Electroactive Biofilms for Sensing: Reflections and Perspectives

Highly sensitive standardized toxicity biosensors for rapid water quality warning

Microbial electrochemical sensor (MES) using electroactive biofilm (EAB) as the sensing element represents a broad-spectrum technology for early warning of biotoxicity of water samples. However, its commercial application is impeded by limited sensitivity and repeatability. Here, we proposed a layered standardized EAB (SEAB) with enriched Geobacter anodireducens SD-1 in the inner layer and self-matched outer layer. The SEAB sensors showed a 2.3 times higher sensitivity than conventional EAB acclimated directly from wastewater (WEAB). A highly repeatable response sensitivity was concentrated at 0.011 ± 0.0006 A/m2/ppm in 4 replicated batches of SEAB sensors (R2 > 0.95), highlighting their potential for reliable toxicity monitoring in practical applications. In contrast, the sensing performance of all WEAB sensors was unpredictable. SEAB also exhibited a better tolerance towards low concentration of formaldehyde, with only a 4 % loss in viability. Our findings improved the sensitivity and reproducibility of standardized MES for toxicity early warning.

Assessment of the microbial electrochemical sensor (SENTRY™) as a potential wastewater quality monitoring tool for common pollutants found in Malaysia

Bioelectrochemical sensors for environment monitoring have the potential to provide facility operators with real-time data, allowing for better and more timely decision-making regarding water and wastewater treatment. To assess the robustness and sensitivity of the Sentry™ biosensor in local conditions, it was tested in Malaysia using domestically available wastewater. The study objectives included (1) enrich the biosensor locally, (2) operate and test the biosensor with local domestic wastewater, and (3) determine the biosensor's responsiveness to model pollutants through pollutant spike and immersion test as well as response to absence of wastewater. Lab-scale operation shows the biosensor was successfully enriched with (1) local University Kebangsaan Malaysia's, microbial community strain collection and (2) local municipal wastewater microflora, operated for more than 50 days with a stable yet responsive carbon consumption rate (CCR) signal. Meanwhile, two independent biosensors were also enriched and operated in Indah Water Research Centre's crude sewage holding tank, showing a stable response to the wastewater. Next, a pilot scale setup was constructed to test the enriched biosensors for the spiked-pollutant test. The biosensors showed a proportional CCR response (pollutant presence detected) towards several organic compounds in the sewage, including ethanol, chicken blood, and dilution of tested sewage but less to curry powder, methanol, and isopropanol. Conversely, there was no significant response (pollutant presence not detected) towards hexane, Congo red, engine oil, and paint, which may be due to their non-biodegradability and/or insoluble nature. Additionally, the biosensors were exposed to air for 6 h to assess their robustness towards aerobic shock with a positive result. Overall, the study suggested that the biosensor could be a powerful monitoring tool, given its responsiveness towards organic compounds in sewage under normal conditions.

Examining the resistance and resilience of anode-respiring Shewanella oneidensis biohybrid using microsensors

Immobilizing electro-active microbes within polymer matrices (thereby forming biohybrids) is a promising approach to accelerate microbial attachment to electrodes and increase the biofilm robustness. However, little is known on the fine scale chemical environment that develops within the electro-active biohybrids. Herein, we develop a biohybrid by immobilizing a culture of Shewanella oneidensis MR1 in agar matrix on the surface of a graphite electrode poised at +0.25 V. The resulting bioanode (3-6 mm thick) was grown under anoxic conditions and produced a steady current of 40 μA. Oxygen and pH distribution within the biohybrid were characterized in-situ using microsensors. As Shewanella is a facultative aerobe, it will halt the current production in the presence of oxygen. Thus, in addition, we investigated the alteration of the microenvironment during and after aeration of the medium to evaluate the oxygen tolerance of the system. During aeration, oxygen was effectively consumed in the top layers of the biofilm, leaving a 400-900 μm thick anoxic zone on the anode surface, that sustained >60% of the initial current. Current production recovered to pre-oxic condition within 5 h after the aeration was stopped, showing that immobilization can promote both high resistance and resilience of the system. Despite the absence of strong buffering conditions, pH profiles indicated a maximum drop of 0.2 units across the biohybrid. Characterizing the chemical microenvironment helps to elucidate the mechanistic functioning of artificial biofilms and hold a great potential for the designing of future, more effective biohybrid electrodes.

Periodic polarization duty cycle tunes performance and adhesion of anodic electroactive biofilms

Periodic polarization can improve the performance of anodic electroactive biofilms (EABs). The impact of the half-period duration was previously investigated at constant duty cycle (50%), i.e., the proportion of a period during which the electrode is polarized. Here, we cultured eight EABs on glassy carbon electrodes at four different duty cycles (50%, 67%, 80% and 91%) by varying the time interval under open circuit conditions, while keeping the polarization duration at 10 s. The shorter duty cycles slightly slowed initial growth but produced EABs generating higher faradaic currents. The total charge recovery over 38 days increased with decreasing duty cycles from 0.53 kC.cm-2 (duty cycle of 91%) to 1.65 kC.cm-2 (50%). EABs with the shortest duty cycle fully detached twice from the electrode surface, but detachments were quickly followed by the formation of more efficient EABs. We then carried out controlled removal of some aged and low current-producing EABs by applying a 30 s cathodic current (H2 evolution at -15 mA.cm-2) and observed the subsequent rapid development of fresh EABs displaying better electrochemical performance. Our results illustrate that well-chosen dynamic controls of electrode potentials can substantially improve the average current production of EABs, or allow a simple replacement of underperforming EABs.

Instant water toxicity detection based on magnetically-constructed electrochemically active biofilm

Water toxicity determination with electrochemically active bacteria (EAB) is promising in the early warning of water pollution. However, limited by tedious biofilm formation, natural EAB biofilms are uncapable of the instant detection of water toxicity, resulting in the failure for the emergency monitoring of water pollution. To solve this problem, a novel method for the rapid construction of EAB biofilms using magnetic adsorption was established, and the performance of instant water toxicity detection with magnetically-constructed EAB biofilm was investigated. The results demonstrate that EAB biofilms were magnetically constructed in less than 30 min, and magnetically-constructed EAB biofilm generated stable currents even under continuous flow conditions. Magnetically-constructed EAB biofilms realized instant water toxicity detection, and the sensitivity increased with the decrease of magnetic field intensity. Low magnetic field intensity resulted in a loose biofilm structure, which is conducive to toxic pollutant penetration. The detection limit for Cu2+, phenol, and Cd2+ achieved 0.07 mg/L with optimal magnetic field intensity, and the detection time was less than 30 min. This study broadens the application of water toxicity determination with EAB, and establishes a foundation for the instant and continuous detection of water toxicity with EAB.

