Efficient Pure Blue Light-Emitting Diodes Based on CsPbBr3 Quantum-Confined Nanoplates

Monoammonium Modified Dion-Jacobson Quasi-2D Perovskite for High Efficiency Pure-Blue Light Emitting Diodes

Quasi-2D perovskites exhibit impressive optoelectronic properties and hold significant promise for future light-emitting devices. However, the efficiency of perovskite light-emitting diodes (PeLEDs) is seriously limited by defect-induced nonradiative recombination and imbalanced charge injection. Here, the defect states are passivated and charge injection balance is effectively improved by introducing the additive cyclohexanemethylammonium (CHMA) to bromide-based Dion-Jacobson (D-J) structure quasi-2D perovskite emission layer. CHMA participates in the crystallization of perovskite, leading to high quality film composed of compact and well-contacted grains with enhanced hole transportation and less defects. As a result, the corresponding PeLEDs exhibit stable pure blue emission at 466 nm with a maximum external quantum efficiency (EQE) of 9.22%. According to current knowledge, this represents the highest EQE reported for pure-blue PeLEDs based on quasi-2D bromide perovskite thin films. These findings underscore the potential of quasi-2D perovskites for advanced light-emitting devices and pave the way for further advancements in PeLEDs.

Blade-coated perovskite nanoplatelet polymer composites for sky-blue light-emitting diodes

Colloidal perovskite nanoplatelets (NPLs) have shown promise in tackling blue light-emitting diode challenges based on their tunable band gap and high photoluminescence efficiencies. However, high quality and large area dense NPL films have been proven to be very hard to prepare because of their chemical and physical fragility during the liquid phase deposition. Herein, we report a perovskite-polymer composite film deposition strategy with fine morphology engineering obtained using the blade coating method. The effects of the polymer type, solution concentration, compounding ratio and film thickness on the film quality are systematically investigated. We found that a relatively high-concentration suspension with an optimized NPL to polymer ratio of 1 : 2 is crucial for the suppression of phase separation and arriving at a uniform film. Finally, sky-blue NPL-based perovskite light-emitting diodes were fabricated by blade coating showing an EQE of 0.12% on a device area of 16 mm2.

Nickel Oxide Hole Injection Layers for Balanced Charge Injection in Quantum Dot Light-Emitting Diodes

Quantum dot (QD) light-emitting diodes (QLEDs) are promising for next-generation displays, but suffer from carrier imbalance arising from lower hole injection compared to electron injection. A defect engineering strategy is reported to tackle transport limitations in nickel oxide-based inorganic hole-injection layers (HILs) and find that hole injection is able to enhance in high-performance InP QLEDs using the newly designed material. Through optoelectronic simulations, how the electronic properties of NiOx affect hole injection efficiency into an InP QD layer, finding that efficient hole injection depends on lowering the hole injection barrier and enhancing the acceptor density of NiOx is explored. Li doping and oxygen enriching are identified as effective strategies to control intrinsic and extrinsic defects in NiOx, thereby increasing acceptor density, as evidenced by density functional theory calculations and experimental validation. With fine-tuned inorganic HIL, InP QLEDs exhibit a luminance of 45 200 cd m-2 and an external quantum efficiency of 19.9%, surpassing previous inorganic HIL-based QLEDs. This study provides a path to designing inorganic materials for more efficient and sustainable lighting and display technologies.

Enhanced Efficiency and Stability of Sky Blue Perovskite Light-Emitting Diodes via Introducing Lead Acetate

