Fast determination of paraquat residues in water by an optical immunosensor and validation using capillary electrophoresis-ultraviolet detection

A ratiometric fluorescence method for the detection of diquat by a large Stokes shift fluorescent probe

Pesticide residues are currently a prominent concern for food safety, and the development of a rapid, convenient, and accurate method for detecting pesticide residues is crucial to ensure the quality of agricultural products. In this study, a small molecule fluorescent probe based on biphenyl disulfonic acid (BDSA) was designed and prepared, and a sensitive, specific, and rapid detection method for diquat (DQ) and paraquat (PQ) was developed. The fluorescent molecule (BDSA-NDA) was synthesized through amide reaction between BDSA and 1,8-naphthalic anhydride, which exhibited cyan fluorescence (480 nm) when excited at 305 nm in aqueous solution with a large Stokes shift (>150 nm). Diquat and paraquat were found to quench the fluorescence of the probe through internal filtration effect (IFE) and photoelectron transfer (PET). Moreover, diquat possessed a large conjugated structure that emitted fluorescence at 340 nm which was assembled into a pair of ratio fluorescence with BDSA-NDA. Under optimized experimental conditions, the developed method achieved detection limits of 0.003 mg/L for diquat and 0.202 mg/L for paraquat. Furthermore, it could identify paraquat doped in diquat formulations. Additionally, when applied to environmental water samples as well as rice and urine, this detection method demonstrated good recovery rates (water: 96.2-100.6 %, rice: 93.5-101.9 %, urine: 96-103.7 %), meeting actual sample detection requirements effectively. This work presents a novel approach for rapidly detecting diquat and paraquat residues which holds practical application value in areas such as pesticide residue analysis in foods, environmental or clinical samples.

Paraquat exposure induces Parkinsonism by altering lipid profile and evoking neuroinflammation in the midbrain

Paraquat (PQ) is the most widely used herbicide in the world and a well-known potent neurotoxin for humans. PQ exposure has been linked to increase the risk of Parkinson's disease (PD). However, the mechanism underlying its neurotoxic effects in PD pathogenesis is unclear. In our present study, C57BL/6J mice treated with PQ manifested severe motor deficits indicated by the significant reductions in suspension score, latency to fall from rotarod, and grip strength at 8 weeks after PQ exposure. Pathological hallmarks of Parkinsonism in the midbrain such as dopaminergic neuron loss, increased α-synuclein protein, and dysregulated PD-related genes were observed. Non-targeted lipidome analysis demonstrated that PQ exposure alters lipid profile and abundance, increases pro-inflammatory lipids.27 significantly altered subclasses of lipids belonged to 6 different lipid categories. Glycerophospholipids, sphingolipids, and glycerides were the most abundant lipids. Abundance of pro-inflammatory lipids such as Cer, LPC, LPS, and LPI was significantly increased in the midbrain. mRNA expressions of genes regulating ceramide biosynthesis in the midbrain were markedly up-regulated. Moreover, PQ exposure increased serum pro-inflammatory cytokines and provoked neuroinflammation in the midbrain. Pro-inflammatory lipids and cytokines in the midbrain were positively correlated with motor deficits. PQ poisoning in humans significantly also elevated serum pro-inflammatory cytokines and induced an intense systemic inflammation. In summary, we presented initial investigations of PQ induced molecular events related to the PD pathogenesis, capturing aspects of disturbed lipid metabolism, neuroinflammation, impairment of dopaminergic neurons in the midbrain, and an intense systemic inflammation. These neurotoxic effects of PQ exposure may mechanistically contribute to the pathogenesis of PQ induced Parkinsonism. Results of this study also strongly support the hypothesis that ever-increasing prevalence of Parkinson's disease is etiologically linked to the health risk of exposure to neurotoxic environmental pollutants.