Exploring the biocapacitance in M3C-based biosensors for the assessment of microbial activity and organic matter

Reliable monitoring of microbial and water quality parameters in freshwater ecosystems (either natural or human-made) is of capital importance for improving both the management of water resources and the assessment of microbially-driven bio-geo-chemical processes. In this context, bioelectrochemical systems (BES), such as microbial three-cell electrodes (M3C), are very promising devices for their use as biosensors. However, current experiences on the use of BES-based devices for biosensing purposes are almost exclusively limited to water-saturated environments. This limitation hampers the use of this technology for a wider range of applications where the biosensor may work discontinuously (such as discontinuously saturated ecosystems). Discontinuous operation of M3C-based biosensors creates an electric current peak immediately after the reconnection of the system due to electron accumulation, in a process known as biocapacitance. The present work aimed at quantifying the bioindication potential of biocapacitance for the assessment of key ecosystem parameters such as microbial metabolic activity and biomass, as well as organic matter concentration. Significant linear regression coefficients (R2 > 0.9) were found for all combinations of parameters tested. Moreover, for most of the ecological parameters assessed, an electric charge accumulation of 1-5 min (biocapacitance elapsed time) and discharge of 5 min was enough to get reliable information. In conclusion, we have demonstrated for the first time that biocapacitance in M3C-based biosensors can be used as a proxy parameter for the assessment of microbial activity, microbial biomass and organic matter concentration in a model nature-based ecosystem.

A review of biosensor for environmental monitoring: principle, application, and corresponding achievement of sustainable development goals

Human health/socioeconomic development is closely correlated to environmental pollution, highlighting the need to monitor contaminants in the real environment with reliable devices such as biosensors. Recently, variety of biosensors gained high attention and employed as in-situ application, in real-time, and cost-effective analytical tools for healthy environment. For continuous environmental monitoring, it is necessary for portable, cost-effective, quick, and flexible biosensing devices. These benefits of the biosensor strategy are related to the Sustainable Development Goals (SDGs) established by the United Nations (UN), especially with reference to clean water and sources of energy. However, the relationship between SDGs and biosensor application for environmental monitoring is not well understood. In addition, some limitations and challenges might hinder the biosensor application on environmental monitoring. Herein, we reviewed the different types of biosensors, principle and applications, and their correlation with SDG 6, 12, 13, 14, and 15 as a reference for related authorities and administrators to consider. In this review, biosensors for different pollutants such as heavy metals and organics were documented. The present study highlights the application of biosensor for achieving SDGs. Current advantages and future research aspects are summarized in this paper.Abbreviations: ATP: Adenosine triphosphate; BOD: Biological oxygen demand; COD: Chemical oxygen demand; Cu-TCPP: Cu-porphyrin; DNA: Deoxyribonucleic acid; EDCs: Endocrine disrupting chemicals; EPA: U.S. Environmental Protection Agency; Fc-HPNs: Ferrocene (Fc)-based hollow polymeric nanospheres; Fe₃O₄@3D-GO: Fe₃O₄@three-dimensional graphene oxide; GC: Gas chromatography; GCE: Glassy carbon electrode; GFP: Green fluorescent protein; GHGs: Greenhouse gases; HPLC: High performance liquid chromatography; ICP-MS: Inductively coupled plasma mass spectrometry; ITO: Indium tin oxide; LAS: Linear alkylbenzene sulfonate; LIG: Laser-induced graphene; LOD: Limit of detection; ME: Magnetoelastic; MFC: Microbial fuel cell; MIP: Molecular imprinting polymers; MWCNT: Multi-walled carbon nanotube; MXC: Microbial electrochemical cell-based; NA: Nucleic acid; OBP: Odorant binding protein; OPs: Organophosphorus; PAHs: Polycyclic aromatic hydrocarbons; PBBs: Polybrominated biphenyls; PBDEs: Polybrominated diphenyl ethers; PCBs: Polychlorinated biphenyls; PGE: Polycrystalline gold electrode; photoMFC: photosynthetic MFC; POPs: Persistent organic pollutants; rGO: Reduced graphene oxide; RNA: Ribonucleic acid; SDGs: Sustainable Development Goals; SERS: Surface enhancement Raman spectrum; SPGE: Screen-printed gold electrode; SPR: Surface plasmon resonance; SWCNTs: single-walled carbon nanotubes; TCPP: Tetrakis (4-carboxyphenyl) porphyrin; TIRF: Total internal reflection fluorescence; TIRF: Total internal reflection fluorescence; TOL: Toluene-catabolic; TPHs: Total petroleum hydrocarbons; UN: United Nations; VOCs: Volatile organic compounds.

Influence of Hydrodynamic Forces on Electroactive Bacterial Adhesion in Microbial Fuel Cell Anodes

This investigation examined the role of shear stress on the dynamic development of microbial communities within anodic biofilms in single-chamber microbial fuel cells (MFCs). Bacterial attachment to surfaces, often regarded as a crucial step in biofilm formation, may significantly contribute to the selection of electroactive bacteria (EAB). It is well established that hydrodynamic forces, particularly shear forces, have a profound influence on bacterial adhesion. This study postulates that shear stress could select EAB on the anode during the adhesion phase by detaching non-EAB. To examine this hypothesis, MFC reactors equipped with a shear stress chamber were constructed, creating specific shear stress on the anode. The progression of adhesion under various shear stress conditions (1, 10, and 50 mPa) was compared with a control MFC lacking shear stress. The structure of the microbial community was assessed using 16S rRNA gene (rrs) sequencing, and the percentage of biofilm coverage was analyzed using fluorescence microscopy. The results indicate a significant impact of shear stress on the relative abundance of specific EAB, such as Geobacter, which was higher (up to 30%) under high shear stress than under low shear stress (1%). Furthermore, it was noted that shear stress decreased the percentage of biofilm coverage on the anodic surface, suggesting that the increase in the relative abundance of specific EAB occurs through the detachment of other bacteria. These results offer insights into bacterial competition during biofilm formation and propose that shear stress could be utilized to select specific EAB to enhance the electroactivity of anodic biofilms. However, additional investigations are warranted to further explore the effects of shear stress on mature biofilms.

Water treatment and reclamation by implementing electrochemical systems with constructed wetlands

Seasonal or permanent water scarcity in off-grid communities can be alleviated by recycling water in decentralized wastewater treatment systems. Nature-based solutions, such as constructed wetlands (CWs), have become popular solutions for sanitation in remote locations. Although typical CWs can efficiently remove solids and organics to meet water reuse standards, polishing remains necessary for other parameters, such as pathogens, nutrients, and recalcitrant pollutants. Different CW designs and CWs coupled with electrochemical technologies have been proposed to improve treatment efficiency. Electrochemical systems (ECs) have been either implemented within the CW bed (ECin-CW) or as a stage in a sequential treatment (CW + EC). A large body of literature has focused on ECin-CW, and multiple scaled-up systems have recently been successfully implemented, primarily to remove recalcitrant organics. Conversely, only a few reports have explored the opportunity to polish CW effluents in a downstream electrochemical module for the electro-oxidation of micropollutants or electro-disinfection of pathogens to meet more stringent water reuse standards. This paper aims to critically review the opportunities, challenges, and future research directions of the different couplings of CW with EC as a decentralized technology for water treatment and recovery.

