Ion exchange removal of Cu(II), Fe(II), Pb(II) and Zn(II) from acid extracted sewage sludge - Resin screening in weak acid media

Understanding competitive Cu2+ and Zn2+ adsorption onto functionalized cellulose fiber via experimental and theoretical approach

Amidoxime groups were successfully introduced to develop a novel amidoxime-functionalized cellulose fiber (AO-Cell) for absorptive removal of heavy metal ions in wastewater. The chemical structure, and the competitive adsorption of Cu2+ and Zn2+ by AO-Cell were investigated by experiments study, Density functional theory (DFT) and molecular dynamic (MD) simulation. The results showed the N and O atoms in the amidoxime group can spontaneously interact with Cu2+ and Zn2+ through sharing long pair electrons to generate stable coordination structure, which was the dominant adsorption mechanism. Besides, the enlarged surface area, improved hydrophilicity and dispersion offered by AO-Cell facilitate the adsorption process by increasing the accessibility of absorption sites. As results of these synergetic modification, AO-Cell can remain effective in a wide pH range (1-6) and reach adsorption equilibrium within 60 min. At optimal conditions, the achieved theoretical adsorption capacity is as high as 84.81 mg/g for Cu2+ and 61.46 mg/g for Zn2+ in the solution with multiple ions. The competition between Cu2+ and Zn2+ in occupying the absorption sites arises from the difference in the metallic ion affinity and covalent index with the adsorbent as demonstrated by the MD analysis. Importantly, AO-Cell demonstrated favorable recyclability after up to 10 adsorption-desorption cycles.

Insight into Cu (II) adsorption on pyrochar and hydrochar resultant from Acacia Senegal waste for wastewater decontamination

Acacia Senegal waste (ASW) is remaining biomass following gum Arabic harvesting and has no use mentioned in the literature as of yet. This study aims to convert ASW into valuable biochar via two comparative thermal and hydrothermal techniques, which include pyrochar ASW at 300 °C (PC ASW300) and hydrochar ASW at 180 °C (HC ASW180), respectively, for Cu (II) adsorption from aqueous solutions. SEM-EDS, FTIR, XRD, and XPS were used to characterize the biochar. Adsorption performance was studied as a function of pH, contact time, and adsorbent concentration. Adsorption kinetics were best fit for a pseudo-second-order model. And thermodynamics studies revealed that Cu (II) on biochar was endothermic, spontaneous, and best fitted to the Langmuir isotherm model. Pyrochar adsorption capacity (31.93 mg g-1) was seven times that of hydrochar (5.45 mg g-1). ASW treated with phosphorus (PC H3PO4 and HC H3PO4) prior to the carbonization altered the pore structure and surface functional groups as well (O-P-O, P-CH3, and P-OH) of biochar. It was found that treating with phosphorous acid increased adsorption capacity to 141.7 mg g-1 and 22.24 mg g-1 for PC H3PO4 and HC H3PO4, respectively. The surface functional groups of biochar resulted from lignin, alkaloids, and polysaccharides combined with Cu (II) during the adsorption process via surface complexation accompanied by π-electron interaction and Cu (II) reduction. These findings shed light on the ASW biochar potential as a new green cost-effective adsorbent and drew an insightful understanding of Cu (II) adsorption performance and mechanism. It is concluded that ASW-derived biochar is highly effective and a promising alternative for Cu (II) decontamination from wastewater.

Preparation of magnetic DTPA-modified chitosan composite microspheres for enhanced adsorption of Pb(II) from aqueous solution

In this study, magnetic DTPA-modified chitosan composite microspheres (MDCM) were prepared by reverse emulsion-double crosslinking method (carbodiimide followed by glutaraldehyde) for removal of Pb(II) from aqueous solution. The obtained magnetic adsorbents were characterized by FTIR, SEM, XRD, VSM, BET, and 13C NMR. The effects of the pH, contact time, initial concentration, and competitive metal cations (Na(I), Ca(II), or Mg(II)) on Pb(II) adsorption were investigated. The results revealed that MDCM exhibited high removal performance over a wide pH range and in the presence of competitive metal cations. The maximum adsorption capacity of MDCM for Pb(II) is 214.63 mg g-1 at pH 3, which is higher than most recently reported magnetic adsorbents. Adsorption kinetics and isotherms can be described by the pseudo-second-order model and Langmuir model, respectively. In addition, MDCM is easy to regenerate and can be reused five cycles with high adsorption capacity. Finally, the adsorption mechanism was further revealed by FTIR and XPS analysis. Overall, MDCM has practical application potential in removing Pb(II) from contaminated wastewater due to its high adsorption efficiency, good reusability, and convenient magnetic separation.

Efficient heavy metal ion removal by fluorographene nanochannel templated molecular sieve: a molecular dynamics simulation study

Environmental water contamination, particularly by heavy metal ions, has emerged as a worldwide concern due to their non-biodegradable nature and propensity to accumulate in soil and living organisms, posing a significant risk to human health. Therefore, the effective removal of heavy metal ions from wastewater is of utmost importance for both public health and environmental sustainability. In this study, we propose and design a membrane consisting of fluorographene (F-GRA) nanochannels to investigate its heavy metal ion removal capacity through molecular dynamics simulation. Although many previous studies have revealed the good performance of lamellar graphene membranes for desalination, how the zero-charged graphene functionalized by fluorine atoms (fully covered by negative charges) affects the heavy metal ion removal capacity is still unknown. Our F-GRA membrane exhibits an exceptional water permeability accompanied by an ideal heavy metal ion rejection rate. The superior performance of F-GRA membrane in removing heavy metal ions can be attributed to the negative charge of the F-GRA surface, which results in electrostatic attraction to positively charged ions that facilitates the optimal ion capture. Our analysis of the potential of mean force further reveals that water molecule exhibits the lowest free energy barrier relative to ions when passing through the F-GRA channel, indicating that water transport is energetically more favorable than ion. Additional simulations of lamellar graphene membranes show that graphene membranes have higher water permeabilities compared with F-GRA membranes, while robustly compromising the heavy meal ion rejection rates, and thus F-GRA membranes show better performances. Overall, our theoretical research offers a potential design approach of F-GRA membrane for heavy metal ions removal in future industrial wastewater treatment.

