Spoilt for choice: A critical review on the chemical and biological assessment of current wastewater treatment technologies

Comparative evaluation of SPE methods for biotoxicity assessment of water and wastewater: Linkage between chemical extracting efficiency and biotoxicity outcome

Biotoxicity assessment results of environmental waters largely depend on the sample extraction protocols that enrich pollutants to meet the effect-trigger thresholds of bioassays. However, more chemical mixture does not necessarily translate to higher combined biotoxicity. Thus, there is a need to establish the link between chemical extracting efficiency and biotoxicity outcome to standardize extraction methods for biotoxicity assessment of environmental waters. This study compares the performance of five different extraction phases in solid phase extraction (SPE), namely HLB, HLB+Coconut, C18 cartridge, C18 disk and Strata-X, and evaluated their chemical extracting efficiencies and biotoxicity outcomes. We quantitatively assessed cytotoxicity, acute toxicity, genotoxicity, estrogenic activity, and neurotoxicity of the extracts using in vitro bioassays and characterized the chemical extracting efficiencies of the SPE methods through chemical recoveries of 23 model compounds with different polarities and total organic carbon. Using Pareto ranking, we identified HLB+Coconut as the optimal SPE method, which exhibited the highest level of water sample biotoxicity and recovered the most chemicals in water samples. We found that the biotoxicity outcomes of the extracted water samples significantly and positively correlated with the chemical extracting efficiencies of the SPE methods. Moreover, we observed synchronous changing patterns in biotoxicity outcome and chemical extracting efficiencies in response to increasing sample volumes per cartridge (SVPC) during SPE. Our findings underscore that higher chemical extracting efficiency of SPE corresponds to higher biotoxicity outcome of environmental water samples, providing a scientific basis for standardization of SPE methods for adequate assessment of biotoxicities of environmental waters.

Adaption and application of cell-based bioassays to whole-water samples

The increasing presence of contaminants of emerging concern in wastewater and their potential environmental risks require improved monitoring and analysis methods. Direct toxicity assessment (DTA) using bioassays can complement chemical analysis of wastewater discharge, but traditional in vivo tests have ethical considerations and are expensive, low-throughput, and limited to apical endpoints (mortality, reproduction, development, and growth). In vitro bioassays offer an alternative approach that is cheaper, faster, and more ethical, and can provide higher sensitivity for some environmentally relevant endpoints. This study explores the potential benefits of using whole water samples of wastewater and environmental surface water instead of traditional solid phase extraction (SPE) methods for in vitro bioassays testing. Whole water samples produced a stronger response in most bioassays, likely due to the loss or alteration of contaminants during SPE sample extraction. In addition, there was no notable difference in results for most bioassays after freezing whole water samples, which allows for increased flexibility in testing timelines and cost savings. These findings highlight the potential advantages of using whole water samples in DTA and provide a framework for future research in this area.

Advanced oxidation processes for water and wastewater treatment - Guidance for systematic future research

Advanced oxidation processes (AOPs) are a growing research field with a large variety of different process variants and materials being tested at laboratory scale. However, despite extensive research in recent years and decades, many variants have not been transitioned to pilot- and full-scale operation. One major concern are the inconsistent experimental approaches applied across different studies that impede identification, comparison, and upscaling of the most promising AOPs. The aim of this tutorial review is to streamline future studies on the development of new solutions and materials for advanced oxidation by providing guidance for comparable and scalable oxidation experiments. We discuss recent developments in catalytic, ozone-based, radiation-driven, and other AOPs, and outline future perspectives and research needs. Since standardized experimental procedures are not available for most AOPs, we propose basic rules and key parameters for lab-scale evaluation of new AOPs including selection of suitable probe compounds and scavengers for the measurement of (major) reactive species. A two-phase approach to assess new AOP concepts is proposed, consisting of (i) basic research and proof-of-concept (technology readiness levels (TRL) 1-3), followed by (ii) process development in the intended water matrix including a cost comparison with an established process, applying comparable and scalable parameters such as UV fluence or ozone consumption (TRL 3-5). Subsequent demonstration of the new process (TRL 6-7) is briefly discussed, too. Finally, we highlight important research tools for a thorough mechanistic process evaluation and risk assessment including screening for transformation products that should be based on chemical logic and combined with complementary tools (mass balance, chemical calculations).

Comprehensive analysis of a widely pharmaceutical, furosemide, and its degradation products in aquatic systems: Occurrence, fate, and ecotoxicity

Many pharmaceutical compounds end up in the environment due to incomplete removal by wastewater treatment plants (WWTPs). Some compounds are sometimes present in significant concentrations and therefore represent a risk to the aquatic environment. Furosemide is one of the most widely used drugs in the world. Considered as an essential drug by the World Health Organization, this powerful loop diuretic is used extensively to treat hypertension, heart and kidney failure and many other purposes. However, this important consumption also results in a significant release of furosemide in wastewater and in the receiving environment where concentrations of a few hundred ng/L to several thousand have been found in the literature, making furosemide a compound of great concern. Also, during its transport in wastewater systems and WWTPs, furosemide can be degraded by various processes resulting in the production of more than 74 by-products. Furosemide may therefore present a significant risk to ecosystem health due not only to its direct cytotoxic, genotoxic and hepatotoxic effects in animals, but also indirectly through its transformation products, which are poorly characterized. Many articles classify furosemide as a priority pollutant according to its occurrence in the environment, its persistence, its elimination by WWTPs, its toxicity and ecotoxicity. Here, we present a state-of-the-art review of this emerging pollutant of interest, tracking it, from its consumption to its fate in the aquatic environment. Discussion points include the occurrence of furosemide in various matrices, the efficiency of many processes for the degradation of furosemide, the subsequent production of degradation products following these treatments, as well as their toxicity.

Influence of ozonation and UV/H2O2 on the genotoxicity of secondary wastewater effluents

The implementation of novel wastewater treatment technologies, including Advanced Oxidation Processes (AOPs) such as ozonation and ultraviolet radiation (UV) combined with hydrogen peroxide (H2O2), can be a promising strategy for enhancing the quality of these effluents. However, during effluent oxidation AOPs may produce toxic compounds that can compromise the water reuse and the receiving water body. Given this possibility, the aim of this study was to evaluate the genotoxic potential of secondary effluents from two different Wastewater Treatment Plants (WWTP) that were subjected to ozonation or UV/H2O2 for periods of 20 (T1) and 40 (T2) minutes. The genotoxic potential was carried out with the Comet assay (for clastogenic damage) and the Micronucleus assay (for clastogenic and aneugenic damage) in HepG2/C3A cell culture (metabolizing cell line). The results of the comet assay revealed a significant increase in tail intensity in the Municipal WWTP (dry period) effluents treated with UV/H2O2 (T1 and T2). MN occurrence was noted across all treatments in both Pilot and Municipal WWTP (dry period) effluents, whereas nuclear buds (NBs) were noted for all Pilot WWTP treatments and UV/H2O2 treatments of Municipal WWTP (dry period). Moreover, the UV/H2O2 (T1) treatment of Municipal WWTP (dry period) exhibited a noteworthy incidence of multiple alterations per cell (MN + NBs). These findings imply that UV/H2O2 treatment demonstrates higher genotoxic potential compared to ozonation. Furthermore, seasonal variations can have an impact on the genotoxicity of the samples. Results of the study emphasize the importance of conducting genotoxicological tests using human cell cultures, such as HepG2/C3A, to assess the final effluent quality from WWTP before its discharge or reuse. This precaution is essential to safeguard the integrity of the receiving water body and, by extension, the biotic components it contains.

Oxidation processes and me

This publication summarizes my journey in the field of chemical oxidation processes for water treatment over the last 30+ years. Initially, the efficiency of the application of chemical oxidants for micropollutant abatement was assessed by the abatement of the target compounds only. This is controlled by reaction kinetics and therefore, second-order rate constant for these reactions are the pre-requisite to assess the efficiency and feasibility of such processes. Due to the tremendous efforts in this area, we currently have a good experimental data base for second-order rate constants for many chemical oxidants, including radicals. Based on this, predictions can be made for compounds without experimental data with Quantitative Structure Activity Relationships with Hammet/Taft constants or energies of highest occupied molecular orbitals from quantum chemical computations. Chemical oxidation in water treatment has to be economically feasible and therefore, the extent of transformation of micropollutants is often limited and mineralization of target compounds cannot be achieved under realistic conditions. The formation of transformation products from the reactions of the target compounds with chemical oxidants is inherent to oxidation processes and the following questions have evolved over the years: Are the formed transformation products biologically less active than the target compounds? Is there a new toxicity associated with transformation products? Are transformation products more biodegradable than the corresponding target compounds? In addition to the positive effects on water quality related to abatement of micropollutants, chemical oxidants react mainly with water matrix components such as the dissolved organic matter (DOM), bromide and iodide. As a matter of fact, the fraction of oxidants consumed by the DOM is typically > 99%, which makes such processes inherently inefficient. The consequences are loss of oxidation capacity and the formation of organic and inorganic disinfection byproducts also involving bromide and iodide, which can be oxidized to reactive bromine and iodine with their ensuing reactions with DOM. Overall, it has turned out in the last three decades, that chemical oxidation processes are complex to understand and to manage. However, the tremendous research efforts have led to a good understanding of the underlying processes and allow a widespread and optimized application of such processes in water treatment practice such as drinking water, municipal and industrial wastewater and water reuse systems.

