Peroxymonosulfate catalytic degradation of persistent organic pollutants by engineered catalyst of self-doped iron/carbon nanocomposite derived from waste toner powder

The role of physicochemical marble processing wastewater treatment sludge in the production of new generation pyrolysis char from waste polypropylene

The effects of marble processing wastewater physicochemical treatment sludge (K1) on polypropylene (PP) waste pyrolysis were investigated by lab-scale batch pyrolysis system. PP-K1 proportions and pyrolysis temperature were studied as variables and both were found to have influences onto pyrolysis char, oil/tar, gas fractions distribution, as well as pyrolysis char characteristics (determined via SEM, EDX, FTIR, TGA and XRD analyses). The influence of K1 could be related to its high mineral composition (CaCO3, CaMg(CO3)2 and (Mg0.03Ca0.97)(CO3)) which also detected in the char products. K1 acts as catalyst and remained unchanged in thermochemical reactions below 700°C. The main thermal degradation of PP occurs around 400-470°C, although it starts at about 300-350°C, whereas, K1 resulted in more thermal degradation at 300°C pyrolysis. As K1 dose increased, pyrolysis chars became more thermally stable with the pyrolysis temperature. Diverse types of chars in terms of porosity, thermal strength and chemical structure were produced with PP + K1 as compared to the PP chars. For example, with 10%-20% K1 doses, the chars are in aromatic structure while chars become aliphatic when K1 dosage increased to 30% or above. The structural diversity made these chars new products that can be used as raw material for subsequent purposes. This study provided a basis for the chars' physical and chemical properties which are needed for further research to develop new generation evaluation areas for them. Therefore, a new symbiotic upcycling approach has been presented for PP wastes and marble processing wastewater treatment sludge.

Surface modification of toner-based recyclable iron oxide self-doped graphite nanocomposite to enhance methylene blue and tetracycline adsorption

An innovative task was undertaken to convert ubiquitous and toxic electronic waste, waste toner powder (WTP), into novel adsorbents. Alkaline modification with KOH, NaOH, and NH4OH was employed for the first time to synthesize a series of surface-modified WTP with enhanced dispersibility and adsorption capacity. XRD, XRF, FTIR, and BET analyses confirmed that the prepared KOH-WTP, NaOH-WTP, and NH4OH-WTP were oxygen-functionalized self-doped iron oxide-graphite nanocomposites. The prepared adsorbents were used to remove methylene blue and tetracycline from aqueous solutions. KOH-WTP (0.1 g/100 mL) adsorbed 80% of 10 mg/L methylene blue within 1 h, while 0.1 g/100 mL NH4OH-WTP removed 72% of 10 mg/L tetracycline in 3 h. Exploring surface chemistry by altering solution pH and temperature suggested that hydrogen bonding, electrostatic interactions, π-π electron stacking, and pore filling were plausible adsorption mechanisms. Scanning electron microscopy revealed a diminishing adsorbents porosity after adsorption proving the filling of pores by the adsorbates. KOH-WTP and NH4OH-WTP removed 77% and 61% of methylene blue and tetracycline respectively in the fourth reuse. The adsorption data of methylene blue and tetracycline fitted the Freundlich isotherm model. The maximum adsorption capacities of KOH-WTP and NH4OH-WTP for methylene blue and tetracycline were 59 mg/g and 43 mg/g respectively. The prepared adsorbents were also compared with other adsorbents to assess their performance. The transformation of waste toner powder into magnetically separable oxygen-functionalized WTP with outstanding recyclability and adsorption capacity showcases a significant advancement in sustainable wastewater treatment. This further aligns with the principles of the circular economy through the utilization of toxic e-waste in value-added applications. Additionally, magnetic separation of surface-modified WTP post-treatment can curtail filtration and centrifugation expenses and adsorbent loss during wastewater treatment.

Green rGO/FeNPs nanocomposites activated peroxydisulfate for the removal of mixed 17β-estradiol and estriol

Reduced graphene oxide/iron nanoparticles (rGO/FeNPs) synthesized by the chemical method have been used in Fenton oxidation of organic contaminants, yet little is known about biosynthesized rGO/FeNPs using green tea extract (GT) as how to activate persulfate in sulfate radical-based advanced oxidation processes. In this study, rGO/FeNPs were used to activate peroxydisulfate (PDS) for 17β-estradiol (βE2) and estriol (E3) removal. The rGO/FeNPs-PDS system removed 83.6% of βE2 and 62.5% of E3 within 240 min, which was confirmed by a combination of adsorption and degradation via both radical and non-radical pathways. Four main reactive species in βE2 and E3 degradation were observed, i.e., hydroxyl radical (·OH), sulfate radical (SO4·-), singlet oxygen (1O2) and electron transfer, with the respective contributions of ·OH (32.9 and 34.7%), SO4·- (16.1 and 19.7%), 1O2 (12.2 and 14.1%) and electron transfer (8.0 and 7.2%). Analysis of X-ray photoelectron spectroscopy (XPS), Fourier transform infrared (FTIR), Electron Paramagnetic Resonance (EPR) and electrochemical measurements all indicated that beside the well-known role of Fe, CO from rGO through the generation of ·OH, SO4·-, 1O2 and electron transfer, as well as GT through electron transfer also participated in the activation of PDS. Finally, the degradation pathways of βE2/E3 were proposed. Overall, this study provides a new insight into the biosynthesis of rGO/FeNPs to activate PDS for the oxidation of mixed emerging contaminants.

