Mimicking a Dog's Nose: Scrolling Graphene Nanosheets

Ultrahigh humidity-resistance ppb-level formaldehyde sensing at room temperature induced by fluorinated dipole based "umbrella" and "bridge"

Formaldehyde (HCHO) is a major indoor pollutant that is extremely harmful to human health even at ppb-level. Meanwhile, ppb-level HCHO is also a potential disease marker in the exhalation of patients with respiratory diseases. Higher humidity resistance and lower practical limit of detection (pLOD) both have to be pursued for practical HCHO sensors. In this work, by assembling indium oxide (In2O3) and fluorinated dipole modified reduced graphene oxide (rGO), we prepared a high-performance room temperature HCHO sensor (In2O3 @ATQ-rGO). Excellent sensing properties toward HCHO under visible illumination have been achieved, including ultra-low pLOD of 3 ppb and high humidity-resistance. By control experiments and density functional theory calculation, it is indicated that the introduced fluorinated dipoles act as not only an "umbrella" to improve the humidity resistance of the composite, but also a "bridge" to accelerate the electron transport, improving the sensitivity of the material. The significant practicality and reliability of the obtained sensors were verified by in-situ simulation experiments using a 3 m3 test chamber with a humidity control system and by detection of the simulated lung disease patient's exhalation. This work provides an effective strategy of simultaneously achieving high humidity-resistance and low pLOD of room temperature formaldehyde sensing materials.

Bioinspired multi-scale interface design for wet gas sensing based on rational water management

Natural organisms have evolved multi-scale wet gas sensing interfaces with optimized mass transport pathways in biological fluid environments, which sheds light on developing artificial counterparts with improved wet gas sensing abilities and practical applications. Herein, we highlighted current advances in wet gas sensing taking advantage of optimized mass transport pathways endowed by multi-scale interface design. Common moisture resistance (e.g., employing moisture resistant sensing materials, post-modifying moisture resistant coatings, physical heating for moisture resistance, and self-removing hydroxyl groups) and moisture absorption (e.g., employing moisture absorption sensing materials and post-modifying moisture absorption coatings) strategies for wet gas sensing were discussed. Then, the design principles of bioinspired multi-scale wet gas sensing interfaces were provided, including macro-level condensation mediation, micro/nano-level transport pathway adjustment and molecular level moisture-proof design. Finally, perspectives on constructing bioinspired multi-scale wet gas sensing interfaces were presented, which will not only deepen our understanding of the underlying principles, but also promote practical applications.

The Future of Graphene: Preparation from Biomass Waste and Sports Applications

At present, the main raw material for producing graphene is graphite ore. However, researchers actively seek alternative resources due to their high cost and environmental problems. Biomass waste has attracted much attention due to its carbon-rich structure and renewability, emerging as a potential raw material for graphene production to be used in sports equipment. However, further progress is required on the quality of graphene produced from waste biomass. This paper, therefore, summarizes the properties, structures, and production processes of graphene and its derivatives, as well as the inherent advantages of biomass waste-derived graphene. Finally, this paper reviews graphene's importance and application prospects in sports since this wonder material has made sports equipment available with high-strength and lightweight quality. Moreover, its outstanding thermal and electrical conductivity is exploited to prepare wearable sensors to collect more accurate sports data, thus helping to improve athletes' training levels and competitive performance. Although the large-scale production of biomass waste-derived graphene has yet to be realized, it is expected that its application will expand to various other fields due to the associated low cost and environmental friendliness of the preparation technique.

Polyethylene glycol embedded reduced graphene oxide supramolecular assemblies for enhanced room-temperature gas sensors

Herein, we present the gas-dependent electrical properties of a reduced graphene oxide nanocomposite. The reduced graphene oxide (rGO) was synthesized by reducing GO with sodium borohydride (NaBH4). As-synthesized rGO was dispersed in DI water containing 1, 2, 3, 4, and 5 wt% polyethylene glycol (PEG) to prepare PEG-rGO supramolecular assemblies. The successful preparation of supramolecular assemblies was verified by their characterization using XRD, FESEM, EDS, TEM, FTIR, and Raman spectroscopy. At room temperature, the gas-dependent electrical properties of these supramolecular assemblies were investigated. The results showed that sensors composed of PEG-rGO supramolecular assemblies performed better against benzene and methanol at 3% and 4% PEG, respectively. However, high selectivity and a wide range of activation energies (∼1.64-1.91 eV) were observed for H2 gas for 4% PEG-modified supramolecular assemblies. The PEG-rGO supramolecular assemblies may be an excellent candidate for constructing ultrahigh-performance gas sensors for a variety of applications due to their high sensitivity and selectivity.

Recent Advances of Graphene Quantum Dots in Chemiresistive Gas Sensors

Graphene quantum dots (GQDs), as 0D graphene nanomaterials, have aroused increasing interest in chemiresistive gas sensors owing to their remarkable physicochemical properties and tunable electronic structures. Research on GQDs has been booming over the past decades, and a number of excellent review articles have been provided on various other sensing principles of GQDs, such as fluorescence-based ion-sensing, bio-sensing, bio-imaging, and electrochemical, photoelectrochemical, and electrochemiluminescence sensing, and therapeutic, energy and catalysis applications. However, so far, there is no single review article on the application of GQDs in the field of chemiresistive gas sensing. This is our primary inspiration for writing this review, with a focus on the chemiresistive gas sensors reported using GQD-based composites. In this review, the various synthesized strategies of GQDs and its composites, gas sensing enhancement mechanisms, and the resulting sensing characteristics are presented. Finally, the current challenges and future prospects of GQDs in the abovementioned application filed have been discussed for the more rational design of advanced GQDs-based gas-sensing materials and innovative gas sensors with novel functionalities.