Efficient multi-ion adsorption using chitosan-malonic acid film: Enhancement using response surface methodology

The objective of this research is to conduct a comprehensive characterization of chitosan while also improving its attributes by crosslinking with malonic acid, with a focus on its efficacy in removing hexavalent chromium, arsenite and fluoride ions. Crosslinking chitosan in 1:0.5 mass ratio forming a film led to substantial enhancement in confiscation of these target pollutants. The characterization of the adsorbent involved several techniques, including FT-IR, TGA-DSC, SEM-EDX, XRD, and BET surface area analysis. In batch adsorption experiments, Chitosan-malonic acid (CMA) was employed to remove CrVI, AsIII and F- from aqueous solutions. These experiments were conducted while varying conditions such as pH, dosage, concentration, temperature, and time. Through the implementation of response surface methodology (RSM), parameters were optimized, resulting in over 95% removal of CrVI, AsIII and F- ions. The isotherm and kinetics data demonstrated a good fit with the Langmuir isotherm model and pseudo second-order kinetics, respectively. According to the Langmuir isotherm, the maximum adsorption capacities on CMA for CrVI, AsIII and F- were determined to be 687.05 mg g-1, 26.72 mg g-1 and 51.38 mg g-1 respectively under optimum pH of 4.0, 7.0 and 5.0 respectively under ambient temperature of 303 K. Thermodynamic analysis indicated that the adsorption process was spontaneous and driven by enthalpy. The regenerability of the adsorbent was validated through five adsorption-desorption cycles, signifying its reusability. An assessment of the adsorbent's sustainability indicated an eco-friendly synthesis, as reflected by the low E-factor value of 0.0028.

Synthesis of Plant-Mediated Iron Oxide Nanoparticles and Optimization of Chemically Modified Activated Carbon Adsorbents for Removal of As, Pb, and Cd Ions from Wastewater

This research study was designed with the aim to prepare plant extract-mediated iron oxide nanoparticles (IONPs) and different chemically modified carbon adsorbents from the Parthenium hysterophorus plant and then optimize the carbon adsorbents by evaluating their adsorption applications in wastewater for the selected metal ions like arsenic (As3+), lead (Pb2+), and cadmium (Cd2+). The Fourier transform infrared spectroscopy (FTIR) technique was used to highlight functional groups in plant-mediated IONPs and chemically modified carbon adsorbents. A scanning electron microscopy study was conducted to explain the surface morphology of the adsorbents. Energy-dispersive X-rays was used for elemental analysis and X-ray diffraction for particle size and crystallinity of the adsorbents. From the study, it was found that the best optimum conditions were pH = 5-6, initial concentration of adsorbate of 10 mg/L, dose of adsorbent of 0.01 g, contact time of 90-120 min of adsorbent and adsorbate, and temperature of 25 °C. At optimum conditions, the adsorption capacities of IONPs for arsenic (As) 144.7 mg/g, lead (Pb) 128.01 mg/g, and cadmium (Cd) ions 122.1 mg/g were recorded. The activated carbon at optimum conditions showed adsorption capacities of 46.35 mg/g for As, 121.95 mg/g for Pb, and 113.25 mg/g for Cd ion. At equilibrium, Langmuir, Freundlich Temkin, and Dubinin-Radushkevich isotherms were applied on the experimental adsorption data having the best R2 values (0.973-0.999) by the Langmuir isotherm. High-correlation coefficient R2 values (0.996-0.999) were obtained from the pseudo-second-order for all cases, showing that the adsorption process proceeds through pseudo second-order kinetics. The apparent adsorption energy E value was in the range of 0.24-2.36 kJ/mol. The adsorption capacity of regenerated IONPs for As gradually decreased from 144.8 to 45.67 mg/g, for lead 128.15 to 41.65 mg/g, and cadmium from 122.10 to 31.20 mg/g in 5 consecutive cycles. The study showed that the synthesized IONPs and acid-activated carbon adsorbent were successfully used to remove selected metal ions from wastewater.

Reparation of nano-FeS by ultrasonic precipitation for treatment of acidic chromium-containing wastewater

Nano-FeS is prone to agglomeration in the treatment of chromium-containing wastewater, and ultrasonic precipitation was used to synthesize nano-FeS to increase its dispersion. The optimization of the preparation method was carried out by single factor method (reaction temperature, Fe/S molar ratio and FeSO4 dropping flow rate) and response surface methodology. Dynamic experiments were constructed to investigate the long-term remediation effect and water column changes of nano-FeS and its solid particles. The changes of the remediation materials before and after the reaction were observed by SEM, and the mechanism of the remediation of chromium-containing wastewater by nano-FeS prepared by ultrasonication was revealed by XRD. The results showed that the reaction temperature of 12 °C, Fe/S molar ratio of 3.5 and FeSO4 dropping flow rate of 0.5 mL/s were the best parameters for the preparation of nano-FeS. The nano-FeS has efficient dispersion and well-defined mesoporous structure in the form of needles and whiskers of 40-80 nm. The dynamic experiments showed that the average removal of Cr(VI) and total chromium by nano-FeS and its immobilized particles were 94.97% and 63.51%, 94.93% and 45.76%, respectively. Fe2+ and S2- ionized by the FeS nanoparticles rapidly reduced Cr(VI) to Cr(III). Part of S2- may reduce Fe3+ to Fe2+, forming a small iron cycle that gradually decreases with the ion concentration. Cr(III) and Fe2+ form Cr(OH)3 and FeOOH, respectively, with the change of aqueous environment. Another part of S2- reacts with Cr(III) to form Cr2S3 precipitate or is oxidized to singlet sulfur. The FeS nanoparticles change from short rod-shaped to spherical shape. Compared with the conventional chemical precipitation method, the method used in this study is simple, low cost, small particle size and high removal rate per unit.

