Thermal cycling procedures for laboratory testing of dental restorations

Influence of Access Cavities on Maxillary Central Incisor Fracture Resistance: Finite Element Study

INTRODUCTION AND AIMS

Altering the position and orientation of the root canal access cavity passway, or modifying the reduction of dentin volume, can influence the strength of dentition. This study aimed to compare the effects of different access cavities on the biomechanical performances of maxillary central incisors with a finite element analysis.

METHODS

Based on the micro-computed tomography (CT) scan of a maxillary central incisor, the finite element models of the intact tooth and teeth with 4 access cavity designs: conservative incisal access cavity, incisal access cavity, conservative access cavity, and traditional access cavity were generated. Simulated occlusal forces were applied at the incisal edge of the incisor in the finite element analysis procedure.

RESULTS

The maximum von Mises stress and maximum principal stress in the cervical area are highest in the traditional access cavity group, followed by the conservative access cavity group, incisal access cavity group, and conservative incisal access cavity group.

CONCLUSION

The conservative access cavities minimise the extent of dentin removal from the cervical region, protecting the mechanical behaviour of the incisor. Moving the access cavity entry point to the incisal edge also improves the fracture resistance of the incisor.

CLINICAL RELEVANCE

This study's findings would help clinicians select the most appropriate endodontics access cavity method when performing the root canal on maxillary central incisors.

Microtensile Bond Strength and Failure Mode of Different Universal Adhesives on Human Dentin

AIM

The aim of this study was to compare the microtensile bond strength (µTBS) and failure mode of 4 different universal adhesive systems (UAs) on human dentin.

MATERIALS AND METHODS

The study sectioned the occlusal thirds of 32 human third molars and divided them into 4 groups based on the adhesive system used. Group A: Palfique Universal Bond, Group B: Single Bond Universal, Group C: All-Bond Universal, and Group D: One Coat 7 Universal. The specimens underwent a 10,000-cycle thermocycling ageing process prior to testing (n = 32). Afterwards, 8 beams were obtained per group and subjected to µTBS testing using a digital universal testing machine at a speed of 1 mm/min. The microtensile bond strength values were analysed in Megapascals (MPa), and the failure mode was evaluated using a stereomicroscope. Welch's parametric ANOVA with robust variance and the Games-Howell post hoc test were used for µTBS comparisons, and Fisher's exact test was used to determine the association between adhesive type and failure mode. The significance level was set at P < .05.

RESULTS

Group D showed a significantly higher µTBS than groups A (P < .001) and B (P < .001), but no significant difference was observed with group C (P= .075). Furthermore, groups B and C showed significantly higher µTBS than group A (P< .001 and P < .001, respectively), but there was no significant difference between groups B and C (P = .132). Additionally, group A exhibited a significant association with an adhesive failure mode (P < .05), whereas groups B, C, and D were significantly associated with a mixed failure mode (P < .05).

CONCLUSION

The One Coat 7 Universal adhesive system showed higher microtensile bond strength values and higher chemical interaction with dentin compared to Palfique Universal Bond and Single Bond Universal. However, no significant differences were observed compared to All-Bond Universal.

Bonding effectiveness of multi-step adhesive resin cements to CAD/CAM blocks: impact of thermal cycling and surface treatment methods

BACKGROUND

To investigate the effects of thermal cycling and surface treatment methods on the bonding effectiveness of multi-step resin cements to CAD/CAM blocks.

METHODS

A total of 198 slices, 66 each from CAD/CAM blocks (feldspathic ceramic: Vitablocs TriLuxe Forte, V; resin matrix ceramics (RMCs): Cerasmart, C; and Shofu Block HC, S), were obtained and randomly divided into two subgroups for etching with hydrofluoric acid (HFA) and sandblasting with Al2O3 (SB). After the surface treatments, one etched and one sandblasted sample of each CAD/CAM block was observed via SEM analysis at 500× magnification. The remaining 32 etched and 32 sandblasted samples of each CAD/CAM block were divided into two subgroups to be cemented with total-etch (TE) and self-etch (SE) resin cements. Then, half of the 16 samples in all the subgroups were subjected to aging (TC) for 5000 cycles (n = 8). The shear bond strength (SBS) of each sample was measured. Four-way analysis of variance (ANOVA) and Tukey tests were used to analyze the data (p < 0.05).

RESULTS

With or without TC, the highest SBS values for V were obtained with the HFA-TE and HFA-SE interactions, respectively. C presented the highest SBS values with HFA-SE and SB-TE interactions, whereas S presented the highest SBS values with SB-TE and HFA-TE interactions. Except the SB-SE interaction, C presented lower SBS values after TC than other materials. HFA created less porosity on the C and S surfaces than V. SB visibly roughened the surfaces of all the materials but caused fractures, cracks, and damage to the surfaces.

CONCLUSION

Similar SBS values can be achieved between feldspathics, RMCs, and multi-step adhesive resins with both HFA and SB treatments. However, the SBS values obtained from the SB-SE interaction may be below the recommended threshold values for all materials after TC. SB can cause distinctive cavities, fissures, and damage, especially on the surfaces of RMCs.

Bond strength of resin-based restorative materials to fast-setting calcium silicate cement using different resin adhesive systems

This study assessed the bond strength of resin-based restorative materials to fast-setting calcium silicate cement (Aarhus Uinversity, Denmark) when treated with each of two one-bottle universal adhesive systems. The cement surface (N = 256) was treated with a self-priming adhesive and a self-etch phosphate monomer-containing adhesive with and without etching of the cement surface. Specimens then received either resin composite or compomer restorative materials (n = 32). The bond strength was measured after 1 day and 1500 thermocycles (n = 16). The failure type was visually inspected. The cement-adhesive-restorative material interface was visualized using scanning electron microscopy (SEM). The data were analyzed using multiple linear regression. Restorative material type, resin adhesive system, and thermocycling had a statistically significant effect on the bond strength. Compomer restorative material and self-etch universal adhesive system demonstrated statistically significantly higher bond strength values to fast-setting calcium silicate cement, predominantly exhibiting cement cohesive failure. Etching the cement surface enhanced the bond strength of the self-priming universal adhesive. Thermocycling significantly reduced the bond strength. SEM showed self-etch universal adhesive seemingly diffused over the etched cement surface compared to other groups. Self-etch phosphate monomer-containing universal adhesive and compomer resulted in the highest bond strength to fast-setting calcium silicate cement.

Influence of 3D printing system, postpolymerization and aging protocols on resin flexural strength and dimensional stability for printing occlusal splints, models and temporary restorations

OBJECTIVES

Investigate the effect of different postpolymerization protocols, aging, and 3D printing systems on the flexural strength (σ), dimensional stability, and roughness of resins used to fabricate occlusal splints, dental models, and temporary restorations.

MATERIAL AND METHODS

180 bars (25 × 2 x 2 mm-ISO 4049) of each type of resin (T-Temporary/Cosmos Temp, Yller; OS-Occlusal splint/Cosmos Splint, Yller; MO - Models/ Cosmos Model, Yller) were printed and divided into 12 groups (n = 15) according to the factors: "Postpolymerization" (Ctr - Control; UV - Ultraviolet oven and MW - Microwave); "Printer" (SLA- stereolithography (Forms 2/Formslab); LCD- liquid crystal display (FlashForge Foto 6.0/FlashForge)) and "Aging" (TC - 10,000 thermocycling cycles and Without). Each bar was measured with a digital caliper at 11 points before and after postpolymerization to evaluate dimensional stability. The samples were subjected to the σ test (100Kgf;1 mm/min). Data was evaluated using Three- and Two-way ANOVA, and Tukey's test (5%). Weibull analysis, Scanning Electron Microscopic and optical profilometry was performed.

RESULTS

LCD printing system and UV oven postpolymerization exhibited the highest σ (P < .05). The groups printed in SLA and post-polymerized in microwave ovens showed the greatest variations in their dimensions, for the occlusal splint resin, the OS-SLA-MW group (-4.29 ± 3.15)A showed a shrinkage of 40.2%. The resins for models (3.31 ± 0.66)A and temporary (-2.06 ± 1.52)A showed a shrinkage of 33% and 20.6%, respectively.

CONCLUSIONS

LCD printing with UV light postpolymerization was the most effective method for resins used in occlusal splints, dental models, and temporary restorations. SLA printing with UV postpolymerization showed the most significant dimensional changes, leading to shrinkage in occlusal splint resins, while model resins and temporary restorations expanded.

CLINICAL RELEVANCE

Resins for 3D printing should ideally be post-polymerized with UV light and printed using LCD technology, as this approach results in better mechanical properties and less dimensional change compared to microwave oven post-polymerization.

Is zirconia surface etching a viable alternative to airborne particle abrasion? A systematic review and meta-analysis of in vitro studies

OBJECTIVES

This systematic review aimed to determine the effectiveness of various etching surface treatments on zirconia bond strength with the following research question: "Can zirconia etching serve as a viable alternative to airborne particle abrasion (APA) for achieving reliable bonding?".

DATA

In vitro studies comparing APA, performed with either conventional or silica-coated aluminum oxide (Al2O3) particles, with various etching protocols in terms of bonding performance were included. The risk of bias of the included studies was assessed using the QUIN's tool for in vitro studies. Meta-analyses were performed using RevMan; random-effects models were applied, and heterogeneity was tested using the I2 index. The significance level was set at p < 0.05.

SOURCES

A comprehensive literature search was conducted across electronic databases, including Clarivate Analytics' Web of Science, Cochrane Library, EMBASE, PubMed, Scopus and ProQuest.

STUDY SELECTION

Fifty-four relevant articles were included in this systematic review. According to the QUIN's tool, 7 studies were rated as "high risk of bias", 46 studies were rated as "medium risk", and 1 study was rated as "low risk". Nineteen studies were used for meta-analyses. Mostly, APA demonstrated significantly higher bond strength compared to various etching protocols (p < 0.05). However, no statistical difference was found between APA and high concentrations (40-48 %) of hydrofluoric acid (HF) in terms of immediate- and medium-term bond strength to resin composite (p > 0.05). On enamel, an experimental hot etching solution performed significantly better than APA in short-term follow-up (p < 0.05). A novel multi-acid solution exhibited significantly higher immediate shear bond strength to resin cement than APA (p < 0.05). Variable heterogeneity, ranging from low to high, was observed.

CONCLUSIONS

APA remains the surface treatment with the strongest evidence in the literature and it is usually more efficacious than zirconia etching. However, highly concentrated HF and an experimental hot etching solution have demonstrated similar or significantly higher bond strength values over time compared to APA, depending on the adhesive substrate. A recently introduced multi-acid solution (Zircos-E) needs to be further explored, especially in regards to long-term bond durability.

CLINICAL SIGNIFICANCE

This systematic review provides a comprehensive analysis of the existing in vitro evidence on the potential of zirconia etching and the bond durability of resin-based materials after artificial aging. Selecting appropriate surface treatment protocols is crucial for achieving optimal clinical outcomes.