Scrolling reduced graphene oxides to induce room temperature magnetism via spatial coupling of defects

Due to its intriguing features and numerous applications, graphene has garnered a lot of interest in recent years. However, it is still very difficult to create graphene-based room-temperature magnets without transition metals or rare earth elements since pristine graphene is inherently diamagnetic due to the delocalized π bonding network. Herein, room-temperature ferromagnetism with a saturation magnetization of 0.93 emu g-1 (300 K) is achieved in defect-rich-reduced graphene oxide (DR-rGO) nanoscrolls by creating a spatial coupling of defects. The experiments and DFT calculations verify that spatial coupling of defects could enhance Rudermann-Kittel-Kasuya-Yosida interactions to induce magnetism in graphene. It displays high-efficiency electromagnetic wave absorption performance with a minimal reflection loss of -62.1 dB and an effective absorption bandwidth of 7.8 GHz (3.0 mm) thanks to greatly improved magnetism. This breakthrough serves as a building block for the creation of room-temperature magnetic carbon materials and expands their applications in many pertinent domains.

Semiconducting MOFs on ultraviolet laser-induced graphene with a hierarchical pore architecture for NO2 monitoring

Due to rapid urbanization worldwide, monitoring the concentration of nitrogen dioxide (NO₂), which causes cardiovascular and respiratory diseases, has attracted considerable attention. Developing real-time sensors to detect parts-per-billion (ppb)-level NO₂ remains challenging due to limited sensitivity, response, and recovery characteristics. Herein, we report a hybrid structure of Cu₃HHTP₂, 2D semiconducting metal-organic frameworks (MOFs), and laser-induced graphene (LIG) for high-performance NO₂ sensing. The unique hierarchical pore architecture of LIG@Cu₃HHTP₂ promotes mass transport of gas molecules and takes full advantage of the large surface area and porosity of MOFs, enabling highly rapid and sensitive responses to NO₂. Consequently, LIG@Cu₃HHTP₂ shows one of the fastest responses and lowest limit of detection at room temperature compared with state-of-the-art NO₂ sensors. Additionally, by employing LIG as a growth platform, flexibility and patterning strategies are achieved, which are the main challenges for MOF-based electronic devices. These results provide key insight into applying MOFtronics as high-performance healthcare devices.

Large-Area and Visible-Light-Driven Heterojunctions of In2O3/Graphene Built for ppb-Level Formaldehyde Detection at Room Temperature

Achieving convenient and accurate detection of indoor ppb-level formaldehyde is an urgent requirement to ensure a healthy working and living environment for people. Herein, ultrasmall In₂O₃ nanorods and supramolecularly functionalized reduced graphene oxide are selected as hybrid components of visible-light-driven (VLD) heterojunctions to fabricate ppb-level formaldehyde (HCHO) gas sensors (named InAG sensors). Under 405 nm visible light illumination, the sensor exhibits an outstanding response toward ppb-level HCHO at room temperature, including the ultralow practical limit of detection (pLOD) of 5 ppb, high response (R_a/R_g = 2.4, 500 ppb), relatively short response/recovery time (119 s/179 s, 500 ppb), high selectivity, and long-term stability. The ultrasensitive room temperature HCHO-sensing property is derived from visible-light-driven and large-area heterojunctions between ultrasmall In₂O₃ nanorods and supramolecularly functionalized graphene nanosheets. The performance of the actual detection toward HCHO is evaluated in a 3 m³ test chamber, confirming the practicability and reliability of the InAG sensor. This work provides an effective strategy for the development of low-power-consumption ppb-level gas sensors.

Assembly of Core/Shell Nanospheres of Amorphous Hemin/Acetone-Derived Carbonized Polymer with Graphene Nanosheets for Room-Temperature NO Sensing

Implementing parts per billion-level nitric oxide (NO) sensing at room temperature (RT) is still in extreme demand for monitoring inflammatory respiratory diseases. Herein, we have prepared a kind of core-shell structural Hemin-based nanospheres (Abbr.: Hemin-nanospheres, defined as HNSs) with the core of amorphous Hemin and the shell of acetone-derived carbonized polymer, whose core-shell structure was verified by XPS with argon-ion etching. Then, the HNS-assembled reduced graphene oxide composite (defined as HNS-rGO) was prepared for RT NO sensing. The acetone-derived carbonized polymer shell not only assists the formation of amorphous Hemin core by disrupting their crystallization to release more Fe-N₄ active sites, but provides protection to the core. Owing to the unique core-shell structure, the obtained HNS-rGO based sensor exhibited superior RT gas sensing properties toward NO, including a relatively higher response (R_a/R_g = 5.8, 20 ppm), a lower practical limit of detection (100 ppb), relatively reliable repeatability (over 6 cycles), excellent selectivity, and much higher long-term stability (less than a 5% decrease over 120 days). The sensing mechanism has also been proposed based on charge transfer theory. The superior gas sensing properties of HNS-rGO are ascribed to the more Fe-N₄ active sites available under the amorphous state of the Hemin core and to the physical protection by the shell of acetone-derived carbonized polymer. This work presents a facile strategy of constructing a high-performance carbon-based core-shell nanostructure for gas sensing.

