Quantifying Carboxylic Acid Concentration in Model Polyamide Desalination Membranes via Fourier Transform Infrared Spectroscopy

Electrochemical genosensor based on RNA-responsive human telomeric G-quadruplex DNA: A proof-of-concept with SARS-CoV-2 RNA

In this report, a facile and label-free electrochemical RNA biosensor is developed by exploiting methylene blue (MB) as an electroactive positive ligand of G-quadruplex. The electrochemical response mechanism of the nucleic acid assay was based on the change in differential pulse voltammetry (DPV) signal of adsorbed MB on the immobilized human telomeric G-quadruplex DNA with a loop that is complementary to the target RNA. Hybridization between synthetic positive control RNA and G-quadruplex DNA probe on the transducer platform rendered a conformational change of G-quadruplex to double-stranded DNA (dsDNA), and increased the redox current of cationic MB π planar ligand at the sensing interface, thereby the electrochemical signal of the MB-adsorbed duplex is proportional to the concentration of target RNA, with SARS-CoV-2 (COVID-19) RNA as the model. Under optimal conditions, the target RNA can be detected in a linear range from 1 zM to 1 μM with a limit of detection (LOD) obtained at 0.59 zM for synthetic target RNA and as low as 1.4 copy number for positive control plasmid. This genosensor exhibited high selectivity towards SARS-CoV-2 RNA over other RNA nucleotides, such as SARS-CoV and MERS-CoV. The electrochemical RNA biosensor showed DPV signal, which was proportional to the 2019-nCoV_N_positive control plasmid from 2 to 200000 copies (R2 = 0.978). A good correlation between the genosensor and qRT-PCR gold standard was attained for the detection of SARS-CoV-2 RNA in terms of viral copy number in clinical samples from upper respiratory specimens.

Highly effective removal of perfluorooctanoic acid (PFOA) in water with DBD-plasma-enhanced rice husks

Adsorption is regarded as an efficient method to eliminate per- and polyfluoroalkyl substances from an aqueous solution. In the present investigation, an adsorbent based on rice husks (RHs) was successfully prepared by phosphoric acid (PA) activation and dielectric barrier discharge (DBD) plasma treatment, and it was used to adsorb perfluorooctanoic acid (PFOA) from water. The electrodes employed in the experiment were planar type. This research investigated RH surface properties and adsorption capacity before and after modification using DBD plasma. The results revealed that the He-O2 plasma modification introduced oxygen-containing functional groups and increased the PFOA removal efficiency. Increasing the oxygen content and total gas flow rate to 30 vol.% and 1.5 L/min, respectively, with 10 min of RH plasma treatment time at 100 W plasma discharge power enhanced the PFOA removal efficiency to 92.0%, while non-treated RH showed the removal efficiency of only 46.4%. The removal efficiency of the solution increased to 96.7% upon adjusting the pH to 4. The adsorption equilibrium isotherms fitted the Langmuir model, and the adsorption kinetic followed the pseudo-second-order model. The maximum adsorption capacity was 565 mg/g when the Langmuir isotherm model was applied.

Fluids and Electrolytes under Confinement in Single-Digit Nanopores

Confined fluids and electrolyte solutions in nanopores exhibit rich and surprising physics and chemistry that impact the mass transport and energy efficiency in many important natural systems and industrial applications. Existing theories often fail to predict the exotic effects observed in the narrowest of such pores, called single-digit nanopores (SDNs), which have diameters or conduit widths of less than 10 nm, and have only recently become accessible for experimental measurements. What SDNs reveal has been surprising, including a rapidly increasing number of examples such as extraordinarily fast water transport, distorted fluid-phase boundaries, strong ion-correlation and quantum effects, and dielectric anomalies that are not observed in larger pores. Exploiting these effects presents myriad opportunities in both basic and applied research that stand to impact a host of new technologies at the water-energy nexus, from new membranes for precise separations and water purification to new gas permeable materials for water electrolyzers and energy-storage devices. SDNs also present unique opportunities to achieve ultrasensitive and selective chemical sensing at the single-ion and single-molecule limit. In this review article, we summarize the progress on nanofluidics of SDNs, with a focus on the confinement effects that arise in these extremely narrow nanopores. The recent development of precision model systems, transformative experimental tools, and multiscale theories that have played enabling roles in advancing this frontier are reviewed. We also identify new knowledge gaps in our understanding of nanofluidic transport and provide an outlook for the future challenges and opportunities at this rapidly advancing frontier.

Antifungal efficiency and cytocompatibility of polymethyl methacrylate modified with zinc dimethacrylate

Objectives

Considering the high incidence rates of denture stomatitis, research that providing dental biomaterials with antifungal property are essential for clinical dentistry. The objectives of the present study were to investigate the effect of zinc dimethacrylate (ZDMA) modification on the antifungal and cytotoxic properties, as well as the variance in surface characteristics and other physicochemical properties of polymethyl methacrylate (PMMA) denture base resin.

