Variations of Flame Retardant, Polycyclic Aromatic Hydrocarbon, and Pesticide Concentrations in Chicago's Atmosphere Measured using Passive Sampling

Archetypes of Spatial Concentration Variability of Organic Contaminants in the Atmosphere: Implications for Identifying Sources and Mapping the Gaseous Outdoor Inhalation Exposome

Whereas inhalation exposure to organic contaminants can negatively impact human health, knowledge of their spatial variability in the ambient atmosphere remains limited. We analyzed the extracts of passive air samplers deployed at 119 unique sites in Southern Canada between 2019 and 2022 for 353 organic vapors. Hierarchical clustering of the obtained data set revealed four archetypes of spatial concentration variability in the outdoor atmosphere, which are indicative of common sources and similar atmospheric dispersion behavior. "Point Source" signatures are characterized by elevated concentration in the vicinity of major release locations. A "Population" signature applies to compounds whose air concentrations are highly correlated with population density, and is associated with emissions from consumer products. The "Water Source" signature applies to substances with elevated levels in the vicinity of water bodies from which they evaporate. Another group of compounds displays a "Uniform" signature, indicative of a lack of major sources within the study area. We illustrate how such a data set, and the derived spatial patterns, can be applied to support the identification of sources, the quantification of atmospheric emissions, the modeling of air quality, and the investigation of potential inequities in inhalation exposure.

Assessing pesticides in the atmosphere: A global study on pollution, human health effects, monitoring network and regulatory performance

Pesticides are widely used in agriculture, but their impact on the environment and human health is a major concern. While much attention has been given to their presence in soil, water, and food, there have been few studies on airborne pesticide pollution on a global scale. This study aimed to assess the extent of atmospheric pesticide pollution in countries worldwide and identify regional differences using a scoring approach. In addition to analyzing the health risks associated with pesticide pollution, we also examined agricultural practices and current air quality standards for pesticides in these countries. The pollution scores varied significantly among the countries, particularly in Europe. Asian and Oceanic countries generally had higher scores compared to those in the Americas, suggesting a relatively higher level of air pollution caused by pesticides in these regions. It is worth noting that the current pollution levels, as assessed theoretically, pose minimal health risks to humans. However, studies in the literature have shown that excessive exposure to pesticides present in the atmosphere has been associated with various health problems, such as cancer, neuropsychiatric disorders, and other chronic diseases. Interestingly, European countries had the highest overall pesticide application intensities, but this did not necessarily correspond to higher atmospheric pesticide pollution scores. Only a few countries have established air quality standards specifically for pesticides. Furthermore, pollution scores across states in the USA were investigated and the global sampling sites were mapped. The findings revealed that the scores varied widely in the USA and the current sampling sites were limited or unevenly distributed in some countries, particularly the Nordic countries. These findings can help global relevant environmental agencies to set up comprehensive monitoring networks. Overall, the present research highlights the need to create a pesticide monitoring system and increase efforts to enhance pesticide regulation, ensure consistency in standards, and promote international cooperation.

Diffusive fluxes of persistent organic pollutants between Arctic atmosphere, surface waters and sediments

Arctic communities are disproportionately exposed to pollutants from sources including global atmospheric transport and formerly used defense sites (FUDS). The effects of climate change and increasing development in the Arctic have the potential to exacerbate this problem. Yupik People of Sivuqaq, or St Lawrence Island, Alaska are one such community with documented exposures to pollutants from FUDS, and their traditional lipid-rich foods such as blubber and rendered oils of marine mammals. Troutman Lake, adjacent to the Yupik community of Gambell, Alaska, was used as a disposal site during the decommission of the adjacent FUDS, leading to community concern about exposure to military pollution and intrusion from historic local dump sites. In collaboration with a local community group, this study utilized passive sampling devices deployed in Troutman Lake. Air, water and sediment deployed samplers were analyzed for unsubstituted and alkylated polycyclic aromatic hydrocarbons (PAHs), brominated and organophosphate flame retardants and polychlorinated biphenyls (PCBs). PAH concentrations were low and comparable to other remote/rural locations. PAHs were generally in deposition from the overlying atmosphere into Troutman Lake. Of the flame retardants, brominated diphenyl ether-47 was detected in all surface water samplers while triphenyl phosphate was detected in all environmental compartments. Both were at concentrations equivalent or lower than other remote locations. Of particular interest, we measured higher atmospheric concentrations of tris(2-chloroethyl) phosphate (TCEP) (0.75-2.8 ng/m3) than previously reported in the literature for remote Arctic sites (<0.017-0.56 ng/m3). TCEP was found to be in deposition to Troutman Lake at magnitudes from 290 to 1300 ng/m2/day. No PCBs were detected in this study. Our findings demonstrate the relevance of both modern and legacy chemicals from local and global sources. These results help us to understand the fate of anthropogenic contaminants in dynamic Arctic systems providing valuable data for communities, policy makers and scientists.