Synthesis of Graphene-Based Nanocomposites for Environmental Remediation Applications: A Review

The term graphene was coined using the prefix "graph" taken from graphite and the suffix "-ene" for the C=C bond, by Boehm et al. in 1986. The synthesis of graphene can be done using various methods. The synthesized graphene was further oxidized to graphene oxide (GO) using different methods, to enhance its multitude of applications. Graphene oxide (GO) is the oxidized analogy of graphene, familiar as the only intermediate or precursor for obtaining the latter at a large scale. Graphene oxide has recently obtained enormous popularity in the energy, environment, sensor, and biomedical fields and has been handsomely exploited for water purification membranes. GO is a unique class of mechanically robust, ultrathin, high flux, high-selectivity, and fouling-resistant separation membranes that provide opportunities to advance water desalination technologies. The facile synthesis of GO membranes opens the doors for ideal next-generation membranes as cost-effective and sustainable alternative to long existing thin-film composite membranes for water purification applications. Many types of GO-metal oxide nanocomposites have been used to eradicate the problem of metal ions, halomethanes, other organic pollutants, and different colors from water bodies, making water fit for further use. Furthermore, to enhance the applications of GO/metal oxide nanocomposites, they were deposited on polymeric membranes for water purification due to their relatively low-cost, clear pore-forming mechanism and higher flexibility compared to inorganic membranes. Along with other applications, using these nanocomposites in the preparation of membranes not only resulted in excellent fouling resistance but also could be a possible solution to overcome the trade-off between water permeability and solute selectivity. Hence, a GO/metal oxide nanocomposite could improve overall performance, including antibacterial properties, strength, roughness, pore size, and the surface hydrophilicity of the membrane. In this review, we highlight the structure and synthesis of graphene, as well as graphene oxide, and its decoration with a polymeric membrane for further applications.

Direct Synthesis of MoS2 Nanosheets in Reduced Graphene Oxide Nanoscroll for Enhanced Photodetection

Due to their unique tubular and spiral structure, graphene and graphene oxide nanoscrolls (GONS) have shown extensive applications in various fields. However, it is still a challenge to improve the optoelectronic application of graphene and GONS because of the zero bandgap of graphene. Herein, ammonium tetrathiomolybdate ((NH₄)₂MoS₄) was firstly wrapped into the ((NH₄)₂MoS₄@GONS) by molecular combing the mixture of (NH₄)₂MoS₄ and GO solution on hydrophobic substrate. After thermal annealing, the (NH₄)₂MoS₄ and GO were converted to MoS₂ nanosheets and reduced GO (RGO) simultaneously, and, thus, the MoS₂@RGONS was obtained. Raman spectroscopy and high-resolution transmission electron microscopy were used to confirm the formation of MoS₂ nanosheets among the RGONS. The amount of MoS₂ wrapped in RGONS increased with the increasing height of GONS, which is confirmed by the atomic force microscopy and Raman spectroscopy. The as-prepared MoS₂@RGONS showed much better photoresponse than the RGONS under visible light. The photocurrent-to-dark current ratios of photodetectors based on MoS₂@RGONS are ~570, 360 and 140 under blue, red and green lasers, respectively, which are 81, 144 and 35 times of the photodetectors based on RGONS. Moreover, the MoS₂@RGONS-based photodetector exhibited good power-dependent photoresponse. Our work indicates that the MoS₂@RGONS is expected to be a promising material in the fields of optoelectronic devices and flexible electronics.

Assembling Hollow Cactus-Like ZnO Nanorods with Dipole-Modified Graphene Nanosheets for Practical Room-Temperature Formaldehyde Sensing

Formaldehyde (HCHO) sensing plays a critical role for indoor environment monitoring in smart home systems. Inspired by the unique hierarchical structure of cactus, we have prepared a ZnO/ANS-rGO composite for room-temperature (RT) HCHO sensing, through assembling hollow cactus-like ZnO nanorods with 5-aminonaphthalene-1-sulfonic acid (ANS)-modified graphene nanosheets in a facile and template-free manner. Interestingly, it was found that the ZnO morphology could be simply tuned from flower clusters to hollow cactus-like nanostructures, along with the increase of the reaction time during the assembly process. The ZnO/ANS-rGO-based sensors exhibited superior RT HCHO-sensing performance with an ultrahigh response (68%, 5 ppm), good repeatability, long-term stability, and an outstanding practical limit of detection (LOD: 0.25 ppm) toward HCHO, which is the lowest practical LOD reported so far. Furthermore, for the first time, a 30 m³ simulation test cabinet was adapted to evaluate the practical gas-sensing performance in an indoor environment. As a result, an instantaneous response of 5% to 0.4 ppm HCHO was successfully achieved in the simulation test. The corresponding sensing mechanism was interpreted from two aspects including high charge transport capability of ANS-rGO and the distinct gas adsorbability derived from nanostructures, respectively. The combination of a biomimetic hierarchical structure and supramolecular assembly provides a promising strategy to design HCHO-sensing materials with high practicability.

Surfactant-like Peptide Self-Assembled into Hybrid Nanostructures for Electronic Nose Applications

An electronic nose (e-nose) utilizes a multisensor array, which relies on the vector contrast of combinatorial responses, to effectively discriminate between volatile organic compounds (VOCs). In recent years, hierarchical structures made of nonbiological materials have been used to achieve the required sensor diversity. With the advent of self-assembling peptides, the ability to tune nanostructuration, surprisingly, has not been exploited for sensor array diversification. In this work, a designer surfactant-like peptide sequence, CG₇-NH₂, is used to fabricate morphologically and physicochemically heterogeneous "biohybrid" surfaces on Au-covered chips. These multistructural sensing surfaces, containing immobilized hierarchical nanostructures surrounded by self-assembled monolayers, are used for the detection and discrimination of VOCs. Through a simple and judicious design process, involving changes in pH and water content of peptide solutions, a five-element biohybrid sensor array coupled with a gas-phase surface plasmon resonance imaging system is shown to achieve sufficient discriminatory capabilities for four VOCs. Moreover, the limit of detection of the multiarray system is bench-marked at <1 and 6 ppbv for hexanoic acid and phenol (esophago-gastric biomarkers), respectively. Finally, the humidity effects are characterized, identifying the dissociation rate constant as a robust descriptor for classification, further exemplifying their efficacy as biomaterials in the field of artificial olfaction.