Ready-to-use paraquat sensor using a graphene-screen printed electrode modified with a molecularly imprinted polymer coating on a platinum core

We propose the fabrication of a novel ready-to-use electrochemical sensor based on a screen-printed graphene paste electrode (SPGrE) modified with platinum nanoparticles and coated with a molecularly imprinted polymer (PtNPs@MIP) for sensitive and cost-effective detection of paraquat (PQ) herbicide. Successive coating of the PtNPs surface with SiO₂ and vinyl end-groups formed the PtNPs@MIP. Next, we terminated the vinyl groups with a molecularly imprinted polymer (MIP) shell. MIP was attached to the PtNPs cores using PQ as the template, methacrylic acid (MAA) as the monomer, ethylene glycol dimethacrylate (EGDMA) as the cross-linker, and 2,2'-azobisisobutyronitrile (AIBN) as the initiator. Coating the SPGrE surface with PtNPs@MIP furnished the PQ sensor. We studied the electrochemical mechanism of PQ on the MIP sensor using cyclic voltammetry (CV) experiments. The PQ oxidation current signal appears at -1.08 V and -0.71 V vs. Ag/AgCl using 0.1 M potassium sulfate solution. Quantitative analysis was performed by anodic stripping voltammetry (ASV) using a deposition potential of -1.4 V for 60 s and linear sweep voltammetric stripping. The MIP sensor provides linearity from 0.05 to 1000 μM (r² = 0.999), with a lower detection limit of 0.02 μM (at -0.71 V). The compact imprinted sensor gave a highly sensitive and selective signal toward PQ. The ready-to-use MIP sensor can provide an alternative approach to the determination of paraquat residue on vegetables and fruits for food safety applications.

Monitoring of Paraquat in soya products intended for animal feed

Even though paraquat is considered to be one of the most toxic herbicides, it is one of the most used ones. Paraquat-based preparations are heavily used across many important agricultural countries and for a lot of types of crops such as soya. As soya is used in large quantities in the feed production, paraquat residues in soya products are a potential threat to livestock. The aim of this study was to investigate whether soya products intended for animal feed contain residues of paraquat. Therefore, an optimized Quick Polar Pesticides (QuPPe) Method was developed. In total, 174 samples were analyzed via LC-MS/MS using zwitterionic hydrophilic interaction liquid chromatography (ZIC-HILIC). The results showed that paraquat was detected in 66 % of the samples above 0.008 mg/kg. Residues were mainly present in soya bean meals that were imported from Brazil or the USA and cultivated using genetically modified soya. Around 5 % of the samples were not compliant with the European regulation on maximum residue levels of pesticides in or on food and feed. The results of this study support the view that paraquat residues play a significant role in soya products intended for animal feed and, thus, need to be controlled on a regular basis. However, for enforcement actions reliable processing factors for paraquat in soya products or maximum residue levels for processed soya products are urgently required.

Selection of an artificial paraquat-specific binding protein from a ribosome display library based on a lipocalin scaffold

In this study, an anticalin that could specifically bind paraquat (PQ), a quaternary nitrogen herbicide, as a new set of engineered receptor protein with antibody-like properties was generated to detect PQ concentration. To this end, a native and random library was constructed and engineered to allow in vitro transcription and translation using an Escherichia coli lysate system. Meanwhile, a PQ derivative that carries an active aliphatic carboxylate group at the end of an aliphatic spacer arm was synthesized. Then, this compound was coupled covalently to the carrier protein bovine serum albumin/ovalbumin and amino-functionalized paramagnetic beads. Alternating selection in solution and immobilization in microtiter wells were used to pan mRNA-ribosome-antibody complexes. After several rounds of ribosome display, three variants were selected from a random library of the bilin-binding protein. The variants that could bind complex PQ with high affinity and exhibit IC₅₀ values as low as 14.039 ± 0.970 ng/mL were identified. Moreover, the limits of detection reached 0.083 ± 0.011 ng/mL. Our data suggest that the generation of anticalins may provide a promising alternative to recombinant antibody fragments to create a stable receptor protein against hapten with bioanalytical relevance.