Critical review on organophosphate esters in water environment: Occurrence, health hazards and removal technologies

Organophosphate esters (OPEs), which are phosphoric acid ester derivatives, are anthropogenic substances that are widely used in commerce. Nevertheless, there is growing public concern about these ubiquitous contaminants, which are frequently detected in contaminated water sources. OPEs are mostly emitted by industrial operations, and the primary routes of human exposure to OPEs include food intake and dermal absorption. Because of their negative effects on both human health and the environment, it is clear that innovative methods are needed to facilitate their eradication. In this study, we present a comprehensive overview of the existing characteristics and origins of OPEs, their possible impacts on human health, and the merits, drawbacks, and future possibilities of contemporary sophisticated remediation methods. Current advanced remediation approaches for OPEs include adsorption, degradation (advanced oxidation, advanced reduction, and redox technology), membrane filtration, and municipal wastewater treatment plants, degradation and adsorption are the most promising removal technologies. Meanwhile, we proposed potential areas for future research (appropriate management approaches, exploring the combination treatment process, economic factors, and potential for secondary pollution). Collectively, this work gives a comprehensive understanding of OPEs, providing useful insights for future research on OPEs pollution.

Emerging contaminants and their potential impacts on estuarine ecosystems: Are we aware of it?

Emerging contaminants (ECs) are becoming more prevalent in estuaries and constitute a danger to both human health and ecosystems. These pollutants can infiltrate the ecosystem and spread throughout the food chain. Because of the diversified sources and extensive human activities, estuaries are particularly susceptible to increased pollution levels. A thorough review on recent ECs (platinum group elements, pharmaceuticals and personal care products, pesticides, siloxanes, liquid crystal monomers, cationic surfactant, antibiotic resistance genes, and microplastics) in estuaries, including their incidence, detection levels, and toxic effects, was performed. The inclusion of studies from different regions highlights the global nature of this issue, with each location having its unique set of contaminants. The diverse range of contaminants detected in estuary samples worldwide underscores the intricacy of ECs. A significant drawback is the scarcity of research on the toxic mechanisms of ECs on estuarine organisms, the prospect of unidentified ECs, warrant research scopes.

Predicting Transformation Products during Aqueous Oxidation Processes: Current State and Outlook

Water quality and its impacts on human and ecosystem health presents tremendous global challenges. While oxidative water treatment can solve many of these problems related to hygiene and micropollutants, identifying and predicting transformation products from a large variety of micropollutants induced by dosed chemical oxidants and in situ formed radicals is still a major challenge. To this end, a better understanding of the formed transformation products and their potential toxicity is needed. Currently, no theoretical tools alone can predict oxidatively induced transformation products in aqueous systems. Coupling experimental and theoretical studies has advanced the understanding of reaction kinetics and mechanisms significantly. This perspective article highlights the key progress made concerning experimental and computational approaches to predict transformation products. Knowledge gaps are identified, and the research required to advance the predictive capability is discussed.

Redox-directed identification of toxic transformation products during ozonation of aromatics

The toxicity assessment of transformation products (TPs) formed in oxidative water treatment is crucial but challenging because of their low concentration, structural diversity, and mixture complexity. Here, this study developed a novel redox-directed approach for identification of toxic TPs without the individual toxicity and concentration information. This approach based on sodium borohydride reduction comprised an integrated process of toxicological evaluation, fluorescence excitation-emission matrix characterization, high-resolution mass spectrometry detection, followed by ecological toxicity assessment of identified TPs. The redox-directed identification of primary causative toxicants was experimentally tested for the increased nonspecific toxicity observations in the ozonated effluents of model aromatics. Reduction reaction caused a remarkable decrease in toxicity and increase in fluorescence intensity, obtaining a good linear relation between them. More than ten monomeric or dimeric p-benzoquinone (p-BQ) TPs were identified in the ozonated effluents. The occurrence of the p-BQ TPs was further verified through parallel sodium sulfite reduction and actual wastewater ozonation experiments. In vitro bioassays of luminescent bacteria, as well as in silico genotoxicity and cytotoxicity predictions, indicate that the toxicity of p-BQ TPs is significantly higher than that of their precursors and other TPs. These together demonstrated that the identified p-BQ TPs are primary toxicity contributors. The redox-directed approach facilitated the revelation of primary toxicity contribution, illustrating emerging p-BQs are a concern for aquatic ecosystem safety in the oxidative treatment of aromatics-contaminated wastewater.

Recovery of electron and carbon source from agricultural waste corncob by microbial electrochemical system to enhance wastewater denitrification

The denitrification process in wastewater treatment plants (WWTPs) is limited by insufficient carbon sources. Agricultural waste corncob was investigated for its feasibility as a low-cost carbon source for efficient denitrification. The results showed that the corncob as the carbon source exhibited a similar denitrification rate (19.01 ± 0.03 gNO₃^--N/m³d) to that of the traditional carbon source sodium acetate (19.13 ± 0.37 gNO₃^--N/m³d). When filling corncob into a microbial electrochemical system (MES) three-dimensional anode, the release of corncob carbon sources was well controlled with an improved denitrification rate (20.73 ± 0.20 gNO₃^--N/m³d). Carbon source and electron recovered from corncob led to autotrophic denitrification and heterotrophic denitrification occurred in the MES cathode, which synergistically improved the denitrification performance of the system. The proposed strategy for enhanced nitrogen removal by autotrophic coupled with heterotrophic denitrification using agricultural waste corncob as the sole carbon source opened up an attractive route for low-cost and safe deep nitrogen removal in WWTPs and resource utilization for agricultural waste corncob.

pH-Tunable electrokinetic movement of droplets

Manipulation and control of droplet motion in an electric field is of interest in biological systems, microfluidics and electrokinetic (EK) separation techniques. In this work, we show that the electrokinetic motion of oil-in-water (O/W) emulsions stabilized by an amphoteric surfactant can be controlled by changing the pH. Amphoteric surfactants carry both positive and negative head groups and change charge under the influence of changing pH, which allows them to impact the surface charge of droplets as a function of pH, and in extension their direction of motion in an electric field. Using a microfluidic system, we evaluate the effect of pH, surfactant concentration and droplet size on the EK velocity of droplets, which is a combination of electrophoresis (EP) and electro-osmotic flow (EOF). We show that by changing the pH from acidic to alkali, the direction of droplet motion in an external electric field changes. The magnitude of the EK velocity at acidic and neutral pH is not significantly altered as a result of the competition of the EP and EOF in the system, which generally have opposite directions. Our results are in good agreement with theoretical predictions for the droplet EP mobility and can thus serve as a verification of the theoretical descriptions. In addition to the pH, the surfactant concentration affects droplet EK velocity, most specifically at pH of 7 which is close to the isoelectric point of the surfactant monomers. At this pH, changing the surfactant concentration changes the direction of droplet motion due the competing effect of the EP and EOF at different surfactant concentrations. By increasing the droplet size, the magnitude of the EK velocity increases because of the larger local ζ-potential of the larger droplets as well as the wall-enhanced effect in the system. The results from this work can be applied to design on-chip droplet separation strategies based on pH variations and are relevant for systems in which pH gradients naturally occur, such as the human body.