Recent updates on remediation approaches of environmentally occurring pollutants using visible light-active nano-photocatalysts

Photocatalysis emerges as a potential remedy for the issue of an unreliable light source. Recognized as the most dependable and potent energy source sustaining life on Earth, sunlight offers a promising solution. Sunlight is abundant and free, operational costs associated with running photocatalytic system using nanoparticles are often lower compared to system relying on artificial light source. The escalating problem of water pollution, particularly in highly industrialized nations, necessitates effective wastewater treatment methods. These methods aim to combat elevated pollution levels, encompassing pharmaceuticals, dyes, flame retardants, and pesticide components. Advanced oxidation processes within photocatalytic wastewater treatment exhibit substantial promise for removing complex organic pollutants. Doped nanomaterials, with their enhanced properties, enable efficient utilization of light. Coupled nanomaterials present significant potential in addressing both water and energy challenges by proficiently eliminating persistent pollutants from environment. Photocatalysis when exposed to sunlight can absorb photons and generate e- h + pairs. This discussion briefly outlines the wastewater treatment facilitated by interconnected nanomaterials, emphasizing their role in water-energy nexus. In exploring the capabilities of components within a functional photocatalyst, a comprehensive analysis of both simple photocatalysts and integrated photocatalytic systems is undertaken. Review aims to provide detailed explanation of the impact of light source on photon generation and significance of solar light on reaction kinetics, considering various parameters such as catalyst dosage, pH, temperature, and types of oxidants. By shedding light on these aspects, this review seeks to enhance our understanding of intricate processes involved in photocatalysis and its potential applications in addressing contemporary environmental challenges.

A review of metallurgical slags as catalysts in advanced oxidation processes for removal of refractory organic pollutants in wastewater

With the rapid growth of the metallurgical industry, there is a significant increase in the production of metallurgical slags. The waste slags pose significant challenges for their disposal because of complex compositions, low utilization rates, and environmental toxicity. One promising approach is to utilize metallurgical slags as catalysts for treatment of refractory organic pollutants in wastewater through advanced oxidation processes (AOPs), achieving the objective of "treating waste with waste". This work provides a literature review of the source, production, and chemical composition of metallurgical slags, including steel slag, copper slag, electrolytic manganese residue, and red mud. It emphasizes the modification methods of metallurgical slags as catalysts and the application in AOPs for degradation of refractory organic pollutants. The reaction conditions, catalytic performance, and degradation mechanisms of organic pollutants using metallurgical slags are summarized. Studies have proved the feasibility of using metallurgical slags as catalysts for removing various pollutants by AOPs. The catalytic performance was significantly influenced by slags-derived catalysts, catalyst modification, and process factors. Future research should focus on addressing the safety and stability of catalysts, developing green and efficient modification methods, enhancing degradation efficiency, and implementing large-scale treatment of real wastewater. This work offers insights into the resource utilization of metallurgical slags and pollutant degradation in wastewater.

Highly dispersed Fe7S8 anchored on sp2/sp3 hybridized carbon boosting peroxymonosulfate activation for enhanced EOCs elimination though singlet oxygen-dominated nonradical pathway

The synergistic effect of carbon materials with high sp2/sp3 hybridized carbon ratio and metal materials can enhance the efficiency of peroxymonosulfate (PMS) based advanced oxidation processes. In this study, a composite of highly dispersed Fe7S8 anchored on sp2/sp3 hybridized carbon (Fe7S8@HC) was developed by a facile synthesis for PMS activation. Within 10 min, the removal efficiency of the target pollutant doxycycline (DOX) could reach ca. 96 % in optimal Fe7S8@HC/PMS system through a 1O2-dominated non-radical pathway. Correlation mechanism analysis revealed that thiophene S, sp2/sp3 ratio and Fe(II) were critical factors for elongating of the O-O bond of PMS. Moreover, the Fe7S8@HC/PMS system exhibited favorable adaptability to interference such as common inorganic anions, humic acid and pH changes and could effectively remove various organic pollutants with low ionization potential. Moreover, the system maintained high DOX removal efficiency by running 30 cycles in a continuous flow reactor. Finally, susceptible sites of DOX and four degradation pathways were proposed by density functional theory calculation and LC-MS detection. This work not only offered new insights into the design of high-performance catalysts combining metal and biomass-based carbon materials, but also provided technical support for the remediation of water bodies containing emerging organic contaminants.

Straw-derived biochar for the removal of antibiotics from water: Adsorption and degradation mechanisms, recent advancements and challenges

Antibiotics, a kind of containments with the properties of widely distributed and difficult to degrade, has aroused extensive attention in the world. As a prevalent agricultural waste, straws can be utilized to prepare biochar (straw-derived biochar, SBC) to remove antibiotics from aquatic environment. To date, although a number of review papers have summarized and discussed research on biochar application in wastewater treatment and soil remediation, there are few reviews on SBC for antibiotic removal. Due to the limitations of poor adsorption and degradation performance of the pristine SBC, it is necessary to modify SBC to improve its applications for antibiotics removal. The maximum antibiotic removal capacity of modified SBC could reach 1346.55 mg/g. Moreover, the adsorption mechanisms between modified SBC and antibiotics mainly involve π-π interactions, electrostatic interactions, hydrophobic interactions, and charge dipole interactions. In addition, the modified SBC could completely degrade antibiotics within 6 min by activating oxidants, such as PS, PDS, H2O2, and O3. The mechanisms of antibiotic degradation by SBC activated oxidants mainly include free radicals (including SO4•-, •OH, and O2•-) and non-free radical pathway (such as, 1O2, electrons transfer, and surface-confined reaction). Although SBC and modified SBC have demonstrated excellent performance in removing antibiotics, they still face some challenges in practical applications, such as poor stability, high cost, and difficulties in recycling. Therefore, the further research directions and trends for the development of SBC and biochar-based materials should be taken into consideration.

