Adsorption of Estrogen Contaminants by Graphene Nanomaterials under Natural Organic Matter Preloading: Comparison to Carbon Nanotube, Biochar, and Activated Carbon

Laser-machined micro-supercapacitors: from microstructure engineering to smart integrated systems

With the rapid development of portable and wearable electronic devices, there is an increasing demand for miniaturized and lightweight energy storage devices. Micro-supercapacitors (MSCs), as a kind of energy storage device with high power density, a fast charge/discharge rate, and a long service life, have attracted wide attention in the field of energy storage in recent years. The performance of MSCs is mainly related to the electrodes, so there is a need to explore more efficient methods to prepare electrodes for MSCs. The process is cumbersome and time-consuming using traditional fabrication methods, and the development of laser micro-nano technology provides an efficient, high-precision, low-cost, and convenient method for fabricating supercapacitor electrodes, which can achieve finer mask-less nanofabrication. This work reviews the basics of laser fabrication of MSCs, including the laser system, the structure of MSCs, and the performance evaluation of MSCs. The application of laser micro-nanofabrication technology to MSCs and the integration of MSCs are analyzed. Finally, the challenges and prospects for the development of laser micro-nano technology for manufacturing supercapacitors are summarized.

Simultaneous adsorption of fulvic acid and organic contaminants by KOH activated mesoporous biochar with large surface area

Returning carbon materials from biomass to soil is a potential technology to retard organic contaminants or dissolved organic matter (DOM) in soil by adsorption, as well as to store carbon in soil for carbon sequestration. However, DOM was widely reported to inhibit adsorption of organic contaminants on carbon materials by competition and by enhancing contaminants' solubility. In this study, a KOH activated carbon material (KAC), pyrolyzed from bamboo chips, with high surface area (3108 m2/g), micropores volumes (0.964 cm3/g), mesopores volumes (1.284 cm3/g), was observed that it can adsorb fulvic acid (FA) and organic contaminants (e.g., nitrobenzene, phenols, and anilines) simultaneously with weak competition and high adsorption capacity. With 50 mg TOC/L FA, for example, the average competition suppressing rate (ΔKf/Kf-m) of organic contaminants on KAC was lower than 5%, the adsorption for organic contaminants and FA were higher than 1100 mg/g and 90 mg TOC/g, respectively. The weak competition on KAC could be attributed to the low micropore blockage (<35%) and the weak adsorption sites competition on mesopores of KAC, as well as the minimal solubility enhancement of organic contaminants by FA because most FA is adsorbed on KAC but is not dissolved in the solution. In addition, adsorption of organic contaminants with high hydrogen-bonding donor ability (αm) and adsorption affinity was less suppressed by FA because of the heterogeneous nature of hydrophilic sites on KAC's surface. Therefore, KAC could be a potential carbon material to be produced to implement to soil for carbon storage and simultaneous retarding organic contaminants and DOM.

Effects of Mixtures of Engineered Nanoparticles and Cocontaminants on Anaerobic Digestion

The widespread application of nanotechnology inevitably leads to an increased release of engineered nanoparticles (ENPs) into the environment. Due to their specific physicochemical properties, ENPs may interact with other contaminants and exert combined effects on the microbial community and metabolism of anaerobic digestion (AD), an important process for organic waste reduction, stabilization, and bioenergy recovery. However, the complicated interactions between ENPs and other contaminants as well as their combined effects on AD are often overlooked. This review therefore focuses on the co-occurrence of ENPs and cocontaminants in the AD process. The key interactions between ENPs and cocontaminants and their combined influences on AD are summarized from the available literature, including the critical mechanisms and influencing factors. Some sulfides, coagulants, and chelating agents have a dramatic "detoxification" effect on the inhibition effect of ENPs on AD. However, some antibiotics and surfactants increase the inhibition of ENPs on AD. The reasons for these differences may be related to the interactive effects between ENPs and cocontaminants, changes of key enzyme activities, adenosine triphosphate (ATP) levels, reactive oxygen species (ROS) production, and microbial communities. New scientific opportunities for a better understanding of the coexistence in real world situations are converging on the scale of nanoparticles.

Deciphering the synergistic effects of photolysis and biofiltration to actuate elimination of estrogens in natural water matrix

The presence of estrogens in water environments has raised concerns for human health and ecosystems balance. These substances possess potent estrogenic properties, causing severe disruptions in endocrine systems and leading to reproductive and developmental problems. Unfortunately, conventional treatment methods struggle to effectively remove estrogens and mitigate their effects, necessitating technological innovation. This study investigates the effectiveness of a novel sequential photolysis-granular activated carbon (GAC) sandwich biofiltration (GSBF) system in removing estrogens (E1, E2, E3, and EE2) and improving general water quality parameters. The results indicate that combining photolysis pre-treatment with GSBF consistently achieved satisfactory performance in terms of turbidity, dissolved organic carbon (DOC), UV254, and microbial reduction, with over 77.5 %, 80.2 %, 89.7 %, and 92 % reduction, respectively. Furthermore, this approach effectively controlled the growth of microbial biomass under UV irradiation, preventing excessive head loss. To assess estrogen removal, liquid chromatography-tandem mass spectrometry (LC-MS) measured their concentrations, while bioassays determined estrogenicity. The findings demonstrate that GSBF systems, with and without photolysis installation, achieved over 96.2 % removal for estrogens when the spike concentration of each targeted compound was 10 µg L-1, successfully reducing estrogenicity (EA/EA0) to levels below 0.05. Additionally, the study evaluated the impact of different thicknesses of GAC layer filling (8 cm, 16 cm, and 24 cm) and found no significant difference (p>0.05) in estrogen and estrogenicity removal among them.

Current advances in the detection and removal of organic arsenic by metal-organic frameworks

Arsenic (As) is a highly toxic heavy metal and has been widely concerned for its hazardous environmental impact. Aromatic organic arsenic (AOCs) has been frequently used as an animal supplement to enhance feed utilization and prevent dysentery. The majority of organic arsenic could be discharged from the body and evolve as highly toxic inorganic arsenic that is hazardous to the environment and human health via biological conversion, photodegradation, and photo-oxidation. Current environmental issues necessitate the development and application of multifunctional porous materials in environmental remediation. Compared to the conventional adsorbent, such as activated carbon and zeolite, metal-organic frameworks (MOFs) exhibit a number of advantages, including simple synthesis, wide variety, simple modulation of pore size, large specific surface area, excellent chemical stability, and easy modification. In recent years, numerous scientists have investigated MOFs related materials involved with organic arsenic. These studies can be divided into three categories: detection of organic arsenic by MOFs, adsorption to remove organic arsenic by MOFs, and catalytic removal of organic arsenic by MOFs. Here, we conduct a critical analysis of current research findings and knowledge pertaining to the structural characteristics, application methods, removal properties, interaction mechanisms, and spectral analysis of MOFs. We summarized the application of MOFs in organic arsenic detection, adsorption, and catalytic degradation. Other arsenic removal technologies and conventional substances are also being investigated. This review will provide relevant scientific researchers with references.