Occurrence and fate of an emerging drug pollutant and its by-products during conventional and advanced wastewater treatment: Case study of furosemide

Conventional wastewater treatment systems are not designed to remove pharmaceutical compounds from wastewater. These compounds can be degraded into many other transformation products which are hardly, if at all, studied. In this context, we studied the occurrence and degradation of furosemide, a very frequently detected diuretic, along with its known degradation products in several types of wastewater. Influent and effluent from the Seine-Centre Wastewater Treatment Plant (WWTP) (Paris, France) as well as outlet of residential care homes (Dordogne, France) were analyzed by Ultra-Performance Liquid Chromatography-tandem Mass Spectrometry (UPLC-MS/MS) to quantify furosemide and its known degradation products, saluamine and pyridinium of furosemide. Oxidation experiments (chlorination, ozonation and UV photolysis with hydrogen peroxide) were then performed on furosemide solutions and on water from residential care facilities to study the degradation of furosemide by potential advanced processes, and also to identify unknown oxidation products by high-resolution mass spectrometry. Furosemide was well degraded in Seine-Centre WWTP (>75%) but did not increase the concentrations of its main degradation products. Saluamine and pyridinium of furosemide were already present at similar concentrations to furosemide in the raw wastewater (∼2.5-3.5 μg.L^-1), and their removal in the WWTPs were very high (>80%). Despite their removal, the three compounds remained present in treated wastewater effluents at concentrations of hundreds of nanograms per liter. Chlorination degraded furosemide without pyridinium production unlike the other two processes. Chlorination and ozonation were also effective for the removal of furosemide and pyridinium in residential care home water, but they resulted in the production of saluamine. To our knowledge this is the first evidence of saluamine and pyridinium of furosemide in real water samples in either the particulate or dissolved phase.

Physicochemical pre- and post-treatment of coking wastewater combined for energy recovery and reduced environmental risk

In this study, physicochemical pre- and post-treatment of highly polluting coking wastewater (CWW) for the removal of refractory compounds and recovery of high-energy substances/components was investigated. An economic optimization model targeting the development of a cost-effective and sustainable treatment technology was proposed. At the post-treatment stage, powdered activated carbon (PAC) was used to separate the refractory and toxic pollutants from the bio-treated CWW, with the adsorption capacity ranging from 50 to 120 mg chemical oxygen demand (COD) g^-1 PAC. Then, the spent PAC, together with a coagulant, was reused in the pre-treatment of highly concentrated raw CWW, which lifted the adsorption capacity to 800-1200 mg COD g^-1 PAC. Results showed that the adsorbent's high selectivity towards macromolecular and complicated pollutants could remove 25-65 % of COD in both CWW flows. Analysis of pollutants' molecular weight distribution and GC-MS indicated a good affinity between PAC and high-energy pollutants (phenolic compounds and alkanes), which could transfer 144,555 kJ m^-3 of energy from CWW to the adsorption-coagulation sludge. The economic optimization model suggested that the cost of the adsorbent was compensated by the net benefits of energy recovery and that profit was achieved when the PAC price was less than 5562 CNY t^-1. The proposed two-stage PAC/coagulant approach offers a way to sustainable water quality and sludge management, plus energy recycling, in CWW treatment. It may also be applied to the treatment of other industrial wastewaters.

On-site determination of water toxicity based on freeze-dried electrochemically active bacteria

Our previous studies have reported water toxicity determination with a fresh electrochemically active bacteria (EAB) suspension as the sensing element, which exhibits high sensitivity and has great prospects in providing early warning about water pollution. However, because the preparation of fresh EAB suspensions is time-consuming, these studies are not suitable for the on-site determination of water toxicity. To solve this problem, this study investigated the rapid preparation of an EAB suspension by the rehydration of freeze-dried EABs and established a novel method for the on-site determination of water toxicity based on the freeze-dried EAB model strain Shewanella oneidensis MR-1. The results demonstrate that the optimal cryoprotectant for S. oneidensis MR-1 freeze drying is 7.5 % (w/v) skimmed milk powder. Compared with fresh S. oneidensis MR-1, freeze-dried S. oneidensis MR-1 exhibits similar extracellular electron transfer (EET) performance (74.7 % ± 0.3 %) and slightly lower sensitivity for water toxicity determination (65.8 % ± 2.2 %) with the optimal cryoprotectant. On-site determination of water toxicity was realized by using freeze-dried S. oneidensis MR-1, and the detection limits of five common toxic pollutants (Cd²⁺, Pb²⁺, Cu²⁺, phenol and dichlorophenol) reached 0.5 mg/L. Water toxicity determination is capable of resisting common interferences, e.g., glucose, lactate, nitrate and nitrite, and shows high accuracy in practical applications.

Performance and degradation mechanism of phycocyanin by Cu-TiO2 photocatalytic treatment

The efficiency, transformation products, and mechanism of phycocyanin removal from water by simulated sunlight/Cu-decorated TiO₂ photocatalyst treatment were studied. After 360 min of photocatalytic degradation, the removal rate of PC was higher than 96%, about 47% of DON was oxidized into NH⁴⁺-N, NO^3- and NO^2-. ·OH was the main active species in the photocatalytic system, which contributes about 55.7% to PC degradation efficiency, H⁺ and ·O^2- also contributed to the photocatalytic activity. The degradation process of phycocyanin is firstly caused by the attack of free radicals, which leads to the disintegration of the chromophore group PCB and the apoprotein, and then apoprotein peptide chain was broken to generate small molecule dipeptides, amino acids, and their derivatives. Amino acid residues sensitive to free radical action in phycocyanin peptide chain include most hydrophobic amino acids such as leucine, isoleucine, proline, valine, phenylalanine, and some hydrophilic amino acids which are easily oxidized such as lysine and arginine. Small molecular peptides (dipeptides), amino acids, and their derivatives are broken off and released into water bodies for further reaction and degradation into smaller molecular weight substances. During this process, part of organic nitrogen was transferred to inorganic nitrogen. When photocatalytic oxidation lasts for 300 min, NH⁴⁺ increases from 0.41 mg/L to 2.21 mg/L, and DON removal rate reaches 47%. The Cu-TiO₂ photocatalyst was found to decrease the CHCl₃ formation potential; however, it exacerbated the production of dichloroacetamide (DCAcAm) and dichloroacetonitrile (DCAN) beyond their initial levels. The divergent trends of these disinfection by-products are due to the fundamental differences in the precursor material.

Ozonation of lake water and wastewater: Identification of carbonous and nitrogenous carbonyl-containing oxidation byproducts by non-target screening

Ozonation of drinking water and wastewater is accompanied by the formation of disinfection byproducts (DBPs) such as low molecular weight aldehydes and ketones from the reactions of ozone with dissolved organic matter (DOM). By applying a recently developed non-target workflow, 178 carbonous and nitrogenous carbonyl compounds were detected during bench-scale ozonation of two lake waters and three secondary wastewater effluent samples and full-scale ozonation of secondary treated wastewater effluent. An overlapping subset of carbonyl compounds (20%) was detected in all water types. Moreover, wastewater effluents showed a significantly higher fraction of N-containing carbonyl compounds (30%) compared to lake water (17%). All carbonyl compounds can be classified in 5 main formation trends as a function of increasing specific ozone doses. Formation trends upon ozonation and comparison of results in presence and absence of the ^•OH radical scavenger DMSO in combination with kinetic and mechanistic information allowed to elucidate potential carbonyl structures. A link between the detected carbonyl compounds and their precursors was established by ozonating six model compounds (phenol, 4-ethylphenol, 4-methoxyphenol, sorbic acid, 3-buten-2-ol and acetylacetone). About one third of the detected carbonous carbonyl compounds detected in real waters was also detected by ozonating model compounds. Evaluation of the non-target analysis data revealed the identity of 15 carbonyl compounds, including hydroxylated aldehydes and ketones (e.g. hydroxyacetone, confidence level (CL) = 1), unsaturated dicarbonyls (e.g. acrolein, CL = 1; 2-butene-1,4-dial, CL = 1; 4-oxobut-2-enoic acid, CL = 2) and also a nitrogen-containing carbonyl compound (2-oxo-propanamide, CL =1). Overall, this study shows the formation of versatile carbonous and nitrogenous carbonyl compounds upon ozonation involving ozone and ^•OH reactions. Carbonyl compounds with unknown toxicity might be formed, and it could be demonstrated that acrolein, malondialdehyde, methyl glyoxal, 2-butene-1,4-dial and 4-oxo-pentenal are degraded during biological post-treatment.