All-inorganic metal halide perovskite is promising for highly efficient and thermally stable perovskite light-emitting diodes (PeLEDs). However, there is still great room for improvement in the film quality, including low coverage and high trap density, which play a vital role in achieving high-efficiency PeLEDs. In this work, lead acetate (Pb(Ac)2) was introduced into the perovskite precursor solution as an additive. Experimental results show that perovskite films deposited from a one-step anti-solvent free solution process with increased surface coverage and reduced trap density were obtained, leading to enhanced photoluminescence (PL) intensity. More than that, the valence band maximum (VBM) of perovskite films was reduced, bringing about a better energy level matching the work function of the hole-injection layer (HIL) poly (3,4-ethylenedioxythiophene)-poly (styrene sulfonate) (PEDOT: PSS), which is facilitated for the hole injection, leading to a decrease in the turn-on voltage (Vth) of PeLEDs from 3.4 V for the control device to 2.6 V. Finally, the external quantum efficiency (EQE) of the sky blue PeLEDs (at 484 nm) increased from 0.09% to 0.66%. The principles of Pb(Ac)2 were thoroughly investigated by using X-ray photoelectron spectroscopy (XPS) and Fourier transform infrared spectroscopy (FTIR). This work provides a simple and effective strategy for improving the morphology of perovskite and therefore the performance of PeLEDs.

Z-Type Ligand Enables Efficient and Stable Deep-Blue Perovskite Light-Emitting Diodes

During the synthesis of deep-blue perovskite quantum dots (PQDs), they generally emerge as a two-dimensional byproduct with poor yield and low photoluminescence quantum yield (PLQY) due to amine ligand enrichment-induced abundant surface defects. Herein, we provide a colloidal synthesis method to prepare deep-blue CsPbBr3 PQDs in a green nontoxic solvent via strategic Z-type ligand engineering. Z-type ligands of zinc octanoate enable the formation of robust coordination bonds with surface bromide ions of PQDs, maintaining acid-base equilibrium and reducing excess amine enrichment on the PQDs surface. Consequently, homogeneous and monodispersed PQDs with improved PLQY of 73% are successfully synthesized, achieving efficient deep-blue LEDs with a peak EQE of 5.46%, a maximum luminance of 847.6 cd/m2, and an operational half-lifetime of 14 min. The devices exhibit color coordinates of (0.137, 0.049), closely approximating the Rec. 2020 blue standard. Our work offers a potentially eco-friendly and viable route for realizing high-performance LEDs in the deep-blue region.

Two-dimensional Cs3Sb2Br9 inducing transformation of three-dimensional CsPbBr3 to nanoplates

This communication describes an effective morphological control strategy involving introducing two-dimensional (2D) Cs3Sb2Br9 to induce a transformation of three-dimensional (3D) CsPbBr3 to 2D nanoplates (NPLs). By tuning the Sb/Pb ratio, 2D CsPbBr3 NPLs exhibiting a deep-blue emission centered at a wavelength of 464 nm with an FWHM of 24 nm have been produced. The absence of organic ligands in these high-quality 2D NPLs mitigate the instability issue induced by organic ligand migration and penetration, and these NPLs exhibit 80% of the initial PL intensity after 55 days.

Ultrastable Photodetectors Based on Blue CsPbBr3 Perovskite Nanoplatelets via a Surface Engineering Strategy

Recently, photodetectors based on perovskite nanoplatelets (NPLs) have attracted considerable attention in the visible spectral region owing to their large absorption cross-section, high exciton binding energy, excellent charge transfer properties, and appropriate flexibility. However, their stability and performance are still challenging for perovskite NPL photodetectors. Here, a surface engineering strategy to enhance the optical stability of blue-light CsPbBr3 NPLs by acetylenedicarboxylic acid (ATDA) treatment has been developed. ATDA has strong binding capacity and a short chain length, which can effectively passivate defects and significantly improve the photoluminescence quantum efficiency, stability, and carrier mobility of NPLs. As a result, ATDA-treated CsPbBr3 NPLs exhibit improved optical properties in both solutions and films. The NPL solution maintains high PL performance even after being heated at 80 °C for 2 h, and the NPL film remains nondegradable after 4 h of exposure to ultraviolet irradiation. Especially, photodetectors based on the treated CsPbBr3 NPL films demonstrate exceptional performance, especially when the detectivity approaches up to 9.36 × 1012 Jones, which can be comparable to the best CsPbBr3 NPL photodetectors ever reported. More importantly, the assembled devices demonstrated high stability (stored in an air environment for more than 30 days), significantly exceeding that of untreated NPLs.