Three-Dimensional MoS2/Reduced Graphene Oxide Nanosheets/Graphene Quantum Dots Hybrids for High-Performance Room-Temperature NO2 Gas Sensors

This study presents three-dimensional (3D) MoS₂/reduced graphene oxide (rGO)/graphene quantum dots (GQDs) hybrids with improved gas sensing performance for NO₂ sensors. GQDs were introduced to prevent the agglomeration of nanosheets during mixing of rGO and MoS₂. The resultant MoS₂/rGO/GQDs hybrids exhibit a well-defined 3D nanostructure, with a firm connection among components. The prepared MoS₂/rGO/GQDs-based sensor exhibits a response of 23.2% toward 50 ppm NO₂ at room temperature. Furthermore, when exposed to NO₂ gas with a concentration as low as 5 ppm, the prepared sensor retains a response of 15.2%. Compared with the MoS₂/rGO nanocomposites, the addition of GQDs improves the sensitivity to 21.1% and 23.2% when the sensor is exposed to 30 and 50 ppm NO₂ gas, respectively. Additionally, the MoS₂/rGO/GQDs-based sensor exhibits outstanding repeatability and gas selectivity. When exposed to certain typical interference gases, the MoS₂/rGO/GQDs-based sensor has over 10 times higher sensitivity toward NO₂ than the other gases. This study indicates that MoS₂/rGO/GQDs hybrids are potential candidates for the development of NO₂ sensors with excellent gas sensitivity.

CarbonIron Electron Transport Channels in Porphyrin-Graphene Complex for ppb-Level Room Temperature NO Gas Sensing

It is a great challenge to develop efficient room-temperature sensing materials and sensors for nitric oxide (NO) gas, which is a biomarker molecule used in the monitoring of inflammatory respiratory diseases. Herein, Hemin (Fe (III)-protoporphyrin IX) is introduced into the nitrogen-doped reduced graphene oxide (N-rGO) to obtain a novel sensing material HNG-ethanol. Detailed XPS spectra and DFT calculations confirm the formation of carbon-iron bonds in HNG-ethanol during synthesis process, which act as electron transport channels from graphene to Hemin. Owing to this unique chemical structure, HNG-ethanol exhibits superior gas sensing properties toward NO gas (R_a /R_g  = 3.05, 20 ppm) with a practical limit of detection (LOD) of 500 ppb and reliable repeatability (over 5 cycles). The HNG-ethanol sensor also possesses high selectivity against other exhaled gases, high humidity resistance, and stability (less than 3% decrease over 30 days). In addition, a deep understanding of the gas sensing mechanisms is proposed for the first time in this work, which is instructive to the community for fabricating sensing materials based on graphene-iron derivatives in the future.

Strategies for the performance enhancement of graphene-based gas sensors: A review

Gas sensors have aroused much attention in recent years for the important effect in modern society. Graphene, with unique structure and characteristic properties, has been considered as a promising candidate for fabricating high-performance gas sensor. Great efforts in current research are directed towards exploiting various graphene-based gas sensors, but the core of gas sensing study is how to enhance the gas sensing performance. Herein, we propose a perspective that focuses on the strategies for sensing performance enhancement of graphene-based gas sensors. Several strategies are reviewed such as the modification of graphene with organic molecules, functionalization by metal oxide or noble metals, and nanostructural engineering. Particular emphasis is also provided to clarify the mechanism for the gas sensing enhancement. Further, the sensor device design is also concerned for the significant effect on reaching full potential of the gas sensing materials and realizing multifunctional integration. Finally, the opportunities and challenges for the development of gas sensors are pointed out.

Effects of external electric field on the sensing property of volatile organic compounds over Janus MoSSe monolayer: a first-principles investigation

Janus 2D transition metal dichalcogenide (TMD) is a new generation 2D material with a unique asymmetric structure. This asymmetric structure (or out-off plane symmetric geometry) of Janus 2D TMD has been reported to yield tunable electronic properties through strain and electric field, which can also be applied in gas sensing. In this work, we performed DFT calculations to investigate the gas sensing property of cyclohexane and acetone on MoS2 and Janus MoSSe monolayers under external electric fields. Our results show that cyclohexane possesses slightly larger adsorption energy on pristine MoS2 and Janus MoSSe monolayers than acetone without external electric fields. After applying the external electric fields, the adsorption energy for cyclohexane on MoS2 shows no enhancement. However, the adsorption energy of acetone shows the most substantial enhancement on the Janus MoSSe monolayer. We found that the dipole moment orientations of adsorbates and the monolayer can strongly interact with the external electric fields. Hence, the combination of polar adsorbate and polar material, i.e., acetone and Janus MoSSe, demonstrates the most vital sensitivity under the applied bias. On the other hand, the non-polar adsorbate and non-polar material combination show a negligible effect on external bias. These findings can be applied to the design of gas sensors in the future through polar materials.

