Method for the fast determination of bromate, nitrate and nitrite by ultra performance liquid chromatography–mass spectrometry and their monitoring in Saudi Arabian drinking water with chemometric data treatment

Recent advances in electrochemical approaches for detection of nitrite in food samples

Nitrite is a common ingredient in the industry and agriculture; it is everywhere, like water, food, and surroundings. Recently, several approaches have been developed to measure the nitrite levels. So, this review was presented as a summary of many approaches utilized to detect the nitrite. Furthermore, the types of information that may be acquired using these methodologies, including optic and electrical signals, were discussed. In electrical signal methods, electrochemical sensors are usually developed using different materials, including carbon, polymers, oxides, and hydroxides. At the same time, optic signals receiving techniques involve utilizing fluorescence chromatography, absorption, and spectrometry instruments. Furthermore, these methodologies' benefits, drawbacks, and restrictions are examined. Lastly, due to the efficiency and fast means of electrochemical detectors, it was suggested that they can be used for detecting nitrite in food safety. Futuristic advancements in the techniques used for nitrite determination are subsequently outlined.

A fungal hyphae-derived biomass carbon for magnetic solid-phase extraction of the organochlorine pesticides in water samples, tea beverages, and Chinese traditional medicines before gas chromatography-tandem mass spectrometry determination

A magnetic biochar nanomaterial derived from fungal hyphae was introduced into the sample preparation field. The magnetic fungal hyphae-derived biomass carbon (MFHBC) could be produced by a controllable hydrothermal method. In order to obtain the best sorbent for magnetic solid-phase extraction (MSPE), the reaction conditions containing temperature, time and the consumption of fungal hyphae were investigated. A series of MFHBC materials were characterized by vibrating sample magnetometers, X-ray photoelectron spectroscopy, Fourier transform infrared spectroscopy, and transmission electron microscopy. A material with a satisfactory saturation magnetization (21.58 emu g-1) and largest surface area (88.06 m2 g-1) was selected as the sorbent to extract ten typical organochlorine pesticides (OCPs). The extraction conditions were optimized as 20 mL of sample solution with 70 mg of sorbent and 2.0 g of NaCl oscillated at 50 °C for 5.0 min. And the optimum desorption was performed by oscillating sorbent in 1.0 mL acetonitrile for 5.0 min. Then, the MFHBC-based MSPE-GC-MS/MS methods were established for different samples including water samples, tea beverages, and Chinese traditional medicines. The linearities were 10-2500 ng L-1 or 100-25,000 ng kg-1, and the limits of detection were 0.3-13.9 ng L-1 for water sample, 0.1-9.7 ng L-1 for tea beverage samples, 0.1-21.4 ng L-1 for Shenqi Fuzheng injection samples, and 7.2-278.3 ng kg-1 for Astragali Radix decoction pieces. Except for satisfactory repeatability (RSDs ≤13.8%) in intra-day and inter-day tests (n = 3), the reproducibility (RSDs ≤13.5%, n = 3) of MFHBC was acceptable. The methods were applied in the determination of OCPs from above real samples, with the recoveries of 80.5-117.2% and the RSDs (n = 3) <8.9%. The methods were suitable in the sensitive determination of OCPs from simple to complex matrix samples.

Evaluation of some anions in groundwater in Riyadh, Saudi Arabia, and human health risk assessment of nitrate and fluoride

Groundwater is a vital source of water for human and agricultural use in many parts of the world. The purpose of this research was to establish the quality of groundwater in Riyadh, Saudi Arabia, as well as the human health concerns associated with it. We collected and examined groundwater samples for pH, EC, TDS, CaCO3, fluoride (F-), chloride (Cl-), sulfate (SO42-), and nitrate (NO3-). The ion chromatography conductometric detection method was constructed to determine fluoride, chloride, sulfate, and nitrate in groundwater. The suggested method worked well for the anions that were being studied; it had a high coefficient of determination (r2 > 0.998) and average recoveries for all analytes that were between 97.5% and 99.0%, with a range of error of 0.77 to 2.37%. Fluoride concentrations were detected between 0.001 and 0.14 mg/L, which are within the acceptable limit by several organizations. Chloride was measured in the range of 17.1 to 966.5 mg/L, with some samples above the limits. The influence on sulfate ranged from 2.0 to 1136.0 mg/L, with several samples exceeding the limits. In contrast, with nitrate levels ranging from 1.4 to 5.0 mg/L, the majority of the samples fall within the acceptable range. The overall intake of fluoride, chloride, sulfate, and nitrate is 0.00605, 138.911, 65.515, and 1.19, respectively, which is lower than the recommended daily consumption except for chloride. The groundwater sample contains fluoride and nitrate with HQ values less than one: 0.000064-0.0641 and 0.033654-0.120192. Humans in Riyadh, Saudi Arabia, do not pose a health risk when digesting or absorbing groundwater fluoride or nitrate.