Innovative electrochemical biosensor with nitrifying biofilm and nitrite oxidation signal for comprehensive toxicity detection in Tuojiang River

Water toxicity detection, as a valuable supplement to conventional water quality measurement, is an important method for evaluating water environmental quality standards. However, the toxicity of composite pollutants is more complicated due to their mixture effects. This study developed a novel, rapid and interference-resistant detection method for water toxicity based on an electrochemical biosensor using peak current from nitrite oxidation as a signal. Toxicants could weaken the characteristic peak current of nitrite to indicate the magnitude of toxicity. The proof-of-concept study was first conducted using a synthetic water sample containing trichloroacetic acid (TCAA), and then the results were compared with those of the traditional toxicity colorimetric method (CCK-8 kit) and laser confocal microscopy (CLSM). The accuracy of the biosensor was further verified with water samples containing individual pollutants such as Cd²⁺ (50-150 μg/L), Cr⁶⁺ (20-80 μg/L) mixture, triclosan (TCS; 0.1-1.0 μg/L) and TCAA (10-80 μg/L), or a mixture of the above. The viability of the sensor was further validated with the actual water sample from the Tuojiang River. The results demonstrated that although the concentration of a single conventional pollutant in water did not exceed the discharge standard for surface water, the comprehensive toxicity of natural water should not be ignored. This method could be a beneficial supplement to conventional water quality detection to understand the characteristics of the water, and thus contribute to the next stage of water treatment.

Deciphering Molecular Factors That Affect Electron Transfer at the Cell Surface of Electroactive Bacteria: The Case of OmcA from Shewanella oneidensis MR-1

Multiheme cytochromes play a central role in extracellular electron transfer, a process that allows microorganisms to sustain their metabolism with external electron acceptors or donors. In Shewanella oneidensis MR-1, the decaheme cytochromes OmcA and MtrC show functional specificity for interaction with soluble and insoluble redox partners. In this work, the capacity of extracellular electron transfer by mutant variants of S. oneidensis MR-1 OmcA was investigated. The results show that amino acid mutations can affect protein stability and alter the redox properties of the protein, without affecting the ability to perform extracellular electron transfer to methyl orange dye or a poised electrode. The results also show that there is a good correlation between the reduction of the dye and the current generated at the electrode for most but not all mutants. This observation opens the door for investigations of the molecular mechanisms of interaction with different electron acceptors to tailor these surface exposed cytochromes towards specific bio-based applications.

Investigation of H2O2 Electrochemical Behavior on Ferricyanide-Confined Electrode Based on Ionic Liquid-Functionalized Silica-Mesostructured Cellular Foam

In this work, ionic liquid (IL) of 1-propyl-3-methyl imidazolium chloride-functionalized silica-mesostructured cellular foam (MCF) was prepared. The obtained MCF-IL was used to construct the Fe(CN)₆^3--confined electrode (MCF-IL-Fe(CN)₆^3-/PVA) and H₂O₂ electrochemical behavior on the electrode was investigated. It was found that H₂O₂ was oxidized on the freshly prepared electrode while catalytically electro-reduced on the acid pretreated one. Cyclic voltametric results revealed that the real catalyst for catalytic reduction of H₂O₂ was Prussian blue (PB) rather than Fe(CN)₆^3-. The electrocatalytic ability of the acid-pretreated MCF-IL-Fe(CN)₆^3-/PVA electrode offered a wide linear range for H₂O₂ detection. The present study on H₂O₂ electrochemical behavior on an MCF-IL-Fe(CN)₆^3-/PVA electrode might provide useful information for further developing integrated Fe(CN)₆^3--mediated biosensors as H₂O₂ is extensively involved in the classic reaction containing oxidase enzymes.

Closed-Loop Microbial Fuel Cell Control System Designed for Online Monitoring of TOC Dynamic Characteristics in Public Swimming Pool

Total organic carbon (TOC) in the water of public swimming pools (PSPs) must be monitored online for public health. In order to address the shortcomings of conventional microbial fuel cell biosensor (MFC-biosensor), an innovative biosensor with peculiar closed-loop structure was developed for online monitoring of TOC in PSPs. Its design was based on experimental data, model identification, cybernetics, and digital and real-time simulation. The outcomes of the digital simulation demonstrated that the closed-loop MFC control system possesses the desired structure with a pair of dominant complex-conjugate closed-loop poles (-15.47 ± 7.73j), and the real-time simulation showed that its controller output signals can automatically and precisely track the variation in TOC concentration in PSP water with the desired dynamic response performances; for example, mean delay time was 0.06 h, rise time was 0.12 h, peak time was 0.18 h, maximum overshoot was 7.39%, settling time was 0.22 h, and best fit 0.98. The proposed principle and method of the closed-loop MFC-biosensor control system in the article can also be applied for online monitoring of other substances in water, such as heavy metal ions, chemical toxicants, and so forth, and lay a theoretical foundation for MFC-based online monitoring substances in an aquatic environment.

Power assisted MFC-based biosensor for continuous assessment of microbial activity and biomass in freshwater ecosystems

Microbial activity and biomass are important factors that determine nutrient and carbon fluxes in freshwater ecosystems and, therefore are also related to both water quality and climate change induced stressors. This study aimed at assessing the feasibility of a power assisted Microbial Fuel Cell (MFC)-based biosensors for the continuous monitoring of microbial activity and biomass concentrations in saturated freshwater ecosystems. For this purpose, four lab-scale reactors were constructed and operated for 30 weeks. Reactors were fed with four different organic matter concentrations to promote a suite of microbial activity and biomass conditions. The reactors consisted of 3.8 L PVC vessels filled with 23 extractable gravel- sockets, used for microbial activity and biomass assessment, and 1 MFC granular-graphite socket, for biosensing assessment. Microbial activity was determined by the ATP content and the hydrolytic enzymatic activity, and the biomass content was assessed as the volatile solids attached to the gravel. Very significant linear relationships could be established between the parameters studied and the current density produced by the MFC with a very short detection time: 10 min for the ATP content (R² = 0.88) and 1 h for the enzymatic activity (R² = 0.78) and biomass (R² = 0.74). Moreover, the power assisted MFC-based biosensing tool demonstrated to be functional after a long operation time and under a wide range of organic loading conditions. Overall, the results highlight the feasibility to develop a power assisted MFC-based biosensor for on-line monitoring of the microbial activity and biomass of a given ecosystem (either natural or artificial) even in remote locations.

