranes to address water scarcity and pollution challenges is significant. This review also lists examples of effective TFN membrane applications for water treatment. These include enhanced flux, enhanced salt rejection, antifouling, chlorine resistance, antimicrobial properties, thermal stability, and dye removal. The article concludes with a synopsis of the current status of TFN membranes and future perspectives.

Selective separation of dye/salt mixture using diatomite-based sandwich-like membrane

A novel nanofiltration membrane was developed by entrapping a layer of modified diatomaceous earth between two layers of electrospun polysulfone (E-PSf) nanofibers. The diatomaceous earth particles and the fabricated membrane were characterized using FTIR, SEM, EDS, zeta potential, and water contact angle techniques. The static adsorption and dynamic separation of pristine E-PSF and sandwich-like membranes for methylene blue (MB) with/without salt were investigated under different operating conditions. The Langmuir model suited the MB adsorption isotherm data with a linear regression correlation coefficient (R²) >0.9955. As pH increased, both flux and MB rejection of the sandwich-like membrane improved by up to 183.8 LMH and 99.7%, respectively, when operated under gravity. The water flux of the sandwich-like membrane was sharply increased by increasing the pressure up to 19,518.2 LMH at 4.0 bar. However, this came at the expense of MB rejection (10.93%) and reduced its practical impact. At a high salt concentration, the sandwich-like membrane also indicated remarkable dye/salt separation with a higher permeation of salt (<0.2% NaCl rejection) and MB rejection (>99%). The performance of the regenerated diatomaceous material and membrane was maintained during five cycles of operation compared to that of the original ones.

Low-pressure thin-film composite nanofiltration membranes with enhanced selectivity and antifouling property for effective dye/salt separation

For better sustainable resource recovery and elevating the separation efficiency of dye/salt mixture, it is essential to develop an appropriate nanofiltration membrane for the treatment of textile dyeing wastewater containing relatively smaller molecule dyes. In this work, a novel composite polyamide-polyester nanofiltration membrane was fabricated by tailoring amino functionalized quantum dots (NGQDs) and β-cyclodextrin (CD). An in-situ interfacial polymerization occurred between the synthesized NGQDs-CD and trimesoyl chloride (TMC) on the modified multi-carbon nanotubes (MWCNTs) substrate. The incorporation of NGQDs significantly elevated the rejection (increased by ∼ 45.08%) of the resultant membrane for small molecular dye (Methyl orange, MO) compared to the pristine CD membrane at low pressure (1.5 bar). The newly developed NGQDs-CD-MWCNTs membrane exhibited enhanced water permeability without compromising the dye rejection compared to the pure NGQDs membrane. The improved performance of the membrane was primarily attributed to the synergistic effect of functionalized NGQDs and the special hollow-bowl structure of CD. The optimal NGQDs-CD-MWCNTs-5 membrane expressed pure water permeability of 12.35 L m^-2h^-1 bar^-1 at the pressure of 1.5 bar. Noteworthily, the NGQDs-CD-MWCNTs-5 membrane not only showed high rejection for the larger molecular dye of Congo Red (CR, 99.50%) but also for the smaller molecular dye of MO (96.01%) and Brilliant Green (BG, 95.60%) with the permeability of 8.81, 11.40, and 6.37 L m^-2h^-1 bar^-1, respectively at low pressure (1.5 bar). The rejection of inorganic salts by the NGQDs-CD-MWCNTs-5 membrane was 17.20% for sodium chloride (NaCl), 14.30% for magnesium chloride (MgCl₂), 24.63% for magnesium sulfate (MgSO₄), and 54.58% for sodium sulfate (Na₂SO₄), respectively. The great rejection of dyes remained in the dye/salt binary mixed system (higher than 99% for BG and CR, <21% for NaCl). Importantly, the NGQDs-CD-MWCNTs-5 membrane exhibited favorable antifouling performance and potential good operation stability performance. Consequently, the fabricated NGQDs-CD-MWCNTs-5 membrane suggested a prospective application for the reuse of salts and water in textile wastewater treatment owing to the effective selective separation performance.