Integration of Ultrathin Bubble Walls and Electrochemistry: Innovation in Microsensing for Forensic Nitrite Detection and Microscale Metallic Film Deposition

We present a strategy for electrochemical measurements using a durable minute bubble wall with a thickness of 27 μm (D = 1.8 cm) as an innovative electrochemical medium. The composition, thickness, and volume of the tiny bubble film were investigated and estimated using the spectroscopic method and the Beer-Lambert law. A carbon microelectrode (D = 10 μm) was then employed as the working electrode, inserted through the bubble wall to function as the solution interface. First, the potential of this method for microelectrodeposition of metallic Ag and Pd films in a tiny bubble was investigated. Interestingly, microscopic images of the deposited film clearly demonstrated that the bubble thickness determines and confines the electrochemical deposition zone. In other words, innovative template-free microelectrodeposition was achieved. In the second phase of our work, microelectroanalysis of trace levels of nitrite ions was performed within the bubble wall and on a foam-covered hand, between the fingers directly, with a low limit of detection of 28 μM. This technique holds significance in criminal investigations, as the presence of NO2- ions on the hand indicates the potential presence of gunshot residue and aids in identifying suspects. In comparison to current methods, this approach is rapid, simple, cost-effective, and amenable to on-site applications, eliminating the need for sample treatment. Ultimately, the utilization of a bubble wall as a novel electrochemical microreactor can open new ways in microelectrochemical analysis, presenting novel opportunities and applications in the field of electrochemical sensors.

Copper Nanoparticles Confined in a Silica Nanochannel Film for the Electrochemical Detection of Nitrate Ions in Water Samples

The nitrate ion (NO3-) is a typical pollutant in environmental samples, posing a threat to the aquatic ecosystem and human health. Therefore, rapid and accurate detection of NO3- is crucial for both the aquatic sciences and government regulations. Here we report the fabrication of an amino-functionalized, vertically ordered mesoporous silica film (NH2-VMSF) confining localized copper nanoparticles (CuNPs) for the electrochemical detection of NO3-. NH2-VMSF-carrying amino groups possess an ordered perpendicular nanochannel structure and ultrasmall nanopores, enabling the confined growth of CuNPs through the electrodeposition method. The resulting CuNPs/NH2-VMSF-modified indium tin oxide (ITO) electrode (CuNPs/NH2-VMSF/ITO) combines the electrocatalytic reduction ability of CuNPs and the electrostatic attraction capacity of NH2-VMSF towards NO3-. Thus, it is a rapid and sensitive electrochemical method for the determination of NO3- with a wide linear detection range of 5.0-1000 μM and a low detection limit of 2.3 μM. Direct electrochemical detection of NO3- in water samples (tap water, lake water, seawater, and rainwater) with acceptable recoveries ranging from 97.8% to 109% was performed, demonstrating that the proposed CuNPs/NH2-VMSF/ITO sensor has excellent reproducibility, regeneration, and anti-interference abilities.

Highly sensitive and ratiometric detection of nitrite in food based on upconversion-carbon dots nanosensor

Nitrite (NO₂^-) is extensively found in the daily dietary environment. However, consuming too much NO₂^- can pose serious health risks. Thus, we designed a NO₂^--activated ratiometric upconversion luminescence (UCL) nanosensor which could realize NO₂^- detection via the inner filter effect (IFE) between NO₂^--sensitive carbon dots (CDs) and upconversion nanoparticles (UCNPs). Due to the exceptional optical properties of UCNPs and the remarkable selectivity of CDs, the UCL nanosensor exhibited a good response to NO₂^-. By taking advantage of NIR excitation and ratiometric detection signal, the UCL nanosensor could eliminate the autofluorescence thereby increasing the detection accuracy effectively. Additionally, the UCL nanosensor proved successful in detecting NO₂^- quantitatively in actual samples. The UCL nanosensor provides a simple as well as sensitive sensing strategy for NO₂^- detection and analysis, which is anticipated to extend the utilization of upconversion detection in food safety.

An investigation on glutathione derived from spinach and red cabbage leaves and their effects of adding to meat patties

Plants that produce leaves have been cultivated by humans for thousands of years because of the benefits they provide in terms of food and other necessities. Because of their high nutritional value and key phyto-components like glutathione, Leaf producing vegetables (LPVs) are being studied for their potential uses and health benefits. As a result, the focus of this study was using efficient methods for isolating and identifying glutathione from spinach and red cabbage. Glutathione was extracted using three extraction solvents: water (100%), ethanol (100%), and a combination of ethanol and water (30% and 70%, respectively) by volume (v/v), while separation was accomplished using ultrafiltration equipment. In our investigation, the best extraction solvent was a mixture of ethanol and water at a ratio of 30:70% (v/v), which extracted 951 µg/g glutathione. The antioxidant activity of plant leaf extract was measured using DPPH, with butylated hydroxytoluene serving as a comparative standard. Identification and characterization of glutathione from plant leaf extracts were revealed by thin-layer chromatography (TLC), ultraviolet-visible (UV-Vis) spectrophotometry studies, Fourier transform infrared (FTIR) spectroscopy, and high-performance liquid chromatography (HPLC). In addition, the physical and chemical properties (pH, water holding capacity, extracted liquid volume, peroxide value, free fatty acids, and thiobarbituric acid) of meat patties prepared with three different concentrations of determined glutathione were tested for susceptibility to preservation during 10 days of refrigeration at 4 ± 1 °C. The findings of the current study provide vast prospects for subsequent research to researchers and scientists that the glutathione obtained from leaf extract has no toxicity that might be applied to developed functional foods and other food formulations. Because foods containing plant-derived glutathione improve health, biological function, and food spoilage. It may be utilized as high-quality antioxidants that are safe and non-toxic. Furthermore, glutathione preserves food quality and prevents oxidation.