A Lamellar MXene (Ti3 C2 Tx )/PSS Composite Membrane for Fast and Selective Lithium-Ion Separation

A two-dimensional (2D) laminar membrane with Li⁺ selective transport channels is obtained by stacking MXene nanosheets with the introduction of poly(sodium 4-styrene sulfonate) (PSS) with active sulfonate sites, which exhibits excellent Li⁺ selectivity from ionic mixture solutions of Na⁺ , K⁺ , and Mg²⁺ . The Li⁺ permeation rate through the MXene@PSS composite membrane is as high as 0.08 mol m^-2  h^-1 , while the Li⁺ /Mg²⁺ , Li⁺ /Na⁺ , and Li⁺ /K⁺ selectivities are 28, 15.5, and 12.7, respectively. Combining the simulation and experimental results, we further confirm that the highly selective rapid transport of partially dehydrated Li⁺ within subnanochannels can be attributed to the precisely controlled interlayer spacing and the relatively weaker ion-terminal (-SO₃ ^- ) interaction. This study deepens the understanding of ion-selective permeation in confined channels and provides a general membrane design concept.

Large-area synthesis of nanoscopic catalyst-decorated conductive MOF film using microfluidic-based solution shearing

Conductive metal-organic framework (C-MOF) thin-films have a wide variety of potential applications in the field of electronics, sensors, and energy devices. The immobilization of various functional species within the pores of C-MOFs can further improve the performance and extend the potential applications of C-MOFs thin films. However, developing facile and scalable synthesis of high quality ultra-thin C-MOFs while simultaneously immobilizing functional species within the MOF pores remains challenging. Here, we develop microfluidic channel-embedded solution-shearing (MiCS) for ultra-fast (≤5 mm/s) and large-area synthesis of high quality nanocatalyst-embedded C-MOF thin films with thickness controllability down to tens of nanometers. The MiCS method synthesizes nanoscopic catalyst-embedded C-MOF particles within the microfluidic channels, and simultaneously grows catalyst-embedded C-MOF thin-film uniformly over a large area using solution shearing. The thin film displays high nitrogen dioxide (NO₂) sensing properties at room temperature in air amongst two-dimensional materials, owing to the high surface area and porosity of the ultra-thin C-MOFs, and the catalytic activity of the nanoscopic catalysts embedded in the C-MOFs. Therefore, our method, i.e. MiCS, can provide an efficient way to fabricate highly active and conductive porous materials for various applications.

The immobilization of catalysts within the pores of conductive metal-organic frameworks (C-MOFs) via facile and scalable methodologies remains challenging. Here the authors report a microfluidic channel-embedded solution shearing process that enables the high throughput, large-area, single-step preparation of Pt nanocatalyst-embedded C-MOF thin films.

Recent advances in energy-saving chemiresistive gas sensors: A review

With the tremendous advances in technology, gas-sensing devices are being popularly used in many distinct areas, including indoor environments, industries, aviation, and detectors for various toxic domestic gases and vapors. Even though the most popular type of gas sensor, namely, resistive-based gas sensors, have many advantages over other types of gas sensors, their high working temperatures lead to high energy consumption, thereby limiting their practical applications, especially in mobile and portable devices. As possible ways to deal with the high-power consumption of resistance-based sensors, different strategies such as self-heating, MEMS technology, and room-temperature operation using especial morphologies, have been introduced in recent years. In this review, we discuss different types of energy-saving chemisresitive gas sensors including self-heated gas sensors, MEMS based gas sensors, room temperature operated flexible/wearable sensor and their application in the fields of environmental monitoring. At the end, the review will be concluded by providing a summary, challenges, recent trends, and future perspectives.

Computational Study of Janus Transition Metal Dichalcogenide Monolayers for Acetone Gas Sensing

Recently, Janus two-dimensional (2D) transition metal dichalcogenides (TMDs) have been widely investigated and have provided exciting prospects in many fields such as photoelectric materials, photocatalysis, and gas sensors. In this study, we performed density functional theory (DFT) calculations to study the sensitivity of four volatile organic compounds (VOCs), including acetone, methanol, ethanol, and formyl aldehyde, over pristine 2D TMDs and 2D Janus TMD monolayers. We found that MoS2, Janus MoSSe, and Janus MoSTe demonstrated greater sensitivity toward acetone than other VOCs. Furthermore, the band gap values of the Janus MoSSe and Janus MoSTe monolayers dramatically changed after acetone adsorption on their sulfur layers, which was quite larger than the band gap change after acetone adsorption on the MoS2 monolayer. This result also leads to the extremely large conductivity change of Janus MoSSe and Janus MoSTe after sensing acetone. Hence, Janus MoSSe and Janus MoSTe monolayers show much higher sensitivity toward acetone in comparison with the pristine MoS2 monolayer. Finally, our finding indicates that Janus MoSSe and Janus MoSTe monolayers can be proposed as ultrahigh-sensitivity 2D TMD materials for acetone sensors.

Multivariate Evaluation Method for Screening Optimum Gas-Sensitive Materials for Detecting SF6 Decomposition Products

In previous studies, the selection of optimal gas-sensing materials for detecting target gases mainly relied on their response value, but other indices, such as the recovery capability of materials, have usually been overlooked. Here, we propose a new method for evaluating sensor effectiveness that includes a broader range of performance indices. In this study, four gas sensors based on metal-oxide semiconductors (WO₃, CeO₂, In₂O₃, and SnO₂) were used as examples, and their performance in the detection of four decomposition products of sulfur hexafluoride (SF₆) was investigated. After gas-sensing experiments, values for working temperature, response value, and recovery capability were obtained. A multivariate evaluation method of mixing principal component analysis, information entropy, and variation coefficient was developed to calculate the weights of various indices, and the sensors' optimal working temperatures could be identified quantitatively. Using five variables (working temperature, response value, recovery capability, fluctuation rate, and detection limit), we continued to apply this multivariate evaluation method to calculate the weights and acquire comprehensive scores for the four sensors. Finally, these scores were used to identify the optimal materials for detecting SF₆ decomposition products. This procedure has the potential for selecting the best sensors for other gases.

