Modeling the transport of sodium dodecyl benzene sulfonate in riverine sediment in the presence of multi-walled carbon nanotubes

Photoaged tire wear particles hinder the transport of Pb(II) in urban soils under acid rain: Experimental and numerical investigations

Rapid urbanization brought lots of serious environmental contamination, including the accumulation of heavy metals, acid rain, and the emission of tire wear particles (TWPs), with detrimental effects for terrestrial ecosystems. Nevertheless, how naturally aged TWPs affect the mobilization of heavy metals in soils under acid rain is still unclear. Here, we investigate the adsorption and transport mechanisms of Pb(II) co-existing with acid rainwater in soil-TWP mixtures via batch experiments, column experiments and modeling. Results showed that photoaged TWP significantly prolonged the Pb(II) adsorption equilibrium time (1 to 16 h) and enhanced the Pb(II) adsorption capacity of soils. Soil column profiles confirmed that TWP effectively boosted the initial accumulation of lead in the topsoil and thus impeded the downward transport of lead. The retardation factor (R) estimated by the linear two-site sorption model (TSM) fitting the Pb(II) breakthrough curves gradually increased from 1.098 to 16.38 in soils with TWP (0-10 %). Comparative results of linear or nonlinear TSM suggested nonlinear sorption replacing linear sorption as the main Pb(II) sorption mechanism under 1 % and 10 % TWP. This research provides significant insights into the implications of TWP on the Pb(II) retention behaviors and highlights the severer potential remobilization risks of Pb(II) in urban soils under different acid rain environments.

Enhanced removal of antibiotics and heavy metals in aquatic systems using spent mushroom substrate-derived biochar integrated with Herbaspirillum huttiense

A novel integrated removal strategy was developed to enhance the concurrent elimination of copper (Cu), zinc (Zn), oxytetracycline (OTC), and enrofloxacin (ENR) from the aqueous environments. The underlying adsorption mechanisms of spent mushroom substrate (SMSB) and the Herbaspirillum huttiense strain (HHS1), and their efficacy in removing Cu, Zn, OTC, and ENR was also examined. Results showed that the SMSB-HHS1 composite stabilized 29.86% of Cu and 49.75% of Zn and achieved removal rates of 97.95% for OTC and 59.35% for ENR through a combination of chemisorption and biodegradation. Zinc did not affect Cu adsorption, and ENR did not impact the adsorption of OTC on SMSB. However, the co-presence of OTC and ENR modified the adsorption behaviors of both Cu and Zn. Copper and Zn enhanced the adsorption of OTC and ENR by serving as bridging agents, facilitating the interaction between the contaminants and SMSB. Conversely, OTC and ENR inhibited the adsorption process of Cu by obstructing its interaction with the SMSB and occupying the oxygen-containing functional groups. The ‒OH (3415 cm-1) and C-O-C (1059 cm-1) functional groups were identified as the principal active sites to form hydrogen bonds and interact with Cu and Zn, leading to the formation of CuP4O11 and Zn4CO3(OH)6H2O. HHS1 also enhanced antibiotic removal through biodegradation, as evidenced by the decrease of ‒C‒O and increase of ‒C = O groups. This study underscores the innovative potential of the SMSB-HHS1 composite, offering a sustainable approach to addressing multifaceted pollution challenges in the aquatic environments.

Transport and retention of ciprofloxacin with presence of multi-walled carbon nanotubes in the saturated porous media: impacts of ionic strength and cation types

The environmental fate and risks of ciprofloxacin (CIP) in the subsurface have raised intensive concerns. Herein, the transport behaviors of CIP in both saturated quartz sand and sand/multi-walled carbon nanotubes (MWCNTs) mixtures under different solution ionic strength of the solution and coexisting cation types were investigated. Batch adsorption experiments highlighted growing adsorptive capacity for CIP with the increasing content of MWCNTs in the MWCNTs-quartz sand mixtures (from 0.5% to 1.5%, w/w). Breakthrough curves (BTCs) of CIP in the MWCNTs-quartz sand mixtures were well fitted by the two-site chemical nonequilibrium model (R2 > 0.833). The estimated retardation factors for CIP increased from 9.68 to 282 with growing content of MWCNTs in the sand column, suggesting the presence of MWCNTs significantly inhibited the transport of CIP in saturated porous media. Moreover, the values of retardation factors are negatively correlated with the ionic strength and higher ionic strength could facilitate the transport of CIP in the saturated porous media. Compared with monovalent cations (Na+), the presence of divalent cations (Ca2+) significantly facilitated the transport of CIP in the columns due to the complexation between CIP and Ca2+ as well as deposition of MWCNTs aggregates on the sand surface. Results regarding CIP retention in columns indicated that MWCNTs could enhance the accumulation of CIP in the layers close to the influent of sand columns, while they could hinder upward transport of CIP to the effluent. This study improves our understanding for transport behaviors and environmental risk assessments of CIP in the saturated porous media with MWCNTs.

Transport of nZVI/copper synthesized by green tea extract in Cr(IV)-contaminated soil: modeling study and reduced toxicity

In this study, nano-zero-valent iron/copper was synthesized by green tea extracts (GT-nZVI/Cu) and produced a stable suspension than nano-zero-valent iron synthesized by green tea extracts (GT-nZVI) injected into Cr(VI)-containing soil column. The equilibrium 1D-CDE model was successfully used to fit the penetration curves of Fe(tot), Fe(aq), and Fe(0) in order to determine the relevant parameters. The hydrodynamic dispersion coefficient of chromium-contaminated soil was 0.401 cm2·h-1, and the pore flow rate was 0.144 cm·h-1. The stable C/C0 of Fe(tot), Fe(aq), and Fe(0) in the effluent were retarded to 0.39, 0.79, and 0.11, respectively, compared to a ratio of 1 for the concentration of the tracer Cl- in the effluent to the concentration in the influent. Additionally, the 1D-CDE model describes the migration behavior of Cr(VI) with a high R2 (> 0.97). The obtained blocking coefficients declined gradually with increasing concentration of GT-nZVI/Cu suspension and decreasing concentration of Cr(VI). The content of reduced chromium in the soil decreased from 2.986 to 1.121 after remediation, while the content of more stable oxidizable chromium and residual chromium increased from 2.975 and 20.021 to 16.471 and 27.612. The phytotoxicity test showed that mung bean seeds still had a germination rate of 90% (control of 100%), root length of 29.63 mm (control of 35.25 mm), and stem length of 17.9 cm (control of 18.96 cm) after remediation with GT-nZVI/Cu. These indicated that GT-nZVI/Cu was effective in immobilizing Cr(VI) in the soil column and reduced the ecological threat. This study provides an analytical basis and theoretical model for the migration of chromium-contaminated soil in practical application.