MXene-based aptasensor for the detection of aflatoxin in food and agricultural products

The detection of toxins that contaminate food needs highly sensitive and selective techniques to prevent substantial monitory loss. In this regard, various nanostructured material-enabled biosensors, have recently been developed to improve the detection of food toxins among them aflatoxin is the prevalent one. The biosensor-based detection of aflatoxin is quick, cheaper, and needs less skilled personnel, therefore overcoming the shortcomings of conventional techniques such as LC/MS-MS, HPLC, and ELISA assays. 2D MXenes manifest as an efficient material for biosensing due to their desirable biocompatibility, magnificent mechanical strength, easiness of surface functionalization, and tuneable optical and electronic features. Contrary to this, aptamers as biorecognition elements (BREs) possess high selectivity, sensitivity, and ease of synthesis when compared to conventional BREs. In this review, we explored the most cutting-edge aptamer-based MXene-enabled biosensing technologies for the detection of the most poisonous mycotoxins (i.e., Aflatoxins) in food and environmental matrices. The discussion begins with the synthesis processes and surface functionalization/modification of MXenes. Computational approaches for designing aptasensors and advanced data analysis based on artificial intelligence and machine learning with special emphasis over Internet-of-Thing integrated biosensing devices has been presented. Besides, the advantages of aptasensors over conventional methods along with their limitations have been briefed. Their benefits, drawbacks, and future potential are discussed concerning their analytical performance, utility, and on-site adaptability. Additionally, next-generation MXene-enabled biosensing technologies that provide end users with simple handling and improved sensitivity and selectivity have been emphasized. Owing to massive applicability, economic/commercial potential of MXene in current and future perspective have been highlighted. Finally, the existing difficulties are scrutinized and a roadmap for developing sophisticated biosensing technologies to detect toxins in various samples in the future is projected.

Accurate quantification, naked eyes detection and bioimaging of nitrite using a colorimetric and near-infrared fluorescent probe in food samples and Escherichia coli

Nitrite (NO₂^-) is an inorganic contaminant that exists widely in the environment including water and food products, excessive amounts of NO₂^- would threaten humans and aquatic life. Developing a rapid and convenient sensing method for NO₂^- remains a great challenge. Herein, a colorimetric and near-infrared fluorescent probe (TBM) was synthesized and applied for sensitively and selectively detecting NO₂^- in water, food samples and Escherichia coli (E. coli). With the addition of NO₂^-, the probe TBM solution has a distinct visual color changed from red to colorless and fluorescence intensity at 620 nm quickly decreased. The probe TBM could detect NO₂^- quantitatively with a detection limit of 85 nM based on a 3σ/slope. Under optimum conditions, TBM has been successfully used to detect NO₂^- in real-world environmental and dietary samples, with positive results. Besides, paper strips loaded with TBM have been used to visually determine NO₂^- levels. Most importantly, TBM has also been proven to be able to discriminate from different concentrations of NO₂^- in E. coli by fluorescence imaging. In summary, the probe TBM was successfully developed for the accurate quantification, naked eyes detection and bioimaging of NO₂^- in water, food samples and E. coli, which provides a useful tool to better guarantee the quality and safety of daily life and food industry.

Determination of the geographic origin of 52 honey samples based on the assessment of anionic content profiling with a new algorithm using monolithic column-based micellar nano-liquid chromatography

In the present study, a new micellar nano LC-UV was, for the first time, reported for the separation and determination of five anions (chloride, nitrite, bromide, sulfate and nitrate) in 52 honey samples. Based on this approach, a graphene oxide-based monolithic column was prepared and applied for the samples. Various amounts of hexadecyltrimethyl-ammonium bromide (HTAB) in the mobile phase were used in order to optimize the separation conditions. The baseline separation was achieved using mobile phase with 25/75% (v/v) ACN/10 mM phosphate buffer at pH 3.4, while the amount of HTAB was optimized as 0.22 mM in the mobile phase. The whole method was validated and it leads to high sensitivity. The LOD values were found in the range of 0.02-0.22 µg/kg, while LOQ values were found in the range of 0.06-0.18 µg/kg. The method allowed to achieve sensitivity analyses of anionic content in 52 honey samples. All data were evaluated using a new algorithm for geographic origin discrimination. K-nearest neighbor algorithm (K-NN), cubic support vector classifier (K-DVS), and K-Mean cluster analysis were used for geographic origin discrimination of honeys. The accuracy of the whole model was calculated as 94.4% with the K-DVS method. The samples from five provinces were classified 100% correctly, while two of them were classified with one misclassification, with an accuracy of 89.9% and 83.3%, respectively. PRACTICAL APPLICATION: The new platforms and advanced technologies are crucial for advanced food analysis. In this article, a novel methodology was attempted for the determination of geographic origin of 52 honey samples. In this sense, micellar nano LC technique with a homemade monolithic nano-column was, for the first time, applied for the anion analysis using a new algorithm.