Laser Writing of Janus Graphene/Kevlar Textile for Intelligent Protective Clothing

Protective clothing plays a vital role in safety and security. Traditional protective clothing can protect the human body from physical injury. It is highly desirable to integrate modern wearable electronics into a traditional protection suit to endow it with versatile smart functions. However, it is still challenging to integrate electronics into clothing through a practical approach while keeping the intrinsic flexibility and breathability of textiles. In this work, we realized the direct writing of laser-induced graphene (LIG) on a Kevlar textile in air and demonstrated the applications of the as-prepared Janus graphene/Kevlar textile in intelligent protective clothing. The C═O and N-C bonds in Kevlar were broken, and the remaining carbon atoms were reorganized into graphene, which can be ascribed to a photothermal effect induced by the laser irradiation. Proof-of-concept devices based on the prepared graphene/Kevlar textile, including flexible Zn-air batteries, electrocardiogram electrodes, and NO₂ sensors, were demonstrated. Further, we fabricated self-powered and intelligent protective clothing based on the graphene/Kevlar textile. The laser-induced direct writing of graphene from commercial textiles in air conditions provides a versatile and rapid route for the fabrication of textile electronics.

Triazine-Based Two-Dimensional Organic Polymer for Selective NO2 Sensing with Excellent Performance

Gas sensors with high sensitivity, fast response/recovery, good selectivity, and room-temperature operation are highly desirable for practical use. However, most of the existing gas sensing materials, either conventional metal oxide semiconductors or advanced inorganic two-dimensional (2D) polymers, can hardly satisfy the above requirements. Herein, we demonstrate an organic 2D polymer derived from a covalent triazine framework (CTF), which possesses nanoscale thickness, intrinsic and periodic pore structures, and abundant functional groups with excellent gas sensing performance. The as-prepared triazine-based 2D polymer (T-2DP) exhibits selective recognition to NO₂ with an ultrahigh sensitivity of 452.6 ppm^-1, which outperforms most other 2D nanomaterials and its CTF matrix. The sensing effect is superfast (35-47 s) and fully reversible operated at room temperature. The superior comprehensive gas sensing performance of T-2DP and the underlying mechanism was experimentally studied and further discussed by comparison with that of CTF and widely investigated inorganic 2D polymers including graphene and MXene. As a proof of concept, a flexible NO₂ chemiresistor based on T-2DP was fabricated to demonstrate its potential for integration into wearable electronics. The scientific findings in this work may propose a new route for the design of high-performance gas sensing materials on the basis of organic 2D polymers in next-generation wearable electronic devices.

Catalytic Metal Nanoparticles Embedded in Conductive Metal-Organic Frameworks for Chemiresistors: Highly Active and Conductive Porous Materials

Conductive porous materials having a high surface reactivity offer great promise for a broad range of applications. However, a general and scalable synthesis of such materials remains challenging. In this work, the facile synthesis of catalytic metal nanoparticles (NPs) embedded in 2D metal-organic frameworks (MOFs) is reported as highly active and conductive porous materials. After the assembly of 2D conductive MOFs (C-MOFs), i.e., Cu3(hexahydroxytriphenylene)2 [Cu3(HHTP)2], Pd or Pt NPs are functionalized within the cavities of C-MOFs by infiltration of metal ions and subsequent reduction. The unique structure of Cu3(HHTP)2 with a cavity size of 2 nm confines the bulk growth of metal NPs, resulting in ultra-small (≈2 nm) and well-dispersed metal NPs loaded in 2D C-MOFs. The Pd or Pt NPs-loaded Cu3(HHTP)2 exhibits remarkably improved NO2 sensing performance at room temperature due to the high reactivity of catalytic metal NPs and the high porosity of C-MOFs. The catalytic effect of Pd and Pt NPs on NO2 sensing of Cu3(HHTP)2, in terms of reaction rate kinetics and activation energy, is demonstrated.

High Selectivity Gas Sensing and Charge Transfer of SnSe2

SnSe₂ is an anisotropic binary-layered material with rich physics, which could see it used for a variety of potential applications. Here, we investigate the gas-sensing properties of SnSe₂ using first-principles calculations and verify predictions using a gas sensor made of few-layer SnSe₂ grown by chemical vapor deposition. Theoretical simulations indicate that electrons transfer from SnSe₂ to NO₂, whereas the direction of charge transfer is the opposite for NH₃. Notably, a flat molecular band appears around the Fermi energy after NO₂ adsorption and the induced molecular band is close to the conduction band minimum. Moreover, compared with NH₃, NO₂ molecules adsorbed on SnSe₂ have a lower adsorption energy and a higher charge transfer value. The dynamic-sensing responses of SnSe₂ sensors confirm the theoretical predictions. The good match between the theoretical prediction and experimental demonstration suggests that the underlying sensing mechanism is related to the charge transfer and induced flat band. Our results provide a guideline for designing high-performance gas sensors based on SnSe₂.