High spatial resolution measurements of passive-sampler derived air concentrations of persistent organic pollutants in the Campania region, Italy: Implications for source identification and risk analysis

Because most relevant studies have used small sample sizes, to date, representative atmospheric monitoring of persistent organic pollutants (POPs) on a regional scale has been very limited, which makes it difficult to precisely identify "hotspots" and possible pollution sources. In this study, an ultrahigh resolution monitoring technique was used to measure the atmospheric spatial variations in POP concentrations on a regional scale, throughout Campania, Italy. The occurrence of specific POPs-including polychlorinated biphenyls (PCBs), organochlorine pesticides (OCPs), polycyclic aromatic hydrocarbons (PAHs), polybrominated diphenyl ethers (PBDEs) and phthalate esters (PAEs)-were investigated using polyurethane foam-based passive air samplers (PUF-PAS), which were deployed at 129 sites across the Campania Territory between April and July 2016. The results show that the highest POP levels occurred in the Naples metropolitan area (NMA), although there were other problematic spots throughout the Territory. More specifically, hotspot areas in the NMA that depict serious POP pollution were found in the Bagnoli brownfield site, Sarno River Basin, and parts of the northeastern NMA sector. The atmospheric POP contamination in Campania is jointly controlled by the contributions of local emissions and long-range atmospheric transport. Diffusion model was employed to identify the potential sources of various POPs. The simulation showed that all the POP sources are located in the NMA and are closely related to industrial sites. This study demonstrates the advantage of using large sample sizes to identify POP source locations and achieve geospatial visualization of POP concentration and risk assessment levels.

Using diagnostic ratios to characterize sources of polycyclic aromatic hydrocarbons in the Great Lakes atmosphere

The present study characterized source profiles of polycyclic aromatic hydrocarbons (PAHs) for the Great Lakes atmosphere using nine PAH diagnostic ratios (DRs). The samples were collected from six sites in the Great Lakes basin during 1996-2018 within the Integrated Atmospheric Deposition Network (IADN). In general, pyrogenic sources, including coal combustion and vehicular emissions, were the most important contributors to atmospheric profiles, in particular at the urban sites. Diesel emissions accounted for a larger portion of the traffic-originated PAHs than gasoline emissions at all sites, but this compositional pattern was less obvious at the urban sites. Temporal analyses for DRs revealed that the relative contribution of petrogenic sources and volatilization from surfaces has been increasing gradually, and that the gaps in PAH emissions between diesel- and gasoline-engines appeared to be further amplified in recent years. Coal combustion and non-pyrogenic emissions were the main PAH sources for winter and summer air, respectively, but none of the DRs responded to these changes. DRs were generally different between vapor and particle phases. Our findings shed light on spatial and temporal trends of PAH DRs and PAH source characterization in the Great Lakes basin. Additionally, this study confirmed the usefulness of DRs, especially when combined with the PMF analysis, while also highlighting the limitation of multiple DRs.

GAPS-megacities: A new global platform for investigating persistent organic pollutants and chemicals of emerging concern in urban air

A pilot study was initiated in 2018 under the Global Atmospheric Passive Sampling (GAPS) Network named GAPS-Megacities. This study included 20 megacities/major cities across the globe with the goal of better understanding and comparing ambient air levels of persistent organic pollutants and other chemicals of emerging concern, to which humans residing in large cities are exposed. The first results from the initial period of sampling are reported for 19 cities for several classes of flame retardants (FRs) including organophosphate esters (OPEs), polybrominated diphenyl ethers (PBDEs), and halogenated flame retardants (HFRs) including new flame retardants (NFRs), tetrabromobisphenol A (TBBPA) and hexabromocyclododecane (HBCDD). The two cities, New York (USA) and London (UK) stood out with ∼3.5 to 30 times higher total FR concentrations as compared to other major cities, with total concentrations of OPEs of 15,100 and 14,100 pg/m³, respectively. Atmospheric concentrations of OPEs significantly dominated the FR profile at all sites, with total concentrations in air that were 2-5 orders of magnitude higher compared to other targeted chemical classes. A moderately strong and significant correlation (r = 0.625, p < 0.001) was observed for Gross Domestic Product index of the cities with total OPEs levels. Although large differences in FR levels were observed between some cities, when averaged across the five United Nations regions, the FR classes were more evenly distributed and varied by less than a factor of five. Results for Toronto, which is a 'reference city' for this study, agreed well with a more in-depth investigation of the level of FRs over different seasons and across eight sites representing different urban source sectors (e.g. traffic, industrial, residential and background). Future sampling periods under this project will investigate trace metals and other contaminant classes, linkages to toxicology, non-targeted analysis, and eventually temporal trends. The study provides a unique urban platform for evaluating global exposome.

