Highly Enhanced Crystallization Kinetics of Poly(l-lactic acid) by Poly(ethylene glycol) Grafted Graphene Oxide Simultaneously as Heterogeneous Nucleation Agent and Chain Mobility Promoter

Trace sorbitol-modified nano-silica: Towards nano-nucleation for poly(L-lactic acid)

Nucleating agents, especially those with small particle sizes, are preferred to boost the nucleation density and crystallinity of poly(lactic acid) (PLA) due to its weak crystallization capability. Organophilicly modified nanofillers hardly alter the nucleation and crystallinity of non-isothermally crystallized PLA. Herein, nano-silica adsorbed trace D-sorbitol (m-SiO2) as a heterogeneous nucleating agent was melt-mixed with poly(L-lactic acid) (PLLA), and the isothermal and non-isothermal crystallization behavior, as well as crystallization kinetics, were investigated. Transmission electron microscopy (TEM) revealed that m-SiO2 was uniformly dispersed in the PLA matrix as 100-300 nm clusters. Differential scanning calorimetry (DSC) and polarized optical microscopy (POM) showed that the nucleation rate and density of the non-isothermally crystallized PLLA/m-SiO2 composites were significantly improved. Despite the fact that m-SiO2 does not raise the overall non-isothermal crystallization rate, the crystallization temperature and crystallinity of the PLLA/3%m-SiO2 composite increased from 97.2 °C and 6.8 % for neat PLLA to 108.2 °C and 48.6 % (10 °C/min cooling rate), respectively. The Avrami exponent n of isothermal crystallization remains unchanged, while the crystallization rate increases dramatically. Both isothermal and non-isothermal crystallization have increased activation energies. The heat deflection temperature increased from 59 °C of neat PLLA to 152 °C with a 50 % increase in impact strength.

Understanding the Impact of Chain Mobility on Conformational Evolution and Kinetics of Mesophase Formation in Poly(ʟ-lactide) under Low-Pressure CO2

Although the mesomorphic phase as an intermediate state has been introduced to understand polymer crystallization, the understanding of the mesomorphic phase is far from complete. Here, the effect of chain mobility on the mesophase structuring in melt-quenched poly(ʟ-lactide) (PLLA) treated in low-pressure CO2 at 1.6-2.0 MPa and 0 °C was investigated using infrared (IR) spectroscopy, differential scanning calorimetry (DSC), and atomic force microscopy (AFM). The IR and AFM results demonstrated that the final degree of order and the kinetics of structural evolution during the CO2-induced mesophase formation were critically dependent on the CO2 pressure. This was attributed to the distinct dynamics of conformational evolution (gg to gt conformer transition) due to the different CO2 pressures. The thermal behavior from the DSC results showed that CO2 pressure dominated both the scale and dynamics of the chain motion of PLLA. At a lower CO2 pressure of 1.6 MPa, smaller-scale segmental motion was not replaced by the larger-scale cooperative motion that occurred at a relatively higher CO2 pressure of 2 MPa, which was favorable for faster mesophase formation. Consequently, by inhibiting direct crystallization under limited mobility conditions, it was demonstrated that different chain mobility controlled by CO2 pressure and thus CO2 solubility impacted the dynamics of the mesophase formation of PLLA. The present results have implications for understanding the role of chain mobility in determining the intermediate structural phases in semicrystalline polymers.

Polyethylene glycol-grafted graphene oxide nanosheets in tailoring the structure and reverse osmosis performance of thin film composite membrane

Introducing hydrophilic polymers such as polyethylene glycol (PEG) within the polyamide (PA) layer of thin film composite (TFC) membranes helps achieve high water desalination performance. Here, PEGs of different molecular weights (X: 1500, 6000, 16,000 g/mol) are effectively introduced into the PA layer of TFC membranes utilizing PEG-grafted graphene oxide (GOPX) nanosheets and their effects on the physicochemical properties and reverse osmosis (RO) performance of the thin film nanocomposite (TFN) membranes are investigated. Among the TFNs prepared the GOP16000/TFN exhibits the best performance with 68% improvement in water flux and almost constant salt rejection compared to those of the bare TFC. The influence of PEG molecular weight on the RO performance of the membranes is interpreted by different surface and bulk hydrophilicity as well as thickness and surface roughness of PA layers of GOPX/TFNs. Furthermore, TFNs with thinner and smoother PA layers and thus higher water flux are obtained by dispersing GOPXs in the aqueous phase of the PA interfacial polymerization reaction than by dispersing them in the organic phase of the reaction. Finally, the high antifouling potential of TFNs containing PEG-grafted GOs is demonstrated.