Dual determination of nitrite and iron by a single greener sequential injection spectrophotometric system employing a simple single aqueous extract from Areca catechu Linn. serving as a natural reagent

Dual determination of nitrite and iron was proposed by using a single greener sequential injection (SI) spectrophotometric system employing a simple single aqueous extract from Areca catechu Linn. The extract served as a natural reagent to replace N-(1-naphthyl)ethylenediamine (NED) of the Griess reagent with nitrite and 1,10-phenanthroline with iron. The color products possessed analytical wavelengths at 430 and 560 nm, respectively. Conditions for the SI procedure were optimized using a univariate experimental design. Calibration ranges were up to 5.0 mg L-1 and 10.0 mg L-1 with limits of detection (LODs) of 0.04 mg L-1 and 0.05 mg L-1 for nitrite and iron(iii), respectively, and relative standard deviations (RSDs) being less than 3%. Recoveries of spiked standard nitrite and iron(iii) at 0.3 mg L-1 and 0.5 mg L-1 in water samples were 88 to 104% and 84 to 109%, respectively. The developed method successfully achieved dual determination of nitrite and total iron agreeing at a 95% confidence level with the reference methods of the conventional Griess assay and flame atomic absorption spectrometry (FAAS), respectively. The proposed method utilized locally available material from plants and serves the UN-SDGs.

Fluorine and nitrogen co-doped near-infrared carbon dots for fluorescence "on-off-on" determination of nitrite

A fluorescence "on-off-on" strategy was established for the determination of nitrite in aqueous solution based on fluorine and nitrogen co-doped near-infrared carbon dots (NIR-CDs). NIR-CDs were prepared via one-step hydrothermal method by using N-(4-aminophenyl)-acetamide and 4,5-difluorobenzene-1,2-diamine as precursors. The photoluminescence quantum yield of NIR-CDs reaches to 17.4%, and the optimal emission peak of NIR-CDs is 675 nm under excitation of 530 nm. The Stokes shift of NIR-CDs (145 nm) is higher than that of some CDs with longer emission wavelengths. The red bathophenanthroline disulfonic acid (BPS)-Fe²⁺ complex can quench the fluorescence of NIR-CDs via inner filter effect and static quench modes. Nitrite can oxidize Fe²⁺ to produce Fe³⁺ in acidic environment, resulting in not only the formation of colorless and unstable BPS-Fe³⁺ complex but also the fluorescence recovery of NIR-CDs. This fluorescence "on-off-on" phenomenon also comes with the color variation of the mixture, resulting in both the fluorescence and the visual determination of nitrite. Under optimal conditions, this assay exhibits a good linear range from 1 to 50 μM and a low detection limit of 0.056 μM for nitrite determination. The method showed good applicability for nitrite determination in soil extract, human urine, and water samples with acceptable results. A convenient fluorescence "on-off-on" strategy for nitrite detection based on fluorine and nitrogen co-doped near-infrared carbon dots (NIR-CDs) and bathophenanthroline disulfonic acid (BPS)-Fe²⁺ complex was innovatively established. This probe showed a low detection limit of 0.056 μM for nitrite in authentic samples, which offered a new sight for fluorescent and visual detection of nitrite in environmental protection and human health areas.

The facile synthesis of nitrogen and sulfur co-doped carbon dots for developing a powerful "on-off-on" fluorescence probe to detect glutathione in vegetables

To determine the glutathione (GSH) content in vegetables, an "on-off-on" fluorescence probe was developed by a synthesis of nitrogen and sulfur co-doped carbon dots (N,S-CDs) using the microwave pyrolysis considering citric acid and L-cysteine as precursors. The fluorescence of N,S-CDs was quenched by adding Cu²⁺ at a concentration of 20-200 μmol/L due to the inner filter effect. The quenched fluorescence of N,S-CDs@Cu²⁺ system was recovered by adding the GSH at a concentration of 10-150 μmol/L due to the sulfhydryl-metal compound mechanism. By observing the GSH concentrations measured by our N,S-CDs@Cu²⁺ system vs. a traditional fluorescent chelating method, the two measurements provided the GSH data with a good consistence by showing the RSD range of 1.86%-2.27%. This indicates the validation and novelty of our N,S-CDs@Cu²⁺ system as being a powerful fluorescent probe for effectively and efficiently determining the GSH in vegetables.

A novel highly specific colorimetric fluorescent probe for the detection of nitrite in aqueous solution

Developing an effective method for the detection of nitrite (NO₂ ^- ions) in natural environment especially environmental waters and soils is very necessary, because it will cause serious damage to human health once excess NO₂ ^- ions enters the human body. Herein, a new colorimetric fluorescent probe NB-NO₂ ^- for determining NO₂ ^- ions was designed, and it possesses good water-solubility and pleasurable selectivity over others common ions for NO₂ ^- ions. The addition of NO₂ ^- ions changed the color of solution from blue to colorless by naked-eye. And through the test and calculation, the detection limit of the probe NB-NO₂ ^- is 129 nM. Based on the above excellent characteristics, the probe NB-NO₂ ^- was successfully used for monitoring NO₂ ^- ions in environmental waters and soils.