Reduced Graphene Oxide/Waste-Derived TiO2 Composite Membranes: Preliminary Study of a New Material for Hybrid Wastewater Treatment

This work reports the preliminary results of the development of composite self-assembling membranes obtained by the combination of reduced graphene oxide (rGO) with commercial Degussa P25 titanium dioxide (TiO₂). The purpose is to demonstrate the possibility of combining, in the same self-standing material, the capability to treat wastewater containing both inorganic and organic pollutants by exploiting the established ability of rGO to capture metal ions together with that of TiO₂ to degrade organic substances. Moreover, this study also investigates the potential photocatalytic properties of tionite (TIO), to demonstrate the feasibility of replacing commercial TiO₂ with such waste-derived TiO₂-containing material, fulfilling a circular economy approach. Thus, rGO-TiO₂ and rGO-TIO composite membranes, 1:1 by weight, were prepared and characterized by SEM-EDX, XRD, thermogravimetry, as well as by Raman and UV-Vis spectroscopies to verify the effective and homogeneous integration of the two components. Then, they were tested towards 3-mg L^-1 aqueous synthetic solutions of Fe³⁺ and Cu²⁺ ions to evaluate their metal adsorption ability, with values of the order of 0.1-0.2 mmol g_membrane^-1, comparable or even slightly higher than those of pristine rGO. Finally, the ability of the composites to degrade a common organic pesticide, i.e., Imidacloprid^®, was assessed in preliminary photocatalysis experiments, in which maximum degradation efficiencies of 25% (after 3 h) for rGO-TiO₂ and of 21% (after 1 h) for rGO-TIO were found. The result of tionite-containing membranes is particularly promising and worthy of further investigation, given that the anatase content of tionite is roughly 1/6 of the one in commercial TiO₂.

Performance and microbial mechanism of eletrotrophic bio-cathode denitrification under low temperature

Insufficient amount of carbon in wastewater and low temperatures hinder the use of biological nitrogen removal for purification of wastewaters. Nitrogen removal using cold-tolerant electrotrophic cathodic microbes is a novel and unique autotrophic denitrification technique in which electrical current, not chemicals, is used as a source of electrons. In this study, integrated MFC (R_W) and open-circuit MFC (R_O) were cultured and acclimatized in stages at a low temperature (10 °C) to impart cold tolerance to electrotrophic cathodic microbes, investigate the effectiveness of simultaneous nitrification and denitrification (SND) process, and address the possible mechanism of microbial action. The results showed that (i) microbial communities in the R_W system were successfully enriched with the cold-tolerant electrotrophic cathodic microbes after five stages, and (ii) the degree of NH₄⁺-N removal and SND were 75.50% and 81.91%, respectively, but the respective values in the R_O system were only 40.47% and 54.01%. The desirable SND efficiency was obtained in R_W at a DO of ∼0.6 mg/L, a current of ∼20 mA, and pH ∼7.0. In R_W, Thauera, Pesudomonas, and Hydrogenophaga were the main electrotrophic cathodic denitrifying bacteria with cold tolerance capable of degrading ammonia, nitrate, and nitrite through autotrophic denitrification and cathodic-driven bio-electrochemical denitrification. Besides, for R_W, results from high throughput sequencing analysis revealed that the abundance of genes related to energy production and conversion, amino acid transport, and metabolism, signal transduction, environmental adaptation, and enzymatic activity (AMO, HAO, NAR, NIR, NOR, and NOS) were significantly higher than the corresponding parameters of the R_O system. This may explain the reason behind R_W having excellent ammonia and TN removal performance at low temperatures.

Review of ecologically relevant in vitro bioassays to supplement current in vivo tests for whole effluent toxicity testing - Part 1: Apical endpoints

Whole effluent toxicity (WET) testing is commonly used to ensure that wastewater discharges do not pose an unacceptable risk to receiving environments. Traditional WET testing involves exposing animals to (waste)water samples to assess four major ecologically relevant apical endpoints: mortality, growth, development, and reproduction. Recently, with the widespread implementation of the 3Rs to replace, reduce and refine the use of animals in research and testing, there has been a global shift away from in vivo testing towards in vitro alternatives. However, prior to the inclusion of in vitro bioassays in regulatory frameworks, it is critical to establish their ecological relevance and technical suitability. This is part 1 of a two-part review that aims to identify in vitro bioassays that can be used in WET testing and relate them to ecologically relevant endpoints through toxicity pathways, providing the reader with a high-level overview of current capabilities. Part 1 of this review focuses on four apical endpoints currently included in WET testing: mortality, growth, development, and reproduction. For each endpoint, the link between responses at the molecular or cellular level, that can be measured in vitro, and the adverse outcome at the organism level were established through simplified toxicity pathways. Additionally, literature from 2015 to 2020 on the use of in vitro bioassays for water quality assessments was reviewed to identify a list of suitable bioassays for each endpoint. This review will enable the prioritization of relevant endpoints and bioassays for incorporation into WET testing.

Review of ecologically relevant in vitro bioassays to supplement current in vivo tests for whole effluent toxicity testing - Part 2: Non-apical endpoints

Whole effluent toxicity (WET) testing uses whole animal exposures to assess the toxicity of complex mixtures, like wastewater. These assessments typically include four apical endpoints: mortality, growth, development, and reproduction. In the last decade, there has been a shift to alternative methods that align with the 3Rs to replace, reduce, and refine the use of animals in research. In vitro bioassays can provide a cost-effective, high-throughput, ethical alternative to in vivo assays. In addition, they can potentially include additional, more sensitive, environmentally relevant endpoints than traditional toxicity tests. However, the ecological relevance of these endpoints must be established before they are adopted into regulatory frameworks. This is Part 2 of a two-part review that aims to identify in vitro bioassays that are linked to ecologically relevant endpoints that could be included in WET testing. Part 2 of this review focuses on non-apical endpoints that should be incorporated into WET testing. In addition to the four apical endpoints addressed in Part 1, this review identified seven additional toxic outcomes: endocrine disruption, xenobiotic metabolism, carcinogenicity, oxidative stress, inflammation, immunotoxicity and neurotoxicity. For each, the response at the molecular or cellular level measured in vitro was linked to the response at the organism level through a toxicity pathway. Literature from 2015 to 2020 was used to identify suitable bioassays that could be incorporated into WET testing.

Wastewater toxicity removal: Integrated chemical and effect-based monitoring of full-scale conventional activated sludge and membrane bioreactor plants

The literature is currently lacking effect-based monitoring studies targeted at evaluating the performance of full-scale membrane bioreactor plants. In this research, a monitoring campaign was performed at a full-scale wastewater treatment facility with two parallel lines (traditional activated sludge and membrane bioreactor). Beside the standard parameters (COD, nitrogen, phosphorus, and metals), 6 polynuclear aromatic hydrocarbons, 29 insecticides, 2 herbicides, and 3 endocrine disrupting compounds were measured. A multi-tiered battery of bioassays complemented the investigation, targeting different toxic modes of action and employing various biological systems (uni/multicellular, prokaryotes/eukaryotes, trophic level occupation). A traffic light scoring approach was proposed to quickly visualize the impact of treatment on overall toxicity that occurred after the exposure to raw and concentrated wastewater. Analysis of the effluents of the CAS and MBR lines show very good performance of the two systems for removal of organic micropollutants and metals. The most noticeable differences between CAS and MBR occurred in the concentration of suspended solids; chemical analyses did not show major differences. On the other hand, bioassays demonstrated better performance for the MBR. Both treatment lines complied with the Italian law's "ecotoxicity standard for effluent discharge in surface water". Yet, residual biological activity was still detected, demonstrating the adequacy and sensitivity of the toxicological tools, which, by their inherent nature, allow the overall effects of complex mixtures to be taken into account.

European scale assessment of the potential of ozonation and activated carbon treatment to reduce micropollutant emissions with wastewater

Micropollutants (MPs) in wastewater pose a growing concern for their potential adverse effects on the receiving aquatic environment, and some countries have started requiring that wastewater treatment plants remove them to a certain extent. Broad spectrum advanced treatment processes, such as ozonation, activated carbon or their combination, are expected to yield a significant reduction in the toxicity of effluents. Here we quantify the reduction of effluent toxicity potentially achieved by implementing these advanced treatment solutions in a selection of European wastewater treatment plants. To this end, we refer to a list of "total pollution proxy substances" (TPPS) composed of 1337 chemicals commonly found in wastewater effluents according to a compilation of datasets of measured concentrations. We consider these substances as an approximation of the "chemical universe" impinging on the European wastewater system. We evaluate the fate of the TPPS in conventional and advanced treatment plants using a compilation of experimental physicochemical properties that describe their sorption, volatilization and biodegradation during activated sludge treatment, as well as known removal efficiency in ozonation and activated carbon treatment, while filling the gaps through in silico prediction models. We estimate that the discharge of micropollutants with wastewater effluents in the European Union has a cumulative MP toxicity to the environment equal to the discharge of untreated wastewater of ca. 160 million population equivalents (PE), i.e. about 30 % of the generated wastewater in the EU. If all plants above a capacity of 100,000 PE were equipped with advanced treatment, we show that this load would be reduced to about 95 million PE. In addition, implementing advanced treatment in wastewater plants above 10,000 PE discharging to water bodies with an average dilution ratio smaller than 10 would yield a widespread improvement in terms of exposure of freshwater ecosystems to micropollutants, almost halving the part of the stream network exposed to the highest toxic risks. Our analysis provides background for a cost-effectiveness appraisal of advanced treatment "at the end of the pipe", which could lead to optimized interventions. This should not be regarded as a stand-alone solution, but as a complement to policies for the control of emissions at the source for the most problematic MPs.