A new class of nucleating agents for poly(L-lactic acid): Environmentally-friendly metal salts with biomass-derived ligands and advanced nucleation ability

Adding nucleating agents has been a successful strategy to boost the heat resistance of poly(L-lactic acid) (PLLA) by increasing the crystallinity. In this study, a new series of bio-based complexes as nucleating agents for PLLA, including twelve combinations of three eco-friendly metal ions (Zn, Mg, Ca) and four biomass-derived α-hydroxy acids, were successfully synthesized to respectively investigate the effects of metal ions as well as ligands on nucleation capacity of complexes. By investigating the non-isothermal and isothermal crystallization at 135 °C of PLLA with 0.3 wt% loading of complexes, both zinc and magnesium salts of L-mandelic acid showed excellent nucleation capacities. And magnesium L-mandelate performed better, raising the crystallinity of PLLA to 44.4 % as well as minimizing its crystallization half-time from 73 min to 2.7 min. The growth and denser distribution of PLLA spherulites on the salt surface were also observed by POM, reflecting epitaxial nucleation as the possible mechanism. A novel inspiration, utilizing VESTA software to simulate the crystal structure of zinc L-mandelate (Zn(L-MA)₂), was proposed to determine the nucleation mechanism. Also, using polyethylene terephthalate (PET) as a test protocol, the rationality of the model could be approved by checking the fitness of nucleating prediction and experiment results.

PEG-Grafted Graphene/PLLA Nanocomposites: Effect of PEG Chain Length on Crystallization Kinetics of PLLA

Poly-l-lactic acid (PLLA) nanocomposites containing graphene oxide (GO), modified with different chain lengths of poly(ethylene glycol) (PEG) (400, 2000, and 10 000 g/mol), were prepared by solution casting. The effect of the PEG chain length and nanoparticle content (0.5, 1, and 1.5 wt %) on the nucleation, crystal growth rate, and overall crystallization rate, under isothermal conditions, was then evaluated. The results showed that, in samples containing GO modified with 400 g/mol of PEG, the nucleation density increased as a function of a modified nanoparticle concentration. In the case of the samples containing GO modified with PEG of a molar mass of either 2000 or 10 000 g/mol, the nucleation density exhibited a maximum at a concentration of 1 wt %. Furthermore, the addition of graphene oxide modified with poly(ethylene glycol) of a molar mass of 2000 g/mol resulted in the largest nucleation, fastest crystal growth, and highest overall crystallization rate, for all concentrations. The results were explained in light of the steric hindrance between the modified nanoparticles.

Stereocomplexation Reinforced High Strength Poly(L-lactide)/Nanohydroxyapatite Composites for Potential Bone Repair Applications

Composite materials composed of polylactide (PLA) and nano-hydroxyapatite (n-HA) have been recognized as excellent candidate material in bone repai The difference in hydrophilicity/hydrophobicity and poor interfacial compatibility between n-HA filler and PLA matrix leads to non-uniform dispersion of n-HA in PLA matrix and consequent poor reinforcement effect. In this study, an HA/PLA nanocomposite was designed based on the surface modification of n-HA with poly(D-lactide) (PDLA), which not only can improve the dispersion of n-HA in the poly(L-lactide) (PLLA) matrix but also could form a stereocomplex crystal with the matrix PLLA at the interface and ultimately lead to greatly enhanced mechanical performance The n-HA/PLA composites were characterized by means of scanning electron microscopy, Fourier transform infrared spectroscopy, X-Ray diffraction, thermal gravity analysis, differential scanning calorimetry, and a mechanical test; in vitro cytotoxicity of the composite material as well as its efficacy in inducing osteogenic differentiation of rat bone marrow stromal cells (rMSCs) were also evaluated. Compared with those of neat PLLA, the tensile strength, Young's modulus, interfacial shear strength, elongation at break and crystallinity of the composites increased by 34%, 53%, 26%, 70%, and 17%, respectively. The adhesion and proliferation as well as the osteogenic differentiation of rMSCs on HA/PLA composites were clearly evidenced. Therefore, the HA/PLA composites have great potential for bone repai.