Energy transfer enhanced photoluminescence of 2D/3D CsPbBr3 hybrid assemblies

Energy transfer has been proven to be an effective method to optimize optoelectronic conversion efficiency by improving light absorption and mitigating nonradiative losses. We prepared 2D/3D CsPbBr3 hybrid assemblies at different reaction temperatures using the hot injection method and found that the photoluminescence quantum yields (PLQYs) of these hybrids were greatly enhanced from 53.4% to 72.57% compared with 3D nanocrystals (NCs). Femtosecond transient absorption measurements were used to study the PLQY enhancement mechanisms, and it was found that the hot carrier lifetime improved from 0.36 to 1.88 ps for 2D/3D CsPbBr3 hybrid assemblies owing to the energy transfer from 2D nanoplates to 3D NCs. The energy transfer benefits the excited carrier accumulation and prolonged hot carrier lifetime in 3D NCs in hybrid assemblies, as well as PLQY enhancement in materials.

Stable deep-blue FAPbBr3 quantum dots facilitated by amorphous metal halide matrices

This communication describes a strategy to synthesize stable deep blue FAPbBr3 quantum dots (QDs) by constructing a matrix structure. Amorphous Ni2+-based metal halide matrices can stabilize QDs from both chemical and physical factors, and Ni2+ doping can further enhance their structural stability due to lattice shrinking. Such deep blue QD films exhibit stable X-ray diffraction patterns and photoluminescence even after 245 days of storage.

One-Step Ultrasonic Preparation of Stable Bovine Serum Albumin-Perovskite for Fluorescence Analysis of L-Ascorbic Acid and Alkaline Phosphatase

Halide lead perovskite has attracted increased attention due to its excellent optical properties. However, the poor stability of the halide lead perovskite nanocrystals has been a major obstacle to their application in biosensing. Here, we proposed a method to synthesize CsPbBr3/BSA NCs perovskite using bovine serum albumin (BSA) as a zwitterion ligand. Then, a fluorescent sensor for alkaline phosphatase determination based on CsPbBr3/BSA NCs was successfully built via the interaction of L-ascorbic acid (AA) with BSA on the perovskite surface. Under optimal conditions, the sensor showed a linear concentration range from 50 to 500 μM with a detection limit of 28 μM (signal-to-noise ratio of 3) for AA, and demonstrated a linear concentration range from 40 to 500 U/L with a detection limit of 15.5 U/L (signal-to-noise ratio of 3) for alkaline phosphatase (ALP). In addition, the proposed fluorescent biosensor exhibited good selectivity and recovery in the determination of ALP in human serum. This strategy offers an innovative way for enhancing the water stability of lead halide perovskite and promoting their application in biosensing areas.

Multidentate Ligand-Passivated CsPbI3 Perovskite Nanocrystals for Stable and Efficient Red-Light-Emitting Diodes

CsPbI₃ nanocrystals (NCs) have become a research hot spot in the field of light-emitting diodes (LEDs). Whereas, the long chain ligands with weak affinity to CsPbI₃ NCs have prevented their further development and commercialization. Herein, a novel multidentate short ligand tetramethylthiuram disulfide (TMTD) was employed via a ligand exchange process to enhance hole mobility and decrease trap density of the CsPbI₃ NCs film. Therefore, TMTD passivated CsPbI₃ NCs LED exhibited 20.65% maximum external quantum efficiency and 3861 cd/m² maximum luminance. Furthermore, TMTD passivated CsPbI₃ NCs LED exhibited good operational stability with a 128 min half-lifetime. This strategy using multidentate short ligand passivation provides an effective way to promote perovskite LED development and commercialization.

All-inorganic lead halide perovskite nanocrystals applied in advanced display devices

Advanced display devices are in greater demand due to their large color gamut, high color purity, ultrahigh visual resolution, and small size pixels. All-inorganic lead halide perovskite (AILHP) nanocrystals (NCs) possess inherent advantages such as narrow emission width, saturated color, and flexible integration, and have been developed as functional films, light sources, backlight components, and display panels. However, some drawbacks still restrict the practical application of advanced display devices based on AILHP NCs, including working stability, large-scale synthesis, and cost. In this review, we focus on AILHP NCs, review the recent progress in materials synthesis, stability improvement, patterning techniques, and device application. We also highlight the important role of materials systems in creating advanced display devices, followed by the challenges and opportunities in industrial processes. This review provides beneficial inspiration for the future development of AILHP NCs in colorful and white backlight, as well as high resolution full-color displays.