Electrospun TiO2-GO/PAN-CA nanofiber mats: A novel material for remediation of organic contaminants and nitrophenol reduction

The outstanding properties of nanofiber composites have made them a popular choice for various structural applications. Recently, there has been a growing interest in using electrospun nanofibers as reinforcement agents, which possess exceptional properties that can enhance the performance of these composites. Herein, TiO2-graphene oxide (GO) nanocomposite incorporated into polyacrylonitrile (PAN)/cellulose acetate (CA) nanofibers were fabricated by an effortless electrospinning technique. The chemical and structural characteristics of the resulting electrospun TiO2-GO nanofibers were examined employing diverse techniques such as XRD, FTIR, XPS, TGA, mechanical properties, and FESEM. Remediation of organic contaminants and organic transformation reactions with electrospun TiO2-GO nanofibers were performed. The results indicated that the incorporation of TiO2-GO with various TiO2/GO ratios did not affect the molecular structure of PAN-CA. Still, they did significantly increase the mean fiber diameter (234-467 nm) and the mechanical properties of the nanofibers comprising UTS, elongation, Young's modulus, and toughness compared to PAN-CA. From various ratios of TiO2/GO (0.01TiO2/0.005GO and 0.005TiO2/0.01GO) in the electrospun NFs, the nanofiber containing a high content of TiO2 showed over 97% of the initial MB dyes were degraded after 120 min of visible light exposure and the same nanofibers also, achieved 96% nitrophenol conversion to aminophenol in just 10 min with activity factor kAF value of 47.7 g-1min-1. These findings illustrate the promise of TiO2-GO/PAN-CA nanofibers for use in various structural applications, particularly in the remediation of organic contaminants from water and organic transformation reactions.

Carbon-based nanomaterials mediated adsorption and photodegradation of typical organic contaminants in aqueous fulvic acid solution

In this work, the formation of carbon-based nanomaterials-fulvic acid (CNMs-FA) composites and their capacities for the adsorption and photodegradation of typical organic contaminants in aqueous solutions were investigated. The results suggested that the formation of CNMs-FA composites was dominated by adsorbing FA on CNMs via the physisorption process, which fit the pseudo-first-order kinetic model and the Langmuir isotherm model. The formed CNMs-FA composites were characterized by using the Brunauer-Emmett-Teller, scanning electron microscopy, and infrared spectroscopy techniques and further applied for examining their effects on the adsorption and photodegradation of selected organic contaminants in aqueous solutions. The adsorption of organic contaminants on CNMs-FA composites is mainly involved in hydrogen bonding and electrostatic interactions between organic contaminants and FA species adhering to CNMs. In addition, the CNMs-FA composites are able to promote the photosensitive degradation of organic contaminants due to the photogenerated reactive species including ROS and CNMs-3FA* under sunlight irradiation. This study provided a deeper and more comprehensive understanding of the environmental behavior of CNMs in real natural surface water and clarified the underlying mechanisms.

Interactions between H2O2 and dissolved organic matter during granular activated carbon-based residual H2O2 quenching from the upstream UV/H2O2 process

Granular activated carbon (GAC) filtration can be employed to synchronously quench residual H₂O₂ from the upstream UV/H₂O₂ process and further degrade dissolved organic matter (DOM). In this study, rapid small-scale column tests (RSSCTs) were performed to clarify the mechanisms underlying the interactions between H₂O₂ and DOM during the GAC-based H₂O₂ quenching process. It was observed that GAC can catalytically decompose H₂O₂, with a long-lasting high efficiency (>80% for approximately 50,000 empty-bed volumes). DOM inhibited GAC-based H₂O₂ quenching via a pore-blocking effect, especially at high concentrations (10 mg/L), with the adsorbed DOM molecules being oxidized by the continuously generated ·OH; this further deteriorated the H₂O₂ quenching efficiency. In batch experiments, H₂O₂ could enhance DOM adsorption by GAC; however, in RSSCTs, it deteriorated DOM removal. This observation could be attributed to the different ·OH exposure in these two systems. It was also observed that aging with H₂O₂ and DOM altered the morphology, specific surface area, pore volume, and the surface functional groups of GAC, owing to the oxidation effect of H₂O₂ and ·OH on the GAC surface as well as the effect of DOM. Additionally, the changes in the content of persistent free radicals in the GAC samples were insignificant following different aging processes. This work contributes to enhancing understanding regarding the UV/H₂O₂-GAC filtration scheme, and promoting the application in drinking water treatment.

Degradation of Tetracycline with Photocatalysis by CeO2-Loaded Soybean Powder Carbon

In the process of using photocatalysts to treat tetracycline (TC) wastewater, the degradation efficiency of soybean powder carbon material (SPC) can be improved by loading it with cerium oxide (CeO₂). In this study, firstly, SPC was modified by phytic acid. Then, the CeO₂ was deposited on modified SPC using the self-assembly method. Catalyzed cerium (III) nitrate hexahydrate (CeH₃NO₄) was treated with alkali and calcined at 600 °C under nitrogen. XRD, XPS, SEM, EDS, UV-VIS /DRS, FTIR, PL and N₂ adsorption-desorption methods were used to characterize the crystal structure, chemical composition, morphology, surface physical and chemical properties. The effects of catalyst dosage, monomer contrast, pH value and co-existing anions on TC oxidation degradation were investigated, and the reaction mechanism of a 600 Ce-SPC photocatalytic reaction system was discussed. The results show that the 600 Ce-SPC composite presents uneven gully morphology, which is similar to the natural "briquettes". The degradation efficiency of 600 Ce-SPC reached about 99% at 60 min under light irradiation when the optimal catalyst dosage and pH were 20 mg and 7. Meanwhile, the reusability of the 600 Ce-SPC samples showed good stability and catalytic activity after four cycles.