Passive air sampling for semi-volatile organic chemicals

During passive air sampling, the amount of a chemical taken up in a sorbent from the air without the help of a pump is quantified and converted into an air concentration. In an equilibrium sampler, this conversion requires a thermodynamic parameter, the equilibrium sorption coefficient between gas-phase and sorbent. In a kinetic sampler, a time-averaged air concentration is obtained using a sampling rate, which is a kinetic parameter. Design requirements for kinetic and equilibrium sampling conflict with each other. The volatility of semi-volatile organic compounds (SVOCs) varies over five orders of magnitude, which implies that passive air samplers are inevitably kinetic samplers for less volatile SVOCs and equilibrium samplers for more volatile SVOCs. Therefore, most currently used passive sampler designs for SVOCs are a compromise that requires the consideration of both a thermodynamic and a kinetic parameter. Their quantitative interpretation depends on assumptions that are rarely fulfilled, and on input parameters, that are often only known with high uncertainty. Kinetic passive air sampling for SVOCs is also challenging because their typically very low atmospheric concentrations necessitate relatively high sampling rates that can only be achieved without the use of diffusive barriers. This in turn renders sampling rates dependent on wind conditions and therefore highly variable. Despite the overall high uncertainty arising from these challenges, passive air samplers for SVOCs have valuable roles to play in recording (i) spatial concentration variability at scales ranging from a few centimeters to tens of thousands of kilometers, (ii) long-term trends, (iii) air contamination in remote and inaccessible locations and (iv) indoor inhalation exposure. Going forward, thermal desorption of sorbents may lower the detection limits for some SVOCs to an extent that the use of diffusive barriers in the kinetic sampling of SVOCs becomes feasible, which is a prerequisite to decreasing the uncertainty of sampling rates. If the thermally stable sorbent additionally has a high sorptive capacity, it may be possible to design true kinetic samplers for most SVOCs. In the meantime, the passive air sampling community would benefit from being more transparent by rigorously quantifying and explicitly reporting uncertainty.

Determination of dry deposition velocity of polycyclic aromatic hydrocarbons under the sub-tropical climate and its implication for regional cycling

Atmospheric dry deposition is a major pathway for removal of polycyclic aromatic hydrocarbons (PAHs) from the atmosphere. Despite its significance in the atmospheric environment, measurements of the dry deposition velocity (V_DD) and deposition fluxes (F_DD) of PAHs are relatively limited. In this study, a passive dry deposition (PAS-DD) collector was co-deployed with passive air sampler polyurethane foam (PAS-PUF) from November 2015 to November 2016 in two major cities (Kathmandu and Pokhara), Nepal, to investigate the V_DD and F_DD of PAHs. The V_DD of PAHs ranged from 0.25 to 0.5 cm s^-1 and the annual average was recorded as 0.37 ± 0.08 cm s^-1. On the basis of measured V_DD, the F_DD of ∑15PAHs in Kathmandu and Pokhara were estimated as 66 and 5 kg yr^-1 respectively. According to the measured V_DD of Kathmandu and Pokhara in this study, and the previously published V_DD data of Toronto, Canada, where the same PAS-DD collector was used, a significant multi-linear correlation (r² = 0.79, p < 0.05) was found between V_DD of higher molecular weight (HMW with MW ≥ 228.3 and ≥ 4 rings) PAHs and meteorological parameters (precipitation and wind speed) and vapor pressure of PAHs. To the best of our knowledge, this enabled the development of an empirical model that can exhibit the combined effects of meteorological conditions on the V_DD of HMW PAHs. The model was used to estimate the V_DD values for major cities in the Indo-Gangetic Plain (IGP) region and the maximum estimated proportion of HMW PAHs deposited by dry deposition reached up to 60% of total emissions. Although PAH emissions in the IGP region pose global risks, the results of this study highlight the considerable risk for local IGP residents, due to the large dry deposition proportion of HMW PAHs.

Association between Thyroid Function and Exposures to Brominated and Organophosphate Flame Retardants in Rural Central Appalachia

Exposure to flame retardants (FRs) is associated with adverse effects on human health. Focusing on three FR groups, including polybrominated diphenyl ethers (PBDEs), organophosphate FRs (OPFRs), and novel brominated FRs (nBFRs), we determined the levels of these chemicals in indoor air in homes in rural Central Appalachia using passive air samplers and personal exposures in the residents of these homes using silicone wristbands. We also investigated the relationships between the FR levels in wristbands and the thyroid function. The median total concentrations of PBDEs, OPFRs, and nBFRs were 210, 25 000, and 69 pg/m³ in indoor air, and 49, 670, and 110 ng/g in wristbands, respectively. The most abundant chemicals in both air and wristbands were BDE-47 and -99 among PBDEs, tris[(2R)-1-chloro-2-propyl] phosphate among OPFRs, and 2-ethylhexyl 2,3,4,5-tetrabromobenzoate and bis(2-ethylhexyl) tetrabromophthalate among nBFRs. In gender-specific regression models that were controlled for age and smoking, significant associations were observed between BDE-99, BDE-197, and 2-ethylhexyldiphenyl phosphate (EHDP) and free thyroxine (FT₄), between BDE-100 and free triiodothyronine (FT₃), and between anti-Dechlorane Plus (DP) and thyroid-stimulating hormone (TSH). In particular, most penta-BDE congeners were significantly or marginally significantly associated with FT₄ and FT₃ for both females and males. Our results suggest that wristbands can be used as suitable exposure monitors for evaluating human exposure to FRs.