Starch modified NiFe layered double hydroxide composites for better adsorption and photocatalytic removal of reactive dye and piroxicam-20 drug

One of the most omnipresent problems to the environment is the efficient removal of textile dyes and non-steroidal drugs from wastewater. For this purpose, renewable, sustainable, and biodegradable biopolymers are used. In this study, starch (S) modified NiFe-layered double hydroxide (LDH) composites were successfully synthesized by the co-precipitation method and have been examined as a catalyst for the effective adsorption of reactive blue 19 dye, reactive orange 16 dye, and piroxicam-20 NSAID from wastewater and photocatalytic degradation of reactive red 120 dye. The physicochemical properties of the prepared catalyst were assessed by XRD, FTIR, HRTEM, FE-SEM, DLS, ZETA, and BET. The coarser and more porous micrographs are shown in FESEM, indicating the homogeneous dispersion of layered double hydroxide on starch polymer chains. The S/NiFe-LDH composites have a slightly greater S_BET (6.736 m²/g) than NiFe LDH (4.78 m²/g). The S/NiFe-LDH composite shows remarkable ability in the removal of reactive dyes. The band gap value of NiFe LDH, S/NiFe LDH (0.5:1), and S/NiFe LDH (1:1) composites was calculated as 2.28 eV, 1.80 eV, and 1.74 eV, respectively. The q_max assessed from Langmuir isotherm for removal of piroxicam-20 drug, reactive blue 19 dye, and reactive orange 16 was 2840 mg/g, 149.47 mg/g, and 182.4 mg/g, respectively. The activated chemical adsorption without product desorption is predicted by the Elovich kinetic model. With reactive red 120 dye, S/NiFe-LDH shows photocatalytic degradation within 3 h of irradiation of visible light with 90% removal efficiency and follows a pseudo-first-order kinetic model. The scavenging experiment confirms the involvement of electrons and holes in photocatalytic degradation. With a little decline in adsorption capacity up to five cycles, starch/NiFe LDH was easily regenerated. So, the suitable adsorbent required for wastewater treatment is nanocomposites of LDHs and starch as they enhance the chemical and physical attributes of the composite structure with greater absorption capabilities.

Enhanced selective copper precipitation by mechanochemically activated benzene tricarboxylic acid

Toward the treatment of waste solution containing heavy metals, direct precipitation of the metal ions from an acidic solution without alkaline neutralisation is still the greatest challenge. Based on the ligand properties of benzene tricarboxylic acid (BTC) to copper ions, a simple ball milling with 90 min at 400 rpm was used to activate BTC to enhance its capacity for copper removal from the pH of the original solution around 3-4. A set of analytical methods were used to characterise the activated BTC sample and BTC-Cu precipitate before and after copper precipitation. Compared with the raw BTC, the activated BTC could efficiently remove copper ions over 90% from an initial copper concentration of 100 mg/L in a shorter time from an acidic media with lower pH of around 2.60 and the maximum adsorption capacity can be stable at about 111.70 mg/g, resulting from probably the enhanced deprotonation effect for copper incorporation. Furthermore, at controlled dosage, the activated BTC demonstrated much high selectivity on precipitating copper ions from other heavy metals of Ni, Mn, Zn and Cd and provided a new approach for easy copper recycling from waste solution as secondary sources. This process may serve the purpose of recycling both metal and acidic solutions after the purification.

Life Cycle Assessment as Support Tool for Development of Novel Polyelectrolyte Materials Used for Wastewater Treatment

This life cycle assessment (LCA) study focused on comparing the environmental performances of two types of synthesis strategies for polyethyleneimine (PEI) coated silica particles (organic/inorganic composites). The classic layer-by-layer and the new approach (one-pot coacervate deposition) were the two synthesis routes that were tested for cadmium ions removal from aqueous solutions by adsorption in equilibrium conditions. Data from the laboratory scale experiments for materials synthesis, testing, and regeneration, were then fed into a life cycle assessment study so that the types and values of environmental impacts associated with these processes could be calculated. Additionally, three eco-design strategies based on material substitution were investigated. The results point out that the one-pot coacervate synthesis route has considerably lower environmental impacts than the layer-by-layer technique. From an LCA methodology point of view, it is important to consider material technical performances when defining the functional unit. From a wider perspective, this research is important as it demonstrates the usefulness of LCA and scenario analysis as environmental support tools for material developers because they highlight environmental hotspots and point out the environmental improvement possibilities from the very early stages of material development.

Removal of heavy metals from aqueous solutions by high performance capacitive deionization process using biochar derived from Sargassum hemiphyllum

Capacitive deionization (CDI) has been considered as an efficient, energy-saving and environmental friendly technology for water treatment. For the practical application of CDI, high-performance electrode materials beyond standard activated carbon should be developed. In this study, biochar derived from brown algae Sargassum hemiphyllum prepared by pyrolysis at 300-700 °C and then used as the CDI electrode to remove Cu(II) from aqueous solutions. According to the findings, the optimal pyrolysis temperature was 700 °C, and the electrosorption capacity of BAB700 was 75-120 mg·g-1 at an applied voltage of 1.2 V across wide range of initial pH, temperatures and ion types. Moreover, BAB700 also exhibited outstanding ability to electrosorb other heavy metals (Zn(II), Ni(II), and Cd(II)). In addition, the BAB700 retained the Cu(II) removal efficiency of 70 % in 10 cycles. Cu(II) in actual water is completely eliminated with great reproducibility, resulting in a high degree of applicability for water treatment.