Interpenetrating polymer networks for desalination and water remediation: a comprehensive review of research trends and prospects

Interpenetrating polymer network (IPN) architectures have gained a lot of interest in recent decades, mainly due to their wide range of applications including water treatment and environmental remediation. IPNs are composed of two or more crosslinked polymeric matrices that are physically entangled but not chemically connected. In polymer science, the interpenetrating network structure with its high polymer chain entanglement is commonly used to generate materials with many functional properties, such as mechanical robustness and adaptable structure. In order to remove a targeted pollutant from contaminated water, it is feasible to modify the network architectures to increase the selectivity by choosing the monomer appropriately. This review aims to give a critical overview of the recent design concepts of IPNs and their applications in desalination and water treatment and their future prospects. This article also discusses the inclusion of inorganic nanoparticles into traditional polymeric membrane networks and its advantages. In the first part, the current scenario for desalination, water pollution and conventional desalination technologies along with their challenges is discussed. Subsequently, the main strategies for the synthesis of semi-IPNs and full-IPNs, and their relevant properties in water remediation are presented based on the nature of the networks and mechanism, with an emphasis on the IPN membrane. This review article has thoroughly investigated and critically assessed published works that describe the latest study on developing IPN membranes, hydrogels and composite materials in water purification and desalination. The goal of this critical analysis is to elicit fresh perspectives regarding the application and advantages of IPNs in desalination and water treatment. This article will also provide a glimpse into future areas of research to address the challenges relating to advanced water treatment as well as its emerging sustainable approaches. The study has put forward a convincing justification and establishes the relevance of IPNs being one of the most intriguing and important areas for achieving a sustainable generation of advanced materials that could benefit mankind.

A review on polyester and polyester-amide thin film composite nanofiltration membranes: Synthesis, characteristics and applications

Nanofiltration (NF) membranes have been widely used in various fields including water treatment and other separation processes, while conventional thin film composite (TFC) membranes with polyamide (PA) selective layers suffer the problems of fouling and chlorine intolerance. Due to the abundant hydrophilic hydroxyl groups and ester bonds free from chlorine attack, the TFC membranes composed of polyester (PE) or polyester-amide (PEA) selective layers have been proven to possess enhanced anti-fouling properties and superior chlorine resistance. In this review, the research progress of PE and PEA nanofiltration membranes is systematically summarized according to the variety of hydroxyl-containing monomers for membrane fabrication by the interfacial polymerization (IP) reaction. The synthesis strategies as well as the mechanisms for tailoring properties and performance of PE and PEA membranes are analyzed, and the membrane application advantages are demonstrated. Moreover, current challenges and future perspectives of the development of PE and PEA nanofiltration membranes are proposed. This review can offer guidance for designing high-performance PE and PEA membranes, thereby further promoting the efficacy of nanofiltration.

Recent Advanced Development of Acid-Resistant Thin-Film Composite Nanofiltration Membrane Preparation and Separation Performance in Acidic Environments

Membrane filtration technology has attracted extensive attention in academia and industry due to its advantages of eco-friendliness related to environmental protection and high efficiency. Polyamide thin-film composite nanofiltration (PA TFC NF) membranes have been widely used due to their high separation performance. Non-acid-resistant PA TFC NF membranes face tremendous challenges in an acidic environment. Novel and relatively acid-resistant polysulfonamide-based and triazine-based TFC NF membranes have been developed, but these have a serious trade-off in terms of permeability and selectivity. Hence, how to improve acid resistance of TFC NF membranes and their separation performance in acidic environments is a pivotal issue for the design and preparation of these membranes. This review first highlights current strategies for improving the acid resistance of PA TFC NF membranes by regulating the composition and structure of the separation layer of the membrane performed by manipulating and optimizing the construction method and then summarizes the separation performances of these acid-resistant TFC NF membranes in acidic environments, as studied in recent years.

Recycling the High-Salinity Textile Wastewater by Quercetin-Based Nanofiltration Membranes with Minimal Water and Energy Consumption

Effective recovery of dyes and salts from textile wastewater by nanofiltration (NF) remains a serious challenge due to the high consumption of water and energy caused by the limited performance of the available membranes. Herein, a novel strategy is described to prepare loose polyester NF membranes by using renewable quercetin as the aqueous monomer for fractionation of high salinity textile wastewater with minimal water and energy consumption. Compared with NF270, taken as the reference membrane, the QE-0.2/TMC-0.2 membrane significantly improved the efficiency for dye/salt fractionation by 288%. The water consumption was also decreased by 42.9%. The efficiency is attributed to an ultrahigh water permeance of 198 ± 2.1 L^-1 m^-2 h^-1 bar^-1 with a high selectivity of 123 (extremely low NaCl rejection of 1.6% and high Congo red rejection of 99.2%). The optimal quercetin-based membrane had an ultrathin separation layer of about 39 ± 1.2 nm with good hydrophilicity and negative charge density. Moreover, this work includes a novel method of comparison with a theoretically ideal membrane, which shows that both the energy and water consumption are near their theoretical minimum. This strategy is expected to save energy and minimize carbon emissions for membrane-based wastewater treatment systems.