Atmospheric Occurrence of Legacy Pesticides, Current Use Pesticides, and Flame Retardants in and around Protected Areas in Costa Rica and Uganda

Protected areas have developed alongside intensive changes in land use and human settlements in the neighboring landscape. Here, we investigated the occurrence of 21 organochlorine pesticides (OCPs), 14 current use pesticides (CUPs), 47 halogenated flame retardants (HFRs), and 19 organophosphate esters (OPEs) in air around Las Cruces (LC) and La Selva (LS) Biological Stations, Costa Rica, and Kibale National Park (KNP), Uganda using passive air samplers (PAS) with polyurethane foam (PUF) discs (PAS-PUF). Significantly higher concentrations of CUPs were observed around LS, while LC had a higher concentration of OCPs. Land use analysis indicated that LS had a higher fraction of agriculture than LC (33% vs 14%), suggesting the higher CUPs concentration at LS was related to pesticide intensive crops, while higher OCPs concentration at LC may be attributed to the area's long agricultural history characterized by small-scale subsistence farming or long-range transport. In Uganda, CUPs and OCPs were generally lower than in Costa Rica, but high concentrations of HFRs were observed inside KNP, possibly due to human activity at research camps near the protected forest. This is the first study that documented the occurrence of anthropogenic chemicals in the air at protected areas with tropical forests.

Aryl hydrocarbon receptor-mediated activity of gas-phase ambient air derived from passive sampling and an in vitro bioassay

The gaseous fraction of hydrophobic organic contaminants (HOCs) in ambient air appears to be responsible for a significant portion of aryl hydrocarbon receptor (AhR)-mediated activity, but the majority of compounds contributing to this activity remain unidentified. The present study investigated the use of polyethylene passive samplers to isolate gaseous HOCs from ambient air for use in in vitro bioassays and to improve our understanding of the toxicological relevance of the gaseous fraction of ambient air in urban and residential environments. Concentrations of polycyclic aromatic hydrocarbons (PAHs) and organic flame retardants were measured in polyethylene passive sampler extracts. Extracts were also analyzed using an in vitro bioassay to measure AhR-mediated activity. Bioassay-derived benzo[a]pyrene (BaP) equivalents (BaP-Eq_bio ), a measure of potency of HOC mixtures, were greatest in the downtown Cleveland area and lowest at rural/residential sites further from the city center. The BaP-Eq_bio was weakly correlated with concentrations of 2-ring alkyl/substituted PAHs and one organophosphate flame retardant, ethylhexyl diphenyl phosphate. Potency predicted based on literature-derived induction equivalency factors (IEFs) explained only 2 to 23% of the AhR-mediated potency observed in bioassay experiments. Our results suggests that health risks of gaseous ambient air pollution predicted using data from targeted chemical analysis may underestimate risks of exposure, most likely due to augmentation of potency by unmonitored chemicals in the mixture, and the lack of relevant IEFs for many targeted analytes. Environ Toxicol Chem 2019;38:748-759. © 2019 SETAC.

Analysis of brominated and chlorinated flame retardants, organophosphate esters, and polycyclic aromatic hydrocarbons in silicone wristbands used as personal passive samplers

For the first time, we present an analytical method to simultaneously extract, fractionate, and quantify four groups of semi-volatile organic compounds (SVOCs) in silicone wristbands, including 35 polybrominated diphenyl ethers (PBDEs), 10 novel flame retardants (NFRs), 19 organophosphate esters (OPEs), and 13 polycyclic aromatic hydrocarbons (PAHs). Wristbands were extracted using ultrasonication, and cleaned and fractionated on two multi-layer columns: one consisting of neutral alumina, neutral silica and Florisil, and the other consisting of neutral alumina, neutral silica, and acidic silica. Method accuracy and precision were validated using spiked wristband samples (n = 8) and procedural blanks (n = 7). Average matrix spike percent recoveries for all target analytes were within 57-107% with relative standard errors < 20%, with a few exceptions. This method was applied to analyze thirteen wristbands worn by ten participants for seven days; three participants wore two wristbands to evaluate duplicate samples. Percent recoveries of surrogate standards for all four groups of analytes in these wristbands were all within the 80-120% range with a few exceptions: recoveries for ¹³C₁₂BDE-209 and for ¹³C₁₂-triphenyl phosphate ranged from 35 to 62% and 69-176%, respectively. The majority of target analytes were detected in at least half of worn wristbands. The levels of total PBDEs, NFRs, OPEs and PAHs in deployed wristbands ranged from 28.4 to 412 ng, 40.7 to 625 ng, 2440 to 9580 ng, and 76.2 to 1240 ng, respectively.