Methods

PMMA with various mass fraction of ZDMA (1 wt%, 2.5 wt% and 5 wt%) were prepared for experimental groups, and unmodified PMMA for the control. Fourier-transform infrared spectroscopy (FTIR) was applied for characterization. Thermogravimetric analysis, atomic force microscopy and water contact angle were performed to investigate the thermal stability and surface characteristics (n=5). Antifungal capacities and cytocompatibility were evaluated with Candida albicans (C. albicans) and human oral fibroblasts (HGFs), respectively. Colony-forming unit counting, crystal violet assay, live/dead biofilm staining and scanning electron microscopy observation were performed to assess antifungal effects, and the detection of intracellular reactive oxygen species production was applied to explore the possible antimicrobial mechanism. Finally, the cytotoxicity of ZDMA modified PMMA resin was evaluated by the 3-(4,5-dimethyl-thiazol-2-yl)-2,5-diphenyl-tetrazolium bromide (MTT) assay and live/dead double staining.

Results

The FTIR analyses confirmed some variation in chemical bonding and physical blend of the composites. Incorporation of ZDMA significantly enhanced the thermal stability and hydrophilicity compared with unmodified PMMA (p < 0.05). The surface roughness increased with the addition of ZDMA while remained below the suggested threshold (≤ 0.2 µm). The antifungal activity significantly improved with ZDMA incorporation, and cytocompatibility assays indicated no obvious cytotoxicity on HGFs.

Conclusions

In the present study, the ZDMA mass fraction up to 5 wt% in PMMA performed better thermal stability, and an increase in surface roughness and hydrophilicity without enhancing microbial adhesion. Moreover, the ZDMA modified PMMA showed effective antifungal activity without inducing any cellular side effects.

Eugenol micro-emulsion reinforced with silver nanocomposite electrospun mats for wound dressing strategies

The fabricated eugenol microemulsion based silver nanoparticle nanofibers with effective antibacterial efficacy provide a suitable wound dressing strategy to develop an ideal skin tissue scaffold for the treatment of cut wounds in clinical practice.

Zwitterionic Hydrogel-Impregnated Membranes with Polyamide Skin Achieving Superior Water/Salt Separation Properties

Support-free nonporous membranes have emerged as a new material platform for osmotic pressure-driven processes due to its insusceptibility to internal concentration polarization (ICP). Herein, we demonstrate high-performance membranes of zwitterionic hydrogels impregnated in porous membranes with a skin layer of highly cross-linked polyamides on both sides prepared by gel-liquid interfacial polymerization (GLIP). Such a configuration eliminates the pores and thus ICP, while the thin polyamide layer provides high salt rejection but negligible resistance to the water transport compared with the hydrogels. The polyamide skin layers are characterized using scanning electron microscopy and atomic force microscopy. The effect of the hydrogel compositions and polyamide formation conditions on the water/salt separation properties is thoroughly investigated. Example membranes show water permeance and salt rejection comparable to state-of-the-art commercial forward osmosis membranes and essentially no ICP.

Water-polyamide chemical interplay in desalination membranes explored by ambient pressure X-ray photoelectron spectroscopy

Reverse osmosis using aromatic polyamide membranes is currently the most important technology for seawater desalination. The performance of reverse osmosis membranes is highly dependent on the interplay of their surface chemical groups with water and water contaminants. In order to better understand the underlying mechanisms of these membranes, we study ultrathin polyamide films that chemically resemble reverse osmosis membranes, using ambient pressure X-ray photoelectron spectroscopy. This technique can identify the functional groups at the membrane-water interface and allows monitoring of small shifts in the electron binding energy that indicate interaction with water. We observe deprotonation of free acid groups and formation of a 'water complex' with nitrogen groups in the polymer upon exposure of the membrane to water vapour. The chemical changes are reversed when water is removed from the membrane. While the correlation between functional groups and water uptake is an established one, this experiment serves to understand the nature of their chemical interaction, and opens up possibilities for tailoring future materials to specific requirements.

Monitoring the Interfacial Polymerization of Piperazine and Trimesoyl Chloride with Hydrophilic Interlayer or Macromolecular Additive by In Situ FT-IR Spectroscopy

The interfacial polymerization (IP) of piperazine (PIP) and trimesoyl chloride (TMC) has been extensively utilized to synthesize nanofiltration (NF) membranes. However, it is still a huge challenge to monitor the IP reaction, because of the fast reaction rate and the formed ultra-thin film. Herein, two effective strategies were applied to reduce the IP reaction rate: (1) the introduction of hydrophilic interlayers between the porous substrate and the formed polyamide layer, and (2) the addition of macromolecular additives in the aqueous solution of PIP. As a result, in situ Fourier transform infrared (FT-IR) spectroscopy was firstly used to monitor the IP reaction of PIP/TMC with hydrophilic interlayers or macromolecular additives in the aqueous solution of PIP. Moreover, the formed polyamide layer growth on the substrate was studied in a real-time manner. The in situ FT-IR experimental results confirmed that the IP reaction rates were effectively suppressed and that the formed polyamide thickness was reduced from 138 ± 24 nm to 46 ± 2 nm according to TEM observation. Furthermore, an optimized NF membrane with excellent performance was consequently obtained, which included boosted water permeation of about 141-238 (L/m2·h·MPa) and superior salt rejection of Na2SO4 > 98.4%.