Estrogen adsorption from an aqueous solution on the chitosan nanoparticles

In this research, chitosan nanoparticles as an efficient and reusable adsorbent with adsorption capacity of 5.79 mg/g, surface area of 62 m²/g and pH_pzc of 8.07 were applied to remove the ethinylestradiol (as a sample of estrogen) from an aqueous wastewater. The chitosan nanoparticles were characterized by SEM, XRD and FT-IR analyses. Four independent variables involving contact time, adsorbent dosage, pH, and initial concentration of estrogen were applied to design the experiments by Design Expert software (CCD under RSM). In fact, number of experiments was minimized and the operating conditions were optimized for the maximum estrogen removal. The results indicated that three independent variables (contact time, adsorbent dosage, and pH) increment increased the estrogen removal while the estrogen initial concentration enhancement decreased the removal due to the concentration polarization phenomenon. The optimum conditions for the estrogen removal (92.50 %) on the chitosan nanoparticles were found at contact time of 220 min, adsorbent dosage of 1.45 g/l, pH of 7.3 and estrogen initial concentration of 5.7 mg/l. Moreover, the Langmuir isotherm and pseudo-second order models could properly legitimize estrogen adsorption process on the chitosan nanoparticles.

The impact of engineered nanomaterials on the environment: Release mechanism, toxicity, transformation, and remediation

The presence and longevity of nanomaterials in the ecosystem, as well as their properties, account for environmental toxicity. When nanomaterials in terrestrial and aquatic systems are exposed to the prevailing environmental conditions, they undergo various transformations such as dissociation, dissolution, and aggregation, which affects the food chain. The toxicity of nanomaterials is influenced by a variety of factors, including environmental factors and its physico-chemical characteristics. Bioaccumulation, biotransformation, and biomagnification are the mechanisms that have been identified for determining the fate of nanomaterials. The route taken by nanomaterials to reach living cells provides us with information about their toxicity profile. This review discusses the recent advances in the transport, transformation, and fate of nanomaterials after they are released into the environment. The review also discusses how nanoparticles affect lower trophic organisms through direct contact, the impact of nanoparticles on higher trophic organisms, and the possible options for remediation.

The response of steroid estrogens bioavailability to various sorption mechanisms by soil organic matter extracted with sequential alkaline-extraction method from an agriculture soil

The long-term groundwater contamination risks posed by steroidal estrogens (SEs) in animal-manured agricultural soils are closely associated with the soil organic matter (SOM) content and composition. In this study, the bioavailability of estrone (E1) and 17β-estradiol (17β-E2) under different sorption mechanism in humic acids (HA1 and HA2) and humin (HM) extracted with sequential alkaline-extraction technique (SAET) were examined. These SOMs extracted by SAET showed various properties and sorption characteristics for SEs. The alkyl carbon and condensed SOM increased during SAET, but aromatic carbon decreased and the same trend for polarity. Quick sorption was the major SEs sorption mechanism on HA1 and HA2, which contributed more than 69%; whilst slow sorption rate was about 50% in soil and HM. The logK_oc values were proportional to the TOC of SOM according to Freundlich fitting, and the sorption capacity of sorbent for E1 and 17β-E2 was related to the logK_ow values, indicating that the main mechanism controlling the SEs sorption was hydrophobic interaction. The larger micropore volume of HM and soil was more conducive to the micropore filling of SEs. Meanwhile, the specific sorption of SEs on condensed domain of SOM was the main reason for the strong desorption hysteresis and slow sorption in HM and soil. The SEs degradation rate was positively correlated with the contribution rate of quick adsorption and negatively correlated with the contribution rate of slow adsorption, indicating that the bioavailability of SEs sorbed by hydrophobic interaction was higher than that of micropore filling or specific sorption, which was also the reason for the low bioavailability of SEs in HM and soil. This work confirms the regulation of on-site SOM compositions and their properties on SEs sorption and bioavailability. Characterization of these details is crucial for the improved prediction of long-term risks to groundwater.

Carbon nanostructures: a comprehensive review of potential applications and toxic effects

There is no doubt that nanotechnology has revolutionized our life since the 1970s when it was first introduced. Nanomaterials have helped us to improve the current products and services we use. Among the different types of nanomaterials, the application of carbon-based nanomaterials in every aspect of our lives has rapidly grown over recent decades. This review discusses recent advances of those applications in distinct categories, including medical, industrial, and environmental applications. The first main section introduces nanomaterials, especially carbon-based nanomaterials. In the first section, we discussed medical applications, including medical biosensors, drug and gene delivery, cell and tissue labeling and imaging, tissue engineering, and the fight against bacterial and fungal infections. The next section discusses industrial applications, including agriculture, plastic, electronic, energy, and food industries. In addition, the environmental applications, including detection of air and water pollutions and removal of environmental pollutants, were vastly reviewed in the last section. In the conclusion section, we discussed challenges and future perspectives.

New insights into physicochemical properties of different particulate size-fractions and dissolved organic matter derived from biochars and their sorption capacity for phenanthrene

To improve the knowledge of the heterogeneity and sorption behavior of biochars on hydrophobic organic contaminants (HOCs), pristine biochars (PBCs, 400 and 700 °C) were fractionated into four particulate fractions (S_fBCs) and dissolved organic matter derived from biochars (DBC), then the sorption capacities of them towards phenanthrene were examined. Results showed that the OC-normalized sorption distribution coefficients (K_oc) of PBCs were generally at intermediate levels among that of S_fBCs and DBCs. The logK_oc values of S_fBCs increased as particle sizes decreased. By virtue of the higher micropore volume, specific surface area, aromaticity and hydrophobicity, the lowest S_fBCs (0.45-10 µm, BC_0.45-10) exhibited remarkably higher logK_oc. Besides, although S_fBCs from 700 °C generally showed larger logK_oc than counterparts from 400 °C, almost no difference was observed for logK_oc values of BC_0.45-10 fractions from 400 and 700 °C. We thus speculated that particle size might have stronger effect on their sorption capacity than pyrolysis temperature. Although DBCs exhibited dramatically lower logK_oc values than nano-scale S_fBCs, they were interestingly comparable to large-sized S_fBCs. Our findings thus suggested the importance of small particulate biochar species and DBCs on HOCs transport should be both highlighted since these fractions were highly dynamic in the environment.