Preparation of carbon-rich material from Dendrobium officinale polysaccharide in deep eutectic system

A carbon-rich material (DESysChar) was prepared from polysaccharide within a deep eutectic system (DESys) containing oxalic acid, and systematically characterized using various analytical techniques. The investigation of reaction mechanism revealed concurrent dehydration and etherification processes. This study commenced with the extraction of plant polysaccharide using the DESys-based mechanochemical extraction method from Dendrobium officinale. Subsequently, the DESys method was used to carbonize the extracted Dendrobium officinale polysaccharide and produce DESysChar. DESysChar was then used for the adsorption and determination of pollutants in water. This study represents a significant advancement in eco-friendly material synthesis, enabling the low-temperature (120 °C) carbonization of plant-derived polysaccharides, thereby reducing energy consumption and environmental impact. The effective adsorption of methylene blue by DESysChar underscores its potential in environmental remediation. This study presents a more responsible and efficient approach to polysaccharide extraction and carbonization, addressing environmental concerns. Embracing the 4S workflow (involving Sustainable raw materials converted into Sustainable degradable products, by using Sustainable technology throughout the process to create a Sustainable environment) promotes sustainability in material development, laying the foundation for future eco-friendly practices in various industries. In summary, this study propels sustainable polysaccharide development for widespread use.

Synthesizing sulfhydryl-functionalized biochar for effectively removing mercury ions from contaminated water

Biochar is regarded as an effective adsorbent for heavy metal pollution treatment, and functional optimization is still needed to improve its performance. We created raw biochar (BC and BP) from corn straw and pine sawdust, which were modified to produce sulfhydryl-modified biochar (MBC and MBP). Isothermal adsorption experiments and adsorption kinetics experiments as well as the related model fitting were performed to evaluate the adsorption performance of biochar on Hg(II). According to the results of the Langmuir model fitting, the maximum adsorption capacities of sulfhydryl-modified biochar were 193.05 mg/g (MBC) and 178.04 mg/g (MBP), respectively, which were approximately 1.6 times higher than the raw biochar. The results showed that adding sulfhydryl groups to biochar can improve its adsorption performance. The prompt effect resulted from the sulfhydryl modification providing additional functional groups and enhanced chemisorption and physical adsorption properties.

Unveiling the roles of dissolved organic matters derived from different biochar in biochar/persulfate system: Mechanism and toxicity

Biochar has been frequently used as a persulfate (PS) activator due to its attractive properties, but dissolved organic matter (DOM) derived from the non‑carbonized part of biochar has received less attention, not to mention its specific role and impact in biochar/PS systems. In this study, wheat straw, municipal sludge, and swine bone were selected as the representative feed stocks of biochar. Subsequently, these three types of biochar were adopted to explore the roles of DOM in biochar/PS systems. Although the composition and amount of DOM derived from different biochar were discrepant, they exhibited similar effect in biochar/PS systems. To be specific, the pore-clogging effect of DOM on biochar suppressed the adsorption capacity and catalytic performance of the three biochar. Furthermore, the removal of DOM decreased the environmental risk of these biochar/PS systems and enhanced the stability of the involved biochar. With respect to the variation in degradation mechanism, the removal of DOM increased the proportion of electron transfer pathway in unison, but the diminution in the roles of O₂^•¯ and ¹O₂ was more remarkable in bone-derived-biochar/PS systems. Additionally, the toxicity test illustrated that the leakage and accumulation of DOM were toxic to Chlorella sp., and the DOM from sludge-derived-biochar presented the highest toxicity. Overall, this study analyzes the roles of DOM derived from different biochar in biochar/PS systems and evaluates their environmental risk, which contributes to a comprehensive understanding of the fate of DOM derived from biochar.

Efficient degradation of tetracycline under the conditions of high-salt and coexisting substances by magnetic CuFe2O4/g-C3N4 photo-Fenton process

For the effective degradation of tetracycline (TC), a facilely prepared magnetic CuFe₂O₄/g-C₃N₄ (CFO/g) photocatalyst was successfully constructed. The structure, morphology, composition, optical, and magnetic properties of CFO/g were characterized. CFO/g demonstrated excellent photo-Fenton performance of TC in the presence of high-Cl^-, NO₃^-, HCO₃^-, HPO₄^2-, SO₄^2- and humic acid. Ten cycles of experiments with the removal rate of TC only decreasing by 2.8% confirmed the stability and high activity of CFO/g. The dissolved concentrations of Fe and Cu ions were 0.013 and 0.009 mg L^-1, respectively. Its excellent magnetic properties made CFO/g easier to be recycled than traditional catalysts. ·OH and O₂·^- were proposed to be the main active species in the photo-Fenton system. The CFO/g heterojunction enhanced the separation of photogenerated electron-hole pairs and visible light absorption range. Furthermore, the identification of intermediates suggested that TC degradation was classified into two pathways, and the most critical and rapid degradation was achieved within the first 30 min. The TC and its intermediates did not significantly inhibit the growth activity of Escherichia coli. This research provided a promising application of magnetic photocatalysts in wastewater treatment of pharmaceuticals and personal care products.