Effects of microplastic sorption on microbial degradation of halogenated polycyclic aromatic hydrocarbons in water

Halogenated PAHs (HPAHs) are ubiquitous in the environment and have a toxicity similar to that of dioxin. Microplastics exist widely in the environment, and their sorption allows them to act as carriers of HPAHs, potentially changing the bioavailability of HPAHs. However, to the best of our knowledge related studies are limited. In this study, degrading bacteria of five HPAHs were cultivated from mangrove sediments. Among them, the Hyphomicrobium genus has good degradation ability on 9-BrAnt, 2-BrPhe and 2-ClPhe. The degradation process is in line with the first-order degradation kinetic characteristics. The kinetic equations of five kinds of HPAHs showed that the degradation half-lives are 0.65 days (2-BrFle), 0.79 days (9-ClPhe), 1.50 days (2-ClAnt), 5.94 days (9-BrPhe) and 14.1 days (9-BrAnt). The greater the number of benzene rings and the heavier the halogen substituents, the slower the degradation of HPAHs. The sorption of microplastics inhibited the biodegradation of HPAHs, and the degradation half-life of HPAHs will be extended from 0.65 to 14.1 days (the average is 4.59 days) to 1.71-9.93 days (average 5.40 days) for PA, 0.70-35.2 days (average 12.8 days) for PE, 6.02-28.2 (average 15.7 days) days for POM, and 4.60-24.0 (average 19.2 days) days for PP, which is mainly related to the partition coefficient between microplastics and water. This study provides a reference for reducing the uncertainty of the ecological risk assessment of HOCs in the aquatic environment.

A Critical Review on Chemical Speciation of Chlorine-Produced Oxidants (CPOs) in Seawater. Part 1: Chlorine Chemistry in Seawater and Its Consequences in Terms of Biocidal Effectiveness and Environmental Impact

Seawater chlorination has three main industrial uses: disinfection of water and installations, control of biofouling, and preventing the transport of aquatic invasive species. Once in contact with seawater, chlorine reacts rapidly with water constituents (e.g. bromide ions, ammonia, and nitrogen-containing compounds) to form a range of oxidative species (e.g. bromine and N-haloamines), termed "chlorine-produced oxidants" (CPOs) or "total residual oxidants" (TRO). The chemical nature of CPOs and their concentration are a function of two categories of parameters related to treatment modality (e.g. chlorine dose) and water quality (e.g. temperature, pH, ammonia concentration, and organic constituents). The chlorination process may result in continuous or intermittent releases of CPOs in seawater. The reactivity and potential ecotoxicity of CPO species largely depend on their physical and chemical properties. Therefore, evaluation of the biocidal effectiveness of chlorination and its potential impacts requires not only determining the sum of CPOs (via a bulk parameter), but also their chemical speciation. The aim of this article - which is the first of a trilogy dedicated to the chemical speciation of CPOs in seawater - is to provide an overview of current knowledge about chlorine chemistry in seawater and to discuss the biocidal efficacy and the environmental fate of resulting CPOs. The 2nd and 3rd articles delineate a comprehensive and critical review of analytical methods and approaches for the determination of CPOs in seawater.

Comparative study of UV/H2O2 and UV/PMS processes for treating pulp and paper wastewater

Pulp and paper wastewater (PPWW) contains numerous refractory and harmful contaminants that require advanced treatment to meet the discharge criteria. This study compared the efficacy of two PPWW treatments: ultraviolet/peroxymonosulfate (UV/PMS) and ultraviolet/H₂O₂ (UV/H₂O₂) working under similar circumstances. The initial pH value, oxidant dosage, UV radiation intensity, and pseudo-first-order constant k_obs were systematically studied in both systems. Optimally, the UV/PMS process produced an effluent of higher quality than the UV/H₂O₂, as measured by the removal efficiencies of chemical oxygen demand (COD) in 60 min, which were 48.2 and 64.3% for the respective UV/H₂O₂ and UV/PMS processes and corresponding k_obs values of 0.0102 and 0.0159 min^-1, respectively. Radical scavenging experiments demonstrated that •OH was the primary reactive oxygen species in UV/H₂O₂ process, and •OH and SO₄^-• in the UV/PMS process. Moreover, ultraviolet-visible spectroscopy and gas chromatography coupled mass spectroscopy analyses showed that deep treatment of petroleum hydrocarbons with carbon chain lengths greater than 18 and macromolecular semi-volatile organic compounds in paper wastewater is difficult, whereas the UV/PMS process can significantly improve the removal of amides, esters, phenols, and other aromatic compounds.

Assessment of phytotoxic potential and pathogenic bacteria removal from secondary effluents during ozonation and UV/H2O2

Wastewater reuse is an important strategy for water resource management. For this reason, the disinfection process must be appropriated, eliminating pathogenic microorganisms. Ozonation (O₃) and UV/H₂O₂ treatments can be used for effluent disinfection, but few studies just address the Escherichia coli quantification. In this study, secondary effluents from two wastewater treatment plants with different characteristics were exposed to O₃ (5 and 10 mg L^-1) or UV/H₂O₂ (H₂O₂: 90 mg L^-1) treatments and evaluated by BD Phoenix ™ 100 (Becton Dickinson, USA) and MALDI-TOF for the characterization of the indigenous microorganisms in the effluents, before and after treatments. Additionally, all the samples were tested for phytotoxicity by Lactuca sativa bioassay. The results showed that the highest ozone dose and the UV/H₂O₂ treatment were effective in removing E. coli. UV/H₂O₂ was more efficient as it eliminated most of the microorganisms. Acinetobacter sp., Aeromonas and Pseudomonas were still found after O₃ treatment. Bacillus sp. was found after O₃ and UV/H₂O₂ treatments. The results with L. sativa showed inhibition of root growth for all dry period (low rainfall) samples of one of the WWTP, due to the high concentration of the phytotoxicity compounds. For environmental and human health safety, treated effluents should be evaluated for their toxic and pathogenic potential before being released into the environment. Pathogens evaluation on treated effluents should cover a wider range of pathogenic microorganisms than those routinely required by legislation.

Comprehensive assessment of chemical residues in surface and wastewater using passive sampling, chemical, biological, and fish behavioral assays

Effluents from ten full-scale municipal wastewater treatment plants (WWTPs) that discharge into the Hudson River, surface waters, and wild-caught fish samples were analyzed using liquid chromatography with tandem mass spectrometry (LC/MS/MS) to examine the influence of wastewater discharge on the concentrations of contaminants of emerging concern (CECs) and their ecological impacts on fish. Analysis was based on targeted detection of 41 pharmaceuticals, and non-targeted analysis (suspect screening) of CECs. Biological effects of treated WWTP effluents were assessed using a larval zebrafish (Danio rerio) swimming behavior assay. Concentrations of residues in surface waters were determined in grab samples and polar organic chemical integrative samplers (POCIS). In addition, vitellogenin peptides, used as biomarkers of endocrine disruption, were quantified using LC/MS/MS in the wild-caught fish plasma samples. Overall, 94 chemical residues were identified, including 63 pharmaceuticals, 10 industrial chemicals, and 21 pesticides. Eight targeted pharmaceuticals were detected in 100% of effluent samples with median detections of: bupropion (194 ng/L), carbamazepine (91 ng/L), ciprofloxacin (190 ng/L), citalopram (172 ng/L), desvenlafaxine (667 ng/L), iopamidol (3790 ng/L), primidone (86 ng/L), and venlafaxine (231 ng/L). Over 30 chemical residues were detected in wild-caught fish tissues. Notably, zebrafish larvae exposed to chemical extracts of effluents from 9 of 10 WWTPs, in at least one season, were significantly hyperactive. Vitellogenin expression in male or immature fish occurred 2.8 times more frequently in fish collected from the Hudson River as compared to a reference site receiving no direct effluent input. Due to the low concentrations of pharmaceuticals detected in effluents, it is likely that chemicals other than pharmaceuticals measured are responsible for the behavioral changes observed. The combined use of POCIS and non-target analysis demonstrated significant increase in the chemical coverage for CEC detection, providing a better insight on the impacts of WWTP effluents and agricultural practices on surface water quality.