Polycyclic aromatic hydrocarbons in the urban atmosphere of Nepal: Distribution, sources, seasonal trends, and cancer risk

Atmospheric polycyclic aromatic hydrocarbons (PAHs) in urban areas have always been a global concern, as these areas are considered to be the source region. Despite studies on the concentrations of PAHs in water, soils and sediments, knowledge of the distribution patterns, seasonality and sources of PAHs in urban areas of Nepal remains limited. In this study, polyurethane foam passive air samplers were used to measure gas-phase PAH concentrations over different land types in three major cities of Nepal-namely, Kathmandu (the capital) and Pokhara (both densely populated cities), and Hetauda (an agricultural city). The average concentrations of ∑15PAHs in ng/m³ were 16.1±7.0 (6.4-28.6), 14.1±6.2 (6.8-29.4) and 11.1±9.0 (4.1-38.0) in Kathmandu, Pokhara and Hetauda, respectively. Molecular diagnostic ratio analysis suggested that fossil fuel combustion was a common PAH source for all three cities. In addition to this, coal combustion in Kathmandu, vehicle emissions in Pokhara, and grass/wood combustion in Hetauda were also possible sources of PAHs. In terms of cancer risk from PAH inhalation, a religious site with intense incense burning, a brick production area where extensive coal combustion is common, and a market place with heavy traffic emission, were associated with a higher risk than other areas. There were no clear seasonal trends in atmospheric PAHs. The estimated cancer risk due to inhalation of gas-phase PAHs exceeded the USEPA standard at >90% of the sites.

Calibration and evaluation of PUF-PAS sampling rates across the Global Atmospheric Passive Sampling (GAPS) network

Passive air samplers equipped with polyurethane foam (PUF-PAS) are frequently used to measure persistent organic pollutants (POPs) in ambient air. Here we present and evaluate a method to determine sampling rates (R_S), and the effective sampling volume (V_eff), for gas-phase chemical compounds captured by a PUF-PAS sampler deployed anywhere in the world. The method uses a mathematical model that requires only publicly available hourly meteorological data, physical-chemical properties of the target compound, and the deployment dates. The predicted R_S is calibrated from sampling rates determined from 5 depuration compounds (¹³C PCB-9, ¹³C PCB-15, ¹³C PCB-32, PCB-30, and d₆-γ-HCH) injected in 82 samples from 24 sites deployed by the Global Atmospheric Passive Sampling (GAPS) network around the world. The dimensionless fitting parameter, gamma, was found to be constant at 0.267 when implementing the Integrated Surface Database (ISD) weather observations and 0.315 using the Modern Era Retrospective-Analysis for Research and Applications (MERRA) weather dataset. The model provided acceptable agreement between modelled and depuration determined sampling rates, with ¹³C PCB-9, ¹³C PCB-32, and d₆-γ-HCH having mean percent bias near zero (±6%) for both weather datasets (ISD and MERRA). The model provides inexpensive and reliable PUF-PAS gas-phase R_S and V_eff when depuration compounds produce unusual or suspect results and for sites where the use of depuration compounds is impractical, such as sites experiencing low average wind speeds, very cold temperatures, or remote locations.

New insight into the distribution pattern, levels, and risk diagnosis of FRs in indoor and outdoor air at low- and high-altitude zones of Pakistan: Implications for sources and exposure

Data regarding flame retardants (FRs) in indoor and outdoor air and their exposure to population are scarce and especially unknown in the case of Pakistan. The current study was designed to probe FR concentrations and distribution pattern in indoor and outdoor air at different altitudinal zones (DAZs) of Pakistan with special emphasis on their risk to the exposed population. In this study, passive air samplers for the purpose of FR deposition were deployed in indoor and outdoor air at the industrial, rural, and background/colder zones/sites. All the indoor and outdoor air samples collected from DAZs were analyzed for the target FRs (9.30-472.30 pg/m³), showing a decreasing trend as follows: ∑NBFRs > ∑PBDEs > ∑DP. However, significant correlations among FRs in the indoor and outdoor air at DAZs signified a similar source of FR origin that is used in different consumer goods. Furthermore, air mass trajectories revealed that movement of air over industrial area sources influenced concentrations of FRs at rural sites. The FR concentrations, estimated daily intake (EDI) and the hazard quotient (HQ), were recorded to be higher in toddlers than those in adults. In addition, indoor air samples showed higher FR levels, EDI and HQ, than outdoor air samples. An elevated FR concentrations and their prevalent exposure risks were recorded in the industrial zones followed by rural and background zones. The HQ for BDE-47 and BDE-99 in the indoor and outdoor air samples at different industrial and rural sites were recorded to be >1 in toddlers and adults, this further warrants a health risk in the population. However, FR investigation in indoor and outdoor air samples will provide a baseline data in Pakistan to take further steps by the government and agencies for its implementations.