Microbiomics for enhancing electron transfer in an electrochemical system

In microbial electrochemical systems, microorganisms catalyze chemical reactions converting chemical energy present in organic and inorganic molecules into electrical energy. The concept of microbial electrochemistry has been gaining tremendous attention for the past two decades, mainly due to its numerous applications. This technology offers a wide range of applications in areas such as the environment, industries, and sensors. The biocatalysts governing the reactions could be cell secretion, cell component, or a whole cell. The electroactive bacteria can interact with insoluble materials such as electrodes for exchanging electrons through colonization and biofilm formation. Though biofilm formation is one of the major modes for extracellular electron transfer with the electrode, there are other few mechanisms through which the process can occur. Apart from biofilm formation electron exchange can take place through flavins, cytochromes, cell surface appendages, and other metabolites. The present article targets the various mechanisms of electron exchange for microbiome-induced electron transfer activity, proteins, and secretory molecules involved in the electron transfer. This review also focuses on various proteomics and genetics strategies implemented and developed to enhance the exo-electron transfer process in electroactive bacteria. Recent progress and reports on synthetic biology and genetic engineering in exploring the direct and indirect electron transfer phenomenon have also been emphasized.

Engineering whole-cell microbial biosensors: Design principles and applications in monitoring and treatment of heavy metals and organic pollutants

Biosensors have been widely used as cost-effective, rapid, in situ, and real-time analytical tools for monitoring environments. The development of synthetic biology has enabled emergence of genetically engineered whole-cell microbial biosensors. This review updates the design and optimization principles for a diverse array of whole-cell biosensors based on transcription factors (TF) including activators or repressors derived from heavy metal resistance systems, alkanes, and aromatics metabolic pathways of bacteria. By designing genetic circuits, the whole-cell biosensors could be engineered to intelligently sense heavy metals (Hg²⁺, Zn²⁺, Pb²⁺, Au³⁺, Cd²⁺, As³⁺, Ni²⁺, Cu²⁺, and UO₂²⁺) or organic compounds (alcohols, alkanes, phenols, and benzenes) through one-component or two-component system-based TFs, transduce signals through genetic amplifiers, and response as various outputs such as cell fluorescence and bioelectricity for monitoring heavy metals and organic pollutants in real conditions, synthetic curli and surface metal-binding peptides for in situ bio-sorption of heavy metals. We further review strategies that have been implemented to optimize the selectivity and correlation between ligand concentration and output signal of the TF-based biosensors, so as to meet requirements of practical applications. The optimization strategies include protein engineering to change specificities, promoter engineering to improve sensitivities, and genetic circuit-based amplification to enhance dynamic ranges via designing transcriptional amplifiers, logic gates, and feedback loops. At last, we outlook future trends in developing novel forms of biosensors.

Cedar Wood-Based Biochar: Properties, Characterization, and Applications as Anodes in Microbial Fuel Cell

In this study, the relationship between pyrolysis temperature of woody biomass and physicochemical properties of derived biochar was investigated for microbial fuel cell (MFC) application. Physical and chemical properties of biochar were characterized for different pyrolysis temperatures. Results showed that biochar obtained at 400 °C was not conductor, while biochars prepared at 600 °C, 700 °C, and 900 °C exhibited decreased electrical resistivity of (7 ± 6) × 10³ Ω.m, (1.8 ± 0.2) Ω.m, and (16 ± 3) × 10^-3 Ω.m, respectively. Rising pyrolysis temperature from 400 to 700 °C exhibited honeycomb-like macroporous structures of biochar with an increase in the specific surface area from 310 to 484 m².g^-1. However, the production of biochar at 900 °C reduced its specific surface area to 136 m².g^-1 and caused the loss of the ordered honeycomb structure. MFCs using anodes based on biochar prepared at 900 °C produced maximum power densities ((9.9 ± 0.6) mW.m^-2) higher than that obtained with biochar pyrolyzed at 700 °C ((5.8 ± 0.1) mW.m^-2) and with conventional carbon felt anodes ((1.9 ± 0.2) mW.m^-2). SEM images of biochar-based anodes indicated the clogging of macropores in honeycomb structure of biochar prepared at 700 °C by growth of electroactive biofilms, which might impede the supply of substrate and the removal of metabolites from the inside of the electrode. These findings highlight that electrical conductivity of biochar is the major parameter for ensuring efficient anodes in microbial fuel cell application. Schematic representation of cedar wood-based biochar and its application as anode in MFC.

Electrogenic Bacteria Promise New Opportunities for Powering, Sensing, and Synthesizing

Considerable research efforts into the promises of electrogenic bacteria and the commercial opportunities they present are attempting to identify potential feasible applications. Metabolic electrons from the bacteria enable electricity generation sufficient to power portable or small-scale applications, while the quantifiable electric signal in a miniaturized device platform can be sensitive enough to monitor and respond to changes in environmental conditions. Nanomaterials produced by the electrogenic bacteria can offer an innovative bottom-up biosynthetic approach to synergize bacterial electron transfer and create an effective coupling at the cell-electrode interface. Furthermore, electrogenic bacteria can revolutionize the field of bioelectronics by effectively interfacing electronics with microbes through extracellular electron transfer. Here, these new directions for the electrogenic bacteria and their recent integration with micro- and nanosystems are comprehensively discussed with specific attention toward distinct applications in the field of powering, sensing, and synthesizing. Furthermore, challenges of individual applications and strategies toward potential solutions are provided to offer valuable guidelines for practical implementation. Finally, the perspective and view on how the use of electrogenic bacteria can hold immeasurable promise for the development of future electronics and their applications are presented.

A critical review on early-warning electrochemical system on microbial fuel cell-based biosensor for on-site water quality monitoring

The microbial fuel cell (MFC) sensor is a very promising self-powered self-sustainable system for early warning water quality detection. These sensors are cost-effective, biodegradable, compact in design, and portable in nature are favorable for real-time in situ water quality monitoring. This review represents the mechanism action behind the toxicity detection, optimization strategies, process parameters, role of biofilm, the role of external resistance, hydrodynamic study, and mathematical modeling for improving the performance of the sensor. Additionally, the techno-economic prospect of this MFC-based sensor and its challenges, limitations are addressed to make it economically more favorable for commercial use. The future direction is also explored based on the sensor's disadvantages and limitations. Comprehensively, this review covered all the possible directions of MFC sensor fabrication, their application, recent advancement, prospects challenges, and their possible solutions.

Detection and Characterization of Bacterial Biofilms and Biofilm-Based Sensors

Microbial biofilms have caused serious concerns in healthcare, medical, and food industries because of their intrinsic resistance against conventional antibiotics and cleaning procedures and their capability to firmly adhere on surfaces for persistent contamination. These global issues strongly motivate researchers to develop novel methodologies to investigate the kinetics underlying biofilm formation, to understand the response of the biofilm with different chemical and physical treatments, and to identify biofilm-specific drugs with high-throughput screenings. Meanwhile microbial biofilms can also be utilized positively as sensing elements in cell-based sensors due to their strong adhesion on surfaces. In this perspective, we provide an overview on the connections between sensing and microbial biofilms, focusing on tools used to investigate biofilm properties, kinetics, and their response to chemicals or physical agents, and biofilm-based sensors, a type of biosensor using the bacterial biofilm as a biorecognition element to capture the presence of the target of interest by measuring the metabolic activity of the immobilized microbial cells. Finally we discuss possible new research directions for the development of robust and rapid biofilm related sensors with high temporal and spatial resolutions, pertinent to a wide range of applications.