Eliminating Nanocrystal Surface Light Loss and Ion Migration to Achieve Bright Mixed-Halide Blue Perovskite LEDs

Blue light-emittin g diodes (LEDs) are important components for perovskite electroluminescence applications, which still suffer from insufficient luminescence efficiency and poor stability. In Cl/Br mixed perovskite NCs, surficial defects cause severe light failure and ion migration, the in-depth mechanism of which is also not clear. To gain insights into these issues, we employ the ligand post-addition approach for mixed Cl/Br NCs by using octylammonium hydrobromide (OctBr) ligands, which effectively decrease surficial light loss and block ion migration pathways. The passivated CsPbCl_1.5Br_1.5 NCs exhibit exceptional blue emission with 95% PLQY, and the electroluminescence spectra of LEDs are located at the initial positions at the initial states. The treated NC blue devices show a negligible color shift as the voltage increases, which proves that electric-field-driven ion migration is drastically suppressed. In addition, OctBr-treated CsPbCl_1.5Br_1.5 and CsPbClBr₂ NC LEDs show high external quantum efficiencies of 2.42 and 3.05% for emission peaks at 456 and 480 nm, respectively. Our work identified the nature of NC surface defects and provided a surficial modification approach to develop high-performance and color-stable blue mixed-halide perovskite LEDs.

Patterning Perovskite Quantum Dots Using Photopolymerization

All-inorganic cesium lead halide perovskite quantum dots (QDs) have several potential applications, owing to their unique optical and electronic properties. However, patterning perovskite QDs using conventional methods is difficult because of the ionic nature of QDs. Here, we demonstrate a unique approach, in which perovskite QDs are patterned in polymer films through the photocuring of monomers under patterned light illumination. The pattern illumination creates the transient polymer concentration difference, which drives the QDs to form patterns; hence controlling polymerization kinetics is essential for the generation of the QD pattern. For the patterning mechanism, a light projection system equipped with a digital micromirror device (DMD) is developed; thus, light intensity, an important factor to determine polymerization kinetics, is precisely controlled per position on the photocurable solution, resulting in the understanding of the mechanism and the formation of distinct QD patterns. The demonstrated approach assisted by the DMD-equipped projection system can form desired perovskite QD patterns solely by patterned light illumination, paving the way for the development of patterning methods for perovskite QDs and other nanocrystals.

Full-color micro-LED display with photo-patternable and highly ambient-stable perovskite quantum dot/siloxane composite as color conversion layers

In this paper, we successfully fabricated color conversion layers (CCLs) for full-color-mico-LED display using a perovskite quantum dot (PQD)/siloxane composite by ligand exchanged PQD with silane composite followed by surface activation by an addition of halide-anion containing salt. Due to this surface activation, it was possible to construct the PQD surface with a silane ligand using a non-polar organic solvent that does not damage the PQD. As a result, the ligand-exchanged PQD with a silane compound exhibited high dispersibility in the siloxane matrix and excellent atmospheric stability due to sol-gel condensation. Based on highly ambient stable PQD/siloxane composite based CCLs, full-color micro-LED display has a 1 mm pixel pitch, about 25.4 pixels per inch (PPI) resolution was achieved. In addition, due to the thin thickness of the black matrix to prevent blue light interference, the possibility of a flexible display that can be operated without damage even with a bending radius of 5 mm was demonstrated.