Harnessing the power of natural minerals: A comprehensive review of their application as heterogeneous catalysts in advanced oxidation processes for organic pollutant degradation

The release of untreated wastewater into water bodies has become a significant environmental concern, resulting in the accumulation of refractory organic pollutants that pose risks to human health and ecosystems. Wastewater treatment methods, including biological, physical, and chemical techniques, have limitations in achieving complete removal of the refractory pollutants. Chemical methods, particularly advanced oxidation processes (AOPs), have gained special attention for their strong oxidation capacity and minimal secondary pollution. Among the various catalysts used in AOPs, natural minerals offer distinct advantages, such as low cost, abundant resources, and environmental friendliness. Currently, the utilization of natural minerals as catalysts in AOPs lacks thorough investigation and review. This work addresses the need for a comprehensive review of natural minerals as catalysts in AOPs. The structural characteristics and catalytic performance of different natural minerals are discussed, emphasizing their specific roles in AOPs. Furthermore, the review analyzes the influence of process factors, including catalyst dosage, oxidant addition, pH value, and temperature, on the catalytic performance of natural minerals. Strategies for enhancing the catalytic efficiency of AOPs mediated by natural minerals are explored, mainly including physical fields, reductant addition, and cocatalyst utilization. The review also examines the practical application prospects and main challenges associated with the use of natural minerals as heterogeneous catalysts in AOPs. This work contributes to the development of sustainable and efficient approaches for organic pollutant degradation in wastewater.

Biochar/layered double hydroxides composites as catalysts for treatment of organic wastewater by advanced oxidation processes: A review

Heterogeneous advanced oxidation process has been widely studied as an effective method for removing organic pollutants in wastewater, but the development of efficient catalysts is still challenging. This review summaries the present status of researches on biochar/layered double hydroxides composites (BLDHCs) as catalysts for treatment of organic wastewater. The synthesis methods of layered double hydroxides, the characterizations of BLDHCs, the impacts of process factors influencing catalytic performance, and research advances in various advanced oxidation processes are discussed in this work. The integration of layered double hydroxides and biochar provides synthetic effects for improving pollutant removal. The enhanced pollutant degradation in heterogeneous Fenton, sulfate radical-based, sono-assisted, and photo-assisted processes using BLDHCs have been verified. Pollutant degradation in heterogeneous advanced oxidation processes using BLDHCs is influenced by process factors such as catalyst dosage, oxidant addition, solution pH, reaction time, temperature, and co-existing substances. BLDHCs are promising catalysts due to the unique features including easy preparation, distinct structure, adjustable metal ions, and high stability. Currently, catalytic degradation of organic pollutants using BLDHCs is still in its infancy. More researches should be conducted on the controllable synthesis of BLDHCs, the in-depth understanding of catalytic mechanism, the improvement of catalytic performance, and large-scale application of treating real wastewater.

Rapid PFOS mineralization with peroxydisulfate activation process mediated by N modified Fe-based catalyst

As the cheap and efficient catalysts, the iron-based catalysts have been considered as one of the most promising catalysts for peroxydisulfate (PDS) activation and the development of high-performance iron-based catalysts are attracting growing attentions. In this work, a magnetic Fe-based catalysts (Fe/NC-1000) was obtained by using Fe modified ZIF-8 as the precursor and used to activate the PDS for the degradation of perfluorooctane sulphonate (PFOS). Morphology and structure analysis showed that the resulted Fe/NC-1000 catalyst was displayed porous spheres (40-60 nm) and mainly composed of Fe0, FeNx and carbon. When Fe/NC-1000 was employed to activate the PDS (0.1 g/L of catalyst dosage, 0.5 g/L of PDS dosage and at initial pH of 4.6), the Fe/NC-1000/PDS system exhibited excellent efficiency (97.9 ± 0.1) % for PFOS (10 mg/L) degradation within 30 min. The quenching tests and EPR results revealed that the Fe/NC-1000/PDS system degraded PFOS primarily through singlet oxygen (1O2) evolution and electron-transfer process. Besides, based on the degradation byproducts determined by LC-MS-MS, the PFOS first occurred de-sulfonation to form PFOA, and then the resulted PFOA underwent stepwise defluorination in the Fe/NC-1000/PDS system. Density Functional Theory (DFT) calculations and electrochemistry tests strongly confirmed that Fe/NC-1000 exhibited high electron transfer efficiency, resulting in promoted performance on activating PDS. Importantly, the results of Ecological Structure-Activity Relationship (ECOSAR) analysis showed that the intermediates were lowly toxic during the PFOS degradation, manifesting a green process for PFOS removal. This study would provide more understandings for the persulfate activation process mediated by Fe-based catalysts for Perfluorinated alkyl substances (PFAS) elimination.