Adsorption studies of a multi-metal system within acetate media, with a view to sustainable phosphate recovery from sewage sludge

Phosphate shortages and the ensuing pressures on food security have led to an interest in processed sewage sludge as a substitute for commercial fertilisers. The presence of heavy metals in this nutrient source causes concerns around environmental release and pollution. This work builds towards a resin-in-pulp sludge detoxification process. It showcases the kinetic and thermodynamic adsorption capabilities of the ion-exchange resins C107E (carboxylic acid functionality), MTS9301 (iminodiacetic acid) and TP214 (thiourea), with respect to Cu(II), Fe(II), Pb(II) and Zn(II), within a simulated sewage sludge weak acid (acetate) leachate. The isotherms produced in this complex system were quite different to those generated when single metals were investigated in isolation, with desorption of lower affinity species clearly observed at higher equilibrium concentration values. Mixed-metal isotherm data were fitted to common two-parameter isotherm models and also a novel modified Langmuir model, which better accounted for the effects of desorption and competition. Kinetic data were also fit to common two-parameter models; results suggesting the system was likely film diffusion-controlled and followed pseudo-2nd-order kinetics. C107E displayed rapid adsorption of lead (t_1/2 = 26 ± 3min), and significant uptake of all metals. MTS9301 showed high affinity for copper ions, with concurrent desorption of all the other metals, and also displayed the fastest kinetics (t_1/2 = 14.1 ± 0.9, 130 ± 20, 25 ± 5 and 49 ± 6 min for copper, iron(II), lead and zinc, respectively). C107E and MTS9301 showed far slower adsorption for iron(II) than the other three metals, which invited the possibility of kinetic separations. TP214 had reasonable effectiveness in removal of copper, but poor affinity for all other metals. The greatest difficulty in modelling the multi-metal system was the two-stage trends observed in equilibrium experiments, as metal-proton exchanges become metal-metal exchanges. While not having the highest capacity, MTS9301 was recommended as the most appropriate resin for rapid and efficient removal of Cu, Pb and Zn from the acetate medium.

Influence of modulus of alkaline activator on the removal of Pb2+ by mesoporous geopolymer adsorbent

In this study, we synthesised metakaolin-based mesoporous geopolymer adsorbent and investigated the effect of alkaline activator modulus (molar ratios of SiO₂/Na₂O) on Pb²⁺ adsorption. The geopolymer prepared using 1.2 M alkaline activator performs excellent Pb²⁺ removal with a maximum adsorption capacity of 172.71 mg g^-1. The pseudo-second-order model fit the adsorption kinetics satisfactorily, indicating that the adsorption process is dominated by chemical adsorption. The adsorption data appropriately fit the Langmuir isotherm model. The contributions of adsorption methods corresponding to the total quantity adsorbed declined in the following order: EDTA extraction (formation of Pb aluminium oxide and Pb-containing amorphous materials) > residual fraction (Pb stabilisation in the tetrahedral aluminosilicate network) > ion exchange. Overall, the alkaline activator modulus significantly influenced the Pb²⁺ adsorption characteristics of the geopolymer adsorbent.

Functionality screening to help design effective materials for radioiodine abatement

This paper is part of a growing body of research work looking at the synthesis of an optimal adsorbent for the capture and containment of aqueous radioiodine from nuclear fuel reprocessing waste. 32 metalated commercial ion exchange resins were subjected to a two-tier screening assessment for their capabilities in the uptake of iodide from aqueous solutions. The first stage determined that there was appreciable iodide capacity across the adsorbent range (12–220 mg·g⁻¹). Candidates with loading capacities above 40 mg·g⁻¹ were progressed to the second stage of testing, which was a fractional factorial experimental approach. The different adsorbents were treated as discrete variables and concentrations of iodide, co-contaminants and protons (pH) as continuous variables. This gave rise to a range of extreme conditions, which were representative of the industrial challenges of radioiodine abatement. Results were fitted to linear regression models, both for the whole dataset (R² = 59%) and for individual materials (R² = 18–82%). The overall model determined that iodide concentration, nitrate concentration, pH and interactions between these factors had significant influences on the uptake. From these results, the top six materials were selected for project progression, with others discounted due to either poor uptake or noticeable iodide salt precipitation behaviour. These candidates exhibited reasonable iodide uptake in most experimental conditions (average of >20 mg·g⁻¹ hydrated mass), comparing favourably with literature values for metallated adsorbents. Ag-loaded Purolite S914 (thiourea functionality) was the overall best-performing material, although some salt precipitation was observed in basic conditions. Matrix effects not withstanding it is recommended that metalated thiourea, bispicolylamine, and aminomethylphosphonic acid functionalized silicas warrant further exploration.

Enhancement on the degradation of naproxen in Cu0 activated peroxymonosulfate system by complexing reagents

In recent years, there has been growing interest in the mechanism (radical or nonradical) of persulfate activation processes. In this study, the enhancement of naproxen (NPX) degradation in a Cu⁰/peroxymonosulfate (PMS) system by complexing reagents was investigated. Surprisingly, neocuproine (NCP) alters the nature of reactive species in the Cu⁰/PMS system. A high-valent copper species, Cu(III)-NCP, was found to dominate NPX degradation rather than radicals under acid conditions for the first time. Moreover, systematically designed experiments revealed that the Cu(III)-NCP complex was a strong selective oxidant that reacted with organics through a single electron transfer pathway. Meanwhile, the degradation efficiency of NPX was highly dependent on the solution pH and dosage of Cu⁰ and NCP, but was irrelevant to the concentration of NPX. Additionally, the enhancement of NCP on other copper based PMS activation systems (i.e., Cu²⁺/HA/PMS and Cu⁰/HA/PMS systems) was investigated. Considering that the released copper can be removed by a simple precipitation method to meet the effluent standards, the new complex-enhanced Cu⁰/PMS system provided a new method to enhance the degradation efficiencies of pollutants by a copper-catalyzed Fenton-like system.

Simultaneous removal of nitrate, tetracycline, and Pb(II) by iron oxidizing strain Zoogloea sp. FY6: Performance and mechanism

Based on the prevalence of combined antibiotics and heavy metals contamination in the aquatic environment, this study utilized a microbial approach to achieve simultaneous removal of nitrate (NO₃^--N), tetracycline (TTC), and Pb(II). Zoogloea sp. FY6 could achieve an optimal NO₃^--N removal efficiency of 91.5% under C/N ratio of 2.0, at a pH of 6.3, and Fe(II) concentration of 20.23 mg L^-1 based on response surface methodology. Additionally, strain FY6 was further found to achieve 89.9 and 81.7% removal of TTC and Pb(II) at 6 h under the optimal conditions. Finally, the results of Fluorescence excitation-emission matrix, X-ray diffraction, Fourier transform infrared spectrometer, and X-ray photoelectron spectroscopy further proved that the biologically formed nanoscale iron oxides and biological action jointly led to the removal of TTC and Pb(II). This study provided a theoretical basis for the application of microbially driven process to remove multi-pollutants in micro-polluted water bodies.