The role of microplastics in altering arsenic fractionation and microbial community structures in arsenic-contaminated riverine sediments

The ability of microplastics (MPs) to interact with environmental pollutants is of great concern. Riverine sediments, as sinks for multi-pollutants, have been rarely studied for MPs risk evaluation. Meanwhile, MPs generated from biodegradable plastics are questioning the safety of the promising materials. In this study, we investigated the effects of typical non-degradable polyethylene (PE) and biodegradable polylactic acid (PLA) MPs on sediment enzymes, arsenic (As) fractionation, and microbial community structures in As-contaminated riverine sediments. The results indicated that the presence of MPs (1% and 3%, w/w) led As transformed into more labile and bioavailable fractions in riverine sediments, especially under higher As and MPs levels. Analysis on microbial activities and community structures confirmed the strong potential of MPs in inhibiting microbial activities and shifting bacterial community succession patterns through enrichment of certain microbiota. Moreover, biodegradable PLA MPs presented stronger alterations in arsenic fractionation and microbial community structures than PE MPs did, which might be jointly attributed to adsorption behaviors, microbial alterations, and potential PLA degradation behaviors. The study indicated that MPs contamination increased As mobility and bioavailability, and shifted microbial communities in riverine sediments. Moreover, biodegradable MPs might lead to stronger microbial alterations and increases in As bioavailability, acting as a threat to ecological safety, which needed further exploration.

Effects of biochar-based materials on the bioavailability of soil organic pollutants and their biological impacts

Motivated by the unique structure and superior properties, biochar-based materials, including pristine biochar and composites of biochar with other functional materials, are considered as new generation materials for diverse multi-functional applications, which may be intentionally or unintentionally released to soil. The influencing mechanism of biochar-based material on soil organisms is a key aspect for quantifying and predicting its benefits and trade-offs. This work focuses on the effects of biochar-based materials on soil organisms within the past ten years. 206 sources are reviewed and available knowledge on biochar-based materials' impacts on soil organisms is summarized from a diverse perspective, including the pollutant bioavailability changes in soil, and potential effects of biochar-based materials on soil organisms. Herein, effects of biochar-based materials on the bioavailability of soil organic pollutants are detailed, from the perspective of plant, microorganism, and soil fauna. Potential biological effects of pristine biochar (PBC), metal/metal compounds-biochar composites (MBC), clay minerals-biochar composites (CMBC), and carbonaceous materials-biochar composites (CBC) on soil organisms are highlighted for the first time. And possible mechanisms are presented based on the different characters of biochar-based materials as well as various environmental interactions. Finally, the bottleneck and challenges of risk assessment of biochar-based materials as well as future prospects are proposed. This work not only promotes the development of risk assessment system of biochar-based materials, but broadens the strategy for the design and optimization of environmental-friendly biochar materials.

Enhanced remediation of Cd-contaminated soil using electrokinetic assisted by permeable reactive barrier with lanthanum-based biochar composite filling materials

Electrokinetic remediation (EK) combined with a permeable reactive barrier (PRB) is a relatively new technique for efficiently remediating Cd-contaminated soil in situ. Eupatorium adenophorum, which is a malignant invasive plant, was used to synthesise biochar and a novel lanthanum-based biochar composite (LaC). The biochar and LaC were used as cheap and environmentally benign PRB filling materials to remediate simulated and real Cd-contaminated soils. The pH and residual Cd concentration in the simulated contaminated soil during remediation gradually increased from the anode to the cathode used to apply an electric field to the EK-PRB system. However, the soil conductivity changed in the opposite way, and the current density first increased and then decreased. For simulated contaminated soils with initial Cd concentrations of 34.9 and 100.6 mg kg^-1, the mean Cd removal rates achieved using LaC were 90.6% and 89.3%, respectively, which were significantly higher than those of biochar (P < 0.05). Similar results were achieved using natural soils from mining area and polluted farmland, and the Cd removal rates were 66.9% and 72.0%, respectively. Fourier-transform infrared and X-ray photoelectron spectroscopy indicated that there were many functional groups on the LaC surfaces. The removal mechanism of EK-PRB for Cd in contaminated soil includes electromigration, electroosmotic flow, surface adsorption, and ion exchange. The results indicated that the LaC could be used in the EK-PRB technique as a cheap and 'green' material to efficiently decontaminate soil polluted with heavy metals.

Effects of biochar on transport and retention of phosphorus in porous media: Laboratory test and modeling

Given the complexity of soil components, a detailed understanding of the effects of single factors on phosphorus transport and retention will play a key role in understanding the environmental effects of phosphorus. In this work, quartz sand columns (considering five factors: doping rate, pH, particle size, ionic strength and cation type), combined with a two-site nonequilibrium transport model (TSM), were used to investigate phosphate (P) transport behavior. The results show that changes in doping ratio (0.4%-1.6%) and pH (5-9) have a notable effect on the transport of P, while, particle size of quartz sand hardly impacts the transport. When biochar was added at 1.6%, the surface of biochar increased the P fixation rate by about 37% through direct interaction with phosphate and bridging action with metal ions. As the morphology of P changed under different pH conditions, a part of P was immobilized in the form of precipitation. The immobilization of P was further enhanced with the increase of ionic strength. Compared with the direct interaction of P with biochar in Na⁺ solution, Ca²⁺ and Mg²⁺ solutions are more likely to adsorb P. Meanwhile, the TSM model also fits the transport behavior well. This study provides a perspective for evaluating the environmental behavior of P in the porous media interaction with biochar.