Suspect screening of antimicrobial agents transformation products in environmental samples development of LC-QTrap method running in pseudo MRM transitions

The aim of the work was to develop a new HPLC-MS/MS method that allows for the simultaneous detection of antimicrobials agents (targeted analysis) and their transformation products (non-targeted analysis), which enabled the elucidation of their transformation pathways in the environment. Targeted analysis was performed for 16 selected antimicrobials agents (AMs) in wastewater collected at different stages of the treatment process and river water from sections before and after wastewater discharge. The samples were collected in the Łyna sewage treatment plant (Olsztyn, Poland) in three measuring periods at different seasons. Analytes were selected from tetracyclines, fluoroquinolones, β-lactams, macrolides, glycopeptides, lincosamides and synthetic antibiotics. As a part of the targeted analysis, 13 AMs were detected in wastewater samples, and 7 of them in river water samples. However, their presence and concentrations were closely related to the type of the sample and the season in which the sample was taken. The highest concentrations of AMs were detected in samples collected in September (max. 1643.7 ng L^-1 TRI), while the lowest AMs concentrations were found in samples collected in June (max. 136.1 ng L^-1 CLR). The total content of AMs in untreated wastewater was in the range of 1.42-1644 ng L^-1, while in the river water was for upstream 1.22-48.73 ng L^-1 and for downstream 2.24-149 ng L^-1. In the non-target analysis, 33 degradation products of the selected AMs were identified, and the transformation pathways of their degradation were speculated. In the course of the research, it was found that as a result of the processes taking place in wastewater treatment plant, the parent substances are transformed into a number of stable transformation products. Transformation products resulted from hydroxylation, ring opening, oxidation, methylation or demethylation, carboxylation, or cleavage of the CN bond of the parent AMs.

Nitrates in the environment: A critical review of their distribution, sensing techniques, ecological effects and remediation

Nitrate pollution is eminent in almost all the developing nations as a result of increased natural activities apart from anthropogenic pollution. The release of nitrates in more than critical quantities into the water bodies causes accretion impacts on living creatures, environmental receptors, and human vigour by accumulation through the food chain. Nitrates have recently acquired researchers' huge attention and extend their roots in environmental contamination of surface and groundwater systems. The presence of nitrate in high concentrations in surface and groundwater triggers several health problems, for instance, methemoglobinemia, diabetes, eruption of infectious disorders, harmfully influence aquatic organisms. Sensing nitrate is an alternate option for monitoring the distribution of nitrate in different water bodies. Here we review electrochemical, spectroscopic, and electrical modes of nitrate sensing. It is concluded that, among the various sensors discussed in this review, FET sensors are the most desirable choice. Their sensitivity, ease of use and scope for miniaturisation are exceptional. Advanced functional materials need to be designed to satiate the growing need for environmental monitoring. Different sources of nitrate contamination in ground and surface water can be estimated using different techniques such as nitrate isotopic composition, co contaminants, water tracers, and other specialized techniques. This review intends to explore the research work on remediation of nitrate from wastewater and soil using different processes such as reverse osmosis, chemical denitrification, biological denitrification, ion exchange, electrodialysis, and adsorption. Denitrification proves as a promising alternative over previously reported techniques in terms of their nitrate removal because of its high cost-effectiveness.

Carbazole-based bis-imidazole ligand-involved synthesis of inorganic–organic hybrid polyoxometalates as electrochemical sensors for detecting bromate and efficient catalysts for selective oxidation of thioether

Considering the potential application on preparing electrode and catalyst materials of inorganic–organic hybrid polyoxometalates, a bis-imidazole ligand with carbazole as a connector, 3,6-di(1H-imidazol-1-yl)-9H-carbazole (L), was used for preparing inorganic–organic hybrid polyoxometalates. As a result, three complexes formulated by [NiL₂(Mo₂O₇)] (1), [Cu(H₂O)₂(HL)₂ (β-Mo₈O₂₆)]·H₂O (2) and [Ni₂(H₂O)₄L₂ (CrMo₆(OH)₅O₁₉)]·6H₂O (3) were obtained successfully. Structural analysis indicated that the different polyoxoanions and metal ions showed important influences on the formation of structures. In the presence of Ni²⁺ ions and heptamolybdate, a 2D network constructed from Ni²⁺ ions and L ligands was formed in complex 1, in which the [Mo₄O₁₄]⁴⁻ polyoxoanions were encapsulated. But the use of Cu²⁺ ions led to a 1D chain of complex 2, which was composed of [β-Mo₈O₂₆]⁴⁻ polyoxoanions and mononuclear {CuL₂} units. By utilizing [CrMo₆(OH)₅O₁₉]⁴⁻ as the inorganic building block, complex 3 showed a 2D (4, 4)-connected layer. Complexes 1–3 could be employed as electrode materials for sensing bromate with the limits of detection of 0.315 μM for 1, 0.098 μM for 2 and 0.551 μM for 3. Moreover, these complexes showed efficient catalytic activity for the selective oxidation of thioethers.

Three inorganic–organic hybrid polyoxometalates were prepared using a bis-imidazole ligand featuring carbazole as a connector, exhibiting not only diverse structures, but also good electrochemical sensing activities for bromate, as well as efficient catalytic performances for oxidation of thioether.