Removal of estrogen pollutants using biochar-pellet-supported nanoscale zero-valent iron

Nanoscale zero-valent iron-supported biochar pellets (nZVI)-(BP) were synthesized via liquid-phase reduction and applied to estrogen removal, including estrone (E1), 17β-estradiol (E2), and estriol (E3). The performance of nZVI-BP, with respect to its characterization, removal kinetics, and isotherms, was investigated. The results showed that the adsorption equilibrium was reached within 10 min of exposure. The adsorption capacity of estrogen decreased with increasing solute pH and nZVI-BP dosage. The adsorptivity increased with increasing initial estrogen concentration. The estrogen behavior followed a pseudo-second-order kinetic model. The adsorption data of different initial estrogen concentrations fitted to Freundlich adsorption isotherms. In addition, a preliminary discussion of the adsorption mechanism of nZVI-BP for estrogens was provided.

An economical strategy towards the managing of selenium pollution from contaminated water: A current state-of-the-art review

During the last few decades, contamination of selenium (Se) in groundwater has turned out to be a major environmental concern to provide safe drinking water. The content of selenium in such contaminated water might range from 400 to 700 μg/L, where bringing it down to a safe level of 40 μg/L for municipal water supply employing appropriate methodologies is a major challenge for the global researcher communities. The current review focuses mostly on the governing selenium remediation technologies such as coagulation-flocculation, electrocoagulation, bioremediation, membrane-based approaches, adsorption, electro-kinetics, chemical precipitation, and reduction methods. This study emphasizes on the development of a variety of low-cost adsorbents and metal oxides for the selenium decontamination from groundwater as a cutting-edge technology development along with their applicability, and environmental concerns. Moreover, after the removal, the recovery methodologies using appropriate materials are analyzed which is the need of the hour for the reutilization of selenium in different processing industries for the generation of high valued products. From the literature survey, it has been found that hematite modified magnetic nanoparticles (MNP) efficiently adsorb Se (IV) (25.0 mg/g) from contaminated groundwater. MNP@hematite reduced Se (IV) concentration from 100 g/L to 10 g/L in 10 min at pH 4-9 using a dosage of 1 g/L. In 15 min, the magnetic adsorbent can be recycled and regenerated using a 10 mM NaOH solution. The adsorption and desorption efficiencies were over 97% and 82% for five consecutive cycles, respectively. To encourage the notion towards scale-up, a techno-economic evaluation with possible environmentally sensitive policy analysis has been introduced in this article to introspect the aspects of sustainability. This type of assessment is anticipated to be extremely encouraging to convey crucial recommendations to the scientific communities in order to produce high efficiency selenium elimination and further recovery from contaminated groundwater.

Insights into the adsorption of pharmaceuticals and personal care products (PPCPs) on biochar and activated carbon with the aid of machine learning

The science-informed design of 'green' carbonaceous materials (e.g., biochar and activated carbon) with high removal capacity of recalcitrant organic contaminants (e.g., pharmaceuticals and personal care products (PPCPs)) is indispensable for promoting sustainable wastewater treatment. In this study, machine learning (ML) incorporating PPCPs and biochar properties as well as adsorption conditions were applied to build adsorption prediction models and explore the contributions of various biochar's inherent properties to their PPCPs adsorption capacity. The results demonstrated that the models developed by detailed biochar properties (e.g., surface functionality and hierarchical porous structure) from advanced microscopic and spectroscopic techniques were more accurate (i.e., the root-mean-square error decreased by 18-24%) than those by general information such as bulk elemental composition and total pore volume. The relative importance of surface carbon functionalities ranked in the order of C-O bond > CO bond > non-polar carbon for predicting the adsorption capacity. According to the partial dependence analysis, the average pore diameters of adsorbents that were larger than the maximum diameter of PPCPs molecules by 1.5-fold to 2.5-fold favored the PPCPs adsorption. This study reveals new insights into the adsorption of PPCPs and provides a comprehensive reference for the sustainable engineering of biochar adsorbents for PPCPs wastewater treatment.

Carbonaceous composite membranes for peroxydisulfate activation to remove sulfamethoxazole in a real water matrix

In this study, we fabricated carbonaceous composite membranes by loading integrated mats of nitrogen-doped graphene, reduced graphene oxide, and carbon nanotubes (NG/rGO/CNTs) on a nylon microfiltration substrate and employed it for in-situ catalytic oxidation by activating peroxydisulfate (PDS) for the removal of sulfamethoxazole (SMX) in a real water matrix. The impact of coexisting organics on the performance of carbonaceous catalysis was investigated in the continuous filtration mode. Reusability testing and radical quenching experiments revealed that the non-radical pathways of surface-activated persulfate mainly contributed to SMX degradation. A stable SMX removal flux (r_SMX) of 22.15 mg m^-2·h^-1 was obtained in 24 h when tap water was filtered continuously under a low pressure of 1.78 bar and in a short contact time of 1.4 s, which was slightly lower than the r_SMX of 23.03 mg m^-2·h^-1 performed with deionized water as the control group. In addition, higher contents of protein-, fulvic acid-, and humic acid-like organics resulted in membrane fouling and significantly suppressed SMX removal during long-term filtration. Changes in the production of sulfate ions and the Raman spectra of carbon mats indicated that organics prevent the structural defects of the carbon matrix from participating in PDS activation. Moreover, NG/rGO/CNTs composite membranes coupled with activated persulfate oxidation exhibited good self-cleaning ability, because membrane fouling could be partly reversed by restoring filtration pressure during operation. This study provides a novel and effective oxidation strategy for efficient SMX removal in water purification, allowing the application of carbonaceous catalysis for the selective degradation of emerging contaminants.

Novel insights into the adsorption of organic contaminants by biochar: A review

With rising concerns in the practical application of biochar for the remediation of environment influenced by various organic contaminants, a critical review to facilitate insights the crucial role that biochar has played in wastewater and polluted soil decontamination is urgently needed. This research therefore aimed to describe different intriguing dimensions of biochar interactions with organic contaminants, which including: (i) an introduction of biochar preparation and the related physicochemical properties, (ii) an overview of mechanisms and factors controlling the adsorption of organic contaminants onto biochar, and (iii) a summary of the challenges and an outlook of the further research needs in this issue. In the light of the survey consequences, the appearance of biochar indicates the potential in substituting the existing costly adsorbents, and it has been proved that biochar is one promising adsorbent for organic pollutants adsorption removal from water and soil. However, some research gaps, such as dynamic adsorption, potential environmental risks, interactions between biochar and soil microbes, novel modification techniques, need to be further investigated to facilitate its practical application. This research will be conductive to better understanding the adsorption removal of organic contaminants by biochar.