Sustainable materials in the removal of pesticides from contaminated water: Perspective on macro to nanoscale cellulose

Recently, over utilization of pesticides in agrarian and non- agrarian sectors has resulted in a significant increment in the deposition of their remnants in different segments of the environmental media. The presence of pesticides and transportation of their different metabolites in rivers, ponds, lakes, soils, air, groundwater sources and drinkable water sources has demonstrated a high threat to human wellbeing and the climate. Thus, the removal of pesticides and their metabolites from contaminated water is imperative to lessen the ill effects of pesticides on human beings. In the present article, we have appraised recent advances in pesticides removal utilizing low cost pristine and functionalized cellulose biomass-based derivatives. One of the key focus has been on better understand the destiny of pesticides in the environment as well as their behaviour in the water. In addition, the impact of magnetite cellulose nanocomposites, cellulose derived photo nano-catalyst, cellulose/clay nano composites, CdS/cellulose nanocomposites and activated carbons/biochar on percent removal of pesticides have also been a part of the current review. The impact of different parameters such as adsorbent dosage, pH, time of contact and initials pesticide concentration on adsorption capacity and adsorption kinetics followed during absorption by different cellulosic bio-adsorbents has also been given. The cellulosic biomass is highly efficient in the removal of pesticides and their efficiency further increases upon functionalization or their conversion into activated carbons forms. Nano particles loaded cellulosic materials have in general found to be less efficient than raw, functionalized cellulosic materials and activated carbons. Further, among different nano particles loaded with cellulose-based materials, cellulose/MnO₂ photonanocatalyst were noticed to be more effective. So considerable efforts should be given to determine the finest practices that relate to the dissipation of different pesticides from the water.

Effects of virgin microplastics on the transport of Cd (II) in Xiangjiang River sediment

River sediments are considered as sinks of microplastics (MPs). Although numerous studies have been conducted on MPs pollution in river sediments, the impact of MPs on the environmental behavior of Cd (II) in river sediments is still unknown. In this work, the effects of six MPs (polyethylene, polypropylene, polystyrene, polyvinyl chloride, polymethyl methacrylate and polylactic acid) on the adsorption of Cd (II) by Xiangjiang River sediment and the transport of Cd (II) in sediment were studied. The results showed that the adsorption ability of sediment to Cd (II) decreased with the increase of the content of MPs in sediment. When the content of MPs in sediment increased to 10%, polypropylene had the greatest effect on the adsorption affinity of sediments to Cd (II). Moreover, the addition of MPs accelerated transport of Cd (II) in sediment, and the transport of Cd (II) in sediment increased with the increase of the content of MPs. The reason may be that after adding MPs, the adsorption capacity of sediment to Cd (II) decreases, and the mass transfer resistance of Cd (II) to sediment reduces, which leads to faster transport of Cd (II) in sediment. Especially, when the content of MPs in sediment increased to 10% (w/w), the saturation point of the breakthrough curve decreased by about 70 pore volumes. This work hopes to provide helpful views on the environmental behavior and risk assessment of Cd (II) in the presence of MPs.

Phosphorus transport in different soil types and the contribution of control factors to phosphorus retardation

Iron (Fe) minerals, organic matter (OM), and pH can effectively regulate phosphorus (P) transport in the soil. However, their respective contributions in this regard are still unclear. In this study, P transport in soil columns was investigated by monitoring breakthrough curves and transport model fitting, and the contributions of Fe and total organic carbon (TOC) concentrations, as well as pH to P retention, were determined using multiple linear regression (MLR). The results showed that the rate of P transport in Fe-rich laterite soil was significantly lower (retardation factor R = 458.5) than that in the other soil types (R = 108.4-247.6). Additionally, it was observed that OM formed rate-limited adsorption sites, causing the rapid release of labile P, and owing to P release and readsorption. Even though more significant P releases were observed, chernozem soil had an obvious inhibiting effect on P transport owing to its relatively high Fe content, and the high P-Fe increment (48.9-90.4%) indicated the essential role of Fe minerals in P immobilization. Further, P was readily transported in natural or artificially modified fluvo-aquic soils with high calcium concentrations, and it was also observed that the convection-dispersion equation (CDE) and Thomas models were suitable for describing P retardation and adsorption, respectively. Furthermore, the contribution weights of Fe and TOC concentrations as well as pH to P retardation, based on MLR calculations, were approximately 1.0, -0.3, and -0.2, respectively. Our findings can support the control of eutrophication pollution caused by P leaching.

Chitosan based antibacterial composite materials for leather industry: a review

Abstract

Chitosan is an amorphous translucent substance with a structural unit similar to the polysaccharide structure of the extracellular matrix, It has good antibacterial, biocompatible, and degradable properties. It has important application value in leather, water treatment, medicine, food and other fields, so chitosan and its modified products have received widespread attention. This article reviewed the preparation methods of chitosan-based antibacterial composites in recent years, including chitosan/collagen, chitosan/graphene, chitosan/tannic acid, and chitosan/polyethylene glycol composite materials, elaborates their modification methods and antibacterial mechanism were reviewed in detail, and its applications in the leather industry as antibacterial auxiliaries and water treatment antibacterial adsorption materials were discussed. Finally, the future development and challenges of chitosan-based composite materials in the leather industry were forecasted.

Graphical abstract

Different transport behaviors and mechanisms of perfluorooctanoate (PFOA) and perfluorooctane sulfonate (PFOS) in saturated porous media

Perfluorooctanoate (PFOA) and perfluorooctane sulfonate (PFOS) in soil aroused increasing concern, however there is little information about their transport in porous media, which is urgently needed to better control their environmental risks. In this study, saturated sand columns (considering the coupled effect of solution cation type and pH) and a two-site nonequilibrium transport model (TSM) were used to investigate the transport behaviors and mechanisms of PFOA and PFOS. Breakthrough data and the TSM parameters showed PFOA had higher mobility than PFOS, and divalent cation could inhibit their transport by increasing the nonequilibrium interactions between them and the sand. pH had little influence on PFOA migration when there was only monovalent cation in the solution since PFOA had limited affinity with the sand, however, polyvalent cation could provide additional adsorption sites for it through cation bridging and enhance the effect of pH. Differently, decreasing pH inhibited the transport of PFOS more significantly, and the effect was stronger than that of changing cation type. That proved mechanisms like hydrogen-bonding which were sensitive to solution pH played an important role in PFOS migration. These results provide important scientific basis to the remediation strategy and the migration prediction model development of PFOA and PFOS.