Mesoporous activated carbon as a green adsorbent for the removal of heavy metals and Congo red: Characterization, adsorption kinetics, and isotherm studies

In this study, an effective and green adsorbent was prepared by the self- activation of kenaf fiber and then the kenaf-based activated carbon (KAC) was applied for the removal of lead Pb(II), copper Cu(II), and Congo red (CR) dye from an aqueous solution by the process of adsorption. The surface morphology of mesoporous adsorbent was characterized. The KAC showed good capacity of adsorption of as Pb(II), Cu(II), and anionic dye CR in very short period of agitation. The adsorbent efficiency of metal ions and dye was estimated by varying the adsorbent dose, pH, contact time, initial metals and dye concentration, and temperature. Optimum adsorption of metal ions and CR dye was observed at pH 6, and at pH 4 at 120 min, respectively. The adsorption isotherm was described by the Langmuir and Freundlich isotherm equations. The green adsorbent followed the pseudo-second-order kinetic model with correlation coefficients R² value >0.99. The increase in adsorption temperature enhanced the adsorption efficiency for both heavy metals and dye. The KAC showed no significant loss of the adsorption capacity after 3 cycles of reuse.

Fabrication and application of a MIL-68(In)-NH2 incorporated high internal phase emulsion polymeric monolith as a solid phase extraction adsorbent in triazine herbicide residue analysis

In this work, a metal–organic framework MIL-68(In)–NH₂ incorporated high internal phase emulsion polymeric monolith (MIL-68(In)–NH₂/polyHIPE) was prepared and applied as a solid phase extraction adsorbent for the extraction and detection of trace triazine herbicides in environmental water samples by coupling with HPLC-UV detection. The fabricated material showed good adsorption for simazine, prometryn, and prometon in water samples because of π–π interactions and hydrogen bonding interactions. Under optimal conditions, the maximum adsorption capacity of simazine, prometon and prometryn was 800 μg g⁻¹, 800 μg g⁻¹ and 6.01 mg g⁻¹, respectively. The linearities were 10–800 ng mL⁻¹ for simazine, prometon and prometryn. The limits of detection were 31–97 ng L⁻¹, and the recoveries were 85.6–118.2% at four spiked levels with relative standard deviations lower than 5.0%. The method has a high sensitivity for the determination of three triazine herbicides in environmental water samples.

MIL-68(In)–NH₂ incorporated high internal phase emulsion polymeric monoliths were fabricated and applied to extract and determine triazine herbicide residues in environmental water samples.

Eco-friendly UPLC-MS/MS analysis of possible add-on therapy for COVID-19 in human plasma: Insights of greenness assessment

Facing the pandemic COVID-19 is of highest priority for all researchers nowadays. Recent statistics indicate that the majority of the cases are home-treated. Two drugs of interest, Guaifenesin and Bromohexine HCl, are among the add-on therapy for treatment of COVID-19 mild cases, which has raised the need for their simultaneous determination. The analysis of the two drugs of interest was described using ultra-performance liquid chromatography-tandem mass spectrometric (UPLC-MS/MS) in plasma of healthy human volunteers using tetryzoline HCl as an internal standard (IS) after liquid-liquid extraction. The applied chromatographic conditions were Kinetex C₁₈ (100 Å, 2.6 µm X 50 mm X 4.6 mm) column and a mixture of methanol: water (95: 5, v/v) as a mobile phase at flow rate 1 mL/min. The positive ionization mode was used for detecting the ions, by observing the pairs of transition m/z 199 < 125 for GUF, m/z 377 < 114 for BRM and m/z 201 < 131 for IS. The linearity range was from 50 to 1500 ng/mL for GUF and 0.5-50 µg/mL for BRM. Limit of detection (LOD) was found to be 35.16 and 0.43 ng/ml for GUF and BRM, respectively. The method was validated according to FDA guidance. The proposed method was assessed to be more eco-friendly versus the reported method using the greenness assessment tools: National Environmental Methods Index (NEMI), Assessment of Green Profile (AGP), Green Analytical Procedure Index (GAPI) and Eco-Scale. The proposed method was applied for the application of a pilot pharmacokinetic study.

Choices of chromatographic methods as stability indicating assays for pharmaceutical products: A review

Stability indicating assay describes a technique which is used to analyse the stability of drug substance or active pharmaceutical ingredient (API) in bulk drug and pharmaceutical products. Stability indicating assay must be properly validated as per ICH guidelines. The important components in a stability indicating assay include sensitivity, specificity, accuracy, reliability, reproducibility and robustness. A validated assay is able to measure the concentration changes of drug substance/API with time and make reliable estimation of the quantity of the degradation impurities. The drug substance is separated and resolved from the impurities. Pros and cons of HPLC, GC, HPTLC, CE and SFC were discussed and reviewed. Stability indicating assay may consist of the combination of chromatographic separation and spectroscopic detection techniques. Hyphenated system could demonstrate parallel quantitative and qualitative analysis of drug substances and impurities. Examples are HPLC-DAD, HPLC-FL, GC-MS, LC-MS and LC-NMR. The analytes in the samples are separated in the chromatography while the impurities are chemically characterised by the spectroscopy in the system. In this review, various chromatographic methods which had been employed as stability indicating assays for drug substance and pharmaceutical formulation were systematically reviewed, and the application of hyphenated techniques in impurities characterisation and identification were also discussed with supporting literatures.