A systematic review on chlorine tolerance among bacteria and standardization of their assessment protocol in wastewater

Though chlorine is a cost-effective disinfectant for water and wastewaters, the bacteria surviving after chlorination pose serious public health and environmental problems. This review critically assesses the mechanism of chlorine disinfection as described by various researchers; factors affecting chlorination efficacy; and the re-growth potential of microbial contaminations in treated wastewater post chlorination to arrive at meaningful doses for ensuring health safety. Literature analysis shows procedural inconsistencies in the assessment of chlorine tolerant bacteria, making it extremely difficult to compare the tolerance characteristics of different reported tolerant bacteria. A comparison of logarithmic reduction after chlorination and the concentration-time values for prominent pathogens led to the generation of a standard protocol for the assessment of chlorine tolerance. The factors that need to be critically monitored include applied chlorine doses, contact time, determination of chlorine demands of the medium, and the consideration of bacterial counts immediately after chlorination and in post chlorinated samples (regrowth). The protocol devised here appropriately assesses the chlorine-tolerant bacteria and urges the scientific community to report the regrowth characteristics as well. This would increase the confidence in data interpretation that can provide a better understanding of chlorine tolerance in bacteria and aid in formulating strategies for effective chlorination.

Possibilities of Real Time Monitoring of Micropollutants in Wastewater Using Laser-Induced Raman & Fluorescence Spectroscopy (LIRFS) and Artificial Intelligence (AI)

The entire water cycle is contaminated with largely undetected micropollutants, thus jeopardizing wastewater treatment. Currently, monitoring methods that are used by wastewater treatment plants (WWTP) are not able to detect these micropollutants, causing negative effects on aquatic ecosystems and human health. In our case study, we took collective samples around different treatment stages (aeration tank, membrane bioreactor, ozonation) of a WWTP and analyzed them via Deep-UV laser-induced Raman and fluorescence spectroscopy (LIRFS) in combination with a CNN-based AI support. This process allowed us to perform the spectra recognition of selected micropollutants and thus analyze their reliability. The results indicated that the combination of sensitive fluorescence measurements with very specific Raman measurements, supplemented with an artificial intelligence, lead to a high information gain for utilizing it as a monitoring purpose. Laser-induced Raman spectroscopy reaches detections limits of alert pharmaceuticals (carbamazepine, naproxen, tryptophan) in the range of a few µg/L; naproxen is detectable down to 1 × 10−4 mg/g. Furthermore, the monitoring of nitrate after biological treatment using Raman measurements and AI support showed a reliable assignment rate of over 95%. Applying the fluorescence technique seems to be a promising method in observing DOC changes in wastewater, leading to a correlation coefficient of R2 = 0.74 for all samples throughout the purification processes. The results also showed the influence of different extraction points in a cleaning stage; therefore, it would not be sensible to investigate them separately. Nevertheless, the interpretation suffers when many substances interact with one another and influence their optical behavior. In conclusion, the results that are presented in our paper elucidate the use of LIRFS in combination with AI support for online monitoring.

Estrogenic activity and ecological risk of steroids, bisphenol A and phthalates after secondary and tertiary sewage treatment processes

Effluents of sewage treatment plants (STPs) are an important source of estrogenic substances to the receiving water bodies affecting their ecological safety. In this study, steroids, bisphenol A (BPA) and phthalates were assessed in the secondary (SE) and tertiary effluent (TE) of three typical urban STPs in Beijing (China). In addition, the overall estrogenic activity in these effluents was assessed by an in-vitro bioassay (ERE-CALUX). Results showed that the concentrations and activities of estrogenic compounds in TE were lower than those in SE. The residual concentration of 17β-estradiol (E2) was the highest among the detected steroids, accounting for 51.6 ± 5.1% in SE and 57.5 ± 24.8% in TE. The residual level (25.2-41.6 ng/L) of BPA in effluents was significantly higher than that of steroids (0.2-28.8 ng/L). The residual concentration of diethyl phthalate was the highest among the detected phthalates accounting for 47.1 ± 5.1% in SE and 37.6 ± 11.5% in TE. Steroids and BPA had a higher removal rate (83.5% and 96.7%) in secondary and tertiary treatment than phthalates (68.8% and 83.1%). The hydrophobic characteristics of these estrogenic compounds determined the removal mechanism. The removal of steroids, BPA, dimethyl phthalate and diethyl phthalate (LogKow= 1.61-4.15) mainly occurred through biodegradation in the water phase, while the removal of dibutyl phthalate, butylbenzyl phthalate and di(2-ethylhexyl) phthalate (LogKow= 4.27-7.50) mainly occurred in the solid phase after adsorption on and sedimentation of the suspended particulate matter. According to ERE-CALUX, the estrogenic activity in the final STP effluents was 3.2-45.6 ng E2-equivalents/L, which is higher than reported levels in the effluents of European STPs. Calculation of estrogenic equivalents by using substance specific chemical analysis indicated that the dominant contributor was E2 (56.4-88.4%), followed by 17α-ethinylestradiol (EE2) (4.1-34.8%), both also exerting a moderate risk to the aquatic ecosystem. While the upgrade of treatment processes in STPs has efficiently reduced the emission of estrogenic substances, their ecological risk was not yet phased out.

Ozonation of organic compounds in water and wastewater: A critical review

Ozonation has been applied in water treatment for more than a century, first for disinfection, later for oxidation of inorganic and organic pollutants. In recent years, ozone has been increasingly applied for enhanced municipal wastewater treatment for ecosystem protection and for potable water reuse. These applications triggered significant research efforts on the abatement efficiency of organic contaminants and the ensuing formation of transformation products. This endeavor was accompanied by developments in analytical and computational chemistry, which allowed to improve the mechanistic understanding of ozone reactions. This critical review assesses the challenges of ozonation of impaired water qualities such as wastewaters and provides an up-to-date compilation of the recent kinetic and mechanistic findings of ozone reactions with dissolved organic matter, various functional groups (olefins, aromatic compounds, heterocyclic compounds, aliphatic nitrogen-containing compounds, sulfur-containing compounds, hydrocarbons, carbanions, β-diketones) and antibiotic resistance genes.

Towards regulation of Endocrine Disrupting chemicals (EDCs) in water resources using bioassays - A guide to developing a testing strategy

Endocrine disrupting chemicals (EDCs) are found in every environmental medium and are chemically diverse. Their presence in water resources can negatively impact the health of both human and wildlife. Currently, there are no mandatory screening mandates or regulations for EDC levels in complex water samples globally. Bioassays, which allow quantifying in vivo or in vitro biological effects of chemicals are used commonly to assess acute toxicity in water. The existing OECD framework to identify single-compound EDCs offers a set of bioassays that are validated for the Estrogen-, Androgen-, and Thyroid hormones, and for Steroidogenesis pathways (EATS). In this review, we discussed bioassays that could be potentially used to screen EDCs in water resources, including in vivo and in vitro bioassays using invertebrates, fish, amphibians, and/or mammalians species. Strengths and weaknesses of samples preparation for complex water samples are discussed. We also review how to calculate the Effect-Based Trigger values, which could serve as thresholds to determine if a given water sample poses a risk based on existing quality standards. This work aims to assist governments and regulatory agencies in developing a testing strategy towards regulation of EDCs in water resources worldwide. The main recommendations include 1) opting for internationally validated cell reporter in vitro bioassays to reduce animal use & cost; 2) testing for cell viability (a critical parameter) when using in vitro bioassays; and 3) evaluating the recovery of the water sample preparation method selected. This review also highlights future research avenues for the EDC screening revolution (e.g., 3D tissue culture, transgenic animals, OMICs, and Adverse Outcome Pathways (AOPs)).

Evaluation of a full-scale wastewater treatment plant with ozonation and different post-treatments using a broad range of in vitro and in vivo bioassays

Micropollutants present in the effluent of wastewater treatment plants (WWTPs) after biological treatment are largely eliminated by effective advanced technologies such as ozonation. Discharge of contaminants into freshwater ecosystems can thus be minimized, while simultaneously protecting drinking water resources. However, ozonation can lead to reactive and potentially toxic transformation products. To remove these, the Swiss Federal Office for the Environment recommends additional "post-treatment" of ozonated WWTP effluent using sand filtration, but other treatments may be similarly effective. In this study, 48 h composite wastewater samples were collected before and after full-scale ozonation, and after post-treatments (full-scale sand filtration, pilot-scale fresh and pre-loaded granular activated carbon, and fixed and moving beds). Ecotoxicological tests were performed to quantify the changes in water quality following different treatment steps. These included standard in vitro bioassays for the detection of endocrine, genotoxic and mutagenic effects, as well as toxicity to green algae and bacteria, and flow-through in vivo bioassays using oligochaetes and early life stages of rainbow trout. Results show that ozonation reduced a number of ecotoxicological effects of biologically treated wastewater by 66 - 93%: It improved growth and photosynthesis of green algae, decreased toxicity to luminescent bacteria, reduced concentrations of hormonally active contaminants and significantly changed expression of biomarker genes in rainbow trout liver. Bioassay results showed that ozonation did not produce problematic levels of reaction products overall. Small increases in toxicity observed in a few samples were reduced or eliminated by post-treatments. However, only relatively fresh granular activated carbon (analyzed at 13,000 - 20,000 bed volumes) significantly reduced effects additionally (by up to 66%) compared to ozonation alone. Inhibition of algal photosynthesis, rainbow trout liver histopathology and biomarker gene expression proved to be sufficiently sensitive endpoints to detect the change in water quality achieved by post-treatment.