Linear tri-pillar[5]arene-based acceptor for efficiently separate paraquat from water through collaboration effect

Paraquat, one of non-selective herbicides, is widely used in agricultural production. However, it can cause death of people or animals quickly owing to its fatal toxicity. In the present work, for efficient separation and removal of the paraquat, a concept "employ collaboration effect to enhance the Host-Guest interactions" was rationally introduced into the design of paraquat adsorbent material. According to this concept, a novel linear tri-pillar[5]arene-based acceptor molecule was synthesized. Interestingly, the acceptor shows outstanding adsorption properties for paraquat through the collaboration effect of the adjacent pillar[5]arene moieties in the linear tri-pillar[5]arene acceptor. Compared with other adsorbents such as activated carbon and single-pillar[5]arene-based adsorbent materials, the linear tri-pillar[5]arene acceptor shows higher adsorption rate for paraquat. Additionally, the linear tri-pillar[5]arene acceptor was applied to adsorb the commercial pesticide paraquat sample in water with adsorption rate of 98%. Therefore, the linear tri-pillar[5]arene acceptor could serve as a paraquat adsorbent material and convey greatly potential application in the field of removal of paraquat. The concept "employ collaboration effect to enhance the Host-Guest interactions" is a useful way for the development of adsorption materials.

Supramolecular Solvent-Based Liquid Phase Microextraction Combined with Ion-Pairing Reversed-Phase HPLC for the Determination of Quats in Vegetable Samples

In this study, we used anion supramolecular solvent (SUPRAS) prepared from a mixture of an anionic surfactant, sodium dodecyl sulfate (SDS), and a cationic surfactant, tetrabutylammonium bromide (TBABr), as the extraction solvent in liquid phase microextraction (LPME) of paraquat (PQ) and diquat (DQ). The enriched PQ and DQ in the SUPRAS phase were simultaneously analyzed by ion-pairing reversed-phase high performance liquid chromatography. PQ and DQ were successfully extracted by LPME via electrostatic interaction between the positive charge of the quats and the negative charge of SUPRAS. PQ, DQ, and ethyl viologen (the internal standard) were separated within 15 min on a C18 column, with the mobile phase containing 1-dodecanesulfonic acid and triethylamine, via UV detection. The optimized conditions for the extraction of 10 mL aqueous solution are 50 μL of SUPRAS prepared from a mixture of SDS and TBABr at a mole ratio of 1:0.5, vortexed for 10 s at 1800 rpm, and centrifugation for 1 min at 3500 rpm. The obtained enrichment factors were 22 and 26 with limits of detection of 1.5 and 2.8 µg L^-1 for DQ and PQ, respectively. The precision was good with relative standard deviations less than 3.86%. The proposed method was successfully applied for the determination of PQ and DQ in vegetable samples and recoveries were found in the range of 75.0% to 106.7%.

A novel electrochemical sensor based on Au nanoparticles/8-aminoquinoline functionalized graphene oxide nanocomposite for paraquat detection

In this paper, a novel electrochemical sensor based on Au nanoparticles/8-aminoquinoline functionalized graphene oxide (AuNPs/GAQ) nanocomposite was developed and tested for the first time for detection of paraquat (PQ). The morphology and composition of AuNPs/GAQ nanocomposite were characterized by various techniques, including transmission electron microscopy, Fourier transform infrared spectroscopy, Raman spectroscopy, and x-ray photoelectron spectroscopy. Cyclic voltammetry and differential pulse voltammetry were utilized to investigate the electrochemical performances of AuNPs/GAQ nanocomposite modified glassy carbon electrode. The obtained modified electrode exhibited excellent electrocatalytic activity towards detection of PQ. Under the optimized conditions, the proposed sensor showed low detection limit (6 nM, S/N = 3), wide linear range (0.02-24 μM), high selectivity and good stability. In addition, it was successfully applied for detection of PQ in natural water samples with satisfactory results.