Bacterial Competition for the Anode Colonization under Different External Resistances in Microbial Fuel Cells

This study investigated the effect of external resistance (Rext) on the dynamic evolution of microbial communities in anodic biofilms of single-chamber microbial fuel cells fueled with acetate and inoculated with municipal wastewater. Anodic biofilms developed under different Rext (0, 330 and 1000 ohms, and open circuit condition) were characterized as a function of time during two weeks of growth using 16S rRNA gene sequencing, cyclic voltammetry (CV) and fluorescence microscopy. The results showed a drastic difference in power output of MFCs operated with an open circuit and those operated with Rext from 0 to 1000 ohms. Two steps during the bacterial community development of the anodic biofilms were identified. During the first four days, nonspecific electroactive bacteria (non-specific EAB), dominated by Pseudomonas, Acinetobacter, and Comamonas, grew fast whatever the value of Rext. During the second step, specific EAB, dominated by Geobacter and Desulfuromonas, took over and increased over time, except in open circuit MFCs. The relative abundance of specific EAB decreased with increasing Rext. In addition, the richness and diversity of the microbial community in the anodic biofilms decreased with decreasing Rext. These results help one to understand the bacterial competition during biofilm formation and suggest that an inhibition of the attachment of non-specific electroactive bacteria to the anode surface during the first step of biofilm formation should improve electricity production.

Controlling the Carbon-Bio Interface via Glycan Functional Adlayers for Applications in Microbial Fuel Cell Bioanodes

Surface modification of electrodes with glycans was investigated as a strategy for modulating the development of electrocatalytic biofilms for microbial fuel cell applications. Covalent attachment of phenyl-mannoside and phenyl-lactoside adlayers on graphite rod electrodes was achieved via electrochemically assisted grafting of aryldiazonium cations from solution. To test the effects of the specific bio-functionalities, modified and unmodified graphite rods were used as anodes in two-chamber microbial fuel cell devices. Devices were set up with wastewater as inoculum and acetate as nutrient and their performance, in terms of output potential (open circuit and 1 kΩ load) and peak power output, was monitored over two months. The presence of glycans was found to lead to significant differences in startup times and peak power outputs. Lactosides were found to inhibit the development of biofilms when compared to bare graphite. Mannosides were found, instead, to promote exoelectrogenic biofilm adhesion and anode colonization, a finding that is supported by quartz crystal microbalance experiments in inoculum media. These differences were observed despite both adlayers possessing thickness in the nm range and similar hydrophilic character. This suggests that specific glycan-mediated bioaffinity interactions can be leveraged to direct the development of biotic electrocatalysts in bioelectrochemical systems and microbial fuel cell devices.

Innovative air-cathode bioelectrochemical sensor for monitoring of total volatile fatty acids during anaerobic digestion

Bioelectrochemical sensors have proven attractive as simple and low-cost methods with high potential for online monitoring of volatile fatty acids (VFA) in the anaerobic digestion (AD) process. Herein, an innovative dual-chamber air-cathode microbial fuel cell was developed as biosensor for VFA monitoring. The response of the biosensor was nonlinear and increased along with the concentration of VFA mixture increase (2.8-112 mM). Meanwhile, the relationship was linear with low VFA levels (<14 mM) within 2-5 h reaction. High concentrations of bicarbonate decreased the voltage. Stirring speeded up the response and amplified the signal but reduced the saturation concentration (approximately 30 mM) and therefore narrowed the detection range. The applicability of the biosensor was further validated with the effluents from an AD reactor during a start-up period. The VFA concentrations measured by the biosensor were well correlated with the gas chromatographic measurement. The results demonstrate that this biosensor with a novel design could be used for VFA monitoring during the AD process. Based on the 16S rRNA gene sequencing, the dominant microbiomes in the biofilm were identified as Geobacter, Hydrogenophaga, Pelobacter, Chryseobacterium, Oryzomicrobium, and Dysgonomonas.

Microbial fuel cells for in-field water quality monitoring

The need for water security pushes for the development of sensing technologies that allow online and real-time assessments and are capable of autonomous and stable long-term operation in the field. In this context, Microbial Fuel Cell (MFC) based biosensors have shown great potential due to cost-effectiveness, simplicity of operation, robustness and the possibility of self-powered applications. This review focuses on the progress of the technology in real scenarios and in-field applications and discusses the technological bottlenecks that must be overcome for its success. An overview of the most relevant findings and challenges of MFC sensors for practical implementation is provided. First, performance indicators for in-field applications, which may diverge from lab-based only studies, are defined. Progress on MFC designs for off-grid monitoring of water quality is then presented with a focus on solutions that enhance robustness and long-term stability. Finally, calibration methods and detection algorithms for applications in real scenarios are discussed.

A highly sensitive bioelectrochemical toxicity sensor and its evaluation using immediate current attenuation

Electroactive biofilm (EAB) sensor had shown great potential in the field of early warning of toxicants in water because of the low-cost and broad-spectrum. However, the traditional calculation of sensitivity strongly relied on the time and concentration gradient which weakened time-efficiency of the sensor. Moreover, the sensitivity could be further improved to respond trace concentrations. Here EAB sensors with different substrate concentrations were formed to respond different concentrations formaldehyde ranging from 1 ppm to 50 ppm and immediate current attenuation (ICA) was induced to evaluate the sensitivity. The ICA (~70 s) exhibited a shorter time than that calculated by calculable sensitivity (CS) and current attenuation (CA), which not only achieved the response of trace concentration but also improved the time-efficiency of the sensor. The EAB formed with 0.1 g/L acetate (EAB-0.1) had a 380% higher sensitivity than that formed with 1.0 g/L acetate (EAB-1.0), leading to a significant electrochemical toxicity response to 1 ppm of formaldehyde. The results of electrochemical response coefficient confirmed that EAB-0.1 was 1.5-6.3 times of that formed with acetate from 0.2 to 1.0 g/L, which was related with microbial community and component of EAB as described in our previous study. Our findings demonstrated that calculation of sensitivity could be optimized to reflect time-efficiency and EAB with limit acetate could be applied in trace toxicant detection.

Designing of Nanomaterials-Based Enzymatic Biosensors: Synthesis, Properties, and Applications

Among the many biological entities employed in the development of biosensors, enzymes have attracted the most attention. Nanotechnology has been fostering excellent prospects in the development of enzymatic biosensors, since enzyme immobilization onto conductive nanostructures can improve characteristics that are crucial in biosensor transduction, such as surface-to-volume ratio, signal response, selectivity, sensitivity, conductivity, and biocatalytic activity, among others. These and other advantages of nanomaterial-based enzymatic biosensors are discussed in this work via the compilation of several reports on their applications in different industrial segments. To provide detailed insights into the state of the art of this technology, all the relevant concepts around the topic are discussed, including the properties of enzymes, the mechanisms involved in their immobilization, and the application of different enzyme-derived biosensors and nanomaterials. Finally, there is a discussion around the pressing challenges in this technology, which will be useful for guiding the development of future research in the area.