Release of Airborne Polychlorinated Biphenyls from New Bedford Harbor Results in Elevated Concentrations in the Surrounding Air

Qualitatively and quantitatively, we have demonstrated that airborne polychlorinated biphenyl (PCB) concentrations in the air surrounding New Bedford Harbor (NBH) are caused by its water PCB emissions. We measured airborne PCBs at 18 homes and businesses near NBH in 2015, with values ranging from 0.4 to 38 ng m^-3, with a very strong Aroclor 1242/1016 signal that is most pronounced closest to the harbor and reproducible over three sampling rounds. Using U.S. Environmental Protection Agency (U.S. EPA) water PCB data from 2015 and local meteorology, we predicted gas-phase fluxes of PCBs from 160 to 1200 μg m^-2 day^-1. Fluxes were used as emissions for AERMOD, a widely applied U.S. EPA atmospheric dispersion model, to predict airborne PCB concentrations. The AERMOD predictions were within a factor of 2 of the field measurements. PCB emission from NBH (110 kg year^-1, average 2015) is the largest reported source of airborne PCBs from natural waters in North America, and the source of high ambient air PCB concentrations in locations close to NBH. It is likely that NBH has been an important source of airborne PCBs since it was contaminated with Aroclors more than 60 years ago.

Combined effect of tris(2-chloroethyl)phosphate and benzo (a) pyrene on the release of IL-6 and IL-8 from HepG2 cells via the EGFR-ERK1/2 signaling pathway

Tris(2-chloroethyl)phosphate plus benzo (a) pyrene induced inflammatory response in HepG2 cells through the activation of EGFR-ERK1/2 signaling pathway.

Using long-term air monitoring of semi-volatile organic compounds to evaluate the uncertainty in polyurethane-disk passive sampler-derived air concentrations

Much effort has been made to standardise sampling procedures, laboratory analysis, data analysis, etc. for semi volatile organic contaminants (SVOCs). Yet there are some unresolved issues in regards to comparing measurements from one of the most commonly used passive samplers (PAS), the polyurethane foam (PUF) disk PAS (PUF-PAS), between monitoring networks or different studies. One such issue is that there is no universal means to derive a sampling rate (R_s) or to calculate air concentrations (C_air) from PUF-PAS measurements for SVOCs. C_air was calculated from PUF-PAS measurements from a long-term monitoring program at a site in central Europe applying current understanding of passive sampling theory coupled with a consideration for the sampling of particle associated compounds. C_air were assessed against concurrent active air sampler (AAS) measurements. Use of "site-based/sampler-specific" variables: R_s, calculated using a site calibration, provided similar results for most gas-phase SVOCs to air concentrations derived using "default" values (commonly accepted R_s). Individual monthly PUF-PAS-derived air concentrations for the majority of the target compounds were significantly different (Wilcoxon signed-rank (WSR) test; p < 0.05) to AAS regardless of the input values (site/sampler based or default) used to calculate them. However, annual average PUF-PAS-derived air concentrations were within the same order of magnitude as AAS measurements except for the particle-phase polycyclic aromatic hydrocarbons (PAHs). Underestimation of PUF-derived air concentrations for particle-phase PAHs was attributed to a potential overestimation of the particle infiltration into the PUF-PAS chamber and underestimation of the particle bound fraction of PAHs.

Emerging and Legacy Flame Retardants in UK Indoor Air and Dust: Evidence for Replacement of PBDEs by Emerging Flame Retardants?

Concentrations of 27 emerging (EFRs) and legacy flame retardants (LFRs) were measured in samples of indoor air (n = 35) and indoor dust (n = 77) from UK homes and offices. All target compounds were detected in indoor air and dust samples. Relatively volatile EFRs (e.g., tetrabromoethylcyclohexane-DBE-DBCH) were more frequently detected in indoor air (detection frequencies >60%), while less volatile EFRs (e.g., tetrabromobisphenolA-bis(2,3-dibromopropyl ether (TBBPA-BDBPE) and decabromodiphenyl ethane (DBDPE)) were predominant in dust. Concentrations of some EFRs (e.g., DBDPE) exceeded significantly those reported previously in UK dust (p < 0.05), while concentrations of BDE-209 in office dust were significantly lower (p < 0.05) than those reported previously in UK offices, consistent with the application of DBDPE as an alternative to the Deca-BDE formulation, of which BDE-209 is the principal constituent. Moreover, concentrations of BDEs-47 and -99 (both major constituents of the Penta-BDE product) in office air were significantly lower (p < 0.05) than those in previous UK studies. Our results constitute important early evidence that restrictions on PBDEs have increased demand for EFRs in the UK, with the result that human exposure to PBDEs in UK homes and offices has decreased while exposure to EFRs has risen.

Ten years after entry into force of the Stockholm Convention: What do air monitoring data tell about its effectiveness?