Simultaneous determination of paraquat and atrazine in water samples with a white light reflectance spectroscopy biosensor

An optical immunosensor based on White Light Reflectance Spectroscopy for the simultaneous determination of the herbicides atrazine and paraquat in drinking water samples is demonstrated. The biosensor allows for the label-free real-time monitoring of biomolecular interactions taking place onto a SiO₂/Si chip by transforming the shift in the reflected interference spectrum due to reaction to effective biomolecular layer thickness. Dual-analyte determination is accomplished by functionalizing spatially distinct areas of the chip with protein conjugates of the two herbicides and scanning the surface with an optical reflection probe. A competitive immunoassay format was adopted, followed by reaction with secondary antibodies for signal enhancement. The sensor was highly sensitive with detection limits of 40 and 50 pg/mL for paraquat and atrazine, respectively, and the assay duration was 12 min. Recovery values ranging from 90.0 to 110% were determined for the two pesticides in spiked bottled and tap water samples, demonstrating the sensor accuracy. In addition, the sensor could be regenerated and re-used at least 20 times without significant effect on the assay characteristics. Its excellent analytical performance and short analysis time combined with the small sensor size should be helpful for fast on-site determinations of these analytes.

Supramolecular fluorescent sensor array for simultaneous qualitative and quantitative analysis of quaternary ammonium herbicides

A supramolecular fluorescent sensor array was firstly used to simultaneously qualitatively and quantitatively analyze quaternary ammonium herbicides.

Clinical screening of paraquat in plasma samples using capillary electrophoresis with contactless conductivity detection: Towards rapid diagnosis and therapeutic treatment of acute paraquat poisoning in Vietnam

The employment of a purpose-made capillary electrophoresis (CE) instrument with capacitively coupled contactless conductivity detection (C⁴D) as a simple and cost-effective solution for clinical screening of paraquat in plasma samples for early-stage diagnosis of acute herbicide poisoning is reported. Paraquat was determined using an electrolyte composed of 10mM histidine adjusted to pH 4 with acetic acid. A detection limit of 0.5mg/L was achieved. Good agreement between results from CE-C⁴D and the confirmation method (HPLC-UV) was obtained, with relative errors for the two pairs of data better than 20% for 31 samples taken from paraquat-intoxicated patients. The results were used by medical doctors for identification and prognosis of acute paraquat poisoning cases. The objective of the work is the deployment of the developed approach in rural areas in Vietnam as a low-cost solution to reduce the mortality rate due to accidental or suicidal ingestion of paraquat.

A host–guest complexation based fluorescent probe for the detection of paraquat and diquat herbicides in aqueous solutions

A new method based on fluorescence quenching of host–guest complexation was proposed for the determination of the two herbicides in river water and cabbages. The method is rapid, direct and simple.

Fast determination of paraquat in plasma and urine samples by solid-phase microextraction and gas chromatography-mass spectrometry

A simple, sensitive and reliable gas chromatographic-mass spectrometric method (GC-MS) for quantifying paraquat concentration in biological samples has been developed, using ethyl paraquat as an internal standard. The method involved the procedures of sodium borohydride-nickel chloride (NaBH4-NiCl2) reduction and solid-phase microextraction (SPME) of the perhydrogenated products. GC-MS was used to identify and quantify the analytes in selected ion monitoring (SIM) mode. Under the optimal conditions, recoveries in plasma and urine samples were 94.00-99.85% and 95.00-100.34%, respectively. Excellent sample clean-up was observed and good linearities (r=0.9982 for plasma sample and 0.9987 for urine sample) were obtained in the range of 0.1-50μg/mL. The limits of detection (S/N=3) were 0.01μg/mL in plasma and urine samples. The intra-day precision was less than 8.43%, 4.19% (n=3), and inter-day precision was less than 10.90%, 10.49% (n=5) for plasma and urine samples, respectively. This method was successfully applied to the analysis of the biological samples collected from a victim who died as a result of ingestion of paraquat.