All-Inorganic Perovskite Quantum Dot-Based Blue Light-Emitting Diodes: Recent Advances and Strategies

Light-emitting diodes (LEDs) based on all-inorganic lead halide perovskite quantum dots (PQDs) have undergone rapid development especially in the past five years, and external quantum efficiencies (EQEs) of the corresponding green- and red-emitting devices have exceeded 23%. However, the blue-emitting devices are facing greater challenges than their counterparts, and their poor luminous efficiency has hindered the display application of PQD-based LEDs (PeQLEDs). This review focuses on the key challenges of blue-emitting PeQLEDs including low EQEs, short operating lifetime, and spectral instability, and discusses the essential mechanism by referring to the latest research. We then systematically summarize the development of preparation methods of blue emission PQDs, as well as the current strategies on alleviating the poor device performance involved in composition engineering, ligand engineering, surface/interface engineering, and device structural engineering. Ultimately, suggestions and outlooks are proposed around the major challenges and future research direction of blue PeQLEDs.

What Happens at Surfaces and Grain Boundaries of Halide Perovskites: Insights from Reactive Molecular Dynamics Simulations of CsPbI3

The commercialization of perovskite solar cells is hindered by the poor long-term stability of the metal halide perovskite (MHP) light-absorbing layer. Solution processing, the common fabrication method for MHPs, produces polycrystalline films with a wide variety of defects, such as point defects, surfaces, and grain boundaries. Although the optoelectronic effects of such defects have been widely studied, the evaluation of their impact on the long-term stability remains challenging. In particular, an understanding of the dynamics of degradation reactions at the atomistic scale is lacking. In this work, using reactive force field (ReaxFF) molecular dynamics simulations, we investigate the effects of defects, in the forms of surfaces, surface defects, and grain boundaries, on the stability of the inorganic halide perovskite CsPbI₃. Our simulations establish a stability trend for a variety of surfaces, which correlates well with the occurrence of these surfaces in experiments. We find that a perovskite surface degrades by progressively changing the local geometry of PbI_x octahedra from corner- to edge- to face-sharing. Importantly, we find that Pb dangling bonds and the lack of steric hindrance of I species are two crucial factors that induce degradation reactions. Finally, we show that the stability of these surfaces can be modulated by adjusting their atomistic details, by either creating additional point defects or merging them to form grain boundaries. While in general additional defects, particularly when clustered, have a negative impact on the material stability, some grain boundaries have a stabilizing effect, primarily because of the additional steric hindrance.

Healthy and stable lighting via single-component white perovskite nanoplates

Single-component healthy white light was achieved via Mn²⁺ post-doping into blue perovskite nanoplates (NPLs). The white light consists of two complementary colors, sky-blue (482 nm) and orange-red (610 nm), without harmful deep blue light (400-450 nm), which realizes the Commission Internationale de I'Eclairage (CIE) coordinates of (0.33, 0.33) (standard pure white light) and a color temperature of 6000 K. Benefitting from the lattice shrinking via Mn²⁺ doping, the stability of white NPLs toward long-term storage, UV light, heat, and polar solvents was greatly improved. Finally, a healthy and stable white light-emitting diode (WLED) was fabricated via down-conversion of a UV light LED with our white perovskite NPLs, and the WLED worked continuously for 240 minutes with a color drift of only (±0.006, ±0.004) and with a half lifetime (T₅₀) of 212 minutes.

Environmentally Friendly Syntheses of Self-Healed and Printable CsPbBr3 Nanocrystals

Generally, solvents used to synthesize perovskite NCs are toxic, which leads to waste liquid pollution and environmental degradation. Herein, we developed a novel environmentally friendly polar solvent method to synthesize CsPbBr₃ nanocrystals (NCs). Over 65% photoluminescence quantum yield (PLQYs) for NCs could be maintained over 45-850 h of storage time, and a maximum was 78% at 750 h. Such amazing stability in polar solvents is dominated by a ripening process, which heals surface defects. Additionally, their solid films also exhibited good moisture stability. Furthermore, CsPbBr₃ NCs were applied to inkjet-printing to prepare high-quality patterned films.

Facile synthesis of Mn2+ doped ultrathin (n=2) NPLs and their application to anti-counterfeiting

Ultrathin 2D perovskite nanoplatelets (NPLs) have many excellent optical properties including narrow absorption and emission spectra and large exciton binding energies. Doping Mn2+ into perovskite NPLs also introduces strong orange...