Turning waste into treasure: Reuse of contaminant-laden adsorbents (Cr(vi)-Fe3O4/C) as anodes with high potassium-storage capacity

In this study, we try to find possible solutions to synchronously solving energy and environmental problems. In our design, orange peel is used as a carbon source to synthesize low-cost Fe₃O₄/C composites, which are employed as adsorbents to purify Cr(vi)-contaminated water. After that, these Cr(vi)-laden Fe₃O₄/C composites are used and tested as anodes in potassium-ion batteries. It is found that their K-storage capacity is more than 300 mAh g^-1 at a current density of 0.1 A g^-1, depending on the mass content of Fe₃O₄. The more Fe₃O₄ component in composite, the more adsorbed Cr(vi) species through chemisorption, and the larger K-storage capacity. The good electrical conductivity of cabon-based anodes endows them with superior rate performance. At current densities of 0.1, 0.5, 1 and 2 A g^-1, K-storage capacity amounts to 357.8, 316.3, 276.3 and 236.8 mAh g^-1, respectively. The reuse of contaminant-laden adsorbents as anodes will shed new light on the disposal of exhausted adsorbents after water treatment and development of anode materials for secondary batteries.

Study of the removal of ciprofloxacin by Zn–GO@SA aerogel microspheres

Zn–GO@SA aerogel microspheres were prepared via a simple ionic–gel method, showing excellent adsorption performance toward ciprofloxacin and easy separation from solution.

Recent advances in application of graphitic carbon nitride-based catalysts for degrading organic contaminants in water through advanced oxidation processes beyond photocatalysis: A critical review

Advanced oxidation processes (AOPs) have attracted much interest in the field of water treatment owing to their high removal efficiency for refractory organic contaminants. Graphitic carbon nitride (g-C₃N₄)-based catalysts with high performance and cost effectiveness are promising heterogeneous catalysts for AOPs. Most research on g-C₃N₄-based catalysts focuses on photocatalytic oxidation, but increasingly researchers are paying attention to the application of g-C₃N₄-based catalysts in other AOPs beyond photocatalysis. This review aims to concisely highlight recent state-of-the-art progress of g-C₃N₄-based catalysts in AOPs beyond photocatalysis. Emphasis is made on the application of g-C₃N₄-based catalysts in three classical AOPs including Fenton-based processes, catalytic ozonation and persulfates activation. The catalytic performance and involved mechanism of g-C₃N₄-based catalysts in these AOPs are discussed in detail. Meanwhile, the effect of water chemistry including pH, water temperature, natural organic matter, inorganic anions and dissolved oxygen on the catalytic performance of g-C₃N₄-based catalysts are summarized. Moreover, the reusability, stability and toxicity of g-C₃N₄-based catalysts in water treatment are also mentioned. Lastly, perspectives on the major challenges and opportunities of g-C₃N₄-based catalysts in these AOPs are proposed for better developments in the future research.

Developments in the Application of Nanomaterials for Water Treatment and Their Impact on the Environment

Nanotechnology is an uppermost priority area of research in several nations presently because of its enormous capability and financial impact. One of the most promising environmental utilizations of nanotechnology has been in water treatment and remediation where various nanomaterials can purify water by means of several mechanisms inclusive of the adsorption of dyes, heavy metals, and other pollutants, inactivation and removal of pathogens, and conversion of harmful materials into less harmful compounds. To achieve this, nanomaterials have been generated in several shapes, integrated to form different composites and functionalized with active components. Additionally, the nanomaterials have been added to membranes that can assist to improve the water treatment efficiency. In this paper, we have discussed the advantages of nanomaterials in applications such as adsorbents (removal of dyes, heavy metals, pharmaceuticals, and organic contaminants from water), membrane materials, catalytic utilization, and microbial decontamination. We discuss the different carbon-based nanomaterials (carbon nanotubes, graphene, graphene oxide, fullerenes, etc.), and metal and metal-oxide based nanomaterials (zinc-oxide, titanium dioxide, nano zerovalent iron, etc.) for the water treatment application. It can be noted that the nanomaterials have the ability for improving the environmental remediation system. The examination of different studies confirmed that out of the various nanomaterials, graphene and its derivatives (e.g., reduced graphene oxide, graphene oxide, graphene-based metals, and graphene-based metal oxides) with huge surface area and increased purity, outstanding environmental compatibility and selectivity, display high absorption capability as they trap electrons, avoiding their recombination. Additionally, we discussed the negative impacts of nanomaterials such as membrane damage and cell damage to the living beings in the aqueous environment. Acknowledgment of the possible benefits and inadvertent hazards of nanomaterials to the environment is important for pursuing their future advancement.

Removal of microplastics via drinking water treatment: Current knowledge and future directions

The occurrence of microplastics in drinking water systems has increasingly become a major environmental challenge. Although the potential impacts of microplastics in drinking water on humans are not yet fully understood, microplastics attract the public health concern when they are consumed by humans through drinking water systems. Current drinking water treatment plants constitute an obstacle to the entry of microplastics from raw water into daily drinking water. Therefore, understanding the behaviors of drinking water treatment process and the fates of microplastics in drinking water treatment plants are very important. We systematically reviewed the available knowledge on the global existence of microplastics in raw water, treated water and tap water in this paper. This will offer a new perspective for the threat of microplastics in drinking water to human health and help to formulate effective strategies for microplastic monitoring. The existing knowledge of microplastic removal by different treatment processes was also thoroughly discussed. Additionally, the potential challenges of microplastic removal from treatment processes and remediation strategies of microplastics in drinking water were also put forward. The relationship between the properties and behavior of microplastics during different treatment processes is suggested to explore in the future.