An electrochemical magneto immunosensor (EMIS) for the determination of paraquat residues in potato samples

An electrochemical magneto immunosensor for the detection of low concentrations of paraquat (PQ) in food samples has been developed and its performance evaluated in a complex sample such as potato extracts. The immunosensor presented uses immunoreagents specifically developed for the recognition of paraquat, a magnetic graphite-epoxy composite (m-GEC) electrode and biofunctionalized magnetic micro-particles (PQ1-BSAMP) that allow reduction of the potential interferences caused by the matrix components. The amperometric signal is provided by an enzymatic probe prepared by covalently linking an enzyme to the specific antibodies (Ab198-cc-HRP). The use of hydroquinone, as mediator, allows recording of the signal at a low potential, which also contributes to reducing the background noise potentially caused by the sample matrix. The immunocomplexes formed on top of the modified MP are easily captured by the m-GEC, which acts simultaneously as transducer. PQ can be detected at concentrations as low as 0.18 ± 0.09 μg L(-1). Combined with an efficient extraction procedure, PQ residues can be directly detected and accurately quantified in potato extracts without additional clean-up or purification steps, with a limit of detection (90% of the maximum signal) of 2.18 ± 2.08 μg kg(-1), far below the maximum residue level (20 μg kg(-1)) established by the EC. The immunosensor presented here is suitable for on-site analysis. Combined with the use of magnetic racks, multiple samples can be run simultaneously in a reasonable time.

Determination of paraquat in water samples using a sensitive fluorescent probe titration method

Paraquat (PQ), a nonselective herbicide, is non-fluorescent in aqueous solutions. Thus, its determination through direct fluorescent methods is not feasible. The supramolecular inclusion interaction of PQ with cucurbit[7]uril was studied by a fluorescent probe titration method. Significant quenching of the fluorescence intensity of the cucurbit[7]uril-coptisine fluorescent probe was observed with the addition of PQ. A new fluorescent probe titration method with high selectivity and sensitivity at the ng/mL level was developed to determine PQ in aqueous solutions with good precision and accuracy based on the significant quenching of the supramolecular complex fluorescence intensity. The proposed method was successfully used in the determination of PQ in lake water, tap water, well water, and ditch water in an agricultural area, with recoveries of 96.73% to 105.77%. The fluorescence quenching values (deltaF) showed a good linear relationship with PQ concentrations from 1.0 x 10(-8) to 1.2 x 10(-5) mol/L with a detection limit of 3.35 x 10(-9) mol/L. In addition, the interaction models of the supramolecular complexes formed between the host and the guest were established using theoretical calculations. The interaction mechanism between the cucurbit[7]uril and PQ was confirmed by 1H NMR spectroscopy.

Advantages and limitations of on-line solid phase extraction coupled to liquid chromatography–mass spectrometry technologies versus biosensors for monitoring of emerging contaminants in water

On-line solid phase extraction (SPE) coupled to liquid chromatography-mass spectrometry (LC-MS) and biosensors are advanced technologies that have found increasing application in the analysis of environmental contaminants although their application to the determination of emerging contaminants (previously unknown or unrecognized pollutants) has been still limited. This review covers the most recent advances occurred in the areas of on-line SPE-LC-MS and biosensors, discusses and compares the main strengths and limitations of the two approaches, and examines their most relevant applications to the analysis of emerging contaminants in environmental waters. So far, the on-line configuration most frequently used has been SPE coupled to liquid chromatography-(tandem) mass spectrometry. Sorbents used for on-line SPE have included both traditional (alkyl-bonded silicas and polymers) and novel (restricted access materials (RAMs), molecularly imprinted synthetic polymers (MIPs), and immobilized receptors or antibodies (immunosorbents) materials. The biosensor technologies most frequently applied have been based on the use of antibodies and, to a lesser extent, enzymes, bacteria, receptors and DNA as recognition elements, and the use of optical and electrochemical transducing elements. Emerging contaminants investigated by means of these two techniques have included pharmaceuticals, endocrine disrupting compounds such as estrogens, alkylphenols and bisphenol A, pesticides transformation products, disinfection by-products, and bacterial toxins and mycotoxins, among others. Both techniques offer advantageous, and frequently comparable, features such as high sensitivity and selectivity, minimum sample manipulation, and automation. Biosensors are, in addition, relatively cheap and fast, which make them ideally suited for routine testing and screening of samples; however, in most cases, they can not compete yet with on-line SPE procedures in terms of accuracy, reproducibility, reliability (confirmation) of results, and capacity for multi-analyte determination.