Two-Dimensional NbS2 Gas Sensors for Selective and Reversible NO2 Detection at Room Temperature

Transition metal dichalcogenides (TMDs) have attracted enormous attention in diverse research fields. Especially, gas sensors are considered in a promising application exploiting TMDs. However, the studies are confined to only major TMDs such as MoS₂ and WS₂. Particularly, the chemoresistive sensing properties of two-dimensional (2D) NbS₂ have never been explored. For the first time, we report room temperature NO₂ sensing characteristics of 2D NbS₂ nanosheets and the sensing mechanisms using first-principles calculations based on density functional theory. The results demonstrate that the NbS₂ edges possessing different configurations depending on synthetic conditions differ in the sensing ability of the TMD nanosheets. This study not only broadens the potential of 2D NbS₂ for gas sensing applications, but also presents the important role of edge configuration of TMDs depending on synthetic conditions for further studies.

Construction of ZnO/SnO2 Heterostructure on Reduced Graphene Oxide for Enhanced Nitrogen Dioxide Sensitive Performances at Room Temperature

The employment of n-n homotypic heterogeneous junctions is an efficient method to improve sensitive performance of metal oxide-based gas sensors owing to the generation of charge accumulation regions. Herein, in order to further enhance nitrogen dioxide (NO₂) sensing properties of the sensors based on reduced graphene oxide (RGO) at room temperature (RT), n-type ZnO nanoparticles (NPs) decorated n-type SnO₂ NPs heterojunctions were successfully constructed on RGO nanosheets (NSs) by combination of the hydrothermal method and the wet-chemical deposition method. The formation of heterostructures between ZnO NPs and SnO₂ NPs was confirmed by the nonlinear behavior of current versus voltage (I-V) curve of ZnO/SnO₂-RGO. ZnO/SnO₂-RGO based sensor displayed remarkably enhanced response (141.0%) for detecting 5 ppm of NO₂ at RT, which is almost 4 and 3 times higher than that of SnO₂-RGO (34.8%) and ZnO-RGO (43.3%), respectively. Moreover, as far as the ZnO/SnO₂-RGO-based sensor is concerned, its response and recovery time (33 and 92 s) are also significantly decreased, compared to SnO₂-RGO-based sensor (70 and 39 s) and ZnO-RGO-based sensor (272 and 1297 s). In this work, the improved NO₂ sensing properties of the sensors based on RGO not only benefit from the effects of the heterostructures between SnO₂ and ZnO, but also derive from the superior electrical characteristics of RGO. In particular, the n-n heterojunctions could offer facile access to effective electronic interaction and improve transfer efficiency of the charges at the interface to adsorbed oxygen. Meanwhile, the n-n heterojunctions can also provide additional reaction center for adsorbing gas.

Biomimetic Turbinate-like Artificial Nose for Hydrogen Detection Based on 3D Porous Laser-Induced Graphene

Inspired by the turbinate structure in the olfaction system of a dog, a biomimetic artificial nose based on 3D porous laser-induced graphene (LIG) decorated with palladium (Pd) nanoparticles (NPs) has been developed for room-temperature hydrogen (H₂) detection. A 3D porous biomimetic turbinate-like network of graphene was synthesized by simply irradiating an infrared laser beam onto a polyimide substrate, which could further be transferred onto another flexible substrate such as polyethylene terephthalate (PET) to broaden its application. The sensing mechanism is based on the catalytic effect of the Pd NPs on the crystal defect of the biomimetic LIG turbinate-like microstructure, which allows facile adsorption and desorption of the nonpolar H₂ molecules. The sensor demonstrated an approximately linear sensing response to H₂ concentration. Compared to chemical vapor-deposited (CVD) graphene-based gas sensors, the biomimetic turbinate-like microstructure LIG-gas sensor showed ∼1 time higher sensing performance with much simpler and lower-cost fabrication. Furthermore, to expand the potential applications of the biomimetic sensor, we modulated the resistance of the biomimetic LIG sensor by varying laser sweeping gaps and also demonstrated a well-transferred LIG layer onto transparent substrates. Moreover, the LIG sensor showed good mechanical flexibility and robustness for potential wearable and flexible device applications.

Oxygen-Defective Ultrathin BiVO4 Nanosheets for Enhanced Gas Sensing

BiVO₄ nanomaterials are potentially applicable in gas sensing, but the sensing performance is limited by the less active sites on the BiVO₄ surface. In this work, we propose a strategy to improve the gas-sensing performance of BiVO₄ by forming ultrathin nanosheets and introducing oxygen vacancies, which increase the surface active sites. Two-dimensional (2D) BiVO₄ nanosheets with oxygen vacancies are prepared through a colloidal method with the assistance of nitric acid. Gas sensors based on the oxygen-defective 2D ultrathin BiVO₄ nanosheets exhibit an enhanced sensing response, which is 3.4 times higher than those of the sensors based on oxygen-abundant BiVO₄ nanosheets. The density functional theory calculation is employed to uncover the promoting effects of oxygen vacancies on enhancing the O₂ adsorption capability of BiVO₄ nanosheets. This work is not only expected to build a wide range of 2D metal oxide semiconductors with a high gas-sensing performance but also gives an insight into the mechanism of the enhanced response induced by the oxygen vacancies, which will be a guideline for further designing high-performance sensing materials.

Functional Supramolecular Gels Based on the Hierarchical Assembly of Porphyrins and Phthalocyanines

Supramolecular gels containing porphyrins and phthalocyanines motifs are attracting increased interests in a wide range of research areas. Based on the supramolecular gels systems, porphyrin or phthalocyanines can form assemblies with plentiful nanostructures, dynamic, and stimuli-responsive properties. And these π-conjugated molecular building blocks also afford supramolecular gels with many new features, depending on their photochemical and electrochemical characteristics. As one of the most characteristic models, the supramolecular chirality of these soft matters was investigated. Notably, the application of supramolecular gels containing porphyrins and phthalocyanines has been developed in the field of catalysis, molecular sensing, biological imaging, drug delivery and photodynamic therapy. And some photoelectric devices were also fabricated depending on the gelation of porphyrins or phthalocyanines. This paper presents an overview of the progress achieved in this issue along with some perspectives for further advances.