Catalytic electrodes' characterization study serving polluted water treatment: environmental healthcare and ecological risk assessment

Pesticide residues in the environment have irreparable effects on human health and other organisms. Hence, it is necessary to treat and degrade them from polluted water. In the current work, the electrochemical removal of the fenitrothion (FT), trifluralin (TF), and chlorothalonil (CT) pesticides were performed by catalytic electrode. The characteristics of SnO2-Sb2O3, PbO2, and Bi-PbO2 electrodes were described by FE-SEM and XRD. Dynamic electrochemical techniques including cyclic voltammetry, electrochemical impedance spectroscopy, accelerated life, and linear polarization were employed to investigate the electrochemical performance of fabricated electrodes. Moreover, evaluate the risk of toxic metals release from the catalytic electrode during treatment process was investigated. The maximum degradation efficiency of 99.8, 100, and 100% for FT, TF, and CT was found under the optimal condition of FT, TF, and CT concentration 15.0 mg L-1, pH 7.0, current density 7.0 mA cm-2, and electrolysis time of 120 min. The Bi-PbO2, PbO2, and SnO2-Sb2O3 electrodes revealed the oxygen evolution potential of 2.089, 1.983, 1.914 V, and the service lifetime of 82, 144, and 323 h, respectively. The results showed that after 5.0 h of electrolysis, none of the heavy metals such as Bi, Pb, Sb, Sn, and Ti were detected in the treated solution.

Bibliometric analysis and literature review of ultrasound-assisted degradation of organic pollutants

Ultrasound as a clean, efficient, and cheap technique gains special attention in wastewater treatment. Ultrasound alone or coupled with hybrid processes have been widely studied for the treatment of pollutants in wastewater. Thus, it is essential to conduct a review about the research development and trends on this emerging technique. This work presents a bibliometric analysis of the topic associated with multiple tools such as Bibliometrix package, CiteSpace, and VOSviewer. The literature sources from 2000 to 2021 were collected from Web of Science database, and the data of 1781 documents were selected for bibliometric analysis in respect to publication trends, subject categories, journals, authors, institutions, as well as countries. Detailed analysis of keywords in respect to co-occurrence network, keyword clusters, and citation bursts was conducted to reveal the research hotspot and future directions. The development of the topic can be divided into three stages, and the rapid development begins from 2014. The leading subject category is Chemistry Multidisciplinary, followed by Environmental Sciences, Engineering Chemical, Engineering Environmental, Chemistry Physical, and Acoustics, and there exists difference in the publications of different categories. Ultrasonics Sonochemistry is the most productive journal (14.75 %). China is the leading country (30.26 %), followed by Iran (15.67 %) and India (12.35 %). The top 3 authors are Parag Gogate, Oualid Hamdaoui, and Masoud Salavati-Niasari. There exists close cooperation between countries and researchers. Analysis of highly cited papers and keywords gives a better understanding of the topic. Ultrasound can be employed to assist various processes such as Fenton-like process, electrochemical process, and photocatalysis for degradation of emerging organic pollutants for wastewater treatment. Research topics in this field evolve from typical studies on ultrasonic assisted degradation to latest studies on hybrid processes including photocatalysis for pollutants degradation. Additionally, ultrasound-assisted synthesis of nanocomposite photocatalysts receives increasing attention. The potential research directions include sonochemistry in pollutant removal, hydrodynamic cavitation, ultrasound-assisted Fenton or persulfate processes, electrochemical oxidation, and photocatalytic process.

Mechanisms and degradation pathways of doxycycline hydrochloride by Fe3O4 nanoparticles anchored nitrogen-doped porous carbon microspheres activated peroxymonosulfate

Peroxymonosulfate (PMS) based advanced oxidation processes have gained widespread attention in refractory antibiotics treatment. In this study, Fe₃O₄ nanoparticles anchored nitrogen-doped porous carbon microspheres (Fe₃O₄/NCMS) were synthesized and applied to PMS heterogeneous activation for doxycycline hydrochloride (DOX-H) degradation. Benefitting from synergy effects of porous carbon structure, nitrogen doping, and fine dispersion of Fe₃O₄ nanoparticles, Fe₃O₄/NCMS showed excellent DOX-H degradation efficiency within 20 min via PMS activation. Further reaction mechanisms revealed that the reactive oxygen species including hydroxyl radicals (•OH) and singlet oxygen (¹O₂) played the dominant role for DOX-H degradation. Moreover, Fe(II)/Fe(III) redox cycle also participated in the radical generation, and nitrogen-doped carbonaceous structures served as the highly active centers for non-radical pathways. The possible degradation pathways and intermediate products accompanying DOX-H degradation were also analyzed in detail. This study provides key insights into the further development of heterogeneous metallic oxides-carbon catalysts for antibiotic-containing wastewater treatment.

Detection Techniques for Lead Ions in Water: A Review

Lead pollution has increasingly become the focus of environmental pollution, which is a great harm to the ecological environment and human health. Strict control of the emission of lead pollutants and accurate monitoring of lead are very important. The lead ion detection technologies are introduced here, including spectrophotometry, electrochemical method, atomic absorption spectrometry, and other detection methods, and the methods' applicability, the advantages, and disadvantages are discussed. The detection limits of voltammetry and atomic absorption spectrometry are as low as 0.1 μg/L, and those of atomic absorption spectrometry are as low as 2 μg/L. The detection limit of photometry is higher (0.01 mg/L), but this method can be achieved in most laboratories. The application of different extraction pretreatment technologies in lead ion detection is introduced. The new technologies develop at home and abroad, such as precious metal nanogold technology, paper microfluidic technology, fluorescence molecular probe technology, spectroscopy, and other emerging technologies in recent years, are reviewed, and the principle and application of various technologies are expounded.