Experimental and Statistical Analysis of Saw Mill Wood Waste Composite Properties for Practical Applications

The utilization of composite materials is increasing at a growing rate in almost all types of products, due to their strength-to-stiffness ratio. From this perspective, natural waste composites, i.e., wood waste composites, have also been investigated for their effective and sustainable employment. This paper deals with the application of hard and soft wood waste (i.e., acacia and cedar wood) with epoxy resin polymer to develop high strength and thermally stable wood composites. Mechanical (tensile, flexural, impact, and hardness) and thermal properties of samples are studied using Differential Scanning Calorimeter (DSC) and Thermo Gravimetric Analysis (TGA), respectively. The properties are evaluated by varying the type of wood waste and its percentage by weight. Based on the Taguchi Orthogonal Array Mixture Design, eighteen experiments are investigated. Analysis of variance (ANOVA) results show that wood waste type and wood waste content have a significant effect on all mechanical properties. From the TGA analysis, it is predicted that both types of wood waste composites exhibit similar thermal-induced degradation profiles in terms of the initial and final degradation temperatures. From the DSC results, higher glass transition temperature T_g is detected in 10% of the hardwood waste composite, and a reducing tendency of glass transition temperature T_g is observed with exceeding wood waste content. Moreover, hardwood waste at 10% demonstrated improved decomposition temperature T_d, due to strong adhesion between waste and matrix.

Isothermal Crystallization Kinetics of Poly(ethylene oxide)/Poly(ethylene glycol)-g-silica Nanocomposites

In this work, the crystallization kinetics of poly(ethylene oxide) (PEO) matrix included with poly(ethylene glycol) (PEG) grafted silica (PEG-g-SiO2) nanoparticles and bare SiO2 were systematically investigated by differential scanning calorimetry (DSC) and polarized light optical microscopy (PLOM) method. PEG-g-SiO2 can significantly increase the crystallinity and crystallization temperature of PEO matrix under the non-isothermal crystallization process. Pronounced effects of PEG-g-SiO2 on the crystalline morphology and crystallization rate of PEO were further characterized by employing spherulitic morphological observation and isothermal crystallization kinetics analysis. In contrast to the bare SiO2, PEG-g-SiO2 can be well dispersed in PEO matrix at low P/N (P: Molecular weight of matrix chains, N: Molecular weight of grafted chains), which is a key factor to enhance the primary nucleation rate. In particular, we found that the addition of PEG-g-SiO2 slows the spherulitic growth fronts compared to the neat PEO. It is speculated that the interfacial structure of the grafted PEG plays a key role in the formation of nuclei sites, thus ultimately determines the crystallization behavior of PEO PNCs and enhances the overall crystallization rate of the PEO nanocomposites.

Melt Rheology and Mechanical Characteristics of Poly(Lactic Acid)/Alkylated Graphene Oxide Nanocomposites

Poly(lactic acid) (PLA) nanocomposites were synthesized by a solution blending and coagulation method using alkylated graphene oxide (AGO) as a reinforcing agent. Turbiscan confirmed that the alkylation of GO led to enhanced compatibility between the matrix and the filler. The improved dispersity of the filler resulted in superior interfacial adhesion between the PLA chains and AGO basal plane, leading to enhanced mechanical and rheological properties compared to neat PLA. The tensile strength and elongation at break, i.e., ductility, increased by 38% and 42%, respectively, at the same filler content nanocomposite (PLA/AGO 1 wt %) compared to nonfiller PLA. Rheological analysis of the nanocomposites in the molten state of the samples was performed to understand the filler network formed inside the matrix. The storage modulus increased significantly from PLA/AGO 0.5 wt % (9.6 Pa) to PLA/AGO 1.0 wt % (908 Pa). This indicates a percolation threshold between the two filler contents. A steady shear test was performed to examine the melt flow characteristics of PLA/AGO nanocomposites at 170 °C, and the viscosity was predicted using the Carreau-Yasuda model.