Highly Sensitive, Selective, and Flexible NO2 Chemiresistors Based on Multilevel Structured Three-Dimensional Reduced Graphene Oxide Fiber Scaffold Modified with Aminoanthroquinone Moieties and Ag Nanoparticles

Highly sensitive, selective, and room-temperature-performing gas sensors have always been the pursuit in the sensing field for practical applications. However, the existing gas sensors can seldom satisfy the aforementioned requirements. Here, we integrate zero-dimensional Ag nanoparticles (AgNPs), one-dimensional polymer fibers, and two-dimensional aminoanthroquinone-functionalized reduced graphene oxide (AQRGO) sheets into a three-dimensional sensing scaffold (AgNP-3D-AQRGO) for high-performance NO₂ sensing. The AQ moieties and AgNPs are decorated onto the RGO sheets through a wet chemical route. Electrospinning and self-assembly techniques are employed to assemble the polymer fibers and the functional RGO sheets into a three-dimensional scaffold. The resulting AgNP-3D-AQRGO-based gas sensor can perform at room temperature and exhibits excellent sensing performance for NO₂, including an ultrahigh sensitivity (10.3 ppm^-1), an ultralow limit of detection (0.6 ppb), and an extremely remarkable selectivity to solely NO₂ molecules. Furthermore, the sensor is also highly flexible, demonstrating great potential for portable and real-time monitoring of toxic gas in personal mobile electronics.

Cardiomyocyte-Driven Structural Color Actuation in Anisotropic Inverse Opals

Biohybrid actuators composed of living tissues and artificial materials have attracted increasing interest in recent years because of their extraordinary function of dynamically sensing and interacting with complex bioelectrical signals. Here, a compound biohybrid actuator with self-driven actuation and self-reported feedback is designed based on an anisotropic inverse opal substrate with periodical elliptical macropores and a hydrogel filling. The benefit of the anisotropic surface topography and high biocompatibility of the hydrogel is that the planted cardiomyocytes could be induced into a highly ordered alignment with recovering autonomic beating ability on the elastic substrate. Because of the cell elongation and contraction during cardiomyocyte beating, the anisotropic inverse opal substrates undergo a synchronous cycle of deformation actuations, which can be reported as corresponding shifts of their photonic band gaps and structural colors. These self-driven biohybrid actuators could be used as elements for the construction of a soft-bodied structural color robot, such as a biomimetic guppy with a swinging tail. Besides, with the integration of a self-driven biohybrid actuator and microfluidics, the advanced heart-on-a-chip system with the feature of microphysiological visuality has been developed for integrated cell monitoring and drug testing. This anisotropic inverse opal-derived biohybrid actuator could be widely applied in biomedical engineering.

Assembly with copper(ii) ions and D–π–A molecules on a graphene surface for ultra-fast acetic acid sensing at room temperature

The as-prepared 4HQ-rGO/Cu²⁺ sensor possessed a high response, outstanding selectivity and fast response-recovery characteristic, which was mainly attributed to the supramolecularly assemble of 4-hydroxyquinoline, and Cu²⁺ with graphene nanosheets.

Highly Promoted Carrier Mobility and Intrinsic Stability by Rolling Up Monolayer Black Phosphorus into Nanoscrolls

Rolling up two-dimensional (2D) materials into nanoscrolls could not only retain the excellent properties of their 2D hosts but also display intriguing physical and chemical properties that arise from their 1D tubular structures. Here, we report a new class of black phosphorus nanoscrolls (bPNSs), which are stable at room-temperature and energetically more favorable than 2D bP. Most strikingly, these bPNSs hold tunable direct band gaps and extremely high mobilities (e.g., the mobility of the double-layer bPNS is about 20-fold higher than that of 2D bP monolayer). Their unique self-encapsulation structure and layer-dependent conduction band minimum can largely prevent the entrance of O₂ and the production of O₂^- and thereby suppress the possible environmental degradation as well. The enhanced intrinsic stability and promoted electronic properties render bPNSs great promise in many advanced electronics or optoelectronics applications.

Self-Powered Multifunctional Transient Bioelectronics

Controllable degradation and excellent biocompatibility during/after a lifetime endow emerging transient electronics with special superiority in implantable biomedical applications. Currently, most of these devices need external power sources, limiting their real-world utilizations. Optimizing existing bioresorbable electronic devices requires natural-material-based construction and, more importantly, diverse or even all-in-one multifunctionalization. Herein, silk-based implantable, biodegradable, and multifunctional systems, self-powered with transient triboelectric nanogenerators (T² ENGs), for real-time in vivo monitoring and therapeutic treatments of epileptic seizures, are reported. These T² ENGs are of customizable in vitro/in vivo operating life and biomechanical sensitivity via the adjustments of silk molecular size, surface structuralization, and device configuration. Functions, such as drug delivery and structural-integrity optical readout (parallel to electronic signals), are enabled for localized anti-infection and noninvasive degradation indication, respectively. A proof-of-principle wireless system is built with mobile-device readout and "smart" treatment triggered by specific symptoms (i.e., epilepsy), exhibiting the practical potential of these silk T² ENGs as self-powered, transient, and multifunctional implantable bioelectronic platforms.