Removal of heavy metals from sewage sludge by chemical leaching with biodegradable chelator methyl glycine diacetic acid

The heavy metals (HMs) contained in sewage sludge are some of the largest obstacles that hamper the usage of sewage sludge in land application (e.g. fertilizer, soil improver). The conventional chelators, e.g., ethylenediaminetetraacetic acid (EDTA), were effective in the remediation of HMs polluted sewage sludge, but suffered from an evident drawback of low biodegradability. Therefore, the applicability of a new biodegradable chelator, methyl glycine diacetic acid (MGDA), to extract HMs from sewage sludge was carried out and compared with EDTA. The experimental parameters affecting the performance of MGDA were optimized. Leaching results showed that in general, MGDA exhibited higher Zn leaching efficiency and similar Cu, Ni and Cr leaching efficiencies with EDTA at same pH and dosage conditions. The maximum Zn, Cu, Ni and Cr leaching efficiencies of MGDA were 94.1% ± 4.5%, 58.2% ± 3.1%, 78.2% ± 2.3% and 54.6% ± 2.5%, respectively. The leaching efficiency plateaued within a reaction time of 4 h, but that of Cu and Ni showed a slightly decreasing trend during hours 4 to 10. In raw sewage sludge, the Zn and Cu were mainly presented in the organically bound fraction, i.e., 45.3 ± 3.2% of total Zn and 48.3 ± 1.4% of total Cu. The addition of MGDA and EDTA caused obvious distribution transformations in Zn and Cu from the organically bound fraction to soluble fraction. According to the reduced partition index calculation, the mobility of Zn, Cu, Ni, and Cr was not significantly lowered after the MGDA treatment. However, the HMs secondary pollution risk of the sludge was reduced due to the drop of the total HMs content after chelator leaching. Findings from this study suggest that MGDA could be a potential environment-friendly alternative for refractory chelators (e.g. EDTA) in the decontamination of HMs from sludge.

The Removal of Pb2+ from Aqueous Solution by Using Navel Orange Peel Biochar Supported Graphene Oxide: Characteristics, Response Surface Methodology, and Mechanism

The value-added utilization of waste resources to synthesize functional materials is important to achieve the environmentally sustainable development. In this paper, the biochar supported graphene oxide (BGO) materials were prepared by using navel orange peel and natural graphite. The optimal adsorption parameters were analyzed by response surface methodology under the conditions of solution pH, adsorbent dosage, and rotating speed. The adsorption isotherm and kinetic model fitting experiments were carried out according to the optimal adsorption parameters, and the mechanism of BGO adsorption of Pb2+ was explained using Scanning Electron Microscope (SEM-EDS), X-ray Photoelectron Spectroscopy (XPS), X-ray Diffraction (XRD), and Fourier Transform Infrared Spectroscopy (FTIR). Compared with virgin biochar, the adsorption capacity of Pb2+ on biochar supported graphene oxide was significantly increased. The results of response surface methodology optimization design showed that the order of influence on adsorption of Pb2+ was solution pH > adsorbent dosage > rotating speed. The optimal conditions were as follows: solution pH was 4.97, rotating speed was 172.97 rpm, and adsorbent dosage was 0.086 g. In the adsorption−desorption experiment, the desorption efficiency ranged from 54.3 to 63.3%. The process of Pb2+ adsorption by BGO is spontaneous and endothermic, mainly through electrostatic interaction and surface complexation. It is a heterogeneous adsorption process with heterogeneous surface, including surface adsorption, external liquid film diffusion, and intra-particle diffusion.

In Situ Synthesis of Carbon Nanotube–Steel Slag Composite for Pb(II) and Cu(II) Removal from Aqueous Solution

Methods and materials that effectively remove heavy metals, such as lead and copper, from wastewater are urgently needed. In this study, steel slag, a low-cost byproduct of steel manufacturing, was utilized as a substrate material for carbon nanotube (CNT) growth by chemical vapor deposition (CVD) to produce a new kind of efficient and low-cost absorbent without any pretreatment. The synthesis parameters of the developed CNT–steel slag composite (SS@CNTs) were optimized, and its adsorption capacities for Pb(II) and Cu(II) were evaluated. The results showed that the optimal growth time, synthesis temperature and acetylene flow rate were 45 min, 600 °C and 200 sccm (standard cubic centimeter per minute), respectively. The SS@CNTs composite had a high adsorption capacity with a maximum removal amount of 427.26 mg·g−1 for Pb(II) and 132.79 mg·g−1 for Cu(II). The adsorption proceeded rapidly during the first 15 min of adsorption and reached equilibrium at approximately 90 min. The adsorption processes were in accordance with the isotherms of the Langmuir model and the pseudo-second-order model, while the adsorption thermodynamics results indicated that the removal for both metals was an endothermic and spontaneous process. This study showed that compared with other adsorbent materials, the SS@CNTs composite is an efficient and low-cost adsorbent for heavy metals such as lead and copper.