Bromide strongly influences the formation of reaction products during the ozonation of diclofenac, metoprolol and isoproturon

Bromide as an omnipresent matrix component in wastewater can react with ozone to form hypobromous acid (HOBr). This secondary oxidant can subsequently react with micropollutants but also with formed intermediates. Therefore, bromide and especially HOBr can highly influence the formation of transformation products (TPs). This has already been reported for the ozonation of N,N-dimethylsulfamide leading to the formation of the cancerogenic N-nitrosodimethylamine only in bromide containing waters. In this study, the influence of different bromide and ozone concentrations on the formation of TPs during the ozonation of isoproturon (ISO), metoprolol (METO) and diclofenac (DCF) were investigated. Additionally, TPs were identified, which are formed in the direct reaction of the micropollutants with HOBr with and without subsequent ozonation. The results showed that even if the reactions of ozone with the substances should be favored bromide can highly influence the formation of TPs already at low concentrations. In summary, new TPs after the reaction with HOBr (and subsequent ozonation) could be postulated for ISO, METO and DCF. This underlines that the present water matrix can have a high influence on the formation of TPs and that these mechanisms need to be investigated further.

Production of Plant Proteases and New Biotechnological Applications: An Updated Review

An updated review of emerging plant proteases with potential biotechnological application is presented. Plant proteases show comparable or even greater performance than animal or microbial proteases for by-product valorization through hydrolysis for, for example, cheese whey, bird feathers, collagen, keratinous materials, gelatin, fish protein, and soy protein. Active biopeptides can be obtained as high added value products, which have shown numerous beneficial effects on human health. Plant proteases can also be used for wastewater treatment. The production of new plant proteases is encouraged for the following advantages: low cost of isolation using simple procedures, remarkable stability over a wide range of operating conditions (temperature, pH, salinity, and organic solvents), substantial affinity to a broad variety of substrates, and possibility of immobilization. Vegetable proteases have enormous application potential for the valorization of industrial waste and its conversion into products with high added value through low-cost processes.

Road Runoff Characterization: Ecotoxicological Assessment Combined with (Non-)Target Screenings of Micropollutants for the Identification of Relevant Toxicants in the Dissolved Phase

Road runoff (RR) is an important vector of micropollutants towards groundwater and soils, threatening the environment and ecosystems. Through combined chemical and biological approaches, the purpose of this study was to get insights on specific toxicants present in RR from two sites differing by their traffic intensity and their toxicological risk assessment. Non-target screening was performed by HRMS on RR dissolved phase. Ecotoxicological risk was evaluated in a zebrafish embryos model and on rat liver mitochondrial respiratory chain. Specific HRMS fingerprints were obtained for each site, reflecting their respective traffic intensities. Several micropollutants, including 1,3-diphenylguanidine (DPG) and benzotriazole (BZT) were identified in greater concentrations at the high-traffic site. The origin of DPG was confirmed by analyzing HRMS fingerprints from shredded tires. RR samples from each site, DPG and BZT were of relatively low toxicity (no mortality) to zebrafish embryos, but all generated distinct and marked stress responses in the light–dark transition test, while DPG/BZT mixes abolished this effect. The moderate-traffic RR and DPG inhibited mitochondrial complex I. Our study highlights (i) the unpredictability of pollutants cocktail effect and (ii) the importance of a multi-approaches strategy to characterize environmental matrices, essential for their management at the source and optimization of depollution devices.

A zero-valent iron and zeolite filter for nitrate recycling from agricultural drainage water

Nitrate reduction to ammonium followed by ammonium capture and reuse, represent a new pathway to recycle nitrogen, prevent eutrophication, and to save energy used for industrial ammonium production. The present study investigates the principle of nitrogen recycling to agricultural drainage water using a coupled zero-valent iron (ZVI) and zeolite-based filter column system tested in laboratory and field continuous-flow experiments. A 40-day laboratory test showed 82% nitrate removal, of which 70% was converted to ammonium. In the following pilot scale field test, a total of 59.2 m³ (1700 pore volumes) drainage water with a nitrate concentration of 2-8 mg L^-1 NO₃^--N was filtrated. An oxidizing unit inserted after the ZVI unit removed iron(II) and optimized ammonium retention in the zeolite unit. Nitrate removal efficiency was 94% for the entire 56-day period with a slight pH increase (pH 8.9). All ammonium produced was retained by the zeolite unit. Formation of green rust carbonate (layered Fe^II-Fe^III-hydroxide) was observed on ZVI particle surfaces, which may increase the redox capacity of the filter system by up to 50% and contribute to its cost-efficiency. Moreover, all phosphate in the influent waters with concentrations between 0.1 and 0.5 mg L^-1 was retained due to sorption by iron oxides in the system. Corrosion products formed cause partial filter clogging and should be removed by regular cleaning and backflushing. In conclusion, the ZVI - zeolite coupled filter system serves as a promising and cost-effective technology for nutrient removal and ammonium retention from agricultural drainage water.

Modification of cyclodextrin and use in environmental applications

Water pollution, which has become a global problem in parallel with environmental pollution, is a problem that needs to be solved urgently, considering the gradual depletion of water resources. The inadequacy of the water treatment methods and the materials used somehow directed the researchers to look for dual character structures such as biocompatible and biodegradable β-cyclodextrin (β-CD). β-CD, which is normally insoluble in water, is used in demanding wastewater applications by being modified with the help of different agents to be water soluble or transformed into polymeric adsorbents as a result of co-polymerization via cross-linkers. In this way, in addition to the host-guest interactions offered by β-CD, secondary forces arising from these interactions provide advantages in terms of regeneration and reusability. However, the adsorption efficiency and synthesis steps need to be improved. Based on the current studies presented in this review, in which cross-linkers and modification methods are also mentioned, suggestions for novel synthesis methods of new-generation β-CD-based materials, criticisms, and recent methods of removal of micropollutants such as heavy metals, industrial dyes, harmful biomolecules, and pharmaceutics wastes are mentioned.

Chemically induced oxidative stress improved bacterial laccase-mediated degradation and detoxification of the synthetic dyes

To alleviate the risk of textile effluent, the development of highly effective bioremediation strategies for synthetic dye removal is needed. Herein, we aimed to assess whether intensified bioactivity of Bacillus pumilus ZB1 by oxidative stress could improve the removal of textile dyes. Methyl methanesulfonate (MMS) induced oxidative stress significantly promoted laccase expression of B. pumilus ZB1. Both the level of hydrogen dioxide and superoxide anion showed a significant positive correlation with laccase activity (RSQ = 0.963 and 0.916, respectively) along with the change of MMS concentration. The regulation of laccase expression was closely related to oxidative stress. The overexpressed laccase in the supernatant improved the decolorization of synthetic dyes (16.43% for Congo Red, 54.05% for Crystal Violet, and 41.61% for Reactive Blue 4). Laccase was subsequently expressed in E. coli. Investigation of the potential of bacterial laccase in dye remediation using Congo Red showed that an effective degradation of azo dye could be achieved with laccase treatment. Laccase remediation alleviated the cytotoxicity of Congo Red to human hepatocytes. In silico study identified eight amino acid residues of laccase involved in binding with Congo Red. Overall, regulation of oxidative stress towards bacterium can be used as a promising approach for the improvement of bacterial bioactivity in synthetic dye remediation.

Oxidation of 51 micropollutants during drinking water ozonation: Formation of transformation products and their fate during biological post-filtration

Micropollutants (MP) with varying ozone-reactive moieties were spiked to lake water in the influent of a drinking water pilot plant consisting of an ozonation followed by a biological sand filtration. During ozonation, 227 transformation products (OTPs) from 39 of the spiked 51 MPs were detected after solid phase extraction by liquid chromatography high-resolution mass spectrometry (LC-HRMS/MS). Based on the MS/MS data, tentative molecular structures are proposed. Reaction mechanisms for the formation of a large number of OTPs are suggested by combination of the kinetics of formation and abatement and state-of-the-art knowledge on ozone and hydroxyl radical chemistry. OTPs forming as primary or higher generation products from the oxidation of MPs could be differentiated. However, some expected products from the reactions of ozone with activated aromatic compounds and olefins were not detected with the applied analytical procedure. 187 OTPs were present in the sand filtration in sufficiently high concentrations to elucidate their fate in this treatment step. 35 of these OTPs (19%) were abated in the sand filtration step, most likely due to biodegradation. Only 24 (13%) of the OTPs were abated more efficiently than the parent compounds, with a dependency on the functional group of the parent MPs and OTPs. Overall, this study provides evidence, that the common assumption that OTPs are easily abated in biological post-treatment is not generally valid. Nevertheless, it is unknown how the OTPs, which escaped detection, would have behaved in the biological post-treatment.