An oxidative stress-specific bacterial cell array chip for toxicity analysis

An oxidative stress-specific bacterial cell array chip was fabricated and implemented in the analysis of various different chemicals. The chip consisted of twelve toxicity responsive strains that respond specifically to different oxidative toxicities such as the generation of the superoxide radical, except for strain EBMalK, which was included as a negative control. Each bioluminescent strain carried a fusion of a stress gene promoter (sodA, pqi-5, soxR, fumC, soxS, inaA, hmp, malK, katG, zwf, fpr or pgi) to the bacterial lux reporter genes. A total of nine chemicals were selected to exhibit the capabilities of this array when analyzing different oxidative toxicities. Each of the chemicals were categorized according to their structure and their ability to form radicals in vivo: (I) paraquat, an active radical producer, (II) structural analogs of paraquat that produce radicals, (III) chemicals that are distinct from paraquat but still produce radicals and (IV) chemicals having similar structures as paraquat but do not produce radicals. The results found that each strain was responsive to one or more of the compounds tested but, as a definitive factor, the responses from the chip were dependent upon the production of radicals, i.e., the strains were unresponsive to compounds that were similar in structure to paraquat but lacked the ability to generate radicals. The specificity of the strains used in the chip was also demonstrated by their ability to discriminate between the superoxide radical and hydrogen peroxide. Therefore, this cell array chip could be implemented in characterizing and understanding the toxic impacts of newly synthesized chemicals and drugs in terms of toxicity classification and the nature of oxidative damage experienced by cells.

Biosensors as useful tools for environmental analysis and monitoring

Recent advances in the development and application of biosensors for environmental analysis and monitoring are reviewed in this article. Several examples of biosensors developed for relevant environmental pollutants and parameters are briefly overviewed. Special attention is paid to the application of biosensors to real environmental samples, taking into consideration aspects such as sample pretreatment, matrix effects and validation of biosensor measurements. Current trends in biosensor development are also considered and commented on in this work. In this context, nanotechnology, miniaturisation, multi-sensor array development and, especially, biotechnology arise as fast-growing areas that will have a marked influence on the development of new biosensing strategies in the near future.

Analysis of bisphenol A in natural waters by means of an optical immunosensor

This work describes a very simple, fast and sensitive method based on the use of the optical immunosensor "RIver ANAlyser" (RIANA) to the determination of bisphenol A in a waters. RIANA is based on a rapid solid-phase indirect inhibition immunoassay that takes place at an optical transducer chip chemically modified with an analyte derivative. Fluorescence produced by labelled antibodies bound to the transducer is detected by photodiodes and can be correlated with the analyte concentration. The sensor surface can be regenerated thus allowing the performance of several measurements (around 300) with the same transducer. Each test cycle, including one regeneration step, is accomplished in 15 min. The detection limit achieved in the direct determination of bisphenol A in water with this system was 0.014 microg/L. Satisfactory repeatability, with relative standard deviations (RSD) ranging between 1.48% and 6.93% were obtained. The immunosensor method developed was applied to the monitoring of bisphenol A in various types of water collected in a waterworks (from the river water source to the finished drinking water) and validated against the results obtained in the same approach by a more traditional method, based on solid-phase extraction followed by liquid chromatography-mass spectrometry. Results obtained by both techniques were in general good agreement (considering the typical overestimation bias of immunoassays), and served to prove the satisfactory removal efficiency of the overall purification process applied in the waterworks and, in particular, of the sand filtration step.

Biosensors for marine applications. We all need the sea, but does the sea need biosensors?