Quantitative Characterization of a Desalination Membrane Model System by X-ray Photoelectron Spectroscopy

Aromatic polyamide films form the active layer in reverse osmosis desalination membranes. Despite widespread use of this technology, it suffers from low rejection rates for certain water contaminants and from membrane fouling. Through a better understanding of the fundamental surface chemical processes during reverse osmosis desalination, advances in membrane and material design are expected. The recent invention of a molecular layer-by-layer (mLbL) preparation technique [ Johnson , P. M. ; Molecular Layer-by-Layer Deposition of Highly Crosslinked Polyamide Films . J. Polym. Sci., Part B: Polym. Phys. 2012 , 50 ( 3 ), 168 - 173 ] yields films that are sufficiently smooth to warrant investigation with high-resolution microscopy and spectroscopy methods. We present high-resolution, quantitative X-ray photoelectron spectroscopy (XPS) data on the surface chemistry of ultrathin polyamide films that can serve as a model system for desalination membranes. We show that a quantitative analysis of the XPS spectra gives information about the functional groups of the film as well as other compounds present due to the synthesis under ambient conditions. Unpolymerized functional groups are identified and aid in understanding the degree of cross-linking. Investigation of polymers with synchrotron-based XPS requires taking beam-induced changes into account. We quantify X-ray beam damage and show that beam damage to the polyamide is limited, allowing long-term investigation of thin polyamide films. Characterizing mLbL-grown films via high-resolution XPS is the basis for a better understanding of the chemical interplay of polyamide surface functional groups with the major components of desalination systems.

Characterizing salt permeability in polyamide desalination membranes using electrochemical impedance spectroscopy

Improving the performance of desalination membranes requires better measurements of salt permeability in the polyamide separating layer to elucidate the thermodynamic and kinetic components of membrane permselectivity. In this work, electrochemical impedance spectroscopy (EIS) is introduced as a technique to measure the salt permeability and estimate the salt partition coefficient in thin polyamide films created using molecular layer-by-layer deposition. The impedance of supported polyamide films ranging in thickness from 3.5 nm to 28.5 nm were measured in different electrolyte solutions. Impedance spectra were modeled with equivalent circuits containing resistive and capacitive elements associated with the EIS measurement system as well as characteristic low-frequency parallel resistive and capacitive elements that are associated with the polyamide film. The characteristic polyamide membrane resistance increases with film thickness, decreases with solution concentration, and is an order of magnitude greater for a divalent cationic solution than for a monovalent cationic solution. For each polyamide film, salt permeability is calculated from the membrane resistance, and a salt partition coefficient is estimated. At the highest solution concentration measured, which is representative of brackish water desalination conditions, the calculated salt permeabilities range from P _s = 1.3 × 10^-16 m s^-1 to 3.9 × 10^-16 m s^-1, and the estimated salt partition coefficients range from K _s = 0.008 to 0.016. These measurements demonstrate that EIS is a powerful tool for studying membrane permselectivity through the measurement of salt permeability in thin polyamide films.

Thermal treatment of flame retardant plastics: A case study on a waste TV plastic shell sample

In this work, the combustion and pyrolysis characteristics of a waste TV plastic shell sample were investigated using a powerful Thermogravimetric-Fourier Infrared Spectrum-Mass Spectrum (TG-FTIR-MS) technique. The decomposition mechanisms of plastic waste and fate of bromines in both thermal processes were probed as well. The TG analysis revealed that the combustion rate was larger than that of pyrolysis at temperature of 456 °C below, whereas it decreased at temperature of 456-605 °C. As a result, the total weight loss was equivalent at temperature of 605 °C for both processes. The FTIR analysis indicated the plastic combusted vigorously at 300-500 °C and 800-900 °C. As a comparison, it decomposed drastically at 300-400 °C and 500-900° in pyrolysis. The MS analysis showed that the release of brominated products HBr, CH₃Br, C₂H₅Br, C₃H₅Br, C₃H₇Br and C₃H₅BrO increased with an increase of temperature and reached maximum at 400-600 °C in both thermal processes. The release intensities of larger molecules C₆H₅Br, C₆H₅BrO and C₆H₄Br₂ were in the descending order of C₆H₅Br > C₆H₄Br₂ > C₆H₅BrO. It was not significant in the evolved products and decomposition pathway for both thermal processes. The entire decomposition of TV plastic shell sample could be divided into three stages, taking account of the evolved products. The backbone in acrylonitrile butadiene styrene resin and tetrabromobisphenol A first broke at 350 °C below, resulting in the form of 2-bromophenol, styrene, acrylonitrile and polybutadiene. Subsequently, the resulted 2-bromophenol debrominated forming HBr, which further reacted with hydrocarbons resulting in various brominated derivates. In addition, many small molecules, including CO₂, CO and CH₄ were generated in this stage. Further increasing temperature to 550 °C above, larger brominated derivates decomposed and smaller molecules predominated.