Solid phase microextraction devices prepared on plastic support as potential single-use samplers for bioanalytical applications

Quantification of prohibited substances and endogenous corticosteroids in saliva using traditional, alternative microextraction-based, and novel 3D printed sample-preparation methods coupled with LC-MS

Oral fluid has gained significant interest as an alternative matrix for drug testing due to its easy and non-invasive collection. Despite these advantages, achieving suitably low limits of detection remains a clear challenge in the use of oral fluids for drug screening. In this study, we demonstrate that the application of commercially available SPME fibers followed by liquid chromatography tandem mass spectrometry can enable the comprehensive detection and confirmation of drugs in oral fluid samples. To this end, we develop and test a sample-preparation protocol for a panel of 46 drugs covering the most popular drugs of abuse and doping agents available worldwide. Human saliva samples were collected using a Salivette® device (CE IVD certified) and sampled using SPME devices coated with a C18 extraction phase. The proposed protocol was validated with respect to its lower limits of quantification (LLOQ), linearity, matrix effects, precision, and extraction recovery. Linearity was confirmed for all compounds (R2 > 0.97), except for testosterone (R2 = 0.953) and metandrostenolon (R2 = 0.958). Furthermore, 4 compounds suffered from matrix effects, with less than 10 % deviation from acceptance criteria. After analytical validation, saliva samples from volunteers were analyzed to determine free concentrations of cortisol at different times after awaking. Finally, a 3D-printed prototype device was designed and successfully applied to extract small molecules, thus demonstrating a new modern low-cost approach for bioanalysis.

Developing and Evaluating the Greenness of a Reliable, All-in-One Thin-Film Microextraction Protocol for Determining Fentanyl, Methadone, and Zolpidem in Plasma, Urine, and Oral Fluid

This paper proposes an all-in-one microextraction-based protocol capable of determining and quantifying fentanyl, methadone, and zolpidem in plasma, urine, and saliva at concentrations below those required by international regulatory organizations. A homemade thin-film microextraction device featuring an octyl-cyanopropyl stationary phase was coupled with LC-MS/MS. The proposed method was developed and validated according to FDA criteria, providing extraction efficiency values ranging from 26.7% to 76.2% with no significant matrix effects (2.6% to 15.5% signal suppression). The developed protocol provided low limits of quantification (mostly equal to 1 ng mL-1) and good reproducibility (intra- and inter-day RSDs of less than 9.6% and 12.0%, respectively) and accuracy (89% to 104% of the test concentration). An assessment of the protocol's environmental impact indicated that attention must be devoted to eliminating the use of toxic reagents and developing its capability for in situ sampling and in-field analysis using portable instruments. The proposed TFME-based protocol provides clinical laboratories with a versatile, one-step tool that enables the simultaneous monitoring of fentanyl, methadone, and zolpidem using the most popular biological matrices.

Direct Coupling of SPME to Mass Spectrometry

Solid-phase microextraction devices are normally analyzed by gas or liquid chromatography. Their use has become increasingly widespread since their introduction in 1990, and nowadays most analytical laboratories use or have used SPME as an efficient and green method to perform analyte extraction and sample clean-up in one step. The SPME technique is intrinsically flexible, and allows for a high degree of optimization with regard to the extracting phase, as well as the way sample is analyzed. Since its introduction, researchers have been trying different ways to transfer analytes extracted from the solid phase to a mass spectrometer, with the aim to increase throughput and reduce solvent, gas usage and costs associated with conventional chromatographic techniques. Furthermore, but not less important, for pure fun of developing new, more efficient and sensitive analytical strategies! This chapter aims at providing a comprehensive overview of the most relevant non-chromatographic mass spectrometric approaches developed for SPME. Technical aspects of each SPME-MS approach will be discussed, highlighting their advantages, disadvantages and future potential developments. Particular emphasis will be given on the most recent direct coupling approaches using novel ionization approaches, and a concise overview of the existing applications will also be provided.

Non-invasive Sampling of Human Body Fluids Using In Vivo SPME

Noninvasive body fluids offer attractive sources to gain insights into human health. The in vivo solid-phase microextraction (SPME) technique is a fast and versatile sample preparation technique for the noninvasive sampling of human body fluids in various fields. This chapter summarizes the applications of SPME coupled with mass spectrometry (MS)-based approaches for noninvasive investigations of human body fluids, including urine, sweat, and saliva. New features of noninvasive SPME sampling and MS-based analysis are highlighted, and the prospects on their further development are also discussed.

Green Analytical Toxicology for the Determination of Cocaine Metabolites

Brazil is the third largest contributor to Green Analytical Chemistry, and there is significant participation of toxicologists in the development and improvement of environmental techniques. Currently, toxicologists have their own strategies and guidelines to promote the reduction/replacement or elimination of solvents, reduce the impacts of derivatization and save time, among other objectives, due to the peculiarities of toxicological analysis. Thus, this review aims to propose the concept of Green Analytical Toxicology and conduct a discussion about its relevance and applications specifically in forensic toxicology, using the microextraction methods developed for the determination of cocaine and its metabolites as examples.

Designing an "all-in-one" microextraction capsule device for the liquid chromatographic-fluorescence determination of doxorubicin and its metabolites in rat plasma

In this study, an "all-in-one" microextraction device was designed and fabricated for the extraction of doxorubicin and its two metabolites from rat plasma prior to their determination by high performance liquid chromatography coupled to fluorescence detector. A sol-gel-based sorbent was synthesized in situ and incorporated within two conjoined porous polypropylene tubes together with a cylindrical magnetic bar in order to avoid the need of an external stirring bar. Among other sorbents investigated, the moderately polar sol-gel poly(tetrahydrofuran) was found to be advantageous due to its high affinity toward the target analytes. Systematic investigation of the critical parameters affecting the adsorption and the desorption step was carried out. Due to the "built-in" filtration mechanism of the porous microextraction capsules, the isolation of the analytes was performed directly in the plasma matrix without any previous sample pretreatment (i.e., protein precipitation, centrifugation, etc.). The proposed method was validated in terms of linearity, accuracy, precision, specificity, sensitivity, and stability according to the FDA guidelines. The limits of detection ranged between 1 - 2 ng mL^-1 while the lower limits of quantitation of the analytes were calculated as 10 ng mL^-1. The accuracy (% relative error) was found within -9.7 - 15.3% under both intra- and inter-day conditions. The precision was better than 13.4% in all cases. ComplexGAPI index was employed to present the green attributes of the developed protocol from the preparation of the microextraction device to the final determination of the analytes. Finally, the applicability of the fabricated stand-alone extraction device was demonstrated in the analysis of the target analytes in rat plasma after intravenous administration of doxorubicin in order to assess its pharmacokinetic profile.

Rapid and One-Step Screening of Taxane Compounds by a Two-Dimensional Carbon Microfiber Fractionation System Combined with Tandem Mass Spectrometry

Taxane compounds have attracted wide attention due to the basic chemical structure of taxol as an alternative anticancer drug. The full-scan tandem mass spectrometry (MS/MS) fragmentation behaviors of seven taxane compounds were studied. For taxanes of Sc-T and Sc-T-Xyl types, diagnostic product ions are originated from a cleavage in the ester bond of the C₁₃ position and the C-O bond of the C₇ position, and the subsequent fragmentation pattern is similar to those of M-type taxanes with the loss of different numbers of acetic acid moieties (AcOH), benzoic acid moieties (BzOH), and H₂O molecules. A rapid (7 min) and one-step screening method of two-dimensional microscale carbon fiber and active carbon fiber columns combined with tandem mass spectrometry (2DμCFs-MS/MS) was developed for the screening of taxane compounds from Taxus cuspidata samples. Before MS/MS analysis, the 2DμCFs system can group the sample extract without any pretreatment into three chromatographic-type fractions of strong, medium, and weak polarity to avoid matrix interference, such as lipids and pigments. The 2DμCFs-MS/MS can also conduct qualitative and quantitative analysis of taxane compounds, which is evaluated by limits of detection ranging from 3 to 50 ng mL^-1, limits of quantitation ranging from 10 to 150 ng mL^-1, satisfactory recoveries from 75.2 to 112.2%, and reproducibilities with relative standard deviations from 1.4 to 11.7%.

Matrix compatibility of typical sol-gel solid-phase microextraction coatings in undiluted plasma and whole blood for the analysis of phthalic acid esters

Sol-gel materials have been widely used for solid-phase microextraction (SPME) coatings due to their outstanding performance; in contrast, sol-gel SPME coatings have seldom been used for in vivo sampling. The main reason is that their matrix compatibility is unclear. In order to promote the application of this type of coating and accelerate the development of in vivo SPME, in this study, the matrix compatibility of several typical sol-gel coatings was assessed in plasma and whole blood using phthalic acid esters as analytes. The service life of five kinds of sol-gel coatings was among 20-35 times in undiluted plasma, while it was 27 times for a homemade commercial polydimethylsiloxane coating, which indicates good matrix compatibility of sol-gel coatings in untreated plasma. The sol-gel hydroxy-terminated silicone oil/methacrylic acid fiber achieved the highest extraction ability among all of the fibers, and it was tested in pig whole blood. It could be continuously used for at least 22 times, demonstrating good potential for in vivo sampling. Subsequently, a direct-immersion SPME/gas chromatography-flame ionization detection method was established for the determination of 5 phthalic acid esters in blood. Compared with other methods reported in the literature, this method is rapid, simple, sensitive, and accurate, and does not need expensive instruments or tedious procedures. A simulation system of animal blood circulation was constructed to verify the practicability of sol-gel SPME coatings in animal vein sampling. The result illustrated the feasibility of that coating for in vivo blood sampling, but a more accurate quantification calibration approach needs to be explored.

Polyamide Noncoated Device for Adsorption-Based Microextraction and Novel 3D Printed Thin-Film Microextraction Supports

Polyamide noncoated device for adsorption-based microextraction (PANDA microextraction) is a brand new, easy to prepare, environmentally friendly, inexpensive, and efficient sample preparation method created entirely with the use of 3D printing. The proposed method is based on the extractive proprieties of the unmodified polyamide and carbon fiber blends and is compared with the highly selective thin-film microextraction (TFME). In addition, 3D printing was used to simplify the process of TFME. Prototype sample preparation devices were evaluated by the extraction of oral fluid spiked with 38 small molecules with diverse chemical natures, such as lipophilicity in the log P range of 0.2–7.2. The samples were analyzed by high-performance liquid chromatography coupled with tandem mass spectrometry. The results indicate that chemically and thermally resistant 3D printed supports can be successfully used as a cost-saving, environmentally friendly solution for the preparation of TFME devices, alternative to the conventional metal supports, with only marginal differences in the extraction yield (mean = 4.0%, median = 1.8%, range = 0.0–22.3%, n = 38). Even more remarkably, in some cases, the newly proposed PANDA microextraction method exceeded the reference TFME in terms of the extraction efficacy and offered excellent sample cleanup as favorable matrix effects were observed (mean = −8.5%, median = 7.5%, range = −34.7–20.0%, n = 20). This innovative approach paves the road to the simplified sample preparation with the use of emerging extractive 3D printing polymers.

Optimizing a High-Throughput Solid-Phase Microextraction System to Determine the Plasma Protein Binding of Drugs in Human Plasma

Plasma protein binding refers to the binding of a drug to plasma proteins after entering the body. The measurement of plasma protein binding is essential during drug development and in clinical practice, as it provides a more detailed understanding of the available free concentration of a drug in the blood, which is in turn critical for pharmacokinetics and pharmacodynamics studies. In addition, the accurate determination of the free concentration of a drug in the blood is also highly important for therapeutic drug monitoring and in personalized medicine. The present study uses C₁₈-coated solid-phase microextraction 96-pin devices to determine the free concentrations of a set of drugs in plasma, as well as the plasma protein binding of drugs with a wide range of physicochemical properties. It should be noted that the extracted amounts used to calculate the binding constants and plasma protein bindings should be measured at respective equilibrium for plasma and phosphate buffer. Therefore, special attention is placed on properly determining the equilibration times required to correctly estimate the free concentrations of drugs in the investigated systems. The plasma protein binding values obtained with the 96-pin devices are consistent with those reported in the literature. The 96-pin device used in this research can be easily coupled with a Concept96 or other automated robotic systems to create an automated plasma protein binding determination protocol that is both more time and labor efficient compared to conventional equilibrium dialysis and ultrafiltration methods.

Benefits of Innovative and Fully Water-Compatible Stationary Phases of Thin-Film Microextraction (TFME) Blades

Octadecyl (C₁₈) groups are arguably the most popular ligands used for preparation of solid phase microextraction (SPME) devices. However, conventional C₁₈-bonded silica particles are not fully compatible with the nearly 100% aqueous composition of typical biological samples (e.g., plasma, saliva, or urine). This study presents the first evaluation of thin-film SPME devices coated with special water-compatible C₁₈-bonded particles. Device performance was assessed by extracting a mixture of 30 model compounds that exhibited various chemical structures and properties, such as hydrophobicity. Additionally, nine unique compositions of desorption solvents were tested. Thin-film SPME devices coated with C₁₈-bonded silica particles with polar end-capping groups (10 µm) were compared with conventional trimethylsilane end-capped C₁₈-bonded silica particles of various sizes (5, 10, and 45 µm) and characteristics. Polar end-capped particles provided the best extraction efficacy and were characterized by the strongest correlations between the efficacy of the extraction process and the hydrophobicity of the analytes. The results suggest that the original features of octadecyl ligands are best preserved in aqueous conditions by polar end-capped particles, unlike with conventional trimethylsilane end-capped particles that are currently used to prepare SPME devices. The benefits associated with this improved type of coating encourage further implementation of microextractraction as greener alternative to the traditional sample preparation methods.

Thin film molecularly imprinted polymer (TF-MIP), a selective and single-use extraction device for high-throughput analysis of biological samples

Enhancing selectivity, reducing matrix effects and increasing analytical throughput have been the main objectives in the development of biological sample preparation techniques. A thin film molecularly imprinted polymer (MIP) is employed for extraction and analysis of tricyclic antidepressants (TCAs) as a model class of compounds in human plasma for the first time to reach the abovementioned goals. The thin film MIPs prepared on a metal substrate can be used directly for extraction from biological matrices with no sample manipulation steps and no pre-conditioning. This method was validated with good linearity (R² > 0.99 in 1.0-500.0 ng mL^-1 range), excellent accuracy (90% -110%) and precision (RSD % value less than 15%) in pooled human plasma samples (N = 3). The limits of quantitation (LOQ) for TCAs in plasma samples were between 1.0-5.0 ng mL^-1 which are lower than the therapeutic ranges of these drugs. Kinetic and isotherm studies showed the superior performance of MIP sorbent compared to a non-imprinted polymer (NIP) sorbent in extracting TCAs from a bovine serum albumin (BSA) solution. The optimized and validated method for pooled human plasma was utilized for monitoring the concentration of TCAs in three patient samples who had been prescribed TCAs. These selective single-use thin film extraction devices are promising for efficient and fast procedures for analyzing biological samples.

Applications of porous frameworks in solid-phase microextraction

Porous frameworks are a term of attracting solid materials assembled by interconnection of molecules and ions. These trendy materials due to high chemical and thermal stability, well-defined pore size and structure, and high effective surface area gained attention to employ as extraction phase in sample pretreatment methods before analytical analysis. Solid-phase microextraction is an important subclass of sample preparation technique that up to now different configurations of this method have been introduced to get adaptable with different environments and analytical instruments. In this review, theoretical aspect and different modes of solid-phase microextraction method are investigated. Different classes of porous frameworks and their applications as extraction phase in the proposed microextraction method are evaluated. Types and features of supporting substrates and coating procedures of porous frameworks on them are reviewed. At the end, the prospective and the challenges ahead in this field are discussed.

Assessment of solid phase microextraction as a sample preparation tool for untargeted analysis of brain tissue using liquid chromatography-mass spectrometry

This work presents an evaluation of solid-phase microextraction (SPME) SPME in combination with liquid chromatography-high resolution mass spectrometry (LC-HRMS) as an analytical approach for untargeted brain analysis. The study included a characterization of the metabolite coverage provided by C18, mixed-mode (MM, with benzene sulfonic acid and C18 functionalities), and hydrophilic lipophilic balanced (HLB) particles as sorbents in SPME coatings after extraction from cow brain homogenate at static conditions. The effects of desorption solvent, extraction time, and chromatographic modes on the metabolite features detected were investigated. Method precision and absolute matrix effects were also assessed. Among the main findings of this work, it was observed that all three tested coating chemistries were able to provide comparable brain tissue information. HLB provided higher responses for polar metabolites; however, as these fibers were prepared in-house, higher inter-fiber relative standard deviations were also observed. C18 and HLB coatings offered similar responses with respect to lipid-related features, whereas MM and C18 provided the best results in terms of method precision. Our results also showed that the use of methanol is essential for effective desorption of non-polar metabolites. Using a reversed-phase chromatographic method, an average of 800 and 1200 brain metabolite features detected in positive and negative modes, respectively, met inter-fibre RSD values below 30% (n=4) after removal of fibre and solvent artefacts from the associated datasets. For features detected using a lipidomics method, a total of 900 and 1800 features detected using C18 fibers in positive and negative mode, respectively, met the same criteria. In terms of absolute matrix effects, the majority of the model metabolites tested showed values between 80 and 120%, which are within the acceptable range. Overall, the findings of this work lay the foundation for further optimization of parameters for SPME-LC-HRMS methods suitable for in vivo and ex vivo brain (and other tissue) untargeted studies, and support the applicability of this approach for non-destructive tissue metabolomics.

Therapeutic drug monitoring of tranexamic acid in plasma and urine of renally impaired patients using solid phase microextraction

The purpose of the research was to develop an improved solid phase microextraction (SPME)-based sampling protocol for the therapeutic drug monitoring of tranexamic acid (TXA) from plasma and urine of patients with chronic renal dysfunction (CRD) in order to correct the current dosing schedule to accommodate these patients. A 12-fold improvement in sampling efficiency (25 min for 96 samples -22 s per sample) was achieved with the use of hydrophilic-lipophilic balance (HLB)-coated SPME devices, thereby enabling high throughput profiling of TXA in the plasma and urine of 49 CRD patients undergoing cardiac surgery. A limit of quantification of 10 μg/mL and 25 μg/mL was obtained for plasma and urine respectively while a method accuracy of 103-105% and a precision of less than 8% was achieved. The results from this study were ultimately used by clinicians at the Toronto General Hospital to design a corrective pharmacokinetic dosing schedule for CRD patients. This green method further presents potential application in the clinical field for the fast high throughput monitoring of TXA not only in plasma but also in urine - a biological matrix seldom explored for the analysis of TXA - without the need for solvent-assisted extraction, extensive sample pre-treatment or clean-up, derivatization or excessive pH adjustment to improve amenability for analytical separation.

Nanoparticle-based polyacrylonitrile monolithic column for highly efficient micro solid-phase extraction of carotenoids and vitamins in human serum

In this work, a biocompatible monolithic column based micro-solid-phase extraction (µ-SPE) method was developed for biological fluid analysis. A novel nanoparticle-based polyacrylonitrile monolithic column (C30 NP-PMC) was fabricated by incorporating triacontyl (C30) modified silica nanoparticles (NPs) into the polyacrylonitrile monolithic matrix through thermally induced phase separation. With efficient mass transfer and sorption capacity, C30 NP-PMC exhibited outstanding performance for the extraction of carotenoids and fat-soluble vitamins (FSVs) from human serum samples, superior to commercial C18 cartridges as well as liquid-liquid extraction (LLE) method. Under optimal conditions, the proposed µ-SPE method coupled with high-performance liquid chromatography-diode array detection (HPLC-DAD) achieved satisfactory limits of detection (LODs) (1.5-75.0 ng/mL) and good recoveries (85.0-106.5 %) with relative standard deviations (RSDs) of less than 12.1% by consuming lower sorbent (35.0 mg) and organic solvent (0.8 mL). Successful application of the developed method demonstrated the great potential of such monolithic sorbents for efficient isolation and preconcentration of trace analytes from blood samples.

Electrochemically synthesized NiFe layered double hydroxide modified Cu(OH)2 needle-shaped nanoarrays: A novel sorbent for thin-film solid phase microextraction of antifungal drugs

Herein, we applied a simple electrosynthesis process to deposit nickel-iron layered double hydroxides (NiFe LDH) on the surface of copper hydroxide (Cu(OH)₂) needle-shaped nanoarrays and introduce a new sorbent for thin-film solid phase microextraction (TF-SPME). For this purpose, the nanoarrays were grown via electrochemical anodization on a copper foil's surface and then modified with NiFe LDH. The synthesized sorbent was characterized by field emission-scanning electron microscopy, Brunauer-Emmett-Teller (BET), and Barrett-Joiner-Halenda (BJH) analysis, energy-dispersive X-ray spectroscopy, and X-ray diffraction. The Cu(OH)₂-NiFe LDH based TF-SPME method was used to measure antifungal drugs in veterinary plasma samples followed by HPLC-UV analysis. The effects of various parameters in the extraction efficiency, including pH (5.0), extraction time (20 min), stirring rate (500 rpm), and salt effect (5.0%), type of eluent (acetonitrile), eluent volume (100 μL) and desorption time (5 min) were thoroughly optimized. Under the optimum conditions, limits of detection for ketoconazole, clotrimazole, and miconazole were obtained below 10 ng mL^-1. Intra-day, inter-day and film-to-film RSDs% were obtained less than 6.2%, 7.3% and 7.0%, respectively. Moreover, calibration plots were linear from 30 to 5000 ng mL^-1 for ketoconazole, 8.0-1000 ng mL^-1 for clotrimazole, and 15-1000 ng mL^-1 for miconazole, with determination coefficients between 0.9937 and 0.9971. Finally, good relative recoveries (%) in the range of 85-97% were obtained for measuring trace amounts of antifungal drugs in dogs' plasma samples. As a result, the method can be considered as an appropriate alternative to the conventional sample preparation methods for measuring trace amounts of antifungal drugs in biological samples.

Green analytical solutions for sample preparation: solid phase microextraction and related techniques

For at least three decades, the analytical chemistry community is striving to apply the principles of Green Chemistry to the development of analytical methods. Many efforts have been made to outline the concept of Green Analytical Chemistry, which helped to redefine analytical procedures and drastically changed the philosophy of analytical method development. This book chapter describes the 12 principles of Green Analytical Chemistry and various methodologies for the assessment of the greenness of analytical methods. The three main steps in the analytical method development – sample preparation, separation and detection- are described in a “green perspective”. Special emphasis is given to the description of green sample preparation procedures, in particular to Solid Phase Microextraction, that, since its introduction in 1989 by Janusz Pawliszyn, has drastically revolutionized the methodology of sample preparation, providing a convenient and green alternative to already existing methods.

Facile construction of superhydrophobic hybrids of metal-organic framework grown on nanosheet for high-performance extraction of benzene homologues

Encapsulating functional nanomaterials within the bulk of metal-organic frameworks (MOFs) offers the opportunity to construct high-performance hybrid coating materials for solid phase microextraction (SPME). In this work, we proposed the facile synthesis of a superhydrophobic MOF composite material (_NSZIF-8^Si) by growing ZIF-8 on Mn_xO_y nanosheet (NS) and subsequently depositing short-chain polysiloxane on the surface of the composite. A novel SPME fiber was successfully prepared based on the _NSZIF-8^Si composite. The _NSZIF-8^Si fiber possessed outstanding thermal stability (up to 450 °C). In headspace SPME of BTEX, the home-made fiber exhibited extraction efficiencies much higher than the commercially available PDMS fiber. This phenomenon was due to the synergetic cooperation of the π-π stacking and the hydrophobic interactions between the _NSZIF-8^Si coating and the analyte molecules, as well as the increased aspect ratio of the MOF grown on the nanosheet. The established method achieved wide linearity (5-2000 ng L^-1) and low LODs (0.02 ng L^-1 to 0.21 ng L^-1). Satisfactory recoveries were obtained in the analysis of real water samples collected from the Pearl River, indicative of the good reliability of the established method for real-scenario applications. This work might provide critical insights in constructing novel NS/MOF composite materials for the development of high-performance SPME fiber coatings.

High-throughput quantification of drugs of abuse in biofluids via 96-solid-phase microextraction-transmission mode and direct analysis in real time mass spectrometry

RATIONALE

The workload of clinical laboratories has been steadily increasing over the last few years. High-throughput (HT) sample processing allows scientists to spend more time undertaking matters of critical thinking rather than laborious sample processing. Herein we introduce a HT 96-solid-phase microextraction (SPME) transmission mode (TM) system coupled to direct analysis in real time (DART) mass spectrometry (MS).

METHODS

Model compounds (opioids) were extracted from urine and plasma samples using a 96-SPME-TM device. A standard voltage and pressure (SVP) DART source was used for all experiments. Examination of SPME-TM performance was done using high-resolution mass spectrometry (HRMS) in full scan mode (100-500 m/z), whereas quantitation of opioids was performed using triple quadrupole MS in multiple reaction monitoring mode and by using a matrix-matched internal standard correction method.

RESULTS

Thirteen points (0.5 to 200 ng mL^-1 ) were used to establish a calibration curve. Low limits of quantitation (LOQ) were obtained (0.5 to 25 ng mL^-1 ) for matrices used. Acceptable accuracy (71.4-129.4%) and repeatability (1.1-24%) were obtained for validation levels tested (0.5, 30 and 90 ng mL^-1 ). In less than 1.5 hours, 96 samples were extracted, desorbed and processed using the 96-SPME-TM system coupled to DART-MS.

CONCLUSIONS

A rapid HT method for detection of opioids in urine and plasma samples was developed. This study demonstrated that ambient ionization mass spectrometry coupled to robust sample preparation methods such as SPME-TM can rapidly and efficiently screen/quantify target analytes in a HT context.

Coated direct inlet probe coupled with atmospheric-pressure chemical ionization and high-resolution mass spectrometry for fast quantitation of target analytes

The coated direct inlet probe (CDIP) is a new laboratory-made low-cost technology developed from a direct inlet probe (DIP), which has the advantage of quick enrichment/cleanup of an analyte from liquid samples. A capillary probe is coated with hydroxy-terminated polydimethylsiloxane (OH-PDMS), divinylbenzene (DVB), and β-cyclodextrin (β-CD) by a sol-gel method. This probe can be directly coupled with a commercialized atmospheric-pressure chemical ionization (APCI) ion source and high-resolution mass spectrometry, which are widely applicable, reliable, and durable. The ability to perform quantitative analyses with the use of a stable-isotope-labeled internal standard (SIL-IS) was tested by using different concentrations of acenaphthylene (ACY), acenaphthene (ACP), fluorene (FLR), fluoranthene (FLT), phenanthrene (PHE), and benzo[a]pyrene (B[a]P). Calibration curves with a coefficient of determination of R² ≥ 0.9982 for different polycyclic aromatic hydrocarbons (PAHs) were obtained. A limit of detection (LOD) of 0.008-0.04 ng mL^-1 for PAHs was determined. The entire workflow is solvent-free and can be completed in less than 5 min, which demonstrates the advantages of this technique for quantitative analysis.

Novel SPME fibers based on a plastic support for determination of plasma protein binding of thiosemicarbazone metal chelators: a case example of DpC, an anti-cancer drug that entered clinical trials

Solid-phase microextraction (SPME) is an alternative method to dialysis and ultrafiltration for the determination of plasma protein binding (PPB) of drugs. It is particularly advantageous for complicated analytes where standard methods are not applicable. Di-2-pyridylketone 4-cyclohexyl-4-methyl-3-thiosemicarbazone (DpC) is a lead compound of novel thiosemicarbazone anti-cancer drugs, which entered clinical trials in 2016. However, this agent exhibited non-specific binding on filtration membranes and had intrinsic chelation activity, which precluded standard PPB methods. In this study, using a simple and fast procedure, we prepared novel SPME fibers for extraction of DpC based on a metal-free, silicon string support, covered with C18 sorbent. Reproducibility of the preparation process was demonstrated by the percent relative standard deviation (RSD) of ≤ 9.2% of the amount of DpC extracted from PBS by several independently prepared fibers. The SPME procedure was optimized by evaluating extraction and desorption time profiles. Suitability of the optimized protocol was verified by examining reproducibility, linearity, and recovery of DpC extracted from PBS or plasma. All samples extracted by SPME were analyzed using an optimized and validated UHPLC-MS/MS method. The developed procedure was applied to the in vitro determination of PPB of DpC at two clinically relevant concentrations (500 and 1000 ng/mL). These studies showed that DpC is highly bound to plasma proteins (PPB ≥ 88%) and this did not differ significantly between both concentrations tested. This investigation provides novel data in the applicability of SPME for the determination of PPB of chelators, as well as useful information for the clinical development of DpC. Graphical abstract.

Green sample preparations for the bioanalysis of drugs of abuse in complex matrices

The sample preparation is the most critical step involved in the bioanalytical process. When dealing with green analytical chemistry, sample preparation can be even more challenging. To fit the green analytical chemistry principles, efforts should be made toward the elimination or reduction of the use of toxic reagents and solvents, minimization of energy consumption and increased operator safety. The simplest sample preparations are more appropriate for liquid biological matrices with little interfering compounds such as urine, plasma and oral fluid. The same does not usually occur with complex matrices that require more laborious procedures. The present review discusses green analytical approaches for the analyses of drugs of abuse in complex biological matrices, such as whole blood, breast milk, meconium and hair.

Development and validation of a fully automated solid phase microextraction high throughput method for quantitative analysis of multiresidue veterinary drugs in chicken tissue

This paper presents the development and validation of a fully automated, high-throughput multiclass, multiresidue method for quantitative analysis of 77 veterinary drugs in chicken muscle via direct immersion solid phase microextraction (DI-SPME) and ultra-high pressure liquid chromatography-electrospray ionization - tandem mass spectrometry (UHPLC-ESI-MS/MS). The selected drugs represent more than 12 different classes of drugs characterized by varying physical and chemical properties. A Hydrophilic-lipophilic balance (HLB)/polyacrylonitrile (PAN) extraction phase, prepared using HLB particles synthesized in-house, yielded the best extraction/desorption performance among four different SPME extraction phases evaluated in the current work. The developed SPME method was optimized in terms of SPME coating and geometry, desorption solvent, extraction and rinsing conditions, and extraction and desorption times. Multivariate analysis was performed to determine the optimal desorption solvent for the proposed application. The developed method was validated according to the Food and Drug Administration (FDA) guidelines, taking into account Canadian maximum residue limits (MRLs) and US maximum tolerance levels for veterinary drugs in meat. Method accuracy ranged from 80 to 120% for at least 73 compounds, with relative standard deviation of 1-15%. Inter-day precision ranged from 4 to 15% for 70 compounds. Determination coefficients values were higher than 0.991 for all compounds under study with no significant lack of fit (p > 0.05) at the 5% level. In terms of limits of quantitation, the method was able to meet both Canadian and US regulatory levels for all compounds under study.

Inhibition of water adsorption into polar solid-phase microextraction materials with ultrathin polydimethylsiloxane coating for thermal desorption-gas chromatography analysis

Solid-phase microextraction (SPME) coupled with thermal desorption-gas chromatography (TD-GC) has become a powerful analysis tool for volatile organic compounds (VOCs) and semi-volatile organic compounds (SVOCs) in water samples. However, water adsorption into polar microextraction phase is usually unavoidable during the extraction process, and the burst of large amounts of water vapour during thermal desorption will cause serious problems to GC separation and detectors. Pawliszyn's group had demonstrated that the tens of micron-thick, defect-free polydimethylsiloxane (PDMS) coating could act as a perfect barrier for water adsorption and offer much better compatibility in complex matrices. However, the PDMS overcoat largely decreased the uptake rate of polar analytes into the inner sorbent. In order to quantify the effect of PDMS coating thickness on water adsorption amount and the extraction kinetics, ultrathin PDMS layer was used to coat the polar extraction phase with polyimide (PI) as a model in this work. It was surprising to find that the PDMS coating with the thickness less than one micron can decrease the water adsorption by 96%, while the extraction efficiency for polar analytes (phenolic compounds and nitroaromatic explosives) was decreased by less than 20% at the extraction time of 30 min. Moreover, the kinetic data showed that the thinner the PDMS coating was, the less the uptake rate of polar analytes into PI extraction phase decreased. Finally, polar poly (phthalazine ether sulfone ketone) (PPESK) extraction phase was also coated with ultrathin PDMS coating to verify the universality of the strategy. Generally, the water adsorption problem in polar SPME was overcome to a great extent, and the extraction efficiency of polar analytes was mainly preserved with this ultrathin PDMS coating, which could broaden the application of SPME in the environmental field.

Graphene-based metal and nitrogen-doped carbon composites as adsorbents for highly sensitive solid phase microextraction of polycyclic aromatic hydrocarbons

Herein, a graphene-based metal and nitrogen-doped carbon (GNC-Co) composite, derived from zeolite imidazolate framework-67 (ZIF-67)-graphene oxide composites, was successfully developed and applied as an excellent fiber coating for solid phase microextraction (SPME) with enhanced performance. The fabricated carbon has a hierarchically micro/mesoporous structure with a high specific surface area of 123 m2 g-1. The study found that pyrolytic graphene (G) has good adsorption properties for anthracene, phenanthrene, fluoranthene and pyrene, while pyrolytic ZIF-67 (NC-Co) has good adsorption properties for naphthalene, acenaphthylene, acenaphthylene and fluorene. Combined with the advantage of G and NC-Co, the synthesized composite GNC-Co enabled the integration of the unique properties of these two fascinating materials and proved to show better performance in the extraction of all polycyclic aromatic hydrocarbons (PAHs). Compared to the commercial PDMS fiber, the self-made fiber achieved GC responses about 2-9 times as high as those obtained by the commercial 30 μm PDMS fiber. Furthermore, the self-made fiber obtained low detection limits in the range of 0.01-0.74 ng L-1 and wide linearity under the optimized extraction conditions. Finally, the GNC-Co coated fiber was successfully used for the detection of PAHs in real river water samples, which proved the applicability of the method.

Tissue storage affects lipidome profiling in comparison to in vivo microsampling approach

Low-invasive in vivo solid-phase microextraction (SPME) was used to investigate the lipid profiles of muscle tissue of living fish. Briefly, mixed mode SPME fibers were inserted into the muscle for 20 min extraction, and then the fibers were desorbed in an optimal mixture of solvents. The obtained lipid profile was then compared and contrasted to that obtained with employment of ex vivo SPME and solid-liquid extraction (SLE) from fish muscle tissue belonging to the same group of fish, following a one-year storage period. Ex vivo SPME analysis of stored muscle samples revealed 10-fold decrease in the number of detected molecular features in comparison to in vivo study. Moreover, in vivo microsampling enabled the identification of different classes of bioactive lipids, including fatty acyls, not present in the lipid profile obtained through ex vivo SPME and SLE, suggesting the alterations occurring in the unbound lipid fraction of the system under study during the storage and also indicating the advantage of the in vivo extraction approach.

Coated blade spray: shifting the paradigm of direct sample introduction to MS

Coated blade spray (CBS) is a solid-phase microextraction-based technology that can be directly coupled to MS to enable the rapid qualitative and quantitative analysis of complex matrices. The goal of this mini review is to concisely introduce CBS's operational fundamentals and to consider how it correlates/contrasts with existing direct-to-MS technologies suitable for bioanalytical applications. In addition, we provide a fair comparison of CBS to other existing solid-phase microextraction-to-MS approaches, as well as an overview of recent CBS applications/strategies that have been developed to analyze diverse compounds present in biofluids.

Quantitative analysis of biofluid spots by coated blade spray mass spectrometry, a new approach to rapid screening

This study demonstrates the quantitative capabilities of coated blade spray (CBS) mass spectrometry (MS) for the concomitant analysis of multiple target substances in biofluid spots. In CBS-MS the analytes present in a given sample are first isolated and enriched in the thin coating of the CBS device. After a quick rinsing of the blade surface, as to remove remaining matrix, the analytes are quickly desorbed with the help of a solvent and then directly electrosprayed into the MS analyzer. Diverse pain management drugs, controlled substances, and therapeutic medications were successfully determined using only 10 µL of biofluid, with limits of quantitation in the low/sub ng·mL⁻¹ level attained within 7 minutes.

A flow-through aqueous standard generation system for thin film microextraction investigations of UV filters and biocides partitioning to different environmental compartments

In this paper problems associated with preparation of aqueous standard of highly hydrophobic compounds such as partial precipitation, being lost on the surfaces, low solubility in water and limited sample volume for accurate determination of their distribution coefficients are addressed. The following work presents two approaches that utilize blade thin film microextraction (TFME) to investigate partitioning of UV filters and biocides to humic acid (dissolved organic carbon) and sediment. A steady-state concentration of target analytes in water was generated using a flow-through aqueous standard generation (ASG) system. Dialysis membranes, a polytetrafluoroethylene permeation tube, and a frit porous (0.5 μm) coated by epoxy glue were basic elements used for preparation of the ASG system. In the currently presented study, negligible depletion TFME using hydrophilic-lipophilic balance (HLB) and octadecyl silica-based (C18) sorbents was employed towards the attainment of free concentration values of target analytes in the studied matrices. Thin film geometry provided a large volume of extraction phase, which improved the sensitivity of the method towards highly matrix-bound analytes. Extractions were performed in the equilibrium regime so as to prevent matrix effects and with aims to reach maximum method sensitivity for all analytes under study. Partitioning of analytes on dissolved organic carbon (DOC) was investigated in ASG to facilitate large sample volume conditions. Binding percentages and DOC distribution coefficients (Log K_DOC) ranged from 20 to 98% and 3.71-6.72, respectively. Furthermore, sediment-water partition coefficients (K_d), organic-carbon normalized partition coefficients (Log K_OC), and DOC distribution coefficients (Log K_DOC) were investigated in slurry sediment, and ranged from 33 to 2860, 3.31-5.24 and 4.52-5.75 Lkg^-1, respectively. The obtained results demonstrated that investigations utilizing ASG and TFME can yield reliable binding information for compounds with high log K_OW values. This information is useful for study of fate, transport, and ecotoxicological effects of UV filters and biocides in aquatic environment.

High-Throughput Screening and Quantitation of Target Compounds in Biofluids by Coated Blade Spray-Mass Spectrometry

Most contemporary methods of screening and quantitating controlled substances and therapeutic drugs in biofluids typically require laborious, time-consuming, and expensive analytical workflows. In recent years, our group has worked toward developing microextraction (μe)-mass spectrometry (MS) technologies that merge all of the tedious steps of the classical methods into a simple, efficient, and low-cost methodology. Unquestionably, the automation of these technologies allows for faster sample throughput, greater reproducibility, and radically reduced analysis times. Coated blade spray (CBS) is a μe technology engineered for extracting/enriching analytes of interest in complex matrices, and it can be directly coupled with MS instruments to achieve efficient screening and quantitative analysis. In this study, we introduced CBS as a technology that can be arranged to perform either rapid diagnostics (single vial) or the high-throughput (96-well plate) analysis of biofluids. Furthermore, we demonstrate that performing 96-CBS extractions at the same time allows the total analysis time to be reduced to less than 55 s per sample. Aiming to validate the versatility of CBS, substances comprising a broad range of molecular weights, moieties, protein binding, and polarities were selected. Thus, the high-throughput (HT)-CBS technology was used for the concomitant quantitation of 18 compounds (mixture of anabolics, β-2 agonists, diuretics, stimulants, narcotics, and β-blockers) spiked in human urine and plasma samples. Excellent precision (∼2.5%), accuracy (≥90%), and linearity (R² ≥ 0.99) were attained for all the studied compounds, and the limits of quantitation (LOQs) were within the range of 0.1 to 10 ng·mL^-1 for plasma and 0.25 to 10 ng·mL^-1 for urine. The results reported in this paper confirm CBS's great potential for achieving subsixty-second analyses of target compounds in a broad range of fields such as those related to clinical diagnosis, food, the environment, and forensics.