Sustainable and efficient technologies for removal and recovery of toxic and valuable metals from wastewater: Recent progress, challenges, and future perspectives

Due to their numerous effects on human health and the natural environment, water contamination with heavy metals and metalloids, caused by their extensive use in various technologies and industrial applications, continues to be a huge ecological issue that needs to be urgently tackled. Additionally, within the circular economy management framework, the recovery and recycling of metals-based waste as high value-added products (VAPs) is of great interest, owing to their high cost and the continuous depletion of their reserves and natural sources. This paper reviews the state-of-the-art technologies developed for the removal and recovery of metal pollutants from wastewater by providing an in-depth understanding of their remediation mechanisms, while analyzing and critically discussing the recent key advances regarding these treatment methods, their practical implementation and integration, as well as evaluating their advantages and remaining limitations. Herein, various treatment techniques are covered, including adsorption, reduction/oxidation, ion exchange, membrane separation technologies, solvents extraction, chemical precipitation/co-precipitation, coagulation-flocculation, flotation, and bioremediation. A particular emphasis is placed on full recovery of the captured metal pollutants in various reusable forms as metal-based VAPs, mainly as solid precipitates, which is a powerful tool that offers substantial enhancement of the remediation processes' sustainability and cost-effectiveness. At the end, we have identified some prospective research directions for future work on this topic, while presenting some recommendations that can promote sustainability and economic feasibility of the existing treatment technologies.

A review on biofiltration techniques: Recent advancements in the removal of volatile organic compounds and heavy metals in the treatment of polluted water

Good quality of water determines the healthy life of living beings on this earth. The cleanliness of water was interrupted by the pollutants emerging out of several human activities. Industrialization, urbanization, heavy population, and improper disposal of wastes are found to be the major reasons for the contamination of water. Globally, the inclusion of volatile organic compounds (VOCs) and heavy metals released by manufacturing industries, pharmaceuticals, and petrochemical processes have created environmental issues. The toxic nature of these pollutants has led researchers, scientists, and industries to exhibit concern towards the complete eradication of them. In this scenario, the development of wastewater treatment methodologies at low cost and in an eco-friendly way had gained importance at the international level. Recently, bio-based technologies were considered for environmental remedies. Biofiltration based works have shown a significant result for the removal of volatile organic compounds and heavy metals in the treatment of wastewater. This was done with several biological sources such as bacteria, fungi, algae, plants, yeasts, etc. The biofiltration technique is cost-effective, simple, biocompatible, sustainable, and eco-friendly compared to conventional techniques. This review article provides deep insight into biofiltration technologies engaged in the removal of volatile organic compounds and heavy metals in the wastewater treatment process.

Pb(II) adsorption mechanism and capability from aqueous solution using red mud modified by chitosan

Red mud modified by chitosan (RM/CS) was utilized as an adsorbent to effectively remove Pb(II) from aqueous solution. The surface area of RM/CS was found to significantly increase by more than 50% compared to that of original red mud. Different factors that affected the Pb(II) removal on this material, such as initial Pb(II) concentration, pH, and contact time, were investigated. The pseudo-first-order, pseudo-second-order, and intra-diffusion models were used to fit the experimental data to investigate the Pb(II)'s removal kinetics. The Pb(II) removal followed the intra-diffusion model. Additionally, the non-zero C value obtained from this model indicates that the removal was controlled by many different mechanisms. We also found that the interaction of Pb(II) and carbonate group on the material's surface played a primary role once the adsorption equilibrium was reached. Finally, the maximum adsorptive capacity was found to be about 209 mg/g. This obtained value is higher than those obtained for some other materials. Therefore, the present RM/CS should be a potential material for removing Pb(II) from aqueous solution.

Mesoporous maltose/calcium oxalate hybrid material with abundant reaction sites and its efficient Pb(ii) removal from diverse water bodies

Maltose/calcium oxalate exhibits high capacity and selective adsorption of Pb(ii) due to the synergistic mechanism of ion exchange, electrostatic and complexation.

A review on adsorptive separation of toxic metals from aquatic system using biochar produced from agro-waste

Water is a basic and significant asset for living beings. Water assets are progressively diminishing due to huge populace development, industrial activities, urbanization and rural exercises. Few heavy metals include zinc, copper, lead, nickel, cadmium and so forth can easily transfer into the water system either direct or indirect activities of electroplating, mining, tannery, painting, fertilizer industries and so forth. The different treatment techniques have been utilized to eliminate the heavy metals from aquatic system, which includes coagulation/flocculation, precipitation, membrane filtration, oxidation, flotation, ion exchange, photo catalysis and adsorption. The adsorption technique is a better option than other techniques because it can eliminate heavy metals even at lower metal ions concentration, simplicity and better regeneration behavior. Agricultural wastes are low-cost biosorbent and typically containing cellulose have the ability to absorb a variety of contaminants. It is important to note that almost all agro wastes are no longer used in their original form but are instead processed in a variety of techniques to improve the adsorption capacity of the substance. The wide range of adsorption capacities for agro waste materials were observed and almost more than 99% removal of toxic pollutants from aquatic systems were achieved using modified agro-waste materials. The present review aims at the water pollution due to heavy metals, as well as various heavy metal removal treatment procedures. The primary objectives of this research is to include an overview of adsorption and various agriculture based adsorbents and its comparison in heavy metal removal.

Enhanced heavy metal leaching from sewage sludge through anaerobic fermentation and air-assisted ultrasonication

Interest in using stabilized sewage sludge in agriculture is mainly to benefit from its nutrient content, soil conditioning properties, and water holding capacity. Therefore, sludge management practice needs to be directed from treatment liability towards the recovery of chemical assets embedded in sludge. In this study, anaerobic fermentation process integrated with a new treatment method; i.e., air-assisted ultrasonication, was used to assess the leaching of heavy metals (HM) from waste activated sludge (WAS). Fermentation processes resulted in 9390 mg COD/L of volatile fatty acids (VFAs) production, 26% Ni solubilization and up to 3.4% solubilization of other target metals (Cu and Zn). Application of the air-assisted ultrasonication as a post-treatment to fermentation process stimulated the migration and transformation of HMs to the liquid fraction of the digestate. Applying specific energy input greater than 9 kJ/g total solids (TS) through ultrasonication and supplying air with constant flow rate of 0.875 L of air/(L of digestate.min) resulted in leaching of more than 83% of Ni, 82% of Cu and 80% of Zn.