Comparative studies on the adsorption of metal ions from aqueous solutions using various functionalized graphene oxide sheets as supported adsorbents

Graphene oxide (GO) was chemically modified by bis(2-pyridylmethyl)amino groups (BPED) through a multistep procedure. For comparison, and to justify the grafting of BPED groups onto the GO sheets, the GO-based material obtained after each step was used as a solid phase adsorbent for removing Cu(II), Ni(II) and Co(II) metal ions from aqueous solutions. The influence of metal ion concentrations, pH, contact time and temperature on their adsorption onto the GO-based adsorbents was investigated and the GO-EDA-CAC-BPED adsorbent showed the highest ability to adsorb Cu(II), Ni(II) and Co(II) with a concentration of 250 mg.L^-1 at pH = 7. Additionally, it was demonstrated that the equilibrium adsorption capacities of these metal ions followed the order of Cu(II)>Ni(II)>Co(II) whatever the GO-based adsorbent. Moreover, to examine the underlying mechanism of the adsorption process, pseudo-first order, pseudo-second order, Elovich or Roginsky-Zeldovich and intraparticle diffusion models were fitted to experimental kinetic data. It was shown that the pseudo-second-order model was the most appropriate one to describe the adsorption of heavy metal ions by the GO-based materials. Finally, it was demonstrated that their desorption/regeneration capacities were higher than 10 cycles, opening the path to the removal of metal ions from wastewater solutions.

Influence of multi-walled carbon nanotubes on the microbial biomass, enzyme activity, and bacterial community structure in 2,4-dichlorophenol-contaminated sediment

The rise in manufacture and use of carbon nanotubes has aroused the concern about their potential risks associated with coexisting pollutants in the aquatic environment. 2,4-dichlorophenol (2,4-DCP), with a high toxicity to many aquatic organisms, is a widespread pollutant resulting from the extensive use of pesticides and preservatives. In this article, the adsorption of 2,4-DCP by riverine sediment and the responses of sediment microbial community to 2,4-DCP were studied in the presence of multi-walled carbon nanotubes (MWCNTs). Adding MWCNTs significantly increased the adsorption amount of sediment for 2,4-DCP from 0.541 to 1.44 mg/g as the MWCNT concentration increased from 0 to 15 mg/g. The responses of sediment microbial community were determined after one-month exposure to MWCNTs at different concentrations (0.05, 0.5, 5, and 50 mg/g). The microbial biomass carbon in the sediment contaminated with 2,4-DCP increased in the presence of 5 mg/g of MWCNTs (from 0.06 to 0.11 mg/g), but not significantly changed at other MWCNT concentrations. For the sediments contaminated with 2,4-DCP, the presence of MWCNTs made no difference to urease activity, while the dehydrogenase activity slightly increased with the addition of 5 mg/g of MWCNTs and decreased in the presence of 50 mg/g of MWCNTs. The changes of sediment bacterial communities were further determined by 16S rRNA gene sequencing. Based on the weighted UniFrac distance between communities, the clustering analysis suggested that the contamination of 2,4-DCP affected the bacterial community structure in a greater degree than that caused by MWCNTs at relatively low concentrations (≤5 mg/g). Bacteroidetes, Planctomycetes, and Nitrospirae were feature bacterial phyla to reflect the effects of MWCNTs and 2,4-DCP on sediment bacterial community. These results may contribute to the understanding of microbial community response to co-exposure of MWCNTs and 2,4-DCP and the assessment of associated ecological risks.

Snow pollution by nitrogen-containing substances as a consequence of rocket launches from the Baikonur Cosmodrome

In this paper, we assessed snow pollution by nitrogen-containing substances including rocket propellants - UDMH (unsymmetrical dimethylhydrazine, (СН₃)₂NNH₂) and NT (nitrogen tetroxide, N₂O₄) - and their transformation products (NDMA (nitrosodimethylamine, (CH₃)₂NNO), NO₃^-, NO₂^- and NH₄⁺) within the falling regions (FRs) of the first and second stages of Proton-M rockets launched from the Baikonur Cosmodrome. At the first stage FR in Central Kazakhstan, snow with a pH range from 1.7 to 9.0 was contaminated by N-containing substances (maximal value in g/L): UDMH - 0.27, NDMA - 0.04, NO₃^- - 19, NH₄⁺ - 0.04 and NO₂^- - 0.13. The first stage landing resulted in snow contamination by soil dust particles and N-containing substances at a rate of 13 g/m² and 82 mg/m²/day, respectively. The maximal permissible addition (MPA) for UDMH, NDMA and NO₃^- to the 0-5 cm layer of soil was estimated at 0.06, 0.006 and 70.2 mg/m², respectively. At the second stage FR in the NE Altai, substances released by space transportation were absent and the concentration of NO₃^- and NH₄⁺ corresponded to the natural background level. The index of contamination (IC) was used for characterizing the degree of snow contamination by N-containing substances. A simulation model was developed for analysing the dependence of snow contamination by rocket propellant components on the weather parameters.

Bioremediation of water containing pesticides by microalgae: Mechanisms, methods, and prospects for future research

The application of pesticides reduces the loss of crops while simultaneously increasing crop productivity. However, the frequent use of pesticides can cause serious environmental problems due to their high accumulative and persistent nature. Recently, microalgae technology has received considerable success in the efficient treatment of pesticides pollution. In this review, the metabolic mechanisms responsible for the removal of pesticides are summarized based on previous studies. Different methods used to enhance the ability of microalgae to remove pesticides are critically evaluated. The recycling of microalgae biomass after wastewater treatment for biochar preparation and biodiesel production using the biorefinery approach is also introduced. Furthermore, we present potential future research directions to highlight the prospects of microalgae research in the removal of pesticides along with the production of value-added products.

An Ion-Crosslinked Supramolecular Hydrogel for Ultrahigh and Fast Uranium Recovery from Seawater

Large-scale uranium extraction from seawater is a crucial but challenging part of nuclear power generation. In this study, a new ion-crosslinked supramolecular Zn²⁺ -poly(amidoxime) (PAO) hydrogel that can super-efficiently adsorb uranium from seawater is explored. By simply mixing two solutions of zinc chloride and PAO, a supramolecular Zn²⁺ -PAO hydrogel is achieved via the interaction between zinc cations and amidoxime anions. In contrast with existing amidoxime-functionalized hydrogel-based adsorbents having low PAO contents and fiber-based adsorbents with weak hydrophilicity, the PAOs can be directly crosslinked using a small quantity of superhydrophilic zinc ion. Thus, a supramolecular hydrogel is formed, having both a high content of well-dispersed PAOs and good hydrophilicity. Relative to reported adsorbents, this low-cost hydrogel membrane exhibits outstanding uranium adsorption performance, reaching 1188 mg g^-1 of M_U /M_{dry gel} in 32 ppm uranium-spiked water. More importantly, after immersion in natural seawater for only 4 weeks, the uranium extraction capacity of the Zn²⁺ -PAO hydrogel membrane reaches 9.23 mg g^-1 of M_U /M_{dry gel} . This work can provide a general strategy for designing a new type of supramolecular hydrogel, crosslinked by various bivalent/multivalent cation-crosslinkers and even many other superhydrophilic supramolecular crosslinkers, for the high-efficient and massive extraction of uranium from seawater.