Adsorption of methylene blue from textile industrial wastewater using activated carbon developed from Rumex abyssinicus plant

Methylene blue (MB) is abundantly found in textile industrial effluent which can cause severe health problems for public and environmental ecology. Therefore, this study aimed to remove MB from textile wastewater using the activated carbon developed from Rumex abyssinicus. The adsorbent was activated using chemical and thermal methods, and then it was characterized by SEM, FTIR, BET, XRD, and pH zero-point charge (pHpzc). The adsorption isotherm and kinetics were also investigated. The experimental design was composed of four factors at three levels (pH (3, 6, and 9), initial MB concentration (100, 150, and 200 mg/L), adsorbent dosage (20, 40, and 60 mg/100 mL), and contact time (20, 40, and 60 min)). The adsorption interaction was evaluated using response surface methodology. The characterization of a Rumex abyssinicus activated carbon was found to have multiple functional groups (FTIR), an amorphous structure (XRD), crack with ups and down morphology (SEM), pHpzc of 5.03 and a high BET-specific surface area of 2522 m²/g. The optimization of MB dye removal was carried out using the Response Surface methodology coupled with the Box Behnken approach. The maximum removal efficiency of 99.9% was recorded at optimum conditions of pH 9, MB concentration of 100 mg/L, the adsorbent dosage of 60 mg/100 mL, and contact time of 60 min. Among the three adsorption isotherm models, the Freundlich isotherm model was the best fit with an experimental value at R² 0.99 showing the adsorption process was heterogeneous and multilayer whereas the kinetics study revealed that pseudo-second-order at R² 0.88. Finally, this adsorption process is quite promising to be used at an industrial level.

Electrostatic deposition of TiO2 nanoparticles on porous wood veneer for improved membrane filtration performance and antifouling properties

Wood has been a promising water purifier material on account of its abundant natural transport channels, easy processing, and renewability, which is mainly focused on its utilization in growth direction for effective separation.Wood veneer manufacured from raw wood block has a reversed-tree pore structure, and possesses advantages of low cost, easy fabrication, material saving, and abundant sources. To realize its functionalization and practicable application for membrane separation, modification of wood veneer is prerequisite. Herein, thin wood veneer with disparate utilization direction of wood was developed to design filter membrane loading TiO₂ nanoparticles for treatment of dye wastewater. Wood veneer with reversed-tree transport pathways exhibits unique porous structure, and filtering direction and wood growth direction is almost orthogonal generated numerous sinuous channels. Thereout, sufficient area for loading TiO₂ nanoparticles and contacting pollutants as well as appropriate water transport pathways at significantly shrinking thickness of wood (the thickness of 0.2 mm) can be provide by these sinuous channels. TiO₂ nanoparticles was first modified by (3-Aminopropyl)triethoxysilane with high positive charge, and immobilized on negatively charged wood surface through atmospheric impregnation via strong electrostatic attractive interaction. Vast quantities of exposed TiO₂ nanoparticles on wood cell lumens significantly enhance the adsorption ability for dye contaminants, resulting in a high membrane separation performance. The flux of TiO₂/wood veneer membrane can achieve high level of 636.94 L/(m²h) with considerable methylene blue removal of 99.9% at 0.01 MPa. Meanwhile, it shows good cycling stability as well as decent flexibility and excellent mechanical strength. Moreover, the designed membrane with photocatalytic function of TiO₂ also displays impressive decontaminated and recycling ability. The flux can recover its pre-recession level after 10 h light irradiation. The designed TiO₂/wood veneer with simple preparation process and excellent water treatment capacity exhibits promising results for practical wastewater treatment.

The application of a new recyclable photocatalyst γ-Fe2O3@SiO2@ZIF8-Ag in the photocatalytic degradation of amoxicillin in aqueous solutions

This pilot study synthesized the γ-Fe₂O₃@SiO₂@ZIF8-Ag nanocomposites via the hydrothermal method to study its potential use in amoxicillin degradation as a novel photocatalyst in aqueous solutions under visible light radiation. Various diagnostic methods were used to determine the morphology and functional structure of the photocatalyst, and the results confirmed its proper formation. Complete degradation of AMX was obtained at a pH of 5, catalyst dosage of 0.4 g/L, AMX concentration of 10 mg/L, and reaction time of 60 min. The efficiency of the degradation was diminished when anions were present in the reaction medium, and the order of their effect was SO₄^2- < Cl^- < NO₃^- < HCO₃^-. Biodegradability (BOD₅/COD ratio) increased from 0.20 to 0.68 after 120 min of photocatalytic treatment, with a COD removal of 87.54% and a TOC removal of 74.88%. Through the experimental trapping of electrons, we found the production of reactive species, such as hydroxyl radical (•OH), superoxide (O₂^•-), and holes (h⁺), in the photocatalysis reactor and that •OH was the predominant species in AMX photodegradation. Comparative experiments emphasized that the oxidation process occurs with the adsorption of pollutants on the surface of the catalyst, and the photocatalyst has the potential to be activated by various light sources, including visible light, UV light, and sunlight, with an AMX decomposition above 88%. The synthesized particles can be recovered after five consecutive cycles with minimal reduction in the degradation rate (< 4%). γ-Fe₂O₃@SiO₂@ZIF8-Ag can be considered a promising photocatalyst for use in AMX degradation due to its recyclability, easier activation by different light sources, and excellent mineralization.