Magnetically modified in-situ N-doped Enteromorpha prolifera derived biochar for peroxydisulfate activation: Electron transfer induced singlet oxygen non-radical pathway

Herein, in-situ N-doped Enteromorpha prolifera derived magnetic biochar (MBC) was prepared by loading Fe₃O₄. It can effectively activate peroxodisulfate (PDS) to degrade tetracycline (TC) and easy recycling. The removal rate of TC reached 87.2%, and its possible degradation pathway was revealed through a liquid chromatography-mass spectrometer. This work first proposes the mechanism of in-situ N-doping and Fe synergistic effect on PDS activation. Unlike the well-reported role of N doping in activating PDS, except for the edge pyridine N plays a significant role in the activation of PDS. After the load of Fe, the synergistic effect of Fe and graphite N induces a non-radical path dominated by singlet oxygen (¹O₂) due to the excellent electron transfer function. Through chemical quenching experiment, electron spin detection, and electrochemical analysis, the mechanism of PDS activation by MBC was thoroughly investigate. This research will deepen the understanding of the mechanism of transition metals and carbon materials in synergistically driving PDS activation, and guide biochar-mediated PDS activation in environmental remediation.

Metabolomics approach to study in vivo toxicity of graphene oxide nanosheets

Although graphene oxide (GO) nanosheets are widely used in different fields, the mechanism of their toxicity remains relatively unknown. NMR-based metabolomics was used to study in vivo time and dose-dependent toxicity of GO nanosheets in mice. Sixty serum samples from mice in four different time intervals including 24 and 72 h and 7 and 21 days after injection of 0-, 1-, and 10-mg/kg b.w. were analyzed based on ¹ HNMR spectra of each sample and multivariate methods. In comparison with the control group, 12 changed metabolites were identified in GO nanosheet-treated mice groups. These metabolites are involved in steroid hormone biosynthesis and steroid biosynthesis pathways. It was seen that the time factor is more important than the dose factor and the groups were separated in a time direction, completely. We found that GO nanosheets has toxicity and can affect steroidal hormones. However, this study shows that after 21 days, the treated groups regardless of their GO nanosheet dose are very close to the control group. This means that in one step exposure to GO nanosheets, their toxicity diminished after 21 days.

Accurate Removal of Trace 17β-Estradiol and Estrogenic Activity in Blended Systems under a Photoelectrocatalytic Circulating Flow

Trace 17β-estradiol (E2) is persistent against advanced treatment when blended with higher concentrations of low-toxicity organics, thus wasting energy. A circulating-flow selective photoelectrocatalysis (CF-SPEC) system is established with a selective E2-TiO₂-NR photoanode, accurately reducing 1 μg L^-1 E2 to less than 0.1 ng L^-1 along with eliminating estrogenic activity even when blended with natural organic matter (NOM) at a thousand times higher concentration. Such high efficiency is derived from the augmented selectivity and activity of E2-TiO₂-NRs toward E2 during CF-SPEC. Under a flow, the difference in adsorption capacity between NOM and E2 is further amplified 5.6-fold. Furthermore, the higher initial ^•OH concentration and faster mass transfer jointly endow CF-SPEC with a stronger oxidation capacity. As a result, the removal of E2 increases by 58.7%, and the elimination of estrogenic activity increases 5.8-fold. In addition, deeper mineralization and less homo- and heterocoupling under CF-SPEC are observed, leading to more thorough estrogenic activity removal. Although additional energy is needed to maintain the flow, there is a 55% decrease in energy consumption due to the accurate removal capacity. This work suggests a combination of flow degradation and surface engineering that can be expanded for the selective removal of toxic trace pollutants in blended systems.

High-efficiency removal of tetracycline by carbon-bridge-doped g-C3N4/Fe3O4 magnetic heterogeneous catalyst through photo-Fenton process

Carbon-bridge-modified malonamide (MLD)/g-C₃N₄ (CN) was prepared by copolymerization of MLD with urea and melamine and loaded with Fe₃O₄ for the high-efficiency removal of tetracycline (TC) in water under photo-Fenton. The prepared catalysts were characterized by SEM, TEM, N₂ adsorption-desorption analysis, XPS, XRD, and FTIR, which proved that the modification method successfully introduced the C bridge into the carbon nitride molecular system and increased the structural defects of the catalyst. The Carbon-bridge-modified MLD/CN/Fe₃O₄ also had good visible-light response and charge-separation and transport abilities in the photoelectrochemical test. Degradation results showed that the photo-Fenton degradation of TC reached 95.8%, and the mineralization rate was 55.7% within 80 min at 80 mM H₂O₂ dosage, 0.5 g/L catalyst dosage, and near-neutral pH by 0.8MLD/CN/Fe₃O₄. Moreover, the oxidation products and mineralization pathways of TC were explored by LC-MS. Toxicity analysis indicated low environmental threat of the intermediates in TC mineralization. EPR analysis and H₂O₂ decomposition efficiency analyses showed an improvement in the H₂O₂ decomposition performance of 0.8MLD/CN/Fe₃O₄. This work could provide a valuable insight for the application of heterogeneous photo-Fenton technology in wastewater treatment.

Environmentally friendly fabrication of new β-Cyclodextrin/ZrO2 nanocomposite for simultaneous removal of Pb(II) and BPA from water

Heavy metals and endocrine disrupters often co-exist in wastewater, while their possible competition behaviours make uptake removal more challenging. Therefore, β-Cyclodextrin based nanocomposite adsorbent was successfully fabricated (β-Cyclodextrin/ZrO₂) for the simultaneous uptake of Pb(II) and Bisphenol A from wastewater. FTIR, XRD, and XPS confirmed the successful fabrication of the β-Cyclodextrin/ZrO₂ nanocomposite. In this setting, oxygen-containing groups are primarily responsible for the Pb(II) binding, while the β-Cyclodextrin cavities adsorb Bisphenol A through host-guest interaction, enabling the simultaneous removal of Pb(II) and Bisphenol A. In the mono contaminant system, the nanocomposite displayed prominent removal ability toward Pb(II) and Bisphenol A with adsorption characteristics of pseudo-second-order, Langmuir, and Freundlich isotherm model. The maximum adsorption capacities were identified for Pb(II) and Bisphenol A to be 274.4 mg/g and 174.9 mg/g at 298 K, respectively. Most importantly, the β-Cyclodextrin/ZrO₂ could efficiently attain simultaneous removal of Pb(II) and Bisphenol A by avoiding their competitive behaviours was due to the different adsorption mechanisms (electrostatic interaction and host-guest interaction). Moreover, the adsorbed Pb(II) and Bisphenol A could be successfully recovered with a slight decline in nanocomposite removal performance even after 4 cycles in the binary-component system. All these findings provide insights into the fabrication of highly effective adsorbent with separated adsorption sites to treat wastewater bearing heavy metal and endocrine disrupters.