HPTLC-densitometry quantification of fructooligosaccharides from inulin hydrolysate

The objective of present research was to develop an easy, precise and accurate HPTLC densitometry method for quantification of fructooligosaccharides (FOSs) from inulin hydrolysate. The chromatographic separation of FOSs was performed on pre-coated silica gel (60, F₂₅₄) TLC plates using a mobile phase (butanol:ethanol:water, 60:24:16), and densitometry evaluation of FOSs was performed at A₅₀₀. Both kestose and nystose were successfully resolved with R_f value of 0.43 and 0.34, respectively. The accuracy, reliability and reproducibility of developed method was assessed by percent relative standard deviation of kestose and nystose for instrument precision (1.43% and 1.50%), repeatability (1.48% and 1.56%), intra-day precision (1.60% and 1.63%), inter-day precision (1.62% and 1.66%), limit of detection (4.58 ng/spot and 4.58 ng/spot), limit of quantification (13.87 ng/spot and 13.89 ng/spot) and recovery (98.81% and 98.69%). Moreover, overlapping spectra of test sample with standard confirms the specificity of developed method, which was validated as per ICH guidelines.

Surfactant-functionalised magnetic ferum oxide coupled with high performance liquid chromatography for the extraction of phenol

The usage of phenols in the marketplace has been increasing tremendously, which has raised concerns about their toxicity and potential effect as emerging pollutants. Phenol's structure has closely bonded phenyl and hydroxy groups, thereby making its functional characteristics closely similar to that of alcohol. As a result, phenol is used as a base compound for commercial home-based products. Hence, a simple and efficient procedure is required to determine the low concentration of phenols in environmental water samples. In this research, a method of combining magnetic nanoparticles (MNPs) with surfactant Sylgard 309 was developed to overcome the drawbacks in the classical extraction methods. In addition, this developed method improved the performance of extraction when MNPs and the surfactant Sylgard 309 were used separately, as reported in the previous research. This MNP-Sylgard 309 was synthesised by the coprecipitation method and attracts phenolic compounds in environmental water samples. Response surface methodology was used to study the parameters and responses in order to obtain an optimised condition using MNP-Sylgard 309. The parameters included the effect of pH, extraction time, and concentration of the analyte. Meanwhile, the responses measured were the peak area of the chromatogram and the percentage recovery. From this study, the results of the optimum conditions for extraction using MNP-Sylgard 309 were pH 7, extraction time of 20 min, and analyte concentration of 10.0 μg mL^-1. Under the optimized conditions, MNP-Sylgard 309 showed a low limit of detection of 0.665 μg mL^-1 and the limit of quantification was about 2.219 μg mL^-1. MNP-Sylgard 309 was successfully applied on environmental water samples such as lake and river water. High recovery (76.23%-110.23%) was obtained.

Nanosilver and protonated carbon nitride co-coated carbon cloth fibers based non-enzymatic electrochemical sensor for determination of carcinogenic nitrite

A novel electrochemical nitrite (NaNO₂) sensor was fabricated by combining nanosilver with protonated carbon nitride (H-C₃N₄) supported on carbon cloth (CC). H-C₃N₄ was distributed uniformly on the CC surface, providing more active sites for the electrocatalytic active center (nanosilver). CC as a substrate improved the H-C₃N₄ conductivity and provided the sensor with a flexible feature. The strong synergistic effect between CC, H-C₃N₄, and nanosilver can exert a significant electrocatalytic performance on the flexible sensor. The Ag/H-C₃N₄/CC flexible sensor electrode did not consume much more time to polish the surface of traditional electrodes, and possessed a high sensitivity of 0.85537 μA/mg, a wide linear response range that spanned 5 to 1000 μM, a low detection limit of 0.216 μM (S/N = 3), and high selectivity for nitrite in the presence of common organic and inorganic interfering species (such as CaCl₂, NaCl, MgCl₂, NaNO₃, glucose, urea, and p-nitrophenol). The Ag/H-C₃N₄/CC flexible sensor can be used for sample detection of nitrite as it has a strong anti-interference ability, good reproducibility, repeatability, and long-term stability. The Ag/H-C₃N₄/CC sensor is a promising alternative electrode to traditional ones such as ITO, gold or glassy carbon electrodes.

UV/sulfite chemistry to reduce N-nitrosodimethylamine formation in chlor(am)inated water

The disinfection by-product N-nitrosodimethylamine (NDMA) is a major concern in water quality management due to its carcinogenicity. Thus, a proper pretreatment is necessary to mitigate NDMA formation upon periodic chloramination by removing precursors, such as ranitidine (RNT). This study investigated the effect of UV/sulfite pretreatment on NDMA formation from an RNT-spiked tap and chloraminated synthetic swimming pool (SSP) water. At UVC intensity of 2.1 mW cm^-2 and 0.5 mM of sulfite, UV/sulfite chemistry showed complete degradation of 20 µM RNT within 30 min. It was found that SO₄^•- primarily reduced the NDMA formation potential (FP) of RNT, while hydrated electrons effectively mitigated the pre-formed NDMA in the SSP water. The UV/sulfite pretreatment alleviated NDMA formation during post-chloramination (24 h) by up to 82%, outperforming the commonly employed advanced oxidation processes such as UV/H₂O₂. However, in the presence of bromide ions, the effectiveness of UV/sulfite pretreatment was seriously deteriorated, although the bromide ion itself was found to inhibit the NDMA formation from RNT especially at pH < 8 during chloramination. Mass spectrometric analysis indicated that the NDMA-FP of RNT could be removed by UV/sulfite principally via N-methylation, dealkylation, and oxygen transfer pathways. Consequently, UV/sulfite could be used as an alternative unit process for water treatment with reduced NDMA formation.