Removal of the Pigment Congo Red from Synthetic Wastewater with a Novel and Inexpensive Adsorbent Generated from Powdered Foeniculum Vulgare Seeds

In this research, powdered Foeniculum vulgare seed (FVSP) was treated separately with H2C2O4, ZnCl2, and a mixture of ZnCl2-CuS. The characteristics of the treated and untreated FVSP samples, as well as their abilities to eliminate Congo red (CR) from solutions, were investigated. The influences of the empirical circumstances on CR adsorption by the ideal adsorbent were studied. The thermodynamic, isothermal, and dynamic constants of this adsorption were also inspected. The ideal adsorbent was found to be the FVSP sample treated with a ZnCl2-CuS mixture, which eliminated 96.80% of the CR dye. The empirical outcomes proved that this adsorption was significantly affected by the empirical circumstances, and the second-order dynamic model as well as the Langmuir isotherm model fit the empirical data better than the first-order model and the Freundlich model. The values of Ea (15.3 kJ/mol) and ∆Ho (32.767 kJ/mol ≤ ∆Ho ≤ 35.495 kJ/mol) evidence that CR anions were endothermally adsorbed on Zn/Cu-FVSP via the ionic exchange mechanism. The superior Qmax values (434.78, 625.00, 833.33 mg/g), along with the cheapness and stability of the adsorbent used in this work, are evidence to confirm that this adsorbent will receive special interest in the field of contaminated water purification.

Waste toner-derived porous iron oxide pigments with enhanced catalytic degradation property

'Wealth from Waste' is an emerging concept, since it leads an effective waste treatment and waste recyclability. On the other hand, cost effective production iron oxide (IO) nanomaterials is still needed to develop, owing to their wide applications. Herein, we proposed a simple direct calcination method to prepare porous IO (Fe₃O₄ and Fe₂O₃) nanomaterials from waste toner powder. Characterization techniques reveal that a structural change happened from Fe₃O₄ to γ-Fe₂O₃ and γ-Fe₂O₃ to α-Fe₂O₃ at the calcination temperature of 500 °C and 700 °C respectively. Consequently, optical (band gap) and magnetic parameters of IO samples were significantly varied. The pigment characteristics of the IO samples were evaluated using Commission Internationale de l'Eclairage (CIE) analysis. IO900 sample has shown good brown-red coloration (L* = 43.11, a* = 13.26 and b* = 5.69) and it also exhibited good stability in acidic and basic conditions. Practical applicability of IO pigments were also tested by mixing with plaster of paris (PP) powder. Further, porous IO samples were also used as catalysts in the reductive degradation of methyl orange (MO) dye in presence of excess sodium borohydride (NaBH₄). IO, prepared at 900 °C exhibited ∼99.9% reduction efficiency within 40 min. Recycling experiments indicated that IO900 possess good stability up to seven cycles. The present porous IO samples will become potential in pigment and environmental remediation.

Wastewater treatment with nanomaterials for the future: A state-of-the-art review

Aquatic and terrestrial ecosystems are both threatened by toxic wastewater. The unique properties of nanomaterials are currently being studied thoroughly for treating sewage. Nanomaterials also have the advantage of being capable of removing organic matter, fungi, and viruses from wastewater. Advanced oxidation processes are used in nanomaterials to treat wastewater. Additionally, nanomaterials have a large effective area of contact due to their tiny dimensions. The adsorption and reactivity of nanomaterials are strong. Wastewater treatment would benefit from the development of nanomaterial technology. Second, the paper provides a comprehensive analysis of the unique characteristics of nanomaterials in wastewater treatment, their proper use, and their prospects. In addition to focusing on their economic feasibility, since limited forms of nanomaterials have been manufactured, it is also necessary to consider their feasibility in terms of their technical results. According to this study, the significant adsorption area, excellent chemical reaction, and electrical conductivity of nanoparticles (NPs) contribute to the successful treatment of wastewater.

Formation of Recalcitrant Compounds during Anaerobic Digestion of Thermally Pre-Treated Sludge: A Critical Macromolecular and Structural Study

Thermal hydrolysis, when used as pre-treatment, enhances the anaerobic digestion of sewage sludge; moreover, due to the high temperature normally applied, undesirable recalcitrant compounds via Maillard reactions may also be formed. However, although the appearance of these recalcitrant compounds is widely reported, more information on the formation, structure, and fate of these compounds is still needed. This study was focused on understanding the amount and whereabouts of such compounds during the anaerobic digestion process with thermal pre-treatment in soluble and total phase and advance in its structural identification by analyzing their infrared (IR) spectra. It was found that, even with the improved methane production and COD degradation, at 165 °C for 30 min, humic-like compounds are formed which could not be degraded at the anaerobic digestion step. These compounds account for 25% of the original sludge. Infrared spectroscopy proved to be a powerful technique, permitting their differentiation from the natural humic-like compounds. This research provides new information about the structure of melanoidins at every stage of the thermal hydrolysis pre-treatment and how they contribute to the dissolved organic nitrogen.