An Overview of the Modification Strategies in Developing Antifouling Nanofiltration Membranes

Freshwater deficiency has become a significant issue affecting many nations' social and economic development because of the fast-growing demand for water resources. Nanofiltration (NF) is one of the promising technologies for water reclamation application, particularly in desalination, water, and wastewater treatment fields. Nevertheless, membrane fouling remains a significant concern since it can reduce the NF membrane performance and increase operating expenses. Consequently, numerous studies have focused on improving the NF membrane's resistance to fouling. This review highlights the recent progress in NF modification strategies using three types of antifouling modifiers, i.e., nanoparticles, polymers, and composite polymer/nanoparticles. The correlation between antifouling performance and membrane properties such as hydrophilicity, surface chemistry, surface charge, and morphology are discussed. The challenges and perspectives regarding antifouling modifiers and modification strategies conclude this review.

Fabrication of Loose Nanofiltration Membranes with High Rejection Selectivity between Natural Organic Matter and Salts for Drinking Water Treatment

Loose nanofiltration (LNF) membranes with a molecular weight cut-off (MWCO) of about 1000 Da and high surface negative charge density have great application potential for drinking water treatment pursuing high rejection selectivity between natural organic matter (NOM) and mineral salts. This study was conducted to exploit the novel method coupling non-solvent induced phase separation (NIPS) and interfacial polymerization (IP) for the preparation of high-performance LNF membranes. A number of LNF membranes were synthesized by varying the polyethersulfone (PES) and piperazine (PIP) concentrations in the cast solution for the PES support layer preparation. Results showed that these two conditions could greatly affect the membrane water permeance, MWCO and surface charge. One LNF membrane, with a water permeance as high as 23.0 ± 1.8 L/m²/h/bar, when used for the filtration of conventional process-treated natural water, demonstrated a rejection of NOM higher than 70% and a low rejection of mineral salts at about 20%. Both the mineral salts/NOM selectivity and permselectivity were superior to the currently available LNF membranes as far as the authors know. This study demonstrated the great advantage of the NIPS-IP method for the fabrication of LNF membranes, particularly for the advanced treatment of drinking water.

Metal-polyphenol cross-linked titanium carbide membranes with stable interlayer spacing for efficient wastewater treatment

Membranes based on transition metal carbides/nitrides (MXenes) have significant water treatment potential because of their unique molecular sieving properties and excellent permeation performance. However, hydrophilic MXenes swell upon water immersion, and improving their stability remains challenging. In this study, a Fe³⁺-tannic acid (TA) complex was used as a cross-linker and surface modifier to prepare high-performance titanium carbide (Ti₃C₂T_x) MXene laminar membranes. Fe³⁺-TA formation on the nanosheets increased the interlayer spacing and stabilized the laminar structure. The membrane with the highest performance among the as-prepared membranes exhibited a high water permeance of 90.5 L/m^-2(-|-)h^-1 bar^-1 (which is twice that of the pristine Ti₃C₂T_x membrane) and good separation efficiency (methyl blue rejection rate: ∼99.8 %; Na₂SO₄ rejection rate: ∼5.0 %). Furthermore, the Fe³⁺-TA complex enhanced the membrane hydrophilicity, resulting in excellent antifouling properties. This study provides an environmentally friendly and facile method for fabricating two-dimensional loose nanofiltration membranes for textile wastewater treatment.

Fabrication of ballpoint-ink via encapsulating inorganic pigments in microemulsion gels

The fabrication of ballpoint-ink might open up a new perspective on physico-chemical solubility thermodynamics. In this report, we present a method to encapsulate inorganic pigments, such as Fe(CNS)₃ (red), Fe₂Fe(CN)₆ (blue), CdS (yellow), and CuS (black) into w/o microemulsion gels. The area of w/o microemulsions was first determined by titrating surfactants Tween-60 into the given composition of water and cyclohexane in the pseudo-three phase diagram. Three prosperous phase areas were successfully mapped using this method, namely: microemulsion (w/o, and o/w) or (μE), lamellar liquid crystal (L_α), and hexagonal liquid crystal (H_α), respectively. The results show that inorganic pigments were well soluble in the w/o microemulsion gel of the Tween-60/cyclohexane/water system. The highest solubility of inorganic pigments in the microemulsion gel is 3.63 ± 0.05 mg g⁻¹ for the red pigment of Fe(CNS)₃, and the lowest is 2.92 ± 0.05 mg g⁻¹ for the yellow pigment of CdS. Hence, the solubility limit distribution for all pigments is 2.9 ± 0.05 <>3.63 ± 0.05 mg g⁻¹. The cation and anion size strongly affected the inorganic pigments' solubility in the w/o-microemulsion system. Some quantity of the ink-made of inorganic pigments encapsulated in the microemulsion gel has been inserted into empty ballpoint sleeves as prototypes. The resulting self-made inks demonstrated that the physical appearances of the ink could mimic the factory-made inks. Nevertheless, the self-made ink should be investigated further for long lifespan use, especially for long-term stability and corrosion resistance.

The way to fabricate ballpoint ink from microemulsions gel.