Study on Thermal Behavior of Some Biocompatible and Biodegradable Materials Based on Plasticized PLA, Chitosan, and Rosemary Ethanolic Extract

Thermal characterization of some multifunctional environmentally friendly materials based on plasticized poly (lactic acid) (PLA)/chitosan (CS) and rosemary extract (R) previously obtained is presented. Differential scanning calorimetry (DSC) associated with other complex investigations such as chemiluminescence and coupled thermogravimetry (TG)/Fourier-transform infrared spectroscopy (FT-IR)/mass spectroscopy (MS) was performed in order to test both the thermal behavior and the biocomposition–property relationship. It was established that the rosemary ethanolic extract offers an efficient protection against thermoxidative degradation to the new developed plasticized PLA-based biocomposites which show good thermal properties, being suitable for both medical and food packaging applications.

Enhancement of Gas Barrier Properties of Graphene Oxide/Poly (Lactic Acid) Films Using a Solvent-free Method

Graphene oxide(GO)/polylactic acid (PLA) nanocomposite, prepared using a solvent-free melt mixing processing, is investigated as a potential oxygen barrier packaging film in this work. In order to disperse GO homogeneously in PLA matrix, hydrophobic silane coupling agent, i.e., γ-(2,3-epoxypropoxy)propyltrimethoxysilane (KH560), is used to modify the graphene oxide sheets. The modified GO is able to be well bonded to the PLA due to the formation of covalent bonds between the epoxy groups of KH560 and the carboxyl and hydroxyl terminal groups of PLA. Furthermore, the thermal stability of GO is enhanced due to the long alkyl side chain of KH560, which could also increase the crystallinity of PLA. As a result, the crystallinity of PLA is significantly improved because of the linear KH560 chains, which can act as nucleating agents to improve the crystallization. The KH560-GO helps to reduce the O₂ permeability of KH560-GO/PLA composite films via a dual-action mechanism: (1) providing physical barrier due to their native barrier properties, and (2) by resulting in higher degree of crystallinity. The as-prepared KH560-GO0.75/PLA is able to exhibit ca. 33% and ca. 13% decrease in the P_O2 than the neat PLA and GO0.75/PLA film, respectively. Finally, the mechanical properties and impact fractured surfaces indicate that the increase in the tensile strength and elongation at break value of KH560-GO/PLA are due to the strong interfacial adhesion and the strong bonding between the epoxy group of KH560-GO and hydroxyl and carboxyl acid terminal groups of PLA matrix.

Polyethylene glycol grafted with carboxylated graphene oxide as a novel interface modifier for polylactic acid/graphene nanocomposites

Strength and toughness are both of great importance for the application of polylactic acid (PLA). Unfortunately, these two properties are often contradictory. In this work, an effective and practical strategy is proposed by using carboxylated graphene oxide (GC) grafted with polyethylene glycol (PEG), i.e. GC-g-PEG. The synthesis procedure of GC-g-PEG is firstly optimized. Then, a series of PLA nanocomposites were prepared by the melt blending method via masterbatch. In comparison to that achieved over pure PLA, these nanocomposites are of higher crystallinity, thermal stability and mechanical strength. This is mainly attributed to well-tailored interface and good dispersion. Especially, while retaining the tensile strength of the original PLA, the elongation at break increases by seven times by adding 0.3 wt% GC-g-PEG.

Pressure induced crystallization and in situ simultaneous SAXS/WAXS investigations on structure transitions

A phase diagram of PLLA crystal structures as a function of crystallization temperature (T_c) and pressure (P_c).

Poly(l-lactic acid)/Boron Nitride Nanocomposites: Influence of Boron Nitride Functionalization on the Properties of Poly(l-lactic acid)

Differently functionalized boron nitride nanosheets (BNNSs) [hydroxyl (OH_BNNSs), amine (NH₂_BNNSs), and poly(ethylene glycol) (PEG) (PEG_BNNSs)] were synthesized, and their effects on the structure and thermal properties of poly(l-lactic acid) (PLLA) along with those of the pristine BNNSs were studied. Highly dispersed nanocomposites were prepared using PLLA and 0.5 wt % of pristine/functionalized BNNSs via a solvent blending method. Homogeneous dispersion of BNNSs in the polymer matrix was confirmed using X-ray diffraction and scanning electron microscopy. Pristine BNNSs and OH_BNNSs accelerated the crystallization of PLLA as effective nucleating agents and favored the formation of the α form in melt-crystallized samples. On the other hand, NH₂_BNNSs and PEG_BNNSs incorporated samples result in the moderate crystallization rate of PLLA and lead to the formation of a mixture of α and α' forms similar to the PLLA. It is also found that thermal stability and thermal conductivity of PLLA nanocomposites significantly depend on the type of functionalization of BNNSs. At 0.5 wt % loading, the thermal conductivity enhancement is maximum for PEG_BNNSs incorporated PLLA (∼62%), and that is only 9% for pristine BNNSs incorporated PLLA. The thermal stability of PLLA nanocomposites was significantly improved by 32-41 °C depending on the type of functionalized BNNSs compared to PLLA. It is proposed that the strong interaction between functionalized BNNSs and PLLA matrix is responsible for the improved thermal management properties.