A modelling study of the spatially heterogeneous mutualism between electroactive biofilm and planktonic bacteria

Microbial cooperation widely exists in anaerobic reactors degrading complex pollutants, conventionally studied separately inside the biofilm or the planktonic community. Recent experiments discovered the mutualism between the planktonic bacteria and electroactive biofilm treating propionate, an end-product usually accumulated in anaerobic digesters. Here, a one-dimensional multispecies model found the preference on acetate-based pathway over the hydrogen-based in such community, evidenced by the fact that acetate-originated current takes 66% of the total value and acetate-consuming anode-respiring bacteria takes over 80% of the biofilm. Acetate-based anodic respiration most apparently influences biofilm function while propionate fermentation is the dominant planktonic bio-reaction. Additionally, initial planktonic propionate level shows the ability of coordinating the balance between these two extracellular electron transfer pathways. Increasing the propionate concentration from 2 to 50 mM would increase the steady hydrogen-originated current by 210% but decrease the acetate-originated by 26%, suggesting a vital influence of the planktonic microbial process to the metabolic balance in biofilm. Best strategy to promote the biofilm activity is to increase the biomass density and biofilm conductivity simultaneously, which would increase the current density by 875% without thickening the biofilm thickness or prolonging the growth apparently.

Microbial Electrochemical Systems: Principles, Construction and Biosensing Applications

Microbial electrochemical systems are a fast emerging technology that use microorganisms to harvest the chemical energy from bioorganic materials to produce electrical power. Due to their flexibility and the wide variety of materials that can be used as a source, these devices show promise for applications in many fields including energy, environment and sensing. Microbial electrochemical systems rely on the integration of microbial cells, bioelectrochemistry, material science and electrochemical technologies to achieve effective conversion of the chemical energy stored in organic materials into electrical power. Therefore, the interaction between microorganisms and electrodes and their operation at physiological important potentials are critical for their development. This article provides an overview of the principles and applications of microbial electrochemical systems, their development status and potential for implementation in the biosensing field. It also provides a discussion of the recent developments in the selection of electrode materials to improve electron transfer using nanomaterials along with challenges for achieving practical implementation, and examples of applications in the biosensing field.

Electrochemical and phylogenetic comparisons of oxygen-reducing electroautotrophic communities

The mechanisms of extracellular electron transfer and the microbial taxa associated with the observed electroactivity are fundamental to oxygen-reducing microbial cathodes. Here we confirmed the apparent 'electroautotrophic' behavior of electroactive biofilms (EABs) grown on carbon electrodes at + 0.20V vs. Ag/AgCl under air. The EABs catalyzed O₂ electroreduction into water ─ as demonstrated by a rotating ring disc experiment ─ and performed quasi-reversible heterogeneous electron transfer (HET). By using electrodes of low surface capacitance, we report for the first time nonturnover redox peaks that are very likely intrinsic to the redox protein(s) performing the HET. Because the formal potential of redox proteins is pH-dependent, we investigated the evolution of characteristic potentials of the EABs with the solution pH: (i) open circuit potential, (ii) half-wave potential, and (iii) averaged peak potential of nonturnover cyclic voltammograms, which is presumably the formal potential of the primary electron acceptor(s) for the community. In addition to describing the redox thermodynamics behind HET, we suggest that the corresponding data provides an electrochemical fingerprint that could help in comparing the electroactivity of diverse microbial communities. The taxon with the highest relative abundance in our EABs was an unclassified member of the Gammaproteobacteria that was phylogenetically closely related to most other abundant unclassified Gammaproteobacteria commonly reported in EABs reducing O₂ at high potentials, further suggesting that those taxa are responsible for the bioelectroactivity. Phylogenetic and electrochemical similarities between reported EABs jointly support the hypothesis that similar biomolecular mechanisms may be responsible for this highly probable electroautotrophic metabolism.

Electrolocation? The evidence for redox-mediated taxis in Shewanella oneidensis

Shewanella oneidensis is a dissimilatory metal reducing bacterium and model for extracellular electron transfer (EET), a respiratory mechanism in which electrons are transferred out of the cell. In the last 10 years, migration to insoluble electron acceptors for EET has been shown to be nonrandom and tactic, seemingly in the absence of molecular or energy gradients that typically allow for taxis. As the ability to sense, locate, and respire electrodes has applications in bioelectrochemical technology, a better understanding of taxis in S. oneidensis is needed. While the EET conduits of S. oneidensis have been studied extensively, its taxis pathways and their interplay with EET are not yet understood, making investigation into taxis phenomena nontrivial. Since S. oneidensis is a member of an EET-encoding clade, the genetic circuitry of taxis to insoluble acceptors may be conserved. We performed a bioinformatic analysis of Shewanella genomes to identify S. oneidensis chemotaxis orthologs conserved in the genus. In addition to the previously reported core chemotaxis gene cluster, we identify several other conserved proteins in the taxis signaling pathway. We present the current evidence for the two proposed models of EET taxis, "electrokinesis" and flavin-mediated taxis, and highlight key areas in need of further investigation.

A chip-based 128-channel potentiostat for high-throughput studies of bioelectrochemical systems: Optimal electrode potentials for anodic biofilms

The presence of microorganisms performing extracellular electron transfer has been established in many environments. Research to determine their role is moving slowly due to the high cost of potentiostats and the variance of data with small number of replicates. Here, we present a 128-channel potentiostat, connected to a 128 gold electrode array. Whereas the system is able to perform simultaneously 128 (bio)electrochemical measurements with an independent electrical signal input, the present manufacturing of the array limited the number of effective channels for this study to 77. We assessed the impact of 11 electrode potentials ranging from -0.45V to +0.2V vs. Ag/AgCl (7 replicates per potential) on the growth and electrochemical characteristics of anodic electroactive biofilms (EABs) formed by acetate-fed microbial communities. After 7 days of growth, maximum current was reached for electrodes poised at -0.3V, closely followed by -0.25V and -0.1V to +0.1V, a range well-fitting the midpoint potential of minerals naturally reduced by electroactive bacteria such as Geobacter Sulfurreducens. There was no significant difference in apparent midpoint potential of the EABs (-0.35V), suggesting that the mechanism of heterogeneous electron transfer was not affected by the electrode potential. The EABs poised below current plateau potential (≤-0.3V) exhibited slower growth but higher charge transfer parameters. The high-throughput and high reproducibility provided by the array may have a major facilitating impact on the field of electromicrobiology. Key aspects to improve are data processing algorithms to deal with the vast amount of generated data, and manufacturing of the electrode array itself.