Gold nanoparticles decorated bimetallic CuNi-based hollow nanoarchitecture for the enhancement of electrochemical sensing performance of nitrite

Gold nanoparticles (AuNPs) decorated bimetallic CuNi-based hollow nanoarchitecture (CNHN) are reported for the first time as a nonenzymatic sensor for the quantification of nitrite in neutral solution . The CNHN was prepared via a convenient calcining routine using the bimetallic CuNi-MOFs as a coprecursor. The unique chemical structure of hollow CNHN with high specific surface area and abundant terminal amino groups effectively avoid the aggregation of AuNPs and facilitate the subsequent adsorption of nitrite. The Au/CNHN exhibited high electrocatalytic activity towards nitrite oxidation due to the synergetic catalytic effect of AuNPs and CNHN. Chronoamperometric detection of nitrite at the Au/CNHN/GCE achieved a lower linear calibration range of 0.05 to 1.15 mM, with an LOD of 0.017 μM compared with previous reports. The proposed method obtained satisfactory recoveries for nitrite determination in practical applications, which was verified by UV-Vis spectrophotometry. The prepared sensor based on Au/CNHN featured favorable selectivity and stability, which provides a promising approach for real sample analysis. Graphical abstract.

Hydrothermal synthesis of green fluorescent nitrogen doped carbon dots for the detection of nitrite and multicolor cellular imaging

A fluorescent probe for the determination of nitrite (NO₂^-) was fabricated by using green fluorescent nitrogen doped carbon dots (NCDs). The NCDs were synthesized via a one-pot hydrothermal carbonization of citric acid in the presence of p-phenylenediamine as the nitrogen source. The N content of the NCDs was high to 17.09% and consisted of a variety of functional groups on the NCDs surface, including sp²-hybridized CN, porphyrin C-N-C and amino N in N-(C) ₃ or H-N-(C) ₂ et al. N atoms were also doped within the framework of the NCDs. The almost monodisperse NCDs (average particle diameter = 3.67 nm) exhibited green photoluminescence (PL) with excitation/emission maxima of 360/505 nm. The PL of the NCDs was dependent on both excitation wavelength and solution pH. The NCDs showed a strong PL quenching response to NO₂^- under acidic conditions (pH = 2.5). The PL intensity of the NCDs was inversely proportional to the concentration of NO₂^- between 0.02 and 40 μM (R² = 0.992), with a detection limit of 21.2 nM. The practical use of the nanoprobe for NO₂^- determination in food samples was also demonstrated, successfully. NCD-nitroso compounds formed because of reaction between the abundant amide groups on the surface of NCDs with the NO₂^-, which caused an inner filter effect and static PL quenching. Importantly, the NCDs had low cellular toxicity and were successfully used as a multicolor cellular imaging agent for Hepg2 cells.

Quantification by SIFT-MS of volatile compounds produced by the action of sodium hypochlorite on a model system of infected root canal content

Root canal irrigation with sodium hypochlorite (NaOCl) is an indispensable part of the chemomechanical preparation of infected root canals in Endodontology. However, there is limited information on the emergence of toxic or hazardous volatile compounds (VOCs) from the interaction of NaOCl with the infected content of tooth biomaterials. The aim of this study was to assess the formation of VOCs and disinfection by-products (DBPs) following the interaction of NaOCl 2.5% v/v with a model system of different sources of natural organic matter (NOM) present in infected root canals, including dentine powder, planktonic multi-microbial suspensions (Propionibacterium acnes, Staphylococcus epidermidis, Actinomyces radicidentis, Streptococcus mitis and Enterococcus faecalis strain OMGS3202), bovine serum albumin 4%w/v and their combination. NaOCl was obtained from a stock solution with iodometric titration. Ultrapure water served as negative control. Samples were stirred at 37°C in aerobic and anaerobic conditions for 30min to approximate a clinically realistic time. Centrifugation was performed and the supernatants were collected and stored at -80⁰ C until analysis. The reaction products were analysed in real time by selected ion flow tube mass spectrometry (SIFT-MS) in triplicates. SIFT-MS analysis showed that the released VOCs included chlorinated hydrocarbons, particularly chloroform, together with unexpected higher levels of some nitrogenous compounds, especially acetonitrile. No difference was observed between aerobic and anaerobic conditions. The chemical interaction of NaOCl with NOM resulted in the formation of toxic chlorinated VOCs and DBPs. SIFT-MS analysis proved to be an effective analytical method. The risks from the rise of toxic compounds require further consideration in dentistry.

Determination of nitrite ions in environment analysis with a paper-based microfluidic device

A new microfluidic paper-based analytical device, a (Ag-μPAD)-based chemiresistor composed of silver ink, has been developed for the selective, sensitive, and quantitative determination of nitrite ions in environmental analysis.

A novel photoluminescence sensing system sensitive for and selective to bromate anions based on carbon dots

A simple, highly sensitive and selective PL sensing method for bromate anions has been developed.