Synthesis of biochar-CoFe2O4 nanocomposite for adsorption of methylparaben from wastewater under full factorial experimental design

The presence of endocrine-disrupting chemicals in municipal wastewater has emerged as a threat to human health and the environment. Therefore, this study aimed to develop biochar-cobalt ferrite (BCF) nanocomposite for the removal of methylparaben from water under the full factorial experimental design of 4 factors with 3 levels (3⁴). The biochar-CoFe₂O₄ nanocomposite was developed by co-precipitation method from cobalt ferrite and biochar of Eucalyptus tree bark. Adsorbent surface morphology and functional and elemental composition were carried out by scanning electron microscopy (SEM), Fourier transform infrared (FTIR) spectroscopy, and energy-dispersive X-ray spectroscopy (EDS) techniques which showed the presence of cracks with a rough surface, reasonable surface chemical composition, and many chemical functional groups, respectively. The experimental and predicted adsorption efficiencies ranged from 25.3 to 85.6% and 21.8 to 80.3%, respectively. The maximum adsorption performance (85.6%) reduced the methylparaben concentration from 27.5 to 4.0 mg/L at the optimum condition of adsorbent dose of 55 mg/100 mL, pH 6, contact time 90 min, and the initial methylparaben concentration of 27.5 mg/L. However, the adsorbent dose was the most influential main factor whereas the least influential was the interaction between solution pH and contact time under the regression model. The model also showed that 69% methylparaben removal was described by the regression model. The experimental data best fitted with the Freundlich model indicate multilayer adsorption which is the implication of physisorption. The sorption mechanism is attributed to Vander Waals forces, H-bonding, and dipole interaction. This BCF nanocomposite adsorbent appears to be promising for the removal of methylparaben from wastewater, but a further optimization process is essential to boost the treatment performance.

Response surface modeling of ceftriaxone removal from hospital wastewater

In recent decades, an emerging concern of widespread antimicrobial resistance has been raised due to the existence of pharmaceutical samples such as antibiotics in an aqueous medium. Herein, antibiotic ceftriaxone (CTX) removal from hospital wastewater employing a hybrid process of electrocoagulation (EC) and adsorption (AD) was investigated. The response surface methodology (RSM) was employed to study the influences of main operating variables, including initial CTX concentration, pH, current density, reaction time, and chitosan dosage, on the removal efficiency of the treatment process. Under the optimum condition of the employed EC/AD hybrid treatment process, where initial CTX concentration, pH solution, the current density, adsorbent dosage, and reaction time were set at 20.0 mg L^-1, 7.5, 6.0 mA cm^-2, 0.75 g L^-1, and 12.5 min, respectively, the removal efficiency of 100% was achieved. Analysis of variance (ANOVA) confirmed that the developed quadratic treatment model is highly significant. The applied EC/AD hybrid treatment process revealed the electrical energy consumption of 0.84 kWh m^-3 and 0.2168 kWh (g Al)^-1 per cubic meter of hospital wastewater and gram of consumed aluminum electrode, respectively. The second-order kinetic model with R² of 0.9514 and the Langmuir isotherm model with R² of 0.973 best fit the developed EC/AD hybrid treatment process, and q_m was found to be 111.1 mg g^-1. The obtained experimental results confirmed that the CTX concentration of the hospital wastewater was reduced to zero after applying the EC/AD hybrid process.

An approach to removing COD and BOD based on polycarbonate mixed matrix membranes that contain hydrous manganese oxide and silver nanoparticles: A novel application of artificial neural network based simulation in MATLAB

This study aimed to determine the efficacy of novel ultrafiltration and mixed matrix membrane (MMM) composed of hydrous manganese oxide (HMO) and silver nanoparticles (Ag-NPs) for the removal of biological oxygen demand (BOD) and chemical oxygen demand (COD). In the polycarbonate (PC) MMM, the weight percent of HMO and Ag-NP has been increased from 5% to 10%. A neural network (ANN) was used in this study to compare PC-HMO and Ag-NP. MMM was evaluated in combination with HMO and Ag-NP loadings in order to assess their effects on pure water flux, mean pore size, porosity, and efficacy in removing BOD and COD. HMO and Ag-NPs can decrease membrane porosity in the casting solution while increasing mean pore size. According to the study's findings, the artificial neural network model appears to be highly appropriate for predicting the removal of BOD and COD. To develop a successful model, a suitable input dataset was selected, which consisted of BOD and COD. An ideal model architecture for MMM was proposed based on an optimal number of hidden layers (2 layers) and neurons (5-8 neurons). Experiments and predicted data show a strong correlation between the developed models. BOD was predicted with an excellent R2 and a low root mean square error (RMSE) of 0.99 and 0.05%, respectively, while COD was predicted with an excellent R2 and a low RMSE of 0.99 and 0.09%, respectively. Based on the results, Ag-NP was found to be an excellent candidate for the preparation of MMMs as well as convenient for the removal of BOD and COD from polluted water sources.