Electroactivity across the cell wall of Gram-positive bacteria

The growing interest on sustainable biotechnological processes for the production of energy and industrial relevant organic compounds have increased the discovery of electroactive organisms (i.e. organisms that are able to exchange electrons with an electrode) and the characterization of their extracellular electron transfer mechanisms. While most of the knowledge on extracellular electron transfer processes came from studies on Gram-negative bacteria, less is known about the processes performed by Gram-positive bacteria. In contrast to Gram-negative bacteria, Gram-positive bacteria lack an outer-membrane and contain a thick cell wall, which were thought to prevent extracellular electron transfer. However, in the last decade, an increased number of Gram-positive bacteria have been found to perform extracellular electron transfer, and exchange electrons with an electrode. In this mini-review the current knowledge on the extracellular electron transfer processes performed by Gram-positive bacteria is introduced, emphasising their electroactive role in bioelectrochemical systems. Also, the existent information of the molecular processes by which these bacteria exchange electrons with an electrode is highlighted. This understanding is fundamental to advance the implementation of these organisms in sustainable biotechnological processes, either through modification of the systems or through genetic engineering, where the organisms can be optimized to become better catalysts.

An electroactive biofilm-based biosensor for water safety: Pollutants detection and early-warning

Besides serving in wastewater treatment and energy generation fields, electroactive biofilm (EAB) has been employed as a sensitive bio-elements in a biosensor to monitor water quality by delivering electrical signals without additional mediators. Increasing studies have applied EAB-based biosensor in specific pollutant detection, typically biochemical oxygen demand (BOD) detection, as well as in early-warning of composite pollutants. Based on a comprehensive review of literatures, this study reveals how EAB outputs electrical signal, how we can evaluate and improve this performance, and what information we can expect from EAB-based biosensor. Since BOD detection and early-warning are normally confusing, this study manages to differentiate these two applications through distinguished purposes and metrics. Based on the introductions of progresses and applications of EAB-based biosensors so far, several novel strategies toward the future development of EAB-based biosensors are proposed.

Immobilisation of electrochemically active bacteria on screen-printed electrodes for rapid in situ toxicity biosensing

Microbial biosensors can be an excellent alternative to classical methods for toxicity monitoring, which are time-consuming and not sensitive enough. However, bacteria typically connect to electrodes through biofilm formation, leading to problems due to lack of uniformity or long device production times. A suitable immobilisation technique can overcome these challenges. Still, they may respond more slowly than biofilm-based electrodes because bacteria gradually adapt to electron transfer during biofilm formation. In this study, we propose a controlled and reproducible way to fabricate bacteria-modified electrodes. The method consists of an immobilisation step using a cellulose matrix, followed by an electrode polarization in the presence of ferricyanide and glucose. Our process is short, reproducible and led us to obtain ready-to-use electrodes featuring a high-current response. An excellent shelf-life of the immobilised electrochemically active bacteria was demonstrated for up to one year. After an initial 50% activity loss in the first month, no further declines have been observed over the following 11 months. We implemented our bacteria-modified electrodes to fabricate a lateral flow platform for toxicity monitoring using formaldehyde (3%). Its addition led to a 59% current decrease approximately 20 min after the toxic input. The methods presented here offer the ability to develop a high sensitivity, easy to produce, and long shelf life bacteria-based toxicity detectors.

Unignorable toxicity of formaldehyde on electroactive bacteria in bioelectrochemical systems

Formaldehyde poses significant threats to the ecosystem and is widely used as a toxicity indicator to obtain electrical signal feedback in electroactive biofilm (EAB)-based sensors. Although many optimizations have been adopted to improve the performance of EAB to formaldehyde, nearly no studies have discussed the toxicity of formaldehyde to EAB. Here, EABs were acclimated with a stable current density (8.9 ± 0.2 A/m²) and then injected with formaldehyde. The current density decreased by 27% and 98% after the injection of 1 and 10 ppm formaldehyde, respectively, compared with that in the control. The ecotoxicity of formaldehyde caused the irreversible loss of current with 3% (1 ppm) and 81% (10 ppm). Confocal laser scanning microscopy and scanning electron microscopy results showed that the redox activity was inhibited by formaldehyde, and the number of dead/broken cells increased from 2% to 40% (1 ppm) and 91% (10 ppm). The contents of the total protein and extracellular polymer substances decreased by more than 28% (1 ppm) and 75% (10 ppm) because of the cleavage reaction caused by formaldehyde. Bacterial community analysis showed that the proportion of Geobacter decreased from 81% to 53% (1 ppm) and 24% (10 ppm). As a result, the current production was significantly impaired, and the irreversible loss increased. Toxicological analysis demonstrated that formaldehyde disturbed the physiological indices of cells, thereby inducing apoptosis. These findings fill the gap of ecotoxicology of toxicants to EAB in a bioelectrochemical system.

How does electron transfer occur in microbial fuel cells?

Microbial fuel cells (MFCs) have emerged as a promising technology for sustainable wastewater treatment coupled with electricity generation. A MFC is a device that uses microbes as catalysts to convert chemical energy present in biomass into electrical energy. Among the various mechanisms that drive the operation of a MFC, extracellular electron transfer (EET) to the anode is one of the most important. Exoelectrogenic bacteria can natively transfer electrons to a conducting surface like the anode. The mechanisms employed for electron transfer can either be direct transfer via conductive pili or nanowires, or mediated transfer that involves either naturally secreted redox mediators like flavins and pyocyanins or artificially added mediators like methylene blue and neutral red. EET is a mechanism wherein microorganisms extract energy for growth and maintenance from their surroundings and transfer the resulting electrons to the anode to generate current. The efficiency of these electron transfer mechanisms is dependent not only on the redox potentials of the species involved, but also on microbial oxidative metabolism that liberates electrons. Attempts at understanding the electron transfer mechanisms will boost efforts in giving rise to practical applications. This article covers the various electron transfer mechanisms involved between microbes and electrodes in microbial fuel cells and their applications.

Environmental-Stress-Induced Increased Softness of Electroactive Biofilms, Determined with a Torsional Quartz Crystal Microbalance

Electroactive biofilms are intensely studied not only for energy conversion and electrosynthesis, but also as sensing systems. The electrical current produced by the layer is largely proportional to the rate of metabolism and therefore decreases when the biofilm experiences adverse environmental conditions. Acoustic measurements may complement this approach. The layer's softness can be inferred from shifts of resonance frequency and resonance bandwidth of a quartz crystal microbalance (QCM) contacting these layers. The layer's softness responds to the environment. Both negative potentials of the electrode (the equivalent of "suffocation") and lack of nutrient supply (the equivalent of "starvation") were studied. For comprehensive analysis, torsional resonators operating on three different modes of vibration are suited best. Such data can be fitted with a viscoelastic model, leading to a quantitative estimate of the shear modulus. On a more empirical level, one might also use the ratio of the shift in bandwidth to the negative shift in frequency as an indicator of stress. For ease of operation, one might even replace the torsional resonators with thickness-shear resonators.