Effects of poly(ethylene glycol)-grafted graphene on the electrical properties of poly(lactic acid) nanocomposites

Maleic anhydride was reacted with the armchair edges of graphene nanosheets (GN) via Diels-Alder reaction. Then, polyethylene glycol (PEG) was grafted onto the GN in the presence of anhydride groups through an esterification reaction. The PEG-grafted GN (PEG-g-GN) was characterised via FTIR analysis, thermogravimetric analysis, scanning electron microscopy, Raman spectroscopy and contact angle measurements, proving that PEG was successfully grafted onto the GN surface. The results indicated that PEG-g-GN possessed high electrical conductivity and was dispersed in polylactic acid (PLA). The composites were fabricated by using PEG-g-GN and GN as the conductive agent in the PLA matrix. Owing to the function of PEG molecular chains, PEG-g-GN can be uniformly dispersed in the PLA matrix and improve the tensile strength of composites to 59.46 MPa and conductivity to 9.69 × 10-4 S cm-1 at a PEG-g-GN content of 1 wt%.

Hydrophobic Graphene Oxide as a Promising Barrier of Water Vapor for Regenerated Cellulose Nanocomposite Films

Regenerated cellulose (RC) films exhibit poor water barrier performance, which seriously restricts its applications. To address this issue, an impermeable and hydrophobic graphene oxide modified by chemically grafting octadecylamine (GO-ODA) was utilized to enhance the water vapor barrier performance of RC nanocomposite films. Compared to the neat RC film, more than 20% decrease in the coefficient of water vapor permeability (P _H2O) was achieved by loading only 2.0 wt % GO-ODA. The promising hydrophobicity of GO-ODA effectively retarded the formation of hydrogen bonding at the relatively weakened interface between GO and RC, compensating for the diffusion of water vapor molecules at the interface; on the other hand, the fully exfoliated GO-ODA nanosheets were inclined to align with the surface of the as-prepared RC nanocomposite films during hot-pressure drying, creating a much more tortuous pathway for diffusion of water molecules. The new insights could be valuable for widening application of cellulose such as packaging.

Nucleation Enhancement in Stereodefective Poly(l-lactide) by Free Volume Expansion Resulting from Low-Temperature Pressure CO₂ Preconditioning

Nucleation enhancement in a highly stereodefective poly(l-lactide) (PLLA) with an optical purity of 88% by low-temperature pressure (0 and 35 °C under 2 MPa) CO₂ preconditioning was investigated using differential scanning calorimetry (DSC), infrared (IR) spectroscopy, polarized optical microscopy (POM) as well as positron annihilation lifetime spectroscopy (PALS). Despite the preconditioning of the melt-quenched films for 2 h, IR results indicated that no trace of mesophase was generated and the samples remained in the glassy state. However, judging from the results of DSC, IR, and POM, when compared to the untreated sample, both the treated ones showed a significantly enhanced crystal nucleation effect, resulting in the corresponding greatly enhanced crystallization kinetics. Moreover, owing to the existence of the retrograde vitrification, the conditions of the previous low-pressure CO₂ conditioning affected the nucleation enhancement effect. When compared to the case of 35 °C, the much lower temperature of 0 °C was more effective for nucleation enhancement. The PALS results indicated that the enlarged free volume, which resulted from the CO₂ conditioning, largely accounted for the formation of locally ordered structures, providing many more potential nucleation sites for forming critical nuclei and thus the resulting enhanced crystallization kinetics in glassy PLLA. The present results have implications in understanding the nucleation enhancement effect, in particular in stereodefective PLLA systems, which possess extremely low crystallization ability and are thus probably too problematic to be evaluated by conventional methods.