More than a decade ago, the Stockholm Convention on Persistent Organic Pollutants (POPs), one of the multilateral environmental agreements administered by the United Nations Environment Programme (UNEP), entered into force. The objective of this Convention is to protect human health and the environment by controlling the releases of POPs. According to its Article 16, the effectiveness of the Stockholm Convention shall be evaluated using comparable monitoring data on the presence of POPs as well as their regional and global environmental transport. Here, we present a time series analysis on atmospheric POP concentrations from 15 monitoring stations in North America and Europe that provide long-term data and have started operations between 1990 and 2003. We systematically searched for temporal trends and significant structural changes in temporal trends that might result from the provisions of the Stockholm Convention. We find that such structural changes do occur, but they are related mostly to effects of national regulations enforced prior to the implementation of the Stockholm Convention, rather than to the enforcement of the provisions laid out in the Convention. One example is that concentrations of polychlorinated biphenyls, many of which started to decrease rapidly during the 1990s. Also effects of chemical transport and fate, for instance the re-volatilization of POPs from secondary sources, are thought to be a cause of some of the observed structural changes. We conclude that a decade of air monitoring data has not been sufficient for detecting general and statistically significant effects of the Stockholm Convention. Based on these lessons, we present recommendations for the future operation of existing monitoring programs and advocate for a stricter enforcement of the provisions of the Stockholm Convention, in the current absence of proof for its effectiveness.

Spatial Distribution and Air-Water Exchange of Organic Flame Retardants in the Lower Great Lakes

Organic flame retardants (OFRs) such as polybrominated diphenyl ethers (PBDEs) and novel halogenated flame retardants (NHFRs) are ubiquitous, persistent, and bioaccumulative contaminants that have been used in consumer goods to slow combustion. In this study, polyethylene passive samplers (PEs) were deployed throughout the lower Great Lakes (Lake Erie and Lake Ontario) to measure OFRs in air and water, calculate air-water exchange fluxes, and investigate spatial trends. Dissolved Σ12BDE was greatest in Lake Ontario near Toronto (18 pg/L), whereas gaseous Σ12BDE was greatest on the southern shoreline of Lake Erie (11 pg/m(3)). NHFRs were generally below detection limits. Air-water exchange was dominated by absorption of BDEs 47 and 99, ranging from -964 pg/m(2)/day to -30 pg/m(2)/day. Σ12BDE in air and water was significantly correlated with surrounding population density, suggesting that phased-out PBDEs continued to be emitted from population centers along the Great Lakes shoreline in 2012. Correlation with dissolved Σ12BDE was strongest when considering population within 25 km while correlation with gaseous Σ12BDE was strongest when using population within 3 km to the south of each site. Bayesian kriging was used to predict dissolved Σ12BDE over the lakes, illustrating the utility of relatively highly spatially resolved measurements in identifying potential hot spots for future study.

Brominated flame retardants in the indoor environment - Comparative study of indoor contamination from three countries

Concentrations of more than 20 brominated flame retardants (FRs), including polybrominated diphenyl ethers (PBDEs) and emerging FRs, were measured in air, dust and window wipes from 63 homes in Canada, the Czech Republic and the United States in the spring and summer of 2013. Among the PBDEs, the highest concentrations were generally BDE-209 in all three matrices, followed by Penta-BDEs. Among alternative FRs, EHTBB and BEHTBP were detected at the highest concentrations. DBDPE was also a major alternative FR detected in dust and air. Bromobenzenes were detected at lower levels than PBDEs and other alternative FRs; among the bromobenzenes, HBB and PBEB were the most abundant compounds. In general, FR levels were highest in the US and lowest in the Czech Republic - a geographic trend that reflects the flame retardants' market. No statistically significant differences were detected between bedroom and living room FR concentrations in the same house (n=10), suggesting that sources of FRs are widespread indoors and mixing between rooms. The concentrations of FRs in air, dust, and window film were significantly correlated, especially for PBDEs. We found a significant relationship between the concentrations in dust and window film and in the gas phase for FRs with log KOA values <14, suggesting that equilibrium was reached for these but not compounds with log KOA values >14. This hypothesis was confirmed by a large discrepancy between values predicted using a partitioning model and the measured values for FRs with log KOA values >14.

A Model Using Local Weather Data to Determine the Effective Sampling Volume for PCB Congeners Collected on Passive Air Samplers

We have developed and evaluated a mathematical model to determine the effective sampling volumes (Veff) of PCBs and similar compounds captured using polyurethane foam passive air samplers (PUF-PAS). We account for the variability in wind speed, air temperature, and equilibrium partitioning over the course of the deployment of the samplers. The model, provided as an annotated Matlab script, predicts the Veff as a function of physical-chemical properties of each compound and meteorology from the closest Integrated Surface Database (ISD) data set obtained through NOAA's National Centers for Environmental Information (NCEI). The model was developed to be user-friendly, only requiring basic Matlab knowledge. To illustrate the effectiveness of the model, we evaluated three independent data sets of airborne PCBs simultaneously collected using passive and active samplers: at sites in Chicago, Lancaster, UK, and Toronto, Canada. The model provides Veff values comparable to those using depuration compounds and calibration against active samplers, yielding an average congener specific concentration method ratio (active/passive) of 1.1 ± 1.2. We applied the model to PUF-PAS samples collected in Chicago and show that previous methods can underestimate concentrations of PCBs by up to 40%, especially for long deployments, deployments conducted under warming conditions, and compounds with log Koa values less than 8.