Effects of zinc oxide nanoparticles on antioxidants, chlorophyll contents, and proline in Persicaria hydropiper L. and its potential for Pb phytoremediation

Applications of nanoparticles and plants for efficient restoration of heavy metal-polluted water and soil are an emerging approach and need to be explored. Hydroponic study was performed to find the role of zinc oxide nanoparticles (ZnO NPs) in plant growth, antioxidative response, and lead (Pb) accumulation in Persicaria hydropiper. Seedlings were grown in Pb-polluted media amended with 5, 10, 15, and 20 mg L^-1 ZnO NPs. Inductively coupled plasma spectroscopy (ICP) was used for Pb analysis in plant tissues. Pb significantly inhibited seedling growth, and ZnO NPs alleviated Pb-induced stress by promoting plant growth, and improved chlorophyll and carotenoid contents. Oxidative stress ameliorated in ZnO NPs exposed seedlings through enhanced production of free proline, phenolics, flavonoids, and activation of antioxidative enzymes. Pb accumulation boosted in ZnO NP treatments, and highly significant increase in Pb accumulation in roots (255.60±4.80 mg kg^-1), stem (124.07±2.84 mg kg^-1), and leaves (92.00±3.22 mg kg^-1) was observed in T3 (15 mg L^-1 ZnO NPs) for P. hydropiper. Contrarily, ZnO NPs at 20 mg L^-1 dose suppressed plant growth, Pb accumulation, secondary metabolites, and antioxidative enzyme activities. Moreover, positive correlation was found in Pb accumulation with free proline and secondary metabolite contents in plant tissues. These results suggest that ZnO NPs at optimum concentration may augment efficacy of plants to remove heavy metal from polluted water through nanophytoremediation.

Organic matter interference with steroid hormone removal by single-walled carbon nanotubes - ultrafiltration composite membrane

Composite adsorbent-ultrafiltration membranes for micropollutant removal are an interesting concept, although water matrix compounds, such as organic matter (OM), may interfere with micropollutant adsorption. To prevent this interference, the adsorbents such as single-walled carbon nanotubes (SWCNTs) can be deposited on the permeate side of an ultrafiltration membrane (UF) that can retain OM. In this study, the 'shielding' effect by different UF MWCOs of such an SWCNT-UF composite was evaluated for nine different types of OM. All nine OM types competed with 17β-estradiol (E2) for adsorption to varying extents, and tannic acid (TA, 1.7 kDa) reduced E2 adsorption by SWCNT-UF most drastically. TA interference mechanisms included direct competition with hormones for adsorption sites, and indirect competition via TA-hormone interactions. TA was not fully retained by the composite membrane with an MWCO range of 3-100 kDa, resulting in ineffective shielding. In contrast, humic acid was mostly retained by the composite with low MWCO of 3-10 kDa and allowed high E2 adsorption. This study demonstrates that tailoring composite membranes by carefully choosing UF MWCO can prevent interference of OM types in micropollutant adsorption by permeate-side adsorbents.

Opposite impacts of chemical oxidation for ofloxacin adsorption on activated carbon and carbon nanotubes

The adsorption of ofloxacin (OFL) on oxidized activated carbon (AC) and carbon nanotube (CNT) are compared, focusing on the differences in carbon structures. Chemical oxidation of carbonaceous materials inhibited OFL adsorption to AC, but enhanced their adsorption to CNT. The higher number of oxygen-containing functional groups facilitated the interaction of the material with water molecules, causing the blockage of AC inner pore. However, the dispersion of oxidized CNT enhanced due to its increased hydrophilicity, resulting in the exposure of some new adsorption sites, as identified by the ¹H NMR relaxometry measurement. The adsorption kinetics of OFL on AC indicated that the contributions of slow adsorption and equilibrium time increased after AC oxidation. However, the equilibrium time of the fast adsorption of OFL on CNT shortened after CNT oxidation. These results indicated that the pore of AC was blocked by water cluster and the accessibility of adsorption sites on oxidized CNT was enhanced due to dispersion. This study emphasizes that the structural differences among carbonaceous materials control the oxidation effects on their adsorption characteristics for OFL.

Nanoparticles-EPS corona increases the accumulation of heavy metals and biotoxicity of nanoparticles

Microbial extracellular polymeric substances (EPS) coating nanoparticles (NPs) surface can form NPs-EPS corona, which significantly affect the adsorption of NPs to toxic substances and alter the ecotoxicological effect of NPs. In this work, the EPS coronas on TiO₂ NPs (TNPs) and CeO₂ NPs (CNPs) were characterized and the adsorption characteristics of NPs with and without EPS corona to five heavy metals were investigated in single-metal and multiple-metal systems. The results of spectral analysis showed that NPs-EPS corona exhibited new crystalline phases and abundant functional groups. Moreover, 42 and 13 proteins were identified in the TNPs-EPS and CNPs-EPS coronas, respectively. The rates of Cd²⁺, Pb²⁺, Cu²⁺, Ni²⁺ and Ag⁺ adsorption by NPs-EPS corona increased to values that were 6.7-7.6, 4.4-5.1, 4.2-5.5, 3.9-4.9 and 8.5-8.8 times those of NPs without EPS corona, respectively, in single-metal system. NPs-EPS coronas are effective in absorbing Ag⁺, Pb²⁺ and Cu²⁺ compared with Cd²⁺and Ni²⁺ in multiple metal adsorption. These results indicated that NPs-EPS corona effectively adsorb and remove heavy metals by forming NPs-EPS-metal complexes and inducing precipitation. However, NPs-EPS corona can enhance the toxicity of NPs by accumulating highly-toxic heavy metals in aquatic environments.

Scalable synthesis and purification of functionalized graphene nanosheets for water remediation

Microwave (MW) accelerated synthesis combined with microfiltration (MF) on commercial hollow fiber modules enables fast and scalable preparation of highly pure modified graphene oxide nanosheets. The MW-MF procedure is demonstrated on polyethylenimine (PEI) modified GO, and the so-obtained GOPEI is used for simultaneous removal of arsenic and lead from water.