New guidelines for testing "Deep eutectic solvents" toxicity and their effects on the environment and living beings

Deep eutectic solvents (DESs) were described at the beginning of this century as an alternative to ionic liquids (ILs) in green chemistry. Despite their obvious sustainable advantages as reaction media, there is still controversy about their potential toxicity. Most of the ecotoxicity assays done up to now involving DESs are based on antibiograms. This is not a good approach due to the high density and viscosity of most DESs already described. Additionally, antibiograms do not allow continuous monitoring of neither cellular growth nor changes on physicochemical parameters like culture acidification due to cellular growth or DESs metabolization. This work starts by displaying advantages and disadvantages of the DESs toxicity assays already reported. Then, using a new DES recently described and Escherichia coli as a model microorganism, liquid cultures with continuous monitoring of pH, temperature, shaking and optical density have been used, for the first time, to quantify potential toxicity of the DES as well as the degree of the cellular tolerance (in preadapted and non-preadapted cells). The results obtained show that this new DES is not toxic for E. coli at concentrations up to 300 mM and cellular preadaptation was crucial for the cells to grow. At concentrations between 300 mM and 450 mM, cells can tolerate this DES. Above 600 mM, the DES is toxic causing complete inhibition of growth. This toxicity is not only due to the chemical composition of the DES, but also due to the high acidification of the media caused by the DES hydrolysis during cellular growth. The consequences of sterilization procedures on the DES stability are also analysed into detail, finding that sterilization by autoclave promotes DES hydrolysis. From these results, new guidelines are proposed for furthers studies aiming to characterize and quantify DESs toxicity.

Adsorption of Ba2+ and Sr2+ on Ti3C2Tx MXene in model fracking wastewater

Wastewater from hydraulic fracking contains both organic and inorganic pollutants; the latter include radioactive nuclides such as Ba²⁺ and Sr²⁺. We explored whether MXene (Ti₃C₂T_x), a novel adsorbent, could remove Ba²⁺ and Sr²⁺ from model wastewater. Zeta potential analysis showed that MXene had a high negative surface charge. MXene adsorbed Ba²⁺ and Sr²⁺ via electrostatic attraction, as confirmed by the adsorption at different solution pH values and in the presence of various concentrations of other ions (NaCl and CaCl₂). MXene exhibited outstanding adsorption of Ba²⁺ and Sr²⁺, to approximately 180 and 225 mg g^-1, respectively, when 1 g L^-1 MXene was admixed with adsorbates at 2 g L^-1. MXene exhibited very rapid adsorption kinetics, attaining equilibrium within 1 h. X-ray photoelectron spectroscopy and Fourier-transform infrared spectroscopy revealed that MXene adsorbed Ba²⁺ and Sr²⁺, respectively, via ion exchange and inner-sphere complex formation. Finally, we performed MXene reusability tests; reusability was excellent over at least four cycles. Thus, MXene removed Ba²⁺ and Sr²⁺ from model fracking wastewater.

The mechanism for adsorption of Cr(VI) ions by PE microplastics in ternary system of natural water environment

More attention was paid to the attachment between microplastics and environmental pollutants. The adsorption performance of Polyethylene (PE) beads (a typical type of microplastics) and Cr(VI) ions with the existence of sodium dodecyl benzene sulfonate (SDBS) was investigated in this paper. The adsorption experiments of Cr(VI) ions by PE microplastics were conducted at different conditions, i.e. PE doses, pH and SDBS concentrations, respectively. The adsorption capability of Cr(VI) ions was increased from 0.39 to 1.36 mg⋅g^-1 when the dosage of PE microplastics was increased from 2 to 14 g ⋅L^-1 at pH of 5 with addition of SDBS, compared with increasing adsorption capability from 0.03 to 0.32 mg⋅g^-1 without addition of SDBS. The pH would influence the adsorption capability with and without the addition of SDBS. When the pH was less than 6, the adsorption capability of Cr(VI) would be promoted by the addition of SDBS; however, there was a contrast tendency when the pH was more than 6, which was attributed to that SDBS would compete with CrO₄^2- for occupying the adsorption sites of PE microplastic. The SDBS concentration would affect the adsorption performance of Cr(VI) ions onto PE microplastics. The peak of the adsorption capacity was at SDBS concentration between 1 and 1.5 mM. This research would provide a basis for investigating the influence of SDBS on adsorption performance of heavy metal by PE microplastics to simulate the surface attachment model of those three kinds of pollutants.

Control schemes for a complex biorefinery plant for bioenergy and biobased products

This work proposes innovative feedback control schemes for a complex biorefinery plant which contains two continuous bioreactors: an anaerobic digester and a photobioreactor. The anaerobic digester is used to decompose organic matter inside a wastewater treatment process, the most useful final product being biogas/methane. The photobioreactor is used for a microalgae photosynthetic growth process where some components with added value are produced, and bio-mitigation of the carbon dioxide emissions is achieved. By using realistic models of the anaerobic digester and of the photobioreactor, novel adaptive and robust control schemes are designed. These proposed structures contain linearizing controllers, state observers and parameter estimators for the bioprocess unknown kinetics. The control designs are validated via numerical simulations that consider several realistic restrictions and disturbances which act on the process: unavailability of some biological variables, unknown and time-varying reaction kinetics, uncertain and time-varying influent flow rates, noisy measurements.