The aim of the paper is to explain the rationale behind marine biosensor applications, give an overview of measurement strategies currently employed, summarise some of the relevant available biosensor technology as well as instrumentation requirements for marine sensors and attempt a forward look at what the future might hold in terms of needs and developments. Application areas considered are eutrophication, organism detection, food safety, pollutants, trace metals and ecotoxicology. The drivers for many of these studies are discussed and the policy environment for current and future measurements is outlined.

Sensing the sea

The development of the 'ecosystem approach' to the management of marine systems is leading to a requirement for data to be collected with greater frequency and spatial resolution than has been necessary in the past. This is being met both by the analysis of more samples (to better describe variability and temporal change) and by the deployment of instrumented platforms that gather data over long time periods. To meet these requirements in the hostile conditions at sea, a range of sensors based on physical, chemical and biological responses is being developed. These sensors have applications in laboratory analysis of collected samples, during field studies and directly in situ at remote sites for real-time observations of environmental trends. Here, we consider the role that biosensors could have in future marine monitoring programmes.

Ultrasensitive quantitative determination of paraquat: application to river, ground, and drinking water analysis in an agricultural area

The water specimens were collected from wells and irrigation ditches in the agricultural area to the south of Milan and from Olona River and Mantua Lake and analyzed for paraquat detection. The assay was performed using a specific polyclonal antibody raised in sheep and rabbit anti-sheep IgG conjugated with a chelating molecule 4,7-bis(chlorosulfophenyl)-1,10-phenanthroline-2,9-dicarboxylic acid complexed with Eu3+ as a fluorescent marker. Bovine serum albumin conjugated with 5-(1'-methyl[4,4']bipyridinyl-1-yl)pentanoic acid was used in solid phase preparation. The sensitivity achieved was 20 ng L(-1). The recovery in samples spiked with three different PQ concentrations was between 88 and 108%.

Simultaneous multi-analyte determination of estrone, isoproturon and atrazine in natural waters by the RIver ANAlyser (RIANA), an optical immunosensor

In most medical and environmental applications of biosensors, only single analytes are determined. However, the monitoring of several analytes is obviously preferable in order to gather more information about the sample under analysis. In line with this, different technologies are being developed to obtain multi-analyte sensors. In this paper, an analytical method for the simultaneous determination of three different contaminants-atrazine, isoproturon, and estrone-in natural waters by using an optical immunosensor prototype, the so-called "RIver ANAlyser" (RIANA), is described. RIANA is based on a rapid solid-phase fluoroimmunoassay that takes place at an optical transducer chip. The transducer surface is chemically modified with three analytes derivatives placed in different discrete locations. The sensor surface can be regenerated thus allowing the performance of several measurements with the same transducer. Each test cycle, including one regeneration step, is accomplished in 15 min. Detection limits achieved were 0.155, 0.046, and 0.084 microg/l, for atrazine, isoproturon, and estrone, respectively. Satisfactory repetition, with relative standard deviations between 1.06 and 6.98%, was obtained. Excluding a minor non-specifical binding of the isoproturon antibodies, no cross-reactivity effects were observed. Matrix effects were significant only in the case of wastewater samples. Biosensor measurements were validated using conventional liquid chromatography-mass spectrometry. The results obtained with both techniques were in good agreement.

Overview of the status and applications of capillary electrophoresis to the analysis of small molecules

The status of capillary electrophoresis (CE) in the analysis of small molecules is reviewed and summarised with the illustrative use of recent literature references. Examples are cited in this review which demonstrate that CE is now a recognised and established technique in many industries, law courts and government regulatory agencies. Each of the principal areas of CE application in small molecule analysis are covered in sections which highlight the recent developments and possibilities within that area. Application areas include the analysis of pharmaceuticals, agrochemicals, chiral separations, and forensics is covered. This is an update to a previous review article [J. Chromatogr. A 856 (1999) 443] and covers papers published between 1999 and 2002. Technical developments and improvements, such as the advent of capillary array instrumentation for increased sample throughput, and improved detection options are described. Overall it is concluded that CE has become a recognised and established technique in many areas and is still within a period of development of both instrumentation and application which will continue to expand usage.

Simultaneous determination of pesticides using a four-band disposable optical capillary immunosensor

The development of a four-band capillary optical immunosensor for the simultaneous determination of mesotrione, hexaconazole, paraquat, and diquat is described. Four distinct bands (each corresponding to a different analyte) are created in the internal walls of a plastic capillary by immobilizing protein conjugates of the analytes. To perform the assay, the capillary is filled with a mixture of anti-analyte-specific antibodies together with a standard or sample containing the analyte(s). After a short incubation, a mixture of the appropriate second antibodies labeled with fluorescein is introduced into the capillary. To measure the fluorescence intensity bound onto each band, the capillary was scanned, perpendicularly to its axis, by a laser light beam. Part of the emitted photons were trapped into the capillary walls and waveguided to a photomultiplier placed at the one end of the capillary. The analytical characteristics of the assays of mesotrione, paraquat, diquat, and hexaconazole were as follows: detection limits of 0.04, 0.06, 0.09, and 0.10 ng/mL, respectively; dynamic ranges up to 9, 6, 12, and 15 ng/ mL, respectively, intra- and interassay CVs less than 10%. The analytical characteristics of the assays were comparable with those of the corresponding single-analyte fluoroimmunoassays performed in microtitration wells, proving the ability of the proposed immunosensor for reliable multianalyte determinations. Moreover, the combination of low-cost disposable plastic capillary tubes with the low consumption of reagents, the short assay time, and the multianalyte feature of the proposed immunosensor indicates its potential for environmental analysis.

Biosensors for rapid monitoring of primary-source drinking water using naturally occurring photosynthesis

Working with primary-source freshwater drinking samples from the Clinch and Tennessee Rivers, we have developed a tissue-based biosensor detection system that uses naturally occurring aquatic photosynthetic tissue as the sensing material for detection of chemical antagonists in the water. Sensor readout is based on well-known principles of fluorescence induction by living photosynthetic tissue. The Clinch River is the main source of drinking water for Oak Ridge, Tennessee, while the Tennessee River is a major source for the city of Knoxville. We have successfully detected algae in every sample that we examined and readily monitored changes in the characteristic fluorescence induction curves when the samples were exposed to potassium cyanide (KCN), methyl parathion (MPt), N'(3,4-dichlorophenyl)-N,N-dimethylurea (DCMU), and paraquat. The percentage decreases in photochemical yields observed in Tennessee River samples after a 24-min exposure to KCN, MPt, and DCMU were, respectively, 21.89+/-0.76, 3.28+/-0.18, and 14.77+/-1.81. For a site at the Clinch River, the percentage decreases were 22.78+/-1.63, 8.32+/-0.21, and 17.71+/-1.32 (Table 1). The unique aspect of this approach to real-time water quality monitoring is that unlike conventional sensing devices, this sensor material is external to the detecting instrument and is continuously refreshed. These biosensors may be used as continuous rapid-warning sentinels for detection of chemical warfare agents in sunlight-exposed drinking water supplies.

Biosensors for marine pollution research, monitoring and control

Measurement of ecological, climatic and anthropogenic changes underpins the formulation of effective management strategies for sustainable use and protection of the marine environment. Sensors are traditionally used in marine studies to determine physical parameters, but there is increasing demand for real-time information about chemical and biological parameters. These parameters are currently measured in samples collected at sea and subsequently analysed in the laboratory. Biosensors fuse the exquisite sensitivity and specificity of living systems with the processing power of microelectronics to deliver simple, inexpensive measurement systems for use in the field or deployment in situ. While their potential for use in the marine environment is enormous, much published work to date has focussed on applications in freshwater and wastewater. Marine applications pose a substantial challenge in the robustness required for remote application, but recent developments in portable medical devices and receptor design suggest that these demands can now be realistically tackled.