Adsorption of 17α-Ethinyl Estradiol and Bisphenol A to Graphene-Based Materials: Effects of Configuration of Adsorbates and the Presence of Cationic Surfactant

Endocrine-disrupting chemicals (EDCs) have attracted much attention in recent years. Graphene-based materials (GMs) have been deemed as excellent adsorbents for the removal of EDCs. The objective of the present study was to understand how the cationic surfactants (CTAB; cetyltrimethylammonium nitrate) affect the adsorption of EDCs (17α-ethinyl estradiol (EE2) and bisphenol A (BPA)) on graphene oxide (GO), reduced graphene oxides (RGOs), and the few-layered commercial graphene (CG). It was observed that the presence of CTAB showed different effects on the adsorption of EDCs to different GMs. The adsorption of EDCs on GO was enhanced because of the enhanced hydrophobicity of GMs after the adsorption of CTAB and the newly formed hemimicelles by the adsorbed CTAB, which could serve as the partition phase for EDCs. Moreover, the electron donor-acceptor interaction and cation bridging effect of the –NH4+ group of the adsorbed CTAB between EDCs and GMs could also enhance the adsorption of EDCs to GMs. With the increase of the extent of GM reduction, the adsorption enhancement by the presence of CTAB weakened. This could be attributed to the competition and pore blockage effect caused by the adsorbed CTAB. It is worth noting that the enhancement of CTAB on the adsorption of BPA to GMs was more profound than that of EE2. This is likely because the pore blockage effect plays a less important role in the adsorption of BPA due to its smaller molecular diameter and deformable structure.

Core-shell graphene oxide-polymer hollow fibers as water filters with enhanced performance and selectivity

Commercial hollow fiber filters for micro- and ultrafiltration are based on size exclusion and do not allow the removal of small molecules such as antibiotics. Here, we demonstrate that a graphene oxide (GO) layer can be firmly immobilized either inside or outside polyethersulfone-polyvinylpyrrolidone hollow fiber (Versatile PES®, hereafter PES) modules and that the resulting core-shell fibers inherits the microfiltration ability of the pristine PES fibers and the adsorption selectivity of GO. GO nanosheets were deposited on the fiber surface by filtration of a GO suspension through a PES cartridge (cut-off 0.1-0.2 μm), then fixed by thermal annealing at 80 °C, rendering the GO coating stably fixed and unsoluble. The filtration cut-off, retention selectivity and efficiency of the resulting inner and outer modified hollow fibers (HF-GO) were tested by performing filtration on water and bovine plasma spiked with bovine serum albumin (BSA, 66 kDa, ≈15 nm size), monodisperse polystyrene nanoparticles (52 nm and 303 nm sizes), with two quinolonic antibiotics (ciprofloxacin and ofloxacin) and rhodamine B (RhB). These tests showed that the microfiltration capability of PES was retained by HF-GO, and in addition the GO coating can capture the molecular contaminants while letting through BSA and smaller polystyrene nanoparticles. Combined XRD, molecular modelling and adsorption experiments show that the separation mechanism does not rely only on physical size exclusion, but involves intercalation of solute molecules between the GO layers.

Interactions between carbon-based nanoparticles and steroid hormone micropollutants in water

The occurrence of micropollutants (MPs) including steroid hormones is a global environmental and health challenge. Carbon-based nanoparticles can be incorporated with water treatment processes to allow MP removal by adsorption. The aim was to compare the suitability of such nanoparticles (graphene, graphene oxide, carbon nanotubes and C₆₀) to adsorb steroid hormones for later incorporation in membrane composites. All nanoparticles displayed fast kinetics; carbon nanotubes and graphene showed high adsorption capacities for hormones undeterminable in isotherm studies (over 10 mg/g). External surface adsorption appears to be the most prominent factor impacting adsorption performance. Structure, conformation, geometry and surface charge of nanoparticles can influence the accessibility of surface area through colloidal instability in aqueous solution. Mechanism inspection shows that adsorption initiates at long ranges (up to 10 nm) through hydrophobic and electrostatic interactions. At relatively short ranges (0.2-0.5 nm), adsorption is enhanced by π/π stacking, XH / π (X = C, O) interactions, van der Waals forces and hydrogen bonding. Both long- and short-range forces transporting hormones from the liquid bulk into the adsorbed phase could control the rate. With relatively short residence time required and high adsorption capacity, carbon nanotubes and graphene are promising for incorporation in a membrane composite.

Recent progress of graphene based nanomaterials in bioelectrochemical systems

The application of graphene (Gr) to microbial fuel cells (MFCs) and microbial electrolysis cell (MECs) is considered a very promising approach in terms of enhancing their performance. The superior Gr properties of high electrical and thermal conductivities, along with: superior specific surface area, high electron mobility, and mechanical strength, are the key features that endorse this. Factors impeding the advancement of a microbial fuel cell into commercialization involve primarily the cost of their components, and their production on a small scale. Gr with such outstanding characteristics can help mitigate these challenges, when used as electrode material. The application of Gr as an anode material improves the efficiency of electron transfer and bacterial attachment. When used as a cathode material, it supports the oxygen reduction reaction. This investigation, presents a thorough analysis of the feasibility of Gr as an electrode material in both MFC and MEC applications - based on experimental results from the investigation. Current technological advancements in the implementation of Gr in MFC and MEC are also highlighted in this review. To summarise, the investigation exposes critical issues impeding the advancement of microbial fuel cells, and proposes possible solutions to mitigate these challenges.

Biochar based sorptive remediation of steroidal estrogen contaminated aqueous systems: A critical review

Remediation of steroidal estrogens from aqueous ecosystems is of prevailing concern due to their potential impact on organisms even at trace concentrations. Biochar (BC) is capable of estrogen removal due to its rich porosity and surface functionality. The presented review emphasizes on the adsorption mechanisms, isotherms, kinetics, ionic strength and the effect of matrix components associated with the removal of steroidal estrogens. The dominant sorption mechanisms reported for estrogen were π-π electron donor-acceptor interactions and hydrogen bonding. Natural organic matter and ionic species were seen to influence the hydrophobicity of the estrogen in multiple ways. Zinc activation and magnetization of the BC increased the surface area and surface functionalities leading to high adsorption capacities. The contribution by persistent free radicals and the arene network of BC have promoted the catalytic degradation of adsorbates via electron transfer mechanisms. The presence of surface functional groups and the redox activity of BC facilitates the bacterial degradation of estrogens. The sorptive removal of estrogens from aqueous systems has been minimally reviewed as a part of a collective evaluation of micropollutants. However, to the best of our knowledge, a critique focusing specifically and comprehensively on BC-based removal of steroidal estrogens does not exist. The presented review is a critical assessment of the existing literature on BC based steroidal estrogen adsorption and attempts to converge the scattered knowledge regarding its mechanistic interpretations. Sorption studies using natural water matrices containing residue level concentrations, and dynamic sorption experiments can be identified as future research directions.