Disinfection Byproduct Recovery during Extraction and Concentration in Preparation for Chemical Analyses or Toxicity Assays

Over 700 disinfection byproducts (DBPs) have been identified, but they account for only ∼30% of total organic halogen (TOX). Extracting disinfected water is necessary to assess the overall toxicity of both known and unknown DBPs. Commonly used DBP extraction methods include liquid-liquid extraction (LLE) and solid-phase extraction (SPE), which may use either XAD resins or other polymeric sorbents. With few exceptions, DBP recoveries have not been quantified. We compared recoveries by LLE, XAD resins, and a mixture of Phenomenex Sepra SPE sorbents (hereafter SPE) for (semi-)volatile DBPs and nonvolatile model compounds at the 1-L scale. We scaled up the three methods to extract DBPs in 10 L of chlorinated creek waters. For (semi-)volatile DBPs, XAD resulted in lower recoveries than LLE and SPE at both 1- and 10-L scales. At the 10-L scale, recovery of certain trihalomethanes and trihalogenated haloacetic acids by XAD was negligible, while recovery of other (semi-)volatile DBPs extracted by XAD (<30%) was lower than by SPE or LLE (30-60%). TOX recovery at the 10-L scale was generally similar by the three extraction methods. The low TOX recovery (<30%) indicates that the toxicity assessed by bioassays predominantly reflects the contribution of the nonvolatile, hydrophobic fraction of DBPs.

Differences in marine megafauna in vitro sensitivity highlights the need for species-specific chemical risk assessments

Sea turtles, dolphins and dugongs can be exposed to large mixtures of contaminants due to the proximity of foraging locations to anthropogenic inputs. Differences in accumulation and effect result in differences of chemical risk to these species. However, little is known about the effect of contaminants in marine wildlife. Cell-based, or in vitro, exposure experiments offer an ethical alternative to investigate the effect of contaminants in wildlife. Data from in vitro studies can then be placed in an environmental context, by using screening risk assessments, comparing effect data with accumulation data from the literature, to identify risk to populations of marine wildlife. Cytotoxicity of Cr⁶⁺, Cd²⁺, Hg²⁺, 4,4'-DDE, and PFNA were investigated in primary skin fibroblasts of green turtles, loggerhead turtles, hawksbill turtles, dugongs, Burrunan dolphins, and common bottlenose dolphins. The general order of toxicity for all species was Hg²⁺> Cr⁶⁺ > Cd²⁺> 4,4'-DDE > PFNA, and significant differences in cytotoxicity were found between species for Cr⁶⁺, Cd²⁺ and PFNA. For Cd²⁺, in particular, cells from turtle species were less sensitive than mammalian species, and dugong cells were by far the most sensitive. The results from the cytotoxicity assay were then used in combination with published data on tissue contaminant concentrations to calculate risk quotients for identifying populations of each species most at risk from these chemicals. Cr, Cd and Hg were identified as posing risk in all six species. Dugongs were particularly at risk from Cd accumulation and dolphin species were particularly at risk from Hg accumulation. These results demonstrate the importance of using species-specific effect and accumulation data for developing chemical risk assessments and can be used to inform managers of priority contaminants, species, or populations. Development of additional in vitro endpoints, and improving links between in vitro and in vivo effects, would further improve this approach to understanding chemical risk in marine megafauna.

Potential toxicity of leachate from the municipal landfill in view of the possibility of their migration to the environment through infiltration into groundwater

Leachate from landfills is a product of complex biological and physicochemical processes occurring during waste storage. In the present study, the toxicity of landfill leachate (LL) to human and bacterial cells was investigated for better understanding of LL environmental toxicity. Studies regarding LL physicochemical properties and cytotoxicity analysis were conducted. In Escherichia coli, Pseudomonas fluorescens, Bacillus subtilis, fibroblasts and melanoma A-375 cells, cell viability assays were applied. For the determination of LL antibacterial activity, twofold dilution series of LL were prepared in the range from 50% to 0.1% (50%, 25%, 12.5%, 6.25%, 3.13%, 1.56%, 0.78%, 0.39%, 0.2%, 0.1%). Human cells viability was examined at LL concentrations of 0.1%, 0.5%, 1%, 1.5%, 2%, 2.5%, 5%, 10%, 15%, 20% and 30%. ROS (reactive oxygen species) content and apoptosis level were also measured in bacterial and human cells under the influence of LL. Unexpectedly obtained results indicate stimulation of bacterial viability by LL. Fibroblasts under the influence of LL showed decrease in their viability and increase in apoptosis level and A-375 melanoma cells showed an increase in relative viability and decrease in apoptosis. ROS level in bacterial cells was elevated in higher LL concentrations and decreased in lower LL concentrations. In human cells, ROS content was rather high in both tested cell lines. Presented results indicate cytotoxic potential of analyzed LL and the necessity of LL monitoring because it may pose a health hazard for exposed human populations and the whole human environment.

Ozonation products from trace organic chemicals in municipal wastewater and from metformin: peering through the keyhole with supercritical fluid chromatography-mass spectrometry

Ozonation is an important process to further reduce the trace organic chemicals (TrOCs) in treated municipal wastewater before discharge into surface waters, and is expected to form products that are more oxidized and more polar than their parent compounds. Many of these ozonation products (OPs) are biodegradable and thus removed by post-treatment (e.g., aldehydes). Most studies on OPs of TrOCs in wastewater rely on reversed-phase liquid chromatography- mass spectrometry (RPLC-MS), which is not suited for highly polar analytes. In this study, supercritical fluid chromatography combined with high resolution MS (SFC-HRMS) was applied in comparison to the generic RPLC-HRMS to search for OPs in ozonated wastewater treatment plant effluent at pilot-scale. While comparable results were obtained from these two techniques during suspect screenings for known OPs, a total of 23 OPs were only observed by SFC-HRMS via non-targeted screening. Several SFC-only OPs were proposed as the derivatives of methoxymethylmelamines, phenolic sulfates/sulfonates, and metformin; the latter was confirmed by laboratory-scale ozonation experiments. A complete ozonation pathway of metformin, a widespread and extremely hydrophilic TrOC in aquatic environment, was elaborated based on SFC-HRMS analysis. Five of the 10 metformin OPs are reported for the first time in this study. Three different dual-media filters were compared as post-treatments, and a combination of sand/anthracite and fresh post-granular activated carbon proved most effective in OPs removal due to the additional adsorption capacity. However, six SFC-only OPs, two of which originating from metformin, appeared to be persistent during all post-treatments, raising concerns on their occurrence in drinking water sources impacted by wastewater.

New insight into increased toxicity during ozonation of chlorophenol: The significant contribution of oxidizing intermediates

Biological safety evaluation and toxic by-products identification are critical issues in the partial oxidation process. Previous studies have shown that the whole toxicity increased in the effluent of an ozonation process for chlorophenols removal. Here, this study systematically investigated the changes of acute toxicity during the ozonation of 3-chlorophenol under four key operational conditions, including initial 3-chlorophenol concentration (20-60 mg/L), ozone concentration (14-42 mg/L), reaction pH (3-10) and ozonation time (0-50 min). The results found that the ozonation process induced a significant increase in the acute toxicity, followed by its gradual decrease. The observation of higher acute toxicity increase generally happened at higher initial 3-chlorophenol concentration, lower ozone concentration and lower reaction pH. At the toxicity peaks, the oxidizing intermediates posed acute toxicity equal to 65.8%-96.3% of the whole toxicity. Among them, free active chlorine (FAC) contributed 21.4%-51.6%, and its concentrations significantly correlated to the acute toxicity change. Therefore, two possible FAC generation pathways initiated by ozone molecule were proposed: (i) bond breaking of the oxychloride complex formed by the combination of chloride ion and zwitterion; or (ii) hydrolysis of ozonides formed by the electrophilic reaction of ozone molecule. Together, these results firstly revealed the significant toxicity contribution of oxidizing intermediates during the ozonation of chlorophenols, supporting further development of safe and effective ozone-based water treatment schemes.