Effective removal of heavy metals from water using porous lignin-based adsorbents

Multifunctional composite materials are the key to improving removal capacity and environmental utility. Here, the adsorbent (SLCA) was obtained by free-radical polymerization of acrylic acid with sodium lignosulfonate and citric acid. FTIR, SEM, TGA and XPS characterization methods were used to prove the structure and properties of SLCA adsorbents. The maximum uptake capacities of the optimized SLCA adsorbent is 276 mg g^-1 of Cu²⁺ and 323 mg g^-1 of Pb²⁺, respectively. The Langmuir isotherm and the second-order kinetic model were established to illustrate that the capture of Cu²⁺ and Pb²⁺ by the adsorbent belongs to chemisorption on the monolayer. XPS analysis confirmed that complexation and electrostatic attraction are the mechanism of pollutant removal. Not only that, as-resulting adsorbent revealed no significant adsorption cycle efficiency reduction even after 5 runs of sorption-desorption cycle, manifesting that it is of great stability and could be regarded as a promising candidate adsorbent. The purpose of this research was to develop a green lignin-based adsorbent with strong environmental protection and regeneration ability based on cheap polyacrylic resin.

Preparation and characterization of boron-doped corn straw biochar: Fe (Ⅱ) removal equilibrium and kinetics

Nowadays, iron ions as a ubiquitous heavy metal pollutant are gradually concerned and the convenient and quick removal of excessive iron ions in groundwater has become a major challenge for the safety of drinking water. In this study, boron-doped biochar (B-BC) was successfully prepared at various preparation conditions with the addition of boric acid. The as-prepared material has a more developed pore structure and a larger specific surface area (up to 897.97 m²/g). A series of characterization results shows that boric acid effectively activates biochar, and boron atoms are successfully doped on biochar. Compared with the ratio of raw materials, the pyrolysis temperature has a greater influence on the amount of boron doping. Based on Langmuir model, the maximum adsorption capacity of 800B-BC_1:2 at 25 °C, 40 °C, 55 °C are 50.02 mg/g, 95.09 mg/g, 132.78 mg/g, respectively. Pseudo-second-order kinetic model can better describe the adsorption process, the adsorption process is mainly chemical adsorption. Chemical complexation, ions exchange, and co-precipitation may be the main mechanisms for Fe²⁺ removal.

A Novel Manganese-Rich Pokeweed Biochar for Highly Efficient Adsorption of Heavy Metals from Wastewater: Performance, Mechanisms, and Potential Risk Analysis

A novel manganese-rich pokeweed biochar was prepared at different temperatures from manganese-rich pokeweed plants collected at manganese tailings, resulting in materials identified as BC300, BC400, and BC500. The synthetized biochar materials were investigated as regards their potential for removing Cu2+, Pb2+, and Cd2+, specifically in terms of adsorption performances, adsorption kinetics, adsorption isotherms, and potential environmental pollution risk. The results showed that the sorption process fitted well to the pseudo-second-order kinetic and Langmuir models, and the maximum adsorption capacities of BC500 were 246, 326, and 310 mg·g−1 for Cu2+, Pb2+, and Cd2+ respectively. The physicochemical characteristics of the biochars, and the adsorption mechanisms, were revealed by using scanning electron microscopy-energy spectrometer, elemental analysis, Brunauer–Emmett–Teller techniques, X-ray diffraction, X-ray photoelectron spectroscopy, and Fourier transform infrared spectroscopy. The sorption mechanism of these three heavy metal ions onto biochars included ion exchange, electrostatic adsorption, chemical adsorption, and precipitation. Besides, the potential pollution risk of manganese-rich pokeweed biochars was significantly reduced after pyrolysis. Therefore, it is feasible to transform manganese-rich pokeweed biomass into manganese-rich pokeweed biochar with potential for heavy metals removal, showing high adsorption capacity, recyclability, and low environmental pollution.

Use and treatment of chicken feathers as a natural adsorbent for the removal of copper in aqueous solution

PURPOSE

Copper is a heavy metal that causes considerable deterioration to human health and ecosystems, so their elimination in water bodies is of great interest. Present investigation shows the efficiency of chicken feather as a natural adsorbent and its subsequent degradation in order to have an integral treatment and avoid the unconscious disposition.

METHODS

Optimal conditions of adsorption process were determined using the Response Surface Methodology (RSM)-Box-Behnken design (BBD) with three variables (pH, temperature and adsorbent dose). After that, the optimal conditions were used to analize the adsorption isotherms by Langmuir, Freundlich and Temkin models; also thermodynamics parameters Gibbs free energy (ΔG°), enthalpy (ΔH°) and entropy (ΔS°) were obtained. Finally, the biodegradation of the residue denominated "adsorbent-adsorbate" complex was evaluated through monitoring the soluble protein production, keratinolytic activity, ninhydrin positive products, sulfhydryl groups, and gravimetrically analysis.

RESULTS

The optimum conditions for the adsorption were 30°C and pH 3, the Langmuir model was better described the adsorption process at 30°C, while at 40°C was Temkin model. The chicken feather turned out a natural adsorbent competitive with respect to others used in the removal of copper in liquid systems; obtaining qmax of 7.84 and 11.48 mg/g at 30 and 40°C, respectively; it was also a favorable and spontaneous process. Finally the adsorbent used was degraded by a keratinolytic consortium.

CONCLUSIONS

In this study, chicken feather was used as a low cost adsorbent for copper efficiently and with the feasibility that the adsorbent can be biodegraded and release the metal.

Recent developments in layer-by-layer assembled systems application in water purification

Electrostatically-based layer-by-layer (LbL) assembly is a versatile surface functionalization technique allowing the construction of complex three-dimensional architectures on virtually any type of material using various combinations of nano-bricks. One of the most promising applications of LbL assembled systems is in water purification. The main two strategies developed in this purpose consist in either enhancing the barrier properties of separation membranes and in the construction of core-shell organic/inorganic sorbents. In this review, the recent achievements in this topic are discussed with respect to the use of LbL-based composites in desalination and removal of heavy metal ions or organic pollutants. Finally, some works dealing with economic aspects of using LbL assemblies for water purification are presented, thus highlighting forthcoming strategies to develop economically-viable materials for such applications.