Ultrasound-enhanced catalytic degradation of simulated dye wastewater using waste printed circuit boards: catalytic performance and artificial neuron network-based simulation

Recent developments of heterogeneous advanced oxidation for refractory organic contaminants and catalysts made of solid waste have attracted much attention. In this work, waste printed circuit board (wPCB) was used for catalytic degradation of simulated textile wastewater enhanced by ultrasound. Catalytic degradation of rhodamine B (RhB) and methylene blue (MB) was conducted in the presence of H₂O₂. Effect of ultrasound, wPCB, H₂O₂, pH, and dye concentration was investigated by single factor experiments. The growing catalytic efficiency was determined by ultrasound. The removal efficiency of MB and RhB are influenced by wPCB, H₂O₂, pH, and dye concentration. Degradation efficiency is accelerated with increasing wPCB dosage and H₂O₂ and decreasing dye concentration. Effective degradation of MB and RhB is obtained under broader pH region, attractively at neutral pH. Under optimal conditions, MB removal reaches 98.83% at 90 min while RhB removal reaches 99.57% at 80 min. Hydroxyl radicals play an important role in catalytic process. Tentative mechanism for catalytic degradation of MB and RhB are discussed based on multiple characterizations. Superior reusability of wPCB proves that wPCB is highly durable catalyst. Due to low cost and high efficiency, wPCB is attractive as effective catalyst for treatment of organic wastewater. Artificial neuron network-based (ANN) simulation, as a widely used artificial intelligence algorithm, was one of preferred methods for the wastewater treatment due to its unique properties in solving complex processes. An ANN model was designed for the prediction of the performance of ultrasound-enhanced catalytic degradation with a high R value (0.99).

BCOFGs loaded with nano-FexSy for the catalytic degradation of QNC: Contribution and mechanism of OFGs for reductive iron regeneration

Biochar currently served as the support for dispersed metal nanoparticles and cooperated with pyrite to generate more reactive radicals in organic pollution degradation system. But the mechanism of interaction between biochar and pyrite has not been elucidated. In this paper, biochar with oxygen-containing functional groups (OFGs) served as a stable dispersant to prepare nano-Fe_xS_y loaded biochar materials (BC_OFGs@nano-Fe_xS_y). BC_OFGs coordinated with nano-Fe_xS_y to overcome its drawbacks, boosting QNC removal efficiency from 28.64% to 100%. The XPS and the linear sweep voltammetry (LSV) results revealed higher Fe(II) content and higher electron transfer rate on used BC_OFGs@nano-Fe_xS_y, further validating that hydroxyl functional groups on biochar surface provided electrons to Fe(III) to achieve efficient Fe(II)/Fe(III) cycling. Based on comparative experiments and studies on the roles of iron, S(II) species and OFGs, we clearly revealed that OFGs on biochar materials surface coordinated with nano-Fe_xS_y to catalyze the degradation of QNC. The degradation efficiency of BC_OFGs@nano-Fe_xS_y for QNC was still as high as 91.39% after five cycles, providing full demonstrations that OFGs and S(II) as the abundant electron donor coordinated with Fe species for QNC catalytic degradation and further enhanced the catalytic performance and stability of nano-Fe_xS_y.

Waste coal cinder catalyst enhanced electrocatalytic oxidation and persulfate advanced oxidation for the degradation of sulfadiazine

Waste coal cinder, a kind of waste cinder discharged from coal combustion of thermal power plants, industrial and civil boilers, and other equipment, was rich in metal oxides with catalytic activity. In this work, waste coal cinder was used to enhance electrochemical coupling peroxymonosulfate (PMS) advanced oxidation degradation of sulfadiazine (SD). The surface morphology, elemental composition, and electrocatalytic activity of waste coal cinder were characterized by various characterization instruments. The results show that compared with simple electrocatalytic oxidation, electrocatalytic oxidation + waste coal cinder and electrocatalytic coupled persulfate oxidation, electrocatalytic oxidation + PMS advanced oxidation + waste coal cinder has the largest removal efficiency (99.95%) and mineralization rates (90.16%) of SD in 90 min, indicating that the introduction of waste coal cinder greatly increases the degradation efficiency. •OH and SO₄^-• were detected during the process of degradation. The optimal degradation process parameters were explored through different voltage, pH, plate spacing, aeration flow rate, potassium peroxymonosulfate sulfate complex salt dose, and Na₂SO₄ dosage. Cycling experiments show waste coal cinder has good structural stability. Through the analysis of triple quadrupole liquid chromatography-mass spectrometry (LC-MS), we put forward three possible ways of SD degradation. This research will provide a novel vision for water treatment.

Controlled carbonization of microplastics loaded nano zero-valent iron for catalytic degradation of tetracycline

Nano zero-valent iron loaded porous carbon derived from microplastics was designed as heterogeneous catalyst for degradation of persistent organic pollutants. Controlled carbonization of microplastics with molten salt was conducted to tune the morphology of carbon product. Controlled carbonization induces higher carbon yield (from 17.73% to 52.24%) and larger surface area (from 403.72 m²/g to 601.82 m²/g). The catalyst (Fe/MMPC) was characterized by Raman, Fourier transform infrared spectroscopy, X-ray diffraction, X-ray photoelectron spectroscopy, and scanning electron microscope. Loading nano zero-valent iron onto porous carbon are verified in the catalyst. The process factors including Fe/MMPC dosage, H₂O₂, pH, anions, and temperature were studied to estimate the catalytic performance. Tetracycline degradation (81.8% within 10 min) is effectively obtained in the Fe/MMPC and H₂O₂ system. The apparent rate constant is 0.1311-0.2999 min^-1 under different temperature, and the activation energy of catalytic process is 22 kJ/mol. Pollutants including rhodamine B, p-nitrophenol, and butylxanthate are efficiently degraded in the catalytic system. The predominant species of catalytic reactions are hydroxyl radicals, which are mainly produced from H₂O₂ activation enhanced by zero-valent iron in Fe/MMPC. This work offers an innovative strategy for microplastic management and wastewater treatment.