Strategies for improving the electroactivity and specific metabolic functionality of microorganisms for various microbial electrochemical technologies

Electroactive microorganisms, which possess extracellular electron transfer (EET) capabilities, are the basis of microbial electrochemical technologies (METs) such as microbial fuel and electrolysis cells. These are considered for several applications ranging from the energy-efficient treatment of waste streams to the production of value-added chemicals and fuels, bioremediation, and biosensing. Various aspects related to the microorganisms, electrodes, separators, reactor design, and operational or process parameters influence the overall functioning of METs. The most fundamental and critical performance-determining factor is, however, the microorganism-electrode interactions. Modification of the electrode surfaces and microorganisms for optimizing their interactions has therefore been the major MET research focus area over the last decade. In the case of microorganisms, primarily their EET mechanisms and efficiencies along with the biofilm formation capabilities, collectively considered as microbial electroactivity, affect their interactions with the electrodes. In addition to electroactivity, the specific metabolic or biochemical functionality of microorganisms is equally crucial to the target MET application. In this article, we present the major strategies that are used to enhance the electroactivity and specific functionality of microorganisms pertaining to both anodic and cathodic processes of METs. These include simple physical methods based on the use of heat and magnetic field along with chemical, electrochemical, and growth media amendment approaches to the complex procedure-based microbial bioaugmentation, co-culture, and cell immobilization or entrapment, and advanced toolkit-based biofilm engineering, genetic modifications, and synthetic biology strategies. We further discuss the applicability and limitations of these strategies and possible future research directions for advancing the highly promising microbial electrochemistry-driven biotechnology.

Microbial nanowires and electroactive biofilms

Geobacter bacteria are the only microorganisms known to produce conductive appendages or pili to electronically connect cells to extracellular electron acceptors such as iron oxide minerals and uranium. The conductive pili also promote cell-cell aggregation and the formation of electroactive biofilms. The hallmark of these electroactive biofilms is electronic heterogeneity, mediated by coordinated interactions between the conductive pili and matrix-associated cytochromes. Collectively, the matrix-associated electron carriers discharge respiratory electrons from cells in multilayered biofilms to electron-accepting surfaces such as iron oxide coatings and electrodes poised at a metabolically oxidizable potential. The presence of pilus nanowires in the electroactive biofilms also promotes the immobilization and reduction of soluble metals, even when present at toxic concentrations. This review summarizes current knowledge about the composition of the electroactive biofilm matrix and the mechanisms that allow the wired Geobacter biofilms to generate electrical currents and participate in metal redox transformations.

Sequential flowing membrane-less microbial fuel cell using bioanode and biocathode as sensing elements for toxicity monitoring

Traditional microbial fuel cell based biosensor (MFC-Biosensor) utilizes bioanode as sensing element and delivers high sensitivity for single toxic shock but it fails to alert the combined shock of organic matter (OM)/toxic agent (TA). To address this limitation, this study developed a sequential flowing membrane-less MFC based biosensor (SMFC-Biosensor) using both bioanode and biocathode for toxicity monitoring. Results demonstrated the shocks of 1.5 mg/L Hg²⁺, 1.0 mg/L avermectin and 1.0 mg/L chlortetracycline hydrochloride to SMFC-Biosensor led to inhibition ratios of 36%, 15% and 9%, which were over twice higher than those of bioanode-based and biocathode-based MFC-Biosensors. The viabilities of anodic and cathodic biofilms were both inhibited by the toxic shock. Besides, the excessive organic matters caused a decay in the SMFC-Biosensor current and consequently the OM/TA combined shock could be successfully monitored. This study for the first time testified the feasibility of simultaneously using bioanode and biocathode as sensing elements for toxicity monitoring.

The Potential of Bioelectrochemical Sensor for Monitoring of Acetate During Anaerobic Digestion: Focusing on Novel Reactor Design

Acetate as the dominant fraction of volatile fatty acids (VFAs) is an important intermediate in metabolic pathways of methanogenesis, which could reflect the stability status of anaerobic digestion (AD) process. Bioelectrochemical sensors for environmental or bioprocess monitoring have become increasingly attractive in recent years. Although it was more favorable, several challenges still need to be addressed for acetate detection, including large electrode spacing, low stability, biofouling at the cathode and low detection range. In this study, an innovative biosensor on the basis of a three-chamber microbial electrochemical system was proposed to monitor the acetate during the AD process. In such a system, acetate was first transferred from sample chamber through the anion exchange membrane (AEM) to anode due to the driven force of concentration difference and then oxidized by anodic biofilm as a substrate for the current generation. With such design, the influence of waste properties fluctuation in the cathodic reaction could be avoided. The response of current density to different acetate concentrations was investigated. The selectivity, the influence of the sample temperature and the external resistance were also evaluated. The correlation (R 2 > 0.99) between the current densities and acetate concentrations (up to 160 mM) was established at specific reaction time (from 2 to 5 h). Current densities after 5 h reaction were improving about 20% when the sample temperature was high (e.g., 37 and 55°C). The detection range increased along with the decrease of external resistance. The acetate concentrations of AD effluents as determined by the biosensor where within 24.2% of the ones determined by gas chromatography. Nevertheless, the application of the biosensor for monitoring acetate in environmental samples could still be promising.

On-going applications of Shewanella species in microbial electrochemical system for bioenergy, bioremediation and biosensing

Microbial electrochemical system (MES) has attracted ever-growing interest as a promising platform for renewable energy conversion and bioelectrochemical remediation. Shewanella species, the dissimilatory metal reduction model bacteria with versatile extracellular electron transfer (EET) strategies, are the well-received microorganisms in diverse MES devices for various practical applications as well as microbial EET mechanism investigation. Meanwhile, the available genomic information and the unceasing established gene-editing toolbox offer an unprecedented opportunity to boost the applications of Shewanella species in MES. This review thoroughly summarizes the status quo of the applications of Shewanella species in microbial fuel cells for bioelectricity generation, microbial electrosynthesis for biotransformation of valuable chemicals and bioremediation of environment-hazardous pollutants with synoptical discussion on their EET mechanism. Recent advances in rational design and genetic engineering of Shewanella strains for either promoting the MES performance or broadening their applications are surveyed. Moreover, some emerging applications beyond electricity generation, such as biosensing and biocomputing, are also documented. The challenges and perspectives for Shewanella-based MES are also discussed elaborately for the sake of not only discovering new scientific lights on microbial extracellular respiratory but also propelling practical applications.

Regenerated silk fibroin membranes as separators for transparent microbial fuel cells

In recent years novel applications of bioelectrochemical systems are exemplified by phototrophic biocathodes, biocompatible enzymatic fuel cells and biodegradable microbial fuel cells (MFCs). Herein, transparent silk fibroin membranes (SFM) with various fibroin content (2%, 4% and 8%) were synthesised and employed as separators in MFCs and compared with standard cation exchange membranes (CEM) as a control. The highest real-time power performance of thin-film SFM was reached by 2%-SFM separators: 25.7 ± 7.4 μW, which corresponds to 68% of the performance of the CEM separators (37.7 ± 3.1 μW). Similarly, 2%-SFM revealed the highest coulombic efficiency of 6.65 ± 1.90%, 74% of the CEM efficiency. Current for 2%-SFM reached 0.25 ± 0.03 mA (86% of CEM control). Decrease of power output was observed after 23 days for 8% and 4% and was a consequence of deterioration of SFMs, determined by physical, chemical and biological studies. This is the first time that economical and transparent silk fibroin polymers were successfully employed in MFCs.