Efficient Removal 17-Estradiol by Graphene-Like Magnetic Sawdust Biochar: Preparation Condition and Adsorption Mechanism

The occurrence of environmental endocrine disrupting chemicals (EDCs) in aquatic environments has caused extensive concern. Graphene-like magnetic sawdust biochar was synthesized using potassium ferrate (K₂FeO₄) to make activated sawdust biochar and applied for the removal of 17-estradiol (E2). The characterization showed that the surface morphology of five graphene-like magnetic sawdust biochars prepared with different preparation conditions were quite different. The specific surface area and pore structure increased with the increment of K₂FeO₄ addition. The results have shown that graphene-like magnetic sawdust biochar (1:1/900 °C) had the best removal on E2. The experimental results indicated that pseudo-first-order kinetic model and the Langmuir model could describe the adsorption process well, in which the equilibrium adsorption capacity (q_e,1) of 1:1/900 °C were 59.18 mg·g⁻¹ obtained from pseudo-first-order kinetic model and the maximum adsorption capacity (q_max) of 1:1/900 °C were 133.45 mg·g⁻¹ obtained from Langmuir model at 298K. At the same time, lower temperatures, the presence of humic acid (HA), and the presence of NaCl could be regulated to change the adsorption reaction in order to remove E2. Adsorption capacity was decreased with the increase of solution pH because pH value not only changed the surface charge of graphene-like magnetic sawdust biochar, but also affected the E2 in the water. The possible adsorption mechanism for E2 adsorption on graphene-like magnetic sawdust biochar was multifaceted, involving chemical adsorption and physical absorption, such as H-bonding, π-π interactions, micropore filling effects, and electrostatic interaction. To sum up, graphene-like magnetic sawdust biochar was found to be a promising absorbent for E2 removal from water.

Determination of optimal operating parameters for tetracycline removal by adsorption from synthetic and real aqueous solutions

Among all emerging contaminants, pharmaceutical compounds as tetracycline (TC) can cause potential environmental impact in water quality. In this work, the removal of TC drug on activated carbon from aqueous solution was studied and the best operating parameters were obtained. In addition, a real aqueous matrix was enriched with TC and the optimized conditions were applied to study the adsorption process efficiency. For this, the influence of pH, contact time between phases and dosage of adsorbent solid was evaluated. The investigation of kinetics, equilibrium and thermodynamic was also performed. The adsorbent material was characterized by SEM analysis and N₂ adsorption/desorption isotherms to confirm its properties. Batch experiments showed that the most suitable experimental conditions for adsorption in aqueous solution were: pH 4.0, contact time 90 min and dosage of adsorbent solid 30 g.L^-1. Under these conditions, it was possible to obtain 92.7% of TC removal with predominance of a spontaneous, favorable and endothermic chemisorption process. Adsorption experiments with real aqueous matrix provided 99.4% TC removal. These results show the potential of adsorption as a wastewater treatment applied to remove emerging pollutants as TC from real aqueous contaminated water.

Adsorptive removal of apramycin antibiotic from aqueous solutions using Tween 80-and Triton X-100 modified clinoptilolite: experimental and fixed-bed modeling investigations

This study examined the performance of natural clinoptilolite (NC) modified with two surfactants of Triton X-100 (NC-Triton) and Tween 80 (NC-Tween) on apramycin (APR) adsorption from wastewater in batch and continues systems. The optimum pH, contact time, adsorbent dosage, and temperature were achieved. The findings revealed that the sorption was best described using the Langmuir isotherm compared to other isotherms. The maximum adsorption capacity of NC-Triton was greater than NC and NC-Tween. The lumped method was applied to solve the fixed-bed equations; predict breakthrough curve; determine axial dispersion coefficient and overall mass transfer coefficient parameters; and compare theoretical results with experimental results. Good fitness of experimental data with kinetic models of intra-particle diffusion, pseudo-first-order/liquid film diffusion and pseudo-second-order for NC, NC-Tween and NC-Triton, respectively, indicated that they were more suitable than the other models. Endothermic and spontaneous processes were resulted from positive enthalpy and negative Gibbs free energy changes, respectively.

Developments in the Application of Nanomaterials for Water Treatment and Their Impact on the Environment

Nanotechnology is an uppermost priority area of research in several nations presently because of its enormous capability and financial impact. One of the most promising environmental utilizations of nanotechnology has been in water treatment and remediation where various nanomaterials can purify water by means of several mechanisms inclusive of the adsorption of dyes, heavy metals, and other pollutants, inactivation and removal of pathogens, and conversion of harmful materials into less harmful compounds. To achieve this, nanomaterials have been generated in several shapes, integrated to form different composites and functionalized with active components. Additionally, the nanomaterials have been added to membranes that can assist to improve the water treatment efficiency. In this paper, we have discussed the advantages of nanomaterials in applications such as adsorbents (removal of dyes, heavy metals, pharmaceuticals, and organic contaminants from water), membrane materials, catalytic utilization, and microbial decontamination. We discuss the different carbon-based nanomaterials (carbon nanotubes, graphene, graphene oxide, fullerenes, etc.), and metal and metal-oxide based nanomaterials (zinc-oxide, titanium dioxide, nano zerovalent iron, etc.) for the water treatment application. It can be noted that the nanomaterials have the ability for improving the environmental remediation system. The examination of different studies confirmed that out of the various nanomaterials, graphene and its derivatives (e.g., reduced graphene oxide, graphene oxide, graphene-based metals, and graphene-based metal oxides) with huge surface area and increased purity, outstanding environmental compatibility and selectivity, display high absorption capability as they trap electrons, avoiding their recombination. Additionally, we discussed the negative impacts of nanomaterials such as membrane damage and cell damage to the living beings in the aqueous environment. Acknowledgment of the possible benefits and inadvertent hazards of nanomaterials to the environment is important for pursuing their future advancement.