Effects of substrates containing different concentrations of sewage sludge on physiological parameters and quality of Alibertia edulis (Rubiaceae) seedlings

Sewage sludge (SS), a solid residue of effluent treatment, is rich in organic matter and nutrients, while also containing heavy metals and other potential contaminants. The feasibility of employing SS as a substrate component for seedling production depends on its composition and dose, as well as on the tolerance limit of individual plant species. To expand the knowledge base on the use of SS in the production of plants native to the Brazilian Cerrado biome, we evaluated the physiological responses and quality of Alibertia edulis seedlings grown under distinct SS concentrations. Chlorophyll a fluorescence (ChlF), stomatal conductance (gs), leaf temperature (Lt), biomass, growth, and seedling quality were investigated. At 25%, SS improved growth, biomass, and seedling quality, while substrates containing 50% or more SS affected gs, Lt, and ChlF. Seedling quality was strongly worsened by SS at 75% and 100%, as shown by lower biomass and impaired growth, including leaf symmetry loss and leaf deformities possibly related to contaminants, particularly heavy metals. Accordingly, we conclude that SS exhibited potential as a fertilizer at concentrations below 50%, but exerted a toxic effect on seedlings at higher concentrations.

Effect mechanism of copper ions on photocatalytic activity of TiO2/graphene oxide composites for phenol-4-sulfonic acid photodegradation

Organic pollutants in electroplating wastewater can be removed by photodegradation, however the effect mechanism of heavy metal ions on photocatalytic activity still remains unknown. Herein, we firstly reported the self-assembly synthesis of titanium dioxide/reduced graphene oxide (TiO₂/rGO) composites for phenol-4-sulfonic acid (PSA) removal, and investigated the effects of Cu²⁺ ions on photocatalytic efficiency. During the self-assemble process, rGO nanosheets were connected together to form network macropores, and simultaneously induced the deposition of hierarchically nanostructured TiO₂ microspheres. The synergetic effects of TiO₂ microspheres and rGO nanosheets improved the photocatalytic activity by enhancing light adsorption ability, stabilizing electron-hole separation and decreasing band gap energy. The Cu²⁺ ions in wastewater showed positive and negative effects on PSA photodegradation. In the photocatalytic reaction, the electron-induced reduction reaction of Cu(II) into Cu(0) or Cu(I) took place, which inhibited electron-hole recombination and thus enhanced photocatalytic activity. However, the high chemical stability of PSA-Cu(II) complex compounds held back PSA photodegradation. The appropriate concentrations of Cu²⁺ ions at around 25 mg/L accelerated PSA photodegradation over TiO₂/rGO composites. The PSA degradation into CO₂ and H₂O was performed by using hydroquinone, benzoquinone and maleic acid as degradation intermediates. Hence, TiO₂/rGO composites are novel multifunctional photocatalysts to purify electroplating wastewater.

Comprehensive comparison of acidic and alkaline anaerobic fermentations of waste activated sludge

This study conducted a comprehensive comparison of acidic (R_5.0) and alkaline (R_10.0) anaerobic fermentations of waste activated sludge (WAS). The results showed that alkaline fermentation was able to increase biopolymer release and benefitted the production of volatile fatty acids (VFAs). However, large amounts of the released organic matter in the R_10.0 fermented liquid had low biodegradability unsuitable for the biological nutrient removal (BNR) process, resulting in increased C, nitrogen, and phosphorus loads in BNR effluent. Further, Al was more readily released than other metals and its maximum concentration reached 134.52 mg/L in R_10.0, 2.99 times higher than in R_5.0. The fermented sludge filterability was severely deteriorated at R_10.0, as indicated by the normalized capillary suction time and specific resistance to filtration. Considering these findings, VFAs from WAS via acidic fermentation may represent a suitable carbon source for direct use in the BNR process.

Synthesis of sodium lignosulfonate-guar gum composite hydrogel for the removal of Cu2+ and Co2

As an emerging pollutant treatment material, hydrogel is known for its good adsorption capacity and environmental friendliness. In this study, a composite material of acrylic acid as the polymerization monomer grafted sodium lignosulfonate and guar gum was prepared, which provided a channel for adsorbing metal ions with its abundant active functional groups and porous structure. The optimized synthesized product was applied to the removal of Cu²⁺ and Co²⁺ in a one-component system and a multi-component system, and the maximum ion adsorption capacities obtained were determined to be 709 mg g^-1 of Cu²⁺, 601 mg g^-1 of Co²⁺, respectively. The adsorption kinetics and isotherms were well fitted by the pseudo second-order kinetic model and the Langmuir isotherm, showing that the adsorption of Cu²⁺ and Co²⁺ by the adsorbent belongs to the chemisorption on monolayer. XPS results confirmed the successful adsorption of Cu²⁺ and Co²⁺ by GG/SLS. Surface complexation was proposed to be the main mechanism for GG/SLS adsorbent to remove heavy metal ions. In addition, the use of recycling research showed that the adsorbent has good chemical stability. These results provided valuable information for designing highly efficient adsorbents that can be used as a high-quality wastewater treatment material.

Industrial alkali lignin-derived biochar as highly efficient and low-cost adsorption material for Pb(II) from aquatic environment

Developing a cost-effective and high-efficiency biochar is critical in various environmental applications. Lignin-based materials are natural and abundant adsorbents to heavy metals benefited from their special polyphenol structure and physicochemical properties. In this study, adsorption capacities to Pb(II) by alkali lignin (AL) and its biochar derivative (ALB) were comparatively discussed, and the latter exhibited superior adsorption performance, with a maximum adsorption capacity almost twice that of the former, and a much faster absorption rate. The q_m value of ALB was significantly superior to that of other reported biochar materials. Pb(II) was mainly adsorbed into ALB in three forms: mineral precipitation, ion exchange, and surface complexation, with complexation and mineral precipitation being the dominant mechanisms of adsorption. This study demonstrates that alkali-lignin derived biochar is a promising material for the remediation of polluted by Pb(II).