Advances in the application, toxicity and degradation of carbon nanomaterials in environment: A review

Carbon nanomaterials (CNMs) are novel nanomaterials with excellent physicochemical properties, which are widely used in biomedicine, energy and sensing. Besides, CNMs also play an important role in environmental pollution control, which can absorb heavy metals, antibiotics and harmful gases. However, CNMs are inevitably entering the environment while they are rapidly developing. They are harmful to living organisms in the environment and are difficult to degrade under natural conditions. Here, we systematically describe the toxicity of carbon nanotubes (CNTs), graphene (GRA) and C₆₀ to cells, animals, humans, and microorganisms. According to the current research results, the toxicity mechanism is summarized, including oxidative stress response, mechanical damage and effects on biological enzymes. In addition, according to the latest research progress, we focus on the two major degradation methods of chemical degradation and biodegradation of CNTs, GRA and C₆₀. Meanwhile, the reaction conditions and degradation mechanisms of degradation are respectively stated. Moreover, we have prospects for the limitations of CNM degradation under non-experimental conditions and their potential application.

Sorption and transport of trenbolone and altrenogest photoproducts in soil-water systems

This study evaluated the sorption and transport potential of seven phototransformation products of 17α-trenbolone, 17β-trenbolone, trendione, and altrenogest, along with the parent trienone steroids in batch and column soil-water systems. In batch systems, the target solutes exhibited linear isotherms, with values for sorption coefficients (log Koc) of parent steroids (2.46-2.76) higher than those for photoproducts (1.92-2.57). In column systems, the estimated retardation factors (Rsol) for parents (2.7-5.1) were ∼2-5 times higher than those for photoproducts (0.84-1.7). The log Koc (R2 = 0.75) and Rsol (R2 = 0.89-0.98) were well correlated with measured log Kow values, indicating that hydrophobic partitioning governed the soil-solute interaction of these biologically potent compounds in soil-water systems. These data indicated that photoproducts exhibited reduced sorption affinity and increased transport potential relative to more hydrophobic parent structures. In agroecosystems, traditional runoff management practices would be expected to exhibit reduced treatment effectiveness for photoproducts relative to the parent compounds of commonly used trienone steroids.

Effects of multi-walled carbon nanotubes on metal transformation and natural organic matters in riverine sediment

In this study, pragmatic prospection of multi-walled carbon nanotubes (MWCNTs) is conducted considering their impacts on Cd transformation, microbial activity and natural organic matter (NOM) in sediments. Indeed, dose-dependent of MWCNTs acceleration in Cd sedimentation and immobilization in water-sediment interface has been found. Unexpectedly, even with the reduced Cd bioavailability, high ratios of MWCNTs incorporation led to exacerbated microbial inactivation. Besides, we noted that MWCNTs significantly lowered NOM contents in sediments. Chemical characterization results also demonstrated that high ratios of MWCNTs incorporation reduced the aromaticity, hydrophobicity and humification of fulvic acid (FA) and humic acid (HA) in sediments. The Cd binding results confirmed that quantity and chemical variation of NOM affected their central ability to Cd binding, referring to significant decrease in combined Cd contents. The findings indicated that reduction in humic substances and chemical structure variation might be the important reason attributed to the MWCNTs toxicity. This study provides novel mechanisms understanding the fate of carbon nanotubes considering the balance in environmental benefit and potential risks.

Enhanced adsorption of arsenate and antimonate by calcined Mg/Al layered double hydroxide: Investigation of comparative adsorption mechanism by surface characterization

This study aims to investigate adsorption mechanisms of As(V) and Sb(V) on calcined Mg/Al layered double hydroxide (LDH). The calcination process of Mg/Al LDH (CLDH) considerably enhanced the adsorption capacity of As(V) and Sb(V) via reconstruction and new formation of brandholzite-like compound, respectively. The maximum adsorption capacity for As(V) and Sb(V) by CLDH was 102.9 mg/g and 303.3 mg/g, respectively. The regeneration efficiency of As(V) by 0.5 M NaOH with 5 M NaCl mixed solution reached 72.3% during five regeneration cycles, while Sb(V) regeneration gradually decreased to 32.0% at the fifth regeneration cycles due to the irreversible surface complexation mechanism. Extended X-ray absorption fine structure (EXAFS) data displayed that Al plays a dominant role in the adsorption of As(V) on CLDH through bidentate-binuclear inner-sphere complex. On the other hand, XRD and EXAFS data revealed that Sb(V) formed a brandholzite-like structure Mg[Sb(OH)₆]₂·6H₂O which forms outer-sphere complex by the hydrogen bonding between hexagonal plates of magnesium and antimony hydroxide. Although the formation of brandholzite-like structure causes the partial transformation of original structure of Mg/Al LDH during reconstruction process with decreasing regeneration efficiency, it could be attributed to high binding affinity between Sb(V) and Mg/Al LDH.

Sorption and desorption characteristics of anionic surfactants to soil sediments

Surfactants are important environmental chemicals due to their extensive domestic and industrial applications, such as subsurface organic pollution remediation and enhanced oil recovery. However, the interaction of surfactants with subsurface material particularly the desorption behavior of surfactants is less understood. Surfactant desorption is essential to control the fate and transport of surfactants as well as organic pollutants. In this study, the sorption and desorption of linear sodium dodecylbenzene sulfonate (SDBS) and sodium hexadecyl diphenyl oxide disulfonate (DPDS) with two types of soil sediment samples are compared. Sorption of surfactants can be modeled by hydrophobic sorption. Less DPDS sorption is observed at a higher aqueous concentration, which is attributed to the competition between surfactant micelles and sediment organic matter for DPDS sorption. A significant fraction of the sorbed surfactants resists desorption, and this is not a result of surfactant precipitation or desorption kinetics. Surfactant desorption behavior is similar to the irreversible desorption of hydrocarbons from soil with only half of the resistant phase surfactant being readily extracted by heated solvent extraction. The sorption/desorption data are interpreted with a molecular topology and irreversible sorption model. The knowledge of this study can be useful in understanding the environmental fate and transport of these common anionic surfactants. The methodology developed in this study can be expanded to study the sorptive nature of a wider range of surfactants in the environment.