Matrix metalloproteinases in dentin: Assessing their presence, activity, and inhibitors - a review of current trends

INTRODUCTION

Dentin integrity is a critical aspect of tooth structure, with matrix metalloproteinases (MMPs) playing a crucial role in dentinogenesis, caries formation, and dental bonding. It is crucial to accurately assess MMP activity to understand dentin pathophysiology and develop effective clinical strategies.

OBJECTIVES

The study aimed to conduct a thorough review and comprehensive summary of diverse techniques employed in assessing MMPs in dentin.

DATA AND SOURCES

To conduct the research, electronic databases were systematically searched and manual citation searches were performed. A total of 621 articles were identified. After eliminating duplicates and irrelevant studies, 70 articles were included in the review. 25 articles with overlapping methodologies were also excluded.

STUDY SELECTION

The selection criteria were based on the relevance of the studies to MMPs and MMP inhibitors in dentin without regard to the study design. Only peer-reviewed articles published in English were included. The search was restricted to studies published until November 2022.

CONCLUSION

The comprehensive analysis of various studies has yielded 37 techniques for evaluating MMPs and MMP inhibitors, which hold significant promise in creating diagnostic markers and devising targeted therapeutic interventions.

Influence of silver coated zeolite fillers on the chemical and mechanical properties of 3D-printed polyphenylene sulfone restorations

OBJECTIVES

To investigate the chemical and mechanical properties of polyphenylene sulfone (PPSU) depending on its composition and manufacturing.

METHODS

Unfilled-PPSU1 and with antimicrobial silver coated zeolites filled-PPSU2 specimens were made of granulate-GR, filament-FI, or printed-3D. Scanning microscopy and X-ray spectroscopy were performed. Martens hardness-HM, elastic indentation modulus-EIT and flexural strength-FS were determined initially and after aging. Shear bond strength-SBS to veneering and luting composite after conditioning with 7 adhesive systems were examined after aging. Silver leaching was tested after 1-, 3-, 7-, 14-, 21-, 28- and 42 days. Analyses of variance, Kolmogorov-Smirnov, Kruskal-Wallis, Mann-Whitney U, unpaired t-tests and Weibull modulus were computed (p < 0.05).

RESULTS

Zeolites were homogeneously distributed. PPSU1-GR and PPSU1-FI showed the highest HM/EIT, followed by PPSU2-GR, PPSU1-3D and PPSU2-3D. PPSU2-FI presented the lowest HM/EIT, displaying micro pits. Aging showed reduced HM/EIT in PPSU1 and no impact on PPSU2, while FS increased (PPSU1) or decreased (PPSU2). PPSU2-3D presented lower FS than PPSU1-3D. High SBS to the luting (7.0-16.2 MPa) and veneering composite (11.8-22.2 MPa), except for adhesive system PR, were observed. PPSU2-3D showed the highest silver release (9.6%), with all compositions dispensing silver over 42 days.

CONCLUSIONS

For the examined period of 6 weeks, antimicrobial silver ions were released from filled PPSU. The high SBS between PPSU and veneering/luting composite confirmed the feasibility of esthetically veneering and luting filled PPSU. To achieve mechanical properties like unfilled PPSU, the processing parameters of filled PPSU require refinement.

CLINICAL SIGNIFICANCE

This investigation provides proof of principle that PPSU can be successfully doped with silver-coated zeolites. The combination of 3D-printing with an antimicrobial thermoplastic constitutes a great opportunity in the field of prosthetic dentistry. Potential applications include clasps for removable dental prostheses, provisional or permanent fixed dental prostheses and implant abutments.

Comparative Strength Study of Indirect Permanent Restorations: 3D-Printed, Milled, and Conventional Dental Composites

Background/Objectives: Limited research has been performed to assess the strength of resin-bonded 3D-printed restorations. Based on that, this study investigates the impact of different manufacturing methods on the fracture load of indirect composite restorations (ICRs) following an aging process. Methods: Three manufacturing techniques-conventional (CRC), milled (MRC), and printed (PRC)-were evaluated using 60 specimens, each with a diameter of 10 mm and a thickness of 1.0 mm. Sandblasting with Al2O3 particles was employed to optimize the bonding process, significantly influencing surface roughness parameters (Ra, Rz, RSm). All specimens were bonded to the dentin analog using composite resin cement and subjected to either 10,000 thermocycles (TC) or storage (ST) at 37 °C in distilled water. Fracture load assessments were performed using a universal testing machine. A finite element analysis was conducted to assess stress distribution. Results: Two-way ANOVA results indicated that the manufacturing method significantly affected mean fracture load values (p < 0.001), with PRC showing the highest mean fracture load (4185 ± 914 N), followed by MRC (2495 ± 941 N) and CRC (599 ± 292 N). The aging protocol did not have a significant impact on fracture load. Conclusions: This study revealed that 3D-printed resin composite exhibited comparable strength to milled resin composite when adhesively cemented, suggesting it is a promising option for indirect composite restorations based on its mechanical performance. However, further research is needed to evaluate its bond strength and optimal surface treatment methods to prevent early debonding.

Effects of minimally invasive endodontic access cavity in molar teeth on polymerization, porosity and fracture resistance

Minimally invasive access cavities have been proposed in the last decade to reduce tooth tissue loss during endodontic treatment and mitigate compromised fracture resistance of endodontically treated teeth. Fracture resistance of molars with different types of access cavity design may be affected by restorative materials and aging. Insufficient literature data exist on the effect of cavity design and type of restorative materials on restorative aspects such as material adaptation or photo-polymerization in restricted access cavities. This study analyses quality of polymerization, material adaptation and fracture resistance of molars with different types of access cavities restored with glass-ionomer, high-viscosity fiber-reinforced bulk-fill and nanofilled resin composite. Plastic molar teeth with truss (TREC) and traditional endodontic access cavity (TEC) were restored with nanofilled composite (Filtek Supreme), glass-ionomer Fuji IX and Filtek or fiber-reinforced everX Posterior and Filtek. Porosity was determined using microcomputer tomography and the degree of conversion of resin-based materals using micro-Raman spectroscopy. Human molars prepared and restored in the same way were used for fracture resistance testing at baseline and after thermocycling. The results demonstrate that high-viscosity fiber-reinforced composite was difficult to adapt in TREC cavity leading to greater porosity than Filtek or Fuji. TREC design did not affect composite polymerization and led to higher fracture resistance of restored molars compared to TEC but also more unrestorable fractures.

Fracture resistance of CAD/CAM tooth-colored versus cast metal post-and-core restorations in root filled teeth: An in vitro study

Purpose

This study investigated the fracture resistance and failure modes of custom-fabricated post- and core dental restorations using various CAD/CAM materials.

Materials and Methods

Seventy-five mandibular second premolars were allocated to five groups (n = 15) and prepared for standardized post and core restorations. The groups included a control group comprising cast metal and four CAD/CAM materials: Vita Enamic, Shofu HC, Trilor, and PEKK. Fracture resistance was assessed using a compressive force at a crosshead speed of 1 mm/min until failure occurred. Data were analyzed using one-way analysis of variance (ANOVA) and chi-square tests.

Results

The metal group had the highest fracture resistance (244.41 ± 75.20 N), with a significant variance compared to that in the CAD/CAM groups (p < 0.001). No significant differences were observed among the non-metallic groups.

Conclusions

While several CAD/CAM materials displayed satisfactory flexural properties, cast metal posts showed superior fracture resistance in endodontically treated teeth but were mostly associated with catastrophic failure. The clinical application of CAD/CAM materials for post-core restorations presents a viable alternative to traditional metal posts, potentially reducing the risk of unfavorable fractures.

Effect of Surface Treatment with Zirconium Dioxide Slurry on the Bond Strength of Resin Cement to Ultratranslucent Zirconia

This laboratory study aimed to evaluate the effects of zirconium dioxide (ZrO2) slurry surface treatment on the bond strength of ultratranslucent zirconia to resin cement using different ceramic primers. The surface morphology was evaluated by scanning electron microscopy (SEM) and atomic force microscopy (AFM), and the interface was evaluated by SEM. Additionally, the phase composition was analyzed by X-ray diffraction (XRD). Specimens of zirconia (n=120) were obtained and divided into two groups according to the surface treatment: (1) airborne particle abrasion with 50-μm aluminum oxide (n=60) and (2) ZrO2 slurry (n=60). The 60 specimens were then further divided into three groups (n=20) according to the ceramic primer application: no primer (NP), Monobond N (MB), and Clearfil ceramic primer (CP). Four resin cement cylinders were built on each ceramic specimen. Half of the specimens (n=10) were subjected to a microshear bond strength (μSBS) test after 24 hours of storage in distilled water, and the other half (n=10) were subjected to a μSBS test after thermocycling. Additional specimens were prepared for SEM, AFM, and XRD analyses. According to the Kruskal-Wallis and Student-Newman-Keuls post hoc tests, the μSBS values were significantly higher for MB and CP than for NP (p<0.05), and there were no significant differences in μSBS for both surface treatments associated with MB and CP after 24 hours of storage (p>0.05). Thermocycling significantly decreased the μSBS values for all specimens, especially for the NP groups and ZrO2 slurry treatment groups, and gaps at the interface were observed by SEM. SEM and AFM analyses showed agglomerate-type irregularities on the ceramic surface for ZrO2 slurry treatment. XRD spectra showed that ZrO2 slurry did not cause phase transformation. It was concluded that ZrO2 slurry promoted irregularities on the ultratranslucent zirconia surface, not causing phase transformation; moreover, the values of μSBS were comparable to those of airborne particle abrasion with aluminum oxide. However, neither surface treatment nor ceramic primer prevented the degradation of the interface.

Mechanical properties of 3D-printed resin denture teeth: An in vitro study

PURPOSE

The purpose of this study was to compare the wear, fracture strength, and mode of failure of various brands of 3D-printed resin denture teeth with prefabricated acrylic resin. Additionally, the study aimed to analyze the different modes of failure exhibited by these teeth.

MATERIALS AND METHODS

The study utilized 90 3D-printed and 30 prefabricated, 3D-printed resin teeth from three brands: L = Optiprint Lumina, A = ASIGA DentaTooth, P = Power resins, along with prefabricated acrylic teeth from M = Major Super Lux. Each of the 30 samples per main group was divided into two subgroups: The first subgroup samples (M1, A1, L1, P1) were subjected to thermal cycling and mechanical loading; M2, A2, L2, and P2 were not aged and tested directly. A scan of a prefabricated acrylic tooth was taken using an intraoral scanner, and then the STL file was printed using an Asiga 3Dprinter. The specimens underwent aging to simulate 5 years of clinical use with 10,000 thermal cycles and 1,200,000 dynamic load cycles on a chewing simulator. Surface roughness parameters (Rz, Ra, Rq) were measured using a 3D Optical Profilometer, fracture resistance was assessed using a universal testing machine, and SEM analysis was performed to observe failure modes. Statistical analysis using T-test, one-way analysis, and two-way analysis processed by the Statistical Package for Social Sciences (SPSS) software version 23.0 (SPSS: Inc., Chicago, IL, USA) was done with a level of significance set at <0.05.

RESULTS

The results showed that the difference in surface roughness parameters (Rz, Ra, Rq) before and after aging for Group M, Group A, Group L, and Group P was statistically significant (p < 0.05). Two-way ANOVA for wear resistance between aging and groups on dependent variable Rz (p = 0.002), Ra (p = 0.001), Rq (p = 0.001) were significant. Multiple comparisons for surface roughness parameters showed Group A and Group L were lower than Group P and Group M (p < 0.05). For fracture strength, One-way ANOVA showed a significant difference between groups for fracture strength either without or after the aging procedure (p < 0.05). Multiple comparisons for fracture strength without aging showed no significant difference between Group M, Group A, and Group L (p > 0.05). After the aging procedure fracture strength for Group M was higher than Group A, Group L, and Group P (p < 0.05).

CONCLUSION

3D-printed resin teeth showed a greater and comparable wear resistance to prefabricated acrylic teeth. Fracture strength was comparable between prefabricated acrylic teeth and 3D-printed resin (Asiga and Lumina) before aging, but after aging 3D-printed resin teeth showed less fracture strength.

Prevention of secondary caries using fluoride-loaded chitosan nanoparticle-modified glass-ionomer cement

OBJECTIVE

To study the effect of incorporating chitosan and fluoride-loaded chitosan nanoparticles into a glass-ionomer cement (GIC) to prevent secondary caries.

MATERIALS AND METHODS

A standard cervical cavity (mesio-distal width 6 mm, cervico-occlusal width 2 mm, and depth 2 mm) was prepared on 30 molars for the following restoration groups: group 1, conventional GIC restoration; group 2, chitosan (10%) modified GIC restoration; group 3, fluoride loaded chitosan nanoparticles (10%) modified GIC restoration. The restored teeth were subjected to 1,500 thermal cycles before undergoing a multi-species cariogenic biofilm challenge. The restored teeth were examined by micro-computed tomography (micro-CT), scanning electron microscopy with energy dispersive X-ray spectroscopy (SEM/EDX). Data were analyzed by the one-way ANOVA, Tukey HDS, Kruskal Wallis, and Dunn's test.

RESULTS

Micro-CT determined outer lesion depths for groups 1-3 were: 614 ± 20 μm, 589 ± 17 μm, and 560 ± 19 μm respectively. Both modifications with chitosan and fluoride-loaded chitosan nanoparticles significantly affected outer lesion depth (p < 0.05). The modification with fluoride-loaded chitosan nanoparticles statistically significantly decreased the outer lesion depth compared to all other groups (p < 0.05). SEM/EDX showed an increase of calcium, phosphorus, and fluoride at the root dentine adjacent to the restoration in groups 2 and 3 (modified GIC). This increase was statistically significantly higher in the group modified with fluorine-loaded nano chitosan particles compared to the other groups (p < 0.05).

CONCLUSION

Incorporation of 10% chitosan and 10% fluoride-loaded chitosan nanoparticles into GIC restorative material can prevent secondary root caries development. 10% fluoride-loaded chitosan nanoparticles were more effective.

CLINICAL SIGNIFICANCE

Glass ionomer cement modified with fluoride-loaded chitosan nanoparticles may be a promising restorative material in pediatric and preventive dentistry due to their controlled release properties.

Influence of the Composition of Provisional Luting Materials on the Bond Strength of Temporary Single-Tooth Crowns on Titanium Abutments

In addition to zinc oxide-based cements, resin-based materials are also available for temporary cementation. The aim of this in vitro study was to determine the influence of the different material compositions on temporary bonds. In nine test series (n = 30), temporary bis-acrylate single-tooth crowns were bonded onto prefabricated titanium abutments with nine different temporary luting materials. After simulating an initial (24 h, distilled water, 37 °C), a short-term (7 days, distilled water, 37 °C) and a long-term provisional restoration period (12h, distilled water, 37 °C; thermocycling: 5000 cycles) in subgroups (n = 10), the bond strength was examined using a combined tensile-shear test. Statistical analysis was performed by univariate analysis of variance or a non-parametric Kruskal-Wallis test, followed by post hoc tests. Of the three resin-based materials, two showed significantly higher bond strength values compared to all other materials (p < 0.001), regardless of the storage procedure. The resin-based materials were followed by eugenol-free and eugenol-containing zinc oxide materials. Significant intragroup differences were observed between the composite-based materials after all storage periods. This was only observed for some of the zinc oxide-based materials. The results show that under in vitro conditions, not only the composition of the temporary luting materials but also the different storage conditions have a significant influence on temporary bonds.

Repair strength of 3D-printed denture base resins: Effect of surface treatment and repair material type

PURPOSE

The aim of the study was to investigate the effect of surface treatment and repair materials on the flexural strength of repaired 3D-printed denture base resins after thermal aging.

MATERIALS AND METHODS

Bar-shape specimens (64 × 10 × 3.3 mm) were designed as intact (control) specimens while repair specimens were printed in sections with 2.5 mm space for repair material. Printing was performed with either ASIGA or NextDent denture base material. In each material, one group received no surface treatment, while other repair groups were subjected to one of three surface treatments: (1) monomer application, (2) aluminium oxide particles-abrasion, or (3) both methods (aluminum oxide particles-abrasion and monomer application). Pairs were fixed in a customized mold then repaired with either autopolymerizing acrylic resin or flowable composite (n = 9). Repaired specimens were incubated for 48 h at 37°C in distilled water and then subjected to thermal cycling (5000 cycles). A 3-point bending test was used to evaluate the flexural strength using a universal testing machine, and mode of failure determined followed by fractured surface analysis using scanning electron microscope. Data were analyzed using ANOVA and post hoc Tukey test (α = 0.05).

RESULTS

Both resin materials showed a significant decrease in the flexural strength of repaired specimens when compared to control ones (p < 0.001). Groups with no surface treatment had significantly lower flexural strength than those with surface treatment (p < 0.001). Groups treated with monomer application, and with aluminum oxide particles abrasion plus monomer application had similar flexural strength values (p > 0.05), which were higher than those treated with aluminum oxide particles abrasion alone (p < 0.001). Specimens repaired with composite resin showed higher flexural strength than those repaired with auto-polymerized resin (p < 0.05) however, specimens treated with aluminum oxide particles abrasion alone had similar values for both repair materials (p = 0.95). Adhesive failure was dominant in all repaired groups with auto-polymerized while cohesive and mixed were dominant with composite repair groups.

CONCLUSION

Surface treatment improved the repair strength of 3D-printed denture base resins. Using composite resin for repair shows better strength with dominant cohesive and mixed failure suggesting that surface treatment and composite repair are suitable procedures for 3D-printed denture base repair.

Investigating the impact of different cleaning techniques on bond strength between resin cement and zirconia and the resulting physical and chemical surface alterations

PURPOSE

To evaluate the effect of cleaning methods and thermocycling on the micro-tensile bond strength between resin cement and contaminated zirconia and to characterize the physicochemical alterations at the zirconia surface resulting from contaminants and subsequent application of cleaning methods.

MATERIALS AND METHODS

Thirty-two alumina air-abraded zirconia blocks were divided into eight groups: (i) uncontaminated control followed by methacryloyloxydecyl dihydrogen phosphate (MDP) primer (G-Multi Primer) application (CON). In groups ii-viii, the blocks were contaminated with saliva and silicone disclosing agents, followed by cleaning as follows: (ii) MDP primer applied, followed by contamination (GMP1); (iii) MDP primer applied before and after contamination (GMP2); (iv) cleaning with alumina air-abrasion (APA); (v) cleaning with sodium hypochlorite (NaOCl); (vi) cleaning with Ivoclean (IVC); (vii) cleaning with ZirClean (ZC); and (viii) cleaning with Katana Cleaner (KC). After cleaning, the zirconia blocks in groups iv-viii were applied with MDP primer. The blocks in each group were cemented together with resin cement (G-Cem Linkforce). Subsequently, each bonded zirconia block was sectioned using a water-cooled diamond saw into microsticks (1 × 1 × 9 mm3). Micro-tensile bond strength was measured after either 24 h or 10,000 thermal cycles (n = 20/subgroup). Data were analyzed using two-way analysis of variance (ANOVA), followed by one-way ANOVA, and Tukey's post-hoc test. The contact angle measurements, energy dispersive X-ray spectroscopy (EDS), and Fourier-transform infrared (FTIR) spectrometer were used for physiochemical evaluation.

RESULTS

After 24 h of water storage, the highest bond strength was observed in the CON, NaOCl, APA, and GMP2 groups. After thermocycling, the bond strength significantly decreased in all groups except the GMP2 group, which maintained the highest bond strength. Commercial ceramic cleaning agents (IVC, ZC, and KC groups) exhibited lower bond strengths than the CON groups in both aging conditions.

CONCLUSIONS

The application of MDP primer before and after contamination is a promising cleaning protocol for removing saliva and silicone disclosing agent contaminants from zirconia surfaces. This approach achieved the highest bond strength and maintained it even after artificial aging through thermocycling.

Effect of thermocycling on tensile bond strength of autopolymerized, heat-polymerized, milled, and 3D printed denture base materials bonded to 4 different denture liners: an in vitro study

BACKGROUND

Digitally fabricated dentures may require relining due to continual alveolar ridge resorption. However, studies evaluating the tensile bond strength (TBS) of digitally fabricated dentures bonded to denture liners are lacking. This study aimed to evaluate the TBS of autopolymerized, heat-polymerized, milled, and 3D printed denture base materials bonded to 2 acrylic-based and 2 silicone-based denture liners, both before and after thermocycling. Additionally, the impact of thermocycling on the TBS were also evaluated.

METHODS

The TBS of 4 different denture base materials (Palapress (PL), Vertex Rapid Simplified (VR), Smile CAM total prosthesis (SC), and NextDent denture 3D+ (ND)) bonded to 2 acrylic-based (GC Soft-Liner (GC) and Tokuyama Rebase II (RB)) and 2 silicone-based (Ufi Gel P (UP) and Sofreliner Tough M (ST)) denture liners were tested. Specimens (n = 8) were divided into non-thermocycling and thermocycling groups. Non-thermocycling specimens were tested after 24-hours water immersion, while thermocycling specimens were underwent 5000 cycle and were immediately tested. Mode of failure was examined under a stereomicroscope. Data were analyzed using 2-way ANOVA and Tukey HSD tests (α = 0.05), and independent samples t test (α = 0.05) for TBS between non-thermocycling and thermocycling groups.

RESULTS

For the non-thermocycling groups, within the same denture liner material, no significant differences were found between denture base materials, except the ND + RB group, which had significantly lower TBS. For the thermocycling groups, within the same denture liner material, the TBS in the PL group exhibited the highest and the ND group exhibited the lowest. Within the same denture base material, in both non-thermocycling and thermocycling groups, the TBS in the ST group exhibited the highest; in contrast, that in the GC group exhibited the lowest. No significant differences were observed in TBS between non-thermocycling and thermocycling groups, except for denture base materials bonded to the ST group, SC + UP, and ND + UP groups.

CONCLUSIONS

Milled denture base can be relined with acrylic-based or silicone-based denture liner. However, cautions should be exercised when relining 3D printed denture base. Thermocycling did not affect TBS between acrylic-based denture liners and denture bases. In contrast, it affected the bond between silicone-based denture liner and denture base.

Bond Strength of Nanocomposite Hard Liner to CAD-CAM Milled, 3D Printed, and Conventionally Fabricated Denture Base Resins

BACKGROUND

To investigate the effect of zirconium dioxide nanoparticles (ZrO2NPs) on the shear bond strength (SBS) of hard denture lines bonded to different denture base resins.

METHODS

Five different denture bases were used in this study: conventional heat-cured resin, IvoCad, AvaDent, NextDent, and FormLabs, in acrylic specimens of 10 × 10 × 2.5 mm3 (N = 150, n = 10). Specimens were centered at the bottom of a silicon mold to create an auto-polymerized holder. Three major groups of reline material were used: no ZrO2NPs (control), 2 wt.%, and 4 wt.% ZrO2NPs. Reline was bonded to the resin surface using a customized jig. After polymerization, specimens were stored in distilled water, and 5000 thermal cycles were performed. Each specimen was fixed to an Instron machine, and SBS was tested using a blade loaded (1 mm/min) at the resin interface until failure. Data was collected and analyzed using two-way ANOVA and post hoc Tukey test (α = 0.05).

RESULTS

AvaDent showed the highest SBS when compared with other denture base materials (p < 0.001) except for IvoCad. The addition of ZrO2NPs significantly decreased the SBS of AvaDent (p = 0.003) and IvoCad (p = 0.001), while heat polymerized resin, Formlabs, and NextDent showed no significant change in SBS (p > 0.05).

CONCLUSION

CAD-CAM milled denture base resin showed higher SBS with pure denture reline. The addition of ZrO2NPs decreased the SBS of reline with CAD-CAM milled denture base resins but did not change bond strength with 3D printed and conventional denture base resins.

Influence of luting strategies on dentin bond performance of self-adhesive resin luting cement in combination with a universal adhesive

OBJECTIVES

This study aimed to evaluate the dentin bond performance of various resin luting cement (RLC) systems combined with universal adhesives in different luting strategies.

MATERIALS AND METHODS

Three self-adhesive resin luting cements (SRLCs) were used with universal adhesives as primers. Twelve specimens per group were prepared to measure shear bond strength (SBS) under distinct luting strategies in etch-&-rinse and self-etch modes. Regarding luting strategies, the bonded specimens were categorized into four groups based on tooth primer application and the curing mode of the SRLC paste: (i) with light irradiation of the tooth primer (wL) + dual-cure mode (DC) of the SRLC paste, (ii) wL + self-cure mode (SC) of the SRLC paste, (iii) without light irradiation of the tooth primer (woL) + DC mode of the SRLC paste, and (iv) woL + SC mode of the SRLC paste. Specimens were also subjected to different storage conditions: 24 h in water (baseline condition) and 10,000 cycles of thermal cycling.

RESULTS

Luting strategy, storage condition, and SRLC system type significantly influenced dentin SBS values in both etching modes. Notably, certain SRLCs exhibited significantly higher dentin SBS when the primer was light-irradiated compared with no primer irradiation.

CONCLUSION

Most SRLCs demonstrated higher dentin bond strength with light-irradiated primers, suggesting potential enhancement of dentin bond performance via primer light irradiation.

Long-Term Bonding Performance of One-Bottle vs. Two-Bottle Bonding Agents to Lithium Disilicate Ceramics

The aim of this study was to compare the long-term bonding performance to lithium disilicate (LDS) ceramic between one-bottle and two-bottle bonding agents. Bonding performance was investigated under these LDS pretreatment conditions: with hydrofluoric acid (HF) only, without HF, with a two-bottle bonding agent (Tokuyama Universal Bond II) only. Shear bond strengths between LDS and nine resin cements (both self-adhesive and conventional adhesive types) were measured at three time periods: after one-day water storage (Base), and after 5000 and 20,000 thermocycles (TC 5k and TC 20k respectively). Difference in degradation between one- and two-bottle bonding agents containing the silane coupling agent was compared by high-performance liquid chromatography. With HF pretreatment, bond strengths were not significantly different among the three time periods for each resin cement. Without HF, ESTECEM II and Super-Bond Universal showed significantly higher values than others at TC 5k and TC 20k when treated with the recommended bonding agents, especially at TC 20k. Difference in degradation between one- and two-bottle bonding agents containing the silane coupling agent was compared by high-performance liquid chromatography (HPLC). For both cements, these values at TC 20k were also not significantly different from pretreatment with only Tokuyama Universal Bond II. For LDS, long-term bond durability could be maintained by pretreatment with Tokuyama Universal Bond II instead of the hazardous HF.

Validation of clinically related aging models based on enamel wear

PURPOSE

Physiological and erosive wear reported in clinical studies were reviewed, and in vitro aging models were developed to simulate and compare the effect of aging on human teeth with the review data obtained from clinical studies.

METHODS

A review of clinical studies and randomized clinical trials that quantify enamel wear was performed in the PubMed database. The first in vitro analysis evaluated the effect of mechanical chewing simulation only. Enamel specimens were aged in the chewing simulator (up to 1.2 million cycles) with two occlusal loads (30 and 50 N). In the second in vitro analysis, specimens were aged in two aging models. The first model (MT) simulated mechanical and thermal oral challenges: MT1- 240,000 chewing and 10,000 thermal cycles, MT2- 480,000 chewing and 20,000 thermal cycles, MT3- 1.2 million chewing and 50,000 thermal cycles. The second model (MTA) simulated mechanical, thermal, and acidic oral challenges as follows: MTA1- 240,000 chewing, 10,000 thermal and 3-h acidic cycles; MTA2: 480,000 chewing, 20,000 thermal and 6-h acidic cycles, MTA3- 1.2 million chewing, 50,000 thermal and 15-h acidic cycles.

RESULTS

The review included 13 clinical studies evaluating tooth wear (eight physiological and five erosive). The results estimated the annual average physiological wear as 38.4 µm (9.37-51). In comparison, the MT1 showed wear of 60 (24) µm. Also, the average annual erosive wear in the literature was 179.5 µm (70-265) compared to MTA1-induced wear of 209 (14) µm.

CONCLUSION

There was wide variation in tooth wear reported in clinical studies, suggesting a critical need for more accurate studies, possibly based on scanning technologies. Despite this, the data reported using the novel aging models are within a range to be considered consistent with and to simulate tooth wear measured in vivo.

Investigation of Absorbable and Non-Absorbable Multifilament Suture Materials in Terms of Strength Changes Using Chlorhexidine Mouthwash and Thermal Cycling: An In Vitro Study

Sutures are natural or synthetic biomaterials utilized to hold tissues together. Following oral surgery, the surgical site and sutures are physically affected by many different factors. This study was conducted to evaluate the effect of artificial saliva (AS) and chlorhexidine mouthwash on the tensile strength of absorbable multifilament PGLA (polyglycolide-co-l-lactide) and non-absorbable multifilament silk sutures. PGLA and silk sutures, which are commonly used in oral surgery, were used to evaluate the change in strength of the sutures. A total of 352 suture samples were divided into eight equal groups (n = 44) and used for the experiments. Tensile strength was tested on days 0, 3, 7, and 14. For the silk sutures, there was a significant decrease in tensile strength in all groups at time T3 compared to T0, T1, and T2, and at times T1 and T2 compared to T0. For PGLA sutures, there was a significant decrease in all groups at time T3 compared to T0, T1, and T2. This study shows that chlorhexidine mouthwash significantly reduces suture resistance for 14 days after surgery.

Degree of conversion and interfacial adaptation of touch-cure resin cement polymerized by self-curing or dual-curing with reduced light

OBJECTIVES

The first aim of this study was to determine whether there is a difference in degree of conversion (DC) of touch-cure cements polymerized by self-curing with adhesive or dual-curing under reduced light. The second aim was to compare interfacial adaptation of zirconia restoration cemented using touch-cure cements self-cured or dual-cured by reduced light.

METHODS

The DC of touch-cure resin cements with adhesive was measured continuously using Fourier transform infrared spectrometry. Experimental groups differed depending on touch-cure cement. Each group had three subgroups of polymerization method. For subgroup 1, the DC was measured by self-curing. For subgroups 2 and 3, the DCs were measured by dual-curing with reduced light penetrating 3 mm and 1 mm zirconia blocks, respectively. For interfacial adaptation evaluation, Class I cavity was prepared on an extracted third molar, and zirconia restoration was fabricated. The restoration was cemented using the same cement. Groups and subgroups for interfacial adaptation were the same as those of the DC measurement. After thermo-cycling, interfacial adaptation at the tooth-restoration interface was evaluated using swept-source optical coherence tomography imaging.

RESULTS

The DC of touch-cure cement differed depending on the measurement time, resin cement, and polymerization method (p < 0.05). Interfacial adaptation was different depending on the resin cement and polymerization method (p < 0.05).

CONCLUSION

For touch-cure cement, light-curing with higher irradiance presented a higher DC and superior interfacial adaptation than light-curing with lower irradiance or self-curing.

CLINICAL RELEVANCE

Although some adhesives accelerate the self-curing of touch-cure cement, light-curing for touch-cure cement is necessary for zirconia cementation.

Influence of sandblasting and bonding on the shear bond strength between differently pigmented polyetheretherketone (PEEK) and veneering composite after artificial aging

OBJECTIVE

Achieving a strong bond between Polyetheretherketone (PEEK) and veneering composites is challenging due to PEEKs low surface energy. This study examined the effects of sandblasting and bonding on the shear bond strength (SBS) between veneering composite and pigmented PEEK, considering artificial aging.

METHODS

Of three pigmented PEEK compounds (DC4420R, DC4450R, DC4470R; Evonic Operations GmbH, Marl, Germany), 40 specimens each were milled and polished up to 2500 grit. Prior to veneering, specimens were divided into 4 subgroups: Subgroup 1: Polishing; 2: Polishing + bonding; 3: Sandblasting; 4: Sandblasting + bonding. Sandblasting was performed using Al2O3. Adhesive was an agent containing MMA (Signum Universal Bond, Kulzer GmbH, Hanau, Germany). After veneering (Composite, Kulzer GmbH) the subgroups were divided into 2 subgroups. One subgroup was immersed in 37 °C warm distilled water for 24 h. The second subgroup was artificially aged by thermocycling (TCL) with 5000 cycles in distilled water (5 °C / 55 °C; 30 s). Surface roughness, water contact angles and failure modes were recorded. SBS was measured using a universal testing machine.

RESULTS

Results demonstrated that the combination of sandblasting and bonding significantly improved the SBS compared to polishing alone. PEEK color did not significantly influence the SBS. Aging by TCL had a negative effect on the SBS.

SIGNIFICANCE

Sandblasting and the use of an adhesive containing MMA were found to be effective in achieving satisfactory SBS between veneering composite and pigmented PEEK surfaces. These pretreatment methods demonstrate their potential for establishing durable and reliable bonding in clinical applications.

The influence of hygroscopic expansion of resin supporting dies on the fracture resistance of ceramic restorations during thermal cycling

OBJECTIVES

To evaluate the hygroscopic expansion characterization of resin composite dies during thermal cycling, and their influence on the fracture resistance of dental ceramic materials as well as the effect of pre-immersion on these measurements.

METHODS

Disc-shaped specimens (φ = 15.0 mm, h = 1.2 mm) and anatomical crown dies of four resin composites (epoxy, Z350, P60, G10) were fabricated. Disc-shaped samples were continuously soaked in distilled water and the volume expansion was measured at different time point by Archimedes method. Disc-shaped samples were pre-immersed for 0, 7, or 30 days, elastic modulus and hardness were measured using Nanoindentation test; thermal cycling (TC) test was performed (5 °C-55 °C, 104 cycles), and volume expansion during TC was measured. Four kinds of resin die with pre-immersion for 0, 7, or 30 days were cemented to 5Y-Z crown, or epoxy dies without pre-immersion were cemented to 5Y-Z, 3Y-Z and lithium disilicate glass (LDG) crowns, and load-to-failure testing was performed before and after TC. Finite element analysis (FEA) and fractography analysis were also conducted.

RESULTS

The hygroscopic expansion was in the order: epoxy > Z350 > P60 > G10. Except for G10, the other three resin composites exhibited different degrees of hygroscopic expansion during TC. Only the elastic modulus and hardness of epoxy decreased after water storage. However, only the fracture loads of 5Y-Z and LDG crowns supported by epoxy dies were significantly decreased after TC. FEA showed a stress concentration at the cervical region of the crown after volume expansion of the die, leading to the increase of the peak stress at the crown during loading.

SIGNIFICANCE

Only the hygroscopic expansion of epoxy dies caused by TC led to the decrease in the fracture resistance of the 5Y-Z and LDG crown, which may be related to the decrease in the elastic modulus of the epoxy die and the tensile stress caused by it.

An in vitro evaluation of bond strength and failure behavior between 3D-printed cobalt-chromium alloy and different types of denture base resins

OBJECTIVES

This study aimed to evaluate the shear bond strength and failure behavior between cobalt-chromium (Co-Cr) alloy and different types of denture base resins (DBRs) over time.

METHODS

Seventy-two disk-shaped specimens (8 mm in diameter and 2 mm in thickness) were manufactured using a selective laser melting technology-based metal 3D printer. Three types of DBRs were used: heat-cure (HEA group), cold-cure (COL group), and 3D-printable (TDP group) DBRs (n = 12 per group). Each DBR specimen was fabricated as a 5 mm × 5 mm × 5 mm cube model. The specimens of the TDP group were manufactured using a digital light processing technology-based 3D printer. Half of the DBRs were stored in distilled water at 37 °C for 24 h, whereas the remaining half underwent thermocycling for 10,000 cycles. Shear bond strength was measured using a universal testing machine; failure modes were observed, and metal surfaces were evaluated using energy dispersive spectrometry.

RESULTS

The shear bond strength did not differ between the DBR types within the non-thermocycled groups. Contrarily, the TDP group exhibited inferior strength compared to the HEA group (P = 0.008) after thermocycling. All three types of DBRs exhibited a significant decrease in the shear bond strength and an increased tendency toward adhesive failure after thermocycling.

CONCLUSIONS

The bond strength between 3D-printable DBRs and Co-Cr alloy was comparable to that of heat-and cold-cure DBRs before thermocycling. However, it exhibited a considerable weakening in comparison to heat-cure DBRs after simulated short-term use.

CLINICAL SIGNIFICANCE

The application of 3D-printable DBR in metal framework-incorporated removable partial dentures may be feasible during the early phase of the treatment. However, its application is currently limited because the bond strength between the 3D-printable DBR and metal may weaken after short-term use. Further studies on methods to increase the bond strength between these heterogeneous materials are required.

Comparative Evaluation of Two Different Preparation Designs and Materials on the Fracture Resistance of Laminate Veneers: An In Vitro Study

Introduction Laminate veneers are thin porcelain or composite resin shells bonded to the front of teeth for cosmetic enhancement. The design of the tooth preparation is crucial; it involves minimal enamel removal to ensure a proper fit and strong bond. This careful preparation increases the veneers' fracture resistance by preserving tooth structure and evenly distributing stress, ensuring durability and natural appearance. Aim Our aim was to determine the fracture resistance of two preparation designs with two different materials for the fabrication of laminate veneers. Materials and methods An in vitro study was conducted on 40 laminate veneers divided into two groups based on the material used: Group 1 (Cerec Tessera (Dentsply Sirona, Charlotte, NC, USA)) and Group 2 (Upcera, Shenzhen, China). Each group was further divided into two sub-groups based on tooth preparation designs: butt joint and feather edge. The fracture resistance of these veneers following thermocycling was determined, and the mode of fracture was evaluated using a stereomicroscope. Results Feather edge preparation with Cerec Tessera laminate veneer restoration demonstrated the highest fracture resistance at 111.5 N, followed by butt joint preparation with Cerec Tessera laminate veneer restoration, which showed a fracture resistance of 90.8 N. The study identified laminate fractures as the most common type of fracture observed in the veneer restorations, followed by cement interface fractures. Conclusion The study suggests that the feather edge preparation design contributed to higher fracture resistance compared to the butt joint design. This finding aligns with the idea that modifying the preparation design can have a significant impact on the overall strength and durability of veneer restorations. The use of Cerec Tessera, especially in combination with the feather edge design, yielded the maximum fracture resistance.

Effect of Coffee Thermocycling on Color Stability and Translucency of CAD-CAM Polychromatic High Translucent Zirconia Compared With Lithium Disilicate Glass Ceramic

AIMS AND OBJECTIVES

To evaluate the effect of coffee thermocycling on color stability and translucency of CAD-CAM polychromatic high translucent zirconia compared with lithium disilicate glass ceramic.

METHODS

Sixteen rectangular plates (14 × 16 × 1.0 mm) of two ceramic materials (IPS E.max CAD (IEC), IPS E.max ZirCAD Prime [IZP]) were prepared. Each specimen was measured for color coordinates using a spectrophotometer following 30,000 cycles of coffee thermocycling. CIELAB formula was used to determine color and translucency differences (ΔE and ΔTP). The means of ΔE and ΔTP were compared using independent samples t-test and were evaluated using their respective 50%:50% perceptibility and acceptability thresholds (PT and AT). One-way analysis of variance was performed to evaluate the translucency parameter (TP) and surface roughness (Ra) of each material.

RESULTS

Mean ΔE values of IEC (4.69) and IZP (4.64) were higher than the AT (ΔE ≤ 2.7) with no significant difference found between the two groups (p = 0.202). Considering the TP, only IEC showed a statistically significant increase in TP value (p < 0.001). However, the mean ΔTP of IEC (3.25) remained within the range of acceptability (1.3 < ΔTP ≤ 4.4).

CONCLUSIONS

Within the limitations of this current study, the color stability of all materials was clinically affected by coffee thermocycling. In terms of translucency, only lithium disilicate glass ceramic was influenced by coffee thermocycling. High translucent zirconia had superior translucency stability compared to lithium disilicate glass ceramic.

The effect of surface treatment and thermal aging on the bonding of clear aligner attachments to provisional resin-based material: shear bond strength analysis

Objectives

The aim of this study is to evaluate the effect of different surface treatments on the shear bond strength (SBS) of clear aligner attachments bonded to Bis-acryl provisional crowns.

Methods

120 cylindrical bisacrylic composite material (ProTemp type) specimens were prepared and divided into six groups (n = 20) based on surface treatment, control: (no treatment); super coarse grit diamond bur, carbide bur, alumina-blasting, non-thermal plasma treatment, and Er:YAG laser treatment. The features of treated surfaces were examined using scanning electron microscopy (SEM). A flowable composite resin (Transbond XT; 3M Unitek) was bonded to the specimens forming the attachment. Half of specimens were subjected to thermal cycling (5,000 cycles). SBS was measured before and after thermal cycling. Each specimen was loaded at the attachment/resin interface at a speed of 0.5 mm/min until failure. The nature of the failure was analyzed using the composite remnants index (CRI). Two-way ANOVA and Tukey HSD were used for data analysis α =  0.5. For CRI scores analysis, Kruskal-Wallis test and Dunn's multiple comparison were used as post-hoc test.

Results

SEM analysis showed that all surface treatments altered surface properties and increase surface bonding area. The specimens treated with plasma, Er:YAG laser, and alumina-blasting had higher SBS values before and after thermal cycling. In comparison to control plasma, Er:YAG laser, and alumina-blasting showed a significant increase in SBS (P < 0.001) while carbide and diamond bur groups showed no significant differences (P > 0.05). Thermal cycling significantly decreased the SBS of control, carbide bur, diamond bur, and Er:YAG laser while no significant effect of alumina-blasting and plasma group. Er:YAG laser and plasma groups significantly exhibited more dominance for scores 2 and score 3 and the absence of score 0.

Conclusion

Alumina-blasting, Er:YAG laser, or non-thermal plasma surface treatments increased the shear bond strength between clear aligner attachments and resin-based restorations.

Comparative Evaluation of Mechanical Properties and Color Stability of Dental Resin Composites for Chairside Provisional Restorations

Resin composites have become the preferred choice for chairside provisional dental restorations. However, these materials may undergo discoloration, changes in surface roughness, and mechanical properties with aging in the oral cavity, compromising the aesthetics, functionality, and success of dental restorations. To investigate the color and mechanical stability of chairside provisional composite resins, this study evaluated the optical, surface, and mechanical properties of four temporary restoration resin materials before and after aging, stimulated by thermal cycling in double-distilled water. Measurements, including CIE LAB color analysis, three-point bending test, nanoindentation, scanning electron microscopy (SEM), and atomic force microscopy (AFM), were conducted (n = 15). Results showed significant differences among the materials in terms of optical, surface, and mechanical properties. Revotek LC (urethane dimethacrylate) demonstrated excellent color stability (ΔE00 = 0.53-Black/0.32-White), while Artificial Teeth Resin (polymethyl methacrylate) exhibited increased mechanical strength with aging (p < 0.05, FS = 68.40 MPa-non aging/87.21 MPa-aging). Structur 2 SC (Bis-acrylic) and Luxatemp automix plus (methyl methacrylate bis-acrylate) demonstrated moderate stability in optical and mechanical properties (Structur 2 SC: ΔE00 = 1.97-Black/1.38-White FS = 63.20 MPa-non aging/50.07 MPa-aging) (Luxatemp automix plus: ΔE00 = 2.49-Black/1.77-White FS = 87.72 MPa-non aging/83.93 MPa-aging). These results provide important practical guidance for clinical practitioners, as well as significant theoretical and experimental bases for the selection of restorative composite resins.

Influence of endodontic access cavity design on mechanical properties of a first mandibular premolar tooth: a finite element analysis study

OBJECTIVES

This study aimed to investigate the influence of access cavity designs on the mechanical properties of a single-rooted mandibular first premolar tooth under various static loads using a finite element analysis.

MATERIALS AND METHODS

3-dimensional FEA designs were modeled according to the access cavity designs: an intact tooth (control), traditional access cavity (TEC-I), traditional access cavity with Class-II mesio-occlusal cavity design (TEC-II), conservative access cavity (CEC), ninja access cavity (NEC), caries-driven access cavity (Cd-EC), buccal access cavity (BEC) and bucco-occlusal access cavity (BOEC). After the simulated access cavity preparations, root canal treatment was simulated and three different static loads which mimicked oblique and vertical mastication forces were applied to the models. The stress distribution and maximum Von Misses stress values were recorded. The maximum stress values were obtained on both enamel and dentin under multi-point vertical loads.

RESULTS

The maximum stress values were obtained on both enamel and dentin under multi-point vertical loads. Under all load types, the minimum stress distribution was observed in the control group, followed by CEC, NEC and BEC designs. The highest stress concentration was detected in Cd-EC and TEC-II designs. Under single-point vertical loading, the stress was mostly concentrated in the lingual PCD area, while under multi-point vertical loading, the entire root surface was stress-loaded except for the lingual apical third of the root.

CONCLUSION

Preserving tooth tissue by simulating CEC, NEC and BEC access cavities increased the load capacity of a single-rooted mandibular first premolar following simulated endodontic treatment.

Comparative evaluation of bond strength and color stability of polyetheretherketone and zirconia layered with indirect composite before and after thermocycling: An in vitro study

AIM

This study investigates the interaction of zirconia and polyetheretherketone (PEEK) with indirect composite in fixed dental prostheses. This investigation aimed to assess the shear bond strength (SBS) and color stability of zirconia and PEEK before and after aging, addressing critical concerns in dental restorative applications.

SETTINGS AND DESIGN

The current in vitro study used 96 samples, 48 of which were divided into two groups, zirconia and PEEK, before and after thermocycling. A dual-axis chewing simulator was used for thermocycling. SBS was measured using a universal testing machine, and color stability was checked using a reflective spectrophotometer.

MATERIALS AND METHODS

Ninety-six samples were categorized into zirconia and PEEK groups, each with subgroups undergoing thermocycling. Samples were prepared using computer-aided design/computer-aided manufacturing milling and veneered with composite resin. Thermocycling involved 10,000 cycles, simulating stress levels equivalent to approximately 1 year of clinical use. SBS was assessed using standardized tests. Stereomicroscopic analysis was performed to evaluate the type of failure. Color stability of the core materials with indirect composite was done using a spectrophotometer before and after aging.

STATISTICAL ANALYSIS USED

Statistical analysis included paired t-tests and independent t-tests in SPSS software.

RESULTS

The results revealed that SBS values for composite on PEEK decreased from 13.86 ± 0.164 MPa before thermocycling to 13.46 ± 0.185 MPa after thermocycling, with a significant difference (P < 0.005). However, both pre- and postthermocycling values for PEEK were higher than zirconia. The t-test confirmed the lower bond strength of composite to zirconia, with a noteworthy improvement after aging. Stereomicroscopic images revealed adhesive failure for the zirconia group and mixed (adhesive and cohesive) failure for the PEEK group. ΔE values were 3.21 ± 0.127 and 2.93 ± 0.142 for zirconia and PEEK groups, respectively (P < 0.005).

CONCLUSION

Within the limitations of this study, it can be deduced that PEEK is a feasible substitute for zirconia when used in conjunction with indirect composite for the fabrication of dental prostheses.

An In Vitro Study of Retention and Marginal Adaptation of Endocrowns With Different Intracoronal Depths

BACKGROUND

Marginal adaptation and retention of endocrowns are crucial for the success and survival of endocrowns. This study aimed to investigate the effect of different materials and intracoronal depth on the retention and marginal adaptation of CAD/CAM fabricated all-ceramic endocrowns.

METHODS

Thirty-six mandibular premolar teeth with an average surface area of 64.49 mm2 were prepared to receive CAM/CAM fabricated endocrowns. Samples were divided randomly and equally into groups of lithium disilicate with 2 mm intracoronal depth (LD2), lithium disilicate with 4 mm intracoronal depth (LD4), polymer infiltrated ceramic network with 2 mm intracoronal depth (PICN2) and polymer infiltrated ceramic network with 4 mm intracoronal depth (PICN4). All endocrowns were cemented using ParaCore resin cement with 14N pressure and cured for 20 seconds. Fifty measurements of absolute marginal discrepancy (AMD) were done using a stereomicroscope after cementation. After 24 hours, all samples were subjected to thermocycling before the retention test. This involved using a universal testing machine with a crosshead speed of 0.5 mm/min and applying a load of 500N. The maximum force to detach the crown was recorded in newtons and the mode of failure was identified.

RESULTS

Two-way ANOVA revealed that the AMD for PICN was statistically significantly better than lithium disilicate (p=0.01). No statistically significant difference was detected in the AMD between the two intracoronal depths (p=0.72). PICN and endocrowns with 4 mm intracoronal depth had statistically significant better retention (p<0.05). 72.22% of the sample suffered from cohesive failures and 10 LD endocrowns suffered adhesive failures.

CONCLUSIONS

Within the limitations of this study, we found that different materials and intracoronal depths can indeed influence the retention of CAD/CAM fabricated endocrowns. Based on the controlled setting findings, PICN was found to have better retention and better marginal adaptation than similar lithium disilicate premolar endocrowns.

Surface roughness and stainability of CAD-CAM denture base materials after simulated brushing and coffee thermocycling

STATEMENT OF PROBLEM

Denture bases machined from prepolymerized materials have become popular. However, information on the effect of simulated brushing and coffee thermocycling (CTC) on their surface roughness and stainability is lacking.

PURPOSE

The purpose of this in vitro study was to compare the effect of simulated brushing and CTC on the surface roughness (Ra) and stainability of computer-aided design and computer-aided manufacturing (CAD-CAM) denture base materials and a heat-polymerized denture base material.

MATERIAL AND METHODS

Forty disk-shaped specimens were prepared from 3 CAD-CAM denture base resins (AvaDent, AV; Merz M-PM, M-PM; and Polident d.o.o, Poli) and a heat-polymerized polymethylmethacrylate resin (Promolux, CV) (n=10). Ra values of the specimens were measured by using a noncontact profilometer after conventional polishing. The color coordinates were also measured over a gray background with a spectrophotometer. Specimens were then consecutively subjected to simulated brushing for 20 000 cycles, CTC for 5000 cycles, and another 10 000 brushing cycles. Ra and color coordinates were measured after each interval. Color differences (ΔE00) were calculated by using the CIEDE2000 formula, and the data were analyzed by using 2-way analysis of variance and Tukey honestly significant difference tests (α=0.05).

RESULTS

The time interval had a significant effect on Ra (P<.001) as brushing cycles resulted in higher values than those at baseline and after CTC (P<.001). However, the differences between brushing cycles (P=.143) and between the baseline and after CTC (P=.994) were not significant. The interaction between the material type and time interval was significant for ΔE00 (P=.016). The only significant difference in ΔE00 values was observed between M-PM and CV after all treatments were completed (P=.029).

CONCLUSIONS

Brushing increased the Ra of all materials when compared with the baseline. All materials showed similar stainability throughout the brushing and CTC processes. However, M-PM CAD-CAM denture base resin underwent a greater color change after all treatments were completed than conventional denture base resin. All color changes can be considered clinically small, considering reported perceptibility and acceptability thresholds.

Effects of Surface-Etching Systems on the Shear Bond Strength of Dual-Polymerized Resin Cement and Zirconia

Adhesion of zirconia is difficult; thus, etching agents using several different methods are being developed. We investigated the effects of surface treatment with commercially available etching agents on the bond strength between zirconia and resin cement and compared them with those achieved using air abrasion alone. We used 100 zirconia blocks, of which 20 blocks remained untreated, 20 blocks were sandblasted, and 60 blocks were acid-etched using three different zirconia-etching systems: Zircos-E etching (strong-acid etching), smart etching (acid etching after air abrasion), and cloud etching (acid etching under a hot stream). Each group was subjected to a bonding procedure with dual-polymerized resin cement, and then 50 specimens were thermocycled. The shear bond strengths between the resin cement and zirconia before and after the thermocycling were evaluated. We observed that in the groups that did not undergo thermocycling, specimens surface-treated with solution did not show a significant increase in shear bond strength compared to the sandblasted specimens (p > 0.05). Among the thermocycled groups, the smart-etched specimens showed the highest shear bond strength. In the short term, various etching agents did not show a significant increase in bond strength compared to sandblasting alone, but in the long term, smart etching showed stability in bond strength (p < 0.05).

The Effect of Build Angle and Artificial Aging on the Accuracy of SLA- and DLP-Printed Occlusal Devices

The aim of this study is to investigate the influence of printing material, build angle, and artificial aging on the accuracy of SLA- and DLP-printed occlusal devices in comparison to each other and to subtractively manufactured devices. A total of 192 occlusal devices were manufactured by one SLA-printing and two DLP-printing methods in 5 different build angles as well as milling. The specimens were scanned and superimposed to their initial CAD data and each other to obtain trueness and precision data values. A second series of scans were performed after the specimens underwent an artificial aging simulation by thermocycling. Again, trueness and precision were investigated, and pre- and post-aging values were compared. A statistically significant influence was found for all main effects: manufacturing method, build angle, and thermocycling, confirmed by two-way ANOVA. Regarding trueness, overall tendency indicated that subtractively manufactured splints were more accurate than the 3D-printed, with mean deviation values around ±0.15 mm, followed by the DLP1 group, with ±0.25 mm at 0 degree build angle. Within the additive manufacturing methods, DLP splints had significantly higher trueness for all build angles compared to SLA, which had the highest mean deviation values, with ±0.32 mm being the truest to the original CAD file. Regarding precision, subtractive manufacturing showed better accuracy than additive manufacturing. The artificial aging demonstrated a significant influence on the dimensional accuracy of only SLA-printed splints.

Real-time imaging and quantitative analysis of internal gap formation in bulk-fill and conventional resin composites: An OCT evaluation

BACKGROUND

This study used optical coherence tomography (OCT) to observe real-time internal gap formation in both bulk-fill and conventional resin composites. It aimed to provide a quantitative analysis of variations, addressing the inconclusive nature of microleakage assessment caused by differences in testing methods.

METHODS

Fifty extracted third molars prepared with Class I cavities, were divided into five groups (n = 10). Conventional resin Filtek Z350 XT (FZX) was applied with a double-layer filling of 2 mm per layer. Bulk-fill resins X-tra fil (XTF), Filtek Bulk Fill Posterior Restorative (FBP), Surefil SDR Flow + (SDR), and Filtek Flowable Restorative (FFR) were applied with a single-layer filling of 4 mm. Real-time OCT imaging was conducted during light curing. Post-curing, the entire sample was OCT-scanned. Following this, ImageJ software was used to measure the gap (G1 %). Subsequently, thermal cycling (TC) (5000 times, 5 °C-55 °C) was applied, followed by OCT scanning to calculate the gap (G2 %) and ΔG%. Data were analyzed using two-way repeated measures ANOVA, Kruskal-Wallis test, and Duncan's test (α=0.05).

RESULTS

There was no significant difference in G1 % among the groups (p > 0.05). Following TC, FZX exhibited the highest G2 %, succeeded by FFR, FBP, XTF, and SDR, with SDR demonstrating the lowest G2 % (p < 0.05). FZX showed the highest ΔG% (p < 0.05), while SDR exhibited the lowest ΔG% (p < 0.05).

CONCLUSION

OCT proves to be a promising tool for detecting microleakage. TC exerted a more significant negative impact on conventional resin. Surefil SDR Flow + displayed the least microleakage, both before and after TC.

Surface treatment, liquid, and aging effects on color and surface properties of monolithic ceramics

PURPOSE

The purpose of this study was to investigate the effects of surface treatments, liquids, and aging on color, translucency, and surface properties of monolithic ceramics.

MATERIALS AND METHODS

Lithium disilicate (LDS) and zirconia-reinforced lithium silicate (ZLS) ceramics (n = 135 each) were cut and divided into three groups [crystallization+glaze (single stage), crystallization-glaze (two stages), and crystallization-polish (two stages)]. One sample from each group was examined using scanning electron microscopy (SEM). Remaining samples were divided into four subgroups (distilled water, coffee, grape juice, and smoothie) (n = 11 each), stored for 12 d in the respective liquids, and thermally aged. One sample from each subgroup was analyzed using SEM. The color, gloss, and roughness values of the samples were analyzed after surface treatment (initial) and storage under different liquids+aging conditions. The initial data and both the aged data and data change values were analyzed using robust two- and three-way analyses of variance.

RESULTS

The glazed groups exhibited smoother surfaces. Ceramic type and ceramic-surface treatment interactions affected the initial translucency parameter (TP) (P < .001) and the initial and aged roughness values (P ≤ .001). Surface treatment type affected the color change (P < .001), and ceramic type affected the aged TP values (P < .001). Type of ceramic, surface treatment, and their interactions affected both the initial and aged gloss (P ≤ .001) and TP change values (P ≤ .015). Surface treatment type and ceramic-surface treatment interactions affected the gloss change values (P ≤ .001).

CONCLUSION

Although both ceramics and all surface treatments are clinically applicable, crystallization-glaze is recommended. When gloss and smoothness are important or when translucency is important, ZLS or LDS may be preferred, respectively.

Effect of milling procedures in CAD-CAM systems on the color changes of CAD-CAM polymethyl methacrylate resin material as interim material

PURPOSE

This study aimed to investigate the effects of new and used burs on CAD-CAM PMMA resin color changes following thermocycling.

MATERIALS AND METHODS

Twenty disk-shaped specimens (10 × 2 mm) were made using a single brand of CAD-CAM polymethyl methacrylate resin (Polident) for the color test. Group N consisted of half of the specimens that were machined using the new tungsten carbide bur set, and Group U consisted of the specimens that were milled using the used bur set (500 machining time). A color test was performed on the specimens both before and after thermocycling. For the statistical analysis, the Kruskal-Wallis and Dunn Pairwise Comparison tests were employed.

RESULTS

The ∆E* value of specimens (2.057) milled with the used bur was higher than those of specimens milled with the new bur (0.340), but this value is within clinically acceptable limits. After thermocycling, specimens milled with the utilized burs had the greatest L* (93.850) and b* (5.000) values. After thermocycling, statistically significant differences were discovered between Group N and Group U as well as between specimens milled with the utilized bur before and after thermocycling.

CONCLUSION

Thermocycling process have an effect on the mean ∆E values of specimens milled with the used carbide bur, but these ∆E* values were not statistically significant.

CLINICAL SIGNIFICANCE

The color and clinical performance of CAD-CAM restorations may be affected by variations in CAD-CAM milling bur properties, particularly those related to their frequent use.

The Effect of Mechanical Alteration on Repair Bond Strength of S-PRG-Filler-Based Resin Composite Materials

This study investigates the impact of mechanical alteration on resin composite surfaces and its subsequent effect on repair bond strength. A total of 100 resin composite disks were prepared and were allocated for 24 h or 1 year of artificial aging. Specimens were embedded in epoxy resin, and the composite surfaces were mechanically altered using either diamond burs or air abrasion with aluminum oxide or glass beads. A universal bonding material was applied and a 2 mm circular and 3 mm high repair composite cylinder were prepared using a Teflon mold. Then, the specimens were tested for their shear bond strength, and the de-bonded specimens were observed under a scanning electron microscope to determine the failure pattern. SPSS 26.0 statistical software was used to analyze the data. Two-way ANOVA showed a statistically significant effect of mechanical alteration and aging on the shear bond strength of S-PRG-filler-based resin composite (p < 0.05). Surface modification with a fine diamond bur showed a significantly higher bond strength in both 24-h- and 1-year-aged specimens. Surface modification with alumina significantly increased the bond strength of 1-year-aged specimens; however, it was statistically insignificant for 24 h-aged specimens. Mechanical alteration with a fine diamond bur and 50-micron alumina can improve the repair bond strength of the composite.

Study on the mechanical and aging properties of an antibacterial composite resin loaded with fluoride-doped nano-zirconia fillers

Preventing the occurrence of secondary caries serves as one of the significant issues in dental clinic, thus make it indispensable to improving the properties of conventional composite resin (CR) by developing a novel CR. In present study, two groups of experimental CRs loaded with different contents of fluoride-doped nano-zirconia fillers (25 wt% and 50 wt%) were fabricated. The surface topography, mechanical performance, fluoride release, antibacterial effect, aging property and cytotoxicity of the experimental CRs were evaluated subsequently. A uniform distribution of the F-zirconia fillers over the whole surface of resin matrix could be observed. The experimental CRs showed continuous fluoride release within 28 days, which was positively correlated with the content of F-zirconia fillers. Moreover, the amount of fluoride release increased in the acidic buffer. Addition of F-zirconia fillers could improve the color stability, wear resistance and microhardness of the experimental CRs, without reducing the flexure strength. Furtherly, the fluoride ions released continuously from the experimental CRs resulted in effective contact and antibacterial properties, while they showed no cytotoxicity. As a consequence, considerations can be made to employ this new kind of composite resin loaded with fluoride-doped nano-zirconia fillers to meet clinical requirements when the antimicrobial benefits are desired.

Nanoparticle-Modified 3D-Printed Denture Base Resins: Influence of Denture Cleansers on the Color Stability and Surface Roughness In Vitro

This study aimed to evaluate the influence of denture cleansers on the color, stability, and surface roughness of three-dimensional (3D)-printed denture base resins modified with zirconium dioxide nanoparticles (nano-ZrO2). A total of 440 specimens were fabricated using one heat-polymerized resin, and two 3D-printed resins (NextDent and ASIGA). According to the nano-ZrO2 content, the specimens for each resin were divided into five groups (0%, 0.5%wt, 1%wt, 3%wt, and 5%wt). Each concentration was divided into four subgroups (n = 10) based on the immersion solution (distilled water, sodium hypochlorite, Corega, and Fittydent) and immersion duration (360 and 720 days). The color changes (∆E00) and surface roughness (Ra, µm) of each specimen were measured at different time intervals (base line, 360 days, 720 days) using a spectrophotometer and a non-contact profilometer, respectively. The results were statistically analyzed using ANOVA and a post hoc Tukey's test (α = 0.05). Sodium hypochlorite showed the highest significant color change of all the denture base resins (p < 0.001). The average value of ΔE00 for sodium hypochlorite was significantly higher than the values for the other solutions (Fittydent, Corega, and water) (p < 0.001). Color stability was significantly affected by immersion time for all types of solutions except Corega (p < 0.001). All of the tested immersion solutions (distilled water, sodium hypochlorite, Corega, and Fittydent) showed a significant increase in the surface roughness of all the denture base resins (p < 0.05). Surface roughness was substantially increased by immersion time for all types of solution except Fittydent (p < 0.001). Denture cleansers can result in substantial color change and affect the surface roughness of unmodified and nanoparticle-modified denture base resins. Therefore, the selection of denture cleanser and appropriate types of material is critical for denture longevity.

Effect of fiber-reinforced direct restorative materials on the fracture resistance of endodontically treated mandibular molars restored with a conservative endodontic cavity design

OBJECTIVE

This study aimed to evaluate the fracture strength of teeth restored using fiber-reinforced direct restorative materials after endodontic treatment with a conservative mesio-occlusal access cavity design.

MATERIALS AND METHODS

A total of 100 extracted intact mandibular first molars were selected and distributed into a positive control group where teeth left intact and the following four test groups comprised of teeth with conservative mesio-occlusal access cavities that had undergone root canal treatment (n = 20/group): access cavity without restoration (negative control), bulk-fill resin composite with horizontal glass fiber post reinforcement, fiber-reinforced composite with bulk-fill resin and bulk-fill resin composite. Following thermocycling (10,000 cycles), fracture resistance was measured using a universal testing machine. Statistical analyses (one-way analysis of variance and the Tamhane test) were performed, and statistical significance was set at p < 0.05.

RESULTS

Groups with minimally invasive access cavities had lower fracture strength than intact teeth, regardless of the restoration material (p < 0.05). Fiber-reinforced composite groups demonstrated higher fracture strength than bulk-fill resin composite alone (p < 0.05). Fracture types varied among groups, with restorable fractures predominant in the fiber-reinforced composite groups.

CONCLUSION

This study suggests that using fiber-reinforced composite materials, especially in combination with bulk-fill resin composites, can effectively enhance the fracture strength of endodontically treated teeth with conservative access cavities. However, using only bulk-fill resin composite is not recommended based on the fracture strength results.

CLINICAL SIGNIFICANCE

When teeth that undergo endodontic treatment are restored using a conservative access cavity design and fiber-reinforced composite materials, especially in combination with bulk-fill resin composites, the fracture strength of the teeth can be effectively increased.

Effect of preparation design and endodontic access on fracture resistance of zirconia overlays in mandibular molars: An in vitro study

PURPOSE

To evaluate the fracture resistance of zirconia overlays, considering various preparation designs and the presence of endodontic access.

MATERIALS AND METHODS

Ninety translucent zirconia (5Y-PSZ) overlay restorations were divided into six groups (n = 15/group) based on different preparation designs, with and without endodontic access: chamfer margin 4 mm above the gingival level without (group 1) and with endodontic access (group 2); margin 2 mm above the gingival level without (group 3) and with endodontic access (group 4); overlay with no chamfer margin without (group 5) and with endodontic access (group 6). Restorations were bonded to mandibular first molar resin dies, and the groups with endodontic access were sealed with flowable resin composite. All restorations underwent 100,000 cycles of thermal cycling between 5°C and 55°C, followed by loading until fracture. Maximum load and fracture resistance were recorded. ANOVA with Tukey post-hoc tests were used for statistical comparison (α < 0.05).

RESULTS

Fracture resistance significantly varied among overlay designs with and without endodontic access (p < 0.001), except for the no-margin overlays (groups 5 and 6). Overlays with a 2 mm margin above the gingival margin with endodontic access (group 4) exhibited significantly higher fracture resistance compared to both the 4-mm supragingival (group 2) and no-margin (group 6) designs, even when compared to their respective intact groups (groups 1 and 5). There were no significant differences between the no-margin and 4-mm supragingival overlays.

CONCLUSION

The more extensive zirconia overlay for mandibular molars is the first choice since the 2 mm margin above the gingival level design withstood considerable loads even after undergoing endodontic access. A no-margin overlay is preferred over the 4-mm supragingival design as it preserves more tooth structure and there was no outcome difference, irrespective of endodontic access. Caution is warranted in interpreting these findings due to the in vitro nature of the study.

Effect of surface treatment and resin cement type on the bond strength of polyetheretherketone to lithium disilicate ceramic

BACKGROUND

This study aims to evaluate the effect of surface treatment and resin cement on the shear bond strength (SBS) and mode of failure of polyetheretherketone (PEEK) to lithium disilicate ceramic (LDC). This is suggested to study alternative veneering of PEEK frameworks with a ceramic material.

METHODS

eighty discs were prepared from PEEK blank and from lithium disilicate ceramic. Samples were divided into four groups according to surface treatment: Group (A) air abraded with 110 μm Al2O3, Group (AP) air abrasion and primer application, Group (S) 98% sulfuric acid etching for 60 s, Group (SP) Sulfuric acid and primer. Each group was subdivided into two subgroups based on resin cement type used for bonding LDC:1) subgroup (L) self- adhesive resin cement and 2) subgroup (B) conventional resin cement (n = 10). Thermocycling was done for all samples. The bond strength was assessed using the shear bond strength test (SBS). Failure mode analysis was done at 50X magnification with a stereomicroscope. Samples were chosen from each group for scanning electron microscope (SEM). The three-way nested ANOVA followed by Tukey's post hoc test were used for statistical analysis of results. Comparisons of effects were done utilizing one way ANOVA and (p < 0.05).

RESULTS

The highest mean of shear bond strength values was demonstrated in Group of air abrasion with primer application using conventional resin cement (APB) (12.21 ± 2.14 MPa). Sulfuric acid groups showed lower shear bond strength values and the majority failed in thermocycling especially when no primer was applied. The failure mode analysis showed that the predominant failure type was adhesive failure between cement and PEEK, while the remaining was mixed failure between cement and PEEK.

CONCLUSION

The air abrasion followed by primer application and conventional resin cement used for bonding Lithium Disilicate to PEEK achieved the best bond strength. Primer application did not have an effect when self-adhesive resin cement was used in air-abraded groups. Priming step is mandatory whenever sulfuric acid etching surface treatment is utilized for PEEK.

The effects of re-irradiation on the chemical and morphological properties of permanent teeth

This study aimed to assess the in vitro effects of re-irradiation on enamel and dentin properties, simulating head and neck cancer radiotherapy retreatment. Forty-five human permanent molars were classified into five groups: non-irradiated; irradiated 60 Gy, and re-irradiated with doses of 30, 40, and 50 Gy. Raman spectroscopy, scanning electron microscopy (SEM), and energy dispersive x-ray spectroscopy (EDS) were employed for analysis. Raman spectroscopy assessed intensity, spectral area, and specific peaks comparatively. Statistical analysis involved Kolmogorov-Smirnov and One-Way ANOVA tests, with Tukey's post-test (significance level set at 5%). Significant changes in irradiated, non-irradiated, and re-irradiated enamel peaks were observed, including phosphate (438 nm), hydroxyapatite (582 nm), phosphate (960 nm), and carbonate (1070 nm) (p < 0.05). Re-irradiation affected the entire tooth (p > 0.05), leading to interprismatic region degradation, enamel prism destruction, and hydroxyapatite crystal damage. Dentin exhibited tubule obliteration, crack formation, and progressive collagen fiber fragmentation. EDX revealed increased oxygen percentage and decreased phosphorus and calcium post-reirradiation. It is concluded that chemical and morphological changes in irradiated permanent teeth were dose-dependent, exacerbated by re-irradiation, causing substantial damage in enamel and dentin.

Prolonged post-washing in ethanol decreases bond strength of additively manufactured crown materials

OBJECTIVES

This study aimed to investigate the effect of post-washing duration and crown thickness on the bond strength between additively manufactured crown materials and dental cement in vitro.

METHODS

Rectangular-shaped specimens of two thicknesses (1.5 and 2.0 mm) were additively manufactured from permanent VarseoSmile Crown (VC) and long-term temporary NextDent (ND) materials. The specimens were post-washed (n = 160) in ethanol for 5 min, 10 min, 1 h, and 8 h then cemented with dual-cure resin cement. Twenty PMMA (TC) were milled as a control. A chevron-notch test was performed to measure the maximum load until failure (N). Interfacial bond strength (J/m2) was calculated and statistically analysed. The mode of failure was analysed by scanning electron microscopy (SEM).

RESULTS

There was a significant difference in the bond strength between all groups (p < 0.01). VC at 1.5mm thickness post-washed for 10 min showed the highest mean bond strength (1.77 ±0.96 J/m2) while VC at 2.0mm thickness post-washed for 8 h showed the lowest (0.22 ±0.10 J/m2). Exposure to ethanol for 8 h resulted in lower bond strength. Within the type of material, there were no differences in bond strength between the thicknesses when post-washed for the same duration.

CONCLUSIONS

Prolonged post-washing of AM crown materials can significantly decrease the bond strength to resin cement. There were no differences between the permanent and long-term temporary AM materials. When post-washed for 5 min, AM materials observed comparable or higher bond strength values compared to PMMA.

CLINICAL SIGNIFICANCE

The output of this research serves as a guide for dental practitioners, emphasising the importance of adhering to correct post-washing procedures for optimal bond strength of additively manufactured crown materials.

Effect of coffee thermocycling on the color and translucency of milled and 3D printed definitive restoration materials

STATEMENT OF PROBLEM

Research on the color and translucency properties of 3-dimensionally (3D) printed definitive resins and the effect of coffee thermocycling on these properties is lacking.

PURPOSE

The purpose of this in vitro study was to investigate the effect of coffee thermocycling on the color and translucency parameters of the milled and 3D printed materials used for definitive restorations.

MATERIAL AND METHODS

Plate-shaped specimens (12×12×1 mm) of 3 milled (IPS e.max CAD (LDS), Vita Enamic (PICN), Cerasmart (RNC)) and two 3D printed (VarseoSmile Crownplus (VSP), Permanent Crown (PC)) were fabricated (n=12). The brightness (L*), red-green (a*), and yellow-blue (b*) parameters were measured with a spectrophotometer before and after 10 000 coffee thermocycles. The relative translucency parameters (RTP00) and color change were calculated using the CIEDE2000 formula. Stainability (ΔE00) and translucency differences (ΔRTP00) were evaluated. Data were analyzed with the Kruskal-Wallis, Mann-Whitney U, and Wilcoxon tests. The Spearman correlation test was used to analyze the ΔE00 and ΔRTP00 values (α=.05).

RESULTS

The type of material and coffee thermocycling significantly affected the evaluated parameters at both measurement periods (P=.001). Coffee thermocycling decreased the L* and RTP00 values while increasing the a* and b* values (P=.001). The highest ΔE00 values were found in VSP and PC, which were statistically similar (P=.291), while the highest | ΔRTP00 | values were observed for VSP (P=.001). The lowest ΔE00 and | ΔRTP00 | values were found in LDS (P=.001). A positive relationship was found between the ΔE00 and | ΔRTP00| values (R=.590, P=.01).

CONCLUSIONS

After coffee thermocycling, all tested materials exhibited a darkened, yellowish, and opaque appearance, although the alterations in color and translucency remained within clinically acceptable thresholds (AT00=1.81) for these materials.

Factors influencing the bond strength of additively manufactured crown materials in dentistry: A systematic review of in vitro studies

OBJECTIVE

The purpose of this systematic review was to investigate how different interventions can impact the bond strength of additively manufactured crown materials after cementation.

DATA/SOURCES

Four online databases Ovid MEDLINE, Scopus, Web of Science and Google Scholar were searched up to January 2023. Inclusion criteria were English-language publications, full-text, and in vitro studies only. Exclusion criteria were studies that did not assess the bonding of an additively manufactured crown material to cement or did not conduct any bond strength tests. An assessment of risk of bias was done in accordance with a modified Consolidated Standards of Reporting Trials (CONSORT) checklist. Each study was analysed and compared based on the interventions and bond strength results.

STUDY SELECTION

Six studies satisfied the inclusion and exclusion criteria, five of which evaluated photopolymerised resin and one that tested zirconia manufacturing via 3D printing. All studies observed a low risk of bias. The interventions applied included the type of surface pretreatments, airborne-particle abrasion pressure, cement type, taper of crown, and artificial aging. Three studies compared the bonding performance to milled materials.

CONCLUSIONS

The bond strength of crown materials additively manufactured from photopolymers presented high values and are comparable to milled materials. The systematic review demonstrated there was no definite superior cement type, but airborne-particle abrasion with alumina was generally recommended. There is a clear gap in the literature regarding the bond strength of additively manufactured crowns. Therefore, further research is necessary to evaluate its clinical applicability for permanent restorations.

CLINICAL SIGNIFICANCE

Factors influencing the bond strength of additively manufactured crown materials should be evaluated so dental professionals can adopt procedures that promote the strongest bond.