Gaseous and Freely-Dissolved PCBs in the Lower Great Lakes Based on Passive Sampling: Spatial Trends and Air-Water Exchange

Polyethylene passive sampling was performed to quantify gaseous and freely dissolved polychlorinated biphenyls (PCBs) in the air and water of Lakes Erie and Ontario during 2011-2012. In view of differing physical characteristics and the impacts of historical contamination by PCBs within these lakes, spatial variation of PCB concentrations and air-water exchange across these lakes may be expected. Both lakes displayed statistically similar aqueous and atmospheric PCB concentrations. Total aqueous concentrations of 29 PCBs ranged from 1.5 pg L(-1) in the open lake of Lake Erie (site E02) in 2011 spring to 105 pg L(-1) in Niagara (site On05) in 2012 summer, while total atmospheric concentrations were 7.7-634 pg m(-3) across both lakes. A west-to-east gradient was observed for aqueous PCBs in Lake Erie. River discharge and localized influences (e.g., sediment resuspension and regional alongshore transport) likely dominated spatial trends of aqueous PCBs in both lakes. Air-water exchange fluxes of Σ7PCBs ranged from -2.4 (±1.9) ng m(-2) day(-1) (deposition) in Sheffield (site E03) to 9.0 (±3.1) ng m(-2) day(-1) (volatilization) in Niagara (site On05). Net volatilization of PCBs was the primary trend across most sites and periods. Almost half of variation in air-water exchange fluxes was attributed to the difference in aqueous concentrations of PCBs. Uncertainty analysis in fugacity ratios and mass fluxes in air-water exchange of PCBs indicated that PCBs have reached or approached equilibrium only at the eastern Lake Erie and along the Canadian shore of Lake Ontario sites, where air-water exchange fluxes dominated atmospheric concentrations.

Seasonality in polybrominated diphenyl ether concentrations in the atmosphere of the Yangtze River Delta, China

Polybrominated diphenyl ether (PBDE) concentrations in the atmosphere in rapidly developing parts of China have been studied little. In this study, polyurethane foam disk passive air samplers were used to comprehensively investigate PBDE concentrations in the atmosphere of the Yangtze River Delta in different seasons in 2010 and 2011. The mean sum of the concentrations of 13 PBDE congeners was 3.3 pg/m(3) in spring, 7.3 pg/m(3) in summer, 1.0 pg/m(3) in autumn, and 12 pg/m(3) in winter. Higher PBDE concentrations were found in urban areas than in rural areas. The PBDE concentrations were comparable to concentrations that have been found in cities around the world. BDE28, BDE47, BDE99, BDE153, and BDE183 were the dominant PBDE congeners in all seasons. High PBDE concentrations were found in satellite cities, such as Changshu, Wujiang, and Zhangjiagang, suggesting that commercial PBDEs (including pentabromodiphenyl ether products) are produced and/or used in those cities. The PBDE concentrations in the atmosphere were used to estimate daily doses through the inhalation of outdoor air. The most severe risks posed by exposure to PBDEs were found to occur in winter, for both adults and children, but the PBDE concentrations were found not to pose appreciable risks to human health.

Sources and environmental behaviors of Dechlorane Plus and related compounds - A review

Although Dechlorane Plus (DP) has been used as a polychlorinated flame retardant for almost half a century, its detection in the environment was not reported until 2006. The subsequent intensive research has confirmed its global ubiquity. A few reviews have presented the properties, analytical methods and environmental occurrence of DP and related compounds in the past several years. The present review emphasizes on the environmental behavior of DP isomers which is assessed by the variation of the isomer ratio of DP in various matrices. Other aspects including the analytical methods, emission sources, general environmental occurrence and bioaccumulation of DP are also summarized. In this review, three typical emission sources in the environment are categorized after introducing the measurement method of DP. The temporal-spatial distribution is then evaluated at the global scale, which provides an integrated representation of the environmental occurrence of DP and potential impact on the human health and ecosystems. The variations of DP isomer ratio in various matrices reinforce its source related distribution and their stereoselective bioaccumulation. Thereafter, DP related compounds and dechlorinated analogs are briefly summarized in regards to their occurrence in various matrices, suggesting their ubiquity in the environment and bioavailability. Further studies are required to better assess the exposures and toxicological effects of DP and its analogs. A special concern is the serious contamination in e-waste recycling areas in developing countries, where long-term monitoring data on the association of DP exposure and adverse effects to human